Engineering Plastic ®

Total Page:16

File Type:pdf, Size:1020Kb

Engineering Plastic ® ENGINEERING PLASTIC ® General Engineering Plastic ACRYLIC (PERSPEX) TECAST-T (CAST NYLON) TECADUR (PET) BAKELITE HMWPE-500 TECAMID 6 (NYLON) POLYSTONE PP NYOIL HDPE-300 TECAFORM AH (POM) POLYCARBONATE ABS UHMWPE-1000 TECAMID 66 (PA66) TEFLON EPOXY G10 High Performance Engineering Plastic G 10 ESD TECATOR- PAI PPS PPO- NORYL TAKIRON PVC ESD UHMV-PE CONDUCTIVE TECAPEI-ULTEM TAKIRON PC ESD TORLON ENSITAL- POM SD UHMV-PE ANTI STATIC TURCITE AC-350/450 TECAPEEK VESPEL DELRIN AF ENGINEERING PLASTIC ® General Engineering Plastic Nylon 6 tough, wear- resistant, good vibration-absorption Nylon 6 MoS2 tough, better wear- resistant, and non stick properties than Nylon 6 Nylon 6 Glass Reinforced high strength and rigidity high wear resistance, harder, stiffer and better dimensional stability under Nylon 66 heat than Nylon 6 Nylon 66 Glass Reinforced high rigidity and strength hard, high compressive strength and wear resistance, high degree of Nylon 6 Cast crystallisation Cast Nylon 6 MoS2 very high wear resistance, very hard and rigid high wear resistance, low coefficient of friction - recommended for bearings Cast Nylon 6 Oil Impregnated with pv-value high strength, tough, low creep, better resistance to hydrolysis than Acetal Acetal Copolymer Homopolymer Acetal Homopolymer high strength Acetal Copolymer Glass Reinforced high strength, low thermal expansion, very low water absorption ABS tough, hard, can be galvanized PVC Excellent corrosion resistance, withstands strong acids and alkalis Polycarbonate transparent, tough, low creep, good electrical properties Polycarbonate Glass Reinforced high strength, low thermal expansion PET tough, hard, stable in dimension UHMW PE Excellent wear and abrasions resistance. Low coefficient of friction HDPE Good wear and abrasions resistance. Good electrical insulation. Polypropylene Excellent chemical resistance, good mechanical and electrical properties Fluoropolymer Engineering Plastic Wide temperature range, almost chemically inert, very low coefficient of PTFE friction PVDF high chemical resistant, wear resistant, resistant to UV FEP Chemically inert, weather resistant ECTFE Excellent chemical resistance and mechanical properties PCTFE Excellent chemical resistance and electrical insulating properties PFA Chemical inert, excellent chemical properties and stress resistance ENGINEERING PLASTIC ® High Performance Engineering Plastic very high resistance to deformation under heat, rigid strong, good PEEK dimensional stability PEEK Modified very high chemical resistance, very high dimensional stability Very high resistance to deformation, chemical resistance and dimensional PEEK Glass Reinforced stability PPS Excellent chemical resistance, machines to tight tolerances PPS Glass Reinforced Better thermal performance and dimensional stability than PPS very high resistance to deformation under heat, rigid, strong, good PES dimensional stability very high resistance to deformation under heat, good chemical resistance, PEI transparent, strong, very rigid transparent, good electric properties, high strength, good resistance to PSU deformation at high temperatures, good dimensional stability Exceptional mechanical properties at high temperature. Very high PBI continuous service temperature PBT Good chemical resistance, hard, withstands