INSTALLATION INSTRUCTIONS for the Kodak ADAPTIVE PICTURE EXCHANGE (APEX) 26, 48, 74, and 122

INSTALLATION INSTRUCTIONS for the Kodak ADAPTIVE PICTURE EXCHANGE (APEX) 26, 48, 74, and 122

{InstallationInstructs}{Production}{KodakServiceSupport}{None} Publication No. II3337-2 10FEB09 INSTALLATION INSTRUCTIONS for the Kodak ADAPTIVE PICTURE EXCHANGE (APEX) 26, 48, 74, and 122 Important Qualified service personnel must install this equipment. 1 2 © EASTMAN KODAK COMPANY, 2009 KODAK SERVICE AND SUPPORT PLEASE NOTE The information contained herein is based on the experience and knowledge relating to the subject matter gained by Eastman Kodak Company prior to publication. No patent license is granted by this information. Eastman Kodak Company reserves the right to change this information without notice, and makes no warranty, express or implied, with respect to this information. Kodak shall not be liable for any loss or damage, including consequential or special damages, resulting from any use of this information, even if loss or damage is caused by Kodak’s negligence or other fault. This equipment includes parts and assemblies sensitive to damage from electrostatic discharge. Use caution to prevent damage during all service procedures. Table of Contents Description Page Safety. .4 Configurations . 5 Installing the Hardware . 6 Kodak ADAPTIVE PICTURE EXCHANGE 26 . 6 Installing the Components . 6 Completing the Installation of the Hardware . 8 Kodak ADAPTIVE PICTURE EXCHANGE 48 . 9 Installing the Components . 9 Installing the FOUR TRAY SORTERS . 10 Completing the Installation of the Hardware . 11 Kodak ADAPTIVE PICTURE EXCHANGE 74 . 12 Installing the Standard Components . 12 Installing the Optional Components . 17 Installing the PRINTERS . 19 Installing the FOUR TRAY SORTERS . 21 Installing the SKIRTS and Optional BACK PANEL ORGANIZERS . 22 Completing the Installation of the Hardware . 22 Kodak ADAPTIVE PICTURE EXCHANGE 122 . 23 Installing the Standard Components . 23 Installing the Optional Components . 23 Installing the PRINTERS . 23 Installing the FOUR TRAY SORTERS . 23 Installing the Second MAIN CABINET . 23 Installing the SKIRTS and Optional BACK PANEL ORGANIZERS . 24 Completing the Installation of the Hardware . 24 Installing and Configuring the Software . 25 Configuring Standard Settings on the APEX . 25 Configuring the Network on the APEX . 27 Configuring the Optional Settings on the APEX. 28 Print Options. 28 Kodak PICTURE MOVIE DVD . 28 Retailer CD. 29 Kodak PICTURE CD . 29 Kodak PRINT AT STORE . 30 Kodak REMOTE BUSINESS MANAGER . 30 MINILAB. 31 Configuring the Network Settings on the KIOSKS . 32 Configuring the Kiosk Network on the KIOSKS . 32 Configuring the Software on the KIOSKS . 33 2 10FEB09 – II3337-2 Checking the Operation of the Equipment . 34 Checking the Operation of the Equipment . 34 Making a Backup on the APEX. 34 Making a Backup on the KIOSKS. 34 Connections . 35 II3337-2 – 10FEB09 3 INSTALLATION INSTRUCTIONS Section 1: Safety This information defines the safety and information icons used in this publication. Caution This icon is used for conditions that could cause injury to a person, or damage to the equipment or software data. ESD Possible damage from electrostatic discharge. This icon is used for conditions that could cause damage to the equipment. Electrostatic discharge (ESD) is a primary source of: • equipment failure • equipment repairs A person cannot detect an electrical charge of less than 3,500 V, but 30 V can cause damage to components in the equipment. Preventive Measures • Check for an ESD WARNING LABEL before doing any procedure with ESD-sensitive components. All sensitive components have graphic LABELS that frequently include instructions. Use all label instructions. • Wear a GROUNDING STRAP when you touch ESD-sensitive components. Check that the CLIP remains fastened to a ground that has a clean surface with no paint. • Repair components in an ESD-protection area or use a PORTABLE GROUNDING MAT. • When moving ESD-sensitive components from area to area, insert and transport the components in the special material made for the transport of these components. Important This icon is used for important information. Note This icon is used for additional information. 