DOCSLIB.ORG

Operations Guide Adjusting Tilted Picatinny Rail

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Operations Guide Adjusting Tilted Picatinny Rail CONSUMER INFORMATION 2 TABLE OF CONTENTS 3 PARTS & HARDWARE 4 Please read LEGAL WARNING before use. Read and CONSUMER INFORMATION understand all instructions. Warning and Caution Statements .............................pg. 2 Legal Warning .........................................................pg. 3 To Our Valued Customer, PARTS & HARDWARE ........................................... pg. 4-5 Sling Stud IPOD We are very pleased to welcome you to the Accuracy Solutions B family of products with your purchase of BipodeXt™. OPERATION Special care is required when working on or shooting a rifle. We Bipods that attach to a Sling Stud ............................ pg. 7 Bubble Level 5-Slot Picatinny Rail Picatinny 5-Slot encourage proper training and licensing before modifying or ofor forward the Unimount Bipods that attach to a Picatinny Rail .........................pg. 7 be mounted to the rear, Can operating a firearm. Installing Tilted Picatinny Rail on a Sporting Rifle .......... pg. 8-11 Proper mounting and safe use of your BipodeXt™ is our desire, -Method 1.) Drilling Holes Through Forearm but your responsibility. -Method 2.) Installing Threaded Inserts Attaching BipodeXt ™ to a Rifle ................................ pg. 12 Thank you very much for your purchase and please enjoy this Customizing BipodeXt ™ to the Operator .................. pg. 12-13 Extending Tube product safely. Extending BipodeXt ™ ............................................ pg. 14 Extreme Canting Correction................................... pg. 14 Sincerely, Clamp Locking Operations Guide Adjusting Tilted Picatinny Rail.................................. pg. 15 Accuracy Solutions LLC Accuracy Solutions LEGAL WARNING It is the consumer’s responsibility to know, understand, and For Models PLEASE PAY ATTENTION TO ALL WARNINGS AND comply with all state, federal, and local laws and regulations. Stability Unimount Stability CAUTION STATEMENTS Certain configurations of firearms may be regulated within your TAC II state. Ensure that the use and installation of the BipodeXt™ is lawful prior to purchase and use. & WARNING statements are designed to alert you to the TAC III possibility of personal injury, loss of life, damage Before working on your firearm make sure that it is not to the BipodeXt ™ and/or personal property if the loaded with ammunition. Never aim a firearm in the instructions are not followed. direction of a person or anything of value, even if the Patents Pending Worldwide firearm is not loaded. Base Tube CAUTION statements are designed to alert you to the possibility of damage to BipodeXt ™ or personal Illustrations in the Assembly & Operations Guide may Bubble Level WARNING: Read all warnings before attempting to install, use or service the Tilted Assembly (1) Telescoping Picatinny Rail system. property if the instructions given are not followed. differ from actual product. Accuracy Solutions LLC. All rights reserved. V 1.1 3/26/2018 Accuracy Solutions LLC. All rights reserved. V 1.1 3/26/2018 Accuracy Solutions LLC. All rights reserved. V 1.1 3/26/2018 Bipods that attach to a Sling Stud (Harris Type) Installing Tilted Picatinny Rail on a (4) Assorted Bolts for (1) 13 Slot Tilted OPERATION Tilted Rail Installation* Picatinny 5 6 7 Sporting Rifle 8 Rail Sling Stud (1) #10-32 x 3/4” BipodeXt ™ is made to fit two types of rifles. 1.) Tactical Rifles (rifles DO NOT ATTEMPT to install the Tilted Picatinny Rail (1) #10-32 x 1” Tilt is already equipped with, or that can easily receive, a Picatinny Rail) If you do not possess the necessary workmanship (1) #10-32 x 1.1/4” adjustable and 2.) Sporting Rifles (rifles without a Picatinny Rail). skills and required tools. The following are simplistic (1) #10-32 x 1.1/2” by sanding the images meant ONLY as a general guide to the required bottom of the If your rifle does not come equipped with a Picatinny Rail rail. pg. 15 installation. These are NOT detailed instructions. If installed on the bottom of the forearm you will need to install you are not completely comfortable in performing the Tilt: 4.33° (260 MOA) one (provided) in order to fasten BipodeXt ™ to your rifle. We have also included a Tilted Picatinny Rail to account for the steep work you should instead take the installation job to a taper of angled forearms on most sporting rifles. This allows