OWNER’S MANUAL

CUSTOMER ASSISTANCE In our constant endeavor to provide assistance and complete You can also approach nearest dealer. A sepa- service backup, TATA MOTORS has established an all India cus- rate Dealer network address booklet is provided with the tomer assistance centre. Owner’s manual. In case you have a query regarding any aspect of your vehicle, TATA MOTORS 24X7 Roadside Assistance Program offers tech- our Customer Assistance Centre will be glad to assist you on nical help in the event of a breakdown. Call to the toll-free our Toll Free no. 1800 209 7979 Roadside Assistance. For additional information, refer to "24X7 Roadside Assis-

tance" section in the Owner’s manual.

ii

Dear Customer,

Welcome to the TATA MOTORS family.

We congratulate you on the purchase of your new vehicle and are privileged to have you as our valued customer.

We urge you to read this Owner's Manual carefully and familiarize yourself with the equipment descriptions and operating instruc- tions before driving.

Always carry out prescribed service / maintenance work as well as any required repairs at an authorized TATA MOTORS Dealers or Authorized Service Centre’s (TASCs). Use only genuine parts for continued reliability, safety and performance of your vehicle.

You are welcome to contact our dealer or Customer Assistance toll free no. (1800 209 7979) in case of any query or support required.

We wish you a safe and pleasant driving experience.

Bombay House, 24, Homi Modi Street, Hutatma Chowk, Fort, Mumbai – 400001

iii IMPORTANT INFORMATION  Before driving, read this Owner’s manual carefully and familiarize yourself with your vehicle. For your own safety and a longer vehicle life, follow the instructions, ‘Warnings’ and ‘Notes’ in this manual. Ignoring them could result in damage to the vehicle or personal injury to you or others.

 The Owner’s manual and other booklets are important documents and should always be kept in the vehicle. If you sell the vehicle, always pass on the documents to the new owner.

 This Owner's Manual describes all variants of the model and all standard/optional equipment of your vehicle available at the time of printing. Please note that your vehicle may not be equipped with all features described.

 TATA MOTORS Limited reserves the right to introduce changes in the design, equipment and technical features without any obligation to install them on the vehicles previously sold. The equipment in your vehicle may therefore differ from that shown in the descriptions and illustrations.

 Do not carry out any modification including fitment of non-genuine accessories on your vehicle. Safety, handling, performance and durability, may otherwise be adversely affected and may violate government regulations. TATA MOTORS Limited accepts no liability for damage resulting from the modifications or use of non-genuine accessories.

 All rights reserved. The information in this manual shall not be copied, translated or otherwise reproduced, in whole or in part, without written permission from TATA MOTORS.

© Copyright 2019 TATA MOTORS

iv CONTENTS

1 Safety 2 Opening & Closing 3 Dashboard & Features

Important Information 01 Flip Key 19 Cockpit 27

Safe Driving 01 Doors 21 Instrument Cluster - Analog 29

Seat Belts 04 Windows 22 Driver Information Display 34

Child Restraint System (CRS) 07 Bonnet 24 Driver Information Settings 39

Supplementary Restraint Trunk lid 25 Instrument Cluster - Digital 43 System (SRS) (Airbags) 11 Fuel lid 26 Warning Lamps 56 ABS 18

Audio Reminders 63 EBD 18

Combi Switches 64

Fascia Switches 65

Steering Wheel Switches 67

Mic 67

v CONTENTS

3 Dashboard & Features 4 Stowage Areas 5 Climate Control

Infotainment System 68 Storage Compartments 73 Air Vents & Distribution 77

USB/AUX 68 Glove Box 74 HVAC Controls 78

Power Socket 68 Driver side pocket 74 Functions & Settings 80

Antenna 69 Center Console 75 Fully Automatic temperature Control 82 Roof Lamp 69 Foldable arm rest 75

HVAC sensors 88 Roof Grab Handles 70 Trunk lid Compartment 75

Boot Lamp 70 Card Holder 76

Tag Holder 71 Hooks 76

vi CONTENTS

6 Starting & Driving Emergency & Break- 8 Maintenance 7 down Assistance Pre-Driving Checks 89 Maintenance & Service 147 Emergency Equipment 117 Driving Tips 90 Engine Compartment 148 Hazard Warning Switch 118 Seat Adjustments 93 Engine Oil Level 151 In Case of Flat Tyre 119 Rear View Mirrors 94 Battery 154 Spare Wheel 119 Steering Wheel Adjustments 96 Spark Plug 155 Jump Lead Starting 124 Starting the Engine 97 Tyres 155 Towing 125 Gear Shifting & Driving 98 Key Battery Replacement 158 Fuses 128 AMT Gearbox 100 On Board Diagnostic (OBD) 159 Bulb Replacement 135 Driving Mode 102 Service Instructions 160 24x7 Road Side Assistance 140 Parking brakes 107 Service Schedule 161

Vehicle Tracking System (VTS) 143

Reverse Park Assist 108 124 Parking for Long Durations 167

vii CONTENTS

9 Technical Information Car Care and Value Warranty – Terms and 10 11 Added Services Conditions Fuel Specification 169 Car Care 179 Warranty 189 Lubricant Specification 171

Washing 179

Technical Specification 173 12 Environment Safety Waxing 180

Vehicle Dimensions 177

Polishing 180 Environmental Safety 191 Aggregate Identification Nos 178 Interior Fabric Cleaning 180

Paint Care 181

Extended Warranty 182

Value Added Services 184

Vehicle Exterior Enrichment 186

Vehicle Interior Enrichment 187

viii SAFETY Important Information Safe Driving Safety Tips In this Owner's Manual, you will find the Safety consciousness not only ensures  Always take into account the road text under the heading “WARNING” and your safety and the safety of other road conditions, weather conditions, vehi- “NOTE” which highlights important infor- users, but it also helps to reduce the cle speed in order to prevent acci- mation. Pay particular attention to these wear and tear on your vehicle. dents. highlighted messages. Safe driving depends on:  Turn ‘ON’ the side indicators at least  How quickly you make decisions to 30 meters before taking a turn or NOTE avoid an accident. changing the lane. Indicates additional information that  Decelerate to a safe speed before  Your ability to concentrate. will assist you in gaining the optimum taking turn. Do not apply brakes dur- ing cornering. benefit and care for your vehicle.  How well you can see and judge ob- jects.  When overtaking other vehicles, watch out for the oncoming vehicle. WARNING !  How well familiar you are with your  Never drive under the influence of al- Indicates procedures or information vehicle controls and its capabilities. cohol or drugs. that must be followed precisely in or-  If your vehicle is equipped with info- der to avoid the possibility of severe NOTE tainment/navigation system, set and personal injury and serious damage make changes to your travel route Fatigue is a result of physical or men- to the vehicle. only when the vehicle is parked. tal exertion that impairs judgment.  Program radio presets with the vehi- Driver fatigue may be due to inade- cle parked, and use your pro-

quate sleep, extended work hours,

grammed presets to make radio use strenuous work or non-work activities quicker and simpler. or combination of other factors. Take rest at regular intervals.

1 SAFETY Driving through water Driving on wet roads WARNING ! Do not drive through flooded areas. On wet road or during light showers, “Aq- Judge the depth of water before driving Do not attempt to start the engine if uaplaning” can occur. “Aquaplaning” is through it. Otherwise, water may enter vehicle gets flooded due to water. the loss of direct contact between the the vehicle interior or the engine com- Tow the vehicle to a safe place. Con- road surface and the vehicle’s tires due partment. tact a nearest TATA MOTORS Author- to a water film forming between them. ised Service Centre Steering or braking the vehicle can be If at all the situation demands that you very difficult, and loss of control can oc- have to drive through water then; Driving on a rainy day cur.  Check wiper blades, lights and  Keep engine in higher RPM and crawl There is no hard and fast rule about aq- brakes for proper functioning and the vehicle in low gear. uaplaning. The best advice is to slow condition.  Flowing or rushing water creates down when the road is wet. strong forces. Driving through flow-  Check the tyre treads depth, the con- ing water could cause the vehicle to dition of the tread and tyre. NOTE about trying to drive through flowing  Avoid harsh braking and sharp turns. water. It may cause loss of control and lead If you have driven for a long time in  Lightly apply the brake pedal to dry to a skid. heavy rain without braking, there the liners until the brakes work nor-  For slowing down, shift to lower gears may be a delayed reaction from the mally once you are out of water. and brake gently. brakes when braking for the first  Keep lights ‘ON’ if visibility is poor. time. You have to depress the brake pedal more firmly. Maintain a greater distance from the vehicle in front.

2 SAFETY Night driving Driving on gradients Driving on highway  Ensure that all lights are working and When climbing gradient, the vehicle may Stopping distance progressively in- windshield, window glasses are begin to slow down and show a lack of creases with vehicle speed. Maintain a clean. power. If this happens, shift to a lower sufficient distance between your vehicle  Drive more slowly at night than in the gear and apply power smoothly so that and the vehicle ahead. there is no loss of traction. daytime, as the visual range is re- For long distance driving, perform safety stricted at night. Maintain a speed When driving down a hill, the engine checks before starting a trip and take such that you can stop within illumi- braking should be used by shifting into a rest at certain intervals to prevent fa- nated distance of head lamps. lower gear. Do not drive in neutral gear tigue.  Do not use the high beam unless in- or switch off the engine. evitable. It may dazzle the driver of the oncoming vehicle, thus causing WARNING an accident. !  Use head lamp main/dip beam to On long and steep gradients you alert other road users on turns/ must reduce the load on the brakes cross roads etc. by shifting early to a lower gear. This  Use side indicators for lane change allows you to take advantage of the or turning. engine braking effect and helps avoid overheating of service brakes result- ing in reduced braking efficiency.

3 SAFETY Seat Belts  Position the lap portion of seat belt Fixed rear centre lap seat belt across your thighs, below your abdo- This section of user manual describes When buckling, make sure you hear men. To remove slack, pull up a bit  your vehicle seat belt, airbag and Child a click confirming that the tab is on the shoulder seat belt. To loosen restraints system. Please read and fol- latched into the seat belt lock. To the lap portion seat belt if it is too low all these instructions carefully to tighten it, pull the loose end through tight, tilt the tongue and pull on the minimise risk of severe injury or death. the buckle until the seat belt is com- lap seat belt. A snug seat belt re- fortably adjusted around the hips.  Seat belts are the primary re- duces the risk of sliding under the straints system in the vehicle. All seat belt in a collision. Ensure that occupants, including the driver, the seat belt running over the body should always wear their seat belts (shoulder segment and lap segment) to minimize the risk of injury. does not have any twist. Twisted seat  Sit back and adjust the front seat. belt may not offer effective protec- Make sure that your seat is ad- tion when required. justed to a good driving position and the back of the seat is upright. Releasing the seat belt Buckling the Shoulder Seatbelt To release the seat belt, push the red button on the lock buckle. The seat belt  Grasp the tongue and slowly pull out will automatically retract to its stowed the seat belt over the shoulder and position. If necessary, slide the tongue across the chest. When the seat belt down the webbing to allow the seat belt is long enough to fit, insert the to retract fully. tongue into the lock buckle until you hear a “CLICK” which indicates that the seat belt is securely locked.

4 SAFETY

Seat belt height adjustments  Be careful not to damage or seat belt system. Devices claiming to improve occupant comfort or If the height adjustment is provided in tamper the seat belt webbing or reposition the seat belt can the seat belt, occupant can adjust it to hardware. Inspect the seat belt reduce the protection provided by their comfort, as may be applicable. system periodically, checking for cuts, frays, or loose parts. A frayed the seat belt and increase the or torn seat belt could rip apart in chance of serious injury in a a collision and leave you with no collision. protection. Seat Belts with Pre – tensioner (if  If the seat belt webbing or Equipped) hardware is damaged, get it You can use the pre-tensioner seat belts replaced immediately at TATA in the same manner as ordinary seat Motors Authorized service centre. belts .  Do not insert any items such as The seat belt pre-tensioner system coins, clips, etc. into the seat belt works in conjunction with the buckles, and be careful not to spill SUPPLEMENTARY RESTRAINTS SYSTEM liquids into these parts. If foreign (SRS-Air Bags). materials get into a seat belt In the event of a collision, as may be buckle, the seat belt will not work WARNING necessary, pre-tensioner tightens the ! properly. seat belt so that it fits the occupant’s  Each seat belt assembly must only  Do not wear seat belts over hard, body more snugly. When pre-tensioner be used by one occupant. It is not sharp or fragile items in clothing, activates, there could be some noise recommended to put a seat belt such as pens, keys, spectacles and release of smoke. This is normal around a child, being carried on etc. and there are no health hazards or fire an occupant's lap.  Do not use any accessories on risk. seat belts or modify in any way the 5 SAFETY If the vehicle has been involved in a col- Seat belt Warning Lamp (If WARNING ! lision, get it inspected immediately at Au- equipped) thorised TATA MOTORS SERVICE Center.  The pre-tensioner seat belt The seat belt warning lamp reminds to assembly mechanisms become Use of seat belts for pregnant fasten the seat belt. hot during activation. Do not touch woman the pre-tensioner seat belt assemblies for several minutes WARNING ! after they have been activated. For Driver For Front  Pregnant woman must wear a Passenger If the vehicle has been involved in a correctly positioned seat belt. It is collision, get it inspected immediately at safer for mother as well as unborn  If the driver does not fasten seat belt, authorised TATA MOTORS SERVICE child. seat belt reminder lamp will blink Center.  Pregnant woman should wear the and a buzzer will sound for pre- lap part of the seat belt across the defined duration until the driver’s Seat Belt with Load Limiter (if thighs and as snug across the hips seat belt is buckled. Equipped) as possible. Keep the seat belt low  If front passenger seat is occupied by You can use the load limiter seat belts in so that it does not come across adult and does not fasten seat belt, seat belt reminder lamp will blink the same manner as ordinary seat belts. the abdomen. That way the strong and a buzzer will sound for pre- The seat belt load limiter system works bones of the hips will take the force if there is a collision. defined duration until the front in conjunction with the SUPPLEMEN- passenger seat belt is buckled. TARY RESTRAINTS SYSTEM (SRS-Air  If this system is also provided for Bags). other than Front row seats, apllicable In the event of a collision, as may be nec- above warning will appear until seat essary, load limiter reduces the load on belts are buckled. the rib cage region of the occupant.  If front passenger seat is occupied by child, system may detect occupancy 6 SAFETY and warn with front passenger seat equipped) or ISOFIX with Top Tether (if the vehicle. For installation, please refer

belt warning. It is not taken to mean equipped). CRS manufacturer’s instruction manual. child can occupy front passenger seat and use seat belt. Please refer The harness system of CRS holds the CRS section for recommended child in place, and in a collision, acts to seating position. keep the child positioned in the seat and reduce the risk if injuries. NOTE All children below age of one year must Using unauthorized aftermarket always ride in a rear-facing infant CRS. seat cover may affect function of Keep children in a forward-facing CRS occupant sensor. TATA motors with a harness until they reach the size does not recommended any non- validated seat covers on seats. or weight limit allowed by your CRS man- ufacturer. Child Restraint System (CRS) Once your child outgrows the forward- TATA MOTORS strongly recommends facing CRS, your child is ready for a the use of Child Restraint Systems (CRS) booster seat. for all children up to age of 12 years and Selection and installation of CRS: to be placed at recommended positions only. Children travelling without recom- Always select the CRS that complies with mended CRS and seated at other posi- latest safety standards (AIS072 / ECE tions may face serious injuries in case of R44). The CRS are classified according a collision. to the child's size, height and weight. Select the appropriate CRS for your CRS can be installed in the vehicle using child. Ensure that the child fits properly seat belts and/or ISOFIX only (if in the CRS and it is securely installed in 7 SAFETY Recommended CRS position as Rear Rear per the vehicle matrix Front Mass Out- Out- Rear Group Age Group Passen- The suitability of seat position for car- Group board board Center riage of children and recommended ger LH RH category of CRS is shown in the table below as per the child group. 0 Up to 10 kg Up to 9 months X U U X

X - Seat Position not suitable for 0+ Up to 13 kg Up to 24 months X U U X children in this age group. I 9 to 18 kg 9 months to 48 months X U U X U - Suitable for “universal” category restraints approved for use in this age II 15 to 25 kg Approx. 3 to 7 years X U U X group. III 22 to 36 kg Approx. 6 to 12 years X U U X Universal is a category in the AIS072 / ECE R44 norm.

WARNING !  If a child is seated in the front seat it may cause serious injury or even death during any collision.

8 SAFETY

WARNING ! WARNING ! NOTE

 If your vehicle is equipped with a Do not use an infant carrier or a child  Do not install a booster seat or a front passenger air bag (PAB) and safety seat that "hooks“ over a booster cushion with only the lap do not have PAB deactivation seatback, it will not provide adequate strap of the seat belt. switch, do not install a rear-facing protection in a collision.  Do not install a booster seat or a CRS in the front passenger seat. If After a collision, we recommend to get booster cushion with a seat belt the PAB inflates, a child in a rear seat belts, seats, ISOFIX and top-tether that is slack or twisted. facing CRS could be seriously anchorages (as may be applicable) injured or killed. investigated at TATA MOTORS  Do not put the safety seat belt Authorised service centre. under your child’s arm or behind If you install a CRS in the rear seat, slide its back. the front seat far enough forward so that NOTE the child’s feet do not touch the front  Do not use pillows, books or seatback. This will help avoid injury to A CRS in a closed vehicle can become towels to boost your child’s height. the child in the event of a collision. very hot. To prevent burns, check the  Make sure that your children sit seating surface and buckles before in an upright position. NOTE placing your child in CRS.

Children could be endangered in a  Do not allow children to stand up collision if their CRS are not properly or kneel on either the rear or the secured in the vehicle. Be sure to WARNING ! front seats. An unrestrained child secure the child in the restraint could suffer serious or fatal system according to the  Do not leave unattended children injuries during a collision. in your vehicle. manufacturer’s instructions.  Do not leave any toys or other  Do not modify CRS in any way.

objects loose in the CRS or on the seat while the vehicle is in motion. 9 SAFETY Each CRS should be used for one child only. When PAB deactivation switch (if provided) is turned ‘OFF’, make sure ‘PAB’ operational status lamp illuminates with ignition ‘ON’, indicating that the passenger airbag is NOT operational. If the airbag SRS warning indicator in the instrument cluster illuminates continuously, it means that there is malfunction in the system.

Remove the CRS from front passenger seat and contact your TATA MOTORS authorised service center.

10 SAFETY Supplementary Restraint System ignition mode is “ON”. Air bags are throat. If you have skin or eye irritation, (SRS) (air bags) (if equipped) designed to inflate in collisions when rinse the area with water. For nose or required. In the event of a collision, the throat irritation, move to fresh air. Also The airbag ‘SRS’ system comprises of collision sensors will detect signals, and sometimes the smoke can cause the following components depending if the Airbag ECU judges that the signals breathing problems , in such cases get upon the provided safety features in represent a severe collision, will trigger fresh air promptly. vehicle. the airbags. The inflated air bags provide After inflation, airbag provides a gradual a cushion to the occupants. The air bag  Seat belt Pre-tensioners cushioning effect for the occupant inflates and deflates so quickly that you thereafter deflates. It is not advisable to Seat belt with load limiters  may not even realize that it has drive your vehicle after the airbags have  Driver Airbag activated. The air bag will neither hinder been deployed. If you are involved in  Front Passenger Airbag your view nor make it harder to exit the another collision, the airbags will not be vehicle.  Knee Air Bag in place to protect you. Airbag inflation is virtually instantaneous  Side Airbags and occurs with considerable force,  Curtain Air Bag accompanied by loud noise and smoke,  Airbag ‘SRS’ ECU (Electronic which is normal. The inflated airbag, Control Unit) together with seat belts, limit the  Collision Sensors movement of an occupant, thereby reducing the risk of injury.  SRS wiring harness When an airbag inflates, you may see  SRS Warning lamp some smoke-like particles. The particles  Front Passenger airbag (PAB) are a normal by-product of the process Deactivation switch that generates the non-toxic gas used for The System is active when ignition airbag inflation. These airborne particles switch is in the “ON” position or the may irritate the skin, eyes, nose, or 11 SAFETY Side airbags are mounted in front row Knee airbags are mounted in the NOTE seats for outboard occupants only. dashboard around the knee region of the front row occupants.  Open your windows and doors as soon as possible after collision to Passenger airbag (PAB) reduce prolonged exposure to the deactivation switch and PAB smoke and powder released by operational status indicator (If the inflating air bag. equipped)  Do not touch the air bag storage area’s internal components If it becomes necessary to fit a CRS on immediately after an air bag has the front passenger seat, the passenger inflated. The parts that come into airbag must be de-activated. This switch contact with an inflating air bag can be accessed once front passenger

may be very hot. side door is opened. On the contrary, Curtain airbags are mounted above the when an adult is seated in the front  Always wash exposed skin areas doors along the roof on both sides. thoroughly with lukewarm water passenger seat, ensure that PAB and mild soap. deactivation switch is turned to ‘ON’

position. This will ensure that the passenger airbag is operational in the The driver airbag is mounted in the event of a collision. This switch is centre of the steering wheel. The front operated using the ignition / remote key. passenger airbag is located inside the dashboard in front of the passenger seat. The vehicle fitted with the airbags have suitable indications on steering wheel and on dash board. The word ‘SRS’ is embossed on the airbag covers.