steam cleaning Excellent wear resistance, withstands harsh thermal and chemical PAI conditions TEMPERATURE GRAPH Material Name Max Operating Temperature oC MACOR GLASS CERAMIC 1000 PBI (POLYBENZIMIDAZOLE) 343 SOLDER PALLET COMPOSITE - SOLIDSTONETM 330 PI (POLYIMIDE) 260 PAI (POLYAMIDEIMIDE) 260 PTFE (POLYTETRAFLUOROETHYLENE) 260 PEEK (POLYETHERETHERKETONE) 260 PPS (POLYPHENYLENESULFIDE) 218 PEI (POLYETHERIMIDE) 171 ANTI-STATIC PHENOLIC - SOLIDLITETM 130 PPSU (Polyphenylsulfone) 149 PCTFE (POLYCHLOROTRIFLUOROETHYELENE) 177 PVDF (POLYVINYLIDENEFLUORIDE) 149 ENGINEERING PLASTIC ® Material Name Max Operating Temperature oC PA 6G (CAST POLYAMIDE) 127 PC (POLYCARBONATE) 121 PA CF (POLYAMIDE CARBON FILLED) 110 PBT (Polybutylene terephthalate) 105 PET (POLYETHYLENE TEREPHTHALATE) 99 PA GF (POLYAMIDE GLASS FILLED) 99 PA 66 (POLYAMIDE, NYLON 66) 99 PA 6 (POLYAMIDE, NYLON 6) 99 PA MOS2 (POLYAMIDE MOLYBDENUM DISULFIDE) 93 PA 6G (CAST POLYAMIDE) 127 PC (POLYCARBONATE) 121 PA CF (POLYAMIDE CARBON FILLED) 110 PBT (Polybutylene terephthalate) 105 PET (POLYETHYLENE TEREPHTHALATE) 99 PA GF (POLYAMIDE GLASS FILLED) 99 PA 66 (POLYAMIDE, NYLON 66) 99 PA 6 (POLYAMIDE, NYLON 6) 99 PA MOS2 (POLYAMIDE MOLYBDENUM DISULFIDE) 93 POM (POLYOXYMETHYLENE) 82 PP (POLYPROPYLENE) 82 PE (POLYETHYLENE) 82 TURCITE TA/TX 82 ACRYLIC (POLY METHYLMETHACRYLATE) 82 PVC (POLYVINYLCLORIDE) 60 ABS (ACRYLONITRILEBUTADIENESTYRENE) 60 PS (POLYSTYRENE) 60 BEARING & WEAR VESPEL® (PolyImide) TECHTRON® (PolyPhenyleneSulfide) TORLON® (PolyAmideImide) TEFLON® (PolyTetraFluoroEthylene) RULON Filled PTFE PEEK BEARING GRADE (PoluEtherEtherKetone) PBT-P (PolyButyleneTerephthalate) PET-P (PolyEthylene Terephtlalate) CAST NYLON (PolyAmide) EXTRUDED NYLON (PolyAmide) ACETAL/DELRIN (PolyAcetal) TURCITE TA PHENOLICS UHMW PE (Ultra High Molecule Weight Polyethylene) ENGINEERING PLASTIC ® SURFACE STATIC RESISTIVITY ANTISTATIC CAST NYLON -MC501 CDR6/R2 ANTISTATIC PEEK -KETRON® PEEK CA30 -SEMITRON® ESD 480 -TECAPEEK CF30 -PEEK MOD ANTISTATIC PVC / PC -ESLON DC -MITSUBISHI SEIDEN PLATE -TAKIRON ANTISTATIC POM -SEMITRON® ESD 225 -ENSITAL® -POMALUX SD -POMALUX CNF ANTISTATIC ULTEM / ULTEM CARBON FILLED -SEMITRON® ESD 410c -SEMITRON® ESD 420 ANTISTATIC PTFE -SEMITRON® ESD 500HR ANTISTATIC PAI -SEMITRON® ESD 520HR ANTISTATIC UHMW PE -TIVAR® 1000 ANTISTATIC -POLYSLICK® 501/502 HIGH TEMPERATURE MACOR MACHINED GRADE CERAMIC PBI (PolyBenzImidazole) VESPEL® PI (PolyImide) TORLON® PAI (PolyAmideImide) TEFLON PTFE (PolyTetraFluoroEthylene) KETRON® PEEK (PolyEtherEtherKetone) TECHTRON® PPS (PolyPhenyleneSulfide) ULTEM® PEI (PolyEtherImide) ENGINEERING PLASTIC ® CHEMICAL RESISTANCE TEFLON PTFE (PolyTetraFluoroEthylene) KEL-F® PCTFE (PolyChloroTrifluoroEthylene) KETRON® PEEK (PolyEtherTherKetone) TECHTRON® PPS (PolyPhenyleneSulfide) PVDF (POLYVINYLIDENEFLUORIDE) PP (PolyPropylene) PVC (PolyVinyliCloride) UHMW PE (Ultra High Molecule Weight PolyEthelene) LOW-OUTGASSING PBI (PolyBenzImidazole) VESPEL® (PolyImide) Duratron XP® (PolyImide) TORLON® 4203 Unfilled (PolyAmideImide) TORLON® 5530 Glass-Filled (PolyAmideImide) SEMITRON® ESD 500HR (Filled PTFE) KEL-F® PCTFE (PolyChloroTrifluoroEthylene) KETRON® PEEK (PolyEtherTherKetone) TECHTRON® PPS (PolyPhenyleneSulfide) ULTEM® PEI (PolyEtherImide) SEMITRON® ESD 410c (Filled PolyEtherImide) Ertalyte® PET-P (PolyEthylene Terephtlalate) SEMITRON® ESD 225 (AntiStatic Acetal) .
