Mechanical / Plumbing Symbols and Abbreviations Plumbing Steam Piping Radiation Symbols Abbreviations

Total Page：16

File Type：pdf, Size：1020Kb

GENERAL NOTES: MECHANICAL / PLUMBING SYMBOLS AND ABBREVIATIONS PLUMBING STEAM PIPING RADIATION SYMBOLS ABBREVIATIONS DUCT SYMBOLS HVAC PIPING FIRE PROTECTION SYSTEM PIPE FITTINGS VALVES TEMPERATURE CONTROL/MONITORING DRAWING NOTATIONS MEDICAL SECTIONS AND DETAILS REFRIGERATION VALVES/FITTINGS DEMOLITION GENERAL NOTES DEMOLITION PLAN NOTES: CRAWL SPACE PLAN - MECHANICAL DEMOLITION NORTH FIRST FLOOR PLAN - MECHANICAL DEMOLITION NORTH DEMOLITION LEGEND: GENERAL NOTES - HYDRONIC: GENERAL NOTES - AIR DISTRIBUTION: CRAWL SPACE PLAN - MECHANICAL PIPING NORTH PLAN NOTES: CRAWL SPACE PLAN - AIR DISTRIBUTION NORTH RENOVATION LEGEND: FIRST FLOOR PLAN - MECHANICAL NORTH ENLARGED BOILER ROOM PLAN MECHANICAL ROOM PLAN NORTH NORTH DETAIL 'C' DETAIL 'B' EXTERIOR EQUIPMENT PAD DETAIL 'A' ADJACENT TO BUILDING TERMINAL UNIT HYDRONIC COIL PIPING WITH 3-WAY VALVE FAN COIL INSTALLATION DETAIL 'D' HEATING WATER PIPING SCHEMATIC FAN COIL SCHEDULE MAKE-UP AIR UNIT SCHEDULE AIR COOLED PACKAGED CHILLER SCHEDULE GAS FIRED HOT WATER BOILER SCHEDULE PUMP SCHEDULE FAN SCHEDULE HOT WATER CONVECTOR SCHEDULE GENERAL NOTES: CRAWL SPACE PLAN - PLUMBING DEMOLITION NORTH DEMOLITION PLAN NOTES: FIRST FLOOR PLAN - PLUMBING DEMOLITION NORTH DEMOLITION LEGEND: GENERAL NOTES: PLAN NOTES: CRAWL SPACE PLAN - PLUMBING NORTH RENOVATION LEGEND: FIRST FLOOR PLAN - PLUMBING NORTH FIXTURE ROUGH-IN SCHEDULE & MOUNTING HEIGHTS DETAIL 'A' DETAIL 'B' WASTE AND VENT PIPING HOT AND COLD WATER PIPING ELECTRICAL ABBREVIATIONS LIGHT FIXTURES RACEWAYS SWITCHES FIRE ALARM SYSTEMS TYPICAL WIRING DESIGNATIONS SECURITY PANELS TECHNOLOGY ROOM CIRCUIT DESIGNATIONS RECEPTACLES AND OUTLETS TYPICAL DEVICE DESIGNATIONS COMMUNICATIONS POWER EQUIPMENT MISCELLANEOUS GENERAL NOTES: CRAWL SPACE/BASEMENT PLAN - ELECTRICAL DEMOLITION DEMOLITION PLAN NOTES: NORTH FIRST FLOOR PLAN - ELECTRICAL DEMOLITION NORTH DEMOLITION LEGEND: PLAN NOTES: FIRST FLOOR PLAN - ELECTRICAL GENERAL NOTES: NORTH FIRST FLOOR PLAN - LIGHTING NORTH RENOVATION LEGEND: CRAWL SPACE/BASEMENT PLAN - ELECTRICAL NORTH GENERAL NOTES: PLAN NOTES: RENOVATION LEGEND: RISER DIAGRAM - ELECTRICAL .