professional gunsmith. Typically a qualified gunsmith is (4) Allen Wrenches the BipodeXt ™ to be mounted parallel to the axis of the bore, able to perform this installation in approx. one hour. (3) #10 Hex Nuts however, a slight deviation of axial alignment will not interfere with the performance of BipodeXt ™ There are two methods of installation: 1.) Drilling holes through (3) #10 Lock Washers the forearm, 2.) Installing Threaded Inserts. For wooden rifles both methods work. For most synthetic rifles’ stocks method 1 is Fitting of the Tilted Rail may be required. If you do not (3) #10 Flat Washers recommended. Refer to pg. 15 if altering the angle of the Tilted Rail is required possess the necessary skills and tools, please have this Bolts, Nuts & Washers are made of installation performed by a trained gunsmith. Telescoping Assembly Failure to correctly disassemble and re-assemble a rifle rust-resistant Wax Coated, Black (3) Threaded or to correctly install the Tilted Picatinny Rail could result Oxide Stainless Steel. Inserts in damage to your rifle and/or affect the performance BipodeXt ™ is made to receive two different types of bipods, the of BipodeXt ™ causing serious injury or death. *NOTE: only (3) Bolts are needed to ones that attach to a Sling Stud and the ones that attach to a Bipods that attach to a Picatinny Rail install the Tilted Picatinny Rail, but we Picatinny Rail. The design of the Telescoping Assembly allows for 29/64” Outside Diameter both types of Bipods to be attached simultaneously. (U.S. Mil-STD-1913) Please consult your rifle manufacturer’s instructions guide (owners have included an assortment of eight (4) manual) or consult a trained professional on how to properly bolts with varying lengths to allow the separate the barreled action from the rifle stock. user to adapt to as many rifle forearms (2) 13 Slot Picatinny Rails The 5-Slot Picatinny Rail comes pre-installed to the Telescoping as possible. Assembly. To install the bipod please refer to the instructions We do not recommend attaching your bipod until provided by your bipod’s manufacturer. Method 1.) Drilling Holes Through Forearm BipodeXt™ is fully assembled. Please refer to your bipod user manual for attachment instructions (1) 16 Slot Picatinny Rail KeyMod Failure to install the Bipod correctly per the manufact- Before working on your stock we recommend urers specifications could yield unwanted results, practicing on scrap wood. possibly causing damage, injury or death. If you are M-LOK operating two bipods simultaneously make sure neith- Failure to install the Bipod correctly per the er bipod comes into contact with the barrel of the rifle. Use the Tilted Picatinny Rail to mark holes manufacturers specifications could yield unwanted Disruption of barrel harmonics could yield unwanted where you will drill into the forearm of Flat Back results possibly causing damage, injury or death. results, possibly causing damage, injury or death. the rifle stock. We suggest you install the Tilted Picatinny Rail as far back Accuracy Solutions LLC. All rights reserved. V 1.1 3/26/2018 Accuracy Solutions LLC. All rights reserved. V 1.1 3/26/2018 Accuracy Solutions LLC. All rights reserved. V 1.1 3/26/2018 Accuracy Solutions LLC. All rights reserved. V 1.1 3/26/2018 and close to the recoil lug as possible, while making Repeat the above Use the Tilted Picatinny Attaching BipodeXt™ to a Rifle sure that the installation will not interfere with the procedure for the Rail to mark holes where proper functioning of the rifle. 9 remaining two Bolts, 10 you will drill into the 11 Once your rifle is equipped with an appropriate 12 Flat Washers, Lock forearm of the rifle stock. Picatinny Rail mounted at the bottom of its forend you Washers and Hex Nuts, We suggest you install may attach BipodeXt ™ to it. the Tilted Picatinny Rail as far Drill holes Quick Detach Lever perpendicularly to the back and close to the recoil To attach BipodeXt ™ Unlocked To Lock barrel channel. Since lug as possible, while making first unlock both the bolts are 3/16” in sure that the installation will Quick Detach diameter we recommend not interfere with the proper Levers. This using a 1/4” drill bit. functioning of the rifle. will widen the Unimount’s clamps so you can place the clamps over the Picatinny Rail. There is no need to pierce the forearm of the stock, only drill deep enough to fit the Tension Knobs Unimount provided Threaded Inserts into place. We recommend a depth of 5/8” with a 