JOHNSTON COMMUNITY SCHOOL DISTRICT
WALLACE ELEMENTARY SCHOOL DESIGN DEVELOPMENT PRESENTATION
frk architects + engineers
December 12, 2016 frk architects + engineers
PROJECT DESIGN TEAM WALLACE ELEMENTARY SCHOOL JOHNSTON COMMUNITY SCHOOL DISTRICT
ARCHITECT
frk architects + engineers Project Principal: Tom Wollan, AIA Project Architect: Tim Veatch, AIA
MECHANICAL/ELECTRICAL/STRUCTURAL ENGINEER
Bluestone Engineering Mechanical Engineer: Tim Shimerdla, PE Electrical Engineer: Justin Olson, PE Structural Engineer: Ben Long, PE
CIVIL ENGINEER
Snyder and Associates Civil Engineer: Don Marner, PE
OWNER
Johnston Community School District School Board: Mark Toebben, President Marci Cordaro, Vice-President Greg Dockum Deb Henry Jill Morrill Matt Stahr Brad Ortmeier Alexis Rivett, Student Representative Nicole Hobson, Student Representative
Superintendent of Schools: Corey Lunn
Director of Operations : George Smith
2600 westown parkway, suite 340, west des moines, iowa 50266 : p 515.223.5100 f 515.223.7226 www.frk-ae.com frk architects + engineers
ARCHITECTURAL NARRATIVE DESIGN DEVELOPMENT PROPOSAL WALLACE ELEMENTARY SCHOOL JOHNSTON COMMUNITY SCHOOL DISTRICT
The existing Johnston Middle School will go through an extensive adaptive reuse construction project to become the new location for Wallace Elementary School.
The site will have minor changes to accommodate the elementary program. Bus drop-off and parking will move to the west end of the building. The west entrance will be a dedicated entrance for bussed students. The existing south drive will become the parent drop-off lane for the south entrance of the elementary school and the early childhood program. New outdoor playgrounds will be located on the northeast corner of the site for the elementary school. An early childhood playground will be located in the southwest corner of the site.
The new facility will meet the building codes that have been adopted since the Middle School was constructed. A new sprinkler system will be added to the entire building. Modifications have been made to the restrooms to meet new provisions of the ADA code for handicap accessibility. New energy efficient LED lights will replace existing lighting and the student wings will have new heating and ventilation systems.
Existing classroom wings will be entirely gutted on the interior to accommodate the new elementary program. The early childhood program will be housed in the southwest wing. The early childhood wing will feature ten studios, each with its own sink and toilet. There will be a student activity center with a reading area in the center of the studios. The early childhood area will also have both an outdoor and an indoor play area.
The kindergarten and 1st grade program will be in the next wing to the east. The kindergarten and 1st grade wing will feature ten studios, each with their own sink and toilet room. Each studio will have a moveable glass partition that will allow it to open onto a central student activity room.
The southeast and northeast building wings will be home to the 2nd and 3rd grades, and the 4th and 5th grades respectively. Each studio will have a moveable glass partition that will allow it to open onto smaller student activity areas.
Other areas of the school will receive new ceilings and finishes in the music rooms, auditorium and media center. The art department will be expanded for an elementary program with additional studio space. The administration area will have minor renovations to the west side to become principals’ offices and a reconfigured nurse’s suite. Corridors and the entrance lobby will be updated with new colors and finishes.
Exterior windows and unit heaters will be removed in the studios and replaced with aperture windows with seating areas for students. Larger windows in the student activity areas would accommodate a small group of students for performances. Each wing will be identified with a different color both on the exterior and interior for the student to easily find their way.
2600 westown parkway, suite 340, west des moines, iowa 50266 : p 515.223.5100 f 515.223.7226 www.frk-ae.com
frk architects+ engineers S TO RA G E METER/STORAGE LARGEMOTOR W A TER O UT DO O R PLAMSEAT,WINDOW INSTRUMENTAL LARGEMOTOR STOR Arts Administration TeacherStation Service RestroomRenovation PhysEd Multipurpose(Special Needs, AEA, Etc.) MediaCenter Commons Classrooms Circulation INDO OR 1- '4" AFF MUSIC RJET ONPROJ ECTI SCR EEN E VRED DOOROVERHEADNEW VESTIBULE CHILDHOOD EXG STORAGE EA RLY TOILET STOR STUDIO VESTIBULE T ROUGH CUSTOM HANDWASH STUDIO O F F IC E STUDIO PROG SPACE/ HAND NK SI STOR SPECIAL NEEDS S TO RA G E COMPU TER O F F IC E WKRM FUTURE ROOM PROJECTIONSCREEN SPACE/ ELL PROG RA M EQUIP.CUBBIE HIGH 4'-0" WHEELED O F F IC E CO OLER ATER W ELEC ELEC E DOORNEW -WAVE MICRO AROUND NKSSI E ING HUNG LI CEI HARD SURFACE BOOTH/CONFERENCE STUDIO E DOORNEW OBSERVATION VOCAL MUSIC STUDIO W/ BOTTLE W/ FILLER COOLERWATER STUDENT ACTIVITY DW DW DW REF STOR STAFF R TEACHERS E FLEX NEW MKBDW/
F MUSICSTAFF WIN DOW ONOBS ERV ATI ONE- AY W CUSTODIAN ELECWATERCOOLER W/ N PROJECTORAND TEACHINGWALL PRO GRA M PLAMSEAT,WINDOW STOR COR RID OR STUDIO SPACE BOTTLE FILLER STA TI ONS COMP UTE R VESTIBULE
1- '4" AFF DISPLAY STUDIO NEEDSLEVEL II/III w/ TIME COR RID OR EVAPORATORS SPECIAL STOR BOILER ROOM OUT LM NDOWPLAM I W STUDIO STUDIO EQUIP.CUBBIE HIGH 4'-0" WHEELED STOR SINK BUBBLER SINK COUNTERW/ HIGH 36" AF ITEHALF LI IN DOIN O R GREENWALL 1- '4" AFF SEAT, MEDIA T.O. DOORT.O. LIGHT WIN DOW 1- '4" AFF D W AT IONPARTI TI VESTIBULE FO LDIN G SEAT, FLEX PLAM STUDIO T R A I NI NG LOBBY ALT. OFFICE MAKER SPACE BOYSLOCKER RJECTORPROJ E ROOM S TO RA G E COMPUTERSTATIONS DROPBOX S TO RA G E CENTER MEDIA O F F IC E O F F IC E BOOKSHELVES VESTIBULE MECH/ELEC WORKROOM/ S TO R A G E IRCULCI ATI ON O FF GYMO FF TOILETNEW DESK PRO GRA M SPECIAL SPACE / NEEDS D USTABLEADJ BASKETBALL GOALSBASKETBALL W/ SINK ANDSINK BUBBLER W/ COUNTERHIGH 30" VESTIBULE STUDIO STUDIO HA LL AROUND NKSSI HARD SURFACE STUDIO STUDIO STUDIO HAND NK SI O F F IC E LO CKER PE ROOM GIRLS RJECTORPROJ E ANDWALL NGTEA CHI G Y M NA S IU M C O A C H' S O F F IC E RJECTORPROJ E COMP UTE R STA TI ONS COR RID OR INACTIVITYSPACE FLOORELEC BOXES STUDENT ACTIVITYSPACE ATT ONSTOPARTITI FOLDINGGLASS ACTIVITY HA LL BOTTLE FILLER WATERCOOLER W/ C O A C H' S O F F IC E BOYSLOCKER ROOM N SPACE NGSTACK I ONPARTI TI G LASS O F F IC E PE STUDIO VESTIBULE STUDIO STUDIO STUDIO SCALE: MAIN LEVEL FLOOR PLAN - COLOR MULTI-PURPOSE STUDIO HA LL ROOM ELEC (AUTISM OR N.T.S. 1" = 20'-0" N CHANGIAND C NG T ABLE ROLLSHOWERIN SPECIAL D USTABLEADJ BASKETBALL GOALSBASKETBALL NEEDS S&P) NURSE OFFICE COR RID OR C O T RO O M O F F IC E SAFE WORK UP OFRNECONFERENCE CONFERENCE CONCESSIONS ATTENDANCE STUDENT MECH ART REF AUDITORIUM COR RID OR VESTIBULE PROJECTION LOBBY STA GE W/ PENISULA W/ SINKS COUNTERSHIGH 30" D I S PL A Y RECEPTION UP W O RR K O O M S TO RA G E VESTIBULE TEACHER
O F F IC E O F F IC E REF S TO RA G E STOR KILN O UT DO O R ACTIVITY UP AREA D R E S SI N G COR RID OR 0 IH COUNTERSHIGH 30" ROOM UP W/ PENISULA W/ SINKS ELEC PRO GRA M SPACE S TO RA G E PROG SPACE IL BOYS GIRLS G IRLS ART ART KTC STORAGE STUDENT ACTIVITY RJECTORPROJ E STA TI ONS COMP UTE R SPEC IAL NEEDS STOR STUDIO BOYS NEEDSLEVEL MECH S TO RA G E II/III w/ TIME SPECIAL SPACE NGSTACK I ONPARTI TI G LASS AF ITEHALF LI STUDIO SINK BUBBLER SINK IN DOIN O R OUT W/ SINK ANDSINK BUBBLER W/ COUNTERHIGH 36" T.O. DOORT.O. LIGHT COUNTERW/ W/ SINK ANDSINK BUBBLER W/ AND LOCKERS AROUND NKSSI HARD SURFACE 0 IH COUNTERHIGH 30" 36" HIGH 36" STUDIO STUDIO STUDIO STUDIO STUDIO W/ BOTTLE W/ FILLER W/ BOTTLE W/ FILLER WATER COOLERWATER WATER COOLERWATER STUDIO STUDIO STUDIO STUDIO RJECTORPROJ E ANDWALL NGTEA CHI PRO GRA M SPACE STUDIO CAFETERIA ELEC/MECH COR RID OR STUDIO STUDIO STUDIO PRO GRA M W/ BOTTLE W/ FILLER COOLERWATER ACTIVITYSPACE ATT ONSTOPARTITI FOLDINGGLASS SINKS ANDLOCKERSSINKS HARDAROUNDSURFACE STUDIO SPACE SPACE NGSTACK I ONPARTI TI G LASS RJECTORPROJ E COR RID OR RJECTORPROJ E ANDWALL NGTEA CHI STUDENT ACTIVITY STUDIO STUDENT ACTIVITY COMPUTERSTATIONS COMP UTE R STA TI ONS STUDIO STUDIO RJECTORPROJ E STUDIO KTC RJECTORPROJ E ACTIVITYSPACE ATT ONSTOPARTITI FOLDINGGLASS STUDENT ACTIVITY WALLACE ELEMENTARY SCHOOL VESTIBULE DISHWASHING JOHNSTON COMMUNITYSCHOOL DISTRICT VESTIBULE S E R VI N G S TO RA G E O F F IC E CHAIR RECEIVING KITCHEN CUSTODIAN S TO RA G E TOILET DRY MECH FREEZER CO OLER UP JOHNSTON, IOWA CORRIDOR DROP BOX NEW OVERHEAD DOOR MECH/ELEC PROGRAM RECESSED DISPLAY MAKER PLAM BENCH CASE MEDIA SPACE / SPACE SPECIAL WORK ROOM/ NEEDS STOR PLAM WINDOW SEAT, PROG SPACE/PLAM WINDOW SEAT, STOR STORAGE 1-'4" AFF 1-'4" AFF GREEN WALL COMPUTER STATIONS SPECIAL NEEDS PLAM WINDOW SEAT, BOOK SHELVES STOR 1-'4" AFF STUDIO STUDIO STUDIO
STUDIO STOR CEILING HUNG CIRCULATION PROJECTION ELEC WATER COOLER DESK SCREEN W/ BOTTLE FILLER 4'-0" HIGH ALT. OFFICE STUDENT WHEELED EQUIP. CUBBIE CUSTOM HANDWASH 4'-0" HIGH ACTIVITY TROUGH WHEELED EQUIP. CUBBIE PROGRAM LOBBY CEILING HUNG PLAM WINDOW PROJECTOR SPACE SEAT, 1-'4" AFF PLAM WINDOW ELEC WATER SEAT, COOLER 1-'4" AFF ELEC STUDIO F STUDIO RE MEDIA MICROWAVE DW STAFF CENTER
DW COMPUTER PROJECTOR STOR STATIONS STOR
HAND SINK STOR
STUDIO STUDIO HARD SURFACE AROUND SINKS
TEACHING WALL AND PROJECTOR
1 EARLY CHILDHOOD PLAN SD2 1/16" = 1'-0"
WALLACE ELEMENTARY SCHOOL JOHNSTON COMMUNITY SCHOOL DISTRICT frk architects + engineers JOHNSTON, IOWA frk architects + engineers PROGRAM SPECIAL SPACE / NEEDS BUBBLER AND SINK W/ COUNTER HIGH 30" AND LOCKERS AND SINKS AROUND HARD SURFACE HARD STUDIO HAND SINK HAND STUDIO RECESSED PLAM BENCH PLAM RECESSED STUDIO STUDIO STUDIO 1'-4" AFF 1'-4" AT SEAT WINDOW PROJECTOR AND WALL TEACHING COMPUTER STATIONS IN ACTIVITY SPACE ACTIVITY IN BOXES FLOOR ELEC FOLDING PARTITION FOLDING ACTIVITY SPACE ACTIVITY PARTITIONS TO PARTITIONS GLASS FOLDING STUDENT ACTIVITY PROJECTOR STACK SPACE STACK FILLER BOTTLE W/ COOLER WATER CASE DISPLAY 1'-4" AFF 1'-4" AT SEAT WINDOW STUDIO RECESSED PLAM BENCH PLAM RECESSED STUDIO STUDIO STUDIO STUDIO STUDENT LOCKERSSTUDENT APPETURE WINDOW APPETURE SD3 1 1/16" = 1'-0" KINDERGARTEN / 1ST PLAN OFFICE OFFICE NURSE OFFICE C O T R O O M SAFE WORK OFRNECONFERENCE CONFERENCE ATTENDANCE NEW ENTRY NEW STUDENT CANOPY SPACE STUDENT MECH REF CORRI DOR VESTIBULE LOBBY WALLACE ELEMENTARY SCHOOL VAULT JOHNSTON COMMUNITY SCHOOL DISTRICT RECEPTION W O R K R O O M TEACHER
REF OFFICE OFFICE JOHNSTON, IOWA WARDROBE PROGRAM TALL STORAGE ELEC/MECH VESTIBULE SPACE STORAGE GIRLS BOYS PROGRAM KTC 1/2 LITE SPACE DOOR
RECESSED WATER COOLER PLAM STORAGE W/ BOTTLE FILLER COMPUTER DISPLAY CASE BENCH STATIONS COMPUTER STATIONS PLAM WINDOW SEAT PROJECTOR PLAM WINDOW SEAT AT 1'-4" AFF AT 1'-4" AFF PROJECTOR STUDIO STUDIO
OUTDOOR ACTIVITY AREA HARD SURFACE AROUND SINKS AND LOCKERS STUDIO STUDIO STUDENT TEACHING FOLDING GLASS ACTIVITY WALL AND PARTITIONS TO PROJECTOR ACTIVITY SPACE
30" HIGH COUNTER W/ SINK AND BUBBLER STUDIO STUDIO FOLDING PARTITION STACKING PLAM WINDOW SEAT SPACE AT 1'-4" AFF STORAGE
RECESSED WATER COOLER RECESSED PLAM BENCH W/ BOTTLE FILLER PLAM BENCH
STUDIO STUDIO STUDIO STUDIO
1 SECOND GRADE/THIRD GRADE PLAN SD4 1/16" = 1'-0"
WALLACE ELEMENTARY SCHOOL JOHNSTON COMMUNITY SCHOOL DISTRICT frk architects + engineers JOHNSTON, IOWA HALF LITE IN DOOR SPECIAL SPECIAL NEEDS LEVEL STUDIO PROGRAM NEEDS II/III w/ TIME STORAGE 36" HIGH SPACE OUT COUNTER W/ SINK BUBBLER
T.O. DOOR LIGHT STUDIO
PROG STOR SPACE STUDIO
STOR ART
30" HIGH COUNTERS STUDIO W/ PENISULA SINKS PROJECTOR
KILN
STUDIO HARD SURFACE AROUND SINKS STUDIO AND LOCKERS
ART
STUDIO STUDIO 36" HIGH COUNTER W/ SINK AND BUBBLER DRESSING UP ROOM STORAGE WATER COOLER STUDIO W/ BOTTLE FILLER FOLDING GLASS STUDENT PARTITIONS TO ACTIVITY SPACE ACTIVITY
COMPUTER 1 STATIONS FOURTH GRADE/ FIFTH GRADE PLAN TEACHING SD5 1/16" = 1'-0" UP WALL AND PROJECTOR PROJECTOR
WALLACE ELEMENTARY SCHOOL JOHNSTON COMMUNITY SCHOOL DISTRICT frk architects + engineers JOHNSTON, IOWA CORRIDOR 1 ART/AUTISM PLAN SD6 1/16" = 1'-0"
OVERHEAD STOR DOORS ART
VESTIBULE VESTIBULE SPECIAL 30" HIGH COUNTERS W/ PENISULA SINKS NEEDS (AUTISM OR KILN S&P) GIRLS LOCKER BOYS LOCKER ROOM ROOM
STAGE
HALL HALL PE COACH'S COACH'S PE OFFICE OFFICE HALL OFFICE OFFICE UP VESTIBULE CORRIDOR UP AUDITORIUM
UP
MULTI-PURPOSE ROOM
ADJUSTABLE BASKETBALL GOALS
NEW TOILET OFF GYM
WALLACE ELEMENTARY SCHOOL JOHNSTON COMMUNITY SCHOOL DISTRICT frk architects + engineers JOHNSTON, IOWA frk SD7 1 architects + engineers 1/16" = 1'-0" MUSIC PLAN METER/STORAGE STORAGE WATER LARGE MOTOR STOR INSTRUMENTAL INDOOR MUSIC EXG PROJECTIONEXG DOOR OVERHEAD NEW SCREEN SENSORY VESTIBULE CHILDHOOD SLIDE STORAGE TABLE EARLY VESTIBULE OFFICE STORAGE/ PRACTICE COMPUTER STORAGE FUTURE WK RM OFFICE ROOM SPACE/ ELL PROGRAM OFFICE ELEC NEW NEW DOOR BOOTH/CONFERENCE BOTTLE FILLER BOTTLE W/ COOLER WATER OBSERVATION NEW NEW DOOR VOCAL MUSIC DW REF TEACHERS FLEX WINDOW OBSERVATION ONE-WAY CORRI DOR NEW MKBD NEW CUSTODIAN W/ MUSICW/ STAFF
DISPLAY VESTIBULE CORRI DOR NEEDS LEVEL HALF LITE HALF EVAPORATORS N DOORIN II/III w/ TIME SPECIAL BOILER ROOM OUT T.O. DOOR LIGHTDOOR T.O. SINK BUBBLER SINK W/COUNTER 36" HIGH GREEN WALLGREEN MEDIA PARTITION FOLDING W WALLACE ELEMENTARY SCHOOL D FLEX BUBBLER SINKW/ COUNTER 36" HIGH TRAINING JOHNSTON COMMUNITY SCHOOL DISTRICT MAKER SPACE BOYS LOCKER ROOM STORAGE STORAGE DROP BOX JOHNSTON, IOWA OFFICE OFFICE EXPOSED GW B CLG, EXPOSED CEILING, 8'-0) AFF CEILING, PAINT PAINT
3' W IDE, TYP EXPOSED CEILING, PAINT
EXPOSED CEILING, 3' W IDE, TYP PAINT GW B CLG, 8'-0) AFF
EXPOSED CEILING, PAINT
GW B CLG, 8'-0) AFF EXPOSED CEILING, GW B CLG, PAINT 8'-0) AFF
GW B CLG, EXPOSED 3' W IDE, TYP 8'-0) AFF CEILING, PAINT 3' W IDE, TYP
N REFLECTED CEILING PLAN SCALE: N.T.S.1" = 20'-0"
WALLACE ELEMENTARY SCHOOL architects + engineers JOHNSTON COMMUNITY SCHOOL DISTRICT frk JOHNSTON, IOWA EXG PRECAST BEYOND
EXG ROOF VAULT EXG ROOF VAULT EXG ROOF VAULT BEYOND BEYOND BEYOND
EXG DOOR AND EXG ROOF EDGE W INDOW , TYP
EXG FACEBRICK LIGHT POLE
EXG BRICK SOLDIER COURSE
EL: 0" MAIN LEVEL
3 NORTH ELEVATION A-201 SCALE:1/8" = 1'-0" N.T.S.
EXG PRECAST BEYOND
EXG ROOF EDGE
EXG FACEBRICK
EXG BRICK SOLDIER COURSE
EL: 0" MAIN LEVEL ALUMINUM HM DOOR LIGHT FIXTURE, TYP STOREFRONT AND SIDELIGHT
1 NORTH ELEVATION A-201 SCALE:1/8" = 1'-0" N.T.S.
EXG SKYLIGHT BEYOND
EXG ROOF VAULT MECHANICAL SCREEN EXG ROOF EDGE BEYOND
EXG FACEBRICK
EXG BRICK SOLDIER COURSE
EL: 0" MAIN LEVEL METAL PANEL CLAD METAL PANEL CLAD METAL PANEL ALUMINUM APPETURE W INDOW APPETURE W INDOW STOREFRONT
2 NORTH ELEVATION A-201 1/8"SCALE: = 1'-0" N.T.S.
WALLACE ELEMENTARY SCHOOL architects + engineers JOHNSTON COMMUNITY SCHOOL DISTRICT frk JOHNSTON, IOWA EXG SKYLIGHT EXG ROOF VAULT EXG PRECAST BEYOND BEYOND BEYOND
LIGHT FIXTURE, TYP MECHANICAL SCREEN
EXG ROOF EDGE
EXG FACEBRICK
EXG BRICK SOLDIER COURSE
EL: 0" MAIN LEVEL
METAL PANEL CLAD HM DOOR AND ALUMINUM METAL PANEL CLAD HM DOOR AND APPETURE W INDOW SIDELIGHT STOREFRONT APPETURE W INDOW SIDELIGHT