4 10FEB09 – II3337-2 Configurations Section 2: Configurations Use the table below to guide you to the correct sections of this document for the configuration you are installing. Do only the procedures that are required for installation. See the retailer installation instructions or your region’s project support documentation for details. APEX 26 APEX 48 1. Do “Kodak ADAPTIVE PICTURE EXCHANGE Do “Kodak ADAPTIVE PICTURE EXCHANGE 26” on Page 6 - Page 8. 48” on Page 9 - Page 11. 2. Do “Installing and Configuring the Software” on Do “Installing and Configuring the Software” on Page 25 - Page 33. Page 25 - Page 33. 3. Do “Checking the Operation of the Equipment” Do “Checking the Operation of the Equipment” on Page 34. on Page 34. APEX 74 APEX 122 1. “Kodak ADAPTIVE PICTURE EXCHANGE 74” “Kodak ADAPTIVE PICTURE EXCHANGE on Page 12 - Page 22. 122” on Page 23 - Page 24. 2. Do “Installing and Configuring the Software” on Do “Installing and Configuring the Software” on Page 25 - Page 33. Page 25 - Page 33. 3. Do “Checking the Operation of the Equipment” Do “Checking the Operation of the Equipment” on Page 34. on Page 34. II3337-2 – 10FEB09 5 INSTALLATION INSTRUCTIONS Section 3: Installing the Hardware Kodak ADAPTIVE PICTURE EXCHANGE 26 Installing the Components [1] Loosen the KNOB on the right side STABILIZER FOOT. [2] Rotate the STABILIZER FOOT out. [3] Lower the STABILIZER FOOT so that it is level with the floor. [4] Tighten the KNOB. [5] Do Step 1 - Step 4 with the left side STABILIZER FOOT. KNOB STABILIZER FOOT A171_1058GCA A171_1058GC [6] Connect the 4 USB EXTENSION CABLES to the 4 USB EXTENSION USB PORTS on the front of the PROCESSOR. CABLES [7] Route the 4 USB EXTENSION CABLES to the back of the PROCESSOR. PROCESSOR USB PORTS A171_1108ACA A171_1108AC 6 10FEB09 – II3337-2 Installing the Hardware PROCESSOR MONITOR KEYBOARD CARD READER MOUSE LABEL PRINTER FILM SCANNER A171_1066GCA A171_1066GC [8] Install the components on the APEX 26. • PROCESSOR • MONITOR • KEYBOARD • MOUSE • CARD READER • PRINT SCANNER • FILM SCANNER - optional • LABEL PRINTER - optional [9] Install the PRINTERS to the APEX 26. [10] Connect the components and PRINTERS to the PROCESSOR. See “Connections” on Page 35. Important You must connect the POWER CORD for the F-135 FILM SCANNER to a power source outside the APEX. [11] Connect the POWER CORDS for the components to the POWER DISTRIBUTION BOX. [12] Install the SKIRTS (not shown) for the APEX 26. [13] Install the optional BACK PANEL ORGANIZER for the APEX 26. See the INSTALLATION INSTRUCTIONS included with the BACK PANEL ORGANIZER. II3337-2 – 10FEB09 7 INSTALLATION INSTRUCTIONS Completing the Installation of the Hardware PROCESSOR [1] Install the COVER for the PROCESSOR. COVER [2] Connect the NETWORK CABLE for the APEX to: • APEX • main network Caution Dangerous Voltage PROCESSOR [3] Connect the POWER CORDS from the CABINETS to the main power. [4] Turn on the main power switches for the CABINETS. A171_1067ACA [5] Load paper and ribbon into the PRINTERS. See A171_1067AC the User’s Guide. [6] Load labels into the LABEL PRINTER. See the User’s Guide. [7] Wait for the PRINTERS to display “Ready”. [8] Check that the lights on the FILM SCANNER illuminate green only. Note All of the lights on the FILM SCANNER might not be illuminated. [9] Advance to “Installing and Configuring the Software” on Page 25. 