TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Preparation Part Number: 08586-02891 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description Torque Wrench 36 lbf-in 1 1 V3 Harness Pliers 2 1 ECU Mounting Bracket 3 1 Piezo Buzzer Special Chemicals Notes 4 1 V3 ECU Cleaner 3MTM Prep Solvent-70 5 2 Remote Control Transmitter Glass Cleaner Windex
Hardware Bag Contents General Applicability Item # Quantity Reqd. Description 2006 -Corolla/Matrix with power door locks only. 1 40 Medium Wire Ties 2 15 Large Wire Ties Recommended Sequence of Application 3 2 Small Foam Tape Strips (1 per) Item # Accessory 4 2 Large Foam Tape Strips (2 per) 1 TVIP V3 5 7 Splicing Connectors 2 Audio 6 1 Butyl Tape 3 EC Mirror 7 1 Bolt 8 1 Status Monitor *Mandatory 9 2 Warning Labels Vehicle Service Parts (may be required for reassembly) 10 1 Owner's Manual Item # Quantity Reqd. Description 11 1 Warranty Card 1 12 1 Key Tag 2 3 Additional Items Required For Installation Item # Quantity Reqd. Description Legend
Conflicts STOP: Damage to the vehicle may occur. Do not Note: Do not install in vehicles with factory keyless entry. proceed until process has been complied with. Recommended Tools OPERATOR SAFETY: Use caution to avoid risk of injury. Personal & Vehicle Notes CAUTION: A process that must be carefully observed Protection in order to reduce the risk of damage to the Safety Glasses accessory/vehicle and to ensure a quality installation. Safety Gloves Optional TOOLS & EQUIPMENT: Used in Figures calls out the Vehicle Protection Blankets, Part Boxes specific tools and equipment recommended for this process.
Special Tools Notes Cable Routing Wire Fish Tape
Installation Tools Notes Screwdriver Phillips Head # 2, (or Tip) Screwdriver Small, Flat Blade Wrench 10 mm Socket 10 mm Extension 3" Nylon Panel Removal Tool e.g. Panel Pry Tool #1 Toyota SST # 00002-06001-01 Electrical Tape Pick Tool Side Cutter Tool
Issue: D 05/05/05 Page 1 of 30 pages DIO Only TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follo w approved guidelines to ensure a quality installation.
These guideli nes can be found in the "Accessory Installation Practices" document.
This document covers such items as:- - Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). - Safety (eye protection, rechecking torque procedure, etc.). - Vehicle Dis assembly/Reassembly (panel removal, part storage, etc.). - Electrical Component Disassembl y/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document.
1. Vehicle Disassembly. 12mm Wrench (a) Remove the negative battery cable. Negative Battery Cable (Fig. 1-1) (1) Protect the fender before starting. (2) For automatic equipped vehicles, place the shifter in low gear and set the parking brake prior to disconnecting the battery. Fig. 1-1 (3) Be careful not to touch the positive terminal.
Nylon Panel Removal Tool (b) Remove the driver side step cover. (Fig. 1-2) (1) Cover the floor and seats before starting. (2) Do not scratch the cover.
Fig. 1-2 Step Cover
Nylon Panel Removal Tool (c) Remove the diver side cowl cover. (Fig. 1-3) (1) Remove the nut securing the cover. (2) Do not scratch the cover.
Cowl Cover Nut
Fig. 1-3
Issue: D 05/05/05 Page 2 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure
FOR COROLLA MODELS ONLY. (Steps d - e) Nylon Panel Removal Tool Meter (d) Remove the meter panel cover. (Fig. 1-4) Panel Cover (1) Remove the one clip screw securing the Protective panel. Sheet (2) Place a protective sheet over the steering column to avoid scratching the meter Clip panel area. Screw
Fig. 1-4
(e) Remove the meter panel. (Fig. 1-5) Nylon Panel Removal Tool Meter Panel Screw (1) Remove the one screw securing the meter panel to the dash. (2) Disconnect the two connectors from behind the meter panel. (3) Do not pull on the wires; pull on the connector. Fig. 1-5 Hooks (x2) (4) Care must be taken when removing the panel from the hooks that hold the panel in place, to prevent damage. (5) Be careful not to get cut by the sharp hooks. FOR MATRIX MODELS ONLY. (Steps f-g) (f) Remove the meter panel cover. (Fig. 1-6) Nylon Panel Removal Tool (1) Place a protective sheet over the steering column to avoid scratching the meter panel area. Meter Panel Cover
Fig. 1-6
Issue: D 05/05/05 Page 3 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure (g) Remove the meter panel. (Fig. 1-7) Screw Phillips Screwdriver Meter Panel (1) Remove the one screw securing the meter panel to the dash. Protective Sheet (2) Disconnect the two connectors from behind the meter panel. (3) Do not pull on the wires; pull on the connector. (4) Care must be taken when removing the Fig. 1-7 panel from the hooks that hold the panel in place, to prevent damage. (5) Be careful not to get cut by the sharp hooks. (h) Remove the small accessory box from the lower dash. (Fig. 1-8) (1) Do not scratch the accessory box and the lower dash.