12 SAFETY comfortably extended and their WARNING ! feet on the floor until the vehicle is  Even in vehicles with air bags, you parked and the engine is turned and your passengers must always off. wear the seat belts provided. In  If an occupant is out of position order to minimize the risk and during collision, the rapidly severity of injury in the event of a deploying air bag may forcefully collision. contact the occupant causing  ALWAYS use seat belts and CRS – serious or fatal injuries. during every trip and at all times.  Do not allow the front passenger to place their feet or legs on the Even with air bags, you can be seriously injured or killed in a dashboard. Operational status indicator collision if you are improperly seat  Do not allow the passenger to ride belted or not wearing your seat belt in the front seat when the front when the air bag inflates. passenger air bag OFF indicator is  You and your passengers should illuminated. never sit or lean unnecessarily close to the air bags.  Move your seat as far back as possible from front air bags, while still maintaining control of the vehicle.  All occupants should sit upright with the seatback in an upright PAB deactivation switch position, centred on the seat cushion with their seat belt on, legs 13 SAFETY Not recommended seating position

14 SAFETY collision or sudden stop, causing If your SRS malfunctions, the air bag WARNING ! injuries to occupants in the may not inflate properly during a colli- vehicle. sion thereby increasing risk of serious in-  Never place your arm over the jury or death. If any of the following con-  Coat hooks if provided, must be airbag as a deploying airbag can ditions occur, your SRS is malfunction- used only for that purpose. Never result in serious arm fractures or ing: other injuries. hang heavy items on to those hooks. This could affect  Do not allow the passengers to deployment of the air bags, and WARNING ! lean their heads or bodies onto may lead to severe to fatal doors or place objects between injuries.  The SRS warning lamp does not the doors and passengers when turn ‘ON’ when the ignition switch  ALWAYS contact your TATA they are seated on seats is placed in the ‘ON’ position for MOTORS authorised service equipped with side and/or curtain few seconds. air bags. centre if the vehicle is damaged, even if airbag has not inflated.  The SRS warning lamp stays ‘ON’  Do not place or stick any item/s in after illuminating the vehicle, except at designated  ALWAYS contact your TATA The SRS warning lamp comes locations (such as utility bins, MOTORS authorised service  cup/bottle holders, Boot space centre if any part of an airbag ‘ON’/stays ‘ON’ while the vehicle etc). Loose items may act as a module cover shows sign of is in motion. projectile during a collision and cracking or damage.  The SRS warning lamp blinks cause severe to fatal injuries. when the engine is running.  Please be aware that any unsecured item in your vehicle, such as your pet, unsecured CRS

or a laptop, can become a potential hazard in the event of a 15 SAFETY We recommend the customer to imme- any disability you may have, diately visit TATA MOTORS authorised please contact your Authorized service centre and get the SRS system TATA MOTORS Dealer for inspected if any of the above conditions necessary guidance. occur.  Do not tamper with SRS in any way. This will lead to unexpected WARNING ! performance of system and may cause serious injury or death.  Never make any modifications to your vehicle. The modifications carried out, but not limited to the vehicle frame, bumpers, front fenders, ride height, suspension, seat belts, interior trims, steering wheel (especially holders), are not acceptable. This will affect the intended performance of SRS system.  Fitment of bull bars, seat covers on seats with airbags etc, is strictly prohibited, unless authorised by TATA MOTORS. This will affect the intended performance of SRS system.  If you need to make any modifications to accommodate 16 SAFETY AIRBAGS Deployment Condi- occupant protection during a rear colli- causes a sudden vehicle deceleration. tions (If equipped) sion. Since the collision is underneath the ve- When front airbags (if equipped) Rollovers collision: During a rollover hicle, damage may not be readily visible. collision occupants may float inside the should not deploy? When front airbags (if equipped) passenger compartment, if unbelted. Minor frontal collision: Seat belt of- may not deploy, even with exterior This will increase the risk of injuries. fers adequate occupant protection in visible vehicle damage? low severity collisions. The airbags are Wearing seat belts provide highly effec- triggered only when there is a collision tive occupant protection during rollover The airbags are triggered only when severe enough to trigger the airbags. De- collision. If your vehicle is equipped with there is a collision severe enough to trig- ployment of frontal airbags is not benefi- a rollover sensor, both, seat belt and ger the airbags. The amount of visible ve- cial in low severity collisions. side curtain airbag can provide highly ef- hicle damage is not always the correct fective occupant protection during rollo- indicator for airbag deployment. Some During a side collision, Side collision: ver collision. Front airbags, however, are collisions can result in visible damage occupants tend to move sideways. not designed to deploy in a rollover as but no airbag deployment because the Therefore, deploying frontal airbags in frontal airbags cannot offer any protec- airbags would not have been needed or such situations will not benefit the occu- tion in rollover collision. would not have provided protection even pants. Side airbags, side curtain airbags if they had deployed. (if equipped) are specifically designed to When front airbags (if equipped) de- reduce the injuries that can occur in side ploy with minor or no visible vehicle collision. damage? Rear collision: During a rear collision, The airbags are triggered only when occupants tend to move (rearwards) there is a collision severe enough to trig- away from frontal airbags. Therefore, de- ger the airbags. A severe collision to the ploying frontal airbags in such situations vehicle underbody or suspension may will not benefit the occupant protection. cause airbags deployment. Examples in- Head restraints and seat belts provide clude rough road driving, running into a curb or other low fixed object that 17 SAFETY When a side airbag (if equipped) de- Anti-lock braking system (ABS) - ploys with minor or no visible vehi- (if equipped) NOTE cle damage? ABS regulates brake pressure in such a If the ABS warning lamp is ON while The airbags are triggered only when way that the wheels do not lock when driving then there is a malfunction in there is a collision severe enough to trig- you brake. This allows you to continue the ABS system (the standard brak- ger the airbags. If the airbag system steering the vehicle when braking. ing system will however function) and senses sudden deceleration, a strong the vehicle should be driven cau- collision to the side of the vehicle’s NOTE tiously to the nearest TATA MOTORS Authorized Service Centre. frame can cause a side airbag to deploy. When ABS is active, the driver will In such cases, there may be little feel the brake pedal pulsating, which Electronic brake force distribution is normal.

When a side airbag (if equipped) (EBD) - (if equipped) may not deploy, even with exterior EBD monitors and controls the brake visible vehicle damage? WARNING ! pressure on the wheels to improve driv- It is possible that the side airbag does The stopping distance required for ing stability while braking. not deploy during a collision that results vehicles with ABS may be slightly in visible severe damage. This can occur more than conventional brake sys- when the point of collision is toward the tem but ABS will still offer the ad- far front or far rear of the vehicle or when vantage of helping you maintain di- the vehicle’s crushable body parts ab- rectional control. sorbed most of the collision energy. In ei- However, remember that ABS will not ther case, the side airbag would not compensate for bad road or weather have been needed nor provided protec- conditions or poor driver judgment. tion even if it had deployed. Drive within safety margins, taking into consideration prevailing weather and traffic conditions. 18 OPENING AND CLOSING Flip Key beam, park and roof lamp will turn ‘ON’ 4. Folding key blade in / out for 60 seconds (default setting). This fea- Press button (4) to flip out the key blade. ture helps to find and reach the parked For folding, press the button (4) and fold vehicle or to reach home in dark/ cloudy the key blade inside. condition after parking. Red LED will be flashed on the remote. To switch ‘OFF’ the approach lights, press and release the same button or it automatically turns ‘OFF’ after 60 seconds. Trunk lid opening (if equipped) Electric trunk lid opening can be done through long press (4 sec) approach light 1. Unlock button on remote key. 2. Approach Light /follow me/trunk lid 3. Locking all doors 3. Lock To lock all doors, press lock push-button 4. Key blade in / out button (3) once. Locking will be confirmed by NOTE 1. Unlocking all doors two flashes of turn indicators. Key Blade should not be folded with- To unlock all doors, press unlock push- If lock button is pressed on the remote out pressing the button. Also, it button (1) once. Unlocking will be con- key with the driver door open, locking-un- should not be forced in any direction firmed by single flash of turn indicators. locking takes place with audible warning apart from folding direction to avoid sound. If any other door is open, the ve- 2. Approach light / Follow me damage to Flip Mechanism. hicle gets locked but indicators do not Press approach light button (2) once, low flash.

19 OPENING AND CLOSING Manual operation of central door lock- Also, when unlocked with remote key glowing. The function of the remote ing / unlocking and if no door is opened within 30 sec- gets reinstated immediately when All doors can be locked / unlocked oper- onds, vehicle doors get automatically the user stops pressing the push but- ating driver door using either key blade locked. ton of remote. from outside or knob from inside. Anti-grab / anti-scan coding Important E-Key Features The remote control set of this security Don’t operate Unlock push-button of re- Vehicle search system is protected against the use of mote while in the vicinity of your vehicle, devices called ‘scanners’ and ‘grabbers’ as it could lead to an unintentional un- In vehicle locked condition if lock button which can record and reproduce some locking your vehicle. on remote key is pressed the turn indica- types of remote codes. tors of vehicle flashes 4 times. Don’t use discharged batteries in re- Sleep Mode mote, as it could damage the remote. Automatic activation of immobilizer If remote key is not used for more than a For battery replacement procedure refer If key is removed from ignition, the en- week then its functionalities will turn to maintenance section. gine will be immobilized automatically sleep mode. In such a case, to activate even if you forget to lock the vehicle. the remote key functionalities, open the Don’t remove the battery connection of door mechanically with the key blade. the vehicle while the vehicle has been Auto locking / unlocking of doors / locked by remote. auto relock

Vehicle doors get automatically locked NOTE when all doors are closed and the vehi- In case any button of the key is acci- cle speed crosses 10 kmph. dentally pressed for more than 25 When ignition key is taken out all the seconds, the remote stops function- ing till the time the button is pressed. doors get automatically unlocked. The LED on the Remote also stops 20 OPENING AND CLOSING Doors Locking without a key from inside Opening the doors from inside Door locking / unlocking with key All doors can be opened from inside. To open, pull the door opening knob (1) and Driver door has separate locking facility. then lever (2). All doors can be locked or unlocked from outside using the key.

All the doors can also be locked from in- side by pressing knob (1) on driver door and independently on other doors re- spectively.

Insert the key and turn it clockwise to lock and counter clockwise to open the door.

21 OPENING AND CLOSING Windows Glasses are wound up by pulling the NOTE switch and are lowered by pressing. Power windows (if equipped) Power windows can be operated for 3 minutes in ‘IGN OFF’ position and WARNING ! when key is taken out. While raising the glass, take care to Individual switches avoid fingers/hands getting trapped between glass and the frame. Individual window winding switches have been provided on the front passen- ger and rear doors.

1. Front Window Winding Switch (Right) 2. Rear Window Winding Switch (Right) 3. Front Window Winding Switch (Left) 4. Rear Window Winding Switch (Left) 5. Inhibit Switch

Glasses on all four windows of your vehi- cle can be operated by switches pro- vided on the main control panel located on the driver’s arm rest. They work only when the key is in the ‘IGN ON’ position. 22 OPENING AND CLOSING Inhibit switch Inhibit ON (Pressed position) Manual Window Winding (if equipped) When this switch is pressed the individ- Use window winder handle for lowering ual switches pro- or raising up window glasses manually vided on rear pas- where power windows are not provided. senger doors can- not be operated. It can only be operated by using the win- dow switches on driver's arm rest.

WARNING !  If children operate the windows Inhibit OFF (Released position) they could be get trapped, partic- ularly if they are left unsuper- When switch is re- vised. There is a risk of injury. leased, the individ- ual switches pro-  Activate the window inhibit fea- vided on rear pas- ture when children are travelling. senger door can be When leaving the vehicle, always operated. It can take the key with you and lock the also be operated from the switches on vehicle. Never leave children un- driver's arm rest. supervised in the vehicle.

23 OPENING AND CLOSING Bonnet Opening WARNING ! Always switch off the windshield wip- ers and the ignition before opening the bonnet.

WARNING !

Certain components in the engine 3. Raise the bonnet slightly and with Lift the bonnet up. Pull the bonnet compartment, such as the engine, ra- 4. your finger slide the secondary lock stay rod from its clip and insert the diator and parts of the exhaust sys- lever located under the bonnet cen- free end into the slot. tem, can become very hot. Working in tre to the left side. the engine compartment poses a risk of injury. WARNING ! NOTE  The stay rod can be hot enough to 1. Ensure that the vehicle is in neutral Make sure that the wiper arms are gear with the parking brake applied. burn your finger right after driv- not raised before you lift up the bon- ing. Touch the rod after it be- 2. Pull the bonnet release lever. The net to avoid damaging the wiper comes cool enough. bonnet will pop up slightly. arms and the bonnet.  Insert the stay rod into the hole securely. If the rod drops off, your body may be caught below the bonnet. 24 OPENING AND CLOSING Closing Trunk lid Opening Lever is located on the Option III (If provided) 1. To close the bonnet, hold the bonnet right hand side of the driver seat. Lift the by one hand, disengage the stay rod lever to unlock trunk lid. Lift the trunk lid. and clamp it back properly. Option II 2. Lower the bonnet close to the It can also be opened by using door key, bumper, and then let it drop down. The lock is located on the trunk lid. For closing, pull the trunk lid down and WARNING ! close it with a slight swing. Ensure that the bonnet is locked properly before driving or it can fly up unexpectedly during driving. Trunk lid Option I (If provided) To open the trunk lid, press the switch lo- cated on fascia switch.

NOTE This option will work only in ignition ON condition.

25 OPENING AND CLOSING Option IV (If provided) Fuel lid opening Lever is located on the  Do not use cell phone while refu- right hand side of the driver seat. Lift the eling. lever to unlock fuel flap. Open the fuel  Do not continue adding fuel after cap by turning it in counter clockwise di- the automatic shut ‘OFF’ function rection for fuel filling. operates. If it is equipped on the fuel station. Overfilling the fuel tank could damage the fuel sys- tem.

NOTE

Remove the fuel filler cap slowly, and trunk lid opening can be done through wait for any hissing to stop. The fuel long press (4 sec) approach light button may be under pressure and may on remote key. spray out. Fuel lid For closing, lock the fuel cap and gently If fuel cap needs replacement, ensure push the fuel flap till it gets locked. that it is replaced by a genuine cap at TATA MOTORS Authorized Service Centre only. WARNING !  Fuel vapour is extremely hazard- ous. Always switch ‘OFF’ the en- gine before refueling and never refill near sparks or open flames. 26 DASHBOARD AND FEATURES

Cockpit (MT) 1 A.C. Air vent (Side) 2 Air Bag (PAB) - if fitted 3 A.C. Air vent (Middle) 4 Hazard Warning Switch 5 Combi-Switch 6 Steering Wheel 7 Instrument Cluster 8 Horn pad / Air Bag (DAB) - if fitted 9 Steering Wheel Switches - if fitted 10 Accelerator Pedal 11 Brake Pedal 12 Clutch Pedal 13 Foot Rest 14 Power Socket 15 Cup Holder 16 Parking Brake Lever 17 Gear Shift Lever 18 USB/AUX Port - if fitted 19 HVAC /FATC Control panel(If fitted) 20 Fascia Switches 21 Infotainment System - if fitted 22 Glove Box The above shown image is for reference purpose only. 23 Driver Side Pocket 27 DASHBOARD AND FEATURES

Cockpit (AMT) 1 A.C. Air vent (Side) 2 Air Bag (PAB) - if fitted 3 A.C. Air vent (Middle) 4 Hazard Warning Switch 5 Combi-Switch 6 Steering Wheel 7 Instrument Cluster 8 Horn pad / Air Bag (DAB) - if fitted 9 Steering Wheel Switches - if fitted 10 Accelerator Pedal 11 Brake Pedals 12 Gear Shift Lever 13 Power Socket 14 Foot Rest 15 Cup Holder 16 Parking Brake Lever 17 USB/AUX Port - if fitted 18 HVAC /FATC Control panel(If fitted) 19 Fascia Switches 20 Infotainment System - if fitted 21 Glove Box 22 Driver Side Pocket The above shown image is for reference purpose only. 28 DASHBOARD AND FEATURES Instrument Cluster – Version 1 Tachometer Speedometer

Set knob Mode knob

Driver Information Display

NOTE: All indicators shown may not be applicable to your vehicle.

29 DASHBOARD AND FEATURES Instrument Cluster – Version 2 Tachometer Driver Information Display Speedometer

Set knob Mode knob

Fuel Gauge

NOTE: All indicators shown may not be applicable to your vehicle.

30 DASHBOARD AND FEATURES Speedometer Tachometer

Version 2

Speedometer indicates the vehicle Tachometer indicates engine speed in Version 1 speed in km/h. revolutions per min (rpm).

NOTE WARNING ! At every key IN and ignition ON, the  When engine is accelerated be- Instrument Cluster needles and yond safe ‘rpm’, the tachometer gauges moves to MAX. and returns to pointer turns RED. In such case, re- '0' position. This is a welcome strat- duce the engine RPM immediately. egy and a self-check feature.

31 DASHBOARD AND FEATURES  Never drive the vehicle with engine station if the symbol starts blink- in high ‘rpm’. This may cause se- NOTE ing. vere engine damage.  Check the fuel level when the vehi-  Do not continue adding fuel after cle is on level road. the automatic shut off function is Fuel Gauge  On inclines, curves, during braking operated if it is equipped on the When the ignition switch is in “ON” posi- and sudden acceleration due to fuel pump. The sensor in the fuel tion, fuel gauge gives an approximate in- the movement of fuel in the tank, tank may misjudge the amount of dication of the amount of fuel in the fuel the fuel level display may fluctuate fuel remaining. tank. “F” stands for full and “E” stands or the low fuel warning lamp may for empty. illuminate earlier than usual.

WARNING !  Running the fuel tank too low or empty can cause engine to stall and could endanger User and pas- sengers. User must stop and ob- tain additional fuel as soon as pos- When fuel in the tank is near to empty sible after low fuel warning telltale position, low fuel warning telltale turns turns ON. ‘ON’. Refill the tank as soon as possible.  Low fuel warning symbol will blink If fuel is not filled even after Low fuel warning telltale ‘ON’, first bar in fuel if there is any fault in the system. gauge will start blinking to indicate more Take your vehicle to the nearest severe low fuel warning. TATA MOTORS Authorised service 32 DASHBOARD AND FEATURES Temperature Gauge (if equipped) WARNING !

 High Coolant temp warning Telltale indicates overheating that may damage the engine. Continuing to drive the vehicle when engine over-

When the ignition switch is in the “ON” heating is indicated can result in position, this gauge indicates the engine severe engine damage or fire. coolant temperature. The indicator  Never remove the radiator pres- should stay within the normal, accepta- sure cap from the radiator when ble temperature range between “H” and the engine is hot. “C”. If the indicator approaches “H”, overheating is indicated by red LED bar.

If the coolant temperature reading is very high, the warning telltale flashes with an audible buzzer. In this case, stop the vehicle, switch ‘OFF’ the engine and cool it down for some time. Contact a nearest TATA MOTORS Authorised Ser- vice Centre immediately for rectification. High Coolant temperature warning may come when cooling fans in radiator sections are malfunctioning.

33 DASHBOARD AND FEATURES

Driver Information System Image Description

Indicates total distance travelled by a vehicle. The Odometer reading does not return to “0” when it reaches maximum Odometer value, the display will freeze to maximum value and resettable Note: You can change the Distance unit as Km using SET and MODE buttons.

The trip meter is used to measure the distance travelled on short trips or between fuel stops. It can be reset to “0” Trip meter A & B Trip meter reading becomes “0.0” after it crosses 9999.9 km.

Note: You can reset Trip meter using SET button by long press

Clock When the ignition switch is in the “ON” position, it shows the time.

34 DASHBOARD AND FEATURES

Driver Information System Image Description Indicates the number of days/kilometers in which service is due. If service is overdue, it will display “0” km or “0” days and spanner symbol will blink. Never reset the display between service intervals otherwise, this Service reminder may result in to incorrect readings. Information is retained in the service interval display also after the vehicle battery is disconnected. NOTE: This option is for indicative purpose only. Keep track of your odometer reading and follow the maintenance schedule.

Up or Down arrow shall be displayed on DIS whenever Gear should be put Up or Down. Gear Recommendation This feature is applicable to both AMT and Manual variant. No arrow shall be displayed when the selected Gear is as per the Vehicle dynamics.

“M” indicates Manual Drive mode. Drive Mode (AMT) “Auto” indicated Automatic Drive mode.

35 DASHBOARD AND FEATURES

Driver Information System Image Description

All four door and trunk lid are indicated independently when respective door or trunk lid is open. Note: If any other door is open roof lamp will be ‘ON’ provided that roof Door Ajar lamp switch is in position. ( as applicable) This warning will be indicated when driver door is open. Note: If any other door is open roof lamp will be ‘ON’ provided that roof lamp switch is in position.

Outside Ambient Displays outside ambient temperature in units °C. Temperature

Current gear engaged by the transmission shall be displayed on DIS. This feature is applicable to both AMT and Manual transmission vari- ant. In case of Manual transmission, the gear display is as per the User se- Current Gear Indica- - Neutral lection. IN case of AMT, the display is as per the Automatic selected tion gear.

- Reverse Note: If is displayed, it means ‘Fault’ condition. In such case, take vehicle to authorized TATA MOTORS service station.

36 DASHBOARD AND FEATURES 1. Instantaneous fuel economy 2. Average fuel economy (AFE) for (IFE) NOTE Trip and Trip B  At Every Ignition ON Fuel gauge will be displayed in place of “In- stantaneous Fuel consumption” Bar Graph irrespective of user se- IFE indicates fuel economy of current lection screen. drive when Ignition is turned ‘ON’.  You can Toggle between “Fuel Gauge” and “Instantaneous Fuel Keep IFE bar graph 15 km/l to achieve consumption” Bar Graph using better fuel economy. SET and MODE Button. Average Fuel Economy A/B will reset to  Selection to IFE screen will NOT ‘0’ whenever Trip meter A/B is reset. NOTE be allowed if Fuel is below 1/4th IFE will vary frequently as per driving tank level. Average Fuel Economy will be displayed pattern.  During Vehicle Running if LCD as ‘--.--‘for initial 0.5 km of respective Screen is in “Instantaneous Fuel trip. Once 0.5 km distance is covered, IFE display does not show Fuel Economy consumption” Bar Graph mode & Average Fuel Economy will be displayed. of last drive. th if fuel gauge reduces to 1/4 tank Even after 0.5 km distance covered for The display does not show actual value level then LCD Screen will auto- particular trip, if Average Fuel Economy unless vehicle is moving. matically goes to Fuel Mode. is displayed as ‘--.--‘, then take your vehi-  The maximum value of IFE is 30 cle to TATA MOTORS Authorized Service km/l. No more than 30 shall be in- Centre. dicated on the display even if the actual IFE is higher than 30 km/l.

37 DASHBOARD AND FEATURES 3. Distance to empty (DTE) NOTE NOTE

 AFE value is estimate of fuel  If low fuel waring light turns ‘ON’, economy. It may vary significantly fill the fuel tank immediately re- based upon driving conditions, gardless the value of dis- driving habits and condition of ve- It indicates approximate distance in ‘km’ played DTE. hicle. that your vehicle can travel with availa-  If vehicle is not on level ground  Average Fuel Consumption will ble fuel in tank with current average fuel and negative of battery has been get Reset to ‘0’ when Battery is consumption rate and it is displayed in disturbed, the DTE function may removed and refitted. “km”. not operate correctly. DTE values may vary significantly based  If low fuel warning light turns ‘ON’, on driving conditions, driving habits, and fill the fuel tank immediately re- condition of the vehicle. It is an estimate gardless the value of displayed value of the available driving distance. DTE.  Fill the fuel immediately in case of NOTE DTE shows rEFUEL.  If DTE is displayed as ‘---‘, then take your vehicle to TATA MO- TORS Authorized Service Centre.  The DTE will update with new value when fuel is added more than 4 Litres at a time.

38 DASHBOARD AND FEATURES Driver Information Settings (Version 1)

39 DASHBOARD AND FEATURES Driver Information Settings (Version 2)

40 DASHBOARD AND FEATURES Digital Clock Setting

41 DASHBOARD AND FEATURES

Instrument Cluster Illumination NOTE

 At Every Ignition ON Fuel gauge will be displayed in place of “In- stantaneous Fuel consumption” Bar Graph irrespective of user se- lection screen.

 User can Toggle between “Fuel Gauge” and “Instantaneous Fuel

consumption” Bar Graph using For Instrument Cluster illumination level SET and MODE Button. settings, it is necessary to turn the Park  User selection to IFE screen will Lamp ‘ON’ and then Press the ‘SET’ knob NOT be allowed if Fuel is below on Instrument Cluster. 1/4th tank level. Press ‘SET’ knob to change the illumina- tion intensity level in 5 steps. A delayed  During Vehicle Running if LCD Screen is in “Instantaneous Fuel press on the ‘SET’ knob for a selected in- tensity will confirm it. consumption” Bar Graph mode & if fuel gauge reduces to 1/4th tank

WARNING level then LCD Screen will auto- ! matically goes to Fuel Mode. The Clock and Instrument Cluster Illu-

mination settings should be done only when the vehicle is in stationary

condition for safety purpose. 42 DASHBOARD AND FEATURES Instrument Cluster – Digital Cluster (Version 3)

Tachometer Driver Information Display Temperature Gauge

Set Knob Speedometer Mode Knob Fuel Gauge

NOTE: All indicators shown may not be applicable to your vehicle.

43 DASHBOARD AND FEATURES Instrument Cluster – Digital Cluster (Version 4)

Tachometer Driver Information Display Temperature Gauge

Set Knob Speedometer Mode Knob Fuel Gauge

NOTE: All indicators shown may not be applicable to your vehicle.

44 DASHBOARD AND FEATURES Speedometer Tachometer WARNING !  When engine is accelerated be- yond safe ‘rpm’, the tachometer pointer turns RED. In such case, reduce the engine RPM immedi- ately.  Never drive the vehicle with en- gine in high ‘rpm’. This may cause severe engine damage.

Speedometer indicates the vehicle speed in km/h.

NOTE

 At every key IN and ignition ON, the Instrument Cluster gauges

moves to MAX. and returns to '0' Tachometer indicates engine speed in position. revolutions per min (rpm).

45 DASHBOARD AND FEATURES Fuel Gauge gauge will start blinking to indicate more Temperature Gauge (if equipped) severe low fuel warning. When the ignition switch is in “ON” posi- tion, fuel gauge gives an approximate in- dication of the amount of fuel in the fuel NOTE tank. “F” stands for full and “E” stands Check the fuel level when the vehicle for empty. is on level road. On inclines, curves, during braking and sudden acceleration due to the movement of fuel in the tank, the fuel level display may fluctuate or the low fuel warning lamp may illuminate When the ignition switch is in the “ON” earlier than usual. position, this gauge indicates the engine coolant temperature. The indicator should stay within the normal, accepta- WARNING ! ble temperature range between “H” and Low fuel warning symbol will blink if “C”. If the indicator approaches “H”, there is any fault in the system. Take overheating is indicated by red LED bar. your vehicle to the nearest TATA MO- If the coolant temperature reading is

TORS Authorised service station if the very high, the warning tell-tale flashes When fuel in the tank is near to empty symbol starts blinking. with an audible buzzer. In this case, stop position, low fuel warning telltale turns the vehicle, switch ‘OFF’ the engine and ‘ON’. Refill the tank as soon as possible. cool it down for some time. Contact a If fuel is not filled even after Low fuel nearest TATA MOTORS Authorised Ser- warning telltale ‘ON’, first bar in fuel vice Centre immediately for rectification.

