Management – Deck

Total Page:16

File Type:pdf, Size:1020Kb

Management – Deck MANAGEMENT – DECK REPUBLIC OF THE PHILIPPINES DEPARTMENT OF TRANSPORTATION MARITIME INDUSTRY AUTHORITY STCW OFFICE GUIDE QUESTIONNAIRES for seafarers The Annual Publication of Database of Questionnaires is mandated in Republic Act 10635 or the Act Establishing the Maritime Industry Authority (MARINA) as the Single Maritime Administration Responsible for the Implementation and Enforcement of the 1978 International Convention on Standards of Training, Certification and Watchkeeping for Seafarers, 1978, as amended and International Agreements or Covenants related thereto and its Implementing Rules and Regulations. These sample questions have been reviewed and validated by our respective Board of Examiners which may serve as a guide for the review of aspiring Marine Deck and Engineering Officers, towards the successful completion of the Theoretical Examination. The following sample questions do not reflect the actual set of database of questions given during the theoretical examination. Examinees are encouraged to study the contained sample questions and probable answers as they are intended to give an indication of the format and difficulty level of the theoretical examination. You may access these guide questionnaires with your smart gadgets anywhere and anytime at your convenience. Please consider the environment before printing. Thank you. A Publication of the MARINA STCW Office MANAGEMENT – DECK FUNCTION 1 – Competence 3 1. How many points are there in a compass card? 2. What are the only magnetic compass correctors that correct for both permanent and induced effects of magnetism? 3. A relative bearing is always measured from __________. 4. A sidereal day is shorter than a solar day. This difference is due to _______. 5. A single vertical magnet placed underneath the compass in the binnacle is used to compensate for __________. 6. A system of reservoirs and connecting tubes in a gyro compass is called a __________. 7. A vessel heading NNW is on a course of __________. 8. A vessel is heading magnetic northwest and its magnetic compass reads a heading of 318 deg. What action should be taken to remove this error dutring compass adjustment? 9. As a vessel changes course to starboard, the compass card in a magnetic compass __________. 10. At the magnetic equator there is no induced magnetism in the vertical soft iron because __________. 11. At the master gyrocompass, the compass card is attached to the __________. 12. Before a magnetic compass is adjusted certain correctors must be checked to ensure that they are free of permanent magnetism. These correctors are the __________. 13. Besides variation, what does the compass rose on a nautical chart also indicates? 14. Compass deviation is caused by __________. MANAGEMENT – DECK 15. Compass error is equal to the __________. 16. Deviation changes with a change in __________. 17. Deviation is the angle between the __________. 18. Deviation which is maximum on intercardinal compass headings may be removed by the __________. 19. Every field of magnet contains something which is called _______. 20. Gyrocompass repeaters reproduce the indications of the master gyrocompass. They are __________. 21. Heeling error is defined as the change of deviation for a heel of __________. 22. How is the annual rate of change for magnetic variation shown on a pilot chart? 23. How many degrees are there on a compass card? 24. If a magnetic compass is not affected by any magnetic field other than the Earths, which statement is TRUE? 25. If a ship is proceeding towards the magnetic equator, the uncorrected deviation due to permanent magnetism __________. 26. If the compass heading and the magnetic heading are the same then __________. 27. If the gyrocompass error is east, what describes the error and the correction to be made to gyrocompass headings to obtain true headings? 28. If the magnetic heading is greater than the compass heading, the deviation is __________. 29. Indications of the master gyrocompass are sent to remote repeaters by the _______ 30. Isogonic lines are lines on a chart and what does it indicates? MANAGEMENT – DECK 31. It is a coefficient used to identify the semicircular deviation which is proportional to the cosine of the compass heading? 32. It is a semi circular deviation which is proportional to the cosine twice of the compass heading. 33. Magnetic compass deviation __________. 34. Magnetic heading differs from compass heading by __________. 35. Magnetic variation changes with a change in __________. 36. Magnetism which is present only when the material is under the influence of an external field is called __________. 37. Magnets are placed in horizontal trays in the compass binnacle to compensate for the __________. 38. On an isomagnetic chart, what is the line of zero variation? 39. Permanent magnetism is caused by __________. 