Power Focus 6000 Printed Matter No

Power Focus 6000 Printed Matter No

Power Focus 6000 Printed Matter No. 9839 1023 01 Valid for Version No. 2.7 2018-01-30 Configuration guide Software version 2.7 Valid from 2017-11 WARNING Read all safety warnings and instructions Failure to follow the safety warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference Table of Contents Overview ....................................................................................... 9 Notice ...................................................................................... 9 Introduction ................................................................................ 10 About the Configuration Manual............................................ 10 Revision history..................................................................... 10 Target group.......................................................................... 11 Prerequisites ......................................................................... 11 Typographic conventions ...................................................... 12 Terms and definitions............................................................ 12 Power Focus user interface ...................................................... 13 Operating and handling......................................................... 13 Front panel................................................................... 13 Web GUI ...................................................................... 14 Menu overview ...................................................................... 14 Tightening menu .......................................................... 14 Batch sequence menu ................................................. 15 Sources menu.............................................................. 15 Tool menu .................................................................... 15 Virtual station menu ..................................................... 15 Controller menu ........................................................... 16 Configurations menu.................................................... 16 Reports menu .............................................................. 16 Settings menu.............................................................. 16 Help menu.................................................................... 17 Configuration overview Power Focus 6000........................... 17 System settings.......................................................................... 18 Network configuration............................................................ 18 Accessing the controller on LAN.................................. 19 Accessing the controller through the web GUI............. 19 Protocol configuration............................................................ 19 Configuring ToolsTalk communication......................... 20 Configuring ToolsNet communication.......................... 20 Configuring a license manager .................................... 21 Preferences........................................................................... 21 Setting the date and time............................................. 21 Setting the displayed controller language.................... 22 Setting the displayed torque unit.................................. 23 Setting the startup screen............................................ 23 2 © Atlas Copco Industrial Technique AB - 9839 1023 01 PIN settings........................................................................... 24 Activating the PIN ........................................................ 24 Configuring new users and assigning PINs ................. 24 Accessing the controller when locked by PIN.............. 25 Tool alarms............................................................................ 25 Tightening settings ................................................................ 25 Wireless................................................................................. 26 Events settings...................................................................... 26 Fieldbus................................................................................. 26 Results .................................................................................. 27 Factory reset ......................................................................... 27 Tool configuration...................................................................... 29 Tool information..................................................................... 29 Tool TAG information................................................... 29 Connection ............................................................................ 30 Health.................................................................................... 30 Tool temperature.......................................................... 30 Maintenance.......................................................................... 30 Calibration ............................................................................. 31 Preparing the calibration.............................................. 32 Calibrating the tool....................................................... 32 Motor tuning .......................................................................... 32 Starting the motor tuning.............................................. 32 WLAN and Bluetooth for wireless tools................................. 33 Bluetooth requirements................................................ 33 Wireless tools restrictions ............................................ 33 Putting an STB tool into pairing mode ......................... 33 Putting an ST Wrench in pairing mode ........................ 33 Pairing a wireless tool to a controller ........................... 34 Troubleshooting: WLAN and Bluetooth........................ 35 Controller menu - Tightening.................................................... 36 Tightening.............................................................................. 36 General Tightening program settings.................................... 36 Name ........................................................................... 37 Strategy........................................................................ 37 Target........................................................................... 38 Time monitoring (elapsed time) ................................... 38 Residual torque correlation factor................................ 38 Trigger Lost.................................................................. 40 Attachment tuning........................................................ 40 © Atlas Copco Industrial Technique AB - 9839 1023 01 3 Tightening program validation and validation error report- ing.......................................................................................... 41 Validation error reporting ............................................. 42 Validate a tool with a tightening program..................... 42 Start step............................................................................... 42 Direction....................................................................... 43 Soft start....................................................................... 43 Rehit detection............................................................. 44 Current monitoring ....................................................... 44 True angle compensation ............................................ 45 Rundown step ....................................................................... 46 Selftap.......................................................................... 46 Rundown torque limits ................................................. 47 Rundown angle limits................................................... 48 Post view torque .......................................................... 49 Rundown complete ...................................................... 50 Tightening step...................................................................... 50 Tightening strategies.................................................... 50 Target torque limits ...................................................... 56 Target angle limits........................................................ 57 Torque compensation .................................................. 59 Stop step ............................................................................... 59 Soft stop....................................................................... 59 Loosening step...................................................................... 59 Pulse tightening with direct driven electrical tools................. 60 TensorPulse tightening program ........................................... 61 Tightening using the TensorPulse program .......................... 64 Impulse single step tightening program................................. 66 Four Step tightening strategy................................................... 70 Introduction to the four step tightening strategy .................... 70 Overview of the four step tightening strategy........................ 70 Parameter definition .............................................................. 72 Parameters for four step tightening - start step..................... 72 Parameters for four step tightening - rundown step .............. 75 Parameters for four step tightening - first tightening step of the tightening step............................................................

View Full Text

Details

  • File Type
    pdf
  • Upload Time
    -
  • Content Languages
    English
  • Upload User
    Anonymous/Not logged-in
  • File Pages
    284 Page
  • File Size
    -

Download

Channel Download Status
Express Download Enable

Copyright

We respect the copyrights and intellectual property rights of all users. All uploaded documents are either original works of the uploader or authorized works of the rightful owners.

  • Not to be reproduced or distributed without explicit permission.
  • Not used for commercial purposes outside of approved use cases.
  • Not used to infringe on the rights of the original creators.
  • If you believe any content infringes your copyright, please contact us immediately.

Support

For help with questions, suggestions, or problems, please contact us