46 DASHBOARD AND FEATURES

WARNING ! The red LED bar and high coolant temperature warning tell-tale Indi- cates overheating that may dam-

age the engine. Continuing to drive

the vehicle when engine overheat-

ing is indicated can result in severe

engine damage or fire.

47 DASHBOARD AND FEATURES

Driver Information System Image Description

Indicates total distance travelled by a vehicle. Odometer The Odometer reading does not return to “0” when it reaches maxi- mum value, the display will freeze to maximum value.

The trip meter is used to measure the distance travelled on short

trips or between fuel stops. It can be reset to “0” Trip meter A & B Trip meter reading becomes “0.0” after it crosses 9999.9 km.

Indicates the number of days/kilometers in which service is due. If service is overdue, it will display “0” km or “0” days and spanner symbol will blink. Service reminder Never reset the display between service intervals otherwise, this may (Package Protected) result in to incorrect readings. Information is retained in the service interval display also after the vehicle battery is disconnected. NOTE: This option is for indicative purpose only. Keep track of your odometer reading and follow the maintenance schedule.

48 DASHBOARD AND FEATURES

Driver Information System Image Description Up or Down arrow shall be displayed on DIS whenever Gear should be put Up or Down. Gear Recommendation This feature is applicable to both AMT and Manual transmission variant. No arrow shall be displayed when the selected Gear is as per the Vehicle dynamics.

Outside Ambient Temperature Displays outside ambient temperature in ºC.

All four door and trunk lid are indicated independently when re- spective door or trunk lid is open. NOTE: If any other door is open roof lamp will be ‘ON’ provided Door Ajar that roof lamp switch is in position. ( as applicable) This warning will be indicated when driver door is open. NOTE: If any other door is open roof lamp will be ‘ON’ provided that roof lamp switch is in position.

49 DASHBOARD AND FEATURES

Driver Information System Image Description

When the ignition switch is in the “ON” position, it shows the Clock time.

“M” indicates Manual Drive mode. Drive Mode (AMT) “A” indicated Automatic Drive mode.

Current gear engaged by the transmission shall be displayed on DIS. This feature is applicable to both AMT and Manual transmission variant. In case of Manual transmission, the gear display is as per the Current Gear Indication - Neutral User selection. IN case of AMT, the display is as per the Auto- matic selected gear.

- Reverse Note: If is displayed, it means ‘Fault’ condition. In such case, take vehicle to authorized TATA MOTORS service station.

50 DASHBOARD AND FEATURES 1. Instantaneous fuel economy 2. Average fuel economy (AFE) (IFE) NOTE AFE value is estimate of fuel econ- omy. It may vary significantly based upon driving conditions, driving hab-

Monitor IFE bar graph to achieve better its and condition of vehicle. fuel economy. Average Fuel Consumption will get Reset to ‘0’ when Battery is removed NOTE and refitted.

IFE will vary frequently as per driving Average Fuel Economy A/B will reset to pattern. ‘0’ whenever Trip meter A/B is reset.

IFE display does not show Fuel Economy Average Fuel Economy will be displayed of last drive. as ‘--.--‘ for initial 0.5 km of respective It indicates fuel economy of current trip. Once 0.5 km distance is covered, Drive when Ignition is turned ‘ON’. Average Fuel Economy will be displayed. Even after 0.5 km distance covered for The display does not show actual value unless vehicle is moving. particular trip, if Average Fuel Economy is displayed as ‘--.--‘, then take your vehi- The indication on the display may be de- cle to TATA MOTORS Authorized Service layed if fuel consumption is affected by Centre. driving pattern.

51 DASHBOARD AND FEATURES 3. Distance to empty (DTE) If low fuel warning light turns ‘ON’, fill the fuel tank immediately regardless the value of displayed DTE.

It indicates approximate distance in ‘km’ that your vehicle can travel with availa- ble fuel in tank.

DTE values may vary significantly based on driving conditions, driving habits, and condition of the vehicle. It is an estimate value of the available driving distance.

NOTE If DTE is displayed as ‘---‘, then take your vehicle to TATA MO-TORS Au- thorized Service Centre.

The DTE will update with new value when fuel is added more than 4 Litres at a time.

52 DASHBOARD AND FEATURES Driver Information Settings

MBSP- Mode Button Short Press

53 DASHBOARD AND FEATURES Driver Information Settings for Illumination and Clock setting

MBSP- Mode Button Short Press; SBLP- Set Button Long Press; SBSP- Set Button Short Press

54 DASHBOARD AND FEATURES

Instrument Cluster Illumination NOTE This is a welcome strategy and a self-

check feature.

For Instrument Cluster illumination level settings, it is necessary to turn the Park

Lamp ‘ON’ and then Press the ‘SET’ knob on Instrument Cluster.

Press ‘SET’ knob to change the illumina- tion intensity level in 5 steps. A delayed press on the ‘SET’ knob for a selected in- tensity will confirm it.

WARNING ! The Clock and Instrument Cluster Illumination settings should be done only when the vehicle is in stationary condition for safety pur- pose.

55 DASHBOARD AND FEATURES

Warning Lamps Color Indicator Remarks 1. Illuminates when ignition is switched ‘ON’. Once engine is started, it turns ‘OFF’. 2. It remains ‘ON’ for any engine related fault that may increase Malfunction Indica- Amber tion Lamp (MIL) emission levels of the vehicle beyond the regulatory norms. Contact a TATA MOTORS Authorised Service Centre for rectifica- tion. 1. Illuminates when ignition is switched ‘ON’. Once engine is started, it turns ‘OFF’. Check Engine Amber 2. Illuminates continuously if a fault arises in Engine Management

System. Contact a TATA MOTORS Authorised Service Centre. 1. Illuminates when the system disables engine start if the original key is not used. 2. Lamp blinks: Vehicle is in immobilized condition when key Red Immobilizer is not inserted.

3. Lamp ON: Problem with key/system. Contact a TATA MOTORS Authorised Service Centre. 1. Illuminates when ignition is switched ‘ON’. Once engine is started, it turns ‘OFF’. 2. Illuminates continuously if excess water is accumulated in the Water in fuel (Diesel) Amber fuel filter. Contact a TATA MOTORS Authorised Service Centre to

drain the water immediately to avoid serious damage to the fuel injection system. 56 DASHBOARD AND FEATURES

Warning Lamps Color Indicator Remarks Illuminates momentarily when ignition is switched ‘ON’ to indicate that the glow plugs are active. It will continuously illuminate when Amber Glow Plug (Diesel) engine is getting preheated. Start the engine only after the indica- tor turns ‘OFF’. Indicates direction indicated by the turn signal. Turn Signal Green Blinks along with buzzer while operating left/right turn indicator only when ignition is switched ‘ON’.

Illuminates when the high beam headlamps are switched ‘ON’ or Blue High Beam flashed.

1. Illuminates when ignition is switched ‘ON’. Once engine is started, it turns ‘OFF’ once required oil pressure is achieved. 2. Illuminates continuously if there is insufficient oil pressure. Low Oil Pressure Red Stop the vehicle as soon as safety permits and switch off the

engine. Check engine oil level and top-up if required. Contact TATA MOTORS assistance before starting the engine.

Illuminates when ignition is switched ‘ON’. Once engine is started, it turns ‘OFF’. Red Battery charging It will continuously illuminate when there is malfunction of charg- ing system. Contact a TATA MOTORS Authorised Service Centre.

57 DASHBOARD AND FEATURES

Warning Lamps Color Indicator Remarks Illuminates momentarily when ignition is switched ‘ON’. Once park- ing brake is released, it turns ‘OFF’. If it remains ‘ON’, it indicates Park Brake / Brake Fluid Red 1. Brake fluid level is low. Low / EBD Fault 2. Park brake is applied & turns ‘OFF’ when it is released. 3. ABS/EBD system has a fault. Indicates that seat belt is not fastened when ignition is ‘ON’. It will be continuously 'ON' if the seat belt is not fastened. When the vehicle speed goes above 15 kmph seat belt alarm will be audible. If seat belt is not fastened and vehicle speed goes above 15 Kmph, then final warning will start with telltale flashing and Audio chime for 90 seconds. After 90 seconds, telltale will be ON and Audio chime Driver seat belt warning Red will be OFF. Note:  Telltale will turn off either when seatbelt is buckled or Reverse gear is engaged when it is in initial warning stage.  When it is in final warning with Chime ON, the telltale will be OFF on fastening the seat belt or engaging the reverse gear.

58 DASHBOARD AND FEATURES

Warning Lamps Color Indicator Remarks Illuminates momentarily when ignition is switched ‘ON’. Airbag status Red It will continuously illuminate when there is malfunction of airbag (SRS) system. Contact a TATA MOTORS Authorised Service Centre immediately. Illuminates momentarily when ignition is switched ‘ON’. EPAS (if applicable) Amber Illuminates when there is a fault in the EPAS. Contact a TATA MO- TORS Authorised Service Centre immediately. If the coolant temperature reading is very high, the warning Telltale flashes with an audible buzzer. In this case, stop the vehicle, switch ‘OFF’ the engine and cool it High Coolant Tempera- Red down for some time. Contact a nearest TATA MOTORS Authorized ture Service Centre immediately for rectification. High Coolant temperature warning may come when cooling fans in radiator sections are malfunctioning. Illuminates momentarily when ignition is switched ‘ON’. Illuminates continuously if there is any malfunction in ABS. Normal braking ABS (if applicable) Amber system will be operational without assistance of ABS. Contact a TATA MOTORS Authorised Service Centre immediately.

59 DASHBOARD AND FEATURES

Warning Lamps Color Indicator Remarks

Illuminates momentarily when ignition is switched ‘ON’. Illuminates when fuel level is low. 1st bar on fuel gauge will start blink- ing when fuel level is low. Refill the fuel tank as soon as possible. Low Fuel Amber IMPORTANT: The warning light will start flashing if there is any fault in the fuel system. Contact a TATA MOTORS Authorised Service Centre immediately.

ECO ECO indicates Economy drive. This mode is used to achieve better fuel Green (For MT) (If applicable) economy.

CITY mode is default mode. This mode is used to achieve optimum CITY Blue torque.

SPORT This indicates comes when vehicle is in a SPORT mode. It is applicable Amber

(For AMT) (If applicable) only in AMT. This mode is used to product more torque from engine.

Illuminates momentarily when ignition is switched ‘ON’. Illuminates continuously when there is a fault in Automatic AMT Fault Amber (If applicable) Manual Transmission system. Contact a TATA MOTORS authorized Ser- vice Centre immediately.

60

DASHBOARD AND FEATURES

Warning Lamps Color Indicator Remarks

Illuminates when ignition is switched ‘ON’ and goes ‘OFF’ after 4 Seconds. The warning lamp remains ‘ON’ if the front passenger seat is occupied Front passenger Seat Red and seat belt is not fastened. Belt Indicator If seat belts remains unbuckled and vehicle speed goes above 15 kmph, then final warning will start illuminates with audio chime for 90 seconds continuously.

Illuminates when ignition is switched ‘ON’ and goes ‘OFF’ after 4 Seconds. When the vehicle speed cross 80 km/hrs. then Speed limit Warning in- dicator turn ‘ON’ along with for every 2 minute chime shall be sounded (Audible warning). If vehicle speed crosses 120 km/hrs. then along with Speed limit Warn- Speed limit warning in- Amber ing Indicator, Chime will start continuously ON till the vehicle speed is dicator above 115 km/hrs. If vehicle speed reduced below 115 km/hrs, chime will be sounded one beam per two min. but speed limit warning indicator will remains ‘ON’ continuously. When the vehicle speed is reduce below 75 km/hrs. then Speed limit Warning Indicator along with chime will gets turns ‘OFF’.

61 DASHBOARD AND FEATURES

Warning Lamps Color Indicator Remarks The warning light or symbol switches on constantly to indicate that the DPF needs to eliminate the trapped pollutants (particulate mat- ter) through the regeneration process, it therefore does not indicate a malfunction. The warning light or symbol remain off during the en- tire DPF regeneration and light up only when driving conditions re- quire the driver to be notified. To switch off the warning light or sym- DPF Lamp (Diesel) Amber bol, keep the car running until regeneration is complete (ideally at rd 3 gear, 60 km/hr. with engine speed over 2000 rpm). The process normally takes about 20 minutes. Note: Failure to be observed the appropriate procedure for a long distance when the DPF warning light comes ON, can cause the warning light (MIL) to come ON. In that case, please contact nearest TATA authorized service center to restore correct DPF operation.

62 DASHBOARD AND FEATURES Audio Reminders Reverse gear reminder AMT fault Reminder Key in reminder When Reverse Gear is engaged, audio If Fault occur in AMT, 3 second audio warning for 1 sec will alert you. warning will alert you. While leaving your vehicle, if you forget the key inside the vehicle in Ignition Driver seat Belt reminder Drive mode chime ‘OFF’ position, buzzer will provide audio If seat belt remains unbuckled and vehi- Manual Transmission: warning. Remove Key to stop the warn- cle speed goes above 15 km/ hrs, Final When drive mode changes from City to ing. Waring will start. Audio Chime will con- Eco mode or Eco to City mode, audio tinue for 90 seconds. Seat belt telltale Park lamp ‘ON’ reminder warning will be alert for one second. will be flash when audio alarm is active. While leaving your vehicle, if you forget Automatic Transmission: to turn ‘OFF’ the headlamps, buzzer will Front passenger seat belt reminder When Drive mode changes from Manual provide audio warning. Switch ‘OFF’ Park If Front passenger is present & its seat to Auto or Auto to Manual, audio warning Lamps to stop the warning. Do not forget belt remains unbuckled and vehicle will be alert for one second. to turn ‘OFF’ your headlamps as it may speed goes above 15 km/ hrs. Final drain your vehicle battery. Warning will start. Audio Chime will con- Park brake ‘ON’ reminder tinue for 90 seconds. Seat belt telltale will be flash when audio alarm is active. If Park Brake is applied and vehicle is driven, Tell tale will turn ‘ON’ and buzzer NOTE will provide audio warning continuously. Disengage the park brake to stop audio Buckle the seat belt to stop Audible warning. warning.

63 DASHBOARD AND FEATURES Combi-Switch (RH Stalk) 3. High beam - Move the lever forward point where the turn signal light begins to select the High Beam function. to flash, but the lever does not latch. The Pull the lever back to normal for low turn signal will flash 3 times automati- cally. beam. 4. High beam Flash (spring return) 7. Head lamp leveling rotary switch To flash the high beam, pull the lever towards you from the normal posi- tion. It will return to its normal posi- tion when you release it. 5. Headlamp Rotary Switch

i) OFF Position 1. Left Turn signal - Move the lever All lamps will remain ‘OFF’. fully upward. ii) Parking Lamp Inner rotary switch on right hand stalk is 2. Right Turn signal - Move the lever provided for head lamp leveling. With the fully downward. Rotate stalk to turn ‘ON’ the Parking lamps. inner rotary switch, Head lamp leveling can be done with head lamp in Low NOTE iii) Low Beam Beam and in ‘ON’ position. Select cor- rect position before start of trip and ve- Rotate stalk to turn ‘ON’ the Low When the turn is completed, the sig- hicle is stationary. Depending upon the Beam function. nal will cancel and the lever will re- number of passengers and luggage in turn to its normal position. 6. Lane Change Signal the vehicle headlamp focus may change. This can be adjusted by rotating the To signal a lane change, move the lever slightly up or down respective to the knob to one of the 3 level positions. 64 DASHBOARD AND FEATURES Combi-Switch (LH Stalk) 2) Slow Wipe NOTE Push the stalk towards position (2) for continuous slow wipe. When you crank the engine, the sup- 3) Fast Wipe ply to washer motor is momentarily cut off. Push the stalk towards position (3) for continuous fast wipe. Fascia Switches – 4) Flick wipe (spring return) Option I Pull the stalk downwards and hold it for continuous wipe, Fascia switches are provided on the cen- the wiper continuously wipes ter console above HVAC control panel. across the windshield at low speed till the stalk is released. 0) ‘OFF’ Position 5) Front Windshield Washer The wiper is switched ‘OFF’.  Pull the lever little longer, washer fluid will be 1) Intermittent wipe sprayed on the windshield. Push the stalk upwards to operate inter-  The windshield wipers operate for 3 mittent wipe. cycles after the lever is released and 1 more cycle after 5 seconds. Inner rotary switch on left hand stalk is provided for intermit- tent front wiper delay. The switch has 5 delay timers. 1. Front fog lamp switch 2. ECO mode switch 3. Electric trunk lid 65 DASHBOARD AND FEATURES

Option II Electric Trunk lid 1. Electric trunk lid 2. Front fog lamp switch To open the trunk lid, press 3. ECO mode switch the switch located on fascia 4. Center locking switch switch. Front Fog Lamps Rear Window Demister (if equipped) In conditions where visibility is poor due to fog, snow or The switch turns the rear rain, the fog lamps improve window demister ON/OFF. It visibility as well as making it easier for operates when engine is run- other road users to see you. ning. The system will be deactivated af- ter 15 min of continuous operation. 1. Rear window demister switch It turns ‘ON’ when the front fog lamp 2. Front fog lamp switch switch is pushed in with ignition ‘ON’ and An indicator on the switch will be illumi- nate when the rear window demister is 3. Electric trunk lid position and parking / head lamp is ‘ON’. An indicator on the switch will be illumi- ‘ON’ Option III nated when the front fog light is ‘ON’. Center locking switch ECO mode Switch (if equipped) All the doors can be lock Refer DRIVE MODES chapter and unlock from inside in ‘STARTING and DIVING’ the vehicle by pressing section. this switch. NOTE All doors are closed while using the center locking switch.

66 DASHBOARD AND FEATURES Steering Wheel Switches (LHS) Steering Wheel Switches (RHS) Mic (if equipped) (if equipped)

Phone receive A mic is provided on roof interior above Volume - To increase (+) / decrease (-) This button is used to accept incoming driver seat position. volume of music system / radio. call when a cell phone is connected via Mute / phone reject Bluetooth. Speakers (if equipped) To reject or hang up a phone call. It is NOTE Speakers and tweeters are provided on also used to mute the volume of music models with infotainment system. While system / radio. For more information on steering provisions are given for music system Seek forward / backward wheel switches refer Infotainment and speakers on versions without info- manual. To change radio channels. tainment system. Source - To select the required source in the infotainment (USB, AUX, AM, FM).

67 DASHBOARD AND FEATURES Infotainment System (Option I) Power Socket (if equipped) NOTE For more information on Infotain- ment system refer below link http://service.tatamotors.com/con- tent/owners-manual.

USB/AUX Port (if equipped)

Two power sockets are provided. The (Option II) power socket will work when the ignition switch is in the “ACC” or “ON” position. This socket can be used to provide 12V (10A) power for electrical accessories.

NOTE

Connect your portable digital music play- Use of inappropriate electrical ac-ac- ers, pen drives etc. to this socket for cessories can cause damage to your playing music tracks through the vehi- vehicle’s electrical system. Make cles music system. sure that any electrical accessories you use are designed to plug into this type of socket. 68 DASHBOARD AND FEATURES Antenna (Option II) Roof Lamp (Option I)

Shark FIN antenna is provided on the roof at rear end. Interior roof lighting lamp is provided on Antenna is located on the roof. Turn an- the roof with inbuilt switch. tenna counter clockwise to remove from The switch has three positions: vehicle, if required. ON - The lamp will turn ‘ON’ as long as the switch is in this

position.

DOOR - In this position the lamp turns ‘ON’ with dim- ming when either of the doors are opened. When the last door is closed, the lamp will remain ‘ON’ for 69 DASHBOARD AND FEATURES 25 sec and turns ‘OFF’ with dimming. Roof Grab Handle Boot Lamp (if equipped) This helps settling in the seat and in- serting the key in the ignition switch. When the key is turned to the ‘IGN’ po- sition, the lamp goes ‘OFF’ immedi-

ately. OFF - In this position the

lamp will remain ‘OFF’.

Roof grab handles are provided on all Boot lamp is provided in the luggage seats except driver’s seat. This helps in compartment to illuminate the luggage comfortable positioning of passengers area. during a journey. Switch is provided on lamp to turn ‘ON’/ ‘OFF’ boot lamp. If switch is re- tained in ‘ON’ position, Boot lamp will turn ‘ON’ automatically on opening the trunk lid.

70 DASHBOARD AND FEATURES Tag Holder

Tag holder is provided near the front windshield for ease of displaying toll, parking tickets, ID’s, passes, labels etc.

71 DASHBOARD AND FEATURES

72 STOWAGE AREAS Storage Compartments

1) Glove box 4) Driver side pocket 7) Trunk lid compartment 2) Utility pockets on front doors 5) Center console 3) Utility pockets on rear doors 6) Foldable arm rest

73 STOWAGE AREAS 1) Glove box vent by rotating the knob, whenever cooling is not required. 2) Utility pockets on front doors 3) Utility pockets on rear doors Utility pockets are provided on front and rear doors and it can be used to keep magazines/books, water bottles etc.

4) Driver side Pocket

1. Vent - Chiller glove box (If applicable)

2. Laptop holder To open - Press the knob and open the 3. Pen / Visiting card holder glove box flap. To close - Fold glove box flap upwards NOTE until it engages. On selected models, cooling facility- ty is also provided. It cools the glove box only when the AC is ‘ON’.

Chiller glove box (If applicable) Upper Glove Box is provided with a cool- You can keep suitable items in the space ing facility. It cools the glove box only provided. when the front A/C is ON. Shut OFF the

74 STOWAGE AREAS d) Bottle holder 7) Trunk lid Compartment NOTE 6) Foldable arm rest Use cups, containers, bottles of right size and which have lids. The drinks A foldable arm rest has been provided in could otherwise spill. the rear seat. It also has two cup holders, which can be accessed by opening the 5) Center console cover. When not required, fold the arm- rest back into the seat.

Store the luggage in trunk lid. WARNING ! Distribute the items of luggage as evenly as possible.

Position heavy loads as far forwards a) Stowage compartment as possible and as low down in the Stowage compartment provided for trunk lid as possible. keeping cell phones, iPod’s, chargers NOTE The load must not protrude above the etc. Remove all items and cups before luggage cover. Never allow occu- b) Cup holder c) Coin storage folding the cup holders pants to travel in the luggage com- partment.

75 STOWAGE AREAS Card holder (If applicable) Coat hook WARNING ! A pocket is provided on the back of the Coat hook is provided on rear passenger driver side sun visor to keep cards, pa- right side grab handle. The coat hook cannot restrain heavy pers etc. objects or items of luggage. Never hang hard, sharp-edged or fragile objects on the coat hook..

Collapsible hook Collapsible hook is provided for hanging carry bags etc. Load up to 2 kg is permis- sible.

NOTE

Keep the sun visors in their original position when not in use or else, they may block driver’s vision.

76 CLIMATE CONTROL The HVAC is operational when engine is running and blower is ‘ON’. The Climate control regulates the temperature in the vehicle interior and filters dust particles. You can manually set the desired temperature Air Distribution- The air is distributed through the vents in the passenger compartment as shown below:

77 CLIMATE CONTROL Air vents HVAC Controls (if applicable) A. Air distribution control Air vents are provided on dashboard. Air flow and its direction can be adjusted with the help of knob provided on re- spective vent.

This is to select the air distribution pat- tern as described in the table.