23/64” drill bit. Lock by pushing down on the levers to fit securely so there is no Once the forearm is drilled, screw in Threaded Inserts with a flat movement. Adjust the Tension Knobs of the levers’ counter bolt while paying attention to the selected bolts‘ length(s). Ensure that head screw driver until they are flush with the forearm. Place as needed. Do this for both levers. neither the Bolts nor the Hex Nuts raise above the Counter-Bore the Tilted Picatinny Rail over the Threaded Inserts. First insert hole as they should never touch the rifle’s barrel. Tighten, to a the Bolt through Lock Washer, Flat Washer and then through Counter-Bore each hole minimum of 20 lbs/in of pressure but do not exceed 30 lbs/in in the barrel channel of of pressure. Confirm the shallow end of the Tilted Rail is pointed the rifle forearm to make towards the butt stock of the rifle and the serrated area of the Rail is room for the Washers pointed away from the barrel.
Load more

Recommended publications
  • Instruction for Vector Optics Tactical Bipod Mounts ATTENTION: Make Sure Firearm Is Unloaded Universal Picatinny Style
    Instruction for Vector Optics Tactical Bipod Mounts ATTENTION: Make sure firearm is unloaded Universal Picatinny Style Fit 21mm weaver and picatinny rail Press down the lockable button to open or folder the bipod Turn and release the leg sleeve, the spring loaded leg will be extended, then fasten the leg sleeve again To retract the leg, loosen the leg sleeve, push back the leg to the end, retighten the leg sleeve again Solid rubber feet avoid slipping With barrel mount adapter Stud Connection Style Stud connection mount for sling attachment Press the button to release the spring loaded leg If need to retract the extendable leg, just press the button again and push the leg back Solid rubber feet avoid slipping With weaver picatinny mount adapter. To use the adapter, remove the bipod tiny rubber sleeve, clamp into the adapter stud hole. Fasten the bottom nut. Swivel Stud Connection Style Swivel stud connection mount for sling swivel attachment Press the button to release the spring loaded leg 15 inch bipod, press first button and pull the extendable legs, press last button to release the spring loaded leg If need to retract the extendable leg, just press the button again and push the leg back Solid rubber feet avoid slipping Weaver picatinny mount adapter. To use the adapter, remove the bipod tiny rubber sleeve, clamp into the adapter stud hole. Fasten the bottom nut. Swing-able design for leveling on uneven ground. Select proper angle and fasten thumb nut to lock the position www.scvector.biz www.scvector.com .
    [Show full text]
  • Manson Precision Receiver Accurizing System
    Manson Precision Receiver Accurizing System Rhomboidal and pavid Slim reinterred her sundries feign or municipalizes estimably. Bewhiskered and dorsiventral Shurlock often disorientates some suspiration jeopardously or gumshoe therapeutically. Toothsome Ned sometimes climb-downs any hypogyny objectivize thriftily. Austenite molecular structure in receiver accurizing your order to impact forging die was attached to It has a receiver accurizing and precision machined hand when needed. National Match Rifle, Serial No. Ups For Remington Centerfire Rifles MAGAZINE CLIP is best carrying cases for extra ammo; they spoke right knowledge the gun. Available in precision manufacturing, deeply serrated face! Winchester receiver accurizing system and precision receiver, butt plate screw only received and the systems, the barrel bore. Sold had designed by the receiver accurizing kit! If they are precision. Even directional change the receiver accurizing system for precise, fulton armory operating rod rail hand and flexibility. The replacement magazine followers should have three neat and evenly spaced spot welds attaching the stop to the follower. End to match category will enlarge due to. The magazines were rotated for even use and the rate of fire was measured during one of the twenty round bursts. It is precision receiver accurizing system was unable to do so you wont need to work was a manson. He fled to the jungle the same day. SPECS: Aluminum, anodized, red. The reamer has a FLOATING pilot that measures approx. Bush and receiver. SPECS: Stainless steel, belt finish. Tactical Forums discussion board www. Low maintenance, Parkerized finish resists corrosion and matches the rest of your rifle. This corn is therefore excellent turnover and fluctuate barely ever used.