Accessory Box Fig. 1-8
(i) Remove the cluster panel. (Fig. 1-9) Nylon Panel Removal Tool (1) Do not scratch the panel.
Cluster Panel
Fig. 1-9
Issue: D 05/05/05 Page 4 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure (j) Remove the two screws, located behind the Phillips Screwdriver Screw steering wheel, securing the bottom steering Screw column cover. (Fig. 1-10) (1) Do not scratch the cover. (2) With the ignition switch in the ON position, turn the steering wheel left or right to gain access to the screws. Steering Wheel Fig. 1-10 Steering Wheel
(k) Remove the bottom screw and the lower Phillips Screwdriver steering column cover. (Fig. 1-11) (1) Do not scratch the cover.
Screw
FOR COROLLA MODELS ONLY. Column (Steps l-n) Cover Fig. 1-11 (l) Remove the gearshift cover. (1) For Manual Transmission vehicles, Gearshift Knob Cigarette Lighter Connector remove the gearshift knob, then the gearshift cover. (Fig. 1-12)
Gearshift Cover Fig. 1-12
Nylon Panel Removal Tool (2) For Automatic Transmission vehicles,
Cigarette Lighter remove the gearshift cover only. Connector (Fig. 1-13) (3) Disconnect the cigarette lighter connector located underneath the gearshift cover.
Gearshift Cover Fig. 1-13
Issue: D 05/05/05 Page 5 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure (m) Remove the middle heater control knob. Phillips Screwdriver (Fig. 1-14)
Screw Cluster (1) Remove the one screw from the center Panel knob area after the control knob is removed. (2) Do not scratch the panel. Control Knob
Fig. 1-14
(n) Remove the center cluster panel. (Fig. 1-15) Center Cluster Panel (1) Loosen the three left and three right side Clips (x3) clips when removing the cluster panel.
Clips (x3) (2) Disconnect the four connectors from the panel. (3) Do not scratch the panel. Fig. 1-15 FOR MATRIX MODELS ONLY. (Steps o-p) (o) Remove the center cluster panel. (Fig. 1-16) Nylon Panel Removal Tool Cluster Panel (1) Do not scratch the cluster panel. Audio Unit (2) The heater duct and hazard lamp switch must be removed with the cluster panel. Disconnect all connectors and one cable.
Fig. 1-16 (p) Remove the audio unit. (Fig. 1-17) Phillips Screwdriver, 10mm Extension (1) Remove the four screws securing the Screws (x2) audio unit. (2) Remove the harness clip from the bracket of the audio unit.
Fig. 1-17 Audio Unit Screws (x2)
Issue: D 05/05/05 Page 6 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure (q) Remove the passenger side step cover. Nylon Panel Removal Tool (Fig. 1-18) Glove Box (1) Do not scratch the cover.
Step Cover Fig. 1-18
Nylon Panel Removal Tool (r) Remove the passenger side cowl cover. (Fig. 1-19) (1) Remove the one nut securing the cover. Cowl Cover (2) Do not scratch the cover. Nut (s) Remove the glove box assembly. (Fig. 1-20) Fig. 1-19 (1) Do not scratch the glove box assembly. FOR COROLLA MODELS ONLY. (Steps t-v) Glove Box Assembly (t) Remove the rear seat cushion. (Fig. 1-21) (1) Lift the seat cushion straight upward and disengage the clips located beneath the seat. (2) Push the seat belt receptacle through the seat.
Fig. 1-20
Seat Cushion
Fig. 1-21
Issue: D 05/05/05 Page 7 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure (u) Remove the driver side rear passenger step Nylon Panel Removal Tool cover. (Fig. 1-22) Driver's Seat Back (1) Do not scratch the cover.
Fig. 1-22 Step Cover (v) Remove the driver side center pillar cover. Nylon Panel Removal Tool (Fig. 1-23) (1) Do not scratch the glove box assembly.
Pillar Cover
Fig. 1-23 FOR COROLLA MODELS ONLY. (Steps w-x) Floor Mat (w) Remove the trunk floor mat. (Fig. 1-24)
Fig. 1-24 (x) Loosen the trunk side trim panel. (Fig. 1-25) Trim Panel (1) Remove one trim panel clip.