Recommended publications
  • Quadrant EPP Cestilene™ HD 1000 Polyethylene Datasheet
    www.lookpolymers.com email : [email protected] Quadrant EPP Cestilene™ HD 1000 Polyethylene Category : Polymer , Thermoplastic , Polyethylene (PE) , HDPE , High Density Polyethylene (HDPE), Injection Molded Material Notes: Data provided by Quadrant Engineering Plastic Products for polymers in their European product line. Order this product through the following link: http://www.lookpolymers.com/polymer_Quadrant-EPP-Cestilene-HD-1000-Polyethylene.php Physical Properties Metric English Comments Density 0.930 g/cc 0.0336 lb/in³ ISO 1183 Water Absorption 0.010 % 0.010 % immersion Mechanical Properties Metric English Comments Hardness, Shore D 60 60 after 15 sec.; ISO 868 62 62 after 3 sec.; ISO 868 Ball Indentation Hardness 36.0 MPa 5220 psi ISO 2039-1 Tensile Strength, Yield 19.0 MPa 2760 psi ISO 527 Elongation at Break >= 50 % >= 50 % ISO 527 Elongation at Yield 15 % 15 % ISO 527 Tensile Modulus 0.750 GPa 109 ksi ISO 527 Compressive Yield Strength 4.50 MPa 653 psi at 1% nominal strain; ISO 604 8.00 MPa 1160 psi at 2% nominal strain; ISO 604 14.0 MPa 2030 psi at 5% nominal strain; ISO 604 Charpy Impact Unnotched NB NB ISO 179/1eU Charpy Impact, Notched 11.0 J/cm² 52.4 ft-lb/in² Partial Break; ISO 179/1eA Abrasion 100 100 Relative loss per DSM internal test (CESTILENE HD 1000 = 100) Thermal Properties Metric English Comments 175 - 225 µm/m-°C 97.2 - 125 µin/in-°F CTE, linear @Temperature 20.0 °C @Temperature 68.0 °F Thermal Conductivity 0.400 W/m-K 2.78 BTU-in/hr-ft²-°F Melting Point 130 - 135 °C 266 - 275 °F ISO 3146; DSC, 10°C/min
    [Show full text]
  • Engineered-Plastics.Pdf
    PLASTIC PLASTICS REFERENCE HANDBOOK REGAL PLASTIC SUPPLY COMPANY PLASTICS REFERENCE HANDBOOK Copyright 1999—2000 Regal Plastic Supply Company, a division of Regal Supply Company INTRODUCTION Established in 1954, Regal Plastic Supply Company is considered one of the foremost pioneers in the plastic distribution industry. Throughout the years, the innovative “customer- oriented plan for success” thinking has become a credible trademark our customers rely on. Fortifying that philosophy, Regal introduced its Plastic Materials Reference Guide in 1984. As products and industries continue to evolve, so does this compilation of technical data. We view providing our customers with tools for effective planning and purchasing as important as meeting product “supply and demand”. You will find this guide an invaluable reference source for researching or finding the answer pertaining to your plastic application. The product information contained herein covers the most commonly used materials; it does not reflect our total capacity. True customer service is a thought process not developed overnight. Our experience and stability in the industry gives Regal the opportunity to assist you in your plastics endeavors as you utilize staff who are accessible, knowledgeable and resourceful with regard to all inquiries. We invite you to visit the Regal Plastic Supply Company location in your vicinity. All locations maintain generous inventories of plastic sheet, rod, tube, film, and numerous finished products. Regal Plastic Supply Company thanks all of our customers for their patronage over the years. We will continue in our efforts to provide the best in JIT inventory and personal service. Plastic is in your future and Regal Plastic Supply Company is your best source.