    [Show full text]
  • Art of Precision
    2017 CATALOGUE ART OF PRECISION «Promtechnologia» (Industrial Technology) company directs careful attention to its products’ quality which allows it to gain some impressive results: Orsis rifles’ accuracy exceeds their most common counterparts’ results greatly. This reality is confirmed by the multiple winning scores of shooters participating in high-accuracy shooting international competitions with their Orsis rifles in hands. There is a parameter in ballistics called “minute of angle” (or MOA) which estimates accuracy of shooting and it is defined, as a rule, by a group of 3-5 shots. Rifles having MOA ratio less than 1 are called sniper rifles. «Promtechnologia» company guarantees that all Orsis rifles demonstrate accuracy not over 0.5 MOA and a number of models demonstrate even better performance. www.orsis.com 3 President’s Message 4 Orsis Special 6 Orsis SE T-5000 M 8 Orsis M-15 Carbine 12 Orsis AR-10 National Match 16 Orsis Hunting 20 Orsis 120/140 22 Orsis SE Hunter M 26 Orsis SE Alpine M 30 Marocchi Si12 / Walnut 34 T-5000 / 8-11 120/140 / 22-25 Varmint / 48-51 Marocchi Si12 / Plastic 36 Marocchi First-E 40 Marocchi First-E Deluxe 42 Orsis Sport 46 Orsis Varmint M 48 Orsis F-Class 52 Glock Pistols 54 M-15 / 12-15 Hunter / 26-29 F-Class / 52-53 Production 56 High-Technology Equipment 58 High-Precision Technologies 59 Exceptional Materials 60 Innovative Development 61 International Cooperation 61 AR-10 / 16-19 Alpine / 30-33 Glock / 54-55 Services 62 Rifle Barrels Replacement 63 Cerakote Coating Application 63 Technical Maintenance 64 Decoration & Engraving 65 Orsis Сustom 65 Dealer Network 66 Marocchi / 34-45 Contacts 66 HIGH-PRECISION FIREARMS SYSTEMS ORSIS 4 ORSIS ART OF PRECISION President’s Message 5 Dear friends! The first catalogue of «Promtechnologia» (Industrial Technology) We support our shooters’ aspiration to be the best hunters and company is now introduced for your kind attention and, as you will sportsmen.
    [Show full text]
  • CASV Handguard for the FAL Rifle Note: the CASV-FAL System Will Not Fit on Rifles Using the G1 Or Similarly Profiled Barrels
    CASV Handguard for the FAL Rifle Note: The CASV-FAL System will not fit on rifles using the G1 or similarly profiled barrels Improper installation can result in damage. Do not attempt installation if you are not familiar with the firearm, tools and techniques mentioned. You are responsible for any damage or READ injury resulting from the improper use THIS! or installation of this product. Ensure the rifle is CLEAR and SAFE! Before installation, read Instructions, Warnings and Notes. NOTE: Make sure that the firearm is unloaded and safe before proceeding – if you are unsure of how, or uncomfortable with the proper clearing and safe handling of the firearm, do not proceed! We recommend that the installation of this part be done only by a qualified gunsmith or agency armorer. 1. Before proceeding, please inspect the handguard assembly and hardware to ensure that you are familiar with all of the parts. 1 - Upper handguard Assembly 2 - Lower handguard Assembly 3 - Forward mounting screw retaining clip 4 - Forward mounting screw 5 - Rear mounting cross screw 6 - Rear mounting clamping nut 7 - Upper Handguard retaining screws (6 for FAS, 8 for FAL) 8 - Picatinny Accessory Rails & Screws 2. Install the lower handguard section by sliding it over the front sight gas block, and rearward over the handguard retainer. After the lower section is in place, install the forward mounting screw from the right side of the handguard, ensuring that it goes through the front sight gas block. Note: only snug the screw enough to hold the lower handguard section in place. 3.