Clip Fig. 1-25
Issue: D 05/05/05 Page 8 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure
2. Piezo Buzzer Installation.
Side Cutter Tool (a) Using one large strip of foam tape and one large wire tie, secure the Piezo Buzzer to the vehicle's harness near the strut tower on the Large Foam Tape Large Wire Tie passenger side of the vehicle. (Fig. 2-1) (1) Do not cover the opening of the Buzzer with foam tape. Piezo Buzzer
Fig. 2-1
Side Cutter Tool (b) Secure the Piezo Buzzer wires to the vehicle harness with two medium wire ties. Vehicle Harness (Fig. 2-2)
Medium Wire Ties (x2) Fig. 2-2
(c) Temporarily secure the Piezo Buzzer wires to Electrical Tape, Cable Routing Tool the cable routing tool with electrical tape. Piezo Buzzer's RED and BLACK wire s (Fig. 2-3)
Piezo Buzzer (1) Fish tape may be used in place of a cable routing tool. Cable Routing Wire (d) Using the pick tool, push the pick through Electrical Tape the grommet cover to make a hole in the Fig. 2-3 grommet in the engine compartment. Push the entire length of the cable routing wire and
Grommet hole made with the pick Piezo Buzzer wires through the grommet hole made with the pick. (Fig. 2-4) (e) Route the cable routing wire and Piezo Buzzer wires to the passenger compartment. (Fig. 2-4) (f) Remove the electrical tape and cable routing Grommet Cover wire from the Piezo Buzzer wires. Fig. 2-4 (in engine compartment)
Issue: D 05/05/05 Page 9 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure
3. V3 Wire Harness Installation. (From Meter Panel area to Trunk area) Utility Knife, Electrical Tape FOR MATRIX MODELS ONLY. (Step a) (a) Cut the V3 harness' RED/WHITE wire, and 10P (White) (100mm) cover the end with electrical tape. (Fig. 3-1) 12P (Blue) (1) Cut the V3 harness' RED/WHITE wire off the branch at about 100mm. V3 Harness' RED/WHITE Wire (2) Do not cut the other wires. Fig. 3-1 Electrical Tape
(b) Cover the weld joint of the steering support Reinforcement brace and the reinforcement with one large strip of foam tape. (Fig. 3-2)
Large Foam Tape
Brace Fig. 3-2
(c) From the meter panel area, route the V3 harness down through the left side of the reinforcement brace above the driver's side J/B. (Fig. 3-3) 10P V3 Harness (White) 12P (1) Due to presence of sharp edges, it is (Blue) recommended that you wear gloves during harness installation. Fig. 3-3
(d) Route the V3 harness down toward the driver V3 Harness side cowl area as shown. (Fig. 3-4) (1) Due to presence of sharp edges, it is recommended that you wear gloves Red/White Wire 3P during harness installation. 4P
Green Wire
Fig. 3-4 12P 10P
Issue: D 05/05/05 Page 10 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure FOR COROLLA MODELS ONLY. (Steps e-g)
Pliers Large Wire Ties (x2) (e) In the meter panel area, locate the RED wire V3 Harness on the vehicle harness meter panel's 40P Medium Wire Tie connector in the top row, first space from the Splicing left and attach the V3 harness' RED wire Connectors with a splicing connector. (Fig. 3-5) Medium Wire Ties RED/WHITE (x2) (1) Turn the connector so the wires face you 40P and the tab is on top. RED Fig. 3-5 WIRE SIDE VIEW (2) Verify the correct wire and connector opening is chosen. (f) Locate the RED/WHITE wire in the top row fourth space from the left of the 40P connector and attach the V3 harness' RED/ WHITE wire with a splicing connector. (Fig. 3-5) (1) Turn the connector so the wires face you and the tab is on top. (2) Verify the correct wire and connector opening is chosen. (g) Secure the V3 harness' RED and RED/WHITE wires to the vehicle harness with three medium wire ties. Secure the V3 harness to the vehicle harness with two large wire ties. (Fig. 3-5)
Issue: D 05/05/05 Page 11 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure FOR MATRIX MODELS ONLY. (Steps h and j) Pliers Large Wire Ties (x2) (h) In the meter panel area, locate the RED/ V3 Harness WHITE wire of the meter panel's 40P Medium Wire Tie connector in the bottom row, fifteenth space Splicing from the left and attach the V3 harness' RED/ Connectors WHITE wire with a splicing connector. Medium Wire Ties RED (x2) (Fig. 3-6) 40P RED/WHITE (1) Turn the connector so the wires face you Fig. 3-6 WIRE SIDE VIEW and the tab is on top. (2) Verify the correct wire and connector opening is chosen. (i) Locate the RED wire of the 40P connector in the bottom row, sixteenth space from the left and attach the V3 harness' RED wire with a splicing connector. (Fig. 3-6) (1) Turn the connector so the wires face you and the tab is on top. (2) Verify the correct wire and connector opening is chosen. Side Cutter Tool (j) Secure the V3 harness RED and V3 Harness Medium Wire Ties (x2) RED/WHITE wires to the vehicle harness V3 Harness' GREEN Wire with three medium wire ties, and secure the V3 harness to the vehicle harness with two large wire ties. (Fig. 3-6) V3 Harness' 10P and 12P (k) Secure the V3 harness to the vehicle harness V3 Harness' with two medium wire ties. (Fig. 3-7) Fig. 3-7 7P and 13P
13P (l) From the meter panel opening, disconnect the vehicle harness' 13P and 7P connectors 7P from the top of the driver side J/B. (Fig. 3-8) (1) Do not pull on the wires; pull on the connector.
