PACER GLASS CLAMP
FITTING INSTRUCTIONS - NOTICE DE POSE - MONTAGE HANDLEIDING - MONTAGEANLEITUNG ISTRUZIONI DI MONTAGGIO - INSTUCCIONES DE MONTAJE
Tools Required
Posidrive screwdriver Allen key 5mm
Tape measure
Torque wrench and 5mm bit 18 and 13mm spanners Spirit Level Drill
Contents of Kit
Strap bolt Wheel carriage x 2 Clip stop x 2 adaptor x 2
Glass clamp x 2 (Type dependent upon weight capacity)
Top lock nut x 2Locking plate x 2 Floor guide x 1
1 Fitting clamps (c) 2 Assemble hanger components 0mm
Gaskets Wheel carriage
(a) Unscrew to loosen clamp Glass
30Nm (d) 50 MIN Top lock nut
Locking plate (b) Clean glass (c) Set clamp to glass (d) Finger tighten ALL screws Strap bolt Torque outer then inner screws adaptor 3 Hang glass door
(a) Insert hanger assembly (b) Insert clip stop (c) Check orientation of hanger assembly in the track (d) Slide hanger assembly into the clamp (e) Final locate - hang glass panel
(a) (a)
(b) (b) IMPORTANT Please note orientation of hanger assembly
(c) Direction of (c) hanger assembly
(d) (d)
(d) Slide hanger assembly into the clamp channel (e) Allow glass panel to hang by locating the tabs on the lock plate into the cut-outs in the clamp
Location tabs 4 Height adjustment - Adjust strap bolt to set door height
Lock
Adjust height Ensure glass panel is level - hangers evenly adjusted NB - minimum/maximum adjustment = 16 -24mm see diagram 6
5 Set Floor Guide
(a) Set floor guide for glass door thickness, 8, 10 or12mm (a) (b) Position floor guide (c) Check level of panel with spirit level (d) Mark position of guide (e) Check proposed travel of door (when fully open the door is still in the guide) (f) Re-position glass door (g) Secure guide with screws (h) Slide panel back into floor guide (i) Secure retaining clip stop
(i)
Tighten screws
Ensure correct tension adjustment
SOFT FIRM (c)
(e)(f)(g)(h)
(d) (b) 6 Pacer fascia Pacer double fascia Pacer fixed panel
54 54 54 Fixed glass profile 109-121 109-121 109-121 Fascia 14-26 Fascia 14-26 14-26 600FP F160X F160X 41 41 41 Fascia F160 Fascia F160X
28
H H H
H-80 H-125 H-125 H-125
Channel 94X
Guide 8-12/SN 23
Pacer fixed panel Pacer double Pacer bracket fascia bracket combination Face fix bracket 1B Fascia F200
30 30
54 54 54 Fixed glass profile 109-121 14-26 109-121 14-26 109-121 14-26 600FP
41 41 41 Fascia F160X Fascia F200X 28 40
H H H-80 H H-80 H-125 H-125 H-125
10 10 10
(All dimensions in mm) P C Henderson Limited, Durham Road, Bowburn, County Durham DH6 5NG, UK. Web: www.pchenderson.com UK Customer Services Department: Tel: +44 (0)191 377 7345 Fax: +44 (0)191 377 3116 Email: [email protected] Part No: 668103 Export Department: Tel: +44 (0)191 377 7346 Fax: +44 (0)191 377 0755. Email: [email protected]. February 2013 - Issue 3 For all technical queries email our Technical Department: [email protected]