    [Show full text]
  • PM Crew Served Weapons Overview Small Arms Symposium & Exhibition
    TheThe Soldier:Soldier: America’sAmerica’s MostMost DeployedDeployed CombatCombat SystemSystem PM Crew Served Weapons Overview for the Small Arms Symposium & Exhibition National Defense Industrial Association 16-19 May 2006 BG James R. Moran COL Carl A. Lipsit Mr. Peter Errante Program Executive Officer Soldier PM Soldier Weapons Deputy PM Crew Served Weapons Crew Served Weapons 2 PM Soldier Weapons Programs List DEVELOPMENT WEAPONS PROCUREMENT Objective Individual Combat Weapon (OICW) 37. M101, CROWS, Remote Mount 1. OICW Increment I 38. M151E1 & M151E2 Protector Remote Wpn System (RWS) 2. OICW Increment II - XM25 Air Burst Weapon 39. MK19 Advanced Crew Served Weapons (ACSW) 40. Mod Kit 3. Advanced Crew Served Weapon (ACSW) Programs 41. Lightweight Adjustable Sight Bracket 42. Tactical Engagement Simulator (TES) SOLDIER ENHANCEMENT PROGRAMS 43. M107 Semi Automatic Long Range Sniper Rifle 4. XM26 - 12 Gauge Modular Accessory Shotgun System 44. M240B, 7.62mm Medium MG (MASS) 45. M240B Collapsible Buttstock 5. Joint Combat Pistol 46. M192, Light Weight Ground Mount For MG 6. Family of Small Arms Suppressors 47. Improved Bipod 7. M68 Close Combat Optics (Dual Source Qualification) 48. Improved Flash Suppressor 8. XM1068, 12 Gauge Non-Lethal Extended Range Round 49. Combat Ammunition Pack 9. XM1022, Sniper Ammunition for M107 50. M240B Short Barrel 10. XM110 - 7.62 Semi-Automatic Sniper System (SASS) 51. M240B Improved Buttstock 11. Close Quarters Battle Kit 52. Sling Assembly for the M240B 12. XM1041/XM1042/XM1071 - Close Combat Mission 53. Short Barrel Capability Kit 54. M249, 5.56mm Squad Automatic Weapon 13. Advanced Sniper Accessory Kit (ASAK) 55. M192, Lightweight Ground Mount For MG 14.
    [Show full text]
  • Orders: 800-741-0015
    HOWARD LEIGHT 3M PELTOR TRI-FLANGE ACCESSORIES SHOOTING SHOOTING ACCESSORIES INDEX IMPACT BOLT MUFFS REUSABLE EARPLUGS Ammo Boxes & Range Gear ........ 361 Safety & Training Aids ........ 370-371 Impressivley FAST Electronic Sound Comfortable, Snug Fit To Seal Magazine Loaders ............ 367-368 Shooting Aids ............... 368-370 Suppression + Other Feature Upgrades Out The Noise - Full 26 NRR Howard Leight’s premium electronic Impact Soft, triple flanged plugs adapt Protective Gear ................ 359-360 Timers & Chronographs ....... 366-367 Bolt muffs turn the amplifier on and off about 250 to the shape of the ear canal for a times faster than typical electronic muffs. That custom fit that protects your hear- Rests & Bipods ............... 362-366 means, as soon as a gunshot-noise spike over 82 dB is detected, the ing from loud noises. Made of pliable, non-irritating polymer, these circuits shut down the audio in ½ millisecond. When the noise has earplugs have a plastic stem that lets you quickly and easily insert passed, the amplifier turns back on just as quickly. This speed keeps the plugs without touching the pre-molded tips. They're washable, you connected to your shooting environment by eliminating sound- ® Colors too, so you'll get plenty of range sessions out of the. Poly cord keeps SIMS VIBRATION LABORATORY LIMBSAVER clipping - the inadvertent blocking of ambient sounds just after a them together when in use or storage, and the bold, hi-viz fluores- HOWARD LEIGHT IMPACT SPORT gunshot. The result is you don’t experience that odd sense of “discon- cent green color makes them even harder to lose! ab PROTECTIVE SHOOTING PAD nection” common to electronic muffs, helping you hear range com- SPECS: Soft polymer, florescent green.
