150 Friction door holder and 150S 160 friction casement stay 160S
Used for windows and glazed doors together with ASSA espagnolette, which has transmission device.
150 and 150S: With fixed frame Material 3. Inward- or outward-opening (applies fixture. Friction runner of zamak. to 150S and 160S). 160 and 160S: with detachable End bearing and frame fixture for 4. Operating catch 4570 (applies frame fixture. 160 and 160S of acetal plastic. to 150S and 160S). 150S and 160S are type-approved Operating catch for 150S and 160S of 5. Frame fixture 5550T, 5580 or as child-safe restrictor according to chrome plated zamak. Plate ASSA 4575 1640, page I 172 (applies to 160 building regulations outlined by the of acetal plastic. and 160S). Swedish National Board of Building, Planning and Housing. Applicable Installation Screw when the key has been removed. Top or bottom, depending on the For friction casing, use espagnolette transmission. no. 5 (3.0 mm) TFX / DIN 7997. Operation and features Instructions for milling, with For frame fixture, use Operated with the espagnolette handle. measurements, page I 172–I 173. no. 7 (3.8 mm) TFX / DIN 7997. With the handle in closed position, For operating catch, use friction holds the sash in the desired When ordering, please state: no. 5 (3.0 mm) TKFX / DIN 7995. airing position. To reduce wear on sash 1. Sash width in frame fold, or and hinges, the casement stay slips standard size according to I 172. when overloaded. With the handle in 2. Right or left. open position, the sash can be moved freely. The friction increases with the opening angle. 160 with detachable frame 150S and 160S have a locking bolt, fixture which limits the opening to allowed airing position with regard to child safety (max 100 mm opening). To open past this position, the detachable key 5550T 5580 must be in place and turned. When the sash is opened, the key is turned before the sash reaches the locking position. The locking function 150 with fixed frame fixture returns automatically when the sash is closed and the key is removed. It also returns by turning the key back manually when closing the sash. Use the plate ASSA 4575 to have per- manently freed locking function (inclu- ded in manipulation fitting ASSA 4570). 150S, (160S) g 4570 Construction a) Friction casing b a X = 43.86 mm b) End bearing c) Locking spindle d) Arm e) Friction runner c f) Frame fixture g) Lock housing (applies to 150S and 160S). e
d Note: f When opening at narrow airing positions 150, (160) (0–200 mm openings), supplement with I ventilation stay ASSA 85, 86 page I 179 Illustration shows left design 4570 or 92, 93 page I 178.
I 171171 Locking casement stay for window and door
150 150S Friction door holder and 160 160S 1650 friction casement stay 5550T 5580
Use and standard sizes Frame fixture 5550T and 5580 (detachable) for 160 and 160S Sash width Standard size Locking spindle Friction Arm max – min 150 150S length at max casing length 160 160S sash width length
140 – 200* 00 192 109 60 201 – 300* 0 0 286 157 100 301 – 400* 1 1 357 202 140 401 – 550 2 2 457 252 205 730 3 587 352 280 551 – 800 3 3 657 352 280 830 4 537 452 450 801 – 1200 4** 4 907 452 450 1101– 1500 5 1083 452 450
Frame fixture *) For sash width less than 400 mm, 1650 the detachment function does not work on 160 and 160S. Frame fixture, fixed for 150 and 150S **) 150/4 and 160/4 are also used for sash widths over 1100 mm, when the opening angle is limited to 60 or 45 degrees. See measurement table, page I 173.
Inward-opening
Upper section with 160+1640 Upper section with 150S
Drill diameter = 14 Sash width
17/29
When milling, the friction casing and espagnolette centre lines must align.