Directs air through the cen- A. Air Distribution Control ter and side air vents B. Blower Speed Control Directs air through the cen- C. Temperature Control ter, side and foot well vents

D. Air Intake Selector Directs air through the foot E. AC ON/OFF Switch well air vents Directs air through the de- froster & foot well vents

(Default fresh air mode) Directs air through the de- froster vents (Default fresh air mode)

78 CLIMATE CONTROL B. Blower Speed control increase the temperature, turn the dial Fresh Air mode: (Indicator light ‘OFF’) to the right. Fresh air is drawn into the vehicle. Always use when: D. Air intake selector OFF HIGH Press the switch to activate / deactivate  Discomfort is felt or windows are recirculation mode. fogging up.  Using or air flow modes during demist / defrost. This is to turn ‘ON’ the blower and select desired blower speed.  Using normal heating mode. Press to ‘ON’ or ‘OFF’ C. Temperature control E. AC ON/OFF Recirculation mode: (Indicator light ‘ON’) Air in the passenger compartment recir- LOW culates. No fresh air enters the compart- HIGH ment. Always use when: Press the switch to activate / deactivate The temperature control dial allows you the climate control. The indicator lamp in to adjust the temperature. To lower the  Driving on a dusty road or through the button will light up when climate con- temperature, turn the dial to the left. To tunnel. trol is activated. On signals or slow traffic to avoid  When AC is switched ‘ON’, engine idling NOTE traffic pollution. RPM increases marginally to adjust the  Maximum cooling is required. AC compressor load. The AC can be switched ‘ON’ only if the blower is ‘ON’ and engine is running. When desired temperature is achieved AC trips ‘OFF’ automatically.

79 CLIMATE CONTROL Recommended basic settings of the control elements of air conditioning system for the respective operating modes. These may vary depending on individual requirements and weather conditions.

Control Knob Position Button Position

A. Air Flow Direction B. Blower Speed C. Air Temperature D. Air Intake E. AC ON / OFF

Functions

Normal heating or 2nd or 3rd dot Desired temp. Fresh air mode. Switched OFF To MAX speed Briefly switch ON to To the right up to the and then 2nd or Fresh air mode Switched OFF Quick heating stop 3rd dot then Recirculation mode Recirculation 1st to 3rd dot Desired temperature Switched ON Normal Cooling or mode To MAX speed To the left up to the Recirculation and then 2nd or Switched ON Quick Cooling or stop mode 3rd dot Fresh air mode Switched ON 2nd or 3rd dot Desired temperature Demisting (Default) (Optional) Fresh air mode Switched ON To MAX speed Desired temperature Defrosting (Default) (Optional)

80 CLIMATE CONTROL  While starting the vehicle itself af- NOTE ter long duration (more than 15  Condensation may drip from the days), following procedure needs underside of the vehicle when it is to be followed to meet AC perfor- in cooling mode. Traces of water mance. on the ground are normal and are - Start the vehicle with AC & Blower

not a sign that there is a malfunc- in OFF condition in idling for 2~3 tion. minutes. Then switch ON the AC & Blower  Ventilate the vehicle for a brief pe- - riod during warm weather. This and run it for another 2~3 will speed up the cooling process minutes in idling for proper circu- and the desired vehicle interior lation of refrigerant & oil to lubri- temperature will be reached cate the internal parts of AC sys- quickly. tem.  Never cover the air vents or air in-

take grilles in the vehicle interior.

 If the AC is not used for a long pe- riod, such as during winter, it may not give the best performance when you start using it again. Op- erate the AC at least once a month to maintain optimum perfor- mance.

81 CLIMATE CONTROL FULLY AUTOMATIC TEMPERATURE CONTROL (FATC) GENERAL DESCRIPTION (if applicable) FATC system controls the in-cabin Temperature of the vehicle automatically and provides maximum passen- ger convenience regardless of outside weather condi- tions.

NOTE If the display flashes ‘ERR’ in periodic pattern (Dis- play will show ‘ERR’ for 5 sec. and set tem-prema- ture for 30 sec.), It indicates FATC malfunctioning. Switch over to manual mode and con-tact a TATA MOTORS authorized service Centre.

1. AC compressor ON/OFF button 2. Blower speed control knob

3. Econ (economy mode) button 4. Maximum defrost button 5. Rear window demister button 6. Fresh air / recirculation button 7. Air distribution (mode) button 8. OFF mode 9. Auto on selection button 10. Temperature control knob

82 CLIMATE CONTROL DISPLAY UNIT 1. AC COMPRESSOR ON / OFF BUTTON:

Press the AC compressor ON/OFF button to turn the air conditioning ON or OFF. Also, when the display is not in climate You will see AC text on the display, when mode then climate information will be FATC display is shown on infotainment AC is ON. displayed on the all-time display provide display screen. on the bottom bar. 2. BLOWER SPEED CONTROL FATC functions can be controlled using KNOB: both the FATC control panel and the touch screen display. Whenever the user presses any push button or turns the rotary knob, then the display unit will show the relevant Cli- mate Information

A. Rotate the knob clockwise to in-

crease the blower speed up to MAX 7 speed, where as anti-clockwise would re- duce the speed up to ‘SPEED 1’. 83 CLIMATE CONTROL B. In ‘AUTO’ mode, the FATC system will 4. MAX DEFROST BUTTON: 6. FRESH AIR / RECIRCULATION regulate the blower speed automatically. BUTTON: A. This button directs 3. ECON BUTTON: the main airflow to- A. When the recirculation wards windscreen for Button or LED is switched faster defrosting. (It ‘ON’, air from the vehi- also overrides any mode selection you cle’s interior is sent may have made.) throughout the system.

B. When you turn off the button, the sys- B. When the recirculation button is During ECON AC operation, the system tem returns to its former settings. switched off, air is brought in from out- automatically cuts off compressor at a side of the vehicle (fresh mode). When- NOTE higher temperature than normal AC. The ever discomfort is felt, switch to fresh air operation can be used during mild For your safety make sure you have a mode. weather conditions for better fuel effi- The system should be used with recircu- ciency. clear view through all the windows before driving. lation air mode for faster heat up and cool down, however keeping the system NOTE 5. REAR WINDOW DEMISTER in recirculation mode, particularly with BUTTON: AC OFF, can cause the windows fog up. The outside air intakes for the cli- A. This button turns the rear window de- mate control systems are at the base 7. AIR DISTRIBUTION (MODE) mister ON or OFF. The system will be BUTTON: of windscreen. Keep this area clear deactivated after 15 min of continu- from leaves and other debris. ous operation. A. In AUTO mode, the FATC system will regulate Comfort level may be compromised dur- the mode automatically. ing this operation. By pressing ECON but- Ho ever, user override is ton text will be displayed on display.

84 CLIMATE CONTROL possible with the use of MODE button to 8. “OFF” BUTTON: heated air that will, as quickly as pos- select the desired airflow mode. sible, raise or lower the interior tem- perature to your preference. Each time you press the MODE button, the display shows the mode selected. D. When you set the temperature to its lower limit (Lo) or its upper limit (Hi), Press the OFF button to switch OFF The the system runs at full cooling or Air flows from the cen- system. OFF will be displayed on the dis- heating only. It doesn’t regulate the ter and side air vents play. interior temperature. Air flows from the cen- 9. AUTO ON SELECTION BUTTON Semi-automatic Operation ter, side vents and foot You can manually select various func- well vents tions of the climate control system when it is in fully automatic mode. All other Air flows from mainly features remain automatically con- foot well vents trolled. Making any manual selection causes the word ‘AUTO’ in the display to Air flows from the de- To put the automatic climate control in fully automatic mode: go OFF and overridden setting is dis- froster and foot well played. System will remain in semiauto- vents (always select A. Press the ‘AUTO’ button. matic mode till ‘AUTO’ is re-pressed. fresh air mode) B. Set the desired temperature by turn- Air flows from the de- ing temperature control knob. The froster vents (always display will show all the functions select fresh air mode) during ‘AUTO’ mode. C. The system automatically selects the

proper mix of conditioned and / or

85 CLIMATE CONTROL 10. TEMPERATURE CONTROL KNOB:

Turning the temperature control knob clockwise increases the temperature of the air. The desired temperature will be increased by steps of 0.5ºC. User can se- lect temperature range from 18ºC to 30ºC. Whereas the anticlockwise direc- tion decreases the temperature. When you set the temperature to its lower limit (Lo) or its upper limit (Hi), the system runs at full cooling or heating only. It doesn’t regulate the interior tem- perature.

86 CLIMATE CONTROL

Functions Control Knob Position Button Position

Normal Desired Desired Switched Switched OFF OFF OFF ON heating Speed Temp. OFF OFF

Quick Max. To the right Switched Switched Switched Switched OFF ON heating speed up to the stop OFF OFF OFF OFF

Normal Desired To the right up Switched Switched Switched Switched ON ON Cooling speed to the stop OFF OFF OFF OFF

Quick Max To the right up Switched Switched Switched Switched ON ON Cooling speed to the stop OFF OFF OFF OFF

Max To the right up Switched Switched Switched Switched Demisting OFF OFF speed to the stop OFF OFF OFF OFF

Max To the right up Switched Switched Switched Switched Demisting OFF OFF speed to the stop OFF OFF OFF OFF

87 CLIMATE CONTROL HVAC Sensors 2. In-car sensor on control panel. If your vehicle is parked under the sun, you can cool it down fast by following the HVAC system is fitted with three sensors steps given below: 1. A solar sensor on top of the dash- A. Start the engine. board at the right hand side of de- B. Turn on A/C by pressing the button. froster grill Make sure the temperature control is set to maximum cool. In case of FATC set temperature to ‘Low’

mode. 3. Outside Ambient Temperature (OAT) C. Set the fan to maximum speed. (for sensor located under the front ETC, manual HVAC variants) bumper grill. D. Open windows half, set air direction towards face and fresh air mode. NOTE E. When the interior has cooled down to a more comfortable level, close  Do not cover or spill any liquid on windows and set the controls as re- sensors. quired in normal cooling, with recir- culation mode ON.  Do not cover sensor, this may cause the sensor to malfunction.

This may lead to FATC not func- tioning to desired level.

88 STARTING AND DRIVING Pre Driving Checks Daily check Weekly check Make sure that  Tyres for abnormal wear, cracks or  Engine oil level damage and embedded foreign ma-  Windshield, windows, mirrors, lights, terial such as nails, stones, etc.  Coolant level and reflectors are clean and unob-  Traces of fluid and oil below vehicle. structed.  Brake fluid level  Tools kit, jack & handle, warning tri-  Windshield washer fluid level angle, owner’s manual, first aid kit NOTE  Fuel level and vehicle documents are available Water dripping from the air condition- and stored at their locations. ing system after use is normal. NOTE WARNING  All lamps, wipers, wiper blades and ! horn for proper operation. Check the tyre pressure regularly in- cluding spare wheel. Never put any mat on top of the floor  All switches, gauges and tell tales are carpet near pedal region. working properly.  All doors, engine bonnet and trunk lid Adjust: are securely closed and latched.  Seats, head restraints (if equipped)  All of your passengers are properly and steering wheel position. restrained. You and your passengers should always wear seat belts.  All the mirrors properly.  Objects, luggage or loads are se- cured properly against slipping or tip- ping.  Sufficient fuel for the trip.

89 STARTING AND DRIVING Driving Tips Personal driving style  Driving safety systems are merely aids designed to assist driving. You Fuel consumption, engine, transmission,  Do not depress the accelerator pedal are responsible for the distance to brake and tyre wear are mainly affected when starting the engine. the vehicle in front, for vehicle speed by below factors:  Do not warm up the engine when the and anticipating braking in good vehicle is stationary.  Operating conditions of your vehicle time.  Always adapt your driving style to suit  Your personal driving style the prevailing road and weather con- WARNING Operating conditions: ditions and maintain a safe distance ! from the vehicle in front. Drive care- You could lose control of your vehicle Avoid frequent start and stop as  fully. if you try to adjust the driver's seat, these increase fuel consumptions.  Avoid frequent, sudden acceleration head restraint, mirror, steering wheel  Always make sure that the tyre pres- and braking. and fasten the seat belt while driving. sures are correct.  Select appropriate gear according to There is a risk of an accident. varying speeds and load conditions.  Do not carry any unnecessary weight.

 Regularly service your vehicle and NOTE adhere to the recommended service maintenance schedule. Do not rest your foot on the clutch pe- dal while driving.

 Switch ‘OFF’ the engine in stationary traffic or at signals.  Keep an eye on the vehicle's fuel con- sumption.

90 STARTING AND DRIVING Recommended fuel economy  Avoid high speed when cornering or  Keep the vehicle clean. Get rid of the speeds (For MT) turning. not in use luggage/stuff lying in the  Depress the clutch fully while shifting boot etc. Gear Speed (km/h) gears.  Regularly inspect your vehicle for any Diesel Petrol  Make sure that vehicle is completely leakages, worn out wires by rat bites stationary before you attempt to shift etc. 1 15 15 in reverse gear.  Always follow periodic & regular ser- 2 25 30  Drive slowly on wet roads. vice schedule of the vehicle.  In places with high dust content (e.g. 3 45 45  You can get extra braking from the engine by shifting to a lower gear. Gurgaon, Jaisalmer etc.), Clean air fil- 4 65 65 This can help you to maintain a safe ter element more frequently. 5 80 80 speed and prevent your brakes from  Drive smart and smooth in an antici- overheating specially while going patory manner. Select driving mode Good driving practices down a hill. to suit your style.  Do not accelerate excessively when  Slow down before shifting to a lower Tips for obtaining better fuel effi- you are in lower gears (1st or 2nd). Be gear. This will help avoiding revving ciency gentle on the accelerator when you of the engine causing damage.  Always maintain the specified tyre are in traffic. In lower gear, opening  Avoid frequent brake application pressure during fuel top-ups and also more throttle will shoot the engine which can cause overheating of before a long trip. Vehicle running RPM keeping the vehicle still at lower brakes. with low tyre pressure will consume speeds which indirectly implies less  Slower the vehicle speed while trav- more fuel than the one running with distance with more fuel. elling in cross winds. This gives much specified tyre pressure. better control over the vehicle.

91 STARTING AND DRIVING

 Be in the maximum possible higher time is high (typically more than 30 Gear Diesel Petrol gear at a given speed. This reduces sec). the engine operating speeds which  While driving on highways, drive with Speed(km/h) Speed(km/h) means the engine is running at lower windows closed. The more you open 1 20 20 rpm (Revolutions per Minute) for the the windows the higher will be the same vehicle speed. Lesser the num- resistance to the vehicle at higher 2 30 40 ber of engine revolution lesser the speeds which will reduce the fuel ef- 3 50 60 fuel burned. ficiency. 4 70 80  Avoid harsh braking.  Do not over speed; follow the speed  Maintain healthy driving habits & limits. More the speed, higher the 5 90 100 while decelerating, do coasting in external resistance on the vehicle Avoid heavy loads, e.g. driving at full gear and not in neutral or with clutch which will finally result into unneces- throttle, during this period. Change pedal depressed. sary consumption of fuel. gears judiciously.  Consider using the car AC when you Running-in period really require. Consider using lower blower speeds rather than higher for The more you look after the engine when NOTE it is new, the more satisfied you will be cooling as at higher blower speeds it Avoid excessive revving up of engine consumes more electric power with its performance in the future. rpm. Do not keep engine at idling for which is ultimately drawn from en- Avoid rapid acceleration and prolonged long duration. gine by burning fuel. high speed running of the engine for the  Avoid unnecessary extra electrical first 1,500 – 1,800 kms. loading on the car.

 Stop the engine wisely at traffic sig- Do not exceed the following road speeds nals. Switch ‘OFF’ the engine at the during running in period. traffic signal only if the stoppage 92 STARTING AND DRIVING Seat Adjustments reclined position as this can be dan- WARNING ! gerous. You could slide under the Front seat adjustments Do not adjust the driver's seat while seat belt in a collision. Following seat adjustments can be car- driving. Adjusting the seat while driv- Seat height adjustment (if equipped) ried out manually. ing could cause the driver to lose con- trol of the vehicle. To raise the seat, pull and continue pumping the lever (2) in the upward di- Seat backrest angle adjustment rection until the seat is at the desired To change the seat back rest angle, lean height. forward slightly and pull up the lever (1). To lower the seat, pump the lever down- Adjust seat backrest until it reaches de- ward until the seat is at desired height. sired comfortable position. Make sure that lever returns to its original position Seat forward / rearward adjustment and seat is securely latched. Lift lever (3) and slide the seat forwards or rearwards. Release lever and make NOTE sure that seat is securely latched.

1. Backrest angle Adjust the seat backrest until your 2. Seat height (if equipped) arms are slightly angled when hold- NOTE ing the steering wheel. 3. Seat forward / rearward adjustment Adjust the driver seat position in such lever a way that the driver will be able to operate the controls pedals comfort- WARNING ! ably. Never travel in a moving vehicle with

the seat backrest in an excessively

93 STARTING AND DRIVING Adjustable head restraint Rear View Mirrors (If equipped) Inside Rear View Mirror (IRVM) To adjust the mirror, set the selector knob to the normal position and then move the mirror up, down or sideways

manually to obtain the best rear view. WARNING ! When driving at night, set the selector Do not drive the vehicle without the tab to select anti-glare mode to reduce seat head restraints. Head restraints glare from the headlights of vehicles be- are intended to help reduce injuries hind you. during an accident.

Adjust the head restraint so that it is as NOTE close to the head as possible and the center of the head restraint supports the Head restraint are not adjustable for back of the head at eye level. This will seats with integrated head restraints. reduce the potential for injury to the head and neck in the event of an acci- Rear seats dent or similar situation. Fixed rear seats are provided. Refer

‘Stowage area’ section for more details.

94 STARTING AND DRIVING Motorized outer rear view mirrors To adjust the mirrors: NOTE (If equipped) 1. Move the selector switch to the left Use antiglare position only when nec- (L) or right (R) to select the mirror you essary, as it reduces rear view clarity. wish to adjust. Outer Rear View Mirrors 2. Press the outer part of the switch that corresponds to the direction in You can adjust the outer rear view mir- which you wish to move the mirror. rors manually with the knob located on the driver’s and front passenger’s door Sun Visors panel. Adjust the outside rear view mir- rors to desired position.

NOTE

Objects visible in mirror are actually The switch to adjust the motorized mir- closer than they appear. Always rors is located on the driver’s door. You make sure of the actual distance can adjust the mirrors when the ignition from the road users traveling be-hind switch is in the “ACC” or “ON” position. by glancing over your shoulder. Auto folding (If equipped) The sun visors can be pulled down to To fold / unfold the ORVMs, keep the Se- block glare coming through the wind- lector switch in center position (i.e. nei- shield. ther ‘L’ nor ‘R, position) and then toggle down.

95 STARTING AND DRIVING To block glare from side windows To adjust the steering wheel WARNING ! Pull down the sun visor and release it 1. Adjust the seat to a comfortable po- from retainer. Swing the sun visor to the sition. Before starting off, make sure the side. steering wheel position is locked. 2. Push release lever completely down Vanity mirror Never unlock or adjust the steering to unlock the steering column. wheel while the vehicle is in motion. Vanity mirror is provided on the back of 3. Adjust the steering wheel to the de- the front passenger side sun visor. sired position. Steering lock cum ignition switch Steering Wheel Adjustment 4. Pull release lever up completely to lock the steering column. 5. Make sure that steering wheel is se- curely locked by checking up and down direction.

NOTE When adjusting the steering wheel, make sure that: You can operate control pedals with-

out any obstacles. You can see all the displays in the in- The ignition switch has the following four You can adjust the steering wheel posi- strument cluster clearly. positions: tion to suit your convenience. LOCK - This is the normal parking posi- The release lever is located under the tion. Key from lock can be removed in steering column. this position only. 96 STARTING AND DRIVING “LOCK” position prevents normal use of Starting the Engine (Manual Trans- WARNING the steering wheel after the key is re- mission) ! moved. Make sure that parking brake is en- The engine emits poisonous exhaust To release the steering lock, insert the gaged and vehicle is in neutral gear. gases such as carbon monoxide. In- key and turn it clockwise to one of the haling these exhaust gases leads to other positions. Depress the clutch pedal fully and crank poisoning. There is a risk of fatal in- the engine. Do not press the accelerator jury. Therefore never leave the en- ACC - Accessories such as the infotain- pedal when starting the engine. gine running in enclosed spaces with- ment system can be operated, but the out sufficient ventilation. engine remains ‘OFF’. Steering gets un- NOTE locked. Starting off The Starter protection system fit-ted ON - This is the normal operating posi- To start off, depress the clutch pedal tion. All electrical systems are ‘ON’. in this vehicle does not allow you to crank the engine until you fully de- fully and shift into 1st gear. START - Turn the key further clockwise press the clutch pedal. After releasing the parking brake, gradu- to the START position, (spring loaded) to ally release the clutch and slowly press start the engine. As soon as the engine Release the key as soon as the engine the accelerator. starts, release the ignition key, which re- starts. Repeat if engine does not start. turns to ON position. While cranking, all NOTE accessories will be momentarily ‘OFF’. NOTE Illuminated Key Ring (if equipped) When shifting or starting off, do not The Starter protection system race the engine. Racing the engine When the vehicle is unlocked, the illumi- switches off the starter when it is can shorten engine life and affect nated key ring glows up. This helps to lo- cranked for more than 10 secs. In smooth shifting. cate ignition switch in the dark. such a case, get the key back to ‘OFF’ position & wait for 30 secs.

97 STARTING AND DRIVING Gear Shifting and Driving (Manual Do not de-press clutch pedal while Drive modes Transmission) driving the vehicle stationary on a ‘ECO’ and ‘CITY’ drive modes are pro- slope. vided for Manual Transmission. These  If clutch pedal lower/upper from modes can be used to adjust engine brake pedal, in this condition cus- characteristics and vehicle performance tomer should contact a Tata Mo- in line with desired requirement. tors authorized service center. Drive mode selection switch is provided Current gear indication on dashboard fascia for activation The Driver Information display (DIS) in the Instrument Cluster indicates the cur- Drive Performance rent gear position engaged. Mode Gear recommendation Optimum engine Torque Up or down arrow will be displayed in ECO and Power output for DIS, recommending whenever gear (for MT) FUEL EFFICIENT perfor- The gearshift pattern is as shown on the mance gear lever knob. Gear shifting should al- should be shifted to up or down. ways be done with clutch pedal pressed. Increased engine Torque NOTE CITY and Power output for BALANCED performance NOTE  Gear recommendation is di played when the clutch pedal is in fully re- SPORT Produce more torque  Depress the clutch fully when gear leased position. (for AMT) from engine. shifting. The reverse gear should  If “F” is displayed in DIS of instru- be engaged only when the vehicle ment cluster it means ‘Fault’ condi- is stationary. Wait for 5 seconds af- tion. Contact a TA-TA MOTORS Au- ter declutching to ensure smooth thorized Service Centre. engagement of the reverse gear. 98 STARTING AND DRIVING Braking occur after the vehicle has been WARNING ! washed. Your vehicle has power assisted brakes. Do not switch off the ignition while The distance needed to bring the vehicle Brake performance may become poor driving. to a halt increases with the speed of the and unpredictable if brakes are wet. If you switch off the ignition while vehicle. Start applying brake anticipating After driving through water or washing driving, safety-relevant functions are the distance and slow down gradually. the underside of the vehicle, test the only available with limitations, or not brakes while driving at a slow speed to at all. This could affect the power WARNING ! see if they have maintained their normal steering and the brake boosting ef- Never use the brake pedal as a foot- effectiveness. If the brakes are less ef- fect. You will require considerably fective than normal, dry them by repeat- rest. more effort to steer and brake. There edly applying the brakes while driving is a risk of an accident. If you rest your foot on the brake pe- slowly until the brakes have regained dal while driving, the braking system their normal effectiveness. can overheat. This in-creases the stopping distance and can even Braking on downhill gradients cause the braking sys-tem to fail. On long and steep gradients, you must There is a risk of an accident. reduce the load on the brakes by shifting Never depress the brake pedal and early to a lower gear. This allows you to the accelerator pedal at the same take advantage of the engine braking ef- time. fect and helps avoid overheating and ex- cessive wear of the brakes. If you have driven for a long time in heavy rain without braking, there may be a delayed reaction from the brakes when braking for the first time. This may also

99 STARTING AND DRIVING Switch-off the engine Automated Manual Transmission WARNING ! Turn the key to ‘ACC’ position to switch (AMT) Gearbox: (if fitted) Do not shift to lower gear on a slip- off the engine. Before switching off the pery road surface in an at-tempt to in- engine, run the engine in idle condition crease the engine's braking effect, for at least 30 seconds and then switch the drive wheels could lose their grip. off. This will allow the engine oil to lubri- There is an increased danger of skid- cate the turbocharger, till its speed is ding and accidents. fully reduced and also allow the unit to cool down.

