Tip: My remote is not responding 2. Follow the diagram inside the Press this Press this 3. Enter the four-digit code. The Note the code set that worked, in The device key’s LED blinks three battery case to insert the new To… To… device key LED turns off briefly case you must re-code your remote: times, indicating it has unlocked the Key Key • Review the information in batteries. after each key press. DVD/VCR: volume control for all devices. “Using Your Remote”to make Motorola DRC800 4-in-1 sure that the key you pressed is You have ten minutes to replace the Mute current audio These functions are set Note: You have 10 seconds to press TV: Universal Remote Control batteries before your remote loses feed by your cable provider each digit. If it takes longer than REASSIGNING DEVICE KEYS active for the device you are memory. that, the remote “times out” and AUDIO: controlling. Jump among pre- These functions are set you must begin again. See “Checking Codes”for more Each device key accesses a specific • Make sure you are controlling by your cable provider type of device (for example, the DVD/ USING YOUR REMOTE selected favorite 4. If the remote recognizes the information on noting code sets. the device you think you are. See channels (only VCR key can only be programmed to “Using Your Remote”for more Enter a channel or code, the device key’s LED blinks available in CABLE control a DVD player, VCR, DVR, or information on choosing a To select a device to control, simply device code number. To three times. You can now test the CHECKING CODES press one of the device mode keys (TV, mode) POWER HTIB system). This makes it easier to device to control. access channels lower remote by pressing . If search for a code if your device’s code AUDIO, DVD/VCR, CABLE) at the top of your device responds (turns off), than 100, you may 1. Press and hold a device mode does not appear on the list provided. • Make sure your batteries are your remote. After you set up the Note: Favorite you have found the right code. If need to enter 3 digits. key (AUDIO, DVD/VCR, or TV) for good. If battery power is low, remote to control that device, you may channels must be pre- your device does not respond, Your new remote allows you to change For example, to access at least six seconds. The LEDs your remote enters a “Low begin using the device. selected through the repeat steps 2 - 3 with the next for each device key light up, then the type of device that may be Battery Condition” to conserve Electronic channel 2, press 0-0-2. See “Programming Device Control” code in the list.. the key for the device you assigned to a device key. That way, if battery power for retaining your Programming Guide For channel 22, press you have two TVs, for example, you for more information on identifying a If the remote does not recognize selected remains on. settings. See “Installing before this key works. 0-2-2. can control them both by changing the Batteries”for more information specific device to a device key. the code, the LED will turn off. 2. Enter 9 9 0 to tell the remote you Input type of device the DVD/VCR or AUDIO on changing the batteries. Display the help screen Select the video source Retry the code (by repeating are verifying the device code. Press this key controls. To… (only available in Aspect Change the viewing steps 2-3 using the next code The LED blinks twice. • Reset all settings: Key CABLE mode) aspect (if available) listed for your brand), or search 1. Press and hold the device mode 3. Press 1, then count the LED key (TV, AUDIO, DVD/VCR, or • Press and hold a device for a device code. See “Searching TV AUDIO DVD/ Turn the selected Return to last selected PIP ON/OFF Turn Picture-in- blinks and write down the Cable) corresponding to the type mode key ( , , for Codes”. VCR Cable device ON or OFF channel Picture (PIP) on or off number. If the LED does not of device you want the , or ) or at least (if available) blink, the number is 0. This is reassigned key to control (for six seconds. The LED for Audio, DVD/VCR, Select a device VOL +/- Increase or decrease SEARCHING FOR CODES the first digit of the device code. TV each device key lights up, PIP SWAP Swap the PIP signal to example, ) for at least six TV, Cable volume Press 2, 3, and 4 to obtain all seconds. The LED for each then the key for the device the main display (if If none of the codes listed under four-code digits. device key lights up, then the key you selected remains on. Direct access to Video CH +/- Select the next or available) “Device Codes”on the back of this On Demand (VOD), previous channel for the device you selected •Enter 9 8 1. PIP Move Move the position of guide match your device, you can remains on. where available Move up or down search for a set of commands that will CHANGING VOLUME LOCK The LED blinks twice to indicate the PIP display 2. Enter 9 9 2. Direct access to Pay Per through menu screens work. Your remote will sample all the that your remote is returned to User Guide PIP CH +/- Locking the volume controls to a its factory settings. You will need View (PPV) or the Electronic Select the next or codes in its system for that device 3. Press the device mode key you previous channel in the mode to find one that will allow you to single device makes it easier to control to reset all device code settings. programming (where Program Guide volume, without having to guess want to reassign (for example, PIP display (the main control your device. AUDIO). That mode key’s LED See “Programming Device OVERVIEW available) Exit any On-Screen whether the volume will change. If you Control”. display does not 1. Press and hold a device mode blinks three times and turns off, REW Rewind VCR, DVD, Display (OSD) and lock the remote's volume controls to Your new Motorola DRC800 universal change) key (AUDIO, DVD/VCR, or TV) for the TV (for example), you will always indicating that it has been 4-in-1 remote operates your Motorola VOD , DVR, or HTIB return to regular at least six seconds. The LED for reassigned. ADDITIONAL INFORMATION viewing be able to change the volume to the or or other manufacturer's cable set- PLAY Play VCR, DVD, VOD , each device key lights up, then level you want, without having to The reassigned key automatically uses PROGRAMMING DEVICE The Motorola DRC800 does not have top box and up to three other devices. DVR, or HTIB Display channel and the key for the device you adjust it on multiple devices. the same device code as the key you In addition, the DRC800 provides program information CONTROL selected remains on. selected in Step 1. If your second any user-serviceable parts. Opening 1. Press and hold the device mode the case, except for the battery cover, advanced features such as Digital FFWD Fast Forward VCR, 2. Press a function key (such as device uses a different code, you may Each of the additional device keys key (TV, AUDIO, DVD/VCR, or may cause permanent damage to your Video Recording (DVR) control and DVD, VOD , DVR, or Access the cable guide Power or Mute). The following Cable) corresponding to the program it for the new code. See controls a particular type of device. “Programming Device Control”. Motorola remote control. Picture-in-Picture (PIP) support. HTIB For example, the DVD/VCR key function keys are valid for device you want to control Searching (Power is volume for at least six seconds. Note: Cable No part of this publication may be You can lock volume control to any of RECORD Record to VCR or DVR Access any OSD for the controls your VCR, DVR, or DVD You may not reassign the these devices, to make adjusting your recommended): The LED for each device key reproduced, transmitted, transcribed, currently selected player, but not your TV, unless you device key to another type of device. home entertainment volume easier. specify otherwise. See “Reassigning •Power lights up, then the key for the stored in any retrieval system, or device translated to any language, in any See “Changing Volume Lock”. The PAUSE Device Keys”. device you selected remains on. Assigning a Key back to Its Original Pause VCR, DVD, VOD •Mute form, or by any means, electronic, DRC800 comes from the factory Move up through any or DVR ! 2. Press Volume +. Device Type: mechanical, optical, manual, or without the volume locked to any OSD or cable guide This device Controls this type of •Play The device key’s LED blinks three 1. Press and hold the device mode otherwise, without the prior written specific device. STOP Stop VCR, DVD, VOD menu key… device… •CH + times, indicating it has locked the key (TV, AUDIO, DVD/VCR, or permission of Motorola. You can also change what type of or DVR " Move down through TV TV •Stop volume control to the device you Cable) you want to reset to its MOTOROLA and the stylized M logo device each mode key controls. See any OSD or cable guide AUDIO original type (for example, Replay the previous DVD/VCR DVD, VCR, DVR, The device key’s LED blinks selected.