ALUMINUM ELECTROLYTIC CAPACITORS Snap-in Terminal Type, Withstanding Overvoltage series AD series Withstanding 3000 hours application of ripple current at 105°C. Suited for 100V/200V switch-over use in switching power supplies. Withstanding overvoltage and suited for IEC-60950 application. Withstandard AD overvoltage GU Specifications a Item Performance Characteristics Category Temperature Range – 40 ~ +105°C Rated Voltage Range 250V Rated Capacitance Range 82 ~ 1200µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current I 3 CV (µA) (After 5 minutes' application of rated voltage) [C:Rated Capacitance (µF), V:Voltage (V)] Rated voltage(V) 250 Measurement frequency:120Hz, Temperature:20°C tan δ tan δ (MAX.) 0.15 Rated voltage(V) 250 Measurement frequency:120Hz Stability at Low Temperature Z—25°C/Z+20°C 3 Impedance ratio ZT/Z20 (MAX.) Z—40°C/Z+20°C 12 After an application of DC voltage (in the range of rated DC voltage Capacitance change Within ±20% of intial value even after over-lapping the specified ripple current)for 3000 hours Endurance tan δ 200% or less of intial spesified value at 105°C, capacitors meet the characteristic requirements listed at Leakage current Initial specified value or less right. Capacitance change Within ±15% of intial value After leaving capacitors under no load at 105°C for 1000 hours, they Shelf Life tan δ 150% or less of intial spesified value meet the requirements listed at right. Leakage current Initial specified value or less Withstand excess voltage Not defective after 7 hours continuous charges of 360VDC at 70°C atmosphere. Marking Printed with white color letter on black sleeve. Drawing Type numbering system (Example : 250V 560µF) 1 2 3 4 5 6 7 8 9 10 11 12 Bottom plate Polarity bar (code HL only) Sleeve (P.E.T.) 0.8+0.2 L A D 2 E 5 6 1 M E L A ± -0.1 2-φ2.0 0.1 +0.2 0.8 -0.1 Case dia. code Configuration φD Code 0.5 ± +1MAX. Capacitance tolerance (±20%) 20 Y D 4.0 φ 2.5 22 Z 10± Rated Capacitance (560µF) 10 0.1 25 A L±2 Rated voltage (250V) +0.2 30 B ± 1.5-0.1 Pressure relief vent 4.0 0.5 Series name 35 C (PC board hole dimensions) (Terminal dimensions) Type The other terminal is also available upon request. Configuration Please refer page 197 for schematic of dimensions. Pb free lead finishing Sn-Pb lead finishing Pb free PET sleeve PVC sleeve contain Pb Without bottom plate With bottom plate EL HL Please contact to us if other configurations are required. Dimensions D × L (mm) V(Code) 250V (2E) φ Cap.(µF) Code D 20 22 25 30 35 0082 820 20 × 20 0.42 0100 101 20 × 25 0.53 22 × 20 0.53 0120 121 20 × 25 0.65 22 × 25 0.65 25 × 20 0.65 0150 151 20 × 30 0.79 22 × 25 0.79 25 × 25 0.79 0180 181 20 × 35 0.90 22 × 25 0.90 25 × 25 0.90 30 × 20 0.90 0220 221 20 × 40 1.00 22 × 30 1.00 25 × 25 1.00 30 × 25 1.00 0270 271 20 × 45 1.15 22 × 35 1.15 25 × 30 1.15 30 × 25 1.15 35 × 20 1.15 0330 331 20 × 50 1.30 22 × 40 1.30 25 × 35 1.30 30 × 25 1.30 35 × 25 1.30 0390 391 22 × 45 1.49 25 × 40 1.49 30 × 30 1.49 35 × 25 1.49 0470 471 25 × 45 1.65 30 × 35 1.65 35 × 25 1.65 0560 561 25 × 50 1.80 30 × 40 1.80 35 × 30 1.80 0680 681 30 × 45 2.00 35 × 35 2.00 0820 821 30 × 50 2.30 35 × 40 2.30 1000 102 35 × 45 2.47 1200 122 35 × 50 2.60 Rated Frequency coefficient of rated ripple current Case size ripple Frequency (Hz) 50 60 120 300 1k 10k 50k~ Coefficient 0.81 0.85 1.00 1.17 1.32 1.45 1.50 Rated Ripple (A rms) at 105°C 120Hz Minimum order quantity : 50pcs. CAT.8100S PLASTIC FILM CAPACITORS Metallized Polypropylene Film Capacitor AF series (Tape-wrapped Axial Type for High Frequency Applications) Non-inductive construction, with axial lead wires. Superior performance in high frequency circuit and charging / discharging circuit due to excellent characteristics of metallized polypropylene film dielectric. Highly reliable with self-healing property. Tape-wrapped and epoxy endfilled at both leads for superior mechanical strength and humidity