Copy Link

Recommended publications

PLUMBING PERMIT APPLICATION □ Residential □ Commercial □ New □ Alteration
CITY OF BROOKFIELD For Office Use Only: PROP. TAX ID: Inspection Services Department 2000 North Calhoun RD, Brookfield, WI 53005 PERMIT # 262-796-6683 DATE ISSUED: http://www.ci.brookfield.wi.us □ BLDG PERMIT PLUMBING PERMIT APPLICATION □ Residential □ Commercial □ New □ Alteration Street Address: ________________________________________________________________________ Suite/Unit No. ___________________ Applicant is: □ Contractor □ Homeowner Owner/Occupant Name: Phone: Contractor: _______________________________________________________________ Phone: _____________________________________ Street Address: ________________________________________________ City: ________________________ State: ______ Zip: ___________ State Credential No: Check box if E-mail: you would like your permit emailed. For Office Use Only: FIXTURE OR ITEM QTY FIXTURE QTY FIXTURE ____ Air Admittance Valve ____ Interceptor Laterals & Connections ____ Area or Deck Drain ____ Kitchen Sink ____ Back Flow Preventer ____ Laundry Tub The prices listed below are for the first 100’. Over 100’ is an additional $.48 per foot. ____ Bar Sink ____ Lavatory QTY FEE TOTAL ____ Bathtub ____ Lawn Irrigation Sanitary Bldg. Drain $59.50 ____ Beer Tap ____ Manhole / Bldg. Drain Branch ( __________linear ft.) ____ Beverage Dispenser ____ Pedicure Chair Sanitary Bldg. Sewer ( __________linear ft.) $59.50 ____ Bidet ____ Pot Sink ____ Carbonator ____ Pressure Reduce Valve Storm Drain ( __________linear ft.) $59.50 ____ Case Drain ____ Prep Sink ____ Catch Basin ____ Roof Drain Water Service
[Show full text]
Basement Finishing and Remodeling Code
BASEMENT FINISHING AND REMODELING CODE GUIDELINES Johnson County Kansas Unincorporated One of the objectives of the Johnson County Building Officials Association is to enhance construction uniformity and the adoption of common construction codes and procedures. This document is intended assist contractors and home owners in understanding the minimum code requirements for basement finish projects. It is also intended to provide guidance for obtaining permits and inspections. The information provided should not be considered a complete list of code requirements. Structural modifications, such as relocation of support columns, relocation of bearing walls, or reframing floor joists are not within the scope of this document. A registered design professional should be hired to provide review and design services for structural projects. Permit requirements may vary from city to city. Complete information is available in the codes and ordinances adopted by each City. Check with your city for complete requirements prior to obtaining a permit and before starting any work. BUILDING PERMITS AND PERMIT REQUIREMENTS Permits – A permit is required to finish or remodel a basement that involves construction of walls or installation or extension of electrical circuits, plumbing drains or vents, or ductwork. Exempt Work – Repair and maintenance work, such as, carpeting, painting, wall paper, receptacle replacement, fixture replacement (sinks, stools, lighting fixtures), vanities and cabinetry do not require a permit. Contractors – Most municipalities allow a homeowner to obtain a permit to do work in the house they own and occupy. If the homeowner is hiring a contractor to do the work, this document suggests that the contractor be required to obtain the permit.