1 EAST ELEVATION A-202 SCALE:1/8" = 1'-0" N.T.S.
EXG PRECAST BEYOND
EXG ROOF EXG METAL MECHANICAL VAULT BEYOND ROOF BEYOND SCREEN MECHANICAL SCREEN
EXG ROOF EDGE
EXG ROOF EDGE EXG FACEBRICK EXG FACEBRICK
EXG BRICK EXG BRICK SOLDIER COURSE SOLDIER COURSE
EL: 0" EL: 0" MAIN LEVEL MAIN LEVEL ALUMINUM METAL CLAD STOREFRONT APPETURE W INDOW
4 WEST ELEVATION 2 EAST ELEVATION A-202 1/8"SCALE: = 1'-0" N.T.S. A-202 SCALE:1/8" = 1'-0" N.T.S.
EXG PRECAST BEYOND
EXG ROOF VAULT BEYOND
EXG ROOF EDGE
EXG FACEBRICK
EXG BRICK SOLDIER COURSE
EL: 0" MAIN LEVEL EXG OVERHEAD DOOR HM DOOR LIGHT POLE LIGHT HM DOOR HM DOOR METAL CLAD AND FRAME FIXTURE, TYP AND FRAME AND SIDLIGHT APPETURE W INDOW
3 WEST ELEVATION A-202 1/8"SCALE: = 1'-0" N.T.S.
WALLACE ELEMENTARY SCHOOL architects + engineers JOHNSTON COMMUNITY SCHOOL DISTRICT frk JOHNSTON, IOWA EXG SKYLIGHT BEYOND
ROOF VAULT BEYOND
MECHANICAL SCREEN EXG ROOF EDGE
EXG FACEBRICK
EXG BRICK SOLDIER COURSE
EL: 0" MAIN LEVEL HM DOOR AND METAL CLAD ALUMINUM METAL PANEL METAL CLAD ALUMINUM SIDELIGHT APPETURE W INDOW STOREFRONT APPETURE W INDOW STOREFRONT
1 SOUTH ELEVATION A-203 SCALE:1/8" = 1'-0" N.T.S.
EXG PRECAST BEYOND EXG METAL ROOF EXG ROOF VAULT BEYOND
MECHANICAL SCREEN
EXG METAL ROOF EDGE
EXG BRICK SOLDIER COURSE
EXG FACEBRICK
EL: 0" MAIN LEVEL ALUMINUM ALUMINUM METAL CLAD HM DOOR AND METAL CLAD ALUMINUM METAL CLAD HM DOOR AND STEEL ENTRANCE METAL CLAD STOREFRONT STOREFRONT APPETURE W INDOW SIDELIGHT APPETURE W INDOW STOREFRONT APPETURE W INDOW SIDELIGHT CANOPY COLUMN
2 SOUTH ELEVATION A-203 SCALE:1/8" = 1'-0" N.T.S.
EXG ROOF VAULT MECHANICAL BEYOND SCREEN
LIGHT POLE EXG METAL ROOF EDGE
EXG BRICK SOLDIER COURSE
EXG FACEBRICK
EL: 0" MAIN LEVEL OVERHEAD DOOR METAL CLAD METAL CLAD ALUMINUM METAL CLAD APPETURE W INDOW APPETURE W INDOW STOREFRONT COLUMN
3 SOUTH ELEVATION A-203 SCALE:1/8" = 1'-0" N.T.S.
WALLACE ELEMENTARY SCHOOL architects + engineers JOHNSTON COMMUNITY SCHOOL DISTRICT frk JOHNSTON, IOWA EXG FACEBRICK EXG ROOF EDGE EXG FACEBRICK EXG ROOF EDGE
EXG BRICK EXG BRICK SOLDIER COURSE SOLDIER COURSE
EL: 0" EL: 0" MAIN LEVEL MAIN LEVEL HM DOOR AND ALUMINUM METAL CLAD ALUMINUM SIDELIGHT STOREFRONT APPETURE W INDOW STOREFRONT
4 SOUTH ELEVATION 1 WEST ELEVATION A-204 1/8"SCALE: = 1'-0" N.T.S. A-204 SCALE:1/8" = 1'-0" N.T.S.
EXG ROOF EDGE
EXG BRICK SOLDIER COURSE
EXG FACEBRICK
EL: 0" EL: 0" MAIN LEVEL MAIN LEVEL
METAL CLAD METAL CLAD APPETURE W INDOW APPETURE W INDOW
3 SOUTH ELEVATION 2 EAST ELEVATION A-204 SCALE:1/8" = 1'-0" N.T.S. A-204 SCALE:1/8" = 1'-0" N.T.S.
EXG ROOF VAULT
EXG ROOF VAULT
EXG FACEBRICK EXG FACEBRICK
EXG BRICK EXG BRICK SOLDIER COURSE SOLDIER COURSE
EL: 0" EL: 0" MAIN LEVEL MAIN LEVEL HM DOOR METAL CLAD AND FRAME APPETURE W INDOW
6 MEDIA CENTER EAST 5 WEST ELEVATION A-204 SCALE:1/8" = 1'-0" N.T.S. A-204 SCALE:1/8" = 1'-0" N.T.S.
WALLACE ELEMENTARY SCHOOL architects + engineers JOHNSTON COMMUNITY SCHOOL DISTRICT frk JOHNSTON, IOWA frk architects + engineers SD19 2
4" 2'-1" 1 1/2" = 1'-0" OPEN CUBBY BASE 1' - 1" VINYL BASE VINYL BACK PLAM DIVIDERPLAM
4" 3' - 2" 1' - 6" 2' - 0" ROOM (VARIES PER CLASSROOM) PER (VARIES ROOM TYPICALA IN CUBBIES WIDE 9" - 20 NOTE: '-0 '-0 '-0 '-0 3' - 0" 3' - 0" 3' - 0" 3' - 0" 3' - 0" SD19 1 1/2" = 1'-0" PRE-K LOCKERS WALLACE ELEMENTARY SCHOOL SD19 2 JOHNSTON COMMUNITY SCHOOL DISTRICT JOHNSTON, IOWA 7' - 0" frk
4" 3' - 4" 10" 2' - 6" architects + engineers SD17 1 1/2" = 1'-0" LOCKER ELEVATION 1' - 0" TYP WALLACE ELEMENTARY SCHOOL JOHNSTON COMMUNITY SCHOOL DISTRICT JOHNSTON, IOWA ADJ SHELVES ADJ VINYL BASE VINYL BAY LOCKER PLAM HOOK SHELF PLAM W/ CABINETS UPPER PLAM
Johnston Middle School Adaptive Reuse Mechanical / Electrical / Technology Design Development Narrative November 21, 2016
DIVISION 21 – Fire Protection Systems
A. 21 05 00 – Fire Protection Common Work Results
• All work shall conform to the most current version of all applicable codes and standards or the version adopted by the City of Johnston, State of Iowa and any other authority having jurisdiction. o International Fire Protection Code o NFPA – National Fire Protection Association o State and City Codes
• Design sprinkler system per NFPA 13 using performance requirements and design criteria required.
• Sprinkler system design shall be approved by Authority Having Jurisdiction (AHJ).
• Sprinkler system shall be hydraulically designed and have a density of at least that required by the hazard rating of the area protected.
B. 21 13 00 – Sprinkler System
• A new 6” fire protection water service with backflow preventer will be installed. o Static and residual water pressure will be confirmed with the water/fire department which may alter the size of the incoming service.
• The building will be protected by wet pipe fire protection system.
• Old ceilings will be removed and new ceilings will be installed in all areas to accommodate new sprinkler piping in the existing building.
• Install alarm devices in piping systems. A flow alarm switch shall be provided in the sprinkler riser and shall be wired into the fire alarm system.
• Wet-pipe sprinkler, above grade: Black steel, schedule 40. Threaded for 2” and smaller. Grooved for 2-1/2” and larger. CPVC will be allowed as an alternate piping material, at this time.
• Sprinkler heads within the building will be automatic-type with heat-responsive element and escutcheon. o Concealed type sprinkler heads will be used in all of the occupied areas of the building. o In unoccupied areas or storage rooms, upright or semi-recessed sprinkler heads will be used.
• Sprinkler temperatures required will be based on space usage and location.
• Install sprinkler piping with drains for complete system drainage.
• Inspector test station: Combination test and drain assembly. Angled design with tamper resistant test orifice, sight glass and identification plate. Bronze body, brass stem, impregnated Teflon seat, chrome coated brass ball, locking kit and steel handle allowing for positive stops at the test and drain positions. Tapped port in the valve body for relief valve and pressure gauge.
9119 Northpark Drive | Johnston, IA 50131 | P 515.727.0700 | F 515.727.0777 | www.bluestonemep.com
• Hose stations will be installed at the end of the stage as required by NFPA 13 for stages larger than 1,000 SF.
• Dry pendent sprinklers will be installed in freezers and coolers.
• A new fire department connection will be installed on the wall outside of the new water entrance room. It will have four (4) connections per Johnston Fire Department.
• The gymnasiums will be designed as an ordinary two hazard, per Johnston Fire Department.
DIVISION 22 – Plumbing System
A. 22 05 00 – Plumbing Common Work Results
• All work shall conform to the most current version of all applicable codes and standards or the version adopted by the City of Johnston, State of Iowa and any other AHJ. o International Building Code o International Mechanical Code o Uniform Plumbing Code o State and City Codes
B. 22 05 23 – Plumbing Valves
• Shutoff valves will be installed in the following locations : o Building water service entrance inside the building o All major branches tapping off of domestic water piping mains o Each restroom group
• In addition to the locations listed above, each plumbing fixture will have quarter turn angle stop shutoff valves.
• All valves will have valve tags permanently affixed for inventory and identification purposes. A list of valve numbers with location and service information will be provided to the owner upon project completion.
C. 22 11 00 – Plumbing Piping
• Contractor shall include all work required to extend utilities as required for new work.
• Utility work 5’-0” from outside of building is by others, unless shown otherwise.
• The building shall be served by the existing 4” domestic cold water service. o A new domestic water meter/BFP will be installed utilizing the existing 4” domestic water entrance. • Cold water piping from the new water entrance will backfeed the existing 3” cold water mains serving the existing building.
• Domestic hot water piping will be modified and extended as required. The existing main hot water heating plant will remain.
• New piping installed in the building will utilize multiple material types based on the system it is serving: o Domestic cold water, above grade: ° Type L copper, lead-free solder and wrought copper fittings. o Domestic hot water, above grade: ° Type L copper, lead-free solder and wrought copper fittings.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 2 of 17
o Sanitary/Vent/Storm, above grade ° Cast iron pipe, bell and spigot or no-hub o Sanitary/Vent/Storm, below grade ° Cast iron pipe, bell and spigot or no-hub ° Schedule 40 PVC. o Natural Gas, above grade, less than 2” ° Black steel, Schedule 40. Threaded or welded. ° All natural gas piping concealed shall be welded. o Equipment drains ° DWV copper with lead free solder and wrought copper fittings. • New piping installed in the building will utilize multiple insulation thicknesses based on the system it is serving: o Domestic cold water, above grade: ° 1-1/4” or less:1” fiberglass ° 1-1/2” or greater: 1” fiberglass o Domestic hot water, above grade: ° 1-1/4” or less:1” fiberglass ° 1-1/2” or greater: 1-1/2” fiberglass o Sanitary/Vent/Storm, above grade ° 1” fiberglass on storm piping ° 1” fiberglass on vent risers within 10’ of vent-through roof connection. o Natural Gas, above grade, less than 2” ° none o Equipment drains ° 1” fiberglass
D. 22 40 00 – Plumbing Fixtures and Equipment Installation
• Plumbing fixtures will be installed per the new architectural floor plans. o Water Closets: Wall mounted with 1.28 gallons per flush battery powered sensor operated flush valves. o Urinals: Wall mounted with 0.5 gallon per flush battery powered sensor operated flush valves. o Lavatories: Wall or countertop mounted with battery powered sensor operated flush valves. All public lavatories shall have point-of-use thermostatic mixing valve on hot water. o Sinks: 18 gauge stainless steel. Faucet will vary by sink location and usage. o Mop Basins: 24”x24” floor mounted molded stone mop basin with wall mounted faucet with hose connection, pail hook, and wall brace. o Shower: Valve and drain. Will work with Architect to see if this needs to be a pre- manufactured unit.
DIVISION 23 – HVAC System
A. 23 05 00 – HVAC Common Work Results
• All work shall conform to the most current version of all applicable codes and standards or the version adopted by the City of Johnston, State of Iowa and any other authority having jurisdiction. o International Building Code o International Mechanical Code o International Energy Conservation Code o State and City Codes
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 3 of 17
• Mechanical Design Criteria o Outdoor Conditions • Summer: 94°F db / 77°F wb • Winter: -10°F db o Indoor Conditions Room Type Summer Conditions Winter Conditions
Offices, Conference, Corridors 74-76°F / 30-60% RH 70-72°F
Studios 74-76°F / 30-60% RH 70-72°F
Breakrooms 74-76°F / 30-60% RH 70-72°F
Mechanical / Electrical Rooms 75-78°F / 30-60% RH 70-72°F
Vestibules No Cooling 60°F (Heating Only)
• LEED o Currently, LEED certification is not being pursued as a design option as part of this renovation.
• HVAC System (Complete renovation areas): o Two variations to a Variable Refrigerant Flow (VRF) system are being considered for conditioning of the renovation areas. o Variable Refrigerant Flow, AIR-COOLED , heating/cooling system with packaged gas- fired, DX cooling Dedicated Outdoor Air System (DOAS) unit for studio pods. ° The VRF system will be a heat recovery system so each heat pump would be able to provide either heating or cooling. ° Each space/zone will have an indoor heat pump unit for individual room temperature control. ° The indoor units will work within the architectural features for the best selection, but 2x2 ceiling-mounted, cassette-type units will be utilized. ° Refrigerant piping will be routed from multiple indoor units, combined and routed to a single, large outdoor unit ° The outdoor units will be located on the roof with one bank for each studio pod. ° Supplemental heating (i.e. hot water finned tube radiation), served from the existing hot water plant, will be utilized for very cold conditions when the VRF heating cannot keep up. ° Ventilation for the studio pods and potentially, some adjacent spaces, resident rooms and some common spaces shall be provided via DOAS units. One DOAS unit should be anticipated for each studio pod. The amount of ventilation shall meet code required minimum requirements. • HVAC System (Minor renovation areas): o The existing heat pump systems (either boiler/cooling tower or geothermal) will be maintained in areas where minor renovation is taking place. ° Areas like the west side of Administration, Special Needs, Corridors, and Art. • See HVAC scope plan in appendix for areas of work.
• HYDRONIC ALTERNATE : o As an alternate, the existing hot water boilers will be converted to high-efficient, condensing hot water boilers.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 4 of 17
B. 23 05 13 – Motors
• All new motors installed in new air handling equipment will be open drip proof premium efficiency motors.
• Motors intended for use with variable frequency drives will be rated for such use.
C. 23 05 29 – Pipe Hangers and Supports
• All piping will be supported from the structure.
D. 23 05 48 – Vibration and Expansion Control
• The following equipment will have vibration isolation and expansion control devices installed to mitigate vibration and sound transmission throughout the building: o Energy Recovery units o Ductwork at ERV connections. o Ceiling suspended fans and equipment
E. 23 05 53 – Mechanical Identification
• All new piping will have labels and flow arrows installed to designate system type and flow direction.
• All new mechanical equipment will have permanent labels affixed. Equipment will include: o Air handlers o VFD’s o Thermostats and controls
F. 23 05 93 – Cleaning and Testing • After construction is complete, all newly installed ductwork and piping systems will be pressure tested and tested for leakage.
• All plumbing systems will be cleaned and flushed of debris prior to system startup .
G. 23 05 94 – Testing Adjusting and Balancing • Upon project completion, all duct systems and piping systems will be balanced to the airflow and water flowrates as noted in the construction documents to verify that all systems are functioning as specified.
H. 23 07 13 – Ductwork Insulation • Ductwork insulation requirements shall meet International Energy Conservation Code.
• Ventilation Air, Supply air: o 1-1/2” fiberglass wrap
• Return and exhaust air back to DOAS: o 1-1/2” fiberglass wrap
• General Exhaust air: o 1-1/2” fiberglass wrap within 15’ of fan or unit
I. 23 07 19 – Piping Insulation • Piping insulation requirements shall meet International Energy Conservation Code.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 5 of 17
• Refrigerant lines: o 1-1/2” fiberglass wrap.
• Hot water heating: o 1-1/2” fiberglass wrap.
J. 23 08 00 – Commissioning of HVAC • The following systems and equipment will be fully commissioned as part of the building renovation to verify proper operation and functionality. o Energy Recovery units o Fans o Terminal units o Vibration isolation equipment o Balancing valves o Cooling and heating coils o Control dampers
• Upon project completion, a final commissioning report will be compiled and delivered to the owner.
K. 23 09 00 – Temperature Controls • A new building DDC system shall be installed to incorporate the new VRF system, as well as integrate the existing mechanical components of the building.
• The new system will include the following: o Basis of Design: Johnson Controls. Woodman Controls may be an alternate. o New dedicated controls PC workstation for building maintenance staff. o Computer workstation will have floor plan graphics showing all HVAC zones and individual pieces of equipment with monitored control points. Equipment graphics with user definable control points will be as follows: ° Energy Recovery units ° VRF control integration ° Exhaust fans ° MDF/IDF room temperature monitoring ° Equipment with packaged controls ° Domestic hot water temperature monitoring ° Terminal heating and cooling equipment o Final DDC points and extent of controls will be refined as the design process continues.
L. 23 21 13 – Hydronic Piping • Heating hot water piping will be extended to supplemental heating terminal units. Hot water supply and return piping will meet the requirements listed in the piping application schedule.
M. 23 23 00 – Refrigerant Piping • Refrigerant piping will be required for a new VRF system. Refrigerant piping will meet the requirements listed in the piping application schedule.
N. 23 29 23 – Variable Frequency Drives • Variable frequency drives will be installed on the following equipment: o Energy Recovery Units
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 6 of 17
O. 23 31 13 – Metal Ductwork • New ductwork will meet the construction and insulation requirements for the project.
P. 23 33 00 – Ductwork Accessories • Fire dampers / fire smoke dampers will be installed in all ductwork as required based on the final code review plans provided by the architect.
• All air inlets and outlets will be provided with airflow control dampers as required to allow for proper system adjusting and balancing.
• Energy recovery units will include blowout doors, as required, to prevent duct over-pressurization.
Q. 23 34 25 – HVAC Power Ventilators • General exhaust fans will be roof mounted mushroom type exhaust fans.
• New exhaust fans will be located in areas like the new teacher’s lounge and art room.
• Replacement of existing exhaust fans for the toilet room modifications will be investigated.
• All fans with airflow greater than 500 CFM will be belt driven and will be provided with a fan speed controller.
• Roof curbs will be provided by the mechanical contractor.
R. 23 37 00 – Air Inlets and Outlets • Supply and return diffusers will be 24”x24” square plaque type diffusers.
• Linear slot diffusers will be utilized in perimeter areas and areas with glazing.
• Exhaust grilles will be a combination of double deflection grilles and square plaque diffusers based on usage and location.
S. 23 52 16 – Heating Water Condensing Boilers • As an alternate, the existing hot water boilers will be modified to condensing hot water boilers.
T. 23 71 00 – Energy Recovery Unit (DOAS) • Ventilation for the studio pods and some common spaces shall be provided via DOAS units.
• Units shall be outdoor, roof-mounted equipment.
• Unit components will be as follows: o Exhaust fan o Filter section(s) o Electric preheat coil for wheel frost protection (or other wheel stop/jog approach) o Energy recovery wheel o DX cooling components including hot gas reheat coil o Gas-fired heat exchanger o Supply fan o Dampers and Controls
• Additional features shall include vibration isolation curb.
U. 23 81 30 – Variable Refrigerant Flow Systems • Multiple, packaged VRF systems will be utilized to condition the studio pods.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 7 of 17
• Packaged indoor fan coil units will consist of a fan, heating/cooling DX coil, housing, condensate drain, etc. o Predominantly will use cassette-type units that are flush to the ceiling.
• Air-cooled: Packaged, outdoor units will be heat pump units with heat recovery. o Units will be roof mounted with copper tubing, aluminum fins, fan, scroll compressors and associated refrigeration components. o Units will be located in heated “doghouses”, with gas-fired unit heaters to maintain temp.
• VRF systems shall contain an intelligent controller for integration into the building DDC system.
DIVISION 26 – Electrical Systems
A. 26 05 00 – Electrical Common Work Results
• All work shall conform to the most current version of all applicable codes and standards or the version adopted by the City of Johnston, State of Iowa and any other AHJ. o National Electrical Code (NEC) o International Building Code o International Fire Code o International Energy Conservation Code o Other applicable Codes for the City of Johnston and State of Iowa
• Submittals will be required for all major equipment and systems (e.g. lighting, lighting control, electrical gear, etc.).
• All penetrations of fire rated assemblies, both new and existing, shall be fire stopped using UL approved method. Refer to architectural code plan. The contractor will need to investigate the extent of work prior to bidding.
• All non-rated penetrations, both new and existing, shall be caulked to limit sound and vapor transmission. The contractor will need to investigate the extent of work prior to bidding.
B. 26 05 02 – Demolition
• The existing two (2) electrical services and associated switchboards (1600 amps and 1200 amps) will remain and be reused.
• Complete electrical demolition will occur in four (4) main studio pods (west, central, east and north). Selective electrical demolition will occur in the remaining areas, including some site electrical demolition.
• Refer to the sections below for additional demolition information by system.
C. 26 05 19 – Electrical Power Conductors and Cables
• All new panel feeder conductors will be aluminum. All branch circuit conductors and feeders to mechanical equipment will be copper.
• All conductors will have 90°C rated insulation.
• MC Cable will NOT be allowed on the project.
• Branch circuit conductors will be #12 AWG minimum with sizing increased as required to maintain allowable branch circuit voltage drop of 3%.
• Common neutrals will not be allowed for branch circuits.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 8 of 17
• Life safety circuit conductors will be installed in separate raceways from non-emergency wiring, per NEC requirements.