40. Quadrantal error in a gyrocompass has its GREATEST effect __________. 41. The compass deviation changes as the vessel changes __________. 42. The compass heading of a vessel differs from the true heading by __________. 43. The compass rose on a nautical chart indicates both variation and __________. 44. The difference in degrees between true north and magnetic north is called __________. 45. The directive force of a gyrocompass __________. 46. The error in a magnetic compass caused by the vessel's magnetism is called _______. 47. The Flinders bar on a magnetic compass compensates for the __________. MANAGEMENT – DECK 48. The greatest directive force is exerted on the magnetic compass when the _______. 49. The gyro compass is affected by three natural errors. One of these is caused when the ship rolls and pitches wherein the gyro is subjected to athwartship and fore-and-aft acceleration, and is called _______? 50. The gyro error introduce by ship's forward motion along its tracks also known as _______. 51. The gyrocompass error resulting from your vessel's movement in OTHER than an east-west direction is called _______. 52. The heading of a vessel is indicated by what part of the compass? 53. The horizontal angle between the magnetic meridian and the north-south line of the magnetic compass is __________. 54. The line connecting the points of the earth's surface where there is no dip is the __________. 55. The lubber's line on a magnetic compass indicates __________. 56. The magnetic compass error which changes with the geographical location of your vessel is called _______ . 57. The magnetic compass magnets are acted on by the horizontal component of the Earth's total magnetic force. This magnetic force is GREATEST at the _______. 58. The most accurate method of determining gyrocompass error while underway is by __________. 59. The permanent magnetism of a vessel may change in strength due to __________. 60. The points on the earth's surface where the magnetic dip is 90° are __________. 61. The principal purpose of magnetic compass adjustment is to __________. MANAGEMENT – DECK 62. The purpose of the soft iron spheres mounted on arms on the binnacle is to compensate for __________. 63. The spin axis of a gyroscope tends to remain fixed in space in the direction in which it is started. How does this gyroscope become north seeking so that it can be used as a compass? 64. The standard magnetic compass heading differs from the true heading by __________. 65. The total magnetic effects which cause deviation of a vessels compass can be broken down into a series of components which are referred to as __________. 66. The vertical angle between the horizontal and the magnetic line of force is the __________. 67. The vertical component of the Earth's magnetic field causes induced magnetism in vertical soft iron. This changes with latitude. What corrects for this coefficient of the deviation? 68. To center a compass bowl in its binnacle, you should have the ship on an even keel, heading north or south, and adjust the screws until __________. 69. To find a magnetic compass course from a true course you must apply __________. 70. True heading differs from magnetic heading by __________. 71. Variation in a compass is caused by __________. 72. What are the only magnetic compass correctors that correct for both permanent and induced effects of magnetism? 73. What aspect where Magnetic variation changes? 74. What caused Variation in a compass? 75. What coefficient is proportional to the sine of the compass heading? 76. What do you call those Lines on a chart which connect points of equal magnetic variation? MANAGEMENT – DECK 77. What does the agonic line on an isomagnetic chart indicates? 78. What happens to the compass card in a magnetic compass when a vessel changes course to starboard? 79. What indicates in the agonic line on an isomagnetic chart? 80. What is an advantage of the magnetic compass aboard vessels? 81. What is an error in a gyrocompass caused by rapid changes in course, speed and latitude causing deviation before the gyro can adjust itself? 82. What is called as the gyrocompass error resulting from your vessels movement in OTHER than an eastwest direction? 83. What is the basic principle of the magnetic compass? 84. What is the cause of variation which affects the directive force of a magnetic compass of a ship? 85. What is the compass error of a magnetic compass that has no deviation? 86. What is the most accurate method of determining gyrocompass error while underway? 87. What lines are indicated on a chart by an Isogonic lines? 88. What lines on a chart which connect points of equal magnetic variation are called? 89. What should be done when a magnetic compass is not in use for a prolonged period of time? 90. What then if the compass heading and the magnetic heading are the same? 91. What would happen if the compass heading and the magnetic heading are the same? 92.