Fig. 3-8
Issue: D 05/05/05 Page 12 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure
Vehicle Harness' (m) Plug in the V3 harness' 13P and 7P 13P Connector connectors between the driver side J/B and the vehicle harness. (Fig. 3-9) Vehicle Harness' 7P Connector (1) Verify the connectors are plugged in V3 Harness' 13P Connector securely.
V3 Harness' 7P Fig. 3-9 Connector
Side Cutter Tool (n) Secure the V3 harness' 13P and 7P connector wires to the vehicle harness with one V3 Medium Wire Tie Harness medium wire tie, and secure the V3 harness 13P to the vehicle harness with one medium wire V3 Harness tie. (Fig. 3-10) 7P Medium 13P Wire Tie Fig. 3-10 7P Driver Side J/B (o) Locate and disconnect the 16P connector Wire Side View Pliers from top of the driver side J/B. Locate the 16P connector's GREEN wire in the bottom row, second space from the left, and attach GREEN the V3 harness' GREEN wire with a splicing Lock Cover connector. (Fig. 3-11)
16P (1) Verify the correct wire and connector Fig. 3-11 opening is chosen. (p) Plug the 16P connector back into the driver side J/B. (Fig. 3-11) (q) Secure the V3 harness to the vehicle harness Side Cutter Tool V3 Harness' GREEN Wire with one medium wire tie. (Fig. 3-12) Medium Wire Tie
Splicing Connector
V3 Harness
Fig. 3-12
Issue: D 05/05/05 Page 13 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure (r) Locate and disconnect the blue 12P and 12P (Blue) white 10P connectors from the connector block in the driver side cowl area. (Fig. 3-13) (1) Do not pull on the wires; pull on the connector. 10P (White)
Fig. 3-13
(s) Plug in the V3 harness blue 12P connectors V3 Harness' V3 Harness 12P Connector between the vehicle harness 12P connector Vehicle Harness' and the driver side cowl area. Then plug in 12P Connector V3 Harness' 10P Connector the V3 harness white 10P connectors
Vehicle Harness' between the vehicle harness 10P connector 10P Connector V3 Harness' and the driver side cowl area. (Fig. 3-14) RED/WHITE Wire (1) Verify the connectors are plugged in V3 Harness' 12P Fig. 3-14 V3 Harness' 10P Connector Connector securely. FOR MATRIX MODELS ONLY. (Step t) (t) Secure the V3 harness to the vehicle harness Side Cutter Tool V3 Harness with three medium wire ties. (Fig. 3-15) Medium Wire Ties (x2) 12P
Medium 10P Wire Tie
V3 Harness' Fig. 3-15 RED/WHITE Wire
Issue: D 05/05/05 Page 14 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure FOR COROLLA MODELS ONLY. Side Cutter Tool V3 Harness (Steps u-x) (u) Locate the RED/WHITE wire from the V3 Medium 12P Wire Ties (x2) harness. Secure the RED/WHITE wire from the V3 harness to the vehicle's harness in the Medium Wire Tie Medium driver side cowl area with four medium wire V3 Harness' Wire Tie ties. (Fig. 3-16) RED/WHITE Wire
Fig. 3-16 10P
Side Cutter Tool Vehicle Clip (v) Route the V3 harness RED/WHITE wire V3 Harness' through the driver side step area and secure it RED/WHITE Wire to the vehicle harness with two vehicle clips and four medium wire ties. (Fig. 3-17) Vehicle Clip
Medium Wire Ties (x4)
Fig. 3-17
(w) Continue routing the V3 harness Side Cutter Tool V3 Harness' RED/WHITE Wire RED/WHITE wire through the driver side pillar area and secure it to the vehicle harness with one medium wire tie. (Fig. 3-18)
Medium Wire Tie Fig. 3-18
Side Cutter Tool (x) Continue routing the V3 harness' Vehicle Clip RED/WHITE wire back toward the driver's V3 Harness' RED/ WHITE Wire side rear passenger step area. Secure the V3 harness wire to the vehicle harness with one vehicle clip and three medium wire ties. (Fig. 3-19) Medium Wire Ties (x3) Fig. 3-19
Issue: D 05/05/05 Page 15 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure
FOR COROLLA MODELS ONLY. (Steps y-bb) V3 Harness' RED/WHITE (y) Route the V3 harness' RED/WHITE wire up Wire toward the driver's side rear passenger seat. Secure the V3 harness wire with two large pieces of foam tape as shown. (Fig. 3-20)
Fig. 3-20 Large Foam Tapes (x2) (z) Route the V3 harness' RED/WHITE wire Side Cutter Tool Vehicle Harness under the driver side rear passenger seat back
V3 Harness into the trunk, then route the V3 harness' Medium Wire Ties RED/WHITE wire from the backside of the (x4) Vehicle Harness' driver's side rear passenger seat back along RED/WHITE Wire the vehicle's harness, up toward the fabric trim panel area. (Fig. 3-21) Splicing Connector V3 Harness' RED/ WHITE Fig. 3-21 Wire (aa) Secure the V3 harness to the vehicle harness with four medium wire ties as shown. (Fig. 3-21) (bb) Locate the RED/WHITE wire from the vehicle harness and attach the V3 harness' RED/WHITE wire with a splicing connector. (Fig. 3-21) (1) Verify the correct wire is chosen for splicing. (2) Verify the splicing connector is applied properly.