[Show full text]
Plumbing Permit Application
CITY OF SOUTHFIELD Department of Building & Safety Engineering Plumbing Permit Application MINIMUM PERMIT FEE $90.00 (Includes $40.00 application fee) Date: ____________________________________________________ Plumbing Permit: ______________________________________ PLUMBING COMMERCIAL FEE QTY TTL Application Fee $40.00 1 40.00 Building Permit: _______________________________________ Registration If Required $15.00 Sidwell: _________________________________________________ Air Admittance Valve $15.00 Backflow Preventer: Job Address: ___________________________________________ Beverage Dispenser $15.00 Tenant: _______________________________Suite:___________ Coffee Maker $15.00 Fire Sprinkler $35.00 Owner: __________________________________________________ Lawn Sprinkler $50.00 Contractor: _____________________________________________ Miscellaneous $15.00 Source protection $35.00 Contractor Address: ___________________________________ Basement Waterproofing System $50.00 City: ___________________ State: ___________Zip: _________ Bath $15.00 Building Drain to Sewer $25.00 Contractor Phone: ____________________________________ Catch Basin/Manhole $50.00 Email: ___________________________________________________ Dishwasher $15.00 Disposal $15.00 Drinking Fountain $15.00 Floor Drain $15.00 PLUMBING RESIDENTIAL FEE QTY TTL Grease / Oil Interceptor $30.00 Application Fee $40.00 1 40.00 Hose Bibb $15.00 Registration If Required $15.00 Hot Water Supply Boilers w/Separate $35.00 Air Admittance Valve $15.00 Storage Tanks (over 52 gallons) Backflow
[Show full text]
Plumbing Identification and Damage Assessment Guide
Plumbing Identification and Damage Assessment Guide *Please note that not all systems will be represented exactly by these diagrams and photos. As a vendor, it is required that you familiar yourself with all types of existing systems to assure you and your company maintains vital and accurate information. Water System Identification To properly inspect the plumbing system, determine if the property has city water or well water. The below photos will assist you in determining what kind of water system the property has. Well Water Components City Water Components Plumbing Component Identification Plumbing components are items within the property that either provide or store water into the home or drain water from the home. The items that supply water to the home are kitchen and bathroom sinks, toilets, bathtubs, showers, interior and exterior faucets, hot water heater, water meter, and shutoff valves. Items that drain water from the home are drainage pipes and drainage traps. Exterior Water Meter Interior Water Meter Exterior Water Faucet Interior Water Faucet Plumbing Component Identification Continued… Water Meter Shut Off Valve Toilet Shut Off Valve Kitchen Faucet Bathroom Faucet Shower and Bathtub Toilet Plumbing Component Identification Continued… Plumbing Lines Plumbing Lines P- Trap P- Trap Refrigerator Ice Maker Line Basement Floor Drainage Plumbing Component Identification Continued… Conventional Water Heater Main Devices to Document: • Hot and Cold Water Supply Lines • Temp an d Pressure Relief Valve • Drain Va lve • Thermos tat • Gas Line Entry Point Tankless Water Heater Main Devices to Document: • Incoming Cold Water Line • Outgoing Hot Water Line Plumbing Assessment Determine the Type of Plumbing in the Property.
[Show full text]
PLUMBING DICTIONARY Sixth Edition
as to produce smooth threads. 2. An oil or oily preparation used as a cutting fluid espe cially a water-soluble oil (such as a mineral oil containing- a fatty oil) Cut Grooving (cut groov-ing) the process of machining away material, providing a groove into a pipe to allow for a mechani cal coupling to be installed.This process was invented by Victau - lic Corp. in 1925. Cut Grooving is designed for stanard weight- ceives or heavier wall thickness pipe. tetrafluoroethylene (tet-ra-- theseveral lower variouslyterminal, whichshaped re or decalescensecryolite (de-ca-les-cen- ming and flood consisting(cry-o-lite) of sodium-alumi earthfluo-ro-eth-yl-ene) by alternately dam a colorless, thegrooved vapors tools. from 4. anonpressure tool used by se) a decrease in temperaturea mineral nonflammable gas used in mak- metalworkers to shape material thatnum occurs fluoride. while Usedheating for soldermet- ing a stream. See STANK. or the pressure sterilizers, and - spannering heat resistantwrench and(span-ner acid re - conductsto a desired the form vapors. 5. a tooldirectly used al ingthrough copper a rangeand inalloys which when a mixed with phosphoric acid.- wrench)sistant plastics 1. one ofsuch various as teflon. tools to setthe theouter teeth air. of Sometimesaatmosphere circular or exhaust vent. See change in a structure occurs. Also used for soldering alumi forAbbr. tightening, T.F.E. or loosening,chiefly Brit.: orcalled band vapor, saw. steam,6. a tool used to degree of hazard (de-gree stench trap (stench trap) num bronze when mixed with nutsthermal and bolts.expansion 2. (water) straightenLOCAL VENT.