D. 26 05 23 – Control Cables
• Control cable sizes will match system requirements.
• Shielded cable will be used where required.
• Control cables will be installed in raceway.
E. 26 05 26 – Grounding
• The existing electrical grounding electrode system at each service entrance switchboard will be reviewed by the contractor and brought up to current code, if needed.
• A technology isolated grounding system, including isolated ground bar and bonding conductor, will be added to the existing MDF and IDF room and any new IDF rooms. Grounding/bonding systems in IDF/MDF rooms will conform to ANSI/TIA/EIA-J-STD-607-A requirements.
• Insulated equipment grounding conductor will be installed with all feeders and branch circuits and will be terminated using UL listed components.
• All equipment will be grounded per NEC.
• Lightning protection is not currently installed on the building and will not be added to the building.
F. 26 05 29 – Hangers and Supports
• Conduits, cables, electrical boxes and electrical equipment will be supported in accordance with NEC.
G. 26 05 33 – Raceways and Boxes
• There will be no re-use of existing branch circuit raceway in the studio pods. Outside the studio pods, existing raceways properly supported and installed may be reused for new circuiting. It was noted during field take-off that some of the existing conduit is routed tight to the ceiling deck, which is now a code violation. None of these conduits can be re-used. In addition, conduit may not be relocated. • All wiring and low voltage cabling shall be installed in raceways per the conduit installation schedule below.
• Conduit installation schedule: o Underground: Schedule 40 PVC. Exposed conduits shall transition to galvanized RMC prior to sweep through floor slab. o Directional Boring: HDPE o Exposed Outdoor Locations: Galvanized RMC or EMT with rain tight fittings, unless subject to damage. o Concealed in Concrete and Block Walls: EMT o Wet Interior Locations: EMT with rain tight fittings, unless subject to damage where galvanized RMC will be used. o Concealed Dry Interior Locations: EMT o Exposed Dry Interior Locations: EMT o Motor and Equipment Connections: LFMC, maximum 6’ long o Luminaire Connections: Minimum 3/8” diameter whip, maximum 6’ long
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 9 of 17
• In areas with existing block walls, metal surface mounted raceway will be provided (Wiremold 700 series for power only, Wiremold 4000 series for power/data applications).
• Outlet boxes will be galvanized steel with stamped knockouts. Provide double-gang back boxes with single gang openings for all technology outlets.
• Cast back boxes will be used in wet locations with cast aluminum NEMA 3R while-in-use covers.
• Floor boxes will be used in the studio pods activity areas. Floor boxes will be reach-in type and allow for both power and technology outlets.
H. 26 05 36 – Cable Tray • Ladder type cable tray will be installed in the MDF and IDF closets directly above data racks with conduit sleeves in walls to extend cabling outside of rooms. • Cable entrance/exit accessories will be utilized to alleviate stress on cables. • J-hooks will be used where cable quantities are minimal.
I. 26 05 53 – Identification • All new and existing power distribution equipment (switchboard, distribution panels, panelboards, VFD, disconnect switches, equipment enclosures, etc.) will have a new, engraved nameplate indicating panel name, voltage and feeder source. • Switchboard and distribution panels will also have engraved labels for branch circuit breakers indicating load served. • Panelboards will a have typed circuit directory inside panel door. • Manual starters will have a printed label that indicates load served, voltage and circuit number. • Junction boxes will have a hand written label indicating source, circuit(s) and voltage. • Generic arc flash warning labels will be provided on all power distribution equipment. An arc flash study is not required as part of this project. • Fire alarm devices will have computer printed labels indicating device loop and address. • Receptacles will have a printed label indicating panel name and circuit number. • Wire color to match existing color scheme.
• Identification of each phase conductor will be by color coded insulation for conductors up to #6 AWG and colored tape banding for conductors larger than #6 AWG.
• Branch circuit conductors will be tagged with circuit numbers in junction boxes, wire ways, and panelboards for ease of maintenance and in the future.
• New identification plaques will be provided at both existing service entrance switchboard indicating that the building is served by more than one electrical service and indicate the location of the other service, per NEC requirements.
J. 26 08 00 – Commissioning of Electrical Systems • The Contractor will participate in the commissioning of the following electrical systems: a. Lighting Controls b. Modular Dimming Controls c. VFD d. Emergency lighting, including testing the existing generator and ATS to confirm proper functioning of the new emergency devices.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 10 of 17
K. 26 09 36 – Modular Dimming Controls • Basis of design will be ETC Unison. • A twelve (12) circuit standalone dimming panel is planned for the new auditorium house lights.
L. 26 09 43 – Digital Lighting Controls • Basis of design will be the Wattstopper DLM with Acuity nLight as an approved equal. • This new lighting control system will control all areas of the building, except for the existing gymnasium and site luminaires. • The use of tunable white luminaires (~3000K – 5000K with DMX style controls) will be provided in special needs areas. • The control systems will be a distributed intelligence control system, meaning there are not centralized lighting control panels. • Each room controller will have a network bridge. The network bridges will be connected to a segment manager. The segment manager will contain an embedded web browser as well as system astronomical clock and time-of-day clock. • Monitoring and programming of the entire lighting control system and device (e.g. occupancy sensor, photosensor, etc.) will be possible from any computer with internet access and the appropriate login credentials. • Occupancy sensors will be provided in the spaces listed below (type). The sensors will be low voltage type, ceiling or corner mount and designed for easy integration into the lighting control system. For small rooms, the occupancy sensor will be integrated into the low voltage wall switch. o Studios (dual tech) o Music (dual tech) o Art (dual tech) o Large storage (ultrasonic) o Small storage (infrared) o Small restroom (infrared) o Large restroom (ultrasonic) o Computer lab (dual tech) o Private office (dual tech) o Open office (dual tech) o Special needs (dual tech) o Break room (infrared) o Teacher work room (infrared) o Corridor (ultrasonic; after hours only) o Janitor’s closet (infrared)
• Time of day automatic sweep will be used in lieu of occupancy sensors in the spaces listed below for safety reasons. o Media center o Indoor large motor o Auditorium o Cafeteria/Servery o Corridor o Locker rooms o Kitchen
• Mechanical, electrical and technology rooms will be manual switching only for safety and will not be connected to the digital lighting control system.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 11 of 17
• Photo sensors will be installed in all areas containing more than two (2) luminaires and with exterior windows, skylights or clerestory windows. The photo sensors will be designed for easy integration into the lighting control system. • 0-10 VDC dimming controls will be provided in the spaces listed below o Studios o Conference rooms o Daylight harvesting areas (except corridors) o Auditorium o Special needs studios o Media center
• Manual lighting controls will be provided in all spaces in the form of low voltage walls stations, except electrical and mechanical rooms which will use standard wall switches. In areas with dimmable luminaires, manual dimming will be provided by the wall station(s) in that space. In each studio, a scene station with on/off control and manual raise/lower will be provided. • A factory technician will conduct a pre-installation meeting with the contractor, perform startup and initial system programming upon completion of the installation and provide owner training.
K. 26 22 00 – Transformers • Basis of design: General Electric QL series. • Interior transformers to be high efficiency dry type with aluminum windings meeting DOE 2016 requirements. • A new 75 kVA transformer will be provided in each of the four (4) studio pods.
L. 26 24 16 – Panelboards • Basis of design: General Electric A-Series style with bolt on breakers. • A 250 amp, 480/277 volt MLO panelboard will be provided in each of the four (4) studio pods. • A 225 amp, 208/120 volt MCB panelboard will be provided in each of the four (4) studio pods.
M. 26 27 02 – Equipment Wiring • Disconnect all mechanical equipment and associated starter/disconnect in areas indicated in mechanical demolition narrative above. • Only under condensing boiler alternate bid: o Electrical connections and associated starters and disconnects serving the existing three (3) boilers and associated pumps will be demolished. o New electrical connections will be installed for the new boilers and pumps. VFD will be for the pumps and will be furnished by M.C. and installed by E.C.
• Underground-source geothermal VRF option, provide 480 volt, 3-phase circuits to pump motors serving loop. • Dedicated 480 volt, 3-phase circuits will be provided to each of the four (4) VRF condensing units and one (1) DOAS on the roof in each of the four (4) studio pods. • 208 volt, 1-phase circuits will be shared between the VRF cassettes throughout each pod.
N. 26 27 26 – Wiring Devices
• All wiring devices will be heavy-duty specification grade. Basis of design is Hubbell HBL5362 for receptacles and Hubbell HBL122X for switches.
• GFCI receptacles will be installed in locations dictated by code.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 12 of 17
• Branch circuit connections to wiring devices will be via a pigtail to maintain circuit integrity if/when the device is removed. • Devices will be circuited to allow additional receptacles to be connected to the circuit. Maximum of eight (8) receptacles will be connected on a 20 Amp, 120 Volt circuit. Assume two (2) 120 volt receptacle circuits per studio.
O. 26 27 28 – Disconnect Switches • Heavy duty type disconnect switches will be provided for all mechanical and plumbing equipment that does have a factory mounted local disconnect switch. Fusible disconnects will be used when needed for proper overcurrent protection.
• Basis of design: General Electric TH series.
P. 26 28 13 – Motor Controllers • Manual switches for fractional HP loads will be non-reversing, 20 amp rated toggle type, with suitable NEMA enclosure and pilot light. • Combination starters will be provided when needed for 1 HP motor loads and greater.
Q. 26 32 00 – Generator • The existing Cummins 35 kW, 480 volt diesel generator and power distribution equipment will continue to serve existing and new life safety loads.
R. 26 36 00 – Transfer Switches • The existing Cummins 60 amps automatic transfer switch will serve the existing and new life safety loads.
S. 26 51 13– Interior Lighting • The existing luminaires and associated circuiting will be demolished in all areas of the building, except for the gymnasium. • The allowable lighting power density is based on the 2012 IECC with a nominal density level of 0.99 W/ft 2 using the building area method and the ‘reduced light power density’ compliance path of 2012 IECC. • LED technology will be used as the primary source for illumination with a CCT of 4000K and a CRI of 80+. • The use of tunable white luminaires (~3000K – 5000K with DMX style controls) will be provided in the special needs studios. • Fixture Selections: (Refer to electrical Appendix for cut sheets of light fixtures and plans for locations and types used) o Studio – 40 foot-candles (fc) o Student Activity Areas (in pods) – 40 fc o Special Needs – 40 fc o Media Center – 30 fc (general), 50 fc (reading areas), 50 fc (lending desk) o Art – 50 fc o Music – 50 fc o Storage – 20 fc o Restroom – 20 fc o Private Office – 40 fc o Open Office – 40 fc o Kitchen – 50 fc o Corridor – 20 fc o Auditorium – 30 fc
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 13 of 17
o Locker Room – 30 fc o Indoor Large Motor – 30 fc o Teacher Work Room – 50 fc o Teacher Break Room – 30 fc o Dining – 30 fc o Servery – 50 fc
T. 26 52 00 – Emergency Lighting • Life safety lighting will be designed to code mandated levels. • Select luminaires will be used for life safety lighting and will be powered by the generator. In areas outside the corridors that require life safety lighting (rooms with >50 occupants) a fixture type emergency transfer device (Bodine GTD or equal) will be specified. • Exit lights will be die-cast aluminum body LED-type with red letters. Emergency power will come from the existing emergency generator.
U. 26 56 29 – Site Lighting • The two (2) existing pole lights west of the building will be demolished. All building mount and canopy mount exterior lights will also be demolished • New LED wall packs will be installed at the existing luminaire locations and near all exterior doors. • New LED wall packs will be installed for the outdoor play areas. • Three (3) new LED pole lights will be installed for the new bus parking area. Poles will be 30’ tall tampered (similar to existing) with an LED head.
DIVISION 27 – Communications
A. 27 05 13 – Communications Common Work Results
• Technology infrastructure will be designed to comply with relevant EIA/TIA.
• Existing cabling solution includes coax and copper, and fiber optic services to the facility. General scope of work includes termination for voice and data, horizontal cabling to work area, faceplates, RJ-45 jacks, fiber and copper patch cords in the equipment cabinets/racks and work areas. Reuse existing equipment cabinets/racks.
• Network hardware, switches, hubs, phone equipment head end and handsets shall be provided by the Owner. • In general, cabling will be run above the ceiling in existing cable tray or J-hooks provided by the Electrical Contractor. • A VoIP phone system for the general office areas. A digital phone system will be used for the classrooms. Phone systems provided by the owner. Analog phone lines will be provided for the fire alarm panel and other devices/systems as required.
B. 27 08 00 – Warranty of Structured Cabling
• Provide a complete end-to-end Basis of Design Panduit TX6A CAT6A cabling solution with a systems assurance warranty.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 14 of 17
C. 27 08 10 – Acceptance of Communications Fiber Cabling • All fiber optic cabling shall be tested end-to-end.
D. 27 08 20 – Acceptance of Communications Copper Cabling • All copper cabling shall be tested end-to-end.
E. 27 11 00 - Communications Rooms Fittings • MDF: In general, the existing MDF will re-use two (2) existing 19” 2-post racks will be installed in the MDF. Re-use existing ladder rack within the room. Re-use the existing Telecommunications Ground Bar (TGB). Grounding for all racks and cable tray to the TGB. • IDF: In general, the existing IDF will re-use one (1) existing 19” 2-post racks in the IDF. Re-use existing ladder rack within the room. Re-use the existing Telecommunications Ground Bar (TGB). Grounding for all racks and cable tray to the TGB. The office area, existing IDF will re- use one (1) existing 19” wall rack in the IDF. Re-use and provide ladder rack within the room. Re-use the existing Telecommunications Ground Bar (TGB). Grounding for all racks and cable tray to the TGB.
F. 27 13 00 – Communications Backbone Cabling • New 1x12 strand MM fiber optic cable (OM4) to IDF. New fiber optic patch panel to new rack system. LC connectors shall be provided. Test all backbone fiber optic cable to insure integrity. • Re-use the existing copper backbone to the IDF’s.
G. 27 15 00 – Communications Horizontal Cabling • New Panduit TX6A CAT6A horizontal cabling will be installed throughout the building. • Wireless shall be 100% coverage for the facility. Wireless access point equipment shall be by the Owner. Two (2) Panduit TX6A CAT6 cabling is included per WAP and shall be homerun from the nearest IDF closet. Power over Ethernet switches shall be provided by the owner. Access points shall be located on 35’ on centers. The owner shall conduct a wireless survey when construction is completed to verify coverage. The owner will be responsible for any other additional locations. E.C. shall install wireless access points for the project • Panduit TX6A CAT6 cabling shall be homerun back to nearest closet. Provide CAT6A for all Classrooms, Offices and work areas. The offices and work areas to have (1-voice and 1-data). Classrooms to have (6-data and 1-voice/wall phone). Provide TX6A horizontal cabling back to the nearest IDF for (47) cameras.
H. 27 30 00 – Intercom System • Provide a complete audio-video entry security intercom system. Basis of Design is the Aiphone “IX” Series”. Intercom master door station shall be located at MDF. Intercom sub master stations to be located at the main administration desks. Provide intercom door/camera stations with electric strikes at the main entrances into the facility. Cabling shall be CAT6 cable that is homerun back to the master station. System to include the mobile app for cell phones and tablets.
I. 27 41 33 – Audio Video Systems • Empty conduit pathways and junction boxes will be installed for rough-in of AV equipment in classrooms. Rough-ins will include overhead projector mounts, conduit and boxes between projector and head of the room, and miscellaneous rough-ins for AV controls where specifically requested by the owner. • Rough-ins will fly above ceiling for AV speaker system.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 15 of 17
• Rough-ins will include conduits and boxes for wall mounted controls and AV connectivity inputs for built-in ceiling projector. • Gymnasium AV System, Student Activity A/V System, and Classroom AV System – A/V equipment to be provided by owner and installed by A/V contractor. Rough-in to be provided/installed by E.C. • Auditorium – Provide new amplifiers and speakers for presentation/audio quality.
J. 27 41 33 – Master Antenna Television System • Existing CATV service at the site. New RG-11 coax backbone and RG-6 horizontal cabling to new TV end points. Provide one (1) RG-6 coax cable to all new classrooms. Re-use existing distributed amplifier. Existing amplifier to remain in the IDF near the café.
K. 27 53 13 – Bell- Paging - Clock System • Reuse existing Bell, Paging, and Clock system headend. Provide a new digital clock and speaker for each classrooms and student activity areas. Provide a two-face digital clock and speakers in the corridor. Provide 110V power, clock wiring and speaker wire at these devices. These devices to tie into the existing Telcor headend located in the Mezzanine.
L. 27 53 19 – Internal Cellular Paging and Antenna System • Provide and install new antennas, cabling, and headend for a complete operable 900 MHz system. Main headend equipment to be located in the MDF with remote equipment located in the IDF’s. • Single mode fiber optic cabling shall be the backbone cabling between the main and remote headend equipment. • Basis of Design is the Commscope Andrew System. Approved manufacturer is Corning.
DIVISION 28 – Electronic Safety and Security
A. 28 13 00 and 28 23 00 – CCTV and Security Systems
• Reuse existing access control system headend and software. Provide additional card readers, door position switches, and request to exits on the main entrances. Provide door contacts on all exterior doors. E.C. shall provide rough-in. • New CCTV cameras shall consist of (47) 1-mega pixel cameras. Basis of design: Axis. • Re-use existing network video recorder will be located at MDF. Existing ONSSI software to be reused.
B. 28 31 00 – Fire Alarm
• The existing Simplex 4100U fire alarm system will be reused and expanded. Voice capabilities will be added to the existing main fire alarm panel. • Existing smoke detection added during the 2006 addition and renovation will be removed and be reused. These are found primarily the central corridors, kitchen, servery and dining areas. • Smoke detection will be installed in all corridors, pod activity areas, and normally unoccupied spaces per Iowa Administrative Code 661, Chapter 201. Heat detectors will be installed in areas where smoke detectors are not suitable. • Duct type smoke detection for mechanical unit shutdown or smoke damper closure will be installed per building code. A sampling tube type duct detector in both the supply and return ducts will be provided for all four (4) DOAS units on the roofs.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 16 of 17
• Manual pull stations with tamper resistant covers will be provided at all exterior doors and as needed within the path of egress to maintain the 200’ maximum distance between pull stations. • Existing horn and horn/strobe devices will be removed throughout the building. The dining and servery areas speakers and speaker /strobe will remain and be rerouted to the new voice annunciation panel. • The existing voice command center located in the IDF closet in the dining area will be removed. • Voice annunciation will be provided via new fire alarm ceiling speakers through the building. Wire guards will be provided in areas like the gymnasium. Voice intelligibility will be required in the auditorium, cafeteria, gymnasium, corridors, lobbies, media center, open offices, locker rooms and music rooms. These speakers will be separate from the paging system speakers. • Fire alarm strobes will be provided in all normally occupied spaces, except private offices, per ADA requirements. • Tamper and flow switches associated with the new fire protection system will be connected to the fire alarm system via monitor modules. • A weatherproof horn/strobe will be installed above the exterior fire department connection and shall only activate upon water flow. • A voice command center with handheld mic will be installed in the west vestibule.
Bluestone | JCSD Middle School Renovation MEPT DD Narrative Page 17 of 17
APPENDIX
LIGHT FIXTURE CUTSHETS
Catalog Number
Notes FEATURES & SPECIFICATIONS INTENDED USE — Provides a minimum of 90 minutes of illumination for the rated wattage upon loss of AC power. Type Ideal for applications requiring attractive unit equipment with quick installation. Certain airborne contami- nants can diminish integrity of acrylic and/or polycarbonate. Click here for Acrylic-Polycarbonate Compatibility table for suitable uses. CONSTRUCTION — White, compact, low-profile contemporary design. Engineering-grade thermoplastic housing is impact-resistant, scratch-resistant and corrosion-proof. UL94V-O flame rating. UV-stable resin resists discoloration from natural and man-made light sources. Low-profile, integrated test switch/pilot light. Easily visible bright red status indicator. Unique track-and-swivel arrangement permits full range of direction of lamp head adjustment. Universal J-box mounting pattern. Tool-less access for maintenance. Thermoplastic Emergency Light OPTICS — Two LED lamp heads with polycarbonate lens, 12 series-parallel white LEDs each, provide redundant light sources to ensure emergency lighting performance. Typical LED lamp life is 10 years. ELECTRICAL — Dual-voltage input capability (120/277V). Edge connector on printed circuit board ensures long-term durability. Current-limiting charger maximizes battery life and minimizes energy consumption. Provides low operating costs. ELM2 LED Short-circuit protection — current-limiting charger circuitry protects printed circuit board from shorts. Thermal compensation adjusts charger output to provide optimum charge voltage relative to ambient tem- perature. LED Lamp Head Regulated charge voltage maintains constant-charge voltage over a wide range of line voltages. Prevents over/ Ni-Cad Battery undercharging that shortens battery life and reduces capacity. Filtered charger input minimizes charge voltage ripple and extends battery life. AC/LVD reset allows battery connection before AC power is applied and prevents battery damage from deep discharge. BATTERY: Sealed, maintenance-free nickel-cadmium battery delivers 90 minute capacity to emergency lamps. Two-state constant-current charge maximizes battery life and automatically recharges after battery discharge. Low-voltage disconnect prevents excessively deep discharge that can permanently damage the battery. Optional high-output battery available to power both local and optional LED remote lamp heads simultaneously. Self -Diagnostics (SD- Option) Single multi-color LED indicator to display two-state charging, test activation and three-state diagnostic test. Test switch provides manual activation of 30-second diagnostic testing for on-de- mand visual inspection. Self-diagnostic testing for 30 seconds every 30 days, 30 minutes at 180-day interval, and WARRANTY — 5-year limited warranty. (Battery is prorated). Complete warranty terms located at 90 minutes annually. Diagnostic evaluation of LED light source, AC to DC transfer, charging and battery condition. www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx. INSTALLATION — Ceiling- or wall-mount standard. Flexible conduit entry provision on top of the unit. Note: Actual performance may differ as a result of end-user environment and application. LISTINGS — UL damp location listed standard 50-104°F (10-40°C). Meets UL 924, NFPA 101 (current Life Safety All values are design or typical values, measured under laboratory conditions at 25 °C. Code), NEC and OSHA illumination standards. Specifications subject to change without notice.