WARNING ! A quick burst on the accelerator be- fore turning off the engine serves ab- solutely no practical purpose; it wastes fuel and is damaging espe- Gear Shift Lever (AMT) cially to turbocharged engine. The 5-speed Automated Manual Trans- mission (AMT) Gearbox offers a choice of

two driving modes: WARNING ! 1. Automated mode with the gear lever in position ‘A’ Do not switch the engine off when it is running at high speed. This will 2. Manual mode with the gear lever in lead to premature turbocharger bear- position ‘M’. ing wear.

100 STARTING AND DRIVING Starting: NOTE NOTE a. Engage the parking brake firmly. Press Brake pedal. The engine can only be started when If displayed on the Instrument the gearshift lever is in “N” position Cluster display, it means ‘Fault condi- with the brake pedal firmly pressed. tion. Contact a TATA MOTORS Author- ized Service Centre immediately. Driving: a. With the engine running and brake AMT Instruction sticker: pedal pressed, depending on your re- Follow the instructions provided on the quirement shift the lever on R, A or sticker before driving the vehicle. M. Check the position engaged on the Instrument Cluster display. b. Release the parking brake. c. Release the brake pedal then be- cause of creep feature, vehicle will move and if required press accelera- b. Put the ignition 'ON' tor pedal. c. While the brake pedal is pressed, NOTE bring the shifter lever to Neutral - 'N'. Check 'N on instrument cluster. Use right foot only to operate brake d. Crank to start the engine with the or accelerator pedal.

brake pedal still pressed. Do not operate accelerator and brake pedal simultaneously. Do not use your left leg to operate the pedals while driving AMT vehicle.

101 STARTING AND DRIVING Driving Modes Do not shift the lever in “N” position, Automatic Mode: Neutral: even momentarily, when the vehicle is in motion.

Reverse:

Automatic mode will be engaged only when vehicle is stationary and brake pe- Vehicle is in neutral gear position. This dal pressed. An audio signal indicates will be indicated on instrument clus- ter. Reverse gear will be engaged only when when Automatic gear is engaged. vehicle is stationary and brake pedal will be indicated in instrument cluster WARNING ! pressed. An audio signal indicates when Gear Upshift and Downshift will be done reverse gear is engaged. will be indi- automatically while driving. Always make sure to keep the gear cated on instrument cluster. shift lever in the “N” position, when the engine is running and vehicle is stationary.

102 STARTING AND DRIVING Manual Mode: step in the order of 1st  2nd3rd 4th Drive Mode: 5th gear. Two drive modes ‘CITY’ and ‘SPORT’ are provided. These modes can be used Pull the gearshift lever to the ‘–’ direc- to adjust engine characteristics and ve- tion and release it. Every time the lever hicle performance in line with desired re- is operated, downshifting takes place in quirement. CITY mode is the default the order 5th  4th 3rd 2nd 1st mode. To activate SPORT mode, Press gear. ‘S’ button situated on the gear shifter console. NOTE Down shifting of gear occurs auto- matically while braking/engine rpm reduction. Shift gear lever to left for engaging manual mode. An audio signal indicates In manual mode, gears are not shifted when manual mode is engaged. will automatically unless the engine RPM be indicated in instrument cluster. threshold is reached. In manual mode, driver should select the desired gear by shifting lever to, + Upshift the gears.

- Downshift the gears. ‘SPORT’ mode activation will be dis- Push the gearshift lever to the ‘+’ direc- played on instrument cluster. It can be tion and release it. Every time the lever activated only in automatic mode. is operated, upshifting takes place 1 To deactivate press the ‘S’ button again.

103 STARTING AND DRIVING Stopping: idle condition for at least 30 seconds NOTE and then switch off. The vehicle can be stopped by depress- ing the brake pedal regardless of the Exhaust fan in the engine compart- gear position. This is because the clutch ment will remain 'ON' for a short while WARNING ! after IGN is switched 'OFF'. is automatically disengaged to prevent Do not switch the engine off when it the engine from stalling. Parking: is running at high speed. If the gearshift lever is in the ‘A’ posi- AMT does not have a parking position. tion, the gear will be downshifted to ‘1st’ Creeping feature: The vehicle can be parked with the gear- when the vehicle stops. Also, if the gear- shift lever in any position. Creeping function allows the car move- shift lever is in the ‘M’ position, the gear ment without accelerator Pedal pressed 1. Apply the parking brake firmly. will be downshifted to ‘1st’ when the ve- when the brake pedal is released. hicle stops. 2. Depress the brake pedal and shift the gearshift lever to the ‘R’ position This functionality is generally used in NOTE on a downhill slope, or to the drive parking maneuvers, with 1st or ‘R’ gear ‘A’ mode or the ‘M’ position in the engaged, in this situations the driver en- ‘CITY’ mode will give optimum en- manual ‘M’ mode on an uphill slope ters and exits from creeping just by gine Torque and Power output. Drive or flat road and confirm the gear po- pressing the Acc. pedal. the vehicle in ‘CITY’ mode to get max sition by checking the gear position  Creep feature is enabled for Manual fuel economy. If in case of AC discom- indicator on instrument cluster. Gear fort switch to ‘SPORT’ mode. as well as Auto Mode for first and engagement (R or A) can be done reverse gear. with ignition ON/engine running con-  After vehicle cranking and brake pe- dition only. dal released vehicle starts moving 3. Turn the key to ‘ACC’ position to without pressing accelerator Pedal. switch off the engine. Before switch-

ing off the engine, run the engine in

104 STARTING AND DRIVING  Whenever accelerator pedal is Driving in Adverse condition Driving on a Rainy Day: pressed creep function will be disa- Check brakes, steering, windows, and bled. Driving Through Water: tyres for wear and tyre pressure. Check  Whenever driver door is opened and Never venture to drive through water wiper blades for proper functioning. / or parking brake is engaged, creep when it flows over the guard stones on a Avoid harsh braking and sharp turns. It function will be disabled. bridge. may cause loss of control and lead to a Kick down feature: Your car’s engine may get seriously dam- skid. For slowing down, shift to lower aged if attempted to cross through deep In Automatic mode, while driving at a gears and brake gently. Keep lights ON if water. If at all the situation demands constant speed if the accelerator pedal visibility is poor. that you have to drive through water is quickly pressed the AMT downshifts then; Night Driving: the gear (if required). It ensures opti- Keep engine in fast idling and crawl mum acceleration to complete overtak-  Use head lamp main/dip beam to alert the car in low gear. ing in minimal time. other road users on turns/ cross roads  After driving through water, apply etc. brakes several times to dry the liners Use side indicators for lane change or and to regain original braking. turning.  Do not attempt to start the engine if Switch on hazard warning switch in case car gets flooded with water. of hazardous parking or if your vehicle is  Tow the car to a safe place. disabled to warn the passing traffic.  Take the car to nearest TATA MO- Maintain a speed such that you can stop TORS Authorised Service Centre to within illuminated distance of head check entry of water in cylinders. lamps.  If water has entered the engine, or transaxle or AMT kit, the lubricants will have to be replaced. Get the starter and alternator checked.

105 STARTING AND DRIVING Climbing Sharp Gradients on Loose slippage, possibly resulting in toppling On climbing sharp gradients, never hold Surfaces (MT) over. If unavoidable, choose as mild an the vehicle at a stop using only the ac- angle as possible and keep the vehicle celerator pedal or the creeping function. Apply the parking brake firmly so that the moving. If you perform this operation for a certain vehicle does not roll backwards. If the vehicle stalls or losses headway period of time, this can also cause ex- Shift the gearshift lever to the “M” posi- while climbing a steep hill, make a quick cessive damage to the clutch. tion while depressing the brake pedal. shift to reverse and allow the vehicle to Descending Sharp Gradients (MT) Select suitable gear position. move back with the control of engine compression. Depending on the severity of the gradi- Release the brake pedal and depress ent, shift into appropriate gear. Use en- Climbing Sharp Gradients using the accelerator pedal gradually, and gine braking judiciously without over rev- AMT: when the vehicle starts to move, release ving the engine. the parking brake and depress the accel- Apply the parking brake firmly so that the Brake application under such situations erator pedal to start off. vehicle does not roll backwards. should be done very smoothly to avoid Choose as smooth a slope as possible Shift the gearshift lever to the “A” posi- loss of control. Select appropriate gear and select the appropriate gear so that tion while depressing the brake pedal. so that gear changing or clutch disen- gear changing in the middle of the climb Make sure that the gear position indica- gagement is not involved while descend- is not required. tor in the instrument cluster displays ing the gradient. Changing gears in the middle of the ‘1st’ gear. climb can cause loss of momentum and Release the brake pedal and depress NOTE engine stalling. Shifting to lower gear the accelerator pedal gradually, and Creeping function will not operate has to be done cautiously to avoid loss when the vehicle starts to move, release when vehicle is in standstill condition of traction. the parking brake and depress the accel- on inclined surface. Under no conditions should the vehicle erator pedal to start off. be moved diagonally across a hill. The danger is in loss of traction and sideways 106 STARTING AND DRIVING Descending Sharp Gradients using WARNING ! AMT: Try not to hold the brake pedal down Depress the brake pedal and shift the too long or too often while going gear shift lever to the ‘A’ position. Make down a steep or long hill. sure that the gear position indicator in This could cause the brakes to over- the instrumental cluster displays ‘1st’ heat, resulting in reduced braking ef- gear. ficiency. Failure to take this precau- Release the brake pedal and depress the accelerator pedal slowly. Even if the tion could result in loss of vehicle accelerator pedal is not depressed, the control. clutch will be engaged when the vehicle Parking brake applied speed increases. To apply the parking brake, pull the lever up fully (1). The parking brakes tell-tale WARNING Using Engine Braking ! illuminates on the instrument cluster. When descending on sharp gradi- When driving on the downhill slope, ents, NEVER turn the ignition key to down shifting is recommended. So you the ‘OFF’ position. Emission control can use engine braking. system damage may result. By placing the gearshift lever in “M” po- sition, the manual (M) mode is selected, and you can shift to a lower gear manu- ally. Parking Brake Mechanical parking brake acting only on the rear wheels is provided on the vehi- cle. Parking brake released 107 STARTING AND DRIVING To release it, pull the lever up slightly (1), Reverse Park Assist (if equipped) press the release button (2) and push NOTE the lever down (3). Parking brakes tell- Reverse Park Assist system is an elec- tale on the instrument cluster will turn  When parking on a downhill gradi- tronic parking aid that will assist you to ‘OFF’ when the lever is fully released. ent, place the gear lever in park your vehicle safely when in reverse ‘Reverse’ position. While parking gear mode. It provides audio and visual information through the vehicles info- NOTE on uphill gradient, place the gear lever in the ‘1st’ position. tainment system. Apply the parking brake properly be-  Do not use parking brake for brak- Always look at surrounding before initiat- fore leaving the vehicle and release it ing unless unavoidable circum- ing reverse parking, for kids, pets and el- before moving. stances like when service brake is derly people moving around the vehicle. not working properly. The braking Vehicle parking distance is considerably longer Park the vehicle in a safe place. Switch and the wheels could lock. There on the indicator signal before turning to is an increased danger of skidding park. and accidents.

 Apply the parking brake.  Ensure that all window glasses are closed and all lamps are turned WARNING ! ‘OFF’. Never leave children unsupervised in  At night, put on the parking lights if the parked vehicle. They could also required. operate the vehicle's equipment.  Remove the key from the ignition There is a risk of an accident and in- There are 4/3 ultrasonic sensors placed switch and lock the vehicle. jury. on the rear bumper of the vehicle. Once  Block the wheel if parked on a slope. the system is activated, the sensors will 108 STARTING AND DRIVING detect the proximity of an obstacle from  If object is mesh fence made up of the bumper, and this information would thin wires, where echoes can’t be be displayed on the vehicles infotain- given by the surface. ment system. In Low variants, only audio warning shall be given through a buzzer.  Fast moving objects passes in the sensor field of detection, where ech- oes are not processed by the system. WARNING !  If object is made/covered by foam or 0 to 25 cm obstacle detection perfor- sponge or snow where ultrasonic mance is not guaranteed due to ultra- sound signals are absorbed. sonic sensor technology limitation.  Objects close to the rear bumper can Park assist indications go undetected by the Reverse Park Reverse park assist limitations In case of Reverse park assist system Assist field of detection. Driver malfunctions, the following screen may Reverse Park Assist system is not a colli- should use extreme caution while parking the vehicle. appear on the infotainment system. sion avoiding system. It is solely the driver’s responsibility to park the vehicle Reason for this fault may be  If height of the bumper is changed safely. due to alteration to the suspension or a. Park Assist Controller / Body Control other causes Reverse Park Assist feature works on ul- Module Failure" tra sound echo technology, due to which  If the sensor areas are extremely hot b. Sensor Malfunction performance is not guaranteed in follow- from direct sunlight or cold due to c. Partner components such as Info- ing scenarios: freezing weather. tainment music system, Instrument  If Sensors are covered by a hand, Cluster failure.  If the object has a sharp edge sur- face, where surface may divert ech- sticker, accessory, etc. oes from sensor reception.

109 STARTING AND DRIVING  If ultrasonic noise is present around Reverse park assist system preven- Vehicle due to other vehicle sensors, tive maintenance horn, engine, air braking system 1. Regularly clean the Sensors and (large vehicles), Exhaust Fans, Wire- keep them free from dust, ice, mud, less transmitters or mobile phones water, chewing gum etc. for proper  If the vehicle speed exceeds 10 working of the system. Use a smooth km/h, the system will not warn you cloth for cleaning. even though objects are detected, er- 2. Do not use water at high pressure for ror message 'Vehicle Speed is high, drive slowly!' will appear. cleaning the sensor. Activation  Driving on uneven road surfaces e.g. 3. Do not cover the Sensors. This will in- Gravel, unpaved roads, Artificial terrupt park assist performance.  Reverse gear Speed Breakers, or gradient. This System will activate, if reverse gear Rear View Camera is engaged, or park assist button (if WARNING ! Rear View Camera is a visual reverse equipped) is pressed. Due to any reason, if the sensor gets guiding system. When reversing or park- misaligned or loses its intended fit- ing, make sure that there are no per- ment position, contact your dealer for sons, animals or objects in the area in refitment. which you are reversing.

NOTE NOTE Turning the ignition ‘OFF’ ‘while the Turning the ignition ‘OFF’ ‘while the Park assist feature in running would Park assist feature in running would disable the feature. disable the feature. 110 STARTING AND DRIVING Deactivation Red Line Cleaning camera 1. Due to environmental reasons, dust, System will deactivate, if reverse gear is Indicates, if rear objects are in this col- ored zone, you have to stop the vehi- mud or fog may accumulate on the disengaged, or park assist button (if camera lens. So regularly clean the equipped) is pressed cle and not allowed to go backward. If you still go backward, your vehicle will camera lens. Understanding Guidelines Indica- hit the object 2. Use water to clean the camera lens. tion Do’s and don’t Do not use extreme cold or hot water.  Do not use camera when tailgate is Rapid changes in temperature may open. If tailgate is open, visual in- brittle the camera lens. Do not apply formation may not be the actual High Pressure water for cleaning. rear view of the vehicle & system 3. Wipe the camera lens with soft cloth. will warn with message 'Tail Gate 4. Do not use hard cloth or material to Open, Please close. wipe the camera lens. This will cause  When the camera is operated un- scratches on the camera, and leads der fluorescent lights, sodium light to deteriorated visual image on the Green Line or mercury light etc., illuminated ar- display. Indicates, if rear object is in this colored eas on the lens may appear to 5. Do not apply organic solvent, car zone, you have to be cautious. Still you flicker in the display. wax, window cleaner or glass coat to can go backward safely.  Do not attach any advertisement or clean the camera. If this is applied, styling or any kind of stickers on top wipe it off as soon as possible. Yellow Line of camera. If this happens, camera 6. Do not apply heavy force on lens, Indicates, if rear objects are in this col- cannot provide you the visual im- while cleaning. ored zone, you have to take utmost age and may damage camera. 7. Do not remove mud, snow on the care. However, objects fall in this  Do not add any accessory, which camera lens using stick or hard ma- zone, may not hit vehicle will obstruct camera field of view. terial. Use normal water and soft cloth.

111 STARTING AND DRIVING sure that, camera is fitted less variation in ambient temper- WARNING ! properly at the intended location. ature.  The camera uses fish eye lens. So  In case of uneven road conditions  The area displayed by the rear the size of the objects or in the or up-hill or downhill conditions, view camera is limited. The cam- display may differ from the actual do not depend on rear view cam- era does not display objects that size and distances In low light era park aid. are close to or below the bumper, conditions, the screen may  Do not apply any kind of force on underneath the vehicle, or ob- darken or image may appear the camera. jects out of the camera’s field of faint. view. The area displayed on the  Always use rear View mirrors  If the tire sizes are changed, the along with Rear View Camera for screen may vary according to ve- position of the fixed guidelines confirming the safety of the rear hicle orientation or road condi- displayed on the screen may and the surrounding conditions. tions. change.  High humidity and variation in  During rainy conditions, image ambient temperature may result may get obscured. In such condi- into condensation inside the tions, do not depend on camera camera lens, which may further view. The camera used in the ve- result into degradation of camera hicle, may not reproduce the video feed on the screen. It is rec- same color of the real object. ommended that not to rely on  In case of damage of the rear por- camera video feed for parking as- tion of the vehicle, camera posi- sistance in such scenario. This tion may change. Which causes phenomenon is temporary and wrong visual information on dis- will be automatically recovered play. In case of damage, make with reduction in humidity and

112 STARTING AND DRIVING Rear view camera system precau-  The area displayed on the screen tions may vary according to vehicle orien- 1. Area displayed on screen tation conditions. The rear view camera system displays an  Objects, which are close to either cor- image of the view from the bumper of ner of the bumper or under the the rear area of the vehicle. To adjust the bumper, cannot be seen on the image on the rear view monitor system screen. screen.  The camera uses a special lens. The distance of the image that appears on the screen differs from the actual distance. The monitor may not dis- The distance guidelines will appear to be play items that are located higher closer to the vehicle than the actual dis- than the camera field of view. tance. 2. When the ground behind the ve- Because of this, objects will appear to be hicle slopes up sharply farther away than they actually are. In the same way, there will be a margin of error between the guidelines and the actual distance/course on the road.

113 STARTING AND DRIVING 3. When the ground behind the ve- The distance guidelines will appear to be the screen and the actual dis- hicle slopes down sharply further from the vehicle than the actual tance/course on the road. distance. 5. When approaching three-dimen- Because of this, objects will appear to be sional objects closer than they actually are. In the same way, there will be a margin of error The distance guidelines are displayed between the guidelines and the actual according to flat surfaced objects (such distance/course on the road. as the road). It is not possible to deter- mine the position of three-dimensional 4. When any part of the vehicle objects (such as vehicles) using the dis- sags tance guidelines. When approaching a three-dimensional object

a. Distance guidelines

When any part of the vehicle sags due to the number of passengers or the distri- bution of the load, there is a margin of

error between the fixed guide lines on 114 STARTING AND DRIVING b. Vehicle width guidelines Visually check the surroundings and the area behind the vehicle. In the case shown below, the truck appears to be outside of the vehicle width guidelines and the vehicle does not look as if it hits the truck. However, the rear body of the truck may actually cross over the vehicle width guidelines. In reality if you back up as guided by the vehicle width guide- lines, the vehicle may hit the truck.

Visually check the surroundings and the area behind the vehicle. On the screen, it appears that a truck is parked at point B. However, in reality if you back up to point A, you will hit the truck. On the screen, it appears that A is closest and C is furthest away. However, in reality, the distance to A and C is the same, and B is farther than A and C.

115 STARTING AND DRIVING

116 EMERGENCY AND BREAKDOWN ASSISTANCE Emergency Equipment Tool kit and tow hook Jack You should be familiar with the location of the emergency equipment provided in the vehicle and how to use it. Check this equipment periodically and ensure that they are in proper working condition and stowed at their locations. First aid kit The first aid kit is kept inside the glove box compartment.

The kit contains items that can be used in case of minor injuries only. Tool kit & tow hook are kept inside lug- A scissors jack is kept inside luggage gage compartment near spare wheel. compartment near the spare wheel. NOTE NOTE NOTE Check contents of the first aid kit pe- riodically and replenish consumed or The tool kit should be properly stored The jack should be used only to expired items. when not in use. change wheels. It is important to read the jacking instructions in this section before attempting to use the jack.

117 EMERGENCY AND BREAKDOWN ASSISTANCE Advance warning triangle Hazard Warning Switch An advance warning triangle is kept in the luggage compartment. Use advance warning triangle to warn the approaching traffic in case of vehicle break-down or during emergency, where your vehicle could become a potential traffic hazard. Press hazard warning switch, all turn sig- nal lamps will start blinking

Keep the warning triangle at suitable dis- NOTE tance (depending on the situation) be- Press the hazard warning switch to acti- hind your vehicle in the same lane of After using the warning triangle, tie it vate the hazard warning. All the turn sig- traffic. The reflecting side of the triangle firmly and keep it inside the bag to nal lamps will flash simultaneously. To should face the oncoming traffic and it avoid rattling noise. turn OFF, press the switch again. should be free from any obstacles. Use the hazard warning to warn the traf- Remove the advance warning triangle fic during emergency parking or when carefully from the bag and assemble. Re- your vehicle could otherwise become a fer instructions given on the bag. traffic hazard. The hazard warning lamps can operate even if the ignition is switched off.

118 EMERGENCY AND BREAKDOWN ASSISTANCE In Case of Flat Tyre Spare Wheel WARNING !  Reduce vehicle speed gradually, If you drive with a flat tyre, there is a without making any sudden steering risk of the following hazards: or braking maneuvers. Pay attention to the traffic conditions as you do so.  A flat tyre affects the ability to  Switch on the hazard warning lamps. steer or brake the vehicle.  You could lose control of the vehi-  Stop the vehicle on solid, non-slip- cle. pery and level ground, as far away as  Continued driving with a flat tyre possible from traffic. will permanently damage the tyre  If possible, bring the front wheels into and cause excessive heat the straight-ahead position. buildup and possibly a fire. There  Secure the vehicle against rolling is a risk of an accident. away. Spare wheel is located in the luggage  Set the parking brake firmly and shift compartment. into “R” (Reverse) gear.  Switch off the engine. To access the spare wheel, open the  Keep advance warning triangle at a trunk lid, lift the carpet up and fold it. suitable distance behind the vehicle To remove the spare wheel, unscrew and as an indication of breakdown. remove the retaining bolt. Take out the  Clear all passengers and luggage spare wheel. from the vehicle.  Close all the doors.

119 EMERGENCY AND BREAKDOWN ASSISTANCE Following precautions are to be  Snow chains cannot be used on taken when temporary spare wheel the temporary spare wheel. NOTE is fitted on the vehicle. Your vehicle may exhibit some unu- sual driving characteristics when fit- WARNING ! ted with temporary spare wheel. WARNING !  Drive the shortest possible dis- tances. The temporary spare  Never use more than one tempo- wheel should be exchanged for a rary spare wheel. normal wheel as soon as possible.  Do not drive through an automatic The temporary spare wheel is de- car wash. signed for a short period of use  Never use a temporary spare tyre only. if it is damaged or worn down to  “80 km/h” or “50 mph” is the max- the tread wear indicators. imum speed you are permitted to  The ground clearance of your ve- drive with this tyre. hicle may be reduced. Take care Never drive faster than 80 km/h when parking next to curb. (50 mph). Do not accelerate  The temporary spare should not quickly, brake suddenly or drive at be installed on the front axle if the high speed through bends. vehicle must be driven in snow or  After fitting the temporary spare on ice. wheel, the tyre pressure must be  Do not tow whilst the temporary checked as soon as possible. spare wheel is installed.  Recommended tyre pressure is 36 psi (2.5 bar) for temporary spare wheel.