Cross-section X–X
I 172172 150 Friction door holder and 150S 160 friction casement stay 160S
Instructions for milling, 150 and 160 inward-/outward-opening
Sash width Size A B C D Inward Outward 140–200* 00 8 112 25 75 45° – 201–300* 0 12 157 34 115 62° 88° 301–400* 1 34 202 64 155 85° 99° 401–550 2 92 252 108 220 90°±2° 551–800 3 144 352 179 295 90°±2° 801–1200 4 294 452 261 465 90°±2° 1101–1500 5 428 452 388 465 60° – 1101–1500 5 566 452 510 465 45° – *) For sash width less than 400 mm, the detachment function does not work on 160 and 160S.
Instructions for milling, 150S and 160S inward-/outward-opening
Inward-opening Outward-opening Sash width Size A B C D E Inward A B C E Outward 201–300* 0 20 157 40 115 18 78° 20 157 40 18 60° 301–400* 1 42 202 65 155 56 90° 27 202 57 56 90° 401–550 2 99 252 99 220 106 90° 92 252 102 106 90° 551–800 3 144 352 170 295 213 90° 147 352 184 213 90° 801–1200 4 293 452 254 465 321 90° 297 452 263 321 90° 1101–1500 5 425 452 384 465 321 60° * For sash width less than 400 mm, the detachment function does not work on 160 and 160S.
Outward-opening
Drill diameter = 14
Sash width
When milling, the friction casing and espagnolette centre lines must align.
Cross-section Y–Y Cross-section X–X I
I 173173 Locking casement stay for window and door
740 750 Friction casement stay, 760 for Euro-note
Used for window airing position. ASSA 750 and 760 together with ASSA espagnolettes, which have transmission devices.
ASSA 740 with detachable frame fixture. Permanent, adjustable friction. 740 mounted e 750 f a ASSA 750 with fixed frame fixture.
ASSA 760 with detachable frame fixture. b d
Operation and features 740, 760 ASSA 740 holds the sash with permanent friction in the desired airing position. c The friction is adjustable. Adjusted after mounting. ASSA 750 and 760 are operated by using the espagnolette handle. With the handle in closed position, friction holds the sash in the desired airing position. With the handle in open position, the sash moves freely. Installation instruction, inward- Installation instruction, outward- To reduce wear on sash and hinges, opening window opening window the casement stay slips when overloaded.
Construction a) Friction casing Sash width b) End bearing c) Locking spindle Sash width d) Arm e) Friction runner f) Frame fixture
Material Friction runner on ASSA 740 of acetal plastic. Instructions for mounting of ASSA 740 Friction runner on ASSA 750 and 760 of for inward- and outward-opening window zamak. End bearing of zamak. Sash Item Opening A B C Friction Arm Friction casing of anodized aluminium. width no. angle casing length length Other parts of galvanized steel. 301–400 740/1 85 60 70 155 210 140 401–550 740/2 85 110 110 220 260 205 Installation 551–800 740/3 85 160 185 295 360 280 Top or bottom. Instructions for milling, 801–1100 740/4 85 310 265 465 460 450 with measurements, see below. Instructions for mounting of ASSA 750 and 760 Screw for inward- and outward-opening window Cut length Spindle = sash width A-4 For end bearing, use no. 5 (3.0 mm) TFX / DIN 7997. Sash Item Opening A B C Friction Arm Spindle For frame fixture, use no. 7 (3.8 mm) width no. angle casing length length TFX / DIN 7997. length
301–400 750/1 85 45 65 155 207 140 252–351 401–550 750/2 85 100 105 220 257 205 297–446 551–800 750/3 85 150 180 295 357 280 397–646 801–1100 750/4 85 300 260 465 457 450 497–796
I 174174 522 Friction casement stays 532 ASSA 522 and 532
Used for side-hung and top-hung windows.