    [Show full text]
  • Brominated Polystyrene(BPS) FR
    Brominated Polystyrene(BPS) FR Description Product Name : Brominated Polystyrene(BPS) Equivalent Name : Albermarle Saytex HP3010 ; Albermarle Saytex HP7010 ; Dead Sea FR‐803P Cas No. : 88497‐56‐7 Application It provides outstanding thermal stability and electrical performance. It is particularly suitable for engineering plastic applications such as polyesters (PET, PBT, PCT) and PA (nylons).it has outstanding thermal stability. It is an ideal choice for high temperature applications such as engineering plastics. Due to its stability, it can often be used where other flame retardants fail to survive. Due toits polymeric structure, it is non‐blooming in all applications. Excellent electrical properties provide yet another reason to choose this flame retardant for demanding engineering plastic applications. Benefits and Features Excellent Flow In Resin,Superior Color,Excellent Thermal Stability, Excellent Melt Stability, Excellent Non Blistering Performance, Improved Mechanical Properties,Low Loading Typical Properties BPS 3010 Appearance .............................................................................................................................................................. White grain/ yellowish powder. Content % ..........................................................................................................................................................................................................66 min. Melting point °C .............................................................................................................................................................................................
    [Show full text]
  • The Recent Developments in Biobased Polymers Toward
    polymers Review The Recent Developments in Biobased Polymers toward General and Engineering Applications: Polymers that Are Upgraded from Biodegradable Polymers, Analogous to Petroleum-Derived Polymers, and Newly Developed Hajime Nakajima, Peter Dijkstra and Katja Loos * ID Macromolecular Chemistry and New Polymeric Materials, Zernike Institute for Advanced Materials, University of Groningen, Nijenborgh 4, 9747 AG Groningen, The Netherlands; [email protected] (H.N.); [email protected] (P.D.) * Correspondence: [email protected]; Tel.: +31-50-363-6867 Received: 31 August 2017; Accepted: 18 September 2017; Published: 18 October 2017 Abstract: The main motivation for development of biobased polymers was their biodegradability, which is becoming important due to strong public concern about waste. Reflecting recent changes in the polymer industry, the sustainability of biobased polymers allows them to be used for general and engineering applications. This expansion is driven by the remarkable progress in the processes for refining biomass feedstocks to produce biobased building blocks that allow biobased polymers to have more versatile and adaptable polymer chemical structures and to achieve target properties and functionalities. In this review, biobased polymers are categorized as those that are: (1) upgrades from biodegradable polylactides (PLA), polyhydroxyalkanoates (PHAs), and others; (2) analogous to petroleum-derived polymers such as bio-poly(ethylene terephthalate) (bio-PET); and (3) new biobased polymers such as poly(ethylene 2,5-furandicarboxylate)
    [Show full text]
  • Environmental Biodegradability of Recombinant Structural Protein
    www.nature.com/scientificreports OPEN Environmental biodegradability of recombinant structural protein Yuya Tachibana1,2*, Sunita Darbe3, Senri Hayashi1, Alina Kudasheva3, Haruna Misawa1, Yuka Shibata1 & Ken‑ichi Kasuya1,2* Next generation polymers needs to be produced from renewable sources and to be converted into inorganic compounds in the natural environment at the end of life. Recombinant structural protein is a promising alternative to conventional engineering plastics due to its good thermal and mechanical properties, its production from biomass, and its potential for biodegradability. Herein, we measured the thermal and mechanical properties of the recombinant structural protein BP1 and evaluated its biodegradability. Because the thermal degradation occurs above 250 °C and the glass transition temperature is 185 °C, BP1 can be molded into sheets by a manual hot press at 150 °C and 83 MPa. The fexural strength and modulus of BP1 were 115 ± 6 MPa and 7.38 ± 0.03 GPa. These properties are superior to those of commercially available biodegradable polymers. The biodegradability of BP1 was carefully evaluated. BP1 was shown to be efciently hydrolyzed by some isolated bacterial strains in a dispersed state. Furthermore, it was readily hydrolyzed from the solid state by three isolated proteases. The mineralization was evaluated by the biochemical oxygen demand (BOD)‑ biodegradation testing with soil inocula. The BOD biodegradability of BP1 was 70.2 ± 6.0 after 33 days. Many commercially available polymers have some associated environmental problems1,2. Te increase in the production and subsequent disposal of synthetic polymers causes serious environmental pollution because these polymers do not degrade in the natural environment.