[Show full text]
SOHO Design in the Near Future
Rochester Institute of Technology RIT Scholar Works Theses 12-2005 SOHO design in the near future SooJung Lee Follow this and additional works at: https://scholarworks.rit.edu/theses Recommended Citation Lee, SooJung, "SOHO design in the near future" (2005). Thesis. Rochester Institute of Technology. Accessed from This Thesis is brought to you for free and open access by RIT Scholar Works. It has been accepted for inclusion in Theses by an authorized administrator of RIT Scholar Works. For more information, please contact [email protected]. Rochester Institute of Technology A thesis Submitted to the Faculty of The College of Imaging Arts and Sciences In Candidacy for the Degree of Master of Fine Arts SOHO Design in the near future By SooJung Lee Dec. 2005 Approvals Chief Advisor: David Morgan David Morgan Date Associate Advisor: Nancy Chwiecko Nancy Chwiecko Date S z/ -tJ.b Associate Advisor: Stan Rickel Stan Rickel School Chairperson: Patti Lachance Patti Lachance Date 3 -..,2,2' Ob I, SooJung Lee, hereby grant permission to the Wallace Memorial Library of RIT to reproduce my thesis in whole or in part. Any reproduction will not be for commercial use or profit. Signature SooJung Lee Date __3....:....V_6-'-/_o_6 ____ _ Special thanks to Prof. David Morgan, Prof. Stan Rickel and Prof. Nancy Chwiecko - my amazing professors who always trust and encourage me sincerity but sometimes make me confused or surprised for leading me into better way for three years. Prof. Chan hong Min and Prof. Kwanbae Kim - who introduced me about the attractive
[Show full text]
Illinois Plumbing Code
DPH 77 ILLINOIS ADMINISTRATIVE CODE 890 SUBCHAPTER r TITLE 77: PUBLIC HEALTH CHAPTER I: DEPARTMENT OF PUBLIC HEALTH SUBCHAPTER r: WATER AND SEWAGE PART 890 ILLINOIS PLUMBING CODE SUBPART A: DEFINITIONS AND GENERAL PROVISIONS Section 890.110 Applicability 890.120 Definitions 890.130 Incorporated and Referenced Materials 890.140 Compliance with this Part 890.150 Workmanship 890.160 Used Plumbing Material, Equipment, Fixtures 890.170 Sewer and/or Water Required 890.180 Sewer and Water Pipe Installation 890.190 Piping Measurements 890.200 Operation of Plumbing Equipment SUBPART B: PLUMBING MATERIALS Section 890.210 Materials 890.220 Identification (Repealed) 890.230 Safe Pan Material and Construction SUBPART C: JOINTS AND CONNECTIONS Section 890.310 Tightness 890.320 Types of Joints 890.330 Special Joints 890.340 Use of Joints 890.350 Unions 890.360 Water Closet and Pedestal Urinal 890.370 Prohibited Joints and Connections in Drainage Systems 890.380 Increasers and Reducers SUBPART D: TRAPS AND CLEANOUT (T/C-1) DPH 77 ILLINOIS ADMINISTRATIVE CODE 890 SUBCHAPTER r Section 890.410 Fixture Traps/Continuous Waste 890.420 Pipe Cleanouts 890.430 Cleanout Equivalent 890.440 Acid-Proof Traps SUBPART E: INTERCEPTORS − SEPARATORS AND BACKWATER VALVES Section 890.510 Grease Interceptor Requirements 890.520 Gasoline, Oil and Flammable Liquids 890.530 Special Waste Interceptors 890.540 Laundries (Repealed) 890.550 Backwater Valves − Sanitary System and Storm System (Repealed) SUBPART F: PLUMBING FIXTURES Section 890.610 General Requirements − Material
[Show full text]
Above Ceiling Inspections
November 2018 Office of Education and Data Management Fall 2018 Career Development Seminar November 2018 Above Ceiling Inspections Presented by Joseph J. Summers, MCP, CBO, Senior Project Inspector, 4LEAF 2018 CT State Building Code books are available 2 OEDM- Fall 2018 Career Development 1 November 2018 Online Governmental Consensus Vote (OGCV) Cdpaccess.com Opens approximately Nov. 15-30 Your vote does count 3 Reference Code: 2018 CT State Building Code 2015 IBC 2015 IMC 2015 IPC 2017 NEC 4 OEDM- Fall 2018 Career Development 2 November 2018 Objectives: • Identify key building elements that require inspections above the ceiling. • Review codes and other standards that should be referenced during above ceiling inspection process. • Discuss inspection related issues. 5 What are we doing? • Reinspection of all the rough-ins and the grid lay-out of the ceiling • Check for approved inspections from plumbing, mechanical, electrical, fuel gas, sprinkler, framing and fire marshal if required 6 OEDM- Fall 2018 Career Development 3 November 2018 Is this a Required Inspection? • 110.3.8 Other inspections. In addition to the inspections specified in Sections 110.3.1 through 110.3.7, the building official is authorized to make or require other inspections of any construction work to ascertain compliance with the provisions of this code and other laws that are enforced by the department of building safety. 7 Access for Inspection • 110.5 Inspection requests. • It shall be the duty of the holder of the building permit or their duly authorized agent to notify the building official when work is ready for inspection. • It shall be the duty of the permit holder to provide access to and means for inspections of such work that are required by this code.