resistance. Some A.C. applications may cause capacitor failure, over heating of the capacitors and / or discharge may be the result. Please contact us about details for A.C. application. Specifications Item Performance Characteristics Category Temperature Range –40 ~ +85˚C Rated Voltage 250, 400, 630V.D.C. Rated Capacitance Range 0.15 ~ 10µF Capacitance Tolerance ± 5% (J), ± 10% (K) Dielectric Loss Tangent 0.1% or less (at 1kHz 20˚C) Insulation Resistance C =< 0.33µF : 30000 MΩ or more C > 0.33µF : 10000 ΩF or more Between Terminals : Rated Voltage × 175%, 1 ~ 5 secs. Withstand Voltage Between Terminals and Coverage : Rated Voltage × 200%, 1 ~ 5 secs. Encapsulation Adhesive polyester film, resin Drawing Type numbering system (Example : 250V 1.5µF) 1 2 3 4 5 6 7 8 9 10 11 +1.5 Q A F 2 E 1 5 5 K R P +2.0 T –1.0 Configuration (RP:Polypropylene film, 35MIN W–1.0 35MIN Soldered CP wire) Capacitance tolerance (J : ±5% K : ±10%) Rated Capacitance (1.5µF) H ±1.5 Rated voltage (250V) φd ± 0.05 Series name Type Dimensions Unit : mm V(Code) 250VDC (2E) 400VDC (2G) 630VDC (2J) Cap. .(µF) Code Size TWH d TWH d TW H d 0.15 154 4.8 28.0 11.4 0.8 0.22 224 5.6 28.0 13.8 0.8 0.33 334 6.1 28.0 12.7 0.8 7.4 28.0 15.6 0.8 0.47 474 4.3 28.0 10.9 0.8 7.7 28.0 14.2 0.8 7.8 33.0 15.9 0.8 0.68 684 5.0 28.0 13.2 0.8 9.0 28.0 17.2 0.8 9.9 33.0 18.1 0.8 1.0 105 6.5 28.0 14.7 0.8 9.7 33.0 17.9 0.8 10.4 38.0 20.1 1.0 1.5 155 8.6 28.0 16.7 0.8 11.9 33.0 21.6 0.8 12.0 44.0 21.7 1.0 2.2 225 9.3 33.0 17.5 0.8 13.3 38.0 22.7 1.0 15.3 44.0 25.0 1.0 3.3 335 11.4 33.0 21.1 0.8 15.4 44.0 25.1 1.0 17.9 50.0 27.6 1.0 4.7 475 12.6 38.0 22.3 1.0 17.5 50.0 27.2 1.0 6.8 685 14.3 44.0 24.0 1.0 10.0 106 16.6 50.0 26.3 1.0 CAT.8100S ALUMINUM ELECTROLYTIC CAPACITORS Snap-in Terminal Type, Permissible Abnormal Voltage, Wide Temperature Range AK series Withstanding 2000 hours application of ripple current at 105°C. Extended voltage range at 200V, 400V and 420V. Improved safety features for abnormally excessive voltage. AK Ideally suited for the equipment used at voltage fluctuating area. Smaller AQ Specifications Item Performance Characteristics Category Temperature Range – 25 ~ +105°C Rated Voltage Range 200 • 400 • 420V Rated Capacitance Range 33 ~ 1200µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current I 3 CV (µA) (After 5 minutes' application of rated voltage) [C : Rated Capacitance (µF),V : Voltage(V)] tan δ 0.20MAX. 120Hz 20°C Rated voltage(V) 200 400 • 420 Stability at Low Temperature Measurement frequency : 120Hz Impedance ratio Z—25°C/Z+20°C 8 8 After an application of DC voltage (in the range of rated Capacitance change Within ±20% of initial value DC voltage even after over-lapping the specified ripple Endurance tan δ 200% or less of initial specified value current) for 2000 hours at 105°C, capacitors meet Leakage current Initial specified value or less the characteristic requirements listed at right. Capacitance change Within ±15% of initial value After leaving capacitors under no load at 105°C for 1000 Shelf Life tan δ 150% or less of initial specified value hours, they meet the requirements listed at right. Leakage current Initial specified value or less The pressure relief vent will operate in normal conditions, with no dangerous conditions such as flames, ignitions or dispersion of pieces of the capacitor and/or case. rating test conditions Voltage (V) Capacitance (µF) Limited DC current Test voltage 330 C < 330 4 A 200 330 C < 470 5 A 300VDC and 375VDC 470 C < 470 7 A Safety Performance 330 C < 100 2 A 400 100 C < 220 4 A 500VDC and 600VDC 220 C < 470 7 A 330 C < 100 2 A 420 100 C < 220 4 A 520VDC and 630VDC 220 C < 470 7 A Marking Printed with white color letter on dark blue sleeve Drawing Type numbering system (Example : 200V 680µF) Bottom plate Polarity bar (code BP only) Sleeve (P.V.C.) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 L A K 2 D 6 8 1 M H L A 5 0 Bottom Plate +1MAX.