For outward-opening windows: Construction Installation ASSA 522/1, 522/2. a) Frame fixture. Mounted according to instructions For inward-opening windows: b) Telescope tube. below. ASSA 532/1, 532/2. c) Friction adjustment. d) Rod. Screw Operation and features e) Sash fixture. For frame fixture, use Holds the window with friction in no. 9 (4.5 mm) TFX / DIN 7997. desired open position. Material For sash fixture, use The friction force can be adjusted using Frame and sash fixtures of varnished no. 7 (3.8 mm) TFX / DIN 7997. the friction adjustment device. Fits both steel with cover plate of acetal plastic. right and left. Telescope tube of varnished steel with joint head of acetal plastic. Friction adjustment of acetal plastic. Stainless steel rod with joint head of acetal plastic. White.
Mounting instructions ASSA 522, for outward-opening
522/1, 522/2 522/2 d b c e a
Mounting instructions ASSA 532, for inward-opening
532/1, 532/2 532/2
d e b c a
Frame sight measure Item no. Opening Measure Measure Frame sight measure Item no. Opening Measure Measure min. width mm angle A mm B mm min. width mm angle A mm B mm
260 522/1 c:a 45 58 152 270 532/1 c:a 90 65 152 I 370 522/2 c:a 80 58 262 420 532/2 c:a 90 110 262
I 175175 Locking casement stay for window and door
202 220 Casement stays ASSA 202 and 220
Used for inward-opening windows with sash lipped over frame.
For sash width less than 500 mm: 202, 220 ASSA 202. For sash width over 500 mm: ASSA 220. Desired opening position is fixed with the adjusting screw. Fits both right and b c left. a Construction a) Rod. b) Sash fixture with runner and adjusting screw. c) Rod fixture with pin.
Material Rod of anodized aluminium. Installation Brass adjusting screw with polyamide instructions head. Pin of galvanized brass. Other parts of acetal plastic in white or brown.
Installation Frame width Item Opening Measure Measure Assemble the casement stay for right- mm no. angle A mm B mm or left-hung sash. Push down the rod fixture pin until it snaps in. up to 500 202 c:a 80° 95 75 Mount according to adjacent over 500 220 c:a 80° 190 75 instruction. Measurements from the hinge side. The rod fixture is mounted to place the rod parallel to the sash. 202, 220 Screw For rod fixture, use no. 7 (3.8 mm) TKX / DIN 7996. For sash fixture, use no. 6 (3.5 mm) TKFX / DIN 7995.
202, 220
I 176176 225 Casement stays 230 ASSA 225 and 230
Used for outward-opening windows.
For sash width less than 500 mm: ASSA 225. 225, 230 For sash width over 500 mm: ASSA 230.
Operation and features Desired opening position is fixed with the adjusting screw. Fits both right and left. Can also be used for keeping a separated sash open. Lift the rod pin, separate the rod from the rod fixture and hook it into the plate on the outer frame. c b a Construction a) Rod. b) Frame fixture with runner and Installation adjusting screw. instruction c) Sash fixture with rod pin.
Material Rod of anodized aluminium. Rod pin and adjusting screw of brass with polyamide head. Sash width Item Opening Measure Measure Plate of galvanized steel. Other parts of mm no. angle A mm B mm acetal plastic in white or brown. up to 500 225 c:a 80° 95 75 Installation over 500 230 c:a 80° 170 75 Mounted according to instructions below. Measurements from the hinge side. The rod fixture is mounted to 225, 230 place the rod parallel to the frame. The plate is mounted on the outer sash after making a slot for the rod end.
Screw For rod fixture, use no. 7 (3.8 mm) TKX / DIN 7996. For frame fixture, use no. 6 (3.5 mm) TKFX / DIN 7995. For plate, use no. 4 (2.7 mm) TFX / DIN 7997.
225, 230
I
I 177177 Locking casement stay for window and door
92 93 Ventilation stays ASSA 92 and 93
Type-approved, child-safe.
ASSA 92 for inward-opening windows. 92 for inward-opening window ASSA 93 for outward-opening windows.
Operation and features The fitting has a fixed airing position, which automatically comes into operation when the window is opened. To close the window, push the arm to the side while moving the sash towards a closed position. For openings larger than 100 mm, the fitting can be freed by pushing the arm to the side when it a b is in a certain position. The operation comes back automatically when the window is closed. Fits both right and left.