[Show full text]
Venting for Plumbing Systems
PMA ONLINE TRAINING Venting for Plumbing Systems One Hour Continuing Education © PMA of Georgia 2010 Venting PMA training disclaimer The information provided in this document is intended for use as a guideline and is not intended as, nor does it constitute, legal or professional advice. PMA does not warrant that adherence to, or compliance with, any recommendations, best practices, checklists, or guidelines will result in a particular outcome. In no event will PMA or any of its subsidiaries or affiliates be liable in tort or in contract to anyone who has access to or uses this information. PMA does not warrant that the information in this document constitutes a complete and finite list of each and every item or procedure related to the topics or issues referenced herein. Furthermore, federal, state or local laws, regulations, standards or codes may change from time to time and the reader should always refer to the most current requirements. © PMA of Georgia 2010 Venting This discussion on venting references the International Plumbing Code 2006 edition. Chapter 9 Vents And the Georgia State Amendments of 2007 © PMA of Georgia 2010 Venting The Drain Waste and Vent (DWV) system is perhaps the most important part of the total plumbing system in a building. The DWV system is for the removal of waste water and material from the building. Inspectors recognize this portion of the plumbing system as a major concern for not only the function of the plumbing but for the protection of the health of the building occupants. © PMA of Georgia 2010 Venting When people first brought the well pump into the house, they would pump water into vessels for use.
[Show full text]
RS-15- Common Residential Codes
Full Service Center East Area Service Center 827 7th Street, Room 102 5229 Hazel Avenue, Suite B Sacramento, CA 95814 Fair Oaks, CA 95628 M-F 8:30am - 4:30pm M-Tu. 9:00am - 4:00pm Building Permits & Inspection Division Bradshaw Center North Area Service Center 9700 Goethe Road, Suite A 3331 Peacekeeper Wy, Suite 100 General Information: (916) 875-5296 Sacramento, CA 95827 McClellan, CA 95652 www.building.saccounty.net M-F 8:30am - 4:30pm W-Th. 9:00am - 4:00pm COMMON RESIDENTIAL CODES Project Description Date Case No. These sheets, when attached to a set of plans, become part of those plans and must remain attached thereto. The approval of this plan and the specifications shall not be held to permit or approve the violation of any County ordinance or State or Federal law. Sacramento County currently enforces the 2016 California Building Code (CBC), 2016 California Residential Code (CRC), 2016 California Mechanical Code (CMC), 2016 California Electrical Code (CEC), 2016 California Plumbing Code (CPC), 2016 California Fire Code (CFC), 2016 California Energy Commission Standards (CESC) and the current California Health and Safety Codes as well as Sacramento County locally adopted amendments to such codes. I have read and will comply with the items in this document and as marked on the plans. I am aware that the text and code sections referenced in this form may be appealed as per SCC 105. Date Signature of: Owner Authorized Agent Contractor Architect/Engineer BUILDING CODE REQUIREMENTS Section R301 Design Criteria B-1 R301.1.1 Alternative provisions. Conventional Light-Frame Construction complying with the AF&PA (WFCM) is an acceptable alternative to this CRC provision, when addressing prescriptive framing requirements.