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: ELM2 LED
ELM2 LED Series Lamp type Housing Options ELM2 LED Two 1.5W/3.6V white LED (blank) White HO High-output ni-cad battery for 6W remote capacity 1 B Black SD Self-diagnostics NOM Meets Mexican standards
Notes 1 Not available with NOM. Accessories: Order as separate catalog number. 2 Only available with HO option. See spec sheet ELA Q LED. ELA Q L0304 SD Single LED indoor remote head, white, self-diagnostics 2,3,4 ELA Q L0304 Single LED indoor remote head, white 2,3,4 3 Also available in black. Add "B" after ELA to ELA T Q L0304 SD Twin LED indoor remote head, white, self-diagnostics 2,3,4 ELA T Q L0304 Twin LED indoor remote head, white 2,3,4 order black finish. Example: ELA B Q L0304 SD. See spec sheet ELA Q LED. ELA QWP L0304 SD Single LED weather-proof remote head, gray, self-diagnostics 2,3,4 ELA QWP L0304 Single LED weather-proof remote head, gray 2,4 4 Only compatible with Quantum LED series. ELA T QWP L0304 SD Twin LED weather-proof remote head, gray, self-diagnostics ELA T QWP L0304 Twin LED weather-proof remote head, gray 2,4 5 See spec sheet ELA VS-VS2 ELA WG1 Wireguard, 15” W x 13-1/2” H x 6” D (See spec sheet ELA-WG) ELAVS Thermoplastic vandal shield5
EMERGENCY ELM2-LED Catalog Number
Notes APPLICATION GUIDE: STANDARD SPECIAL SIGNAGE Lithonia Lighting offers special signage signs to suit many applications. The Signature and Quantum Type families highlighted below are illuminated with energy-efficient, long-life Light Emitting Diodes (LEDs). WARRANTY — Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx Actual performance may differ as a result of end-user environment and application. Note: Specifications subject to change without notice.
LE P LQM P LHQM P Signature Quantum Quantum
AREA OF AREA OF AREA OF AREA OF RESCUE RESCUE REFUGE RESCUE ASSISTANCE ASSISTANCE
SW01 SW02 SW03 SW04
BEAM DARKROOM IN USE IN USE EXIT EXIT SW05 SW06 SW07 SW08
IN LASER MAGNET NO USE IN USE IN USE EXIT SW09 SW10 SW11 SW12
ON ROOM X-RAY AIR IN USE SALIDA IN USE SW13 SW14 SW15 SW16 SW17
ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: LE P 1 R 120/277 EL N SW02
Family Face type Housing color Number of faces Letter color Input voltage Operation6
LE Signature die-cast aluminum sign1 P Panel (blank) Matte black, brushed 1 Single face R Red 120/277 Dual voltage (blank) AC only aluminum face LQM Quantum thermoplastic sign2,3 2 Double face G Green EL N Nickel-cadmium W White LHQM Quantum thermoplastic2,4 3 Single face with extra battery faceplate and color panel5
Special wording
SW01 AREA OF REFUGE7 SW05 BEAM IN USE7,8 SW09 IN USE7,8 SW13 ON AIR7,8 SWO2 AREA OF RESCUE7 SWO6 DARK ROOM IN USE7,8 SW10 LASER IN USE7,8 SW14 ROOM IN USE7,8 SWO3 AREA OF RESCUE ASSISTANCE7 SWO7 EXIT Arabic/English9,10 SW11 MAGNET IN USE7,8 SW15 SALIDA9,10 SW04 AREA OF RESCUE ASSISTANCE with access pictogram7 SW08 EXIT with access pictogram10 SW12 NO EXIT10 SW16 X-RAY IN USE7,8 SW17 Handicap Symbol7
Notes 6 Leave blank for LHQM family. 1 See spec sheet LE-LRE for complete specifications 7 UL Listed as an electric sign. 2 Only available in white housing. 3 See spec sheet LQM for complete specifications 8 Not available with LHQM family or EL N operation. 4 See spec sheet LHQM for complete specifications 9 Only available in red letter color. 5 Only available with LQM or LHQM family. 10 Not available with UL listing.
EMERGENCY CUSTOM-SIGNAGE Catalog Number
Notes FEATURES & SPECIFICATIONS INTENDED USE — Ideal for applications requiring general purpose emergency lighting exit sign. Type CONSTRUCTION — Die-cast aluminum construction – compact housing. Brushed aluminum faceplate with matte black electrostatic polymeric trim. Clear lacquer finish on brushed face inhibits fingerprints and other surface contaminants. Also available in white housing. Fully overlapping light seal prevents light leaks. Universal directional chevron knockouts are concealed and easily removed. Provisions for conduit entry and pendant mounting. Letters 6” high with 3/4” stroke, with 100 ft viewing distance rating, based upon UL924 standard. U.S. Patent No. 5,739,639. Other patents pending. Die-Cast Aluminum Exit OPTICS — The typical life of the exit LED lamp is 10 years. ELECTRICAL — Dual-voltage input capability 120 or 277 VAC. Emergency models provided with test switch, status indicator and a battery that automatically recharges when normal power is restored. Battery option: Emergency models provided with maintenance-free, sealed nickel-cadmium battery which LQC provides 90 minutes of emergency power. INSTALLATION — Quick-mount installation - less than 5 minutes. Universal mounting (top or end). Back mount - only available with single face. Completely concealed, easily removed mounting knockouts and hole plugs. No exposed hardware. Die-cast aluminum canopy provided. Faceplate accessory kit available LED LAMPS for 1-face to 2-face field conversion, see accessories below. LISTINGS — UL listed. Damp location listing 50°F to 104°F (10°C to 40°C). Meets UL 924, NFPA 101 (current Life Safety Code), NFPA 70-NEC and OSHA illumination standards. NEMA Premium certified. WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx Specifications 8-1/4 Actual performance may differ as a result of end-user environment and application. (20.9) Length: 11-3/4 (29.8) All values are design or typical values, measured under laboratory conditions at 25 °C. Depth: 2 (5.1) Note: Specifications subject to change without notice. 11-3/4 2 Height: 8-1/4 (20.9) (29.8) (5.1) Weight: 4.5 lbs. (2.0 kg) All dimensions are inches (centimeters) unless otherwise specified.
ORDERING INFORMATION All configurations of this product are considered standard and have short lead times. Example: LQC 1 R EL N
LQC Family Housing color Number of faces Letter color Operation
LQC (blank) Matte black, brushed 1 Single face R Red (blank) AC only 120/277 aluminum face 2 Double Face G Green EL N 120/277 VAC input with nickel-cadmium battery back-up W White
Accessories: Order as separate item.
ELA WG1 Back-mount wireguard1 ELA WGEXT Top-mount wireguard1 ELA WGEXE End-mount wireguard1 ELA B US12 12” pendant-mount kit with black canopy. To order white canopy, replace B with W in catalog number. To order 24” or 36” lengths, replace 12 with 24 or 362 ELA LQCFPK Brushed/black faceplate kit with red and green sign panel for 1-face to 2-face field conversion ELA LQCBPK Brushed/black aluminum backplate for 2-face to 1-face field conversion ELA W LQCBPK White backplate for 2-face to 1-face field conversion Notes ELA W LQCFPK White faceplate kit with red and green sign panel for 1-face to 2-face field conversion 1 See spec sheet ELA-WG. 2 See spec sheet ELA-StemKits.
EMERGENCY LQC IC – RATED BUY AMERICAN ACT OF 2009 COMPLIANT FINELITE High Performance 2" Aperture (HP-2) - Recessed
stry B u e d s n t I 1010 Date Year LED Warranty Project
Type
0 Comments
DESCRIPTION High Performance 2" Aperture Recessed (HP-2 R) is a patented, linear recessed LED luminaire. The micro shape delivers excellent performance in a 2" aperture using an advanced optical design and mid-power LEDs. This long-life luminaire is free of socket shadows and can be specified in rows or configurations.
90° Wall to Ceiling
4" Tailored Lighting 10 working days
2 1/4"
DIMENSIONS & LIGHT ENGINE MITERED ANGLES TAILORED LIGHTING A glare-free experience is attained with mid-power LEDs Illuminated 90º corners and wall-to-ceiling Any length greater than 2 feet, in increments properly distributed and paired with a precise diffuser to configuration are seamless without socket down to 1/16th-inch (± 1/32") and 90-degree eliminate pixilation. Aperture: 2.25" shadows. Custom angles are available (90º mitered corners in a single plane. minimum on inside corners). Contact factory.
ORDERING GUIDE Sample Number: HP-2 R - 32' - S - 835 - F - 120V - SC - C1 - OBO
HP-2 R
Finelite Series HP-2 R Length (Minimum 2' , increments accurate to 1/16th" (± 1/32"), standard) Light Output ( S - Standard, B - Boosted Standard, H - High, V - Very High) LED CRI/CCT ( 830 - 80 CRI min, 3000K, 835 - 80 CRI min, 3500K, ©
2
840 - 80 CRI min, 4000K, 930 - 90 CRI min, 3000K, 0 1 6
935 - 90 CRI min, 3500K, 940 - 90 CRI min, 4000K F I N E L
Downlight Diffuser ( F - Flush (standard)) I T E ,
Voltage ( 120V , 277V ) I N C .
Circuiting ( SC - Single Circuit)* A L L
Ceiling Type ( C1 - 1" T-Bar, C2 - 9/16" T-Bar, C3 - screw slot, C3F - flush screw slot, VF - Visible Flange, C2T - 9/16" tegular, R I G H
C1T - 1" tegular, SF - Spackle Flange, TZ4 (C1, C2, C2T, C3, C3F) - tech zone 4") T S
R
Integrated Sensors ( OBO - Occupancy Sensor, OBD - Daylight, OBB - Both) E S E R V E D .
F o
*Contact factory for switching options. r m
C
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S T K 0 1 1
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • 510 / 441-1100 • Fax: 510 / 441-1510 • www.finelite.com 4 .
1 1 / 1
Due to continuing product improvements, Finelite reserves the right to change specifications without notice. Please visit www.finelite.com for most current data. Page 1 6 BUY AMERICAN ACT OF 2009 COMPLIANT FINELITE High Performance 2" Aperture (HP-2) - Indirect/Direct
stry B u e d s n t I 1010 Date Year LED Warranty Project Top Glow Diffuser (Standard) Type
Comments
Bottom Glow Diffuser (Shown)
DESCRIPTION High Performance 2" aperture Indirect/Direct (HP-2 ID) is a patented, linear LED luminaire with Flush, Top Glow™ and Bottom Glow™ options for up- and downlight. The micro shape delivers excellent performance using an advanced optical design and mid-power LEDs to achieve 90% of initial light output at 100,000 hours.
Top Glow Diffuser (Standard)
0.2" Tailored Lighting 4 3/4" 4 3/4" 10 working days 0.2" 2 1/4" 2 1/4" Bottom Glow Diffuser Flush Uplight and (Optional) Downlight Diffuser
DIMENSIONS & DIFFUSER BOTTOM GLOW DIFFUSER TAILORED LIGHTING A glare-free experience is attained with mid-power The optional Bottom Glow diffuser adds a clean Any length greater than 2 feet, in increments down LEDs and a precise diffuser to eliminate pixilation. line of light along the downlight element. to 1/16th-inch (± 1/32") and 90-degree mitered corners in a single plane.
ORDERING GUIDE Sample Number: HP-2 ID - 32' - S - H - 8 - 35 - TG - F - 120V - FA - SC - C1 - OBO
HP-2 -ID Finelite Series HP-2 ID Length (Minimum 2', increments accurate to 1/16th" (± 1/32"), standard) Uplight Output (S - Standard, B - Boosted Standard, H - High, V - Very High) ©
Downlight Output (S - Standard, B - Boosted Standard, H - High, 2 0 1 6
V - Very High)
F I N
LED CRI (8 - 80 CRI min (standard), 9 - 90 CRI min) E L I T E
LED Color Temperature (30 - 3000K, 35 - 3500K, 40 - 4000K) ,
I N C
Uplight Diffuser Option (TG - Top Glow (standard), F - Flush) .
A L
Downlight Diffuser Option (F - Flush (standard), BG - Bottom Glow) L
R I G
Voltage (120V, 277V) H T S
Mounting (FA - Fully Adjustable) R E S E
Circuiting (SC - Single Circuit, DC - Dual Circuit)* R V E
Ceiling Type (C1 - 1" T-Bar, C2 - 9/16" T-Bar, C3 - screw slot, C4 - hard ceiling) D .
F
Integrated Sensor (OBO - Occupancy Sensor, OBD - Daylight) o r m
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S C * Contact factory for switching options. T K 0 1 1
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • 510 / 441-1100 • Fax: 510 / 441-1510 • www.finelite.com 5 .
0 8 / 1
Due to continuing product improvements, Finelite reserves the right to change specifications without notice. Please visit www.finelite.com for most current data. 6 LED P9000 | Recessed
PRULITE.COM 213.746.0360
Type:
Job:
13˝, 19˝, 24˝, 36˝ or 48˝
71/4˝-81/4˝7¼”-8¼” ad j. adj.
111/8˝ , 171/4˝ , 221/4˝ 341/4˝ or 461/4˝
LOW MED STD HIGH 12˝: lm 550 700 1100 1400 w 14 18 28 35 18˝: lm 950 1650 1950 2150 w 19 33 39 47 Clean, radiant, celestial, at times almost invisible. 2’: lm 2100 3150 3900 5300 P9040-LED35LO-FWA w 35 54 67 97 P9000 – a slimmer, refined version of P8900 – minimal 7/16˝ trim or 7017 Delivered Lumens 88 Watts 3’: lm 4500 7000 9000 13275 trimless with flush lens that melts into its environment. Optional w 56 87 113 177 80 lm/w drop down lens creates a playful ‘bubble-like’ effect. 4’: lm 7000 8800 13900 21000 w 88 110 174 281 Perfect partner to our P4000 Sky Oculus pendant. Lumen output may vary +/- 5%
LED WARRANTY LED WARRANTY 4000K used for lm/ft estimates above 3500K –2% llf, 3000K –4%, 2700K –6% 5YEAR 5YEAR See LED Details PDF for more info
SERIES LED OUTPUT SHIELDING TRIM COLOR CIRCUITING VOLTAGE CEILING SYSTEMS DRIVERS OPTIONS & COLOR CONTROLS
P9012 LED27 LO FWA TMW SC Single 347 X1 T-Bar Exposed ND Non-Dimming EML Emergency 12˝ Dia. 2700K Low Flush-Flat Textured Circuit Battery, Low White Acrylic Matte White UNV X3 Hard Ceiling DM10 0-10v, 10% Dimming P9018 LED3 MO Lens (Standard) (120-277) (Flange Trim) (Standard) EMH Emergency 18˝ Dia. 3000K Medium (Standard) Battery, High YGW X7 Hard Ceiling DM01 0-10v, 1% Dimming (NA 12,˝ 18˝ and 2´) P9020 LED35 SO DWA Gloss White (Trimless Mud-over Flange) STEP Step Dimming, CP 2´ Dia. 3500K Standard Drop White 100-50-Off, Osram Acrylic Lens Y__ Chicago Plenum P9030 LED4 HO (Flat lens dropped Premium NOTE: Lumens and watts per foot may 3´ Dia. 4000K High 1˝ below ceiling Color differ for STEP drivers, consult factory PRUBIN plane) Meticulous Bin- P9040 PROG CC LDE5 5%, Lutron ning and Labeling 4´ Dia. Program- Custom (Ecosystem) every LED Board mable Light Color LDE1 1%, Lutron within a 2-step Output (Soft Fade to Black, Ecosystem) MacAdams Ellipse (Specify desired lumens or watts L3DA 1%, Lutron, 3 Wire per fixture) ECO 1% 0-10v, EldoLED ECDA 1% DALI, EldoLED SOLO 0.1% 0-10v, EldoLED (Dim to Dark) SODA 0.1% DALI, EldoLED (Dim to Dark)
Prudential Ltg. reserves the right to change design specifications or materials without notice. Please visit www.prulite.com for most current data. © 2014 All rights reserved – All products manufactured at: Prudential Ltg. 1774 E. 21st Street, Los Angeles, CA 90058 Sky Oculus Series 1 10-10-2016 LED P4000 | Pendant & Surface
PRULITE.COM 213.746.0360
Type:
Job:
Smooth extruded aluminum side wall
Minimal trim with clean, sharp edge
5˝
18˝, 26˝, 37˝ or 455/8˝
LUMEN OUTPUT: Direct (D1) LOW MED STD HIGH 18˝: lm 950 1650 1950 2150 A sharper, Euro version of our P3900. P4030-LED35-SO-FWA w 19 33 39 47 11889 Delivered 2’: lm 2100 3150 3900 4100 Lumens Four decades after launching our Sky Oculus P3900 we launched w 35 54 67 73 113 Watts a sleeker, more bold and modern big round. Often specified in 3’: lm 5800 9100 11889 17700 106 lm/w w 56 87 113 177 one of our twenty one premium colors (no set-up fee). Light Labs #L031511001 4’: lm 9200 11500 18200 28000 w 88 110 174 281 Lumen output may vary +/- 5% D9 ON
LED WARRANTY LED WARRANTY 4000K used for lm/ft estimates above NEXT PAGE 3500K –2% llf, 3000K –4%, 2700K –6%
5YEAR 5YEAR See LED Details PDF for more info
SERIES LED OUTPUT SHIELDING COLOR/ DISTRI- CIRCU- VOLT- MOUNTING CEILING DRIVERS OPTIONS & COLOR FINISH BUTION ITING AGE SYSTEMS CONTROLS
P4018 LED27 LO Low FWA TMW D1 SC 347 SUR Surface X1 T-Bar ND Non-Dimming, Osram EML 18˝ Dia. 2700K Flat White Textured Direct Single Mount Exposed Emergency (11 lbs) MO Acrylic Lens Matte Circuit UNV (Standard) DM10 0-10v, 10% Dimming Battery, LED3 Medium (Standard) White D9 (120- MPCA (Standard) Low P4020 3000K Semi- DC 277) Monopoint X3 SO DM01 0-10v, 1% Dimming 2´ Dia. VWA YGW Direct Dual Mounting Hard EMH (22 lbs) LED35 Standard Convex White Gloss White (20-30% Circuit (For 18” & 2’ - 9” min. Ceiling STEP Step Dimming, Emergency 3500K Acrylic Lens (Standard) uplight, (D9 only) from fixt. to ceiling, 100-50-Off, Osram Battery, P4030 HO (1˝ Max drop) NA Surface) for 3’ & 4’ fixt. 18” X6 LED4 High NOTE: Lumens and watts per foot may High 3´ Dia. Y__ from fixt. to ceiling) Slot Grid (NA with 18˝ (35 lbs) 4000K Note: differ for STEP drivers, consult factory PROG Premium NA - 18˝, 2´ and 2´) Color CA48˝, 96˝ or P4040 Program- D9 DC LO 144˝ LDE5 5%, Lutron IBC Insulat- 4´ Dia. mable CC 18˝mini- Aircraft Cable (Ecosystem) ed Braided (50 lbs) Light mum from (Adjustable) Custom fixture to LDE1 1%, Lutron Cord Output Color (Soft Fade to Black, Ecosystem) (Specify ceiling SSC__ PRUBIN desired lm or Note: Top recom- mended. Top-Swivel L3DA 1%, Lutron, 3 Wire Meticulous w/ fixture) plate is always Stem Mount for Binning and Gloss White Hard Ceilings ECO 1% 0-10v, EldoLED Labeling for optical (Specify length in performance ECDA 1% DALI, EldoLED Every LED inches) Board Note: 4018 SUR SOLO 0.1% 0-10v, EldoLED Within or MPCA only (Dim to Dark) a 2-Step SODA 0.1% DALI, EldoLED MacAdams (Dim to Dark) Elipse
Prudential Ltg. reserves the right to change design specifications or materials without notice. Please visit www.prulite.com for most current data. © 2014 All rights reserved – All products manufactured at: Prudential Ltg. 1774 E. 21st Street, Los Angeles, CA 90058 Sky Oculus Series 1 10-10-2016 Catalog Number
FEATURES & SPECIFICATIONS Notes INTENDED USE — The VT Series Volumetric LED Troffer (VTL) combines the aesthetics and high performance with intelligent LED engines for applications such as offices, schools, retail locations and hospitals. High- efficacy light engines deliver long life and excellent color, ensuring a superior quality lighting installation Type that is highly efficient and sustainable. Multiple lumen packages and driver options provide solutions for all your lighting applications. Featured nLight control system provides design flexibility and ease of installation and optimum energy savings. CONSTRUCTION — Rugged, one-piece cold-rolled steel coated polyester, painted after fabrication with embossed facets. Impact-modified, single clear acrylic diffuser provides excellent shielding and wide VT Series Volumetric LED Troffer distribution. End plates include integral T-bar clips. Fixture may be mounted and wired in continuous rows. ADP Total fixture height is only 4-3/8". OPTICS — Volumetric illumination is achieved by creating an optimal mix of light to walls, partitions, vertical and horizontal work surfaces — rendering the interior space, objects and occupants in a more balanced, complementary luminous environment. Linear faceted reflector cavity softens and distributes light into 2VTL the space while minimizing luminous contrast between the fixture and ceiling. Sloped end plates provide a smooth, luminous transition between fixture and ceiling while enhancing the perception of fixture depth. High-performance diffuser provides LED concealment, even illumination across the diffuser and improved ADPT 2' x 2' lumen-per-watt performance. LED Now available with two different aesthetics including the standard Acrylic Linear Prismatic Diffuser (ADP) and the Acrylic Linear Prismatic Diffuser with Diffuser Trim Rings (ADPT). ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality of illumination for extended service life. 90% LED lumen maintenance at 60,000 hours (L90/60,000). eldoLED driver options deliver choice of dimming range, and choices for control, while assuring flicker-free, low-current inrush, 89% efficiency and low EMI. Optional integrated nLight®controls make each luminaire addressable - allowing it to digitally communicate with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply connect all the nLight enabled control devices and the VTLED luminaires using standard Cat-5 cabling. Unique plug-and-play convenience as devices and luminaires automatically discover each other and self-commission. Lumen Management: Unique lumen management system (option N80) provides on board intelligence that actively manages the LED light source so that constant lumen output is maintained over the system life, preventing the energy waste created by the traditional practice of over-lighting. Step-level dimming option allows system to be switched to 50% power for compliance with common energy codes while maintaining fixture appearance. Driver disconnect provided where required to comply with US and Canadian codes. SENSOR— Integrated sensor (individual control): Sensor Switch MSD7ADCX ((Passive infrared (PIR)) or MSDPDT7ADCX ((PIR/Microphonics Dual Tech (PDT)) integrated occupancy sensor/automatic dimming photocell allows the luminaire to power off when the space is unoccupied or enough ambient light is entering the space. See page 2 for more details on the integrated sensor. Integrated Sensor (nLight Wired Networking): This sensor is nLight-enabled, meaning it has the ability to communicate over an nLight network. When wired, using CAT-5 cabling, with other nLight-enabled sensors, power packs, or WallPods, an nLight control zone is created. Once linked to a Gateway, directly or via a Bridge, the zone becomes capable of remote status monitoring and control via SensorView software. See page 2 for the nLight sensor options. INSTALLATION — Unique grid interfacing arrangement provides mounting into standard 1" and 9/16" tee bar or screw slot grids. 9/16" allows fixture trim to hang level with architectural ceiling tiles. Drywall ceiling adaptors available. Suitable for damp location. LISTINGS — CSA Certified to meet U.S. and Canadian standards. IC rated. DesignLights Consortium® (DLC) qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified. WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx NOTE: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25°C. Specifications subject to change without notice.