Issue: D 05/05/05 Page 16 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure
4. V3 Wire Harness Installation. Side Cutter Tool Large Wire Tie (From Meter Panel area to passenger side area)
V3 Harness (a) From the right side of the meter panel opening, route the V3 harness branch down towards the ignition key cylinder area and center console area. Secure it to the vehicle V3 Harness' Relay harness with one large wire tie, then secure
Fig. 4-1 Large Wire Tie the V3 harness relay to the vehicle harness with one large wire tie. (Fig. 4-1) (b) Locate and disconnect the vehicle harness' black 2P and white 6P connector from the steering column area. (Fig. 4-2)
6P (White) (1) Do not pull on the wires; pull on the connector.
(c) Plug in the V3 harness' black 2P connector Fig. 4-2 2P (Black) between the vehicle harness' black 2P connector and the steering column area, then plug in the V3 harness' white 6P connector
V3 Harness between the vehicle harness' white 6P V3 Harness' 2P connector and the steering column area. Connector V3 Harness' Vehicle Harness' 6P Connector (Fig. 4-3) 2P Connector (1) Verify the connectors are plugged in Vehicle Harness' 6P Connector securely. Fig. 4-3 V3 Harness' 6P Connector (d) Locate in the lower steering column area the 13P connector's RED wire in the bottom row, Pliers second space from the left, and attach the V3 13P harness RED wire with a splicing connector. WIRE SIDE (Fig. 4-4) VIEW (1) Turn the connector so the wires face you and the tab is on top.
Splicing V3 Harness' (2) Verify the correct wire is chosen for RED Connector RED Wire Fig. 4-4 splicing. (3) Verify the splicing connector is applied properly.
Issue: D 05/05/05 Page 17 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure (e) Disconnect the black 12P connector from the steering column area. (Fig. 4-5) (1) Do not pull on the wires; pull on the connector.
12P (Black)
Fig. 4-5 Key Cylinder (f) Connect the V3 harness' white 12P connector to the vehicle harness' black 12P connector,
12P (Black) and plug in the V3 harness' black 12P 12P (Black) connector to the steering column connector. 12P (White) (Fig. 4-6) (1) Verify the connectors are plugged in securely.
Fig. 4-6 V3 Harness (g) Secure the V3 harness' 12P connector and
Side Cutter Tool RED wire to the vehicle harness with two 12P 13P medium wire ties. (Fig. 4-7)
Splicing Connector V3 Harness' Medium Wire RED Wire Ties (x2)
V3 Harness 12P Fig. 4-7 12P (h) Secure the V3 harness' 2P and 6P connector wires to the vehicle harness with two Side Cutter Tool V3 Harness medium wire ties. (Fig. 4-8)
2P (i) Secure the V3 harness excess to the vehicle harness with one medium wire tie. (Fig. 4-8)
Medium Wire Ties V3 Harness (x2) Medium Wire Tie Fig. 4-8 6P
Issue: D 05/05/05 Page 18 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure FOR COROLLA MODELS ONLY. (Step j) Side Cutter Tool (j) Route the V3 harness toward the center V3 Harness console area as shown, then secure it to the vehicle harness with three large wire ties behind the heater control unit. (Fig. 4-9) (1) Route the V3 harness away from any moving parts such as levers, etc. Fig. 4-9 Large Wire Ties (x3) FOR MATRIX MODELS ONLY (Step k) Side Cutter Tool (k) Route the V3 harness toward the center console area as shown, then secure it to the V3 Harness vehicle harness with three large wire ties in the back of the audio unit opening. (Fig. 4-10) (1) Route the V3 harness away from any moving parts such as levers, etc. Fig. 4-10 Large Wire Ties (x3)
Side Cutter Tool (l) Route the V3 harness across the glove box V3 Harness area, then secure it to the vehicle harness with three large wire ties. (Fig. 4-11)
Large Wire Ties (x3) Fig. 4-11 (m) Attach the V3 harness' RED wire to the Piezo
Side Cutter Tool V3 Harness Piezo Buzzer's RED Buzzer's RED wire with a splicing connector. and BLACK wire s Then attach the V3 harness' BLACK wire to Splicing Connectors the Piezo Buzzer's BLACK wire with a (x2) splicing connector. (Fig. 4-12) (1) Verify the correct wire is chosen for splicing. V3 Harness' RED and BLACK Wire s (2) Verify the splicing connector is applied Fig. 4-12 GREEN Antenna Wire ECU Connectors properly. (3) Cut the excess wire from the Piezo Buzzer wires.