120 EMERGENCY AND BREAKDOWN ASSISTANCE Wheel covers (if equipped) Jacking point location on vehicle NOTE Use the respective jacking points for Do not use any sharp tools (such as jacking up the vehicle. Jacking point lo- screw driver etc.) to remove the cation are shown below: wheel cover.

Changing flat tyre Loosen the nuts of the flat tyre in diago- nal sequence as indicated in figure. Do not remove the nuts completely before jacking the vehicle.

Insert a piece of cloth between the spokes of the wheel cover and pull it out- wards. Take out detached wheel cover from the wheel rim. Jacking point location When installing the cover, make sure that it is positioned so that it does not cover the air filling valve. Apply equal pressure at the circumference of the wheel cover to fix it in the wheel rim.

Wheel nut removal

121 EMERGENCY AND BREAKDOWN ASSISTANCE Jacking the vehicle Position the jack vertically and align the “U” slot provided on jack with jacking point as shown below.

Rear jacking Location Assemble the Jack handle and wheel spanner (as shown in jacking fig.) Raise it by turning the jack handle clock- wise until the jack sits completely on jacking point and the base of the jack Front jacking Location lies evenly on the ground.

122 EMERGENCY AND BREAKDOWN ASSISTANCE Remove wheel mounting nuts with the Place the flat tyre at spare wheel loca- help of wheel spanner and take out flat tion. tyre. NOTE NOTE Check and correct the tyre pressure Do not place wheel nuts in sand or on and wheel nuts tightness of the a dirty surface. Do not apply oil or changed wheel at nearest authorised grease on it. service station. Get the flat tyre repaired at the earli- Roll the spare wheel into position and est. align the holes in the wheel studs.

Jacking Install wheel nuts with their cone shaped end facing the wheel. Tighten each nut NOTE WARNING by hand until the wheel is securely !  The jack is designed only to raise seated on the hub. If you do not position the jack cor- and hold the vehicle for a short rectly at the appropriate jacking point Lower the jack completely then tightens time while a wheel is being of the vehicle, the jack could tip over the wheel nuts one by one using wheel changed. It is not suited for per- with the vehicle raised. There is a risk spanner. forming maintenance work under the vehicle. of injury. Press fit the wheel cover back (if  Use the jack on level, hard Continue to raise the jack slowly and equipped). ground. Avoid changing the smoothly until the tyre clears the ground. Restore all the tools and jack at their wheel on uphill and downhill Do not raise the vehicle more than nec- respective location. slopes. Apply wheel chokes if ve- essary. hicle is parked on slope.

123 EMERGENCY AND BREAKDOWN ASSISTANCE  Before raising the vehicle, secure parking brake firmly and keep the gear-  Make the final connection (other end it from rolling away by applying shift lever in neutral. Turn off all vehicle of the negative terminal) to an un- the parking brake. accessories, except those necessary for painted, heavy metal part (i.e. engine  Do not use wooden blocks or sim- safety like hazard warning lamps. mounting stud/nut) of the vehicle of ilar objects as a jack underlay. Make jump lead connections as follows: discharged battery.  Never place your hands and feet  Start the engine of the vehicle with or lie under the raised vehicle the discharged battery. when it is supported by the jack.  Before disconnecting the jumper ca-  Never run the engine when the bles, let the engine run for several vehicle is supported by the jack minutes. and never allow passengers to re-  If the booster battery you are using is main in the vehicle. fitted to another vehicle, start the en-  Never open or close a door or the gine of the vehicle with the booster trunk lid when the vehicle is battery. Run the engine at moderate raised. speed. Jump Lead Starting  Remove the jump leads in the exact reverse order in which you connected Use only a battery of same rating & ca-  Connect one end of the first jump them. pacity to jump start your vehicle. Position lead to the positive (+) terminal of the the booster battery close to your vehicle discharged battery. NOTE so that the jump leads will reach both  Connect the other end to the positive batteries. Do not disconnect the discharged (+) terminal of the booster battery. battery from the vehicle. When using a battery of another vehicle,  Connect one end of the second jump do not let the vehicles touch. Apply the lead to the negative (–) terminal of the booster battery. 124 EMERGENCY AND BREAKDOWN ASSISTANCE fire, open flames, creating sparks Towing WARNING ! and smoking. Ensure there is suf- When towing a break down vehicle, cer- ficient ventilation while charging Never connect the jump lead directly tain precautions and procedures must and jump-starting. Do not lean to the negative (–) terminal of the dis- be taken to prevent damage to the vehi- over the battery. charged battery. This may lead to an cle and/or components. Failure to use  Make sure that the positive termi- explosion. standard towing precautionary nal of a connected battery does measures when lifting or towing a break not come into con-tact with vehi- down vehicle could result in an unsafe WARNING ! cle parts. Never place metal ob- operating condition.  Do not allow battery electrolyte to jects or tools on a battery. come in contact with eyes, skin,  It is important that you observe To ensure proper towing and to prevent fabrics or painted surfaces. The the described order of the bat- accidental damage to your vehicle, take fluid contains acid which can trey terminals when connecting help of a TATA MOTORS authorized cause injury and severe damage. and disconnecting a battery. If dealer or a commercial tow-truck ser- Wear protective apparel. Do not you are in doubt, seek assistance vice. inhale any battery gases. Keep from qualified specialist work- children away from batteries. In shop. NOTE case if battery acid comes in con-  Never connect or disconnect the tact with the skin, wash it off im- battery terminals while the en- Make sure that the parking brake is released; vehicle in neutral gear po- mediately with water and seek gine is running. sition and steering wheel is unlocked. medical attention. The power steering functions only  During charging and jump-start- when engine is running. Hence, dur- ing, explosive gases can escape ing towing the steering efforts will be from the battery. There is a risk of more an explosion. Particularly avoid

125 EMERGENCY AND BREAKDOWN ASSISTANCE Tow hook fitment In case of break down we recommend WARNING ! that your vehicle be towed with the driv-  Open the trunk lid and remove tow ing wheels off the ground or place the ve-  Never get under your vehicle after hook from the tool kit. it has been lifted by a tow truck. hicle on a flatbed truck as shown.  Open the tow hook cover provided on  For towing a vehicle, the best way the front bumper by pressing it at the is to use a wrecker. Alternatively WARNING bottom part and simultaneously pull- ! use a rigid tow bar. ing it at the top (as shown in fig).  Never tow your vehicle with the  Switch 'ON' the hazard warning in- Screw in and tighten the tow hook in front wheels on the ground or dicators of both the vehicles to clockwise direction. four wheels on the ground (for- warn other road users.  After towing, remove the towing hook ward or backward), as this may  Limit the speed to 20-30 kmph. and press fit the cover properly. cause serious damage to the  In case of brake failure, use the transmission. parking brake to control the vehi-  Place the towing hook in the vehicle  When towing with the rear wheels cle. tool kit. on the ground or on towing dol-  Fasten the tow rope or tow bar at Recommended towing lies, place the ignition switch in the towing eyes. Otherwise, the the ‘ACC’ or ‘ON’ position, and se- vehicle could be damaged. cure the steering wheel in the  When towing, pull away slowly straight-ahead position with a and smoothly. If the tractive rope or similar device. power is too high, the vehicles could be damaged.

126 EMERGENCY AND BREAKDOWN ASSISTANCE B) Where vehicle cannot be shifted in NOTE neutral condition: After shifting the AMT gearshift lever  Secure the rear wheels on a towing to the “N” position, always check the lift and the front wheels on the towing gear position indicator in the instru- trolley. ment cluster shows the “N” position  Apply the parking brake. to make sure that the transaxle is dis- engaged. WARNING !

If the transaxle cannot be put in neutral, A safety chain/belt for tightening the turn the key from the “OFF” to the “ON” wheels with lift should always be position, and move the AMT gearshift used when you tow your vehicle. lever from “N” to “A”, “M” or “R”, then back to “N” again. Then turn the key from the “ON” to the “OFF” position. These procedures may help to put the transaxle in neutral. Towing instructions (AMT): If the transaxle still cannot be put in neu- A) Where vehicle can be shifted in tral, you cannot tow the vehicle without neutral condition: lifting vehicle from rear side.  Shift the gear lever into neutral. NOTE Turn the ignition key to the “ACC” po-  Always unlock the steering wheel be- sition to unlock the steering wheel. fore towing.  Release the parking brake. 127 EMERGENCY AND BREAKDOWN ASSISTANCE Fuses Checking and replacing fuses  Remove the blown fuse by “fuse puller”. The fuse puller and spare Your vehicle has fuse boxes at three lo- If any electrical unit in your vehicle is not fuses are provided in the engine cations. functioning, check the fuses first. compartment fuse box. The vehicles electrical circuits have Please follow the steps below that will fuses to protect the wiring from short cir- guide you to check and replace them. cuits or sustained overload.  Apply parking brake  Switch off all electrical consumers.  Turn the ignition key to the 'LOCK' po- sition.  In the fuse box, identify the defective fuse from its melted wire.

Engine compartment fuse box

 Blown fuses must be replaced with 1. Battery Mounted Fuse Box. fuses of same rating, which you can recognize by color and value. 2. Engine Compartment Fuse Box. 3. Cabin Compartment Fuse Box.

128 EMERGENCY AND BREAKDOWN ASSISTANCE

Battery mounted fuse box Fuse Fuse NOTE Function No. Rating Always ensure that the spare fuses STARTER are replenished. PF1 CAL 1 MOTOR

 Ensure that all other fuses are pressed firmly in position.  If a newly inserted fuse also blows, WARNING ! have the cause traced and rectified at nearest TATA MOTORS Authorized If Fuse box cover is removed for any Service Centre immediately. reason, it should be refitted properly at its original position.

WARNING !

If you manipulate or bridge a faulty fuse or if you replace it with a fuse with higher amperage, the electric ca- bles could be overload-ed. This could result in a fire. There is a risk of an accident and injury. Always replace faulty fuses with the specified new fuses having the cor- rect amperage.

129 EMERGENCY AND BREAKDOWN ASSISTANCE Engine compartment fuse box Fuses - Engine Compartment Fuse Fuse Function No. Rating INTERIOR F/B 2 1 60A IGNITION 2 ABS 40A GLOW PLUG 3 60A (DIESEL) COOLING FAN 4 40A HIGH SPEED 5 EPAS 60A 6 - - INTERIOR F/B 1 7 60A NOTE BATTERY UNDER BON- 8 60A The fuse box layout is for reference NET F/R BOX purpose only. Please refer the sticker 9 - - provided inside the fuse box cover. 10 IGNITION LOAD 60A 11 - - 12 COMPRESSOR 10A STARTER 13 20A SOLENOID 14 ABS ECU 25A

130 EMERGENCY AND BREAKDOWN ASSISTANCE

15 - - INJECTORS Cabin compartment fuse box 40 10A HORN HIGH / (PETROL) Cover removal procedure 16 15A LOW TONE 41 H/L LOW LH 10A Fuse box is located inside the cover be- 17 FRONT FOG 10A HEAD LAMP 42 10A low steering column. To access the fuse 18 EMS BATTERY 10A LOW RH box, remove cover as per procedure AMT HYD PUMP 43 EMS IGN 10A given below. 19 30A (If fitted) 44 - - 1. Fuse box cover is mounted on dash 20 FUEL PUMP 20A 45 H/L LOW LH 10A board with the help of lugs at the top 21 BRAKE LAMP 10A HEAD LAMP 46 10A and bottom of the cover from inside. 22 RELAY COIL 5A LOW 23 - - FRONT WIPER 24 20A MOTOR 25 ABS 5A WASHER 26 10A MOTOR 27 - - REVERSE & 28 10A BRAKE LAMP 29 REAR WIPER 10A 38 EMS ECU 20A EMS ECU 39 15A 131 EMERGENCY AND BREAKDOWN ASSISTANCE 2. To remove the cover, gently pull the cover from bottom side such that the

lugs get disengaged.

Re-fitment procedure

Align and engage the top and bottom mounting lugs with respective slots on dash board and press the cover firmly.

Fuses

Cabin compartment fuse box

132 EMERGENCY AND BREAKDOWN ASSISTANCE

Fuses - Cabin Compartment CDL / ACCES- 14 15A SORY CONN.1 Fuse Fuse Function POWER No. Rating 15 15A SOCKET RESTRAINT RE- 1 10A 16 RELAY COILS 5A LAY TRUNK LID 2 ACC CON.2 15A 17 10A LATCH TRANSIT/ INFO- 3 15A 18 HVAC 10A TAINMENT HEATED REAR 4 BCM 15A 19 SCREEN / 25A/10A INT LAMP/ REV 5 5A/15A FLASHER LAMP & BRK SW MODULE KL.15 MIRROR AD- 20 10A 6 5A I/P JUST MOTOR POWER POS/PARK 7 5A/15A 21 SOCKET CON- 15A LAMP RH/BCM SOLE 8 CLUSTER / OBD 10A TRANSIT/INFO- 22 15A BCM/POSITION TAINMENT 9 5A/15A LH

10 KEY IN 5A IMMOBILIZER / 11 5A EPAS 12 ACC FUSE 5A

BLOWER MO- 13 30A TOR

133 EMERGENCY AND BREAKDOWN ASSISTANCE Bulb Specification

Sr. No. Description Rating Type Qty.

1 HIGH BEAM+LOW BEAM (Option I) 12V, 55W H4 2 HIGH BEAM (Option II) 12V, 55W H1 2 2 LOW BEAM (Option II) 12V,55W H11 2 3 TURN SIGNAL FRONT 12V, W21W W21W 2 4 FOG LAMP FRONT 12V, 19W H16 2 5 STOP + POSITION LAMP REAR 12V LED 2 6 POSITION LAMP FRONT 12V, 5W W5W 2 7 TURN SIGNAL REAR 12V, PY21W PY21W 2 8 REVERSE LAMP 12V, P21W P21W 1 9 REAR REGISTRATION PLATE LAMP 12V LED 2 10 SIDE REPEATER LAMP 12V, WY5W WY5W 2 11 ROOF LAMP 12V LED 1 12 HIGH MOUNTED STOP LAMP 12V LED 1 13 LOAD AREA LAMP 12V, W5W W5W 1 14 TURN SIGNAL FRONT 12V, 21W PY21W 2 15 POSITION LAMP REAR BSO 12V LED 2 16 POSITION LAMP REAR TRUNK LID 12V LED 2 17 REAR FOG LAMP 12V, P21W P21W 1

134 EMERGENCY AND BREAKDOWN ASSISTANCE Bulb Replacement: Replacing - High / Low beam bulb 3. To free the headlamp bulb from the socket, press and swing the retaining (Option I) 1. Remove the rubber press fit cover by simply pulling it off. spring and pull it straight back. Open the bonnet to access the head- lamps.

2. Press the pin and pull the connector 4. Pull out the bulb from the socket. from the bulb.

WARNING ! The engine should not be running when changing bulbs. If the engine has been running just prior to replacing bulbs in the headlight housing, please keep in mind that components in the en- gine compartment will be hot.

135 EMERGENCY AND BREAKDOWN ASSISTANCE 5. Insert the new bulb (without touch- Replacing the position bulb ing the glass) into the socket. Unlock the position bulb by turning the 6. Move the retaining spring up and socket in counter clockwise direction. push it slightly until it locks properly. 7. Refit the connector into the bulb and press the rubber cover on headlamp housing to fit it properly.

WARNING ! It is dangerous if a halogen bulb breaks. These bulbs contain pressur- Replace with the new bulb (refer bulb ized gas and if broken, will explode specification table) and refit it by press- causing serious injury by the flying ing and turning it in clockwise direction glass. Halogen bulbs can break if the firmly into the socket. glass portion is touched with bare Replace with the new bulb (refer bulb hands, body oil could cause the bulb specification table) and refit it by press- to heat unevenly and explode when ing and turning in clockwise direction lit. Never touch the glass portion of the bulb with your bare hands and al- firmly into the socket. ways wear eye protection when han- Replacing the turn indicator dling or working around halogen bulbs. Always keep halogen bulbs out Unlock the turn indicator bulb by turning of the reach of children. the socket in counterclockwise direction.

136 EMERGENCY AND BREAKDOWN ASSISTANCE Option II 3. Disconnect lamp connection. 5. Remove low beam bulb. 1. Open the bonnet to access the head- lamps. 2. Remove the socket cover on the backside of the headlamp.

4. Unlock low beam bulb holder clip, 6. Refit low beam bulb by locking by pushing it backward. high beam bulb holder clip.

137 EMERGENCY AND BREAKDOWN ASSISTANCE 7. Connect the connectors of low 9. Unlock position high beam bulb 10. Remove position high beam bulb beam and refit low beam lamp from its place cover. 8. Disconnect motor connection (if required) & high beam lamp con- nection.

11. Refit position high beam bulb.

138 EMERGENCY AND BREAKDOWN ASSISTANCE 12. Unlock positon bulb from its place. 16. Refit front direction indicator bulb by looking it in clockwise direction.

15. Unlock side indicator lock in anti- 13. Remove position bulb. clockwise direction & remove front direction indicator bulb.

14. Refit positon bulb

139 EMERGENCY AND BREAKDOWN ASSISTANCE 24 X 7 Road Assistance Response Time ** for the On Road  Park your vehicle on the edge of the Dear Customer, Assistance Program road, open the bonnet and put on the hazard warning signal. It is our responsibility and our endeavor Within City Lim- 60 minutes  Place the advance warning triangle to ensure that you have our complete its supplied with the vehicle approx. 3 m service backup if ever, wherever and On State or Na- from the vehicle in the direction of whenever you need the same. When you 90 minutes tional Highways oncoming traffic. have a road network that spans wide Ghat Roads and area, the probability of a breakdown 120 minutes +/- happening within hailing distance of a other places TATA MOTORS Authorized Workshop is **(The response time will depend on the very low. location, terrain, traffic density and the It is precisely for this reason, we have time of the day.) tied up with TVS AA, who will provide Standard procedure when calling breakdown assistance including towing for On Road Assistance in case of a to the nearest TATA MOTORS Authorized breakdown: Workshop through their Authorized Ser- vice Providers (ASP).  Dial the toll free help line number – 1800 209 7979 The 24X7 On Road Assistance Program  Identify your vehicle with the Vehicle shall be automatically available to your chassis number that is available in vehicle for the duration of Warranty pe- Coverage under 24 X 7 On Road As- the Owner’s Manual. riod. The program shall also be availa- sistance Program Explain your exact location with land- ble, if you avail the same post warranty.  I. The 24x7 On Road Assistance Pro- marks and tell us about the problem gram Service covers the following ser- you face with the vehicle. vices on your vehicle during warranty pe- riod.

140 EMERGENCY AND BREAKDOWN ASSISTANCE  Wheel change through spare wheel. both the plans- Basic and Premium. In  Lack of maintenance as per the the premium plan, this includes in-  Arrangement of fuel. (Fuel cost will 2 maintenance schedule as detailed in be chargeable at actual cost) stances of towing up to the nearest TATA the owner’s manual. MOTORS authorised workshop.  Re-opening the vehicle in cases of  Cases involving racing, rallies, vehi- key lock out. Exclusions cle testing or practice for such 24 X 7 On Road Assistance Program events.  Rectification of electrical problems does not apply to related to battery, fuses etc. Disclaimer  Cost of parts consumables and la-  On spot repairs for complaints repair-  The Service is not available in Lak- bour for such repairs not covered un- able at site. ^ shadweep. der warranty*. These charges are to  **The reach time is indicative & the  Vehicle to vehicle towing or winching be settled with ASP in cash. & towing for non-accident cases up actual reach time will be conveyed by  Toll or ferry charges paid by ASP in to the nearest TATA MOTORS author- the call centre at the time of break- reaching to the breakdown site to be ized workshop. Towing charges at ac- down call. settled with ASP in actuals in cash. tual cost beyond the same to be paid  The reach time can vary depending to the ASP in cash. (Any ferry or toll  Cases involving accident, fire, theft, on the traffic density & time of the charges levied in relation to the vehi- vandalism, riots, lightening, earth day. quake, windstorm, hail, tsunami, un- cle being towed to be paid by the cus-  The reach time indicated does not usual weather conditions, other acts tomers in actuals in cash). account for delays due to but not lim- of God, flood, etc. For accident cases, towing charges ited to acts of God, laws, rules & reg- to be borne by the customer.  Vehicles that are unattended, un-reg- ulations for time being in force, or- II. The 24x7 On Road Assistance Pro- istered, impounded or abandoned. ders of statutory or Govt. authorities, gram coverage on availing the 24X7 pol-  Breakdown/defects caused by mis- industrial disputes, inclement icy, post warranty is up to maximum of 6 use, abuse, negligence, alterations weather, heavy down pour, floods, instance of assistance in one year for or modifications made to the vehicle. storms, natural calamities, road blocks due to accidents, general 141 EMERGENCY AND BREAKDOWN ASSISTANCE strife and law & order conditions viz.  In case vehicle cannot be repaired  Vehicles will be handled, repaired & fire, arson, riots, strikes, terrorist at- on-site, customers are advised to towed as per the customer’s risk & tacks, war etc. use the towing facility for taking their TATA MOTORS shall not be liable for  ^ On spot repairs at breakdown site vehicle to the nearest TATA MOTORS any damages / claims as a result of shall depend on nature of com- authorized workshop only. In no con- the same. plaints & will be as per the discretion dition will the vehicle be towed to any  Services entitled to the customers of the ASP. unauthorized workshop. TATA MO- can be refused or cancelled on ac-  *The decision for free of charge re- TORS will not be responsible for any count of abusive behavior, fraudu- pairs will be as per the warranty pol- repairs carried out in such unauthor- lent representation, malicious intent icy & procedures of TATA MOTORS ized workshop. and refusal to pay the charges for LTD. and as per the interpretation of  Customer are advised to take ac- any charges related services and the same by ASP. You will be duly in- knowledgment from the ASP for the spare parts during service or on pre- formed by the ASP & call centre for list of accessories/extra fittings and vious occasion on part of the cus- the change applicable if any. other belongings in the vehicle as tomer.  All charges wherever applicable well as the current condition related  On site repairs may be temporary in need to be settled directly with the to dents/scratches breakages of nature. The completion of repairs ASP. parts/fitments of the vehicle at the does not certify the road worthiness time of ASP taking possession of the of the vehicle. The customer is ad- Exclusion of Liabilities vehicle & to verify these items when vised to ensure temporary repairs  It is understood that TATA MOTORS delivery is taken back by them, claim carried out onsite is followed by per- shall be under no liability whatsoever for loss of or damage to items, if any manent repairs at a TATA MOTORS in respect of any loss or damage aris- should be taken up with ASP directly. Authorized Workshop at the earliest. ing directly or indirectly out of any de- TATA MOTORS shall not be responsi-  Terms and conditions and service lay in or non-delivery of, defect/defi- ble for any such claims, dam- coverage, exclusions etc. are subject ciency in service/parts provided by ages/loss or any deficiency of ser- to change without notice. ASP. vice of the ASP.

