SPECIFICATIONS – JOB SPECIFIC Date: 2/2/2021 RIC No: 2020-CT-054 SPECIFICATIONS – JOB SPECIFIC INDEX Item Code Description Page 100.9902 Schedule of Salaries and Wages JS-1 105.02 Plans and Shop Drawings JS-2 108 Prosecution and Progress JS-4 108.03 Prosecution and Progress JS-5 109.06 Partial Payments JS-6 109.09 Acceptance and Final Payment JS-8 203.0310 Structural Excavation Masonry JS-9 203.0530 Dewatering JS-10 203.9901 Cellular Concrete Fill JS-19 205.9901 Temporary Support of Excavation JS-24 Section 206 Perimeter Erosion Controls JS-25 Section 207 Check Dams JS-30 Section 208 Temporary Dewatering Basins JS-33 Section 209 Storm Drain Protection JS-36 Section 210 Stilling Basins for Water Pollution Control JS-40 Section 211 Construction Access JS-42 Section 212 Maintenance and Cleaning of Erosion and Pollution Controls JS-44 709.9901 Bioretention Basin and Sediment Forebay JS-52 709.9902 Wet Basin Restoration JS-55 801.9901 Fiberglass Reinforced Polymer (FRP) Truss Bridge JS-57 804.9901 Drive Shoes for 12 Inch Pipe Pile JS-66 JS-i Date: 2/2/2021 RIC No: 2020-CT-054 805.9901 Permanent Sheet Piling Composite Furnish and Drive JS-67 808.9901 Concrete Substructure Class HP 3/4” Wall Moment-Slab JS-75 905.9901 Reinforced Drivable Grass Mat JS-76 920.9901 Bedding Stone for Riprap FS-2 JS-78 Section 929 Field Offices JS-79 937.1000 Maintenance and Movement of Traffic Protection Devices JS-86 938.1000 Price Adjustments JS-87 950.9901 Steel Bollard – Permanent JS-88 950.9902 Steel Bollard Removable JS-89 950.9903 Remove and Reset Bench JS-90 T15.9901 Remove and Relocate Informational Sign JS-91 T20.9901 Epoxy Resin Pavement Marking – Speed Hump Symbol JS-92 T20.9902 Epoxy Resin Pavement Marking – Stop Ahead JS-92 L02.0105 Wetland Seed Mix (Type 5) JS-93 L06.9901 Pine Bark Mulch JS-95 L06.9902 Andropogon Gerardii “Big Bluestem” JS-96 L06.9903 Allium Senescens “Ornamental Onion” JS-96 L06.9904 Echinacea Purpurea “Coneflower” JS-96 L06.9905 Panicum Virgatum “Switchgrass” JS-96 L06.9906 Rudbeckia Hirta “Black-Eyed Susan” JS-96 L06.9907 Symphyotrichum Novae-Angliae “New England Aster” JS-96 L06.9908 Schizachyrium Scoparium “Little Bluestem” JS-96 L06.9909 Spartina Alterniflora “Smooth Cord Grass” JS-96 M.07.10.1 Steel Pipe JS-97 JS-ii Date: 9/2/2020 RIC No: 2020-CT-054 JOB SPECIFIC CODE: 100.9902 SCHEDULE OF SALARIES AND WAGES The rates of payment of wages, obligations and charges for labor by the contractor shall be not less than those shown on the following schedule of customary and prevailing rates of wages supplied by the Rhode Island Department of Labor. JS-1 Date: 9/2/2020 RIC No: 2020-CT-054 JOB SPECIFIC CODE: 105.02 PLANS AND SHOP DRAWINGS Plans will show details of all structures, lines, grades, typical cross sections of the roadway, location and design of all structures and a summary of items appearing on the Proposal. Bridge plans will either show all dimensions and details necessary for complete construction or such information that when supplemented by additional field data gathered by the Contractor will enable the Contractor to prepare complete shop drawings. The Contractor shall keep one set of plans and approved shop drawings available at the site at all times. All shop drawings will be submitted in a timely fashion such that the Contractor's approved schedule will not be adversely impacted by the submittal process. Shop drawings shall consist of such detailed plans required to control the work that are not included in the plans furnished by the Department. They shall include but not be limited to dewatering systems, cellular concrete fill, fiberglass reinforced polymer truss bridge components, and composite sheet piling, or any other supplementary plans or similar data required of the Contractor. The Contractor shall submit seven (7) sets of shop drawings to the Engineer. Shop drawings shall be accompanied by three (3) sets of design computations, cuts from a manufacturer's catalog, and/or supporting technical bulletins. In addition to the submission requirements set forth above, the Contractor shall simultaneously submit two sets of the shop drawings, computations, cuts from a manufacturer's catalog, and/or supporting technical bulletins to each of the Engineer's agents (consultants) by courier or overnight delivery service in order to expedite review. The shop drawings shall be delivered to: CDM Smith, Inc. 260 West Exchange Street, Suite 300 Providence, RI 02903 Attn: Lisa Sherman Shop drawings and computations designs shall be stamped only by a Rhode Island registered Professional Engineer. Within forty-five (45) calendar days of submission, all shop drawings shall be reviewed by the Engineer and returned to the Contractor for appropriate action. Shop drawings that are found to be erroneous, lacking information necessary to control construction, or not in conformance with accepted design criteria will be disapproved and returned