Capable Luminaire This item is an A+ capable luminaire, which has been designed and tested to provide consistent color appearance and out-of-the-box control compatibility with simple commissioning. • All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency • This luminaire is part of an A+ Certified solution for nLight® control networks when ordered with drivers marked by a shaded background* • This luminaire is part of an A+ Certified solution for nLight control networks, providing advanced control functionality at the luminaire level, when selection includes driver and control options marked by a shaded background* To learn more about A+, visit www.acuitybrands.com/aplus. *See ordering tree for details
LED 2VTL-2X2 Luminaire Type: Catalog Number (autopopulated):
Gotham Architectural Downlighting LED Downlights 4” Evo® Downlight
Solid-State Lighting
FEATURES OPTICAL SYSTEM ELECTRICAL SYSTEM • Self-flanged or flangeless semi-specular, matte-diffuse or specular finishing trim • Fully serviceable and upgradeable lensed LED light engine • Patented Bounding Ray™ optical design (U.S. Patent No. 5,800,050) • 70% lumen maintenance at 60,000 hours • 45° cutoff to source and source image • Tested according to LM-79 and LM-80 standards • Top-down flash characteristic • Overload and short circuit protected • Polycarbonate lens integral to light engine • 2.5 SDCM; 85 CRI typical, 90+ CRI optional MECHANICAL SYSTEM LISTINGS • 16-gauge galvanized steel construction; maximum 1-1/2” ceiling thickness • Fixtures are CSA certified to meet US and Canadian standards; wet location, • Telescopic mounting bars maximum of 32” and minimum of 15”, preinstalled, covered ceiling 4” vertical adjustment WARRANTY • Toolless adjustments post installation • 5-year limited warranty. Complete warranty terms located at: • Junction box capacity: 8 (4 in, 4 out ) 12AWG rated for 90°C www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx • Light engine and driver accessible through aperture • Injection molded mud ring included with flangeless trims. Ships separately. Note: Actual performance may differ as a result of end user environment and application. Installs independently of the mounting frame to reduce cracks in plaster due to All values are design or typical values, measured under laboratory conditions at vibration. 25° C. ORDERING INFORMATION ORDERING A+ Capable options indicated by this color background.
EXAMPLE: EVO 35/10 4AR MWD LSS MVOLT EZ1
Series Color temperature Nominal lumen values Aperture/Trim color Trim Style Distribution Finish Voltage EVO 27/ 2700 K 07 750 lumens 4AR Clear (blank) Self-flanged MD Medium LSS Semi-specular MVOLT 30/ 3000 K 10 1000 lumens 4PR Pewter FL Flangeless (0.9 s/mh) LD Matte-diffuse 120 35/ 3500 K 15 1500 lumens 4WTR Wheat MWD Medium wide LS Specular 277 40/ 4000 K 20 2000 lumens 4GR Gold (1.0 s/mh) 3472 25 2500 lumens 4WR1 White WD Wide (1.2 s/ 30 3000 lumens 4BR1 Black mh) 4WRAMF1 White anti- microbial
Driver3 Options EZ10 eldoLED 0-10V ECOdrive. Linear dimming to 10% min. SF Single fuse. Specify 120V or 277V. BGTD Bodine generator transfer EZ1 eldoLED 0-10V ECOdrive. Linear dimming to 1% min. TRW6 White painted flange device. Specify 120V or 277V. EZB eldoLED 0-10V SOLOdrive. Logarithmic dimming to <1%. TRBL7 Black painted flange CRI90 High CRI (90+). Specify 120V EDAB eldoLED SOLOdrive DALI. Logarithmic dimming to <1%. EL8 Emergency battery pack with or 277V. EDXB eldoLED POWERdrive DMX with RDM (remote device management). Square integral test switch CP10 Chicago plenum Law dimming to <1%. Includes termination resistor. Refer to DMXR Manual. ELR8 Emergency battery pack with RRL__ RELOC®-ready luminaire EXA1 XPoint Wireless, eldoLED 0-10V ECOdrive. Linear dimming to 1%. Refer to remote test switch connectors enable a simple XPoint tech sheet. NPS80EZ5 nLight® dimming pack controls and consistent factory installed EXAB XPoint Wireless, eldoLED 0-10V SOLOdrive. Logarithmic dimming to <1%. 0-10V eldoLED drivers. option across all ABL luminaire Refer to XPoint tech sheet. NPS80EZER5,9 nLight® dimming pack controls brands. Refer to RRL for com- ECOS24,5 Lutron® Hi-Lume® 2-wire forward-phase driver. Minimum dimming level 0-10V eldoLED drivers. ER con- plete nomenclature. 1%. Minimum lumen 1000/Maximum lumen 3000. trols fixtures on emergency circuit. ECOS34,5 Lutron® Hi-Lume® 3-wire or EcoSystem® dimming driver. Minimum dim- ming level 1%. Minimum lumen 1000/Maximum lumen 4500.
EVO-4-Open GOTHAM ARCHITECTURAL DOWNLIGHTING | P 800.315.4982 | gothamlighting.com PAGE 1 OF 4 © 2010-2016 Acuity Brands Lighting, Inc. All Rights Reserved. Rev. 10/12/16. Specifications subject to change without notice. LCL LED Lensed Striplight
FEATURES • Long life 50,000 hour LEDs at L80 for reduced • LED boards and driver accessible for future maintenance maintenance or upgrades • Four LED color choices • Modular replaceable LED components • Four lumen packages per size • Surface mount, wall mount or suspended • Superior color consistency within a 3-step • Five year warranty (Terms and Conditions apply) MacAdam ellipse and greater than 80 CRI • Maximum temperature 35°C on all lumen • Available in 2', 4' or 8' lengths packages up to HL
STRIPLIGHTS • Optional integral emergency battery pack • Heavy die-formed steel channel with 100% acrylic formed diffuser • Fully assembled fixture for quick installation
ORDERING INFORMATION
LCL – – – –
MODEL SIZE COLOR TEMP LUMEN OUTPUT DRIVER VOLTAGE OPTIONS LCL LED Open 4 4' 30 3000K LW Low Watt E Fixed Output U 120V-277V ELL14 Emergency Battery Pack, 1,2,3 Striplight 8 8' 35 3500K ML Medium Lumen ESD Step Dimming 347 347 1400 Lumens 40 4000K HL High Lumen ED 0-10V Dimming (E,ED,ED1 GLR Fast Blow Fuse only) 50 5000K VL Very High Lumen PAF Paint After Fabrication See Product Availability NYC NYC Compliant Table below.
ACCESSORIES (ORDER SEPARATELY) S18 18" Stem, Canopy 1 For compatibility with Dual-Lite LiteGear® inverters in lieu of installed Battery Pack, contact Hubbell Lighting Representative. SS18 18" Swivel Stem—45° Swivel 2 Not available in 2 ft size. CSHC Chain Hanger Assembly 3 Not available in VL package.
96" 45⁄8" 3" PRODUCT AVAILABILITY A A A LUMEN ANOMINAL LUMENSA NOMINAL SIZE EFFICACY B B PACKAGE B(3500K) AWATTS 48" 2' ML 2,500 25 100 41⁄2" 41⁄8" 4' LW 2,500 25 100 48" ML 5,000 48 104 45⁄8" 3" A A A A A A HL 6,100 55 110 BB BB313⁄16" A VL 10,100 96 105 241⁄8" A - 7/8" Diameter Knockout 8' LW 5,000 48 104 B - 5⁄16" x 1⁄2" hole ML 10,100 96 105 Note 1: All Non-Shielded (strip) fixtures—deduct 1/16" from overall dimension for continuous row mounting. Dimensions shown include end panel. HL 12,200 111 110 VL 20,100 193 104 Lumens vary according to color temperatures and other factors. See specific photometric test(s).
20 Catalog Number
Notes FEATURES & SPECIFICATIONS INTENDED USE —The T Series LED combines digital lighting and control technologies with a high- Type performance optical system to deliver general ambient lighting for many applications such as schools, offices and hospitals. High-efficacy light engine delivers long life and excellent color, ensuring a superior quality lighting T SERIES LED installation that is highly efficient and sustainable. Certain airborne contaminants can diminish the integrity of acrylic and/or polycarbonate. Click here for Acrylic-Polycarbonate Compatibility table for suitable uses. CONSTRUCTION — Housing formed from cold-rolled steel. Housing is painted after fabrication for superior finish. 2TL Smooth hemmed sides and smooth inward-formed end flanges, for easy handling. Standard extruded aluminum door frame has superior structural integrity with premium appearance and mitered corners. Door frame is painted after fabrication, standard. Powder-painted rotary cam latches 2' x 4' LED provide easy, secure door closure. Integral T-bar clips are standard. Acrylic shielding material is 100% UV stabilized. OPTICS — Standard pattern #19 lens, 0.156" thick with highly transmissive overlay, is standard for superior brightness control. Overlay is 0.040" thick. Other lenses are available. ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior level and quality of illumination for extended service life. 90% LED lumen maintenance at 60,000 hours (L90/60,000). eldoLED driver options deliver choice of dimming range, and choices for control, while assuring flicker-free, low-current inrush, 89% efficiency and low EMI. Optional nLight® embedded controls continuously monitor system performance, allow for constant lumen management/compensation function, facilitate simple "plug-and-play" network and controls upgrading via Cat-5 cable. Driver disconnect is provided where required to comply with U.S. and Canadian codes. INSTALLATION — Drivers and internal components are accessible from floor. LED boards include plug-in Specifications 3-3/4 connectors for easy replacement or servicing. Suitable for direct insulation contact. Suitable for damp Length: 48 (122.0) location. (9.5) Width: 24 (61.0) LISTINGS — CSA certified to U.S. and Canadian standards. IC rated. DesignLights Consortium® (DLC) 24 Premium qualified product. Not all versions of this product may be DLC Premium qualified. Please check Depth: 3-3/4 (9.5) (61.0) the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified. All dimensions are inches (centimeters) unless otherwise noted. WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx Note: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 °C. Specifications subject to change without notice.
Capable Luminaire This item is an A+ capable luminaire, which has been designed and tested to provide consistent color appearance and out-of-the-box control compatibility with simple commissioning. • All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency • This luminaire is part of an A+ Certified solution for nLight® control networks when ordered with drivers marked by a shaded background* • This luminaire is part of an A+ Certified solution for nLight control networks, providing advanced control functionality at the luminaire level, when selection includes driver and control options marked by a shaded background* To learn more about A+, visit www.acuitybrands.com/aplus. *See ordering tree for details
LED 2TL-2X4 15774 Gateway Circle PH: 714.259.9959 Wila By Ledra Brands Inc. www.wilalighting.com Tustin, CA 92780 FAX: 714.259.9969
Job Name: Contact:
Ordering Code: Fixture Type:
608 Architectural Cylinder - 6”
Description The 608 Architectural Cylinder provides energy efficient light using the latest technology on the market including industry best color consistency allowing for a SDCM of 1x2. Multiple reflector beam spreads, finishes and LiteOptics allow for creative lighting solutions to illuminate architectural spaces. Easy installation with quick connect and bayonet mounting. 608 carries a 5 year NO COLOR SHIFT AND FIXTURE WARRANTY.
Housing Extruded aluminum housing with Black, White or Matte Silver finish
Mounting Easy bayonet mounting system over a 3-1/2”to 4” recessed round or octagonal j-box. Surface mount or canopy mount with 4 foot field cuttable rigid stem. Electrical / LED Driver Electronic multi-voltage 120-277V driver, 50/60Hz. Replaceable LED module with quick disconnects. 50/60Hz , 43 Watts Listings - ETLus Listed to UL1598 (suitable for dry and damp locations) - cETL Listed to CSA C22.2 #250.0 - Made in the USA - meets the requirements of the Buy American provision within the ARRA.
Ordering Codes
Follow the steps to specify your fixture, example: 608RA-6-XTM19-20LM-35K-98-DA60-UNV-10V-mc-MP
Part Number Aperture LED Delivered Lumen CCT CRI Reflector Voltage
608RA 6 6” XTM19 13LM2 1105 lm 27K 2700K 83 83 CRI DA20 diffuse, 20º UNV 120V-277V 20LM2,4 1700 lm 30K 3000K 981,2 98 CRI DA40 diffuse, 40º 30LM4 2550 lm V30K 3000K Vibrant DA60 diffuse, 60º 40LM1,4 3400 lm 35K 3500K SA20 specular, 20º 50LM1,3,4 4250 lm 40K 4000K SA40 specular, 40º B27K2 2700K Beauty SA60 specular, 60º
Dimming Finish Mounting Options Notes
10V standard 0-10V dimming to 10% bk black S Surface Mount 1. 98 CRI not available for 40LM and 50LM. LUDA3 Lutron Hi-lume/EcoSystem A-Series -to 1% mc matte silver P Pendant 2. B27K Beauty Series choose 98 CRI (actual 93). Available for 13LM and 20LM only. LUDH3 Lutron EcoSystem H-Series -to 1% wh white RP Rigid Pendant 3. LUDA, LUDH not available for 50LM. 4 DIM10 eldoLED 0-10V dimming to 1% W Wall 4. DIM10, DIM10Z, DALI, DALIZ not available for 40LM and 50LM. Available at 4 DIM10Z eldoLED 0-10V dimming to zero (0.1%) 85% Lumen output for 30LM and 20LM (98 CRI). DALI4 eldoLED DALI dimming to 1% DALIZ4 eldoLED DALI dimming to zero (0.1%)
In a continuing effort to offer the best product possible we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. v.8.29.16 608 Arch Cylinder Page 1 of 4 PROJECT INFORMATION MILLENIUM STRETCH™ Job Name MLHA12 SERIES Fixture Type PRODUCT FEATURES: Catalog Number »»Surface mount – ceiling or wall; 12"×24", 12"×36", Flat End Cap 12"×48", 12"×72", 12"×96" Approved by »»Extruded aluminum housing with decorative end caps »»Peace of Mind Guarantee® against breakage »»ADA compliant Rounded End Cap Reveal End Cap SPECIFICATIONS HOUSING: Marine grade aluminum. Extruded body with die-cast end caps. Housing, with end caps, post assembly TGIC polyester powder coat finished – 5-step pre-treatment. See Ordering Information for standard, optional, architectural and custom finishes. LENS: UV-stabilized, high impact extruded clear or pearlescent polycarbonate. Smooth exterior, linear prismatic interior. Nominal thickness .156". Lens securely positioned in body channels and end caps. Lens locked in place with tamper-resistant stainless steel Torx® with center pin fasteners and sealed with closed cell gaskets. END CAPS: Marine grade die-cast aluminum. Three styles available: Flat, Rounded and Reveal. Conduit and ”Wiremold™ ready” knockouts visible only from interior of end cap (Flat and Rounded styles only). SOCKETS: Shock-resistant sockets with internal locking collar to ensure positive lamp retention. REFLECTOR: Full reflector/wire cover – 92% reflectivity. HARDWARE: Stainless steel, tamper-resistant Torx fasteners secure lens in housing body's lens channel (four on 24", 36", and 48" housings; eight on 72" and 96" housings). ELECTRICAL: LED: Available 3500K, 4000K and 5000K color temperatures, 82 CRI. 120-277VAC, 50/60Hz electrical input with serviceable high power factor electronic, constant-current driver (<20% THD, >0.95 PF). Standard 0-10V dimming with 1-100% range, maximum driver source of 500 μA. Optional embedded microwave motion sensor (MS) has factory default settings of 20 minute time out, dims down to 30%. LF: Class P ballasts. Fluorescent electronic 120/277/347 and dual voltage ballasts high power factor. INSTALLATION: Standard four-point (24" housing) six-point (36" and 48" housings) and twelve-point (72" and 96" housing) mounting required for Peace of Mind Guarantee®. PHOTOMETRICS: Photometry tested to the IESNA LM-79-08 standard by an ILAC/ISO17025 accredited laboratory. For additional photometric data, please go to www.kenall.com. LED product ambient temperature is -30°C to 40°C, unless otherwise noted. WARRANTY: Limited ten (10) year warranty for LED Lamps. LISTINGS: UL and CUL listed for Wet Location – covered ceiling mount. UL certified IP64 per IEC 60598. Damp rated – ceiling mount. Corner, horizontal wall and pendant mount installation – damp location only. ADA compliant. Product listed on the Designlights Consortium® Qualified Products List. Check the latest version here for listed configuration details. Suitable for installation into -30°C to 40°C ambient environments, unless otherwise noted. In Stock SKU
MLHA12-48-R-MW-PP-45L40K-DCC-1-DV
MLHA12-48-F-MW-PP-45L40K-DCC-1-DV LED IP64 ADA MLHA12-48-F-MW-CP-2-32-IS-1-DV
ORDERING INFORMATION (Ex: MLHA12-48-F-MB-PP-90L40K-DCC-DV-FS-9500) Model Length End Cap Finish Lens Lamp Qty Lamp Type Ballast/Driver Type Circuit Qty Voltage Options Accessories MLHA12 Length Lamp Type Ballast/Driver Type Accessories 24 2' 2' Lengths DCC Dimming Constant Current (LED) CMB§ Corner Mount Bracket 36 3' 25L35K 25 Watt 3500K LED IS Instant Start Electronic <10% THD (T8,T8HO) (Must be ordered with DL Option) 48 4' 25L40K 25 Watt 4000K LED RS Rapid Start Electronic <10% THD (T8,T8HO,T5,T5HO) 9500 Torx® Screwdriver 72 Two 3' (factory connected) 25L50K 25 Watt 5000K LED SB Specified Ballast D-0552 Torx Driver Bit (Required for CMB Option) 96 Two 4' (factory connected) 45L35K 45 Watt 3500K LED 45L40K 45 Watt 4000K LED Circuit Quantity‡ † n/a on 2' T5/T5HO or 3' T5HO End Caps 45L50K 45 Watt 5000K LED 1 One fixtures with EL, PEL, or TN options. F Flat 14 F14T5 2† Two (Two Ballast Minimum) I n/a with 347V R Rounded 17 F17T8 b 347V available with EL and PEL RV Reveal 24I F24T5HO Voltage options only with two T8 lamps 120 120 Volts P 2' Fixtures have minimum 350-450 Finish 3' Lengths 277 277 Volts lumen battery pack LG Light Gray 21 F21T5 347 347 Volts (Consult Factory) W n/a on 2' fixtures MB Matte Black 25 F25T8 DV 120-277 Volts ‡ n/a with LED Lamp Options MW Matte White 39 F39T5HO § PM and CMB not available in conjunction CC Custom Color (Consult Factory) Options 4' Lengths ELP‡ 500 Minimum Lumen Battery Pack Lens 45L35K 45 Watt 3500K LED (90 Minutes; 32°F Starting Temperature) CP‡ Clear Polycarbonate 45L40K 45 Watt 4000K LED PELW‡ 1100 Minimum Lumen Battery Pack PP Pearlescent Polycarbonate 45L50K 45 Watt 5000K LED (90 Minutes; 32°F Starting Temperature) 67L35K 67 Watt 3500K LED LEL LED Emergency Battery Backup Lamp Quantity (Cross Section)‡ 67L40K 67 Watt 4000K LED (45L only, 32°F minimum operating temperature) 1 One 67L50K 67 Watt 5000K LED CDF Captive Diffuser Fasteners 2 Two 90L35K 90 Watt 3500K LED DL Damp Location (Interior use NO gasketing) 3 Three 90L40K 90 Watt 4000K LED FS Single Fuse & Holder (one per circuit) 4 Four 90L50K 90 Watt 5000K LED NAT Natatorium Environment Option 150L35K 150 Watt 3500K LED PH Phillips Head Fasteners 150L40K 150 Watt 4000K LED PM§ Pendant Mount (stems by others; damp only) 150L50K 150 Watt 5000K LED TNI‡ Twin Tube Night Light – 5/7/9 watts (120V only) 28 F28T5 UC‡ Uplight Component (Pendant Mount only; stems by 32 F32T8 others; damp only) 44 F48T8HO (2 lamp only) MS Motion Sensor (4' LED only) 54 F54T5HO 54A F54T5HO amalgam
www.kenall.com P: 800-4-Kenall F: 262-891-9701 10200 55th Street Kenosha, Wisconsin 53144 When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found at www.kenall.com/patents. Content of speci cation sheets is subject to change; please consult www.kenall.com for current product details. © 2016 Kenall Mfg. Co. All rights reserved. MLHA12-070816 Type: Approved: Fixture: Project:
ECVLX Color CoveLine is a low profile LED cove luminaire with 10 static color LED options, ECVLX Color CoveLine Pink, Violet, Light Blue, Spring Green, Yellow, Golden Yellow, Amber, Red, Green & Blue. ECVLX Color CoveLine available in 1 ft, 2 ft, or 4 ft nominal lengths. The housing is constructed of extruded aluminum with tooled end caps and IP20 rated for interior use only. Features Plug N’ Play connectors and other accessories for easy installation. Flicker free dimming to 3% brightness ELV trailing edge.