Issue: D 05/05/05 Page 19 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure 5. V3 ECU Preparation and Installation. Small Flat Blade Screwdriver (a) Turn the adjustment screw on the V3 ECU to the "5" position. (Fig. 5-1)
V3 ECU
Fig. 5-1 (b) Insert the ECU mounting bracket into the Bracket indicated bracket slot on the V3 ECU. (Fig. 5-2) (1) Insert the mounting bracket into the correct slot; you have only one chance to V3 ECU install it properly. (2) Ensure the bracket is firmly attached to Fig. 5-2 the ECU. (c) Apply one piece of butyl tape as shown.
Butyl Tape (Fig. 5-3) (1) Do not remove the protective sheet from the butyl tape.
Fig. 5-3 (d) Install the ECU mounting bracket with the 10mm Wrench, 10mm Socket Extension Brace bolt supplied in the kit to the vehicle brace in Bolt the upper right portion of the glove box area. (Fig. 5-4) V3 Harness (e) Connect the V3 harness' ECU connectors to the V3 ECU. (Fig. 5-4) V3 ECU (1) Verify the connectors are plugged in V3 Harness' GRAY Fig. 5-4 Antenna Wire securely.
Issue: D 05/05/05 Page 20 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure 6. V3 Harness Installation. (Passenger side cowl area) (a) Locate and disconnect the white 10P connector from the passenger side cowl area. (Fig. 6-1) (1) Do not pull on the wires; pull on the 10P connector.
Fig. 6-1
(b) Plug in the V3 harness' white 10P connector V3 Harness Vehicle Harness' between the vehicle harness' 10P connector 10P Connector and the passenger side cowl area. (Fig. 6-2) (1) Verify the connectors are plugged in securely. V3 Harness' V3 Harness' 10P Connector 10P Connector
Fig. 6-2
Side Cutter Tool (c) Secure the V3 harness' 10P connector and the 10P V3 harness to the vehicle harness with one V3 Harness medium wire tie. (Fig. 6-3)
Medium Wire Tie 10P
Fig. 6-3
7. Antenna Wire Installation. Side Cutter Tool Medium Wire Tie (a) Secure the V3 harness' RED and BLACK Piezo Buzzer's RED wires, the Piezo Buzzer's RED and BLACK V3 Harness' RED and BLACK Wires wires and the V3 harness' GREEN antenna and BLACK Wire s Medium Wire Tie wire to the vehicle harness with three Splicing Connectors (x2) medium wire ties. (Fig. 7-1)
V3 Harness' GREEN Fig. 7-1 Medium Wire tie Antenna Wire
Issue: D 05/05/05 Page 21 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure 8. Status Monitor Installation. (a) Remove the knock out cover or the Status Monitor immobilizer indicator (if equipped) in the cluster panel, first space from the right. Then insert the status monitor into the knockout space. (Fig. 8-1) (1) Do not scratch the panel.
Cluster Panel Fig. 8-1
(b) Connect the V3 harness' 3P connector to the vehicle harness' 3P connector. (Fig. 8-2) V3 Harness V3 Harness' Black (1) Verify the connectors are plugged in 4P Connector securely.