    [Show full text]
  • Compatibility of Refrigerants and Lubricants with Engineering Plastics
    DOE/CE/23810-15 COMPATIBILITY OF REFRIGERANTS AND LUBRICANTS WITH ENGINEERING PLASTICS Final Report Richard C. Cavestri, Ph.D. Imagination Resources, Inc. 5130 Blazer Memorial Parkway Dublin, Ohio 43017 September 1993 Prepared for The Air-Conditioning and Refrigeration Technology Institute Under ARTI MCLR Project Number 650-50600 This project is supported, in whole or in part, by U.S. Department of Energy grant number DE-FG02-91CE23810: Materials Compatibility and Lubricants Research (MCLR) on CFC-Refrigerant Substitutes. Federal funding supporting this project constitutes 93.67% of allowable costs. Funding from non-government sources supporting this project consists of direct cost sharing of 6.33% of allowable costs; and in-kind contributions from the air-conditioning and refrigeration industry. DISCLAIMER The U.S. Department of Energy's and the air-conditioning industry's support for the Materials Compatibility and Lubricants Research (MCLR) program does not constitute an endorsement by the U.S. Department of Energy, nor by the air-conditioning and refrigeration industry, of the views expressed herein. NOTICE This report was prepared on account of work sponsored by the United States Government. Neither the United States Government, nor the Department of Energy, nor the Air-Conditioning and Refrigeration Technology Institute, nor any of their employees, nor of any of their contractors, subcontractors, or their employees, makes any warranty, expressed or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product or process disclosed or represents that its use would not infringe privately-owned rights. COPYRIGHT NOTICE (for journal publication submissions) By acceptance of this article, the publisher and/or recipient acknowledges the right of the U.
    [Show full text]
  • (Bio)Degradable Polymers from Renewable Resources
    International Conference (Bio)Degradable Polymers from Renewable Resources Vienna, November 18 – 21, 2007 ABSTRACTS Polish Academy of Sciences Scientific Centre in Vienna The Conference is held under auspices of the European Polymer Federation Sponsors Polish Academy of Sciences Polska Akademia Nauk Ministry of Science and Higher Education, Poland Ministerstwo Nauki i Szkolnictwa Wyzszego˙ Federal Ministry of Transport, Innovation and Technology, Austria Bundesministerium für Verkehr, Innovation und Technologie ACS PUBLICATIONS HIGH QUALITY. HIGH IMPACT. CONTENTS Conference Committees and Organizers . 5 Conference Programme . 6 Conference Venues. .8 Overview of Abstracts . 9 Abstracts of Invited Lectures. .13 Abstracts of Poster Contributions . 33 Author Index . 108 List of Participants . 111 SCIENTIFIC COMMITTEE Ann-Christine Albertsson (Sweden) – co-Chair Gerhart Braunegg (Austria) – co-Chair Francesco Ciardelli (Italy) Danuta Ciechanska (Poland) Andrzej Dworak (Poland) Zbigniew Florjanczyk (Poland) Shiro Kobayashi (Japan) Izabella Krucinska (Poland) Andrej Krzan (Slovenia) Christopher K. Ober (USA) Gabriel Rokicki (Poland) Tadeusz Spychaj (Poland) Robert F. Stepto (UK) Piotr Tomasik (Poland) Jean-Pierre Vairon (France) Danuta Zuchowska (Poland) Chairman of the Conference Stanislaw Penczek Chairman of the Organizing Committee Stanislaw Slomkowski Conference Secretary Andrzej Nadolny CO-ORGANIZERS OF THE CONFERENCE Polish Academy of Sciences, Scientific Centre in Vienna, Austria International Network (Bio)degradable Polymers from Renewable
    [Show full text]
  • FACT SHEET European Bioplastics