    [Show full text]
  • Assembly and Operations Guide
    BIPOD ® Assembly and Operations Guide For Model Numbers BXT-34X2 BXT-40X2 BXT-40X3 Patents Pending Before Several Jurisdictions WARNING: Read all warnings before attempting to install, use or service the Tilted Picatinny Rail system. CONSUMER INFORMATION Please read LEGAL WARNING before use. Read and understand all instructions. To Our Valued Customers, We are very pleased to welcome you to the Accuracy Solutions family of products with your purchase of BIPODEXT ™. Special care is required when working on or shooting a rifle. We encourage proper training and licensing before modifying or operating a firearm. Proper mounting and safe use of your BIPODEXT ™ is our wish but your responsibility. Thank you very much for your purchase and please enjoy this product safely. Sincerely, Accuracy Solutions LLC PLEASE PAY ATTENTION TO ALL WARNING AND CAUTION STATEMENTS WARNING statements are designed to alert you to the possibility of personal injury, loss of life, damage to the BIPODEXT ™ and/or personal property if the instructions are not followed. CAUTION statements are designed to alert you to the possibility of damage to BIPODEXT ™ or personal property if the instructions given are not followed. Accuracy Solutions LLC. All rights reserved. 2 Rev. 1.0, August 10, 2017 TABLE OF CONTENTS CONSUMER INFORMATION Warning and Caution Statements .............................pg. 2 Legal Warning .......................................................pg. 3 PARTS & HARDWARE .....................................pg. 4-5 ASSEMBLY Bipods that attach to a Sling Stud ............................pg. 6-7 Bipods that attach to a Picatinny Rail .........................pg. 7 Installing Tilted Picatinny Rail on a Hunting Rifle Method 1.) Drilling holes through forearm ................pg. 8-10 Method 2.) Installing Threaded Inserts .....................pg.
    [Show full text]
  • (12) United States Patent (10) Patent No.: US 7,121,034 B2 Keng (45) Date of Patent: Oct
    USOO7121034B2 (12) United States Patent (10) Patent No.: US 7,121,034 B2 Keng (45) Date of Patent: Oct. 17, 2006 (54) BPOD MOUNT AND GRIPASSEMBLY 6,487,807 B1 * 12/2002 Kopman et al. ............... 42.94 2005/0241206 A1* 11/2005 Teetzel et al. ................. 42.72 (76) Inventor: Da Keng, 875 Wharton Dr. S.W., Atlanta, GA (US) 30336 FOREIGN PATENT DOCUMENTS (*) Notice: Subject to any disclaimer, the term of this DE 103.108O2 A1 * 9, 2004 patent is extended or adjusted under 35 U.S.C. 154(b) by 0 days. * cited by examiner Primary Examiner J. Woodrow Eldred (21) Appl. No.: 11/056,134 (74) Attorney, Agent, or Firm Jones Tullar & Cooper, PC (22) Filed: Feb. 14, 2005 (57) ABSTRACT (65) Prior Publication Data A grip and bipod mounting device for mounting a bipod US 2005/O188588 A1 Sep. 1, 2005 Supporting grip assembly to a "picatinny’ mounting rail structure as are often affixed below the forearm stock of a Related U.S. Application Data firearm such as a military rifle (e.g., as per standard MIL STD-1913). In particular, the present invention is directed to (60) Provisional application No. 60/543,571, filed on Feb. mounting a Parker-Hale style of firearm bipod on a bipod 12, 2004. Supporting grip assembly including a contoured mounting (51) Int. C. block segment inletted to cover and attach to a picatinny rail affixed beneath the forearm stock of the firearm. A grip or F4 IC 23/00 (2006.01) handle depends transversely from the mounting block seg (52) U.S.