Recommended publications
  • Science and the Instrument-Maker
    r f ^ Science and the Instrument-maker MICHELSON, SPERRY, AND THE SPEED OF LIGHT Thomas Parke Hughes SMITHSONIAN STUDIES IN HISTORY AND TECHNOLOGY • NUMBER 37 Science and the Instrument-maker MICHELSON, SPERRY, AND THE SPEED OF LIGHT Thomas Parke Hughes Qmit/isoDian Ij;i^titution 'PJ^SS City of Washington 1976 ABSTRACT Hughes, Thomas Parke. Science and the Instrument-maker: Michelson, Sperry, and the Speed of Light. Smithsonian Studies in History and Technology, number 37, 18 pages, 9 figures, 2 tables, 1976.-This essay focuses on the cooperative efforts between A. A. Michelson, physicist, and Elmer Ambrose Sperry, inventor, to produce the instr.umentation for the determination of the speed of light. At the conclusion of experiments made in 1926, Michelson assigned the Sperry in­ struments the highest marks for accuracy. The value of the speed of light accepted by many today (299,792.5 km/sec) varies only 2.5 km/sec from that obtained using the Sperry octagonal steel mirror. The main problems of producing the instrumentation, human error in the communication of ideas to effect that in­ strumentation, a brief description of the experiments to determine the speed of light, and the analysis and evaluation of the results are discussed. OFFICIAL PUBLICATION DATE is handstamped in a limited number of initial copies and is recorded in the Institution's report, Smithsonian Year. Si PRESS NUMBER 6I41. COVER: A. A. Michelson and Elmer Ambrose Sperry. Library of Congress Cataloging in Publication Data Hughes, Thomas Parke. Science and the instrument-maker. (Smithsonian studies in histoi7 and technology ; no. 37) Supt.
    [Show full text]
  • 3D Rigid Body Dynamics: Tops and Gyroscopes
    J. Peraire, S. Widnall 16.07 Dynamics Fall 2008 Version 2.0 Lecture L30 - 3D Rigid Body Dynamics: Tops and Gyroscopes 3D Rigid Body Dynamics: Euler Equations in Euler Angles In lecture 29, we introduced the Euler angles as a framework for formulating and solving the equations for conservation of angular momentum. We applied this framework to the free-body motion of a symmetrical body whose angular momentum vector was not aligned with a principal axis. The angular moment was however constant. We now apply Euler angles and Euler’s equations to a slightly more general case, a top or gyroscope in the presence of gravity. We consider a top rotating about a fixed point O on a flat plane in the presence of gravity. Unlike our previous example of free-body motion, the angular momentum vector is not aligned with the Z axis, but precesses about the Z axis due to the applied moment. Whether we take the origin at the center of mass G or the fixed point O, the applied moment about the x axis is Mx = MgzGsinθ, where zG is the distance to the center of mass.. Initially, we shall not assume steady motion, but will develop Euler’s equations in the Euler angle variables ψ (spin), φ (precession) and θ (nutation). 1 Referring to the figure showing the Euler angles, and referring to our study of free-body motion, we have the following relationships between the angular velocities along the x, y, z axes and the time rate of change of the Euler angles. The angular velocity vectors for θ˙, φ˙ and ψ˙ are shown in the figure.