142 EMERGENCY AND BREAKDOWN ASSISTANCE Vehicle Tracking System (VTS) Emergency (SOS) switch NOTE Vehicle Tracking System (VTS) is an Elec-  Please ensure that the VTS sys- tronic device fitted inside every Passen- tem is functional in the vehicle at ger vehicle (with Yellow plate registration all times otherwise, it will lead to used for commercial purpose), which op- violation of regulation. erates as a Taxi / Fleet for carrying pas- sengers. As per Govt. of India regulations  Any tampering, disconnection or (AIS: 140), it is mandatory to fit VTS in all bypassing of VTS system will send above-mentioned vehicles registered on the alerts to Government servers. or after 1st Jan. 2019. Customers may be liable for legal action for any such incidents. The emergency switches are provided in- Purpose:  Government servers may also side the vehicles. It shall be press by the monitor driver’s rash / negligent driver or any occupant in emergency like a) Efficient management of Transport driving behavior. accidents, medical emergencies & or System in the country. Law & order situations. If the occupant feels threatened or unsafe, then also b) To provide quick response & help in this can be used case of emergencies like accidents. NOTE c) Government servers may also moni- tor driver’s rash / negligent driving  After pressing the Emergency behavior. Switch, Police or Law enforcing agencies may track and intercept the vehicle. The occupants should be able to justify the usage of Emergency Switch to them. 143 EMERGENCY AND BREAKDOWN ASSISTANCE c) Un-intended Pressing of Emer- NOTE NOTE gency Switch:  After pressing switch, SOS (Safety  The flashing will continue until To avoid un-intentional pressing of Overflow Switch) symbol is not the authorized emergency ser- Emergency Switch, the flap is provide blinking; there is some fault in the vices attend to the request and on switch. However, if any occupant system that needs to be rectified. re-set the VTS system. If the Igni- presses the emergency switch by Please contact your nearest Tata tion is turn OFF, then also the SOS mistake, the emergency switch will Motors Authorised Service Center symbol will keep on Flashing. keep on flashing until it is re-set by for rectification emergency response server. The  Please note that Emergency Government agencies like Traffic Operation: Switches also work when Ignition Management & Police after verifying is Turned OFF. After pressing the the incident with the owner/driver of a) Ignition ON & switch not pressed: switch, SOS symbol will start During normal Ignition ON, the ‘SOS’ the vehicle will re-set the switch. flashing in above frequency. symbol on switch will flash continu- Tata Motors or its dealers will not be  If the SOS symbol inside Switch is ously as 0.1 Seconds ON ----4 Sec- able to re-set the system if Emer- not blinking even when Ignition is onds OFF - 0.1 Seconds ON- 4 Sec- gency Switch is press un-intention- ON, please check if your data plan onds OFF - --When Ignition is turn ally. OFF, it will switch OFF after some time. is expired. If data plan is active and still the SOS symbol is not b) Switch pressed blinking, contact your nearest In emergency, lift the flap and gently Tata Motors Authorised Service press the SOS symbol on switch for Center immediately to get this 0.5 seconds. The ‘SOS’ symbol on fixed. switch will flash continuously as Seconds ON - 0.5 Seconds OFF - -0.5 Seconds ON - 0.5 Seconds OFF---

144 EMERGENCY AND BREAKDOWN ASSISTANCE

Location of Switches: Activation of VTS System: NOTE Your dealer will help in activating the de- vice when it is install in the vehicle. If ac-  The VTS consumes battery even tivation is not done, SOS symbol inside when the Ignition is OFF. If the vehi- the switch will not flash. cle is park or not use for more than If despite activation if SOS symbol inside 10 days, it is advisable to start the emergency switch is not blinking, con- engine and keep the engine run- tact your nearest Tata Motors Authorised ning at 3000 rpm for at least 30 Service Center for rectification. minutes for re-charging the battery. Re-charging of Data Plan:  Always keep the Ignition in OFF po- The VTS system come with pre-loaded sition when vehicle is park or not data for 6 Months / 12 Months/24 being driven. For driver and front passenger months from the date of purchase of ve- hicle. After the data is consumed or after WARNING completion of bundled data period, the ! SIM needs to be re-charged. Your net- Warranty may be void in case:

work operator will inform you about the  Customer installs any other device/ data consumption & re-charging due accessories, which are not author- dates. Re-charge can be done by: ised by Tata Motors. Additional ac-

a) At Tata Motors Authorised Service cessories may lead to overloading of Center. Electrical System inside vehicle and b) By logging onto the network provider may reduce battery performance. portal.  Any tampering of the VTS device, For any support or further info, please Emergency Switches or it’s wiring For rear Passenger (LHS) contact your nearest Tata Motors Au- harness. thorised Service Center. 145 EMERGENCY AND BREAKDOWN ASSISTANCE

146 MAINTENANCE Maintenance and Service The following checks can be carried out between the recommended scheduled WARNING ! Periodic maintenance is essential for en- maintenance services. Take help of our suring long trouble free performance.  Be careful not to touch a hot en- authorized service centre for assistance. gine, exhaust manifold and Have your vehicle serviced regularly  Engine oil level pipes, muffler, radiator and wa- from TATA MOTORS Authorized Service ter hoses.  Engine coolant level Centre.  Do not work on a vehicle with the  Brake fluid level There is a large network of TATA MO- engine running in an enclosed  Washer fluid level checking & top- TORS Authorized Service Centre’s to space, unless you are sure you help you with their professional servicing ping up have enough ventilation. expertise. Scheduled maintenance infor-  Battery electrolyte level  Keep all open flames and other mation is provided which makes tracking  Tyre inflation pressure including burning material (such as ciga- routine service easy. spare wheel rettes) away from the battery and all fuel related parts.

 If you need to do any work inside NOTE the engine compartment, Refer “Opening and Closing” section  Switch off the ignition

for engine bonnet opening.  Never reach into the area where there is a risk of danger from moving components, such as the fan rotation area.  Keep clothing away from moving parts.

147 MAINTENANCE Engine Compartment – Diesel

1. Brake fluid reservoir 4. Windshield washer container 7. Battery 2. Dip Stick - Engine Oil 5. Air Filter 8. Auxiliary tank 3. Engine oil filling cap 6. Fuse & relay box

148 MAINTENANCE Engine Compartment – Petrol (MT)

1. Dip Stick - Engine Oil 4. Windshield washer container 7. Battery 2. Brake fluid reservoir 5. Air Filter 8. Auxiliary tank 3. Engine oil filling cap 6. Fuse & relay box

149 MAINTENANCE Engine Compartment – Petrol (AMT)

1. Dip Stick - Engine Oil 4. Windshield washer container 7. Battery 2. Brake fluid reservoir 5. Air Filter 8. AMT oil reservoir 3. Engine oil filling cap 6. Fuse & relay box 9. Auxiliary tank

150 MAINTENANCE Engine Oil Level NOTE Warm up the engine to normal operating temperature. • Do not remove the filler cap when the engine is running. Turn it ‘OFF’ and wait for 5 minutes for • Do not add oil above than the the oil to return to the oil pan. Be sure MAX. mark. Oil level above the the vehicle is on a level surface. MAX. mark may cause engine Take out the dipstick, wipe it clean, and damage. reinsert if fully. Pull it out again and ex- For location of Engine oil filling cap amine the oil level. It should be between and dip stick, please refer respective ‘MIN’ and ‘MAX’ level. If not, top up with Engine Compartment pages. recommended engine oil. Diesel

NOTE The oil consumption depends up-on the driving style and the conditions under which the vehicle is used.

Petrol

151 MAINTENANCE Brake Fluid Level For location of Brake Fluid Container and filling cap, please refer respective NOTE Engine Compartment pages. In case of emergency, a large Engine Coolant Level amount of water without engine cool- ant may be added in order to reach a vehicle service location. Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle to confirm correct level. For location of Engine coolant con- The level of the brake fluid should be be- tainer and filler cap, please refer re- tween the ‘MIN’ and ‘MAX’ marks on the spective Engine Compartment pages. side of the brake fluid container. If the level falls below the ‘MIN’ mark, add rec- Check whether the coolant level is be- NOTE ommended brake fluid. tween the ‘MIN’ and ‘MAX’ marks on the Topping of the coolant should be coolant reservoir. done in the auxiliary tank only. NOTE When the coolant levels is low, top up Do not allow brake fluid to make con- with recommended coolant through filler tact with the skin or eyes. of auxiliary tank until the level ap- Do not allow brake fluid to splash or proaches the max level line. Refer ‘Tech- spill on the paint surface as it will nical information’ section.

152 MAINTENANCE Make sure that only TATA MOTORS rec- Checking AMT oil reservoir level Windshield Washer Fluid Level ommended coolant is used. Mixing of Check that there is washer fluid in the different coolants may harm your en- tank. Refill it if necessary. Use a good gine’s cooling system and its compo- quality windshield washer fluid, diluted nents. Do not add extra inhibitors or ad- with water as necessary. ditives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant. NOTE • Do not use detergent or any other WARNING ! additive in the windshield washer reservoir. This can severely im- The engine cooling system is pressur- pair visibility when sprayed on ized, particularly when the engine is the windshield, and can damage warm. When opening the cap, you your vehicle’s paint. could be scalded by hot coolant The level of the AMT oil reservoir level • Do not operate washer motor spraying out. There is a risk of injury. should be between the ‘MIN’ and ‘MAX’ marks on the side of the container. If the with no fluid in washer tank, Let the engine cool down before level falls below the ‘MIN’ mark, add rec- washer motor will be damaged opening the cap. Wear eye and hand ommended oil. protection when opening the cap. Open the cap slowly half a turn to al- For location of Windshield Washer low pressure to escape. Container and filling cap, please refer respective Engine Compartment pages.

153 MAINTENANCE Battery  Ensure that the battery is securely NOTE  Check the battery for electrolyte level mounted. against the marking on the battery  If you need to connect the battery to • During normal operation, the bat- outer case. a charger, disconnect both cables to tery generates gas, which is ex-  Check the battery terminals for cor- prevent damage to the vehicle’s plosive in nature. A spark or open flame can cause the battery to rosion (a white or yellowish powder). electrical system. explode causing very serious inju- To remove it, wash the terminals with For location of battery, please refer ries. a solution of baking soda. It will bub- respective Engine Compartment • Keep all sparks, open flames and ble up and turn brown. pages smoking materials away from the  When this stops, wash it off with battery.

plain water. Dry off the battery with a • The battery contains sulphuric cloth or paper towel. acid (electrolyte) which is poi-  Coat the terminals with petroleum sonous and highly corrosive in jelly to prevent future corrosion. nature. Getting electrolyte in your eyes or on the skin can cause se-  Use a proper wrench to loosen and vere burns. Wear protective

remove cables from the terminals. clothing and a face shield or have  Always disconnect the negative (-ve) a skilled technician to do the bat- cable first and reconnect it last. tery maintenance.

 Clean the battery terminals with a terminal cleaning tool or wire brush.  Reconnect and tighten the cables, coat the terminals with petroleum jelly. 154 MAINTENANCE Spark Plug (Petrol) Tyres Inflation Check for inflation and condition of your vehicle tyres periodically. Check the pressure in the tyres when they are cold. Keeping the tyres properly inflated gives you the best combination of riding com- fort, handling, tyre life and better fuel ef- ficiency. Over inflation of tyres makes the vehicle ride bumpy and harsh. Tyres are more prone to uneven wear and damage from

Spark Plug Number Gap road hazards. Under Excessive side Under inflated tyres reduce your comfort 0.7 to BOSCH YR7SES 1 0.8 mm inflation tread wear in vehicle handling and are prone to fail- ures due to high temperature. They also Federal Mogul RER8MC 0.8 to Correct tyre cause uneven wear and more fuel con- Uniform wear (Champion) 0.9 mm 2 pressure sumption. Tightening Torque - 25 Nm Excessive NOTE 3 Over inflation center tread NOTE wear Every time you check inflation pres- sure, you should also examine tyres for Use spark plug of recommended damage, trapping of foreign objects in make & type for replacement. the treads and wear.

155 MAINTENANCE Recommended tyre pressures Tyre pressure sticker location Special care for tubeless tyres:  While removing tyre from wheel rim Tyre Ver- Tyre Wheel size sion pressure and mounting it back on wheel rim, take precautions not to damage tyre 33 psi Front bead. Use tyre removal and assem- (2.3 bar) bly machines. Damage or cut on tyre 30 psi Petrol Rear bead may cause gradual loss of air (2.1 bar) and deflation of tyre. 36 psi 175/65 Spare  Do not scratch inside of tubeless tyre (2.5 bar) R14 & with metallic or sharp object. Tube- 33–36 psi 155/80 less tyres are coated with impermea- R13 Front (2.3 -2.5 bar) NOTE ble layer of rubber from inside which Diesel 30 psi holds the air inside the tyre. Removal Rear  Maintain tyre inflation pres- (2.1 bar) of this layer due to scratching may sure as per the specific men- 36 psi cause gradual loss of air and defla- Spare tioned in tyre pressure sticker (2.5 bar) tion.  Regular tyre and spare tyre to 36 psi  If wheel rim gets damaged in service, Front be checked for correct tyre in- (2.5 bar) get the wheel rim repaired/ replaced flation pressure at least once 175/60 36 psi Petrol Rear a month immediately. Running the vehicle R15 (2.5 bar) with damaged rim may cause defla- 36 psi Spare tion of tyre and subsequent dislodg- (2.5 bar) ing of tyre from rim.

156 MAINTENANCE  Maintain recommended inflation Tyre rotation For 175/65 R14 and 175/60 R15 tyres pressure. Over-inflation, in particu- with temporary spare wheel (if To help increase tyre life and distribute equipped) lar, may cause puncture or bursting wear more evenly you should have tyres of tyre. rotated at specified intervals or earlier depending on the operation of vehicle. NOTE The illustrations show how to rotate tyres Life and wear pattern of tyres de- when normal or temporary spare wheel pends on various parameters like is fitted. tyre pressure, wheel alignment, For 155/80 R13 tyres wheel balancing, tyre rotation, etc. It also largely depends on vehicle speed, load carried, usage, driving NOTE habits, road conditions, tyre quality,  Do not use spare wheel for tyre ro- etc. In case fault is suspected to be tation, in case of temporary spare due to poor quality of tyres, the same wheel used. may be taken up with concerned tyre  Two or more temporary tyres manufacturer. should not be used on one vehi- cle.  Tyre pressure of temporary wheel is to be checked at least once in in a month.

157 MAINTENANCE Wheel Alignment Wheel Balancing Remote Key Battery Replacement Incorrect wheel alignment causes exces- Wheels of your vehicle are balanced for Remote control key contains a battery sive and uneven tyre wear. Check wheel better ride comfort and longer tyre life. which is housed under the cover. alignment at specified intervals. Wheel Balancing needs to be done whenever If red LED remote flashes for 5 times af- alignment values are given below: tyre is removed from rim. ter placing and releasing any button on remote. It is recommended to replace Front Rear WARNING ! battery at a TATA MOTORS Authorised If the vehicle vibrates abnormally on Service Centre. Caster 1º 45’ ± 45’ - a smooth road, have the wheel bal- You should, however, proceed as follows anced done immediately. Camber 30’ ± 30’ - 52’ ± 60’ if you wish to replace the discharged bat- tery yourself:

Toe in - 12’ ± 15’ 1. Open the key blade. 2. Press off the battery cover with your Toe Out 0 to 13’ - thumb or using a flat screw driver at the points of the arrows.

3. Remove the discharged battery from the key by pressing the battery down- wards at the point of the arrow.

158 MAINTENANCE 5. Ensure that the “+” symbol on the The OBD system also has a diagnostic battery is facing upwards. The cor- connector that can be interfaced with rect polarity is shown on the battery appropriate diagnostic tools, which makes it possible to read the fault codes cover. stored in the Electronic Control Unit, to- 6. Position the battery cover on the key gether with a series of specific parame- and press on it until it is heard to lock ters for Engine operation and Diagnosis. in place. This check can also be carried out by the traffic police. NOTE To access the diagnostic connector, open the fuse box cover which is located Use CR 2032 battery only. on RH side below the steering wheel. Re- 4. Insert the new battery. fer ‘Emergency and Breakdown Assis-

On Board Diagnostic (OBD II) System tance’ section for removal of cover. On board Diagnostics or OBD is an auto- motive term referring to a vehicle’s self- diagnostic and reporting capability. The OBD system allows continuous diagno- sis of the components of the vehicle cor- related with emissions. This system warns the driver, by turning “ON” the Malfunction Indication lamp (MIL) on the instrument cluster, when a fault causes emission levels to increase.

159 MAINTENANCE Service Instructions The TATA TIGOR has been manufactured to give you econom- ical and trouble free performance. To achieve this, please fol- Servicing of the vehicle can be done at any TATA MOTORS low the instructions as stated. Authorised Dealer Workshop or TATA MOTORS Authorised Service Centre (TASC). Your vehicle is entitled to three free services (labour only). The free service coupons are attached to the sales invoice. Please Warranty claims can be settled by any TATA MOTORS Author- present these coupons to the servicing dealer while availing ised Dealer Workshop or TATA MOTORS Authorised Service free services. Centre (TASC).

1st free service - At 1000-2000 kms. OR 2 months, whichever is earlier.

2nd free service - At 7000-8000 kms. OR 6 months, whichever is earlier. 3rd free service - At 14500-15500 kms. OR 12 months, which- ever is earlier. All services other than free services are chargeable.

160 MAINTENANCE Service Schedule

K

K

0

5K

PDI

15K 30K 45K 60K 75K 90K

1. 7.5K Sr. Kms

105K 120K 135K 15

22.5K 37.5K 52.5K 67.5K 82.5K 97.5K

Operation 112.5K 127.5K 142.5 No. Months 0 2 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120

General

Wash the vehicle Every 1 & Clean Con- ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● denser Fins Service Check & Top up Fluids (If re- quired): Trans- axle Oil, Coolant, Every 2 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Brake Fluid, Bat- Service tery Electrolyte, Wind Screen washer fluid.

Check Fuel Every 3 Lines for Leak- ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ages. Service Check and Cap- ture all DTC's Every 4 Clear all faults ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● and Erase the Service Codes. Check Rubber Boots for dam- 15K / 5 age & replace if ● ● ● ● ● ● ● ● ● ● 12M required (driveshaft)

# - Kms or Months whichever occurs earlier

161 MAINTENANCE

K

K

5K

PDI

15K 30K 45K 60K 75K 90K

1. 7.5K Sr. Kms

105K 120K 135K 150

22.5K 37.5K 52.5K 67.5K 82.5K 97.5K

Operation 112.5K 127.5K 142.5 No. Months 0 2 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120 Check Rubber Boots, Rubber seat, Dust cover & Bushes for damage & re- 7.5K / 6 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● place if required 6M (Suspension) (First at 15K/12M then at every service) Check for all 7.5K / 7 bolts & nuts ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 6M (Tighten)

Engine (Diesel) Clean air filter el- ement (more fre- 15K / 1 quently for vehi- ● ● ● ● ● ● ● ● ● ● 12M cle operating as TAXI)

Change engine 15K / 2 ● ● ● ● ● ● ● ● ● ● oil and Oil filter 12M

Drain water from 15K / 3 ● ● ● ● ● ● ● ● ● ● Fuel Filter Bowl 12M

Replace Fuel Pre filter assem- # 45K / 4 ● ● ● bly (WIF Sensor 24M to be reused) Replace Fuel # 135K / 5 Main fuel filter ● 24M assembly

# - Kms or Months whichever occurs earlier 162 MAINTENANCE

K

K

0

5K

PDI

15K 30K 45K 60K 75K 90K

1. 7.5K Sr. Kms

105K 120K 135K 15

22.5K 37.5K 52.5K 67.5K 82.5K 97.5K

Operation 112.5K 127.5K 142.5 No. Months 0 2 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120

Replace Diesel - # 75K / 6 Pressure Regu- ● ● 36M lator Check accessory belt condition vis- 15K / 7 ● ● ● ● ● ● ● ● ● ● ually, replace if 12M found damage Check timing belt visual condition, # 105K / 8 ● replace if found 24M damage Replace air filter element (more 45K / 9 frequently for ve- ● ● ● 36M hicle operating as TAXI)

# 60K / 10 Change coolant ● ● 36M

Replace timing drive kit (Timing # 150K / 11 ● belt, Auto ten- 36M sioner and Idler)

# - Kms or Months whichever occurs earlier

163 MAINTENANCE

K

K

5K

PDI

15K 30K 45K 60K 75K 90K

1. 7.5K Sr. Kms

105K 120K 135K 150

22.5K 37.5K 52.5K 67.5K 82.5K 97.5K

Operation 112.5K 127.5K 142.5 No. Months 0 2 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120

Engine (Petrol) Clean air filter el- ement (more fre- 15K / 1 quently for vehi- ● ● ● ● ● ● ● ● ● ● 12M cle operating as TAXI)

Change engine 15K / 2 ● ● ● ● ● ● ● ● ● ● oil and Oil filter 12M

Gasoline - Re- 75K / 3 ● ● place Fuel Filter 60M

Change Spark 45K / 4 ● ● ● plugs 36M

Check accessory belt condition vis- 15K / 5 ● ● ● ● ● ● ● ● ● ● ually, replace if 12M found damage Replace air filter element (more 45K / 6 frequently for ve- ● ● ● 36M hicle operating as TAXI) Change coolant (60K /36M , # 60K / 7 ● ● whichever 36M comes early)

# - Kms or Months whichever occurs earlier

164 MAINTENANCE

K

K

0

5K

PDI

15K 30K 45K 60K 75K 90K

1. 7.5K Sr. Kms

105K 120K 135K 15

22.5K 37.5K 52.5K 67.5K 82.5K 97.5K

Operation 112.5K 127.5K 142.5 No. Months 0 2 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120

Transaxle Replace trans- 75K / 1 ● ● axle oil 60M Check AMT Kit oil level, it should be in between min. & Max. level when Every 2 the vehicle is in Ser- ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● standstill and vice ignition ON condi- tion. Top up AMT kit oil if necessary.

Brakes Check front brake pads & 15K / 1 rear brake lin- ● ● ● ● ● ● ● ● ● ● 12M ings. Replace if necessary Replace brake fluid Check # 45K / 2 brake system ● ● ● 24M components for Leakages Inspect & if nec- essary adjust 15K / 3 ● ● ● ● ● ● ● ● ● ● handbrake set- 12M ting

# - Kms or Months whichever occurs earlier

165 MAINTENANCE

K

K

5K

PDI

15K 30K 45K 60K 75K 90K

1. 7.5K Sr. Kms

105K 120K 135K 150

22.5K 37.5K 52.5K 67.5K 82.5K 97.5K

Operation 112.5K 127.5K 142.5 No. Months 0 2 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120

Wheels & Tyres Check & Adjust # 15K / 1 ● ● ● ● ● ● ● ● ● ● Wheel alignment 18M

Check for Tyre # 7.5K / ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 2 pressure, condi- 12M tion & rotate

Electrical Check specific gravity of battery Every 1 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● electrolyte (OR Service Every 6 Months)

Check headlamp 15K / 2 ● ● ● ● ● ● ● ● ● ● focussing 12M

A.C. System Clean filter and check Air-condi- tioning / HVAC Every 1 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● system for satis- Service factory perfor- mance

# - Kms or Months whichever occurs earlier

166 MAINTENANCE Vehicle Parking at One Place for sheets of imperforated plastic as Long Duration they do not allow moisture on the ve- (Non - Use Maintenance) hicle body to evaporate. 9. Inflate the tyres to 0.5 bar above the If you want to park your vehicle at one normal specified pressure and check place for long duration, following care is it at regular intervals. to be taken: 10. Check the battery charge every six weeks. 1. Park the vehicle in covered, dry and if possible well-ventilated premises. 11. Do not drain the engine cooling sys- Engage a gear. tem.

2. Remove the battery terminal cables (first remove the cable from the neg- ative terminal). 3. Block the wheel or engage in the gear mode. 4. Clean and protect the painted parts using protective wax. 5. Clean and protect the shiny metal parts using commercially available special compounds. 6. Sprinkle talcum powder on the rub- ber windscreen wiper and lift them off the glass. 7. Slightly open the windows. 8. Cover the vehicle with a cloth or per- forated plastic sheet. Do not use

167 MAINTENANCE

168 TECHNICAL INFORMATION Fuel Specification The supplementary fuel to be used like kerosene. Ratio for mix- ing of supplementary fuel and diesel are shown in the table. Fuel (Diesel) Normal grade BS IV compliant diesel conforming to IS1460 Percentage or EN 590 or equivalent is recommended to be used as fuel. Ambient Tempera- ture up to Deg C. Summer grade Supplementary Do not use premium diesel available in the market for exam- diesel fuel ple extra premium / Turbojet etc. Up to 0 100 0 Recommended fuel specifications 0 to -10 70 30 Parameter Unit BS IV -10 to -15 50 50 Cetane Number (min) C N 51 Care should be taken that diesel and supplementary fuel are Sulphur content mg/kg 50 thoroughly mixed before filling. Lubricity (HFRR) micron 460 Percentage Ambient Temper-

ature upto Deg C. Winter grade Supplementary diesel fuel NOTE Up to -15 100 0 Where oxidation catalytic converter is fitted, it is manda- -15 to -20 70 30 tory to use Diesel fuel with Sulphur contents as given above. Use of any other diesel fuel can increase the pol- -20 and below 50 50 lutants.