Construction 92 Uncoupling 92 a) Frame fixture with arm and mounting Uncoupling position plate. b) Sash fixture. Press hard c) Frame fixture. d) Sash fixture with arm. Pin Material Frame/sash fixture and arm of acetal plastic in white or brown.
93 for outward-opening window Installation Mounted to make the opening gap max 100 mm. For the ASSA 92 frame fixture, there are 3 different mounting plates. Fits lipping of 13–20 mm.
Screw d For a and d, use no. 6 (3.5 mm) TFX / DIN 7997 For b and c, use no. 6 (3.5 mm) TKFX / DIN 7995. c
93 Uncoupling
93
I 178178 85 Ventilation stays 85 and 86 86 84 Restrictors 84 and 184 184
ASSA 184 is type-approved, child-safe.
ASSA 85, for inward-opening windows with lipped over sash (also for outward-ope- 85 ning with frame depth less than 32 mm). 50 – 150 ASSA 86, for outward-opening windows. b Operation and features The sash is held in fixed airing posi- tions as the rod and the teeth of the arm catch/frame fixture grip each other. Fits both right and left as the arm a catch/frame fixture can be rotated.
Construction 86
a) Arm with fixture. 50 – 150 b) Sash fixture and arm catch. c) Frame fixture.
Material c Acetal plastic in white or brown. a Installation Mounted according to instructions with measurements. Mounting instructions ASSA 85 ASSA 84 and ASSA 184 when the frame depth is less than 32 mm. For windows and glazed doors, for limiting the opening position.
Operation and features Stops the sash in an open position decided by the position of the restrictor. May be uncoupled by pushing in the spring-operated locking reed while the Outward-opening window Inward-opening window rope is unhooked. Fits both right and left.
Construction ASSA 84 a) Rope fixture with rope and locking knob. b) Locking plate.
Material White polyester rope. Other parts of acetal plastic in white or black.
Construction ASSA 184 (Type-approved, child-safe) a) Wire fixture with plastic coated wire and locking knob. b) Locking plate with cover. 84 184 (Type-approved, child-safe)
Material Wire with plastic coating. Other parts of acetal plastic in white or black. I Screw Use no. 6 (3.5 mm) TKFX/DIN 7995.
971 971 I 971 Locking casement stay for window and door
392 393 Window catches ASSA 392 and 393
For outward-opening windows: Material ASSA 393 Powder painted aluminium. For inward-opening windows: White or brown. Plastic mounting plate. ASSA 392 Key of galvanized steel.
Operation and features Installation Locks the window in narrow airing Plastic template is included. positions. Restricts the opening possibility and increased protection against forced entry and child accident.
May be uncoupled when the frame is closed. For child safety, the uncoupling can be locked with a separate key. Fits side- and top-hung sash and win- dow, H-window type, or pivot window.
I 180180 Window stay restrictor 203 ASSA 203
Used for inward-opening windows with bottom-hung, lipped sash.
Operation and features mounted to place the rod parallel to the 203 c Stops the sash in an open position sash. decided by the position of the window stay restrictor. Fits both right and left. Screw When tilting the sash past the stop For frame fixture, use position, such as for cleaning, the pin no. 7 (3.8 mm) TKX / DIN 7996. is pushed out of its snap-in position, For sash fixture, use which uncouples the rod from its fitting. no. 6 (3.5 mm) TKFX / DIN 7995.
Construction 203 a) Rod. b) Sash fixture with runner. c) Frame fixture with pin.
Material Rod of anodized aluminium. Pin of galvanized brass. Other parts of acetal plastic in white or brown. a Installation Assemble the window stay restrictor for right or left side. Push down the frame fixture pin until it snaps in. The outer frame fixture and the sash fixture are positioned to obtain the desired opening angle. The frame fixture is b 203 mounted
I
I 181181 Locking casement stay for window and door
831 8310 Elbow fittings ASSA 831 and 8310
Used for inward-opening windows with bottom-hung sash.