to the Contractor. The Contractor shall address the Engineer's comments and resubmit revised shop drawings and/or design computations. The Contractor will not be allowed any increase in contract time for the time taken by the Contractor to submit revised shop drawings caused by an erroneous submission, or by a previous submission either lacking the information necessary to control construction, or not conforming to accepted design criteria. JS-2 Date: 9/2/2020 RIC No: 2020-CT-054 Also, the time taken by the Engineer to review the revised shop drawings does not constitute justification for additional contract time. Shop drawings must be approved by the Engineer prior to performance of the work involved. Such approval shall not relieve the Contractor of any responsibility under the contract for the successful completion of the work. Unless otherwise specified in the contract documents, the contract price will include the cost of furnishing all shop drawings. JS-3 Date: 2/2/2021 RIC No: 2020-CT-054 JOB SPECIFIC CODE 108 PROSECUTION AND PROGRESS Replace Subsection 108.01; Subletting of Contract, page 1-56 of the Standard Specifications for Road and Bridge Construction 2004 Edition (Amended March 2018) with all revisions with the following: 108.01 SUBLETTING OF CONTRACT. The Contractor shall not sublet, sell, transfer, assign, or otherwise dispose of the Contract or any portion thereof, or of its right, title, or interest therein, without written consent of the Engineer. If the Engineer gives such consent, the Contractor will only be permitted to sublet a portion thereof. The Contractor shall perform with its own organization work amounting to not less than 40 percent of the adjusted contract cost. The adjusted contract cost is the total contract cost less the total cost of subcontract specialty items listed in the Proposal. Specialty Items are defined in Subsection 101.63. No subcontracts or transfers of Contract shall relieve the Contractor of liability under the Contract and Bonds. A copy of written agreements with subcontractors must be submitted when making application to sublet any work under the Contract. The Contractor shall not require or withhold retainage from subcontractors. Furthermore, no agreements between the Contractor and its subcontractors or vendors shall create any "third party" relationships between said subcontractors or vendors and the State. The Contractor shall provide written notice to, and obtain prior written consent from the Engineer, before allowing any subcontractor to sublet any portion of its work to a lower-tier contractor. In accordance with Section 12.108.08, Failure to Complete on Time, Para. a., Phased Completion, Interim Completion and Substantial Completion the following defines the Interim and Substantial Completion Dates and Associated Liquidated Damages: Substantial Completion: July 31, 2022 All Contract work shall be completed, as defined by Section 101.71. Liquidated Damages: $550.00 per calendar day. JS-4 Date: 9/2/2020 RIC No: 2020-CT-054 JOB SPECIFIC CODE: 108.03 PROSECUTION AND PROGRESS In accordance with Section 108.03; Prosecution and Progress, Para. a.1, General Requirements – Project Schedule Program, the Schedule Level for this contract is Schedule Level B. Replace Subsection 108.03; Prosecution and Progress, Para. a.2., General Requirements-Software with the following: 2. Software The software used to generate the CPM Schedule shall be Primavera P6. The version shall be Version 7 or 8. The Contractor shall purchase and maintain a valid software maintenance agreement for each license of software necessary to produce and maintain the Project Schedules. Unless specified elsewhere in the Contract Documents, the Contractor shall comply with the terminology defined by the Primavera Project Management Manual. JS-5 Date: 9/2/2020 RIC No: 2020-CT-054 JOB SPECIFIC CODE: 109.06 PARTIAL PAYMENTS Replace Subsection 109.06, Partial Payments, pages 1-83 to 1-84 of the RI Standard Specifications for Road and Bridge Construction in its entirety with the following. 109.06 PAYMENT FOR WORK. a. General. The Department will make payment for Work before the Project is accepted and final payment is made. These payments for Work will be processed via progress payments. In order to receive a payment for Work, the Contractor shall prepare an invoice in accordance with Subsection 109.06 paragraph (c.), Invoice for Payment for Work. The Department may suspend progress payments if the Contractor does not comply with the Engineer’s directions or written orders. The Department will notify the Contractor, whenever progress payments will be suspended. Processing of progress payments for Work prior to the Department’s acceptance and final payment of the Work does not constitute the Department’s acceptance of the Work, and does not relieve the Contractor of responsibility for the Work which includes but is not limited to: 1.