At very low temperature, fluidity of diesel may become insuffi- WARNING ! cient due to paraffin separation. It is therefore necessary to Do not mix gasoline or alcohol with diesel. This mixture can mix supplementary fuel with summer or winter grade diesel. cause an explosion. 169 TECHNICAL INFORMATION Fuel (Petrol) Unleaded regular grade petrol conforming to IS 2796:2008 and BS IV specification and RON not less than 91 is recommended. It is always recommended to use correct fuel to get optimum emission performance.

NOTE Always use petrol of a correct specification in a vehicle fit- ted with catalytic converter. Even single fill of leaded petrol will seriously damage the catalytic converter.

!

170 TECHNICAL INFORMATION Lubricant Specification Use following genuine fluids, coolants and lubricants recommended for optimum performance of your vehicle.

Item Specification Company Brand Quantity

CASTROL Magnatec Professional T 5W30

5W30 ACEA Mobil super 3000 TMGO 5W 30 Tata motors EXXON MOBIL Petrol - 3.5 L Engine Oil A5/B5 TATA genuine oil Diesel - 4.5 L SS6576 TATA MOTORS GENUINE OIL – Engine Oil synth PETRONAS 5W30

Coolant (Pre- Sunstar CCI Gloden Cruiser LLC2200NP mixed) (Anti- Class II/JIS Petrol – 5.5 L freeze agent K2234 TATA CASTROL Castrol Radicoolant SFO Premix + Soft water SS7700S1 Diesel – 6.5 L 40 : 60 ratio) IOCL TATA MOTORS GENUINE COOLANT KOOL PLUS TATA MOTORS Genuine Oil – Gear Oil New PETRONAS Gen 80 EP LL EP80W LL Transaxle Oil (Next Gen) IOCL TATA MOTORS GENUINE GEAR OIL 80WLL 1.8 Liters TATA SS6582 CASTROL Transmax Manual T 80W

171 TECHNICAL INFORMATION

Item Specification Company Brand Quantity

PETRONAS TATA MOTORS Genuine Brake Oil PETRONAS DOT 4S Brake SAE J1703, Fluid/Clutch Golden Cruiser Tata Genuine Brake Fluid As required DOT4 Sunstar CCI fluid (DOT4)

CASTROL CASTROL-Universal Brake Fluid DOT 4

Refrigerant R-134a MAHLE - 500 gms

Compressor Oil ND-8 MAHLE - 120 ml

AMT Kit oil Hydraulic Oil PETRONAS TUTELA Cs – Speed As required

NOTE

Check AMT Kit oil level at every service, it should be in between min. & max. level when the vehicle is in standstill and ignition ON condition. Top up AMT kit oil if necessary.”

172 TECHNICAL INFORMATION Technical Specifications Parameter Diesel Model/type 1.05 CRAIL Turbocharger Intercooled Diesel 1.2 REVOTRON Capacity 1047 cc 1199 CC

Max. Engine output 51.5 kw (70 ps) @ 4500 rpm 62.5 kw (85 ps) @ 6000 rpm

Max. Torque 140 Nm @ 1800 to 3000 rpm 114.4 Nm @ 3500 +/-70 rpm

Clutch Type Single plate dry friction diaphragm type Outside diameter of 200 mm clutch Transaxle TA-65* 5/3.83 (5 speed) with overdrive Model TA-65* 5/3.64 (5 speed) with overdrive manual manual Type Synchromesh on all forward gears and sliding mesh on reverse gear No. of gears 5-Forward, 1-Reverse

173 TECHNICAL INFORMATION Parameter Diesel Petrol Steering Type Electrical Power assist Steering, Rack & Pinion Gear, Collapsible Steering Column Brakes Brakes Front (Disc); Rear (Drum) Parking brake Cable Operated Mechanical (Variable Lever Ratio) Suspension Type Independent Shock absorber Hydraulic Shock absorber Wheels & tyre 1. 155/80 R13 79T Tubeless (XE, XE(O)) 1. 155/80 R13 79T Tubeless (XE, XE(O)) 2. 175/65 R14 82T Tubeless (XM, XM(O), XT Tyres 2. 175/65 R14 82T Tubeless (XM, XM(O),XT, XT(O), XTA) XT(O), XZ, XZ(O), XZ+ 3. 175/60 R15 Tubeless (XZ, XZ(O), XZ+, XZA) 1. 4.5JX13" Steel Wheel Rim (XE, XE(O)) 1. 4.5JX13" Steel Wheel Rim (XE, XE(O)) 2. 5J X 14" Steel Wheel Rim (XM, XM(O),XT, 2. 5J X 14" Steel Wheel Rim (XM, XM(O), XT, Wheel rims XT(O), XTA) XT(O), 3. 5.5J X 15" Alloy Wheel Rim (XZ, XZ(O), XZ+, 3. 5J X 14" Alloy Wheel Rim (XZ, XZ(O), XZ+) XZA) Suspension Type 35 liters

174 TECHNICAL INFORMATION

Parameter Diesel Petrol Cab / body Type Semi-mono volume, 4 doors , steel monocoque body. Electrical system System voltage 12 Volts (-ve earth) Alternator capacity 14.5V,120 Amp 14.5 V, 110 Amp Battery 12V, 50Ah 12V, 44Ah Main chassis dimension (in mm) Wheel base 2450 Track front 1400 Track rear 1420 Overall length 3992 Overall height 1537 Max. Width 1677 Ground clearance 165 Performance Max. Speed 150 Kmph 160 Kmph Max. Recom- 14 deg mended gradability Minimum Turning 10.1 m Circle Dia.

175 TECHNICAL INFORMATION

Parameter Diesel Petrol Minimum Turning Clearance circle 11 m Dia. Weight (in kg) 1420 XE, 1435 XE(O) 1485 XE, 1500 XE(O) 1422 XM, 1437 XM(O) 1490 XM, 1505 XM(O) 1442 XT, 1457 XT(O) Gross vehicle 1510 XT, 1525 XT(O) 1457 XZ, 1462 XZ(O) weight 1525 XZ, 1530 XZ(O) 1442 BUZZ, 1462 XZ+ 1510 BUZZ, 1530 XZ+ 1454 XTA, 1454 XMA 1469 XZA, 1469 XZA+ 1020 XE, 1035 XE(O) 1085 XE, 1100 XE(O) 1022 XM, 1037 XM(O) 1090 XM, 1105 XM(O) 1042 XT, 1057 XT(O) Kerb weight 1110 XT, 1125 XT(O) 1057 XZ, 1062 XZ(O) (Unladen) 1125 XZ, 1130 XZ(O) 1042 BUZZ, 1062 XZ+ 1110 BUZZ, 1130 XZ+ 1054 XTA, 1054 XMA 1069 XZA, 1069 XZA+

176 TECHNICAL INFORMATION Vehicle Dimensions

177 TECHNICAL INFORMATION Aggregate Identification Numbers

Chassis No. punching near driver seat Transaxle No. Punching Engine No. Plate – Petrol

VIN plate near front passenger seat Engine No. Plate – Diesel 178 CAR CARE AND VALUE ADDED SERVICES Car Care 4. To remove stubborn stains and con- After drying the vehicle, inspect it for taminants like tar, use turpentine or chips and scratches that could allow cor- Your vehicle is subjected to many exter- cleaners like ‘Stain remover’, which rosion to start. Apply touch up paint nal influences such as climate, road con- are safe for, paint surfaces. where necessary. ditions, industrial pollution and proximity 5. Avoid substances like petrol, diesel, to the sea. These conditions demand kerosene, benzene, thinner or other Cleaning of Carpets regular care of the vehicle body. Dirt, in- solvents that cause damage to paint. sects, bird droppings, oil, grease, fuel Vacuum clean the carpet regularly to re- 6. Dry your vehicle thoroughly to pre- move dirt. Dirt will make the carpet wear and stone chippings should be removed vent any damp spots. out faster. Periodically shampoo the car- as soon as possible. 7. Rinse all surfaces thoroughly to pre- pet to keep it looking new. Washing vent any traces of soap and other cleaners as this may lead to the for- Use carpet cleaners (preferably foam Following these tips while washing your mation of stains on the painted sur- type). Follow the instructions that come vehicle. face later. with the cleaner. Apply it with a sponge or soft brush. Keep the carpeting as dry Hand wash: as possible by not adding water to the WARNING 1. Always wash your vehicle in shade ! foam. and the surface is at room tempera- Do not direct high-pressure washer ture. fluid/ water jets (Pressure above 0.5 NOTE 2. Wash with mild vehicle wash soap Bar) at electrical devices and con- like ‘Car Shampoo’ and use a soft necter during washing. This is to pre- Avoid wiping of painted surface in dry bristle brush, sponge or soft cloth vent malfunction / failure of electri- condition as it may leave scratches and rinse it frequently while washing cal system due to water ingress. on the painted surface. to avoid scratches. 3. To avoid scratches, please wear soft gloves. Remove finger rings, nails, wristwatch while washing.

179 CAR CARE AND VALUE ADDED SERVICES Cleaning of Windows, Front and Waxing Interior fabric cleaning tips

Rear Glasses Waxing and polishing is recommended 1. Stains should be treated immedi- Clean the windows inside and outside to maintain the gloss and wet-look ap- ately. If left for a long time, they can with commercially available glass clean- pearance of your paint finish. leave a permanent mark. ers. 2. Cleaning the stains immediately is Use good quality polish and wax for 1. important especially for stains which This will remove the haze that builds up your vehicle. contain artificial colors in the stain Re-wax your vehicle when the water on the inside of windows. Use a soft 2. creating liquid or semisolid sub- does not slip off the surface but col- cloth or paper towels to clean all glass stance. The colorant may leave a lects over the surface in patches. and plastic surfaces. stain if kept for longer time. FAST TAG Polishing 3. Stain should not be removed by rub- bing. As far as possible, try to blot or FAST TAG is pasted on front windshield Polishes and cleaners can restore shine lift the stain with cloth or plastic spat- from the inside. It enables Electronic toll to the painted surface that has oxidized ula and then clean the remaining collection. and become dull. They normally contain stain with cloth or sponge. mild abrasives and solvents that remove 4. If the stain has dried, then gently the top layer of the finish coat. Polish brush off the material and then press your vehicle, if the finish does not regain with damp cloth or sponge till it dis- its original shine after using wax. appears.

5. Do not use household detergents to clean the fabric. NOTE 6. Always use clean cotton cloth for Do not attempt to rip or tamper the cleaning. tag. It will disable the functionality of the tag.

180 CAR CARE AND VALUE ADDED SERVICES Paint Care Periodic Inspection Following guidelines will help you to pro-  Regularly inspect your vehicle for any tect your Vehicle from corrosion effec- damage in the paint film such as tively. deep scratches and immediately get Proper cleaning them repaired from an authorized service outlet, as these defects tend In order to protect your vehicle from cor- to accelerate corrosion. rosion it is recommended that you wash  Inspect mud liners for damages. your vehicle thoroughly and frequently in  Keep all drain holes clear from clog- case: ging.  There is a heavy accumulation of dirt Proper Parking and mud especially on the under- body.  Always park your vehicle in shade to  It is driven in areas having high at- protect it from harsh sunlight or in a mospheric pollution due to smoke, well-ventilated garage so that there soot, dust, iron dust and other chem- is no dampness on any part of the ve- ical pollutants. hicle.  It is driven in coastal areas. Wiper care  The underbody must be thoroughly pressure washed after every three  To prevent damage to the wipers or months. windshield, do not operate the wip- ers when the windshield is dry. In addition to regularly washing your car, To prevent damage to the wiper arms the following precautions need to be  and other components, do not at- taken. tempt to move the wipers manually.

181 CAR CARE AND VALUE ADDED SERVICES Extended Warranty TATA MOTORS recommends the purchase of its extended warranty program. Coverage - Mechanical + Electrical Benefits  Insures you against unforeseen break down repair bills.  Documentation is simple and hassle free.  Near cashless & speedy claim Term 24 + 12 months or 75,000 kms whichever occurs first OR

24 + 24 months or 1,00,000 kms whichever occurs first Extended Warranty is available in the dealership from where you have purchased your vehicle. We strongly recommend purchase of Extended Warranty at time of purchase of your vehicle. Extended Warranty can be availed till 421 days from date of purchase of vehicle. The Dealer Service Marketing Executive shall explain to you the Terms and conditions, Coverage and Owner’s respon- sibility. Extended Warranty Booklet & Cover Note The Extended Warranty booklet and cover note is the basis of the contract between TATA MOTORS LIMITED and the Owner of the vehicle shown on the Extended Warranty booklet. The Customer is to retain this booklet and the same to be produced to the dealer while claiming benefit s under Extended Warranty.

182 CAR CARE AND VALUE ADDED SERVICES Note  The 12 or 24 months extended warranty does not follow the 24 months Manufacturer's warranty.  The extended warranty comes into force once the manufacturer’s warranty expires e.g. after 24 Months.  It is more restrictive as by the time it comes into force the vehicle is already 24 months old. What is covered?  Mechanical / Electrical break down as defined in this warranty and confirmed by the dealer within the stipulated terms and conditions.  TATA MOTORS dealer shall either rep air or replace any part found to be defective with a new p art or an equivalent at no cost to the owner for p arts or labour.  Such defective parts which have been replaced will become property of TATA MOTORS LIMITED.  Comprehensive list of parts covered is mentioned in the page 9-12 of the Extended Warranty Booklet. What is not covered? Please refer the Extended Warranty Booklet for details of the exclusion list. Owner’s Responsibility:  Proper use, maintenance and care of the vehicle in accordance with the instructions contained in the Owner’s Manual and Service Booklet. The records of the same to be ensured in Owner’s Manual.  Retention of maintenance service bills.

I / We have been explained the Terms and conditions, Coverage and Owner’s responsibility by the Dealer Service Marketing Executive. I wish to avail / Do not wish to avail extended warrant policy.

Customer’s Signature Dealer’s Signature

183 CAR CARE AND VALUE ADDED SERVICES Value Added Services Why are Corrosion Protection Waxes neces- sary? Corrosion is caused by: Water / salt water acid rain & atmospheric fallouts. Critical areas are: Cavities: joints, crevices, spot welds, underbody  Corrosion is the most important factor when we talk about the vehicle life. If you treat your car you can prolong the life.  It is very dangerous to drive around in a corroded vehicle.  The corrosion creeps onto the vehicle from the inside and from the outside. The most dangerous kind of corrosion is often not discovered until it is too late. Benefits of Anti - Rust treatment:  A professionally applied range of world class products offering real value to the new and used vehicle customer.  The treatment has been developed to withstand the harshest environmental and climatic conditions (rust. Pollutants, stone and gravel impact, etc.)  Insulate cabin space from external noises.  Expensive tin work and Denting / Painting avoided.  Higher resale value for the vehicle.  Higher safety – uncorroded vehicle  10 free checkups available

184 CAR CARE AND VALUE ADDED SERVICES TATA MOTORS has tied up with M/s Wurth, M/s Autokrom, M/s 3M India Lt d & M/s Bardahl for these world class treatment at affordable prices. These treatments are available in all authorized workshops. The Dealer Service Marketing Executive will explain to you the benefits and terms and conditions of this treatment.

I / We have been explained the Benefits, Terms and conditions and the prices of these treatments by the Dealer Service Marketing Executive. I wish to avail / Do not wish to avail extended warrant policy.

Customer’s Signature Dealer’s Signature

185 CAR CARE AND VALUE ADDED SERVICES Vehicle Exterior Enrichment

Why vehicles are painted?  For Corrosion protection of the metal surfaces.  Ease of application from other corrosion protection treatments.  Cheaper than other corrosion protection methods eg. Galvanizing, ano- dizing.  For decoration and identification. Various Environmental Hazards affecting paints Environmental hazards: destroy your vehicle's finish. Even as your new vehicle rolls off the assembly line, the paint is not protected.

The enemy Ultraviolet Rays, Pollution, Tree Sap, Bird Droppings, Car Wash Chemicals, Road Salt, Acid Rain.

Benefits: Vehicle Exterior Enrichment  Removal of medium scratches, orange peel, oxidation, dust nibs etc. & swirl marks from painted surface.  Restoration of original gloss levels, UV protection after gloss is restored.  Cleaning & dressing of tyres, Bumpers & all exterior plastic moldings/trims. TATA MOTORS has tied up with M/s Autokrom, M/s 3M & M/s Wurth for this world class treatment at affordable prices. This treatment is available in all authorized workshops. The Dealer Service Marketing Executive will explain to you the benefits and terms and conditions of this treatment.

186 CAR CARE AND VALUE ADDED SERVICES Vehicle Interior Enrichment Why protect your new car’s fabric interior?  Someone will soil your vehicle's fabric carpet or seats.  A significant detractor from your vehicle's resale value.  A permanent stain on your vehicle's interior fabric. The enemy: Drink Spills - Food Stains - Mud - Ultraviolet Rays Pets - Traffic Benefits: Vehicle Interior Enrichment  Removal of medium stains and dirt from all interior parts of the car i.e., carpet, upholstery and roof lining.  Cleaning of windshield and all windows (inside and outside)  Dressing of all internal plastics (eg: door pad trims) and rubber parts.  The treatment involves cleaning and dressing of all parts of the exposed interiors.  Specialised protection for seat fabric from liquid spills. TATA MOTORS has tied up with M/s Wurth and M/s Autokrom for this world class treatment at affordable prices. This treatment is available in all authorized workshops. The Dealer Service Marketing Executive will explain to you the benefits and terms and conditions of this treatment.

I / We have been explained the Terms and conditions, Coverage and Owner’s responsibility by the Dealer Service Marketing Executive. I wish to avail / Do not wish to avail extended warrant policy.

Customer’s Signature Dealer’s Signature

187 CAR CARE AND VALUE ADDED SERVICES

188 WARRANTY - TERMS AND CONDITIONS We WARRANT each TATA TIGOR vehicle and parts thereof our judgment which shall be final and binding, to affect its manufactured by us to be free from defect in material and reliability, nor shall it apply if, in our opinion which shall be workmanship subject to the following terms and conditions: final and binding, the car is subjected to misuse, negli- gence, improper or inadequate maintenance or accident or 1. This warranty shall be for a period of 24 months from the loading in excess of such carrying capacity as certified by date of sale of the car or a mileage of 75,000 Kms which- us, or such services as prescribed in our Owner's Manual ever occurs earlier. are not carried out by the buyer through our sales or service 2. Our obligation under this warranty shall be limited to repair- establishments, our authorized dealers, service centres or ing or replacing, free of charge, such parts of the car which, service points. in our opinion, are defective, on the car being brought to us or to our dealers within the period. The parts so repaired or 6. This warranty shall not apply to the replacement of nor- mal wear parts, including without limitation, spark replaced shall also be warranted for quality and workman- plugs, drive belts, hoses, wiper blades, fuses, clutch ship but such warranty shall be co-terminus with this origi- disc, brake shoes, brake pads, cables and all rubber nal warranty. parts (except oil seal and glass run). 3. Any part which is found to be defective and is replaced by 7. This warranty shall not cover any inherent normal deterio- us under the warranty shall be our property. ration of the car or any of its parts arising from the actual 4. As for such parts as Tyres, Batteries, Audio and / or Video use of the car or any damage due to negligent or improper equipment (if any), etc. not manufactured by us but sup- operation or storage of the car. plied by other parties, this warranty shall not apply, but buy- 8. This warranty shall not apply to normal maintenance ser- ers of the car shall be entitled to, so far as permissible by vices like oils & fluid changes, head lamps focusing, fas- law, all such rights as we may have against such parties tener retightening, wheel balancing and alignment, tyre ro- under their warranties in respect of such parts. tation, adjustment of valve clearance, fuel timing, ignition 5. This warranty shall not apply if the car or any part thereof timing and consumables like bulbs, fuel, air & oil filters and is repaired or altered otherwise than in accordance with our gas leaks in case of air conditioned cars. standard repair procedure or by any person other than from 9. This warranty shall not apply to any damage or deteriora- our sales or service establishments, our authorized deal- tion caused by environmental pollution or bird droppings. ers, service centres or service points in any way so as, in Slight irregularities not recognized as affecting the function

189 WARRANTY - TERMS AND CONDITIONS or quality of the vehicle or parts, such as slight noise or vi- 14. This warranty is fully transferable to subsequent vehi- bration, defects appearing only under particular or irregular cle owner. Only unexpired remaining period of war- operations are items considered characteristics of the ve- ranty applies. hicle. 15. We reserve our rights to make any change or modification 10. This warranty shall be null and void if the car is subjected in design of the car or its parts or to introduce any improve- to abnormal use such as rallying, racing or participation in ment therein or to incorporate in the car any additional part any other competitive sport. This warranty shall not apply or accessory at any time without incurring any obligation to to any repair or replacements as a result of accident or col- incorporate the same in the cars previously sold. lision.

11. This warranty is expressly in lieu of all warranties, whether by law or otherwise, expressed or implied, and all other ob- ligations or liabilities on our part and we neither assume,

nor authorize any person to assume on our behalf, any other liability arising from the sale of the car or any agree- ment in relation thereto. 12. The buyer shall have no other rights except those set out above and have, in particular, no right to repudiate the sale, or any agreement or to claim any reduction in the purchase price of the car, or to demand any damages or compensa- tion for losses, incidental or indirect, or inconvenience or consequential damages, loss of car, or loss of time, or oth- erwise, incurred or accrued. 13. Any claim arising from this warranty shall be recognized only if it is notified in writing to us or to our authorized dealer without any delay soon after such defects as cov- ered & ascertained under this warranty.

190 ENVIRONMENT SAFETY TATA MOTORS LTD. is committed to produce vehicles using en-  Shift to higher gears as soon as it is possible. Use each gear vironmentally sustainable technology. A number of features up to 2/3rd of its maximum engine speed. have been incorporated in TATA MOTORS passenger vehicles  A chart indicating gear shifting speeds is given in this book. which have been designed to ensure environmental compati- bility throughout the life cycle of the vehicle. We would like to Maintenance inform you that your vehicle meets emission norms and this is  Ensure that recommended maintenance is carried out on being regularly validated at the manufacturing stages. the vehicle regularly at the Authorised Service Outlets. As a user you too can protect the environment by operating  As soon as you see any leakages of oil or fuel in the vehicle your vehicle in a proactive manner. A lot depends on your driv- we recommend to get it attended immediately. ing style and the way you maintain your vehicle. We have given  Use only recommended grades and specified quantity of a few tips for your guidance. lubricants.  Get your vehicle checked for emission periodically by an au- Driving thorised dealer.  Ensure that fuel filter, oil filter and breather are checked Avoid frequent and violent acceleration.  periodically and replaced, if required, as recommended by Do not carry any unnecessary weight in the vehicle as it  TATA MOTORS. overloads the engine. Avoid using devices requiring high  Do not pour used oils or coolants into the sewage drains, power consumption during slow city traffic condition. garden soil or open streams. Dispose the used filters and Monitor the vehicle’s fuel consumption regularly and if  batteries in compliance with the current legislation. showing rising trend get the car immediately attended at  Do not allow unauthorized person to tamper with engine the Company’s Authorised Service Outlets. settings or to carry modifications on the vehicle. Switch off the engine during long stops at traffic jams or   Never allow the vehicle to run out of fuel. signals. If you need to keep the engine running, avoid un-  Parts like brake liners, clutch discs should be vacuum necessary revving it up or stopping and starting. cleaned. Do not use compressed air for cleaning these It is not necessary to rev up the engine before turning it off  parts which may spread dust in the atmosphere. as it unnecessarily burns the fuel.

191 ENVIRONMENT SAFETY While carrying out servicing or repairs of your vehicle, you should pay keen attention to some of the important engine aggregates and wiring harness which greatly affect emis- sion. These components are: 1. Fuel injection equipment’s - pump, rail, injectors, nozzles and high pressure pipes. 2. Air Intake & Exhaust system, especially for leakages. 3. Cylinder head for valve leakage. 4. All filters such as air, oil and fuel filters (check periodi- cally). 5. Turbocharger. 6. Electrical connections. 7. If the ‘Service’ lamp continuously glows, please take the vehicle to a TATA MOTORS authorized service outlet. 8. Catalytic Converter. 9. EMS wiring harness i.e. electrical connections to all sen- sors and actuators. This Owner’s manual contains further information on driving precautions and maintenance care leading to environment protection. Please familiarize yourself with these aspects be- fore driving.

192