PRODUCT DATA SHEET PROD . #900 SERIES RICH TIMBER TUFF 100% ACRYLIC SOLID BODY

PRODUCT DESCRIPTION Rich Wood Timber Tuff 100% Acrylic Solid Body Wood Stain is a specially formulated, 100% acrylic solid body wood stain that incorporates the qualities of a low temperature stain , approved to be applied at temperatures down to 35°F, along with the benefit of being a and primer in one. Formulated with advanced resin technology, it promotes superior durability, excellent color retention, and excellent weather resistance. It is easy to apply, provides excellent one coat coverage while enhancing the wood grain, and resists streaking, and fading. It is non-yellowing, mildew resistant, formulated to withstand variable temperature changes allowing for application in different climate types, making it ideal for both interior and exterior applications. Mildew Resistant - This paint contains agents that inhibit the growth of mildew on the surface of this paint film.

PRODUCT FEATURES PRODU CT USES PERFORMANCE QUALITIES VOC COMPLIANCE • 100% Acrylic Formula Suitable for the following properly prepared surfa ces; Product Quality: Premium / Best AIM Yes • Low Temp Application 35 º F INTERIOR / EXTERIOR Product Use: Interior / Exterior OTC Yes • Self Priming Wood Doors Fencing Application: Brush, Roller Cover, CARB Yes • One Coat Coverage Wood Trim Decks & Railings Airless Spray SCAQMD Yes • Excellent Durability Shutters Beams & Furniture Product System: Water-Based MPI # N/A • Excellent Weather Siding Shelves Finish: Flat LEED® 09CI N/A Resistance Shakes & Shingles Assorted Masonry LEED® 09NC N/A • Mildew Resistant LEED® 09CS N/A • Easy To Apply Greta For Both Interior & Exterior Use! LEED® H N/A

SURFACE PREPARATION TECHNICAL DATA General: • COLORS: White & Tint Bases • The entire surface area to be painted should be clean, dry, sound and free from dirt, grease, oils, 90 0 White 90 1 Tint Base waxes, mildew, and any other surface contaminants that may adversely affect the performance of 90 2 Deep Base 90 3-A Accent Base this coating material. • New Wood Substrates – For wood surfaces, remove all surface stains, dirt, oxidized stains, • TINTING: Universal Colorants organic growth, and loose wood fibers. Remove loose splinters, and replace any severely rotted or damaged wood. New wood surfaces should be painted immediately after installation. Do not allow • VEHICLE TYPE: Acrylic the wood to weather. Weathered wood surfaces should be sanded to a fresh wood surface before coating. Remove any grade stamps or pencil marks from new wood by lightly sanding. Wood • VISCOSITY: 90 KU ± 2 moisture content should be below 15% and wood surfaces that have a mill glaze should be sanded to allow for proper adhesion. • GLOSS @ 60 E: Flat / 0 – 5 units • Although Timber Tuff is formulated to be self-priming on most , some wet woods, such as Cedar and Redwood, should be allowed to weather sufficiently for up to 6 months prior to • FLASH POINT: N/A or staining, otherwise prime the surface with Richard’s #7-22, PPS Universal Alkyd Primer/Sealer Enamel Undercoater. • VOC: Not to Exceed 250 g/l – 2.10 lb/gal • Previously Painted/Stained Wood Substrates – As stated above, the entire surface area to be (Meets AIM, OTC, CARB, & SCAQMD Standards ) painted should be thoroughly cleaned. Remove any loose, scaling, chalked, cracked or peeling paint by hand scraping, sanding, wire brushing or by power tool cleaning methods, such as • SOLIDS: By Volume: 31.25% ± 2% pressure washers, electric sanders, etc. Repair/replace any damaged, deteriorated and surface By Weight: 45.58% ± 2% imperfections with the proper patching compounds and/or building materials. Normally, priming is not necessary unless the surface is chalking or showing signs of deterioration. Surfaces displaying • COVERAGE: 200 – 400 Sq. Ft. / Gal. these conditions should be primed with Richard’s #7-44, PPS 100% Universal Primer/Sealer Stain (Depending on Application & Surface Porosity. ) Sealer. Glossy surfaces should be dulled. Mildew - Surface areas affected by mildew should be treated with a commercial mildew removal and/or • MIL FILM: Estimated @ 300 Sq. Ft. / Gal. wash product carefully following manufacturer’s application and safety directions. Rinse thoroughly with Wet: 5.3 mils Dry: 1.7 mils clean water, and allow a minimum of 24 hours to dry thoroughly. • WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST • DRY TIME: (@ 70º F & 50% Relative Humidity) CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD To Touch: 2 – 4 Hours ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator to control lead exposure. Clean up carefully with a HEPA Recoat: 4 – 6 Hours, or after overnight dry. vacuum and wet mop. Before you start, find out how you can protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-Lead, or log onto www.epa.gov/lead . • CLEAN UP: Warm Soapy Water PRODUCT ANALYSIS DATA • THINNING: Clean Water PIGMENT: 25.60% VEHICLE: 74.40%

MORE DETAILED PRODUCT ANALYSIS DATA IS AVAILABLE UPON REQUEST .