    FACT SHEET European Bioplastics Bio-based plastics in the automotive market – clear benefits and strong performance Overview of materials and market development Cutting fuel consumption and emissions by reducing a vehi- b. Bio-based technical performance polymers e.g. cle’s weight is a central objective and major challenge for the polytrimethylene terephthalate (PTT) or thermoplastic automotive industry. Bioplastics materials are well suited to copolyester elastomers (TPC-ET) or bio-based poly- contributing towards this goal. Leading automotive brands amides around the world are already using bio-based plastics (e.g. bio- based polyamides, bio-based polyesters, etc.) with the aim of 2. Plastics that are both bio-based and biodegradable e.g. reducing their products’ environmental impact. polylactic acid (PLA), polyhydroxyalkanoates (PHA) and polybutylene succinates (PBS), but can also be used in durable This fact sheet presents an overview of available bio-based applications. plastic materials, general benefits of bio-based plastics, bio- based plastics market development, and bio-based plastic per- Several bio-based plastics are used in the automotive market, formance in the automotive sector. including bio-based polyamides, PTT and bio-based polyole- fines as well as PLA-blends. What are bio-based plastics? Benefits of bio-based plastics Bio-based plastics comprise a range of materials with differing properties1: Saving scarce resources, counting on renewable feedstock 1. Bio-based or partially bio-based, non-biodegradable Bio-based plastics help to reduce the dependency on limited (i.e. durable) plastics such as fossil resources, which are expected to increase in price sig- nificantly over the coming decades.
    [Show full text]
  • Material Selection Selection
    alroplastics.com 800-877-ALRO 2 5 7 6 Material Selection Selection Advantages of Stock Shapes ...............................................10 Material General Selection Criteria ...............................................10-11 Product Descriptions ..................................................... 12-15 Product Selection Chart ................................................. 16-19 IAPD Thermoplastic Rectangle ...................................... 20-21 Property Comparison Charts Slide Wear .......................................................................22 Rotational Wear ..............................................................22 Temperature, Continuous Use .......................................23 Friction Comparison .......................................................23 Tensile Strength ..............................................................24 Impact Resistance ..........................................................24 Thermal Dimensional Stability ......................................25 Moisture Dimensional Stability .....................................25 Hardness Comparison ...................................................26 Weight Comparison ........................................................26 WARNING: These products can potentially expose you to chemicals including, 4-Dioxane, Acetaldehyde, Acrylonitrile, Bisphenol-A, Carbon Black, Chromium, Cumene, Dichloromethane, Ethyl Acrylate, Ethylbenzene, Ethylene Glycol, Formaldehyde, Glass Fibers, Hexachlorobenzene, Lead, Methanol, Nickel, Polyvinyl
    [Show full text]
  • Engineering Plastics – the Manual This Manual Is Designed to Provide Readers with a Compact Outline of Our Extensive Fund of Plastics-Related Knowledge
    Stock shapes Engineering plastics – The Manual This manual is designed to provide readers with a compact outline of our extensive fund of plastics-related knowledge. Alongside a grounding of theoretical facts and informa- tion, the manual also provides a range of practical tips and material recommendations, together with calculation ex- amples for component design and advice on the further processing of plastics. 4 Overview of plastics 6 Classification of plastics 7 Ensinger process chain 8 Processing methods Materials 12 TECARAN ABS 13 TECANYL 14 TECAFINE PE 15 TECAFINE PMP 16 TECAPRO MT / TECAFINE PP 18 TECAFORM 20 TECAMID 22 TECAST / TECARIM 24 TECADUR / TECAPET 26 TECANAT 28 TECAFLON 30 TECAPEI 32 TECASON S, P, E 34 TECATRON 36 TECAPEEK 38 TECATOR 40 TECASINT Properties 44 Modifications / additives 46 Thermal properties 50 Mechanical properties 54 Processing influences 55 Tribological characteristics 57 Electrical properties 60 Chemical resistance 62 Moisture absorption 63 Flame retardant classification 64 Radiation resistance 66 Certifications and approvals Material selection and calculations 70 Material selection 72 Calculations Further processing This manual is designed to provide readers with a compact 76 Processing plastics outline of our extensive fund of plastics-related knowledge. 77 Machining guidelines Alongside a grounding of theoretical facts and informa- 78 Tempering tion, the manual also provides a range of practical tips and 80 Welding material recommendations, together with calculation ex- 82 Gluing amples for component