SPECIFICATION
static colors PINK VIOLET LIGHT BLUE SPRING GREEN YELLOW GOLDEN YELLOW AMBER RED GREEN BLUE
lumen output 460 / foot 295 / foot 575 / foot 760 / foot 290 / foot 728 / foot 420 / foot 270 / foot 240t / foot 420 / foot beam spread 60° - 120° LEDs per foot 14 color consistency 3-step MacAdam Ellipse / CRI ≥ 84 lifetime > 70,000 hours / L70 or better
input voltage Universal 120–277V AC power consumption 6.1 W
dimensions [ L x W x H ] 12” x 1.65” x 1.75” 24” x 1.65” x 1.75” 46.8” x 1.65” x 1.75” weight 1 lbs. per foot housing extruded aluminum housing with tooled end caps lens etched polycarbonate mounting surface mounting with (+/– 15°) adjustable brackets (ADB2 option +/– 90°) operating temperature -10°C to 40°C junction temperature 60°C @ TA 25°C
interface dimmable to 3% full brightness, (ELV) electronic low-voltage trailing edge, synchronized w/ soft shut-off power supply integral Class II, electronic high-power factor 94%
certification ETL / cETL or CE standards UL-Class I / IES LM-79 / LM-80 environment dry, interior location / IP 20 installation http://tinyurl.com/jy9dawn warranty 5 year limited warranty (refer to website for details) Due to continuous development and improvements, specifications are subject to change without notice.
CATALOG NUMBER
ECVLX
model length color optics
ECVLX eCOVELINE XL 1 305 mm [ 12 in. ] PINK PINK ** 60 60º x 100° beam 2 610 mm [ 24 in. ] VIOL VIOLET ** 120 120° x 120º beam 4 1219 mm [ 46.8 in. ] LTBLU LIGHT BLUE ** SPGRN SPRING GREEN ** YELLW YELLOW ** GLDYW GOLDEN YELLOW ** AMBER AMBER ** RED RED ** ** Consult Factory (minimum order quantity) GRN GREEN ** BLUE BLUE **
Accessories (Indicate the quantity needed for each item.) REQUIRED: Starter Cable (SC6) and Terminator Cap (TCAP) for every run. Maximum Run Length = 80 feet
______BL Black Louvre ______SC6 6 ft. Starter Connection Cord ______EC12 12 in. Extension Cord ______ADB2 (+/– 90°) Adjustable Bracket ______TCAP Terminator Cap ______EC24 24 in. Extension Cord ______BEA Bracket Extension Arm ______EC06 6 in. Extension Cord ______EC60 60 in. Extension Cord
© 2016 Solid State Luminaires. p 877-SSL-GREEN . f 630-889-8106 3609 swenson ave., st. charles, il 60174. www.solidstateluminaires.com JF Rev. 916 Catalog Number
FEATURES & SPECIFICATIONS Notes INTENDED USE — For wall or ceiling mounting, vertical or horizontal. The WL combines digital LED lighting and controls technologies with high-performance optical design to offer the most advanced wall-mount luminaire for general ambient lighting applications. High-efficacy light engine delivers long life and excellent Type color, ensuring a superior quality lighting installation that is highly efficient and sustainable. CONSTRUCTION — Housing is roll formed from code-gauge steel. Refractor is retained in die cast ends providing secure installation and easy maintenance. Decorative die-cast end caps provide added durability. Finish: All metal parts are post-painted in white polyester powder coat for smooth, finished edges and uniform light distribution. Wall bracket & Surface Mount LED OPTICS — Impact modified linear faceted refractor. Optically engineered for superior light distribution and maximum efficacy. Crescent-shape linear faceted refractor system obscures and integrates individual LED images and uniformly washes fixture surface with light. ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality of illumination for extended service life. 90% LED lumen maintenance at 60,000 hours (L90/60,000). The WL4 LEDs have a CRI of 82. eldoLED driver options deliver choice of dimming range and choices for control, while assuring flicker-free, 4' low-current inrush, 89% efficiency and low EMI. LED Driver disconnect provided where required to comply with US and Canadian codes. CONTROLS — Optional nLight™ embedded controls continuously monitor system performance and allow for constant lumen management function. nLIGHT Lumen Management: Unique lumen management system (option N80) provides onboard intelligence that actively manages the LED light source so that constant lumen output is maintained over the system life, n preventing energy waste created by the traditional practice of over-lighting. ENABLED Integral occupancy control: Integrated occupancy sensors allow luminaire to power off or dim to 10% or 50% output when space is unoccupied. Fixture designed to fail on. The nES 7 is ideal for small rooms without obstructions or areas with primarily walking motion (e.g. corridors, stairwells). Additionally, the NES7ADCX includes an integrated photocell, which enables daylight harvesting. For rooms like restrooms and private offices or any space with obstructions, the nES PDT 7 dual technology sensor is recommended. The nES PDT 7 utilizes both PIR (passive infrared) and MicrophonicsTM technologies to detect occupancy. Wireless networking: XPointTM Wireless technology creates a mesh network to ensure communication between fixtures, sensors and wall stations facility-wide. This option provides superior lighting management capabilities including granular control, configuration and custom grouping. This option enables sensors that detect motion to wirelessly communicate to neighboring fixtures — whether on different floors in a stairwell, to a corridor or hallway — illuminating the desired path. LISTINGS — CSA certified to meet U.S. and Canadian standards. Suitable for damp location (excluding sensor option). Patents pending. DesignLights Consortium® (DLC) qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified. WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx NOTE: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 °C. Specifications subject to change without notice.
Capable Luminaire This item is an A+ capable luminaire, which has been designed and tested to provide consistent color appearance and out-of-the-box control compatibility with simple commissioning. • All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency • This luminaire is part of an A+ Certified solution for nLight® control networks when ordered with drivers marked by a shaded background* • This luminaire is part of an A+ Certified solution for nLight control networks, providing advanced control functionality at the luminaire level, when selection includes driver and control options marked by a shaded background* To learn more about A+, visit www.acuitybrands.com/aplus. *See ordering tree for details
LED WL4-LED Catalog Number FEATURES & SPECIFICATIONS Notes INTENDED USE — For wall or ceiling mounting, vertical or horizontal. The WL combines digital LED lighting and controls technologies with high-performance optical design to offer the most advanced wall-mount Type luminaire for general ambient lighting applications. High-efficacy light engine delivers long life and excellent color, ensuring a superior quality lighting installation that is highly efficient and sustainable. CONSTRUCTION — Housing is roll formed from code-gauge steel. Refractor is retained in die cast ends providing secure installation and easy maintenance. Decorative die-cast end caps provide added durability. Finish: All metal parts are post-painted in white polyester powder coat for smooth, finished edges and uniform light distribution. Wall bracket & Surface Mount LED OPTICS — Impact modified linear faceted refractor. Optically engineered for superior light distribution and maximum efficacy. Crescent-shape linear faceted refractor system obscures and integrates individual LED images and uniformly washes fixture surface with light. ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality WL2 of illumination for extended service life. 90% LED lumen maintenance at 60,000 hours (L90/60,000). The LEDs have a CRI of 82. 2' eldoLED driver options deliver choice of dimming range and choices for control, while assuring flicker-free, low-current inrush, 89% efficiency and low EMI. LED Driver disconnect provided where required to comply with US and Canadian codes.
CONTROLS — Optional nLight™ embedded controls continuously monitor system performance and allow nLIGHT for constant lumen management / compensation function. Lumen Management: Unique lumen management system (option N80) provides onboard intelligence that n actively manages the LED light source so that constant lumen output is maintained over the system life, ENABLED preventing energy waste created by the traditional practice of over-lighting. Integral occupancy control: Integrated occupancy sensors allow luminaire to power off or dim to 10% or 50% output when space is unoccupied. Fixture designed to fail on. The nES 7 is ideal for small rooms without obstructions or areas with primarily walking motion (e.g. corridors, stairwells). Additionally, the NES7ADCX includes an integrated photocell, which enables daylight harvesting. For rooms like restrooms and private offices or any space with obstructions, the nES PDT 7 dual technology sensor is recommended. The nES PDT 7 utilizes both PIR (passive infrared) and MicrophonicsTM technologies to detect occupancy. Wireless networking: XPointTM Wireless technology creates a mesh network to ensure communication between fixtures, sensors and wall stations facility-wide. This option provides superior lighting management capabilities including granular control, configuration and custom grouping. This option enables sensors that detect motion to wirelessly communicate to neighboring fixtures — whether on different floors in a stairwell, to a corridor or hallway — illuminating the desired path. LISTINGS — CSA certified to meet U.S. and Canadian standards. Suitable for damp location (excluding sensor option). Patents pending. DesignLights Consortium® (DLC) qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified. WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx NOTE: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 °C. Specifications subject to change without notice.
Capable Luminaire This item is an A+ capable luminaire, which has been designed and tested to provide consistent color appearance and out-of-the-box control compatibility with simple commissioning. • All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency • This luminaire is part of an A+ Certified solution for nLight® control networks when ordered with drivers marked by a shaded background* • This luminaire is part of an A+ Certified solution for nLight control networks, providing advanced control functionality at the luminaire level, when selection includes driver and control options marked by a shaded background* To learn more about A+, visit www.acuitybrands.com/aplus. *See ordering tree for details
LED WL2-LED Luminaire Type: Catalog Number (autopopulated):
Gotham Architectural Downlighting LED Downlights 6” Evo® Non-Conductive Shower Light
Solid-State Lighting
FEATURES OPTICAL SYSTEM • Tested according LM-79 and LM-80 standards • Face plate made of impact-modified acrylic for excellent durability and light • Overload and short circuit protected transmission • 2.5 SDCM; 85 CRI typical, 90+ CRI optional • “Dead front” shower light for added safety LISTINGS • White painted flange • Fixtures are CSA certified to meet US and Canadian standards; wet location, MECHANICAL SYSTEM covered ceiling • 16-gauge galvanized steel construction; maximum 1-1/2” ceiling thickness • IP65 rated; suitable for steam room applications • Telescopic mounting bars maximum of 32” and minimum of 15”, preinstalled, WARRANTY 4” vertical adjustment • 5-year limited warranty. Complete warranty terms located at: • Toolless adjustments post installation www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx • Junction box capacity: 8 (4 in, 4 out ) 12AWG rated for 90°C • Light engine and driver accessible through aperture Note: Actual performance may differ as a result of end user environment and application. ELECTRICAL SYSTEM All values are design or typical values, measured under laboratory conditions at • Fully serviceable and upgradeable lensed LED light engine 25° C. • 70% lumen maintenance at 60,000 hours ORDERING INFORMATION ORDERING A+ Capable options indicated by this color background.
EXAMPLE: EVO 35/10 6DFR MVOLT EZ1
Series Color temperature Nominal lumen values Aperture Trim style Voltage EVO 27/ 2700 K 10 1000 lumens 35 3500 lumens 6 DFR Dead (non-conductive) front regressed MVOLT 30/ 3000 K 15 1500 lumens 40 4000 lumens DFD Dead (non-conductive) front drop 120 35/ 3500 K 20 2000 lumens 45 4500 lumens DFRAMF Dead (non-conductive) front regressed, 277 40/ 4000 K 25 2500 lumens antimicrobial finish 347 30 3000 lumens DFDAMF Dead (non-conductive) front drop, antimicrobial finish
Driver1 Options EZ10 eldoLED 0-10V ECOdrive. Linear dimming to 10% min. SF Single fuse. Specify 120V or 277V. EZ1 eldoLED 0-10V ECOdrive. Linear dimming to 1% min. ELR4 Emergency battery pack with remote test switch EZB eldoLED 0-10V SOLOdrive. Logarithmic dimming to <1%. NPS80EZ3 nLight® dimming pack controls 0-10V eldoLED drivers. EDAB eldoLED SOLOdrive DALI. Logarithmic dimming to <1%. NPS80EZER3,5 nLight® dimming pack controls 0-10V eldoLED drivers. ER EDXB eldoLED POWERdrive DMX with RDM (remote device management). Square Law controls fixtures on emergency circuit. dimming to <1%. Includes termination resistor. Refer to DMXR Manual. BGTD Bodine generator transfer device EXA1 XPoint Wireless, eldoLED 0-10V ECOdrive. Linear dimming to 1%. Refer to CRI90 High CRI (90+) XPoint tech sheet. CP6 Chicago plenum EXAB XPoint Wireless, eldoLED 0-10V SOLOdrive. Logarithmic dimming to <1%. RRL__ RELOC®-ready luminaire. Provides compatibility with Lithonia Refer to XPoint tech sheet. RELOC system. Access above ceiling required. ECOS22,3 Lutron® Hi-Lume® 2-wire forward-phase driver. Minimum dimming level 1%. Minimum lumen 1000/Maximum lumen 3000. ECOS32,3 Lutron® Hi-Lume® 3-wire or EcoSystem® dimming driver. Minimum dim- ming level 1%. Minimum lumen 1000/Maximum lumen 4500.
ACCESSORIES order as separate catalog numbers (shipped separately) SCA6 Sloped ceiling adapter. Degree of slope must be specified (5D, 10D, 15D, 20D, 25D, 30D). Ex: SCA6 10D. Refer toTECH-190 . CTA4-8 YK Ceiling thickness adapter (extends mounting frame to accommodate ceiling thickness up to 5”). Adds ~4” to fixture height. ISD BC 0-10V wallbox dimmer. Refer to ISD-BC.
EVO-6-Shower GOTHAM ARCHITECTURAL DOWNLIGHTING | P 800.315.4982 | gothamlighting.com PAGE 1 OF 4 © 2011-2016 Acuity Brands Lighting, Inc. All Rights Reserved. Rev. 10/12/16. Specifications subject to change without notice. BUY AMERICAN ACT OF 2009 COMPLIANT FINELITE High Performance 2" Aperture (HP-2) - Wall Mount Indirect/Direct
stry B u e d s n t Date I 1010 YearYear LED Warranty Project
Type
Comments
Bottom Glow Diffuser (Shown)
DESCRIPTION High Performance 2" Aperture Wall Mount Indirect/Direct (HP-2 WM-ID) is a patented, linear LED luminaire with Flush, Top Glow™ and Bottom Glow™ options for up- and downlight. The micro shape delivers excellent performance using an advanced optical design and mid-power LEDs to achieve 90% of initial light output at 100,000 hours.
Top Glow Diffuser (Standard)
0.5" 0.5" 0.2"
4 3/4" 4 3/4" Tailored Lighting
0.2" 2 1/4" 2 1/4" 10 working days Bottom Glow Diffuser Flush Uplight and (Optional) Downlight Diffuser (Standard) DIMENSIONS & LIGHT ENGINE BOTTOM GLOW DIFFUSER TAILORED LIGHTING A glare-free experience is attained with mid-power The optional Bottom Glow diffuser adds a clean Any length greater than 2 feet, in increments down LEDs and a precise diffuser to eliminate pixilation. line of light along the downlight element. to 1/16th-inch (± 1/32") and 90-degree mitered corners in a single plane.
ORDERING GUIDE Sample Number: HP-2 WM-ID - 32'- S - H - 8 - 35 - TG - F - 120V - MB - SC - OBO
HP-2 WM-ID
Finelite Series HP-2 WM-ID Length (Minimum 2', increments accurate to 1/16th" (± 1/32"), standard) Uplight Output (S - Standard, B - Boosted Standard,
H - High, V - Very High) ©
2 0 1
Downlight Output (S - Standard , B - Boosted Standard, 6
F I N
H - High, V - Very High) E L I T
LED CRI (8 - 80 CRI min (standard), 9 - 90 CRI min) E ,
I N
LED Color Temperature (30 - 3000K, 35 - 3500K, 40 - 4000K) C .
A L
Uplight Diffuser Option (TG - Top Glow (standard), F - Flush) L
R I Downlight Diffuser Option (F - Flush (standard), BG - Bottom Glow) G H T S
Voltage (120V, 277V) R E S
Mounting (MB - Mounting Bracket) E R V E
Circuiting (SC - Single Circuit, DC - Dual Circuit)* D .
F
Integrated Sensor (OBO - Occupancy Sensor, OBD - Daylight) o r m
* Contact factory for switching options. Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S C T K 0 1 1
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • 510 / 441-1100 • Fax: 510 / 441-1510 • www.finelite.com 6 .
0 8 / 1
Due to continuing product improvements, Finelite reserves the right to change specifications without notice. Please visit www.finelite.com for most current data. 6 LED Frosted Highbay Fixture (18,000 Lumens)
Features • Frosted lens to reduce glare • DLC Premium 4.0 under Nuwave Model • Instant on to full brightness number 52000 and 52001 • Energy efficient • UL, RoHS and FCC certified • Wide light distribution • NSF certified-Splash zone/Non-Food zone • • High efficacy up to 137 lumens per watt Input voltage 120-277V or 347-480V • Light weight for easy installation • Workable voltage at 90-305V or 312-528V • Lower maintenance costs • 0-10 V DC dimming standard
• Available 3000K, 4000K, and 5000K Applications Available Options color temperatures • Warehouses • 6' cord and plug • IP65 Rated for wet locations • Storage areas • Griplock suspension • Operating temp -40°C - +60°C • Food processing system -40°F - +140°F plants • • Stainless steel • Dimensions 21.6" x 21.6" x 5.20" Cold storage • Convention centers wire guard • Field replaceable modular driver • Airports • Occupancy sensor/ • LM79/80 report and TM21 data available • Healthcare facilities Daylight harvesting • Superior heat management yields • Manufacturing plants • Pendant hook 60,000 hours life • Retail stores • 7 year warranty • Agriculture
Items Stocked in Illinois Warehouse Color Lumens Wattage Model# SKU Lumens CRI Weight (lbs) Watts IES Per Watt Temp (K) Equivalent File
52000 HB-18L-40K-UL 18,025 >80 14.5 4000 136 133 400 HID
400 HID 52001 HB-18L-50K-UL 18,704 >80 14.5 5000 136 137
® US
1795 N Butterfield Rd Libertyville, IL 60048 www.alsetled.com Customer Service 1-800-689-2573 Rev 15 8-26-16 Catalog Number
FEATURES & SPECIFICATIONS Notes INTENDED USE — The BLT Best-in-Value Low Profile LED luminaire features a popular center basket design that offers a clean, versatile style and volumetric distribution. High efficacy LED light engines deliver energy Type savings and low maintenance compared to traditional sources. An extensive selection of configurations and options make the BLT the perfect choice for many lighting applications including schools, offices and other commercial spaces, retail, hospitals and healthcare facilities. The low profile BLT design (2-9/16") also makes it an excellent choice for renovation projects. BLT Series LED BLT Tunable White is perfect in classrooms and educational settings as it allows the light color temperature to be adjusted to the optimal light level for student tasks such as reading or test taking. CONSTRUCTION — BLT enclosure components are die-formed for dimensional consistency and painted after fabrication with a polyester powder paint for improved performance and protection. The reflector is finished with a high reflective matte white powder paint for improved aesthetics and 2BLT Tunable White increased light diffusion. End plates contain easy-to-position integral T-bar clips for securely attaching the luminaire to the T-grid. 2' x 2' For additional T-grid security, optional screw on T-bar clips are available. LED Diffusers are extruded from impact modified acrylic for increased durability. Injection molded diffuser light traps add a finished look to the diffuser ends and help seal the diffuser to the housing end plates. Optional diffuser trim rings provide an attractive mounting for integral sensors as well as adding a decorative element to the luminaire aesthetics. LED boards are accessible from below; driver is accessible from the plenum. OPTICS — Volumetric illumination is achieved by creating an optimal mix of light to walls, partitions and vertical and horizontal work surfaces – rendering the interior space, objects and occupants in a more balanced, complimentary luminous environment. High performance extruded acrylic diffusers conceal LEDs and efficiently deliver light in a volumetric distribution. Four diffuser choices available - curved and square designs with linear prisms or a smooth frosted finish. ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality of illumination for extended service life. 70% LED lumen maintenance at 60,000 hours (L70/60,000). Tunable White GPHD eldoLED driver options deliver choice of dimming range, and choices for control, while assuring flicker-free, • Gamut: One dimensional Warm-Cool low-current inrush, 89% efficiency and low EMI. • Path: Direct 3000K to 5000K (Productivity Range) Integrated nLight®controls make each luminaire addressable — allowing it to digitally communicate with • Handle: Two Natural Language Handles: Intensity and CCT other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply • Data: nLight with nTune technology for both handles of control connect all the nLight enabled control devices and the BLT luminaires using standard Cat-5 cabling. Unique plug-and-play convenience as devices and luminaires automatically discover each other and self-commission. Driver disconnect provided where required to comply with US and Canadian codes. 580 Mainstream Dynamic Tunable White with nTune Technology: Tunable white nTune™ is an all digital light 2700 3000 color temperature control within an nLight enabled luminaire. This brings tunable white lighting control into 2200 2000 3500 590 1800 the mainstream with repeatable, consistent results in an economical luminaire form and system already 4000 4500 familiar to schools. Designers and facility operators are granted the freedom to tie scenes to specific activities 5000 or to complement colors or materials within a visual environment. nTune™ allows color temperature settings 5700 through the Productivity Range of 3000K-5000K. Refer to the Programming User’s Guide for instructions on 6500 customizing to your application with SensorView™. 10000 A Integrated Sensor (nLight Wired Networking): This sensor is nLight-enabled, meaning it has the ability to communicate over an nLight network. When wired, using CAT-5 cabling, with other nLight-enabled sensors, power packs, or WallPods, an nLight control zone is created. Once linked to a Gateway, directly or via a Bridge, the zone becomes capable of remote status monitoring and control via SensorView software. See page 2 for the nLight sensor options. INSTALLATION — The BLT’s low profile design of only 2-9/16" provides increased installation flexibility especially in restrictive plenum applications. The BLT fits into standard 15/16" and narrow 9/16" T-grid ceiling systems. Suitable for damp location. A Productivity Range 3000K to 5000K For recessed mounting in hard ceiling applications, Drywall Grid Adapters (DGA) are available as an accessory. See Accessories section. LISTINGS — CSA Certified to meet U.S. and Canadian standards. IC rated. WARRANTY — 5-year limited warranty. Complete warranty terms located at Capable Luminaire www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx This item is an A+ capable luminaire, which has been designed and tested to NOTE: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 °C. provide consistent color appearance and out-of-the-box control compatibility with Specifications subject to change without notice. simple commissioning. • All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency • This luminaire is part of an A+ Certified solution for nLight® control networks when ordered with drivers marked by a shaded background* • This luminaire is part of an A+ Certified solution for nLight control networks, providing advanced control functionality at the luminaire level, when selection includes driver and control options marked by a shaded background* To learn more about A+, visit www.acuitybrands.com/aplus. *See ordering tree for details
LED 2BLT-2X2-NTUNE BUY AMERICAN ACT OF 2009 COMPLIANT FINELITE High Performance 2" Aperture (HP-2) - Direct
stry B u e d s n t I 101 0 Date Year LED Warranty Project Signal White is standard finish
Type
Comments
Bottom Glow Diffuser (Shown)
DESCRIPTION High Performance 2" Aperture Direct (HP-2 D) is a patented, linear LED luminaire with Flush and Bottom Glow™ options for the downlight. The micro shape delivers excellent performance using an advanced optical design and mid-power LEDs to achieve 90% of initial light output at 100,000 hours.