8 10FEB09 – II3337-2 Installing the Hardware Kodak ADAPTIVE PICTURE EXCHANGE 48 Installing the Components [1] Connect the 4 USB EXTENSION CABLES to the 4 USB EXTENSION USB PORTS on the front of the PROCESSOR. CABLES [2] Route the 4 USB EXTENSION CABLES to the back of the PROCESSOR. PROCESSOR USB PORTS A171_1108ACA A171_1108AC MONITOR [3] Install the components on the APEX 48. FILM CARD • PROCESSOR SCANNER READER KEYBOARD • MONITOR • KEYBOARD MOUSE • MOUSE • CARD READER • PRINT SCANNER • FILM SCANNER - optional • LABEL PRINTER - optional [4] Install the PRINTERS to the APEX 48. [5] Connect the components and PRINTERS to the PROCESSOR. See “Connections” on Page 35. Important You must connect the POWER CORD for the F-135 PROCESSOR FILM SCANNER to the power source outside the LABEL APEX. PRINTER A171_1063GCA [6] Connect the POWER CORDS for the components A171_1063GC to the POWER DISTRIBUTION BOX. [7] Install the SKIRTS (not shown) for the APEX 48. [8] Install the optional BACK PANEL ORGANIZER for the APEX 48. See the INSTALLATION INSTRUCTIONS for the BACK PANEL ORGANIZER. II3337-2 – 10FEB09 9 INSTALLATION INSTRUCTIONS Installing the FOUR TRAY SORTERS [1] Install the bottom FOUR TRAY SORTER. (a) Remove the 2 THUMBSCREWS from the DATA CABLE CABINET. (b) Use the 2 pins to position the FOUR TRAY SORTER. POWER (c) Install the 2 THUMBSCREWS. CABLE (d) Connect to the PPAC BOARD: • DATA CABLE • POWER CABLE FOUR TRAY SORTER A171_1039GCA A171_1039GC 2 THUMBSCREWS [2] Install the top FOUR TRAY SORTER. (a) Remove the 2 THUMBSCREWS from the CABINET. DATA CABLE (b) Use the 2 pins to position the FOUR TRAY SORTER. (c) Install the 2 THUMBSCREWS. (d) Connect to the PPAC BOARD: • DATA CABLE • POWER CABLE POWER CABLE FOUR TRAY SORTER A171_1040GCA 2 THUMBSCREWS A171_1040GC 10 10FEB09 – II3337-2 Installing the Hardware Completing the Installation of the Hardware PROCESSOR [1] Install the COVER for the PROCESSOR. COVER [2] Connect the NETWORK CABLE for the APEX to: • APEX • main network Caution Dangerous Voltage PROCESSOR [3] Connect the POWER CORDS from the CABINETS to the main power. [4] Turn on the main power switches for the CABINETS. A171_1067ACA [5] Load paper and ribbon into the PRINTERS. See A171_1067AC the User’s Guide. [6] Load labels into the LABEL PRINTER. See the User’s Guide. [7] Wait for the PRINTERS to display “Ready”. [8] Check that the lights on the FILM SCANNER illuminate green only. Note All of the lights on the FILM SCANNER might not be illuminated. [9] Advance to “Installing and Configuring the Software” on Page 25. II3337-2 – 10FEB09 11 INSTALLATION INSTRUCTIONS Kodak ADAPTIVE PICTURE EXCHANGE 74 Installing the Standard Components Installing the PROCESSOR [1] Loosen the KNOB on the right side STABILIZER FOOT.

View Full Text

Details

  • File Type
    pdf
  • Upload Time
    -
  • Content Languages
    English
  • Upload User
    Anonymous/Not logged-in
  • File Pages
    36 Page
  • File Size
    -

Download

Channel Download Status
Express Download Enable

Copyright

We respect the copyrights and intellectual property rights of all users. All uploaded documents are either original works of the uploader or authorized works of the rightful owners.

  • Not to be reproduced or distributed without explicit permission.
  • Not used for commercial purposes outside of approved use cases.
  • Not used to infringe on the rights of the original creators.
  • If you believe any content infringes your copyright, please contact us immediately.

Support

For help with questions, suggestions, or problems, please contact us