    [Show full text]
  • Universal Featherweight Bipod
    UNIVERSAL FEATHERWEIGHT BIPOD FitS: Any Firearm with a Sling Swivel Stud and AR-15 Types INSTALLATION INSTRUCTIONS PART# BIP0300 MAKE SURE YOUR FIREARM IS UNLOADED BEFORE STARTING! UNIVERSAL BIPOD ASSEMBLY: INSPECT EXISTING SLING SWIVEL STUD FOR TIGHTNESS! NON-SWIVEL SWIVEL Mounting O-Ring Bracket (Swivel Only) (See Step #9) Depress “Snap-n-Lock” button to fold Non-Swivel legs forward, OR IMPORTANT: Collar down or (See Step #10) Fits AR-15 with ROUND Mil Spec Yoke Assembly rearward Twist knurled knob Swivel Collar Handguards Without Modification. Halves to extend, retract M-4 Requires Additional Hole. or lock legs Fits any Rifle with Sling Swivel Stud OR Assemble Universal Bipod: Counterbore Washer Flat Top Washer 1. After deciding to build non-swivel or swivel bipod, position mounting bracket as shown in picture at right, install either the non-swivel collar or the swivel collar in the assembly. #10 x 3/4 Screws 2. Install non-swivel collar or swivel collar halves onto top side of mounting bracket with Thick Thick pins aligning with holes in mounting bracket. Washer Washer 3. If swivel collar halves were used, place o-ring into groove on top side of mounting bracket. Left Leg Right Leg 4. Install yoke assembly over post on mounting bracket and align (2) pins on bottom of yoke with holes in non-swivel collar or in open area between swivel collar halves. 5. Install washer over the post and secure with the pink pre-coated #10 x 3/4 screw using a Phillips screw driver. NOTE: Non-swivel Bipod will use the washer with the counterbore INSTALLING BIPOD TO RIFLE: top and Swivel Bipod will use the washer with the flat top.
    [Show full text]
  • Fabdefence.Pdf
    2012 2-15 grips 16-29 rail systems 30-33 K-pos 34-45 Buttstocks 46-53 TACTICAL FLASHLIGHT ADAPTORS 54-59 Magazine accessories 60-69 parts & upgrades 70-71 Self-Healing Targets 72 index gripsTarget Accuracy AG-43 AGF-43S AR15/M16 Pistol Grip Tactical Folding Pistol Grip for-M16-M4-AR15 Finger Swelts and a Backstrap Shape Designed to Enhance Transforms a Horizontal Positioned Grip to Vertical Position Grip, Even when Wet Weapon Fits Easier in Gun Case and on Weapon Rack Extended Beavertail for Better Control, Allowing a Higher Firmer Hold Provides Easier Maneuverability, more Convenient for Undercover Readily Accessible Storage Area with Securely Sealed Hinged Door Work and Concealment MIL-SPEC Reinforced Polymer Composite Easier and Faster Vehicular Deployment Available in Black and Two Camouflage Colors: Olive Drab Green and Desert Tan Quick Fold/Unfold Button Made From Reinforced Polymer Composite 04 Grips AG-47 AG-58 SG-1 Ergonomic Pistol Grip for AK-47/74 SA. VZ. 58 Pistol Grip Sniper Pistol Grip Advanced Ergonomic Design Prevents Unique Texture Prevents Slipping Replaces Standard Pistol Grip To Provide Wrist Fatigue and Ensures Secure Grip in When Wet Greater Comfort and Operational Control Wet Conditions Advanced Ergonomic Design Advanced Ergonomic Design Improves Trigger Operation Built-In Storage Compartment Adjustable Palm Swell Style Grip Built-In Storage with Removable Enhances Finger to Trigger Correspondence Adapts Easily To Various Sized Hands Cushioned Battery Holder Tough Material & Design Applies Pressure to the Palm of the Hand Manufactured with MIL-SPEC Reinforced Available in Black and Two Camouflage Allowing Deliberate and Measured Polymer Composite Colors: Olive Drab Green, and Desert Tan Trigger Pull Available in Black and Two Camouflage Tough Material & Design Colors: Olive Drab Green, and Desert Tan Available in Black 05 Grips agr-870 agm-500 wg-1911 Remington 870 Pistol Grip Mossberg 500 Pistol Grip 1911 Mag.