    [Show full text]
  • Chapter 7 – Autopilot Models for Course and Heading Control
    Chapter 7 – Autopilot Models for Course and Heading Control 7.1 Autopilot Models for Course Control 7.2 Autopilot Models for Heading Control Automatic pilot, “also called autopilot, or autohelmsman, device for controlling an aircraft or other vehicle without constant human intervention.” Ref. Encyclopedia Britannica The first aircraft autopilot was developed by Sperry Corporation in 1912. It permitted the aircraft to fly straight and level on a compass course without a pilot's attention, greatly reducing the pilot's workload. Elmer Ambrose Sperry, Sr. (1860–1930) Lawrence Sperry (the son of famous inventor Elmer Sperry) demonstrated it in 1914 at an aviation safety contest held in Paris. Sperry demonstrated the credibility of the invention by flying the aircraft with his hands away from the controls. He was killed in 1923 when his aircraft crashed in the English channel. In the early 1920s, the Standard Oil tanker J.A. Moffet became the first ship to use an autopilot. Ref. Wikipedia Lawrence Burst Sperry (1892—1923) 1 Lecture Notes TTK 4190 Guidance, Navigation and Control of Vehicles (T. I. Fossen) Chapter Goals • Be able to explain the differences of course and heading controlled marine craft. In what applications are they used. • Understand what the crab angle is for a marine craft: • Understand why heading control is used instead of course control during stationkeeping. • Be able to compute the COG using two waypoints • Know what kind of sensors that give you a direct measurement of SOG and COG under water and on the surface. • Understand the well-celebrated Nomoto models for heading and course control, and it is extension to nonlinear theory (maneuvering characteristics) • Be able to explain what the pivot point is.
    [Show full text]
  • Basic Instruments Introduction Instruments Mechanically Measure Physical Quantities Or Properties with Varying Degrees of Accuracy
    Chapter 3 Basic Instruments Introduction Instruments mechanically measure physical quantities or properties with varying degrees of accuracy. Much of a navigator’s work consists of applying corrections to the indications of various instruments and interpreting the results. Therefore, navigators must be familiar with the capabilities and limitations of the instruments available to them. A navigator obtains the following flight information from basic instruments: direction, altitude, temperature, airspeed, drift, and groundspeed (GS). Some of the basic instruments are discussed in this chapter. The more complex instruments that make accurate and long distance navigation possible are discussed in later chapters. 3-1 Direction The force of the magnetic field of the earth can be divided into two components: the vertical and the horizontal. The Basic Instruments relative intensity of these two components varies over the The navigator must have a fundamental background in earth so that, at the magnetic poles, the vertical component navigation to ensure accurate positioning of the aircraft. Dead is at maximum strength and the horizontal component is reckoning (DR) procedures aided by basic instruments give minimum strength. At approximately the midpoint between the navigator the tools to solve the three basic problems of the poles, the horizontal component is at maximum strength navigation: position of the aircraft, direction to destination, and the vertical component is at minimum strength. Only and time of arrival. Using only a basic instrument, such as the the horizontal component is used as a directive force for a compass and drift information, you can navigate directly to magnetic compass. Therefore, a magnetic compass loses its any place in the world.
    [Show full text]
  • GYROCOMPASS CMZ 900 Series
    GYROCOMPASS CMZ 900 series Bulletin 80B10M09E 2nd Edition CMZ 900 GYROCOMPASS is highly reliable and long life. CONTROL BOX (MKC 326/327) MASTER COMPASS (MKM 026) A gyrocompass detects the true north by means of a fast-spinning rotor, which is suspended with no friction and is influenced by gravity and rotation of the Earth. A gyrocompass consequently indicates a ship's heading. CMZ 900 series has been type approved in accordance with International Maritime Organization (IMO) standards, resolution A.424(XI) as well as JIS-F9602, class A standards. FEATURES -A modular design saves the space. MASTER COMPASS can be integrated in the autopilot steering stand. -Manual and automatic speed error correction -External heading sensor can back up the heading outputs. -Serial data output IEC 61162-2 (high-speed transmission) -An unique anti-vibration mechanism enhanced by the velocity damping effect of high viscous oil, provides superior damping of vibration and decoupling of shock at sea. -A small and lightweight container enhances the follow up speed. The gyrocompass reading changes smoothly and does not lag when a small ship rapidly changes course. -Easy maintenance and long maintenance periods Titanium capsule and electrodes are employed for GYROSPHERE. Purity is maintained inside of the container, and maintenance interval is then longer-dated. The container is divided into two pieces at bottom when overhauled. Ship's crew can replace GYROSPHERE in case of emergency. Easy maintenance Titanium capsule PERFORMANCE and electrodes SPECIFICATIONS (lower hemisphere) -Accuracy: Static:±0.25° x sec Lat. Dynamic:±0.75° x sec Lat. -Settling time:Within 5 hours -Follow up accuracy:0.1° or less -Max.