ASSA 8310 has a catch, which can be Construction locked with a 3 mm Allen key. a) Restrictor. 140, 220, 300, 400 b) Frame fixture. Operation and features c) Sash fixture. Stops the sash in an open position d) Catch. decided by the length and position of the elbow fitting. Fits both right and Material left. When tilting the sash past the stop Stainless steel catch. position, e.g. for cleaning, the catch Other parts of galvanized steel. “Lockable catch” for 8310 is pushed free, which uncouples the elbow fitting from the sash fixture. On Screw ASSA 8310, the Allen screw must first Use no. 7 (3.8 mm) TFX/DIN 7997. be loosened with an Allen key.
Standard lengths Item Item. Milling measurements mm no. no. A B
140 831/140 8310/140 153 150 220 831/220 8310/220 193 190 300 831/300 8310/300 233 230 400 831/400 8310/400 283 280 831 8310 831, 8310
c
d
X minus any clearance
a b
Milling measurements 831, 8310
I 182182 520 Door holder ASSA 520
Used for outward-opening glazed doors.
Operation and features Material Accessories The door is fixed in the desired open Rod of anodized aluminium. Fixing plate ASSA 3976 of galvanized position with the adjusting screw. Brass adjusting screw with polyamide steel, with two sheet metal screws. The stop spring works as a shock head. Pin of galvanized brass. Stop Used for frame depths less than absorber and thereby reduces wear on spring of galvanized spring steel. 30 mm. door and hinges. Fits both right and left. Other parts of acetal plastic in white or brown. Screw Construction For sash fixture, use a) Rod. Installation no. 7 (3.8 mm) TKX / DIN 7996. b) Frame fixture with runner and For opening angle of 90 degrees, For frame fixture, use adjusting screw. mount according to instructions below. no. 6 (3.5 mm) TKFX / DIN 7995. c) Sash fixture with pin. Measurements are made from the For fixing plate, use d) Stop spring. hinge side. The sash fixture is mounted no. 8 (4.0 mm) TFX / DIN 7997. to place the rod parallel to the frame.
3976
520
Installation instructions 520
b d
a c
520 I
I 183183 Locking casement stay for window and door
440 Door holder ASSA 440
Used for holding doors in a fully open position.
Operation and features The door fixture is pressed into the 440 holder in open position to keep the door in this position. a When pulling the door, the holder releases the door fixture.
Construction b a) Holder b) Door fixture
Material Holder of grey age-resistent rubber. Door fixture of acetal plastic.
Installation The holder is mounted on the wall, the door fixture on the door. 440 440
Screw For holder, use no. 12 (5.5 mm) TKX / DIN 7996 For door fixture, use no. 9 (4.5 mm) TKX / DIN 7996
I 184184 523T Friction door holders 533T 534R ASSA 523T, 533T and 534R
Used for external doors, glazed doors, storage room doors, etc. ASSA 523T, for outward-opening doors. ASSA 533T and 534R, for inward-opening doors.
Operation and features 523T 533T, 534R Holds the door with friction in desired open position. Prevents the door from blowing closed and reduces the risk of jam injuries. The friction can be 533T/1 = 430 adjusted with the friction adjuster (on 533T/2 = 530 ASSA 534R, a tool must be used to loosen 534R=400 523T/1 = 445 the lock nut). Fits both right and left. 523T/2 = 545
Construction a) Frame fixture d) Nut M16 b) Telescope tube e) Rod c) Friction adjuster f) Door fixture
Mounting instructions ASSA 523T Material Frame and door fixtures of varnished steel with cover plate of acetal plastic. Varnished steel telescopic tube with joint head of acetal plastic. Friction Frame Item Opening Measure Measure adjuster of acetal plastic (for ASSA 534R: width mm no. angle A mm B mm nut of nickle plated brass and stainless 590–769 523T/1 c:a 95° 130 380 steel friction adjustment). Stainless steel 770–910 523T/2 c:a 95° 210 480 rod with joint head of acetal plastic. Mounting instructions ASSA 533T, 534R Installation Mounted according to instructions below.