RICHARD’S PAINT MANUFACTURING COMPANY, INC. • 200 PAINT STREET • ROCKLEDGE, FL 32955 Tel: 321-636-6200 • Fax: 321-633-0866 • Toll Free: 800-432-0983 • Web Site: www.richardspaint.com RICH WOOD TIMBER TUFF 100% ACRYLIC SOLID BODY WOOD STAIN / PROD . #900 SERIES - PRODUCT DATA SHEET PAGE 2

RECOMMENDED PRIMER PRODUCT APPLICATION – General Although formulated to be self-priming on most properly prepared new and Rich Wood Timber Tuff 100% Acrylic Solid Body Wood Stain may be easily previously painted wood surfaces in good condition, the following Richard’s applied with a quality brush, roller cover, or airless spray equipment as follows; products are recommended primer coatings for this finish coating material. • Stir thoroughly in a spiral up and down motion before and during application. • For best results, it is recommended to apply by brush or roller to effectively • New Wood: work stain into wood pores. • Self-Priming • To assure color uniformity intermix multiple containers of custom tinted and • 7-22, PPS Universal Alkyd Primer/Sealer Enamel Undercoater stock colors, and apply a small test area to verify color. • 7-44, PPS 100% Acrylic Universal Primer/Sealer Stain Killer • When applying by brush or roller, apply an even and generous coat with the • New Wet Woods direction of the wood grain. • 7-22, PPS Universal Alkyd Primer/Sealer Enamel Undercoater • When staining vertical wood siding, start at the top, applying stain to two or • 7-44, PPS 100% Acrylic Universal Primer Sealer Stain Killer three boards, and work down to the bottom of the boards or until you come to • Previously Painted Surfaces: a natural break in the surface, such as a corner or edge. • Self-Priming • When staining horizontal wood siding, start at the top corner, applying stain • 7-44, PPS 100% Acrylic Universal Primer/Sealer Stain Killer to two or three boards, and work across to the other end of the boards or until you come to a natural break in the surface, such as a corner or edge. APPLICATION EQUIPMENT • When applying by airless spray equipment use a unit with a minimum of 2000 psi of pressure, and a 0.017” – 0.019” fluid spray tip. • Brush Application: Apply using a quality nylon, polyester, or combination • During spray application, it is recommended to back-roll the surface area to nylon/polyester bristle brush. ensure an even coat application, and to effectively work stain into wood pores. • Roller Application: Apply using a ½” - 1” nap synthetic or lamb’s wool • To assure coating uniformity, always paint to a natural break in the surface, roller cover, depending on the texture and surface porosity. such as a corner or edge, and maintain a wet edge during application by brushing, rolling or spraying into previously applied coating area. • Spray Application: • Avoid exterior paint application when weather conditions are threatening, and • Pump: Gas or Electric Airless Sprayer late in the day when there is a threat of moisture condensing on newly • Tip: 0.017” – 0.019” Reversible painted surfaces. • Pressure: Minimum 2000 psi • Apply when surface and ambient temperatures are above 55° F and below ⅜ • Hose: ¼ inch (6.3 mm) - inch (10 mm) 90° F. Note: Deep & Accent bases must be applied at temperatures above 50 º F. PACKAGING & WEIGHT PER GALLON • Packaging: Quarts – 6/case Gallons – 4/case PRODUCT LIMITATIONS 2 Gallons – N/A 5 Gallons - Each • Not for use in corrosive or chemical environments. • Not for use in areas subject to intense heat. • Weight Per Gallon: 10.58 lbs. • Not for use on below grade substrates. • Deep & Accent Bases must be applied at temperatures above 50 º F. CLEAN UP & THINNING INSTRUCTIONS Clean Up: Clean up any minor spills and spatters immediately with warm soapy PRECAUTIONARY & SAFETY INFORMATION water, as well as all painting tools and airless equipment. More serious paint CAUTIONS: Avoid prolonged contact with skin, and breathing of dust, vapors spills should be contained and removed with inert absorbent material. Dispose and/or spray mists. Causes eye irritation. USE WITH ADEQUATE of contaminated absorbent, container, and unused contents in accordance with VENTILATION! Ensure fresh air entry during application and drying. If you local, state and federal regulations. experience eye water, headache or dizziness, or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriately fitted Thinning: Stir thoroughly and apply as it comes from the container. Thinning is respirator, (NIOSH approved), during and after application. Follow respirator not necessary. However, if thinning is required, you may add clean water up to manufacturer’s directions for respirator use. Avoid contact with eyes, skin and ½ pint per gallon. clothing. Use chemical safety glasses, goggles or a face shield for proper eye protection. Wash thoroughly after handling and before eating or smoking. Close container after each use. DO NOT TAKE INTERNALLY! FIRST AID: In case of skin contact, wash thoroughly with plenty of warm soapy water. For eye contact, flush with plenty of water for 15 minutes and get medical attention immediately. If you experience difficulty breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately. If swallowed, do not induce vomiting, get medical attention immediately.

KEEP OUT OF REACH OF CHILDREN!

WARRANTY & LIMITATIONS The technical information contained herein is accurate to the best of our knowledge. All warranties are excluded, whether expressed or implied, by operation of law or otherwise, including all implied warranties of merchantability or fitness for a particular purpose. Seller shall not be liable, directly or indirectly, under any circumstances for consequential, incidental, special or any other type of damages arising or resulting for any reason under the sale, handling, or use of goods sold. Seller’s liability hereunder, and buyer’s exclusive remedy hereunder, for negligence or any other reason, is expressly limited to reimbursement of the purchase price of the materials sold after proof of purchase is provided to the seller. Notice of any alleged failure or defect in the material must be given to the seller in writing by certified U.S. mail within 15 days of noticing the problem. Failure to give the required notice within the time provided constitutes a waiver of any claim. The Manufacturer is not responsible for any misrepresentation made by the Dealer.

REV 07-13

RICHARD’S PAINT MANUFACTURING COMPANY, INC. • 200 PAINT STREET • ROCKLEDGE, FL 32955 Tel: 321-636-6200 • Fax: 321-633-0866 • Toll Free: 800-432-0983 • Web Site: www.richardspaint.com