    [Show full text]
  • Article, the Extravagantly Named German Scien- at Different Constant Velocities
    PaRT I: gyRoScoPES aNd aLBERT EINSTEIN FRoM ThE IoN hISToRIaN, MaRvIN May Elmer A. Sperry and the Gyrocompass His company became Unisys, the giant computer and informa- tion technology company, and his gyroscope-guided autopilot became known as “metal Mike,” the mechanical helmsman. lmer Ambrose Sperry was born a year accepted at that time. Although unable to Ebefore the Civil War began, but the gyro- demonstrate an actual north-pointing gyro- compasses, inertial navigators and voyage compass using his string-propelled gyroscope managements systems that stem from his (electric motors being unavailable at the innovations still steer our ships and aircraft. time), Foucault did establish the theoretical Indeed, few pioneers of navigation have left basis for the gyrocompass. as enduring a legacy. By the late 19th century, iron ships had In 1880, the 20-year-old New Yorker largely replaced wooden ships, jeopardizing Elmer Sperry at age 27 formed his first company. By 1986, Sperry the integrity of the magnetic compass, which Corporation, a merger of all eight companies for 400 years had been the navigator’s most compass was an ingenious notion, several he founded to manufacture and market his reliable course indicator. problems presented themselves to Sperry and many inventions, had become Unisys, the The age of electrification began around others who were working on the same idea. giant information technology firm. the same time, when scientists such as Max- A 1912 publication of U.S. Naval Proceedings The brilliant inventor, engineer, and well, Faraday, Helmholz, Einstein, Steinmetz, outlines these challenges: entrepreneur held 135 patents and became and Edison advanced the theoretical and 1.
    [Show full text]
  • PR-2000Series
    DIMENSIONS ■ Rudder angle indicator(for JG ships) 150 106 130 4-φ8HOLES 90 142 Autopilot 70 10 70 10 106 134 160 140 4-φ4.5HOLES - Series 4-φ6.5HOLES PR 2000 250 134 13 134 124 110 ■ Repeat back unit(for 35~45゚) ■ Repeat back unit(for 60~70゚) 140° φ8.2HOLE φ 32 32 8.2HOLE 90° 4-φ12HOLES 4-φ12HOLES 100~400 100~400 114 80 80 171 171 45.5 20 284 20 20 284 45.5 324 80 324 13 32 80 13 5.6 240 5.6 256 240 15 35 15 Design and specifications are subject to change without prior notice, and without any obligation on the part of the manufacturer. Before operating this equipment, CAUTION you should first throughly read the operator's manual. www.tokyo-keiki.co.jp/marine/e/ Marine Systems Company Head Office 2-16-46, Minami-Kamata, Ohta-ku, Tokyo 144-8551 JAPAN Tel. +81-3-3737-8611 Fax. +81-3-3737-8663 TOKYO KEIKI (SHANGHAI) CO., LTD. C-1407, Orient International Plaza. No.85 Lou Shan Guan Rd., Shanghai 200336. CHINA Tel. +86-21-3223-1252 Fax. +86-21-6278-7667 TOKYO KEIKI U.S.A., INC. 625 Fair Oaks Ave, Suite190, South Pasadena, California 91030 U.S.A. Tel. +1-626-403-1500 Fax. +1-626-403-7400 Busan Liaison Office Shindonga bldg. Room 1003, 749-1 Gayadaero, Busanjin-gu, Busan 614-783, KOREA Tel. +82-51-802-2190 Fax. +82-51-802-2188 Singapore Branch No.2 Jalan Rajah #07-26/28, Golden Wall Flatted Factory, Singapore 329134 Tel.