Screw Door Item Opening Measure Measure For frame fixture, use width mm no. angle A mm B mm no. 9 (4.5 mm) TFX / DIN 7997. 620–809 533T/1 c:a 95° 190 380 For door fixture, use 810–910 533T/2 c:a 95° 275 480 no. 7 (3.8 mm) TFX / DIN 7997. 570–760 534R c:a 95° 170 350
523T
a b c e f
533T
a
f 534R
f d c a I
I 185185 Locking casement stay for window and door
328 328A Friction door holders ASSA 328 and 328A
Used for storage room doors and lighter internal doors.ASSA 28, for outward-opening doors. ASSA 328A, for inward-opening doors.
Operation and features Holds the door with friction in desired ASSA 328 on closing side ASSA 328A on opening side open position. The friction force can be adjusted using the adjustment nut. The restrictor arm can be loosened from the frame fixture on ASSA 328, and from the door fixture on ASSA 328A, respectively. Fits both right and left.
Construction a) Restrictor arms b) Frame fixture c) Door fixture d) Friction plates e) Spring plate f) Adjustment nut Mounting instructions ASSA 328 Mounting instructions ASSA 328A Material Friction plate of acetal plastic. Other parts of galvanized steel
Installation For 90 degree opening angle, mount according to the adjacent instruction. Frame and door fixtures must align with each other when the door is closed.
Screw Use no. 9 (4.5 mm) TKX/DIN 7996. 328 b a
328 d c
328A b f e 328A
c
I 186186 270 Door holders 271 ASSA 270 and 271
Used for keeping doors in a fully open position, approx. 90 degrees. Max door weight 125 kg.
ASSA 270 270/271 For door width 800–1100 mm. Fits both right- and left-hung door (decided when mounting).
ASSA 271 For door width 1100–1300 mm. For right- and left-hung door.
Operation and features In fully open position (approx. 90 degrees), the catch automatically falls into a locking position and keeps the door in position. When the door is pushed further towards the open position, the catch is released so the 270/271 door can be closed. The stop spring b a also works as a shock absorber and thereby reduces wear on door and hinges.
Construction a) Frame fixture with restrictor arm and runner b) Door rail c c) Catch
Material Mounting of 270/271 Steel, galvanized or galvanized and powder painted white.
Installation 20/20 Surface mounting. Mounting instructions and screw in the package. 160/310 625/700
Mounting of 270/271
225/270
I
I 187187 Locking casement stay for window and door
D110227 D110196 3045 Hinges
Hinge D110227 Pivot hinge ASSA 3045 3045 Used for cupboard doors. Used for rotating windows with horizontal-hung sash. Material Chrome plated zamak. Construction: The friction housing has two rotation points with friction, which cooperate Pivot hinge D110196 from closed position to 180 degrees rotated position. The top rotation point Used for rotating windows with has permanent friction. horizontal-hung sash. The bottom rotation point has adjustable Material friction. The friction housing movement Chrome plated zamak. is such that the rotation points always have the most favourable position in Note: relation to the opening angle of the Max sash weight is 150 kg. sash. This means an even holding and manipulation and gives continuous airing positions. The sash can be lifted into and out of its hinges in the D110227 frame in all positions between 90 and 3045 180 degrees. The hinge only sticks out 18 mm from sash and frame in closed position. Frame fold depth 45 mm Material a) Friction housing, zamak b) Fixing plate for frame fixture, galvanized steel c) Cover strip, acetal plastic d) Front strip, aluminium.
D110196 Friction discs, fibre material. Other 3045 parts, galvanized steel.
Installation Recessed.
Note: Max sash weight is 150 kg.
I 188188