    [Show full text]
  • 2020 Product Catalog American Defense Manufacturing Is a Leader in Contents Mounting Solutions for a Variety of Optics, Lights, Lasers and Accessories for Firearms
    2020 Product Catalog American Defense Manufacturing is a leader in Contents mounting solutions for a variety of optics, lights, lasers and accessories for firearms. The proprietary Quick Disconnect Auto Lock system is unrivaled when 3-4 New Products it comes to locking, adjustable quick disconnect 5-8 Optics mounts and is the backbone of ADM. 9-10 Optic Packages In 2015, ADM proudly introduced the Universal 11 Mount Introduction Improved Carbine (UIC), one of the finest lines of AR-15 style rifles offering true, fully ambidextrous 12 QD Autolock controls and overbuilt components. 13-18 Red Dot Mounts Today, American Defense Mfg capitalized on their 19-26 Magnified Scope Mounts mount and firearm experience to develop a unique 27 Accessory Mounts line of optics designed specifically for the AR15 but 28 Bipod Mounts ideal for shotguns, subguns, muzzleloaders and more. 29-30 Light Mounts Welcome to American Defense 2020. 31-32 Miscellaneous Mounts 33-34 Non-QD GI Bolt Mounts 35-38 Legacy Lever Mounts 39-46 Rifle Systems 47-49 Rifle Components 50 Information TIONAL N LY E T N I R S I O U P E R This commercial marketing catalog does not contain technical data whose export is restricted by the Arms Export Control Act or International Traffic in Arms Regulations. All information is subject to change without notice. NEW PRODUCTS NEW PRODUCTS ADM PRC-700SA Chassis New ADM Mounts The new ADM PRC-700SA chassis is designed with the precision rifle competitor in mind. Accepting common AICS magazines, this chassis is engineered with features and components that will help you make successful shots from the most dynamic or improvised positions.
    [Show full text]
  • Keymod™ Vs. M-LOK™ Modular Rail System Comparison
    CAPT JT Elder Commanding Officer NSWC Crane KeyMod™ vs. M-LOK™ Modular Rail System Comparison Dr. Brett Seidle, SES Abstract #19427 Technical Director NSWC Crane Presented By: Caleb McGee Date: 4 May 2017 Distribution Statement A – approved for public release; distribution unlimited Background History • The MIL-STD-1913 Accessory Mounting Rail was standardized in 1995. • MIL-STD-1913 Quad-rail Handguards currently in use. – MK18 Mod 1 Carbine. – Upper Receiver Group (URG). • Industry developed, low profile handguards with “as needed” accessory mounting panels. – Rail panels can be positioned using holes machined into the handguard. Distribution Statement A – approved for public release; distribution unlimited Background KeyMod™ • Originated by VLTOR Weapon Systems and released in 2012. • Developed as a standardized accessory mount platform. • Supports direct mounting of accessories and 1913 accessory rail sections. • Current civilian market moving towards direct mounting of accessories. • KeyMod™ accessories interface with KeyMod™ handguards by: – Inserting mounting nuts of accessory through the large portion of the KeyMod™ slot. – Sliding the accessory fully forward in smaller front portion of key shaped slot. – Tightening accessory bolts to secure in place. Distribution Statement A – approved for public release; distribution unlimited Background M-LOK™ • Originated and released by MAGPUL in early 2015. • MAGPUL cites improved performance in polymer accessories using M-LOK™. • Allows for mounting of accessory rails to low-profile handguard designs. • Functions by passing mounting T-nuts on an accessory through the slots in the handguard. • Tightening the accessory bolts rotates the T-nuts to rotate 90° and lock, allowing the bolts to be torqued. Distribution Statement A – approved for public release; distribution unlimited Overview Objectives • Qualitative and quantitative comparisons of both the KeyMod™ and M-LOK™ accessory mounting systems.
    [Show full text]