    [Show full text]
  • Care and Feeding of Autopilots
    BOATKEEPER Care and Feeding of Autopilots From Pacific Fishing, December 1998 By Terry Johnson, University of Alaska Sea Grant, Marine Advisory Program 4014 Lake Street, Suite 201B, Homer, AK 99603, (907) 235-5643, email: [email protected] ny device that simplifies matters for work on either a wet card or fluxgate com- cal, and the whole thing must be mounted Athe vessel operator must itself be com- pass, both of which respond to the earth’s where it is out of the weather and out of the plex; so it is with autopilots. magnetic field. Naturally, they also respond way but still has correct angle and rigidity In concept, the modern autopilot is to any other magnetic field in the boat, in- to impart full torque on the steering gear. If pretty simple. A compass indicates the cluding the engine block and electrical cir- the salesman doesn’t know exactly how to boat’s actual heading, a control unit accepts cuitry. Also, they are greatly affected by calculate sprocket size and other factors, get the heading the operator wants, a micropro- motion, including rolling, pitching, and an engineer to help you work it out. Big cessor calculates the difference between the pounding. To minimize motion the compass problems result from improper sizing. On desired and actual headings, and a power must be mounted low in the boat, prefer- hydraulic units, you need to know the ram unit acts on instructions from the control ably at the waterline and slightly forward size on your steering gear to select the cor- unit to move the rudder and turn the boat of amidships, close to the centerline.
    [Show full text]
  • NOTES and DISCUSSIONS Using a Gyroscope to Find True North—A
    NOTES AND DISCUSSIONS Using a gyroscope to find true north—A lecture demonstration Wolfgang Ruecknera) Harvard University Science Center, Cambridge, Massachusetts 02138 (Received 26 August 2016; accepted 9 December 2016) [http://dx.doi.org/10.1119/1.4973118] I. INTRODUCTION However, its behavior can be explained using physics con- cepts that are quite accessible to first year physics students. The curious behavior of a gyroscope never ceases to fasci- A description and mathematical analysis of a gyrocompass nate. It is the quintessential lecture demonstration whenever has been presented in a few papers appearing in this jour- examples of angular momentum are discussed. The gyro- nal6–9 and will not be repeated here. For example, Knudsen8 compass is but one example of its application. With conser- designed a gyrocompass for use in undergraduate instruc- vation of angular momentum in mind, most students tional physics labs, but it is quite complicated and not at all probably imagine a gyrocompass as simply a “directional” appropriate for classroom use. The purpose of this lecture gyroscope in the sense that a gyroscope (spinning freely in a demonstration is to show, in a direct and simple way, the gimbal mount) maintains its axis orientation regardless of remarkable behavior of this device. how it is moved around. They would probably be surprised to learn that if you constrain the rotational axis of a gyro- II. HOW A SIMPLE GYROCOMPASS WORKS scope to move in a horizontal plane, the axis will align itself with Earth’s meridian in a north-south
    [Show full text]
  • Chapter 420 Navigation Systems Equipment and Aids
    S9086-NZ-STM-010/CH-420R1 REVISION 1 NAVAL SHIPS’ TECHNICAL MANUAL CHAPTER 420 NAVIGATION SYSTEMS, EQUIPMENT AND AIDS THIS CHAPTER SUPERSEDES CHAPTER 420 DATED 1 JUNE 1994 DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE, DISTRIBUTION IS UNLIMITED. PUBLISHED BY DIRECTION OF COMMANDER, NAVAL SEA SYSTEMS COMMAND. 1 SEP 1999 TITLE-1 @@FIpgtype@@TITLE@@!FIpgtype@@ S9086-NZ-STM-010/CH-420R1 Certification Sheet TITLE-2 S9086-NZ-STM-010/CH-420R1 TABLE OF CONTENTS Chapter/Paragraph Page 420 NAVIGATION SYSTEMS, EQUIPMENT AND AIDS ................ 420-1 SECTION 1. NAVIGATION SYSTEM, GENERAL REQUIREMENTS ............. 420-1 420-1.1 ORGANIZATION ..................................... 420-1 420-1.1.1 CHAPTER ORGANIZATION. .......................... 420-1 420-1.1.2 ESWBS SECTIONS. ............................... 420-1 420-1.1.3 REFERENCES. .................................. 420-1 420-1.1.3.1 Naval Ships’ Technical Manuals (NSTM). ............ 420-1 420-1.1.4 BULLETINS. ................................... 420-1 420-1.2 ADMINISTRATION INFORMATION .......................... 