TECH SUPPORT: 503.693.1918 WWW.STELLARALARMS.COM USER GUIDE AND INSTALLATION MANUAL RS1050 - REMOTE START ADD-ON

RS1050 Engine Start + Turbo Timer Module ByPass Output (RED/BLACK) Owner’s & Installer’s Manual This wire is designed for bypassing the external device when the engine is started by the SYSTEM FEATURES RS1050. a • Tach or Tachless Start(Alternator) .Bypass Output (RED/BLACK) will send the • Smart RPM Learning Adjustor solid negative signal during the engine start or • Optional +/- Glow Plug Input turbo timer mode. • Turbo Timer b.The solid negative signal will halt when the • Timer Start engine start or turbo timer mode is stopped. • Programmable Engine Running Time • Programmable Cranking Time Glow Plug • Bypass Output (wait-to-start inputs, -GREEN/WHITE or • Safety Wire +PURPLE/WHITE) • Compatible with Auto or Manual Transmission These wires are designed for a diesel engine. • Anti-grind Select negative or positive depending on your needs. OPERATION a.For the car equipped with diesel engine, this Starting & Stopping the Engine: wire must be connected to the wait-to-start light a. Feed Activation Input (PINK) with three negative in the dashboard. Connect negative pulses within 5 seconds to start or stop the engine (GREEN/WHITE) to the wait-to-start light if the running alternately. light is negative trigger or connect b. During the turbo timer mode, feeding Activation +(PURPLE/WHITE) to the light if positive trigger. Input (PINK) with two negative pulses will stop the turbo timer, and the timed start will not be started. *For the car equipped with gasoline c. During timer start mode, feeding Activation Input engine, connect one of them to the (PINK) with two negative pulses will stop the timer ground or +12v source. start, and ignition engine. Timer start will be re-started until the engine shut down Safety Wire-Hood Pin(BLUE) d. During a timed start and with the engine running, a.Connect this wire to the hood pin switch. The feeding Activation Input (PINK) with two negative switch must provide a ground output when pulses will shut down engine and timer start will switch is opened. re-start. b.The engine will stop running or not be started With the Engine Running, (or in turbo timer mode): when this wire provides a ground output.

1 Disarm the car alarm Footbrake & Handbrake(BLACK/RED) 2. Insert the car key into the ignition then switch to Connect Hand or Footbrake (BLACK/RED) to the On position. Handbrake for the car equipped with manual 3. Step on the footbrake or pull down the hand- transmission or to the footbrake for auto trans- brake, then go. mission vehicle. Brake must send out 12v signal. * The engine will shut down if the footbrake is If it is a negative output, you will need to use a tapped or handbrake is pulled down before switch- relay to reverse polarity. ing the ignition on.

RS1050 - Revised 12/27/2013 - Page 1 of 3 Rev 7 ©2013 Hoffman Automotive Accessories L.L.C. All Rights Reserved. All other trademarks are the property of their respective owners. 1. TECH SUPPORT: 503.693.1918 WWW.STELLARALARMS.COM USER GUIDE AND INSTALLATION MANUAL RS1050 - REMOTE START ADD-ON a.Turn off all the devices such as Stereo, OPTIONAL FEATURES Radio, and air condition...etc. ByPass Output (RED/BLACK) b.Shift the gear to neutral or parking This wire is designed for bypassing the external 1 2 3 4 Number Feature position(and pull up the handbrake if device when the engine is started by the Flash Flashes Flashes Flashes Engine Sense Alternator Tachometer connected). RS1050. 1 Mode c.Switch the ignition on, start the engine and a.Bypass Output (RED/BLACK) will send the Cranking release the footbrake until idling. solid negative signal during the engine start or 2 600ms 800ms 1000ms Time d.Press and hold the valet switch for 2 sec. turbo timer mode. when the tachometer is about 800rpm and the b.The solid negative signal will halt when the Engine Run 3 10 min. 20 min. 30 min. LED is on. engine start or turbo timer mode is stopped. Time e.Release the valet switch when the parking Turbo Timer 4 Disable 2 min. 3 min. lights turn on to confirm the RPM learning is Glow Plug Timer Start completed. (wait-to-start inputs, -GREEN/WHITE or 5 4 Hour 8 Hour 12 Hour 24 Hour *if the LED is still off when the tachometer is +PURPLE/WHITE) about 800rpm then turn the RPM adjust knob These wires are designed for a diesel engine. Program the Optional Features until the LED is just on. Select negative or positive depending on your Follow the steps below to program the optional features: needs. #2 Cranking Time a.For the car equipped with diesel engine, this a.Turn the ignition on then off with RS1050 deactivated. Default: 600ms wire must be connected to the wait-to-start light b.Within 10 sec., press the valet switch on-off-on-off-on-off. If the engine doesn’t start smoothly, then set in the dashboard. Connect negative c.Then, parking lights will be on for 1 sec. to confirm the the crank time longer. (GREEN/WHITE) to the wait-to-start light if the module has been in programming mode. light is negative trigger or connect d.Within 10 sec., press the valet switch #1 ~ #5 times to #3 Engine Running Time +(PURPLE/WHITE) to the light if positive trigger. select the items. Default: 10 minutes e The engine will run for 10, 20 or 30 minutes *For the car equipped with gasoline .The parking lights will flash the same number of times as as programmed and then shut down automati- engine, connect one of them to the the item being selected to confirm the selection. g.Then, press and hold the valet switch and the parking cally ground or +12v source. lights will flash 1 ~ 4 times as per the optional features.