    [Show full text]
  • Impact Behaviour of Acrylonitrile-Butadiene-Styrene After Temperature and Humidity Load
    MATEC Web of Conferences 125, 02048 (2017) DOI: 10.1051/ matecconf/201712502048 CSCC 2017 Impact behaviour of acrylonitrile-butadiene-styrene after temperature and humidity load Lenka Hylova 1,*, Miroslav Manas1 1Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic Abstract. This study deals with acrylonitrile-butadiene-styrene (ABS) which was subjected the drop-weight test before and after temperature and humidity load. ABS is an engineering plastic and also an important engineering terpolymer, which has butadiene part uniformly distributed through the acrylonitrile-styrene matrix and is commonly used in production of automotive interior components. The injection moulded ABS samples were subjected the penetration test at fall height 100 J before and after temperature and humidity load and the results were subsequently evaluated and discussed. It was found out that ABS after temperature and humidity load has lower impact resistance. 1 Introduction construction, computer and business equipment, personal care products, toys, medical devices and in automotive Acrylonitrile-butadiene-styrene (ABS) is an engineering interior components [1-3]. plastic and also an important engineering terpolymer, Brazilian scientists investigated three types of which has butadiene part uniformly distributed through commercial ABS, namely GP (ABS for general-purpose the acrylonitrile-styrene matrix. ABS was use), HI (an ABS high impact) and HH (ABS high heat commercialized at the latter of 1940s by U.S. Rubber and resistance). They studied activation energy of all three originally was made by blending of polystyrene-co- ABS and they realized that it is much higher than acrylonitrile (SAN) and NBR acrylonitrile-butadiene reported in the literature.
    [Show full text]
  • Engineering Plastics for Food Processing and Packaging Equipment
    Engineering Plastics for Food Processing and Packaging Equipment A guide to materials that meet the industry's need for More and Faster production. ® You inspire … wewww.quadrantplastics.com materialize You inspire... we materialize Quadrant history: The first engineering polymer shapes for machining. Quadrant today: The broadest range of engineering polymer shapes allowing the most effective material choice. Quadrant tomorrow: New products for new needs, developed by QEPP’s global product and application development team. For over 60 years, the companies that today form Quadrant have been developing new materials to meet changing demands of customers around the world. The innovative, collaborative spirit between our people and our customers has shaped our success and led to the industry’s broadest range of engineering plastic shapes for machining. Our investment in innovation will only increase in the years ahead, to support your requirements for higher levels of performance, productivity and value. Quadrant Engineering Plastics - Global Scope 2 www.quadrantplastics.com Content More. Faster 4 TECHNICAL SUPPORT FROM CONCEPT THROUGH PRODUCTION 5 QUALITY SYSTEMS THAT ENSURE CONSISTENCY 5 Engineering Plastic Temperature Performance Groups 6 < 80°C APPLICATIONS 7-8 80 - 120°C APPLICATIONS 9-12 120 - 160°C APPLICATIONS 13-14 > 160°C APPLICATIONS 15 PHYSICAL PROPERTIES 16-17 CLEANING AND SANITISING 18 www.quadrantplastics.com 3 More. Faster. IN THE FOOD PROCESSING AND PACKAGING INDUSTRY, IT MEANS... • Higher demands on the components in your equipment • More frictional heat, more wear, more aggressive, hotter cleaning • A whole new game in material selection FASTER means hotter, and some traditional materials can't take it.
    [Show full text]