[Show full text]
CHAPTER 5 Building, Electrical, Mechanical and Plumbing Code
CHAPTER 5 Building, Electrical, Mechanical and Plumbing Code DIVISION I Adoption and Administration Sec. 5.100 Title and Adoption ............................. ........................................................................................... 4 Sec. 5.101 Applicability .................................................................................................................................. 6 Sec. 5.102 Inspection Division …………………………………………………………………………. ....... 6 Sec. 5.103 Permits Required............................................................................................................................ 8 Sec. 5.104 Building permits not required……………………….…………………………………..…. ......... 9 Sec. 5.105 Electrical permits not required…………………………………………………………..… .......... 10 Sec. 5.106 Gas system permits not required………………….……………………………………… ............ 10 Sec. 5.107 Mechanical permits not required………………………………………………………..… .......... 10 Sec. 5.108 Plumbing permits not required…………………………………………………………..… ......... 10 Sec. 5.109 Public service agencies exempt from some permits…………………………………….. ............. 11 Sec. 5.110 Submittal Documents…………………………………………………………………....... ........... 11 Sec. 5.111 Temporary Structures…………………………………………………………………....... .......... 12 Sec. 5.112 Fees ................................................................................................................................................ 12 Sec. 5.113 Building inspections………………………………………………………………………. .......... 13 Sec. 5.114 Electrical inspections……………………………………………………………………..
[Show full text]
PL-0115-PLSPEC • Plumbing Specialities
PL-0115-PLSPEC • Plumbing Specialities Prices Effective January 5, 2015 CAST IRON QUICK-SET NO HUB CLOSET CAST BRASS CLOSET FLANGE - CHROME FLANGE AND BEND List Inner Master List Inner Master Part # Size Price Qty Qty Part # Size Price Qty Qty CLEVELAND CODE CLOSET CFCI-320 3" X 2" 11.88 1 200 62FCLV 14.51 1 50 FLANGE CFCI-420 4" X 2" 13.10 1 200 CF-100 4" FOR LEAD 14.84 1 50 CFCI-420O 4" X 2" OFFSET FLANGE 27.87 1 16 CF-200 4" X 3" DWV FOR SWEAT 24.84 1 50 CFCI-430 4" X 3" 21.64 1 200 CF-250 3" DWV SHALLOW 22.69 1 50 CFCI-440 4" X 4" 22.48 1 200 CF-300 4" DEEP SEAL 19.07 1 50 CICB1116 4" X 16" BEND 87.73 1 80 CF-400 4" X 3" FOR LEAD 24.23 1 50 CF-500 4" OFFSET 26.98 10 50 BRASS FERRULE NO HUB BACK WATER VALVE List Inner Master Part # Size Price Qty Qty List Inner Master CBF-300 3" X 3" WITHOUT BEAD 19.89 1 32 Part # Size Price Qty Qty CBF-340 3" X 4-1/2" WITHOUT BEAD 25.00 1 32 CIBWV08 2" 65.63 1 200 CBF-400 4" X 3" WITHOUT BEAD 29.50 1 32 CIBWV10 3" 104.77 1 128 CBF-400B 4" X 3" WITH BEAD 28.31 1 40 CIBWV11 4" 166.38 1 75 CBF-440 4" X 4-1/4" WITHOUT BEAD 32.15 1 32 CBF-440B 4" X 4-1/4" WITH BEAD 34.73 1 32 CAST IRON BOILER TUBE PLUGS CBF-550B 5" WITH BEAD 47.66 1 500 Part # Size List Inner Master Price Qty Qty NO HUB CAST IRON ADJUSTABLE FLOOR DRAIN BTP-150 1-1/2" 6.48 1 60 BTP-200 2" 8.66 1 50 List Inner Master Part # Size Price Qty Qty BTP-250 2-1/2" 8.66 1 30 2" WITH 4" CHROME PLATED CIFD15NH2 129.60 1 104 BTP-300 3" 9.97 1 24 BRASS STRAINER BTP-350 3-1/2" 16.76 1 16 3" WITH 4" CHROME PLATED CIFD15NH3 129.60 1 104 BTP-400 4" 21.57 1 10 BRASS STRAINER 4" WITH 4" CHROME PLATED CIFD15NH4 129.60 1 104 BRASS STRAINER www.matco-norca.com Global sourcing.
[Show full text]