14176: Police Equipment Upfitter Interface Module (2008 Dodge

ENGINEERING COMPANY INC. 51 Winthrop Road Installation Guide: Chester, Connecticut 06412-0684 Police Equipment Upfitter Phone: (860) 526-9504 Interface Module Internet: www.whelen.com (2008 Dodge Charger/Magnum) Sales e-mail: [email protected] Customer Service e-mail: [email protected]

WARNING: This product can expose you to chemicals including Lead which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

This module provides conditioned signals to and from the further information, refer to the Police Package Owner’s Police Equipment Interface Module (PEIM) found on all Manual supplied with the vehicle. Dodge Charger/Magnum police vehicles. The 24-position PEIM connector is located under the Instrument Panel WARNING! Do not alter the vehicle harness circuits Center Console. To access this connector, it is necessary in any manner (including splicing or cutting). to remove the plastic cover located just ahead of the police equipment mounting bracket on the center console. For

REAR VIEW REAR VIEW REAR VIEW (to Police Equipment (to Dodge Charger (to aftermarket Interface Connector) Interface Module) police equipment)

1 13 214 1 11 3 15 212 4231 4 16 3 13 5 17 4 14 109685 7 618 5 15 15 14 181716 13 12 11 7 19 616 820 717 22 21 2423 20 19 9 21 818 10 22 9 19 11 23 10 20 12 24

PIN 1 - BRN (FRONT WIG-WAGS) PIN1-BRN (FRONT WIG-WAGS) PIN1-Input / BRN (FRONT WIG-WAGS)* PIN 2 - RED (REAR WIG-WAGS) PIN 2 - RED (REAR WIG-WAGS) PIN 2 - Input / RED (REAR WIG-WAGS)* PIN 3 - ORG (POLICE RADIO MUTE) PIN 3 - ORG (POLICE RADIO MUTE) PIN 3 - Input / ORG (POLICE RADIO MUTE)* PIN 4 - WHT/BLK (BRAKE) PIN 4 - YEL (SIDE AIR BAG STATUS) PIN 4 - Output / YEL (SIDE AIR BAG STATUS)** PIN 5 - BLK/WHT (HORN SWITCH ACTIVATED) PIN 5 - GRN (FRONT AIR BAG STATUS) PIN 5 - Output / GRN (FRONT AIR BAG STATUS)** PIN 6 - WHT/GRY (PARK) PIN 6 - BLU (FUEL LEVEL) PIN 6 - Output / BLU (FUEL LEVEL)** PIN 7 - WHT (ALARM ACTIVATED) PIN 7 - VIO (DRIVER’S SEAT BELT STATUS) PIN 7 - Output / VIO (DRIVER’S SEAT BELT STATUS)** PIN 8 - WHT/YEL (HEADLIGHT) PIN8-GRY(MALFUNCTION INDICATOR) PIN 8 - Output / GRY (MALFUNCTION INDICATOR)** PIN 9 - YEL (SIDE AIR BAG STATUS) PIN 9 - WHT (ALARM ACTIVATED) PIN 9 - Output / WHT (ALARM ACTIVATED)** PIN 10 - GRN (FRONT AIR BAG STATUS) PIN 10 - BLK/WHT (HORN SWITCH ACTIVATED) PIN 10 - Output / BLK/WHT (HORN SWITCH ACTIVATED)** PIN 11 - N/C PIN 11 - N/C PIN 11 - Input / WHT/BRN (ALARM OFF)* PIN 12 - N/C PIN 12 - N/C PIN 12 - Input / WHT/RED (HORN MUTE)* PIN 13 - WHT/BLU (DASH LIGHT DIMMER) PIN 13 - WHT/BRN (ALARM OFF) PIN 13 - Input /WHT/ORG ( N ot Used) PIN 14 - BLU/BLK (ENGINE RUNNING) PIN 14 - WHT/RED (HORN MUTE) PIN 14 - Output / WHT/YEL (HEADLIGHT)** PIN 15 - WHT/GRN (DRIVER DOOR AJAR) PIN 15 - N/C PIN 15 - Output / WHT/GRN (DRIVER’S DOOR AJAR)** PIN 16 - N/C PIN 16 - WHT/YEL (HEADLIGHT) PIN 16 - Output / WHT/BLU (DASHLIGHT DIMMER)** PIN 17 - N/C PIN 17 - WHT/GRN (DRIVER’S DOOR AJAR) PIN 17 - Output / WHT/VIO (VEHICLE SPEED)** PIN 18 - N/C PIN 18 - WHT/BLU (DASHLIGHT DIMMER) PIN 18 - Output / WHT/GRY (PARK)** PIN 19 - WHT/VIO (VEHICLE SPEED) PIN 19 - WHT/VIO (VEHICLE SPEED) PIN 19 - Output / WHT/BLK (BRAKE)** PIN 20 - WHT/RED (HORN MUTE) PIN 20 - WHT/GRY (PARK) PIN 20 - Output / BLK (ENGINE RUNNING)** PIN 21 - WHT/BRN (ALARM OFF) PIN 21 - WHT/BLK (BRAKE) PIN 22 - BLU (FUEL LEVEL) PIN 22 - BLU/BLK (ENGINE RUNNING) *Inputs require a 0.25ma signal MIN (12VDC) PIN 23 - VIO (DRIVER'S SEAT BELT STATUS) PIN 23 - N/C **Outputs are rated for 250ma@12VDC MAX PIN 24 - GRY (MALFUNCTION INDICATOR) PIN 24 - N/C Miscellaneous (Sample Connections) SP/ST Switch 1A Fuse BRN (front wig-wags) - Input +12VDC

STAND RAD PA MAN HF WAIL YELP T3 Butt Splice BY

AIR 9 123 MANUAL HORN VOL. VOL. (LOW (MOM.) WHT/YEL (headlight) - Output YEL (backlight) (MOM.) UP DOWN POWER)

SW8 SW4 SW5 SW6 SW7 (T/A)

12 In the above configuration, the front wig-wags are activated with the SP/ST switch shown. Not Used

5A Fuse Also, when the vehicle headlights are turned on, (Customer Supplied) Pin 1 - RED (To +12VDC) the headlight output wire (WHT/YEL) will provide Pin 2 - BLACK (To Ground) +12VDC to the backlight wire of the sample control head. WARNING! All customer supplied wires that connect to the positive terminal of the battery must be sized to supply at least 125% of the maximum operating Remember: current and FUSED at the battery to carry that load. DO InputsREQUIRE +12VDC NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT! Automotive: OutputsPROVIDE +12VDC