h #4 Turbo Timer Safety Wire-Hood Pin(BLUE) .Release the valet switch when the parking lights flashed the times as the desired feature. Default: Disable a.Connect this wire to the hood pin switch. The i.Press the valet switch to select #1 ~ #5 times to select the The turbo timer will not be activated. switch must provide a ground output when next items for programming. When: 2 or 3 minutes switch is opened. *During the programming mode, if the valet is not pressed a.The engine will be delayed 2 or 3 minutes b.The engine will stop running or not be started within 10 sec. or turn the ignition on then the system will to shut down as programmed. when this wire provides a ground output. leave the programming mode and the parking lights flash b.The operation is as follows:

once to confirm. -Keep the engine running Footbrake & Handbrake(BLACK/RED) -Pull up the handbrake(or release the foot- Connect Hand or Footbrake (BLACK/RED) to the brake) Handbrake for the car equipped with manual EXPLANATION OF OPTIONAL FEATURES -Switch the ignition off, the ACC. and ignition transmission or to the footbrake for auto trans- #1 Engine Sense Mode. will keep on running for 2 or 3 minutes as mission vehicle. Brake must send out 12v signal. Default: Alternator(auto-detection and no need to wire programmed, then shut down automatically If it is a negative output, you will need to use a Tach(GREEN). *The turbo timer would be functional only relay to reverse polarity. When: Tach when the engine has been running for at least Connect W2-6 to the ignition coil(-) and the RPM learning 10 sec. has to be done as follows before initial operation: c.The turbo timer mode will be interrupted

RS1050 - Revised 12/27/2013 - Page 2 of 3 Rev 7 ©2013 Hoffman Automotive Accessories L.L.C. All Rights Reserved. All other trademarks are the property of their respective owners. 2. TECH SUPPORT: 503.693.1918 WWW.STELLARALARMS.COM USER GUIDE AND INSTALLATION MANUAL RS1050 - REMOTE START ADD-ON when any one of the following have happened: -The wire HoodPin (BLUE) shows a negative input. -The wire Hand or Foot Brake (BLCK/RED) shows +12V. -The wire Activation Input (PINK) shows a negative pulse.

#5 Timer Start Default: 4 hour The engine will start automatically per 4 hour When: 12 or 24 hour The engine will start automatically per 12 or 24 hour as programmed. The clocking(4, 12 or 24 hours) of timer start has to be turned on as follows before initial operation -Switch the ignition on then off. -Press and hold the valet switch and release after the parking lights flash twice to confirm the timer start feature is turned on and the system starts to count time(4, 12 or 24 as programmed). *Repeat above steps to turn on the timer start feature if the footbrake has been tapped or handbrake has been pull down with the engine running.

WIRING DIAGRAM

*For the car equipped Built-in Relay Built-in Relay with gasoline engine, connect one of them to RS1050 Unit the ground or +12v Built-in Relay source.

Input Sensitivity/ + Wait to Start (diesel) RPM Adjustment Knob

Valet Switch

Neg. Trigger Activation Input (PINK) Starter ByPass Output (RED/BLACK) (YELLOW/GREEN)

Positive Wait-to-Start (diesel) (PURPLE/WHITE) 12v (RED) Ground (GREEN/WHITE) Ignition (RED/BLACK) Hand or Foot Brake (BLACK/RED) Hood Pin (BLUE) Acc. (BLUE/WHITE) Tachometer (GREEN) Starter Kill (ORANGE) Ground (BLACK) Parking Lights (WHITE) Acc Ign Keyless Start Alarm Brake System Ignition 2 (RED/WHITE) Acc.2 (BLUE/BLACK) Starter ✂ + Cut Hood Pin 87 + *NOTE: wire per instructions 86 87a 85 30

Tach

87 12V 87 12V Bypass 87a 85 87a 85 For vehicles that require ACC 2 IGN 2, 86 86 30 30 converting to 12V may be necessary. IGN 2 Output ACC 2 output Consult your manufacturer, as incorrect installation may void warranty. Not Included

RS1050 - Revised 12/27/2013 - Page 3 of 3 Rev 7 ©2013 Hoffman Automotive Accessories L.L.C. All Rights Reserved. All other trademarks are the property of their respective owners. 3.