Vehicle Harness' V3 Harness' White Fig. 8-2 White 3P Connector 3P Connector (c) Connect the V3 harness' 4P connector to the Small Foam Tape status monitor's 4P connector. (Fig. 8-3) 3P (1) Verify the connectors are plugged in securely. (d) Wrap the 3P connector and the V3 harness' 4P (Black) 4P connector wires with one small strip of Status Monitor foam tape, then insert into the cluster panel Fig. 8-3 Cluster Panel opening. (Fig. 8-3)
9. Warning Label Installation. (a) Using 3MTM Prep Solvent70 or Windex, Warning Label 10mm Line up with bottom clean the inside surface of the front door's of window etching windows. (Fig. 9-1) (b) Place the warning label on the inside surface of the front door's window as shown. (Fig. 9-1)
Fig. 9-1
Issue: D 05/05/05 Page 22 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Procedure (1) Use a piece of clear adhesive tape to lift the labels off their protective backing sheet. (2) Do not touch the adhesive surface of the warning labels. (3) Line up the labels properly and place them on the glass once; do not use a label that was pulled off the glass. (c) Attach the key tag to the remote control key's Remote Control ring. (Fig. 9-2) Key Ring 10. Completing the Installation (a) Complete the reassembly of the vehicle. (b) Reconnect any disconnected connectors.
Key Tag (c) Verify the panels fit together properly with Fig. 9-2 no uneven gaps between them. (d) Clean up and remove any trash.
Torque Wrench, 10mm Socket (e) Reconnect the vehicle's negative battery
Battery 90º cable. (Fig. 10-1) Negative Battery Cable (1) Position the negative terminal at an angle of 90° to the battery as shown. (2) Tighten the nut with 4.1 N-m (36 lbf-in) of torque. Battery Fig. 10-1 (3) Be careful not to touch the positive battery terminal. (4) Place the owner's manual, warranty card, and remote transmitters, left in their protective bags, in the glove box.
Issue: D 05/05/05 Page 23 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Accessory Function Checks
Fit appropriate fuse before beginning.
Press and release the remote control's lock 1. The tail and marker lights flash once. button to start the system's arming process. The buzzer chirps once. All doors lock. The Status Monitor's LED lights up.
Wait 30 seconds. 2. After 30 seconds, the LED starts flashing; the system is now armed.
Press and release the remote control's 3. The tail and marker lights flash twice. unlock button to disarm the system. The buzzer chirps twice. The interior lights turn on for thirty seconds. The driver's door unlocks. The Status Monitor's LED stops flashing.
Press and release the remote control's 4. The tail and marker lights flash twice. unlock button again within 3 seconds of The buzzer chirps twice. disarming the system. All remaining doors unlock.
Open and close the driver's door.
Arm and disarm the system with the remote 5. The doors automatically relock. again, then wait 30 seconds. The system automatically starts the arming process.
Press and release the remote control's 6. Refer to step number 3. unlock button again to stop the arming process.
Open the driver's door, then press and 7. The buzzer sounds continuously for 5 release the remote control's lock button. seconds.
Close the driver's door. 8. The buzzer stops sounding.
Issue: D 05/05/05 Page 24 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Press and release the remote control's panic 9. The horn sounds repeatedly. button to trigger the panic alarm. The interior lights turn on. The headlights flash repeatedly. The tail and marker lights flash repeatedly. The LED lights up.
Press and release the remote control's panic 10. The horn stops sounding. button again to stop the panic alarm. All the lights stop flashing and/ or turn off.
Sit in the driver's seat and make sure all doors are closed.
Insert the key into the ignition switch and 11. All doors lock. turn it to "ON."
Roll down all the windows.
Turn the key back to "LOCK." 12. All doors unlock.
Remove the key and exit the vehicle.
Insert the key into the driver's door key 13. All doors lock. cylinder and turn it toward the front of the The LED lights up. vehicle to start the arming process.
Wait 30 seconds. 14. After 30 seconds, the LED starts flashing; the system is now armed.
Reach inside and manually unlock the 15. The driver's door automatically relocks. driver's door. The horn sounds repeatedly. The interior lights turn on. The headlights flash repeatedly. The tail and marker lights flash repeatedly. The LED lights up.
Issue: D 05/05/05 Page 25 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Manually unlock the driver's door again and 16. The driver's door lock attempts to lock hold it unlocked, open the door, then sit in repeatedly. the driver's seat. The horn continues to sound repeatedly. The interior lights remain on. The headlights, tail lights and marker lights continue flashing. The LED remains on.
Insert the key into the ignition switch and 17. The horn stops sounding. turn it to "START" to stop the alarm. All the lights stop flashing and/ or turn off.
The Status Monitor LED turns off. The starter cranks and the engine starts.
Turn the key back to "LOCK," remove it, and then exit the vehicle.
With the door open, press the lock switch 18. All doors lock. on the door to lock the doors, then close the The Status Monitor's LED lights up. door to start the system's arming process.
Wait 30 seconds. 19. After 30 seconds, the LED starts flashing; the system is now armed.
Reach inside and manually unlock the front 20. The front passenger's door automatically passenger's door to trigger an alarm. relocks. The horn sounds repeatedly. The interior lights turn on. The headlights flash repeatedly. The tail and marker lights flash repeatedly. The LED lights up.