4" 4" Tailored Lighting
0.2" 10 working days 2 1/4" 2 1/4" Flush Downlight Diffuser Bottom Glow Diffuser (Standard) (Optional)
DIMENSIONS & BOTTOM GLOW FLEXIBLE MOUNTING TAILORED LIGHTING The optional Bottom Glow diffuser adds a The flexible mounting bracket adjusts the suspension Any length greater than 2 feet, in increments down clean line of light along the downlight element. points along the length of the luminaire to accommo - to 1/16th-inch (± 1/32") and 90-degree mitered date existing architecture. Suspension points adjust corners in a single plane. up to 2' in from the end of 8'or 12' luminaire lengths and up to 1' in on shorter lengths.
ORDERING GUIDE Sample Number: HP-2 D - 32' - H - 8 - 35 - F - 120V - FA - SC - C1 - OBO
HP-2 D
Finelite Series HP-2 D
Length (Minimum 2', increments accurate to 1/16th" (± 1/32"), standard) ©
2 0 1
Light Output ( S - Standard , B - Boosted Standard, H - High, V - Very High ) 6
F I LED CRI (8 - 80 CRI min (standard), 9 - 90 CRI min) N E L I LED Color Temperature (30 - 3000K, 35 - 3500K, 40 - 4000K) T E ,
I N
Downlight Diffuser (F - Flush (standard), BG - Bottom Glow) C .
A
Voltage (120V, 277V) L L
R I
Mounting (FA - Fully Adjustable, FM - Flexible Mounting) G H T Circuiting (SC - Single Circuit)* S
R E S
Ceiling Type (C1 - 1" T-Bar, C2 - 9/16" T-Bar, C3 - screw slot, C4 - hard ceiling) E R V
Integrated Sensor (OBO - Occupancy Sensor, OBD - Daylight) E D .
F o r m
*Contact factory for switching options. Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S C T K 0 1 1
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • 510 / 441-1100 • Fax: 510 / 441-1510 • www.finelite.com 9 .
0 8 / 1
Due to continuing product improvements, Finelite reserves the right to change specifications without notice. Please visit www.finelite.com for most current data. 6 15774 Gateway Circle PH: 714.259.9959 Wila By Ledra Brands Inc. www.wilalighting.com Tustin, CA 92780 FAX: 714.259.9969
Job Name: Contact:
Ordering Code: Fixture Type:
610 Recessed LED OpticLites H Description The 610 recessed LED downlight with Chroma technology provides energy efficient light using a cold remote phosphor LED by XICATO® for industry-best fixture-to-fixture color consistency. 610 includes a German hand-blown, cylindrical, opal glass shade that is attached to the trim and is 5” in length from the ceiling. GH
Housing All configurations are of modular construction consisting of integral junction box from 16-gauge galvanized steel, integral driver, quick connect whip and the Module Assembly. The New CO Construction mounting option provides for ceiling fitting plate installation independent of the Module Assembly, allowing the finish and closing of the ceiling. 27” long steel mounting bars Ceiling Cut-Out Diameter (MB27) are supplied for NC, IC, ICAT, or CP mounting options.
MS-3 Mounting System Patented 3-point bayonet latch mounting system consists of die-cast magnesium trim ring and mounting ring with adjustable throat to accommodate up to a 2” ceiling thickness. Mounting ring incorporates integral yoke and box from 16-gauge galvanized steel for easy optical assembly. W
Listings - ETLus Listed to UL1598, cETL Listed to CSA C22.2 #250.0 - Type IC with IC, ICAT, or CP box options. L - Suitable for dry and damp locations. - Made in the USA - meets the requirements of the Buy American provision within the ARRA. New Construction Dimensions
CO H GH L W 5-5/8” 3-7/8” 5” 13-7/8” 7-7/8” [142mm] [98mm] [127mm] [354mm] [200mm]
Ordering Codes
Follow the steps to specify your fixture, example: 610 - 5 - XTM19 - 13LM - 35K - 98 - 277 - 10V
Series Aperture LED Delivered Lumen CCT CRI Voltage Dimming
610 5 5” XTM19 07LM 595 lm 27K 2700K 83 83 CRI 120 120V 10V standard 0-10V dimming to 10% 10LM 850 lm 30K 3000K 981 98 CRI 277 277V LUDA Lutron Hi-lume/EcoSystem A-Series -to 1% 3 13LM 1105 lm V30K 3000K Vibrant LUDH Lutron EcoSystem H-Series -to 1% 4 20LM 1700 lm 35K 3500K DIM10 eldoLED 0-10V dimming to 1% 4 30LM 2550 lm 40K 4000K DIM10Z eldoLED 0-10V dimming to zero (0.1%) 4 40LM1 3400 lm B27K2 2700K Beauty DALI eldoLED DALI dimming to 1% DALIZ4 eldoLED DALI dimming to zero (0.1%)
Notes
1. 98 CRI not available for 40LM. 2. B27K Beauty Series is only associated with 93 CRI and available for 07LM, 10LM and 13LM only. 3. LUDH not available for 07LM and 10LM. 4. DIM10, DIM10Z, DALI, DALIZ not available for 40LM. Available at 85% Lumen output for 30LM and 20LM (98 CRI).
QuikShip options on product webpage for download
In a continuing effort to offer the best product possible we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. v.6.17.16 610 Page 1 of 5 J6.1.24 ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT • 1000 lumen unit provides comparable light output to a 75W PAR30 halogen, DESIGNER COVE™ 2000 lumen unit provides output similar to a 39W PAR30 Metal Halide; all while utilizing less energy and having a rated life of 50,000 hours 1000/2000 Lumen LED • No harmful ultraviolet or infrared wavelengths OPEN APERTURE, White Trim Flange • No lead or mercury 1, 2 & 3 Head LED Units PRODUCT SPECIFICATIONS Electrical LED Light Engine: High output LED arrays provide outstanding reliability, performance and color quality/consistency • 2700K, 3000K, 3500 or 4000K color temperatures • 80 Type Cat. No. CRI minimum • Consistent fixture-to-fixture color temperature that is within 3 MacAdams ellipses Dimming: Dimmable via 0-10V controller • For a list of compatible dimmers see LED-DIM LED Driver: Universal driver accommodates 120V to 277V input volts AC at 50/60Hz • Power factor >0.9 • Easily replaceable from below or above the ceiling. Life: Rated for 50,000 hours at 70% lumen maintenance Project: Operation Temperature: -40º to 45º C Notes: Mechanical LED fixture head: Cast aluminum housing is removable for ease of maintenance and DIMENSIONS provides interchangeability of beam distributions and color temperatures • Twist and locks securely into place • LED fixture heads can be ordered and shipped separately from rough-in housing • Accessory louver maybe combined with one (1) accessory color filter 8-1/8˝ Adjustability: Yoke assembly allows 360º rotation and up to 75º tilt of lamp housing and features rotation and tilt locking • Yoke features 2” vertical adjustment allowing fixture head to be extended below ceiling 8-3/4˝ Housing: Heavy gauge cold rolled steel with white or black finish • Universal housing design installs in suspended grid, plaster or drywall • Heat sink conducts heat away from LED light engine • Drivers are accessible from above and below ceiling • Light engine and driver can be upgraded to accommodate future technology improvements • Active ‘A’ cooling (2000 lumen only) • Rough-in housing can be ordered separately from fixture ‘A’ CEILING CUT-OUT heads, see Individual Component Ordering Information below. ‘B’ ‘B’ FLANGE Mounting Bracket: Mounting brackets have 3” vertical adjustment and accept propri- etary TRU-LOCK bar hangers, 1-½˝ C-channel and flat linear bars (order as accessories) or 1-½˝ EMT, ¾˝ and 1-½˝ lathing channel (by others) ● One-piece Tru-Lock bar hangers LED fixture heads can have integral T-bar locking screws and alignment notches for locating and locking fixture be ordered and in the center or ¼” tile increments shipped separately Trim: All units are furnished with a heavy gauge white baked enamel trim from rough-in housing. Labels and Listings ‘C’ • UL listed for dry/damp locations • UL and cUL, RoHS compliant • EMI complies with FCC 47, Part 15, Class A • Energy Star Qualified of eiling ut-out lange rim im • I.B.E.W. Union made • ARRA Compliant eads 1 8-1/4˝ x 8-1/4˝ 9˝ x 8-7/8˝ 16˝ Warranty: 5 years when used in accordance with manufacturing guidelines. Product specifications subject to change without notice. 2 8-1/4˝ x 15-7/8˝ 9˝ x 16-1/2˝ 23-3/4” 3 8-1/4˝ x 23-3/4˝ 9˝ x 24-3/8˝ 31-1/2˝ COMPLETE UNIT ORDERING INFORMATION: (Use when ordering a complete fixture; rough-in, fixture heads, options and accessories) Example: DCS30-NN-10302-WH2 Example: HB-TL Cat. # Beam Spread/ Lumens Color Voltage Finish Generation Options Accessories One Per Lamp Temp. DCS30 2 HB-TL DCS30 S Spot 10 27 2700K 1 120V WH White ***F Fuse and Fuse Holder Two 25˝ Tru-Lock Grid Ceiling Bar Hangers, Pair HB-28 Two 28˝ C-Channel Bar Hangers, Pair 1, 2, 3-Lamp LED, 1000 Lumens (Where *** = voltage) 30 3000K 2 277V BL Black HB-52 Two 52˝ C-Channel Bar Hangers, Pair Designer Cove, N Narrow Flood 20 † 35 3500K 3 347V CP Chicago Plenum LB-27 Two 27˝ Linear Bar Hangers, Pair PAR30 Size F Flood 2000 Lumens †LDI Lumen Depreciation Indicator 40 4000K T569BL Louver - 3¾” Dia. w/ ½” Sq. Cells T561 Med. Pink Color Filter INDIVIDUAL COMPONENT (Use when ordering rough-in housing, fixture heads, T562 Warm Red Color Filter ORDERING INFORMATION: options and accessories separately) T563 Daylite Blue Color Filter T564 Med. Blue Color Filter Example: DCSR303-102-WH-2 Example: DCSH30N-1030-BL-2 T565 Med. Amber Color Filter T566 Med. Green Color Filter Rough-In Lumens Voltage Finish Generation Options Lamp Head/ Lumens Color Finish Generation Beam Spread Temp. T5677 Prismatic Spread Lens T5678 Linear Spread Lens 2 2 T5619 Color Correction Lens DCSR301 10 1 120V WH White ***F Fuse & Fuse Holder DCSH30S 10 1000 27 WH T5621 Uniformity Lens White 1-Lamp LED, 1000 2 277V BL Black (Where *** = voltage) Spot LED Head Lumens 2700K T5623 High Output Uniformity Lens PAR30 Size Rough-in Lumens BL 3 347V †CP Chicago Plenum DCSH30N 20 2000 30 20 Lumens 3000K Black Not for use with Chicago Plenum or 347V DCSR302 †LDI Lumen Depreciation Narrow Flood 2-Lamp LED, 2000 Not for use with any other accessories. Lumens LED Head 35 PAR30 Size Rough-in Indicator 3500K DCSR303 DCSH30F 40 3-Lamp LED, Flood LED 4000K PAR30 Size Rough-in Head
1300 South Wolf Road • Des Plaines, Illinois 60018 † Consult Factory for Availability PHONE 800-367-5866 • FAX 888-708-6578 03/15 Rev.2 www.junolightinggroup.com Catalog Number
FEATURES & SPECIFICATIONS Notes INTENDED USE — The VT Series LED combines digital LED lighting and controls technologies with patented high-performance optical design to offer the most advanced luminaire for general-ambient lighting Type applications. High-efficacy light engine delivers long life and excellent color, ensuring a superior quality lighting installation that is highly efficient and sustainable. CONSTRUCTION — Rugged, one-piece cold-rolled steel reflector assembly with embossed facets. Coated polyester powder-paint after fabrication. VT Series LED Rigid structure with ballast box and end plates. End plates include integral T-bar clips. Impact-modified acrylic prismatic refractor. Luminaires may be mounted end-to-end and continuously wired. OPTICS — Volumetric illumination is delivered by creating an optimal mix of light to walls, partitions, VTL vertical and horizontal work surfaces — rendering the interior space, objects and occupants in a more balanced, complementary luminous environment. 1' X 4' Light distribution is carefully controlled at high angles, providing just enough luminous flux to create the LED volumetric effect. Linear faceted reflector cavity softens and distributes light into the space while minimizing luminous contrast between the fixture and ceiling. ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality of illumination for extended service life. 90% LED lumen maintenance at 60,000 hours (L90/60,000). Optional integrated nLight®controls make each luminaire addressable - allowing it to digitally communicate with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply connect all the nLight enabled control devices and the VT Series LED luminaires using standard CAT-5 cabling. Unique plug-and-play convenience as devices and luminaires automatically discover each other and self-commission. Lumen Management: Unique lumen management system (option N80) provides onboard intelligence that INDUSTRY RECOGNITION/AWARDS actively manages the LED light source so that constant lumen output is maintained over the system life, preventing the energy waste created by the traditional practice of over-lighting. Step-level dimming option allows system to be switched to 50% power for compliance with common energy codes while maintaining fixture appearance. eldoLED driver options deliver choice of dimming range, and choice of control, while assuring flicker-free, 2012 RECOGNIZED 2011 ARCHITECTURAL SSL PRODUCT low current inrush, 89% efficiency and low EMI. PRODUCT INNOVATION AWARD Ballast disconnect provided where required to comply with US and Canadian codes. INSTALLATION — Drivers and internal components accessed via plenum. Driver tray may be removed from fixture during service. Suitable for damp location. Maintenance: LED boards include plug-in connectors for easy replacement or servicing. LISTINGS — CSA Certified to meet U.S. and Canadian standards. DesignLights Consortium® (DLC) Premium qualified product. Not all versions of this product may be DLC Premium qualified. Please check the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified. Tested to LM80 standards. IC rated. Protected by one or more of US Patent Nos. 7,229,192; D541,467; D541,468; D544,633; D544,634; D544,992. D544,933 and additional patents pending. WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx Note: Specifications subject to change without notice. Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 °C.
Capable Luminaire This item is an A+ capable luminaire, which has been designed and tested to provide consistent color appearance and out-of-the-box control compatibility with simple commissioning. • All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency • This luminaire is part of an A+ Certified solution for nLight® control networks when ordered with drivers marked by a shaded background* • This luminaire is part of an A+ Certified solution for nLight control networks, providing advanced control functionality at the luminaire level, when selection includes driver and control options marked by a shaded background* To learn more about A+, visit www.acuitybrands.com/aplus. *See ordering tree for details
LED VTL-1X4 Type: Approved: Fixture: Project:
The COVELINE XL is a powerful, versatile cove luminaire delivering over 1000 lumens per foot. COVELINE XL COVELINE XL comes in a 1 ft, 2 ft, or 4 ft nominal lengths and 24K, 27K, 3K, 35K or 4K color temperatures. The housing is constructed of extruded aluminum with tooled end caps and is IP20 rated for interior use only. Features Plug N’ Play connectors for easy installation. Flicker free dimmable to 3% full brightness with ELV trailing edge dimming.
SPECIFICATION
color temperature 2400K (consult factory) 2700K 3000K 3500K 4000K
beam spread 60° - 120° lumen output 550 per foot 915 per foot 930 per foot 950 per foot 1025 per foot LEDs per foot 22 color consistency 3-step MacAdam Ellipse / CRI ≥ 84 lifetime > 70,000 hours / L70 or better
input voltage Universal 120–277V AC power consumption 11W
dimensions [ L x W x H ] 12” x 1.65” x 1.75” 24” x 1.65” x 1.75” 46.8” x 1.65” x 1.75” weight 1 lbs. per foot housing extruded aluminum housing with tooled end caps lens etched polycarbonate mounting surface mounting with (+/– 15° standard), adjustable brackets (ADB2 +/- 90°) operating temperature -20°C to 40°C junction temperature 65°C @ TA 25°C
interface dimmable to 3% full brightness, (ELV) electronic low-voltage trailing edge, synchronized w/ soft shut-off power supply integral Class II, electronic high-power factor 94%
certification ETL / cETL or CE standards UL-Class I / IES LM-79 / LM-80 environment dry, interior location / IP 20 installation http://tinyurl.com/jy9dawn warranty 5 year limited warranty (refer to website for details) Due to continuous development and improvements, lab test details and specifications are subject to change without notice.
CATALOG NUMBER
CVLX
model length temperature optics
CVLX COVELINE XL 1 305 mm [ 12 in. ] 24K 2400K ** 60 60°x100° beam 2 610 mm [ 24 in. ] 27K 2700K 120 120ºx120° beam 4 1219 mm [ 46.8 in. ] 3K 3000K 35K 3500K 4K 4000K **Consult factory (minimum order quantity)
Accessories (Indicate the quantity needed for each item.) REQUIRED: Starter Cable (SC6) and Terminator Cap (TCAP) for every run. Maximum Run Length = 60 feet
______BL Black Louvre ______SC6 6 ft. Starter Connection Cord ______EC12 12 in. Extension Cord ______ADB2 (+/– 90°) Adjustable Bracket ______TCAP Terminator Cap ______EC24 24 in. Extension Cord ______BEA Bracket Extension Arm ______EC06 6 in. Extension Cord ______EC60 60 in. Extension Cord
© 2016 Solid State Luminaires. p 877-SSL-GREEN . f 630-889-8106 3609 Swenson Ave., St. Charles, IL 60174. www.solidstateluminaires.com JO Rev. 916 6000 Lytespan, Basic, 1 Circuit Track
Page 1 of 4
Project: Catalog No: Mfg: Location: Fixture Type: Qty: Notes: Lamps:
2 3
1/16" 45-1/16" 3/4" 6000NWH 6008NBK 6054NWH 3/32" 93-1/16" 4 141-1/16" 6000NBK 6008NAL 6054NBK 5 6000NAL 6046NWH 6062WH 6001NWH 6046NBK 6062BK 6 1 1-5/32" 6001NBK 6048NWH 6063WH Plain Track 6001NAL 6048NBK 6063BK 21-1/16" 6002NWH 6049NWH 6063NAL 2-23/32" 45-1/16" 3/32" 3/32" 95-29/32" 6002NBK 6049NBK 6087 93-1/16" 7 8 9 6002NAL 6050NWH 6088 6003NWH 6050NBK 6089 6003NBK 6051NWH 7480 Individual Track Joiner Track 6003NAL 6051NBK 7480AL 6004NWH 6052NWH 7481 23-25/32" 6004NBK 6052NBK 7582 47-25/32" 96" 96" 3/32" 95-25/32" 6004NAL 6053NWH 7582AL 6008NWH 6053NBK 7584 7586
Individual Track Joiner Track Joiner Track Ordering guide
Individual Track Joiner Track Plain Track Includes Live End Feed Connector Includes Mini Coupler Includes Dead End Finishes 2' Catalog No. 4’ Catalog No. 8’ Catalog No. 8’ Catalog No. 4’ Catalog No. 6’ Catalog No. 8’ Catalog No. 12’ Catalog No. Matte White 6000NWH 6001NWH 6002NWH 6003NWH 6004NWH 6006NWH 6008NWH 6012NWH Matte Black 6000NBK 6001NBK 6002NBK 6003NBK 6004NBK 6006NBK 6008NBK 6012NBK Met Aluminum 6000NAL 6001NAL 6002NAL 6003NAL 6004NAL 6006NAL 6008NAL 6012NAL
Features Mounting Finish Basic Lytespan is a one circuit electrical distribution The track may be surface or stem mounted All painted finishes are baked enamel. system designed to support and supply all Lytespan (see pages 2, 3, and 4) or installed in a recessed lighting units in a flexible manner. The track can be housing (see Specification sheet 7515). The track Labels installed individually in straight runs or in a variety is not intended to be cable mounted. All lengths of patterns. can be field cut. cUL; I.B.E.W 1. Basic Lytespan Track: 6063-T5 structural aluminum extrusion. Electrical 2. Track Mounting Clips: 0.024 Spring steel, in black or white; order separately. Capacity is 20 amps. at 120 volts per branch circuit 3. Toggle Bolt & Screws: furnished with (2400 watts incandescent load). The track units are track units. polarized and continuously grounded throughout. 4. Conductor (2): copper 12 ga. equivalent. “U” Electrical conductors are concealed in a insulating shape provides reliable contact with connectors. liner. Intended for wiring to branch circuit building 5. Insulating Liner: 0.032" wall, high wire with ground. All wiring must be in accordance temperature thermoplastic. with National and Local Codes. 6. Polarity Bead: identifies the neutral conductor. 7. Live End: molded thermoplastic. Contains Mechanical contacts for power supply leads. 8. Dead End Cover: molded thermoplastic. Track units plug together and lock securely to prevent 9. Mini Coupler: connects track units mechanically accidental separation. Lytespan lighting units can be and electrically. attached at any point along the track.