420-2 420-1.2.1 INTENT. ...................................... 420-2 420-1.2.2 RESPONSIBILITY ASSIGNMENTS. ...................... 420-2 420-1.2.3 TRAINING. .................................... 420-2 420-1.2.4 QUALIFIED REPAIR PERSONNEL. ...................... 420-2 420-1.2.4.1 Maintenance Responsibility. .................... 420-2 420-1.2.5 TEST AND REPAIR ACTIVITIES. ....................... 420-2 420-1.2.6 PARTS. ....................................... 420-2 420-1.2.6.1 Coordinated Shipboard Allowance List (COSAL). ........ 420-2 420-1.2.6.2 Equipment Selection. ........................ 420-3 420-1.2.7 EQUIPMENT INSTALLATION. ......................... 420-3 420-1.2.8 RECORDS AND REPORTS. ........................... 420-3 420-1.2.9 PREVENTIVE MAINTENANCE. ........................ 420-3 420-1.2.9.1 Routine Maintenance. ........................ 420-3 420-1.2.9.2 Safety Precautions.
    [Show full text]
  • Sperry Gyroscope Company Division Records 1915
    Sperry Gyroscope Company Division records 1915 This finding aid was produced using ArchivesSpace on September 14, 2021. Description is written in: English. Describing Archives: A Content Standard Manuscripts and Archives PO Box 3630 Wilmington, Delaware 19807 [email protected] URL: http://www.hagley.org/library Sperry Gyroscope Company Division records 1915 Table of Contents Summary Information .................................................................................................................................... 3 Historical Note ............................................................................................................................................... 3 Scope and Content ......................................................................................................................................... 4 Administrative Information ............................................................................................................................ 5 Related Materials ........................................................................................................................................... 5 Controlled Access Headings .......................................................................................................................... 6 Bibliography ................................................................................................................................................... 6 Collection Inventory ......................................................................................................................................
    [Show full text]
  • The Gyroscope and Its Applications
    AG A R D- Rd82-71 N5 OQ Y p! d p! U c3 U AGARD REPORT No. 582 A Literature Survey on The Gyroscope and its Applications by Dr-Ing Helmut Sorg DlSTRlBUTlO N AND AVAl LAB1LlTY ON BACKCOVER NORTH ATLANTIC TREATY ORGANIZATION ADVISORY GROUP FOR AEROSPACE RESEARCH AND DEVELOPMENT (ORGANISATION DU TRAITE DE L‘ATLANTIQUE NORD) / on THE GYROSCOPE AND -- - by Institut A fur Mechanik, Universitat Stuttgart , Report listing books in the field of gyroscopes prepared for the Guidance and Control Panel of AGARD Published February 197 1 53.082.16 Printed by Technical Editing and Reproduction Ltd Harford House, 7-9 Charlotte St. London. WIP IHD 11 2 2 Pi Pi 00 00 2 z IA v) a 3 0 a e1 0% FOREWORD In the last decade many books about gyroscopes and their applications have been published. The purpose of this report is to offer engineers and scientists a listing of books which are readily available from commercial sources, as well as from various documentation centers and libraries. Only books which were unclassified and unrestricted were considered for this bibliographical listing. This list is a comprehensive tabulation of works by engineers and scientists in the various NATO nations. It also includes some Russian texts on the subject, many of which have been translated into English. It is believed that this list will contribute to broaden the knowledge and prevent a duplication of research in the field of gyroscopes. C.T.Leondes Professor iii ABBREVIATIONS Appl. Mech. Rev. Applied Mechanics Reviews The American Society of Mechanical Engineers United Engineering Center, New York, N.Y., 10017 CFSTI Clearing House for Federal Scientific and Technical Information US Department of Commerce, 5285 Port Royal Road, Springfield, Virginia 22 15 1 Eng.
    [Show full text]