Press and release the remote control's 21. The horn stops sounding. unlock button to stop the alarm. All the lights stop flashing and/ or turn off. The Status Monitor's LED turns off.
Issue: D 05/05/05 Page 26 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Press and release the remote control's lock 22. Refer to step number 1 and number 2. button to start the system's arming process, then wait 30 seconds until the system is armed.
Unlock and open one of the rear passenger 23. Refer to step number 9. doors to trigger an alarm.
Repeat the above steps with the other rear 24. Refer to step number 22 and 23. passenger and back door (if equipped).
Roll up all windows, remove the key and exit the vehicle.
Press and release the remote control's lock 25. Refer to step number 1. button to start the system's arming process.
Wait 30 seconds. 26. After 30 seconds, LED starts flashing; the
system is now armed.
Perform the following check in a
temperature-controlled environment (50° 90° F.)
With the tip of the key, tap the center of the 27. The horn sounds repeatedly. driver's door window to trigger the "warn The headlights flash repeatedly. away" alarm. The tail and marker lights flash repeatedly.
The LED lights up. NOTE: Adjust as necessary by increasing the GBS setting to the next level if the alarm does not trigger during the functional verifications.
NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration.
Issue: D 05/05/05 Page 27 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Insert the key into the driver's door key 28. The horn stops sounding. cylinder and turn it toward the back of the All the lights stop flashing and/or turn off. vehicle to stop the alarm. The status monitor's LED turns off.
Vehicle Function Checks
Head Lights Functioning Head Lights
High Beams Functioning High Beams
Turn Signal Lights Functioning Turn Signal Lights
Tail Lights Functioning Tail Lights
Stop Lights Functioning Stop Lights
Backup Lights Functioning Backup Lights
Hazard Lights Functioning Hazard Lights
Marker Lights Functioning Marker Lights
Dome/Courtesy/Map Lights Functioning Dome/Courtesy/Map Lights
Panel/Switch Illumination Functioning Controls/Illumination
Accessory Controls/Illumination (if Functioning Accessory equipped)
Key Sensor Buzzer Functioning Key Sensor
Fog Lights (if equipped) Functioning Fog Lights
Daytime Running Lights (if equipped) Functioning DR Lights
Trunk/Tailgate/Bed Lights (if equipped) Functioning Lights
Glove Box Light (if equipped) Functioning Glove Box Light
Cruise Control Light (if equipped) Functioning Cruise Control Light
Issue: D 05/05/05 Page 28 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Seat Belt Warning Light Functioning Seatbelt Warning Light. If the warning light remains "ON," it may indicate a system malfunction.
Air Bag Warning Light Functioning Air Bag Warning Light. If the warning light remains "ON," it may indicate a system malfunction.
ABS Light (if equipped) Functioning ABS Light. If the warning light remains "ON," it may indicate a system malfunction.
Lamp Failure Sensor (if equipped) Functioning Lamp Failure Light. If the warning light remains "ON," it may indicate a system malfunction.
Track/Skid Control Light (if equipped) Functional Track/VSC Light. If the warning light remains "ON," it may indicate a system malfunction.
HVAC All HVAC Controls Function
Power Locks (if equipped) Functioning Power Locks
Power Windows (if equipped) Functioning Power Windows
Power Seats (if equipped) Functioning Power Seats
Power Sunroof (if equipped) Functioning Sunroof
Horn Functioning Horn
Gauges Functioning Gauges
Front Wiper/Washer Functioning Front Wiper/Washer
Rear Wiper/Washer (if equipped) Functioning Rear Wiper/Washer
Clock (if equipped) Functioning Clock
Issue: D 05/05/05 Page 29 of 30 pages DIO Only
TOYOTA COROLLA/ MATRIX 2006 - TVIP V3 (RS3200) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Accessory Power Socket (if equipped) Functioning Power Socket
Starter Functioning Starter
Audio/Video (if equipped) Functioning Audio/Video
Power Sliding Door (if equipped) Functioning Power Sliding Door
Convenience Memory Settings (if Functioning Memory Settings equipped)
Heated Seats (if equipped) Functioning Heated Seats
Massage Seats (if equipped) Functioning Massage Seats
Rear Window Defogger (if equipped) Functioning Rear Window Defogger
Power Side Mirrors (if equipped) Functioning Power Side Mirrors
Side Mirror Defogger (if equipped) Functioning Side Mirror Defogger
Front Windshield Defogger (if equipped) Functioning Front Windshield Defogger
Navigation System (if equipped) Functioning Navigation System
Tire pressure warning light Functioning tire pressure warning light
Issue: D 05/05/05 Page 30 of 30 pages DIO Only