© 2015 Koninklijke Philips N.V. All rights reserved. philips.com/luminaires
6000 10/15 Project: Track Location: Cat.No:
Type: Alcyon LED Lamps: Qty: Notes:
Vertical cylinder, LLAV11, 15 W / 1000 lm Alcyon LED Vertical Cylinders are ideal for display, accent and task lighting and offer higher efficiency than incandescent or halogen sources leading to energy savings with no ultraviolet or infrared radiation. Alcyon provides concentrated light which dramatically draws interest to objects and elements in a space.
Fixture example: LLAV1130AL Accessories example: LLA11SNBK
Series Lumens CRI/CCT* Adapter Finish Options Series Finish LLAV 11
LLAV 11 15W 27 80CRI/2700K — Lightolier WH White — no options LLAV11AH WH White Alcyon LED 1000 lm 30 80CRI/3000K H Halo AL Alum. CW CrispWhite1 Accessory holder AL Aluminum vertical 40 80CRI/4000K J Juno BK Black with spring BK Black cylinder 927 90CRI/2700K P Prospec2 LLA11SN WH White 930 90CRI/3000K1 Compatible snoot BK Black LLAV11 LS Linear Spread Reflector example: LLAV11RS Compatible SY Symmetrical Spread diffusion filters SF Soft Focus Series Lumens Reflector FR Frosted Etched LLAV 11 Compatible color filters/gels provided by others
LLAV 11 Compatible with 10 W / 600 lm, RNS 10° Narrow Spot LLAHCA11 Compatible hex cell louver Alcyon LED 15 W / 1000 lm & 28 W / 2000 lm RS 18° Spot (matte black) vertical RNF 24° Narrow flood 1. CrispWhite (CW) is only available with 90CRI / cylinder RF 36° Flood 3000K CCT (930). 2. Prospec is only offered in White (WH) and Black (BK).
Features Mounting 1. LED board: COB LED. 8. Driver housing: Extruded aluminum Compatible with all Monopoint, Multipoint, 2. Integrated housing heat sink: housing with die-cast aluminum covers. recessed track, suspension track, suspension die-cast aluminum maintains LED junction 9. Interchangeable optics: High efficiency stems, sloped ceiling adapters as well as Basic, temperature for minimum 50,000 hr metalized coating providing up to 98% Advent and Radius track systems. Ceiling and lifetime at 70% lumen maintenance. total reflectivity for optimal light quality, horizontal or vertical wall mounted (adapters 3. Track attachment fitting: Integral color in beam control and punch. Reflector has lens available for Prospec, Halo, Juno and ConTech). gray, black or white. Molded polycarbonate. attached which protects reflector finish Rotates into track and locks into place with and LEDs from contamination. Tool-less Electrical the use of push tabs. Located at center of installation. Reflector sold separately to mass to allow for fixture to hang vertically allow field replaceability. Electronic power supply straight on track and with extensions wands 10.Finishes: Painted with a baked enamel. Input voltage: 120 V, 60 Hz and other track accessories. Contains some powder coated finishes. Input power: 15 W 4. Push tab: Molded polycarbonate. Efficacy: 78 lm/W (nominal) @ 3000 K High power factor: >0.9 Locks and detaches unit. Dimming 5. Track adapter housing: Die-cast aluminum. CRI: 80-85 (typical) 6. Movable brass contact: Brass extends for Trailing edge (ELV) dimming compatible connection to 2nd circuit (Advent track only). ZP425QE Philips Controls (100 - 30%) Labels 7. Pivot mounts: Allows for 350° horizontal. SELV-300P Lutron Skylark (100 - 10%) Vertical rotation of +⁄- 90° from vertical IPE04-ILX Leviton Decora (100 - 23%) cULus Listed. aim to the floor. 5 year warranty. ENERGY STAR® certified LLAV11 05/16 page 1 of 3 philips.com/luminaires (without accessories). Uplighting Large outdoor, integral driver Solid State (LED) Style 172
S Mount 1:10 Scale L Mounting Plate (S Mount) A B G M 3-1/4" C (83mm) 4-1/2" D (114mm) 7" (178mm) E N O F P Cantilever 1:10 Scale G (For use with X Mount) 5-5/8" 9" Length (see table below) (143mm) (229mm)
Side-Mount Slipfitter 1:10 Scale Q (For use with X Mount) R
S # of LEDs Length J 36" (915mm) 36 12-1/16" (306mm) 72 17-13/16" (452mm) 7-1/2" 108 24-7/8" (632mm) (190mm) H J K 2-3/8" 4-1/8" 9" 4" 2-1/4" O.D. (105mm) (229mm) (102mm) (57mm) Specifications Features A Mitred extruded aluminum E Integral driver L Tamper-resistant P Specular extruded Extruded aluminum housing, die-cast aluminum endplates; door frame F Aluminum yoke captive door screws aluminum housing 1000 hour salt-spray test to ASTM B117-90 B Precured silicone door and G Surface splice box M Micro-prismatic impact Q Outlet box (by others) Silicone gaskets – keep dirt and moisture out lens gasket resistant tempered glass lens H Locking set screw R Welded aluminum Yoke set screw – securely locks aiming SU C Cutoff visor N Die-cast aluminum end plates mounting plate with 3.0 J 1/2" NPT nipple Patented fraqtir™ optics produce asymmetric distribution D Field serviceable light engine O Aluminum reveal plate splice access cover K Accessory extruded with fraqtir™ asymmetric optic (black) S 1-1/2" aluminum arm aluminum slipfitter Optic Assembly: Mounting: Performance Two-piece extruded aluminum heat sink housing and light S mount provided with 1/2" NPT nipple, wet location outlet box fraqtir technology 108 LEDs engine. Exterior heat sink anodized for maximum emissivity. and cover finished to match the luminaire. uses a combination Removable interior extrusion treated to maximize thermal X mount for use with aluminum cantilever or slipfitter accessory of refraction and total 72 LEDs conductivity. Precision formed asymmetric optical light bar (ordered separately). Top or side mount slipfitter for 2-3/8" O.D. internal reflection, of high temperature, water-clear acrylic. Extruded aluminium stanchion, pole (by others). creating a distribution 36 LEDs door frame with captive tamper-resistant fasteners. Clear of light ideal for tempered glass lens with elliptical distribution holographic Electrical: illuminating surfaces 7000 Cd diffuser; maximizes lateral distribution without disturbing Use 90°C wire for supply connections. Integral electronic HPF uniformly. Glare is asymmetric forward throw. constant current driver. For complete driver specifications, see minimized while light website, reference document MA-1303. L90(10k) > 60,000 hrs. @ 25°C per TM-21 Finish: delivered to the target Exterior surfaces – 6 stage pretreatment and electrostatically Standard: is maximized, resulting applied thermoset polyester powder coating for a durable CSA certified to UL1598, UL8750, CSA C22.2 for wet locations. in high efficiency. abrasion, fade and corrosion resistant finish. Choice of 5 year warranty, maximum ambient temperature 45°C (113°F). semigloss colors (see ordering information). Extruded aluminum For photometric and lumen heat sink/housing plus yoke, door frame and decorative end maintenance reports, visit plates are finished in color. All hardware and components – thelightingquotient.com non-corrosive stainless steel or aluminum.
5/16 U.S. Patent 8,465,190; foreign patents pending LED Product Partner with fraqtir LED Project: Wall Mount Location: Cat.No:
Type: LED wall sconce 121 Qty: Notes:
Philips Gardco LED wall sconce 121 offers distinction through its styling, powerful optical design, array of distributions, and impressive selection of control possiblilities. Designed to add an element of style to your application by pairing straight lines with rounded edges, the form of the 121 is timeless, yet contemporary, and will complement a wide assortment of architectural styles and designs, while delivering high light levels and functional distributions. 121 sconces are available in Type 2, 3, and 4 distributions, and provide output of up to 10,103 lumens. Energy saving control options help to increase energy savings and offer California Title 24 compliance. Emergency Battery Backup option available for path-of-egress and is integral to the luminaire.
Ordering guide example: 121-32L-700-NW-G3-3-120-IMRI2-BZ
Options Number LED Color - Prefix of LEDs Drive Current Generation Distribution Emergency Voltage Controls Electrical Finish 121
121 16L 530 530 mA CW-G3 2 Type 2 EBPC UNV 120-277V DD 0-10V Dimming Driver5 Fusing Textured LED wall sconce 16 LEDs Cool White Emergency DCC Dual Circuit Control6,7,8 650 650 mA1 3 Type 3 HVU 347-480V F1 Single BK Black (1 modules) 5700K, 70 CRI Battery Pack 10 DynaDimmer: Automatic Profile Dimming (120, 277, 347VAC) WH White 3,4 7000 70 mA Generation 3 4 Type 4 Cold Weather 120 120V BZ Bronze CS50 Safety 50% Dimming5,6 F2 Double DGY Dark Gray 1000 1000 mA NW-G3 Leave blank 208 208V CM50 Median 50% Dimming5,6 (208, 240, 480VAC) 10 5,6 MGY Medium Gray 2 Neutral White to omit an CE50 Economy 50% Dimming 1200 1200 mA 240 240V Canadian Double Pull 4000K, 70 CRI emergency DA50 All Night 50% Dimming5,6 F3 10 Customer specified 32L 530 530 mA Generation 3 option 277 277V (208, 240, 480VAC) Photoelectric Systems RAL Specify optional 32 LEDs 650 650 mA1 WW-G3 347 347V 9,10,11 color or RAL (2 modules) PCB Photocontrol Button Warm White (ex: OC-LGP or 7000 70 mA 480 480V 3000K, 70 CRI Infrared Motion Response Systems OC-RAL7024) 1000 1000 mA Generation 3 IMRI2 Integral with #2 lens3,5 CC Custom color IMRI3 Integral with #3 lens3,5 (Must supply Wireless Controls color chip for (luminaire mounted) required factory quote) LLC2 Module with #2 lens5,6 LLC3 Module with #3 lens5,6
1. Only available with EBPC 7. DCC available only in 530mA with 32 LED 2. Only available with 16 LEDs 8. Not available with EBPC 3. Available in 120V or 277V only 9. Not available with DCC 4. EBPC available only in 530mA or 650mA 10. Voltage must be specified 5. Not available with 1.2A drive current 11. Not available in 480V 6. Available in 120V thru 277V and UNV only.
121_LED_wall_sconce 06/16 page 1 of 6 PROJECT INFORMATION MILLENIUM™ SQUARE Job Name Fixture Type MS11 SERIES – LOW PROFILE HOUSING Catalog Number PRODUCT FEATURES: Approved by »»Surface mount – ceiling (FL & CL only) or wall mount; 12"W×12"W×4"D (CL, EL, FL) FL 15"W×15"W×4"D (DL) »»Peace of Mind Guarantee® »»Dust and water protected to IP64 standards »»ADA compliant
EL DL CL SPECIFICATIONS BASEPLATE: Marine grade die-cast aluminum. Integral heat sinks. Baseplate flange interlocks and wraps around lens base producing maximum moisture deflection and resistance to prying. Baseplate provided with four-point mounting holes and one wireway hole. Standard matte black, dark bronze or matte white exterior TGIC polyester powder coat – 5-step pre-treatment. See Ordering Information for optional finishes. REFLECTOR: Full reflector/wire cover – 92% reflectivity. LENS: UV-stabilized, high impact resistant, virgin injection molded polycarbonate. High efficiency blondel fluted lens maximizes uniformity. Lens secured with four concealed captive Torx® with center pin fasteners. Exclusive water channeling lens design provides 360° ingress protection. LENS BASE/GRILLE: High impact resistant, injection molded matte black, dark bronze or matte white polycarbonate. Optional Light Gray, Silver, Forest Green or Custom Color (see Ordering Information below) are chemically bonded, impact resistant finishes. GASKETING: Die-cut, closed cell EPDM self adhesive gasket seals baseplate to mounting surface. Closed cell, silicone “O” ring gaskets positioned and friction secured in gasket channels of lens base, baseplate and optional surface adapter. HARDWARE: Four stainless steel Torx® fasteners. ELECTRICAL: Available in 3500K, 4000K, and 5000K color temperatures, 80 CRI. 120-277VAC, 50/60Hz electrical input with high power factor electronic, constant-current driver (>.90 PF). Standard 0-10V dimming with 1-100% range; maximum driver source of 200 μA. PHOTOMETRICS: Photometry tested to the IESNA LM-79-08 standard by an ILAC/ISO17025 accredited laboratory. For additional photometric information, go to www.kenall.com. WARRANTY: One (1) year warranty against defects in materials and workmanship. Five (5) year warranty on LED lamps and driver for defects resulting in a fixture lumen depreciation of 30% or greater. LISTINGS: Luminaire is certified to UL Standards by either Underwriters Laboratory or Intertek Testing Laboratory for Wet Location (listing includes Emergency Battery Pack “EL” option). UL certified IP64 per IEC 60598. ADA Compliant.
In Stock SKU ADA IP64 LED C MS11FL-PP-MW-10L40K-DV
ORDERING INFORMATION (Ex: MS11DL-PP-MW-20L40K-DV)
Model Lens Type Finish Lamp Type Voltage Options Accessories PP
Model Lamp Type Options MS11CL Crossbar 10L35K 10 Watt 3500K LED LEL-SA* LED Emergency Battery Backup with Die-cast Surface MS11DL Diamond Eyelid 10L40K 10 Watt 4000K LED Adapter (SA) - Non ADA (n/a with 347V) MS11EL Eyelid 10L50K 10 Watt 5000K LED BPC-SA* Photo Control – Shielded Button Type with Die-cast Surface MS11FL Full Face 20L35K 20 Watt 3500K LED Adapter (SA) - Non ADA (120V or 277V only) 20L40K 20 Watt 4000K LED FS Single Fuse & Holder Lens Type 20L50K 20 Watt 5000K LED NAT Natatorium Environment Option PP Pearlescent Polycarbonate Voltage Accessories Finish 120 120 Volts SA Die-Cast Surface Adapter (Non ADA) DB Dark Bronze 277 277 Volts 9500 Torx® Screwdriver FG Forest Green 347n 347 Volts LG Light Gray DVn 120-277 Volts MB Matte Black n n/a with BPC MW Matte White * LEL-SA and BPC-SA n/a in conjunction SL Silver CC Custom Color (Consult factory)
www.kenall.com P: 800-4-Kenall F: 262-891-9701 10200 55th Street Kenosha, Wisconsin 53144 When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found at www.kenall.com/patents. Content of speci cation sheets is subject to change; please consult www.kenall.com for current product details. © 2016 Kenall Mfg. Co. All rights reserved. MS11_L-063016 Catalog D-Series Size 1 Number LED Area Luminaire Notes
Type
Hit the Tab key or mouse over the page to see all interactive elements. Introduction The modern styling of the D-Series is striking Specifications yet unobtrusive - making a bold, progressive 1.01 ft2 statement even as it blends seamlessly with its EPA: 2 (0.09 m ) WW environment. Length: 33” The D-Series distills the benefits of the latest in (83.8 cm) LED technology into a high performance, high Width: 13” (33.0 cm) efficacy, long-life luminaire. The outstanding L L photometric performance results in sites with Height: 7-1/2” (19.0 cm) excellent uniformity, greater pole spacing and HH Weight 27 lbs lower power density. It is ideal for replacing up to (max): (12.2 kg) 750W metal halide in pedestrian and area lighting applications with typical energy savings of 65% and expected service life of over 100,000 hours.
Ordering Information EXAMPLE: DSX1 LED 60C 1000 40K T3M MVOLT SPA DDBXD DSX1LED
Series LEDs Drive current Color temperature Distribution Voltage Mounting
DSX1 LED Forward optics 530 530 mA 30K 3000 K T1S Type I short T5S Type V short MVOLT 5 Shipped included 30C 30 LEDs (one engine) 700 700 mA 40K 4000 K T2S Type II short T5M Type V medium 120 5 SPA Square pole mounting 40C 40 LEDs (two engines) 1000 1000 mA 50K 5000 K T2M Type II medium T5W Type V wide 208 5 RPA Round pole mounting 2 60C 60 LEDs (two engines) (1 A) AMBPC Amber T3S Type III short BLC Backlight 240 5 WBA Wall bracket 2,4 Rotated optics 1 phosphor T3M Type III medium control 277 5 SPUMBA Square pole universal mounting adaptor 7 converted 3 60C 60 LEDs (two engines) T4M Type IV medium LCCO Left corner 347 6 RPUMBA Round pole universal mounting adaptor 7 cutoff 2,4 TFTM Forward throw 480 6 Shipped separately medium RCCO Right corner cutoff 2,4 KMA8 DDBXD U Mast arm mounting bracket adaptor T5VS Type V very short (specify finish)8
Control options Other options Finish (required)
Shipped installed PIRH1FC3V Bi-level, motion/ambient sensor, 15-30’ mount- Shipped installed DDBXD Dark bronze 15 PER NEMA twist-lock receptacle only (no controls) 9 ing height, ambient sensor enabled at 1fc HS House-side shield 19 DBLXD Black 14,16 PER5 Five-wire receptacle only (no controls) 9,10 BL30 Bi-level switched dimming, 30% WTB Utility terminal block 20 DNAXD Natural aluminum 14,16 PER7 Seven-wire receptacle only (no controls) 9,10 BL50 Bi-level switched dimming, 50% SF Single fuse (120, 277, DWHXD White 17 21 DMG 0-10V dimming driver (no controls) 11 PNMTDD3 Part night, dim till dawn 347V) DDBTXD Textured dark bronze 17 ® 12 PNMT5D3 Part night, dim 5 hrs DF Double fuse (208, 240, DCR Dimmable and controllable via ROAM (no controls) 21 DBLBXD Textured black 17 480V) 13,14 PNMT6D3 Part night, dim 6 hrs DS Dual switching 22 DNATXD Textured natural 17 L90 Left rotated optics 15 PNMT7D3 Part night, dim 7 hrs aluminum PIR Bi-level, motion/ambient sensor, 8-15’ mounting height, ambient sensor enabled at 5fc 22 18 R90 Right rotated optics 15 FAO Field adjustable output DWHGXD Textured white PIRH Bi-level, motion/ambient sensor, 15-30’ mounting height, ambient sensor enabled at 5fc BS Bird spikes PIR1FC3V Bi-level, motion/ambient sensor, 8-15’ mounting height, ambient sensor enabled at 1fc15
NOTES 13 Requires 40C or 60C. Provides 50/50 luminaire operation via two independent drivers on Controls & Shields 1 Rotated optics available with 60C only. two separate circuits. N/A with PER, DCR, WTB, PIR or PIRH. DLL127F 1.5 JU Photocell - SSL twist-lock (120-277V) 23 2 Not available AMBPC. 14 Requires an additional switched circuit. 23 3 Only available with 530mA or 700mA. 15 PIR and PIR1FC3V specify the SensorSwitch SBGR-10-ODP control; PIRH and PIRH1FC3V DLL347F 1.5 CUL JU Photocell - SSL twist-lock (347V) 4 Not available with HS. specify the SensorSwitch SBGR-6-ODP control; see Outdoor Control Technical Guide for DLL480F 1.5 CUL JU Photocell - SSL twist-lock (480V) 23 5 MVOLT driver operates on any line voltage from 120-277V (50/60 Hz). Specify 120V, details. Dimming driver standard. Not available with PER5 or PER7. Ambient sensor disabled 23 208V, 240V or 277V options only when ordering with fusing (SF, DF options). when ordered with DCR. Separate on/off required. DSHORT SBK U Shorting cap 6 Not available with single board, 530mA product (30C 530 or 60C 530 DS). Not 16 Dimming driver standard. MVOLT only. Not available with 347V, 480V, DCR, DS, PER5, DSX1HS 30C U House-side shield for 30 LED unit19 available with BL30, BL50 or PNMT options. PER7 or PNMT options. Not available with PIR1FC3V or PIRH1FC3V. 19 7 Existing drilled pole only. Available as a separate combination accessory; for retrofit use 17 Dimming driver standard. MVOLT only. Not available with 347V, 480V, DCR, DS, PER5, DSX1HS 40C U House-side shield for 40 LED unit only: PUMBA (finish) U; 1.5 G vibration load rating per ANCI C136.31. PER7, BL30 or BL50. Not available with PIR1FC3V or PIRH1FC3V. Separate on/off required. DSX1HS 60C U House-side shield for 60 LED unit19 8 Must order fixture with SPA option. Must be ordered as a separate accessory; see 18 Dimming driver standard. Not available with PER5, PER7, DMG, DCR, DS, BL30, BL50 or Accessories information. For use with 2-3/8” mast arm (not included). PNMT, PIR, PIRH, PIR1FC3V or PIRH1FC3V. Square and round pole universal PUMBA DDBXD U* 24 9 Photocell ordered and shipped as a separate line item from Acuity Brands Controls. See 19 Not available with BLC, LCCO and RCCO distribution. Also available as a separate Accessories mounting bracket (specify finish) accessories. Not available with DS option. accessory; see Accessories information. Mast arm mounting bracket adaptor 10 If ROAM® node required, it must be ordered and shipped as a separate line item from 20 WTB not available with DS. Ordered and shipped separately. and shipped separately. Ordered KMA8 DDBXD U (specify finish)8 Acuity Brands Controls. Not available with DCR. Node with integral dimming. 21 Single fuse (SF) requires 120V, 277V or 347V. Double fuse (DF) requires 208V, 240V or 480V. 11 DMG option for 347V or 480V requires 1000mA. 22 Available with 60 LEDs (60C option) only. 12 Specifies a ROAM® enabled luminaire with 0-10V dimming capability; PER option 23 Requires luminaire to be specified with PER option. Ordered and shipped as a separate required. Additional hardware and services required for ROAM® deployment; must line item from Acuity Brands Controls. For more control options, visit DTL and ROAM online. be purchased separately. Call 1-800-442-6745 or email: [email protected]. N/A 24 For retrofit use only. with PIR options, DS, PER5, PER7, BL30, BL50 or PNMT options. Node without integral dimming.
One Lithonia Way • Conyers, Georgia 30012 • Phone: 800.279.8041 • www.lithonia.com DSX1-LED Rev. 10/19/16 © 2011-2016 Acuity Brands Lighting, Inc. All rights reserved. Page 1 of 6