ASSEMBLY GUIDE HD-5 Electronic Drum Kit EASY ASSEMBLY GUIDE IF YOU HAVE ANY QUESTIONS CALL OUR TOLL FREE HELPLINE 888-998-9848 DO NOT RETURN TO THE STORE UNBOXING YOUR DRUM KIT 1. Carefully unpack all contents of box (1) Crash Cymbal (1) Ride Cymbal (1) Hi-Hat Cymbal (1) Sound Module (3) Tom Drums (1) Snare Drum Kick Drum Kick Pedal Hi-Hat Control Pedal Drum Kit Components Cymbals Sound Module Module Mount Drum Frame Toms Kick Drum Mount Kick Drum Snare Cymbal Arms Not Pictured: Kick (1) Labeled Wiring Harness Pedal (1) Pair Headphones (1) Pair Drumsticks (1) Drumstick Holder Hi-Hat Control Pedal Feet Velcro Strips DRUM KIT ASSEMBLY 2. Attach the feet to the Drum Frame (fig.1) 3. Unfold the Drum Frame arms as shown (fig.2) (fig.2) (fig.1) 4. Attach the cymbal arms to the drum frame 5. Attach the cymbals to the cymbal arms as indicated positions .(fig.3) shown. Place the fin on the cymbal arm between the flanges on the cymbal as shown.(fig.4) HI-HAT CRASH RIDE (fig.4) (fig.3) DRUM KIT ASSEMBLY (CON’T) 6. Align the holes in Snare Drum Pad and the 7. Attach the Drum Pads in the positions three Tom Drum Pads and insert them into the hown below. (fig. 5) pole on the Drum Frame as shown. TOM TOM SNARE SNARE (fig.5) 8. Align the holes and attach the screws 9. Insert the rod of sound module stand into with the Drum Sound Module head the Drum Frame clamp as shown, then tight- and its stand as shown below. (fig. 6) en. (fig.7) BACK (fig.6) (fig.7) DRUM KIT ASSEMBLY (CON’T) 10. Attach the kick drum to the kick drum 11. Assemble the kick drum pedal by inserting brace as shown below. (fig.8) the two chrome metal rods into the kick drum pedal frame as shown below . (fig.9) (fig.8) (fig.9) 12. Attach the kick drum pedal mallet to the 13. Insert the tongue of the kick drum into the clamp of the kick drum pedal. (fig.12) Tighten clamp on the ped- kick drum pedal by insertIng and attaching as al until the kick drum and pedal are securely fastened. shown below. (fig.10& 11) (fig.13) (fig.10) (fig.11) (fig.12) (fig.13) DRUM KIT ASSEMBLY (CON’T) 14. Check the surface pads on the bottom of the 15. Place the hi-hat control pedal on the hi-hat control pedal. The pads may be used on ground by the hi-hat cymbal. (fig.15) either carpet or hard flooring.(fig.14) (fig. 14) CARPET PEEL HARD FLOORING (fig. 15) DRUM KIT WIRING DIAGRAM 16. Connect the wiring harness to the interface at the bottom of the drum sound module, then connect the labeled cables to their corresponding drum pads, cymbals and pedals, as show below. Drum Module Connector Panel POWER OFF ON USB TRIGGER HEADPHONE control module DC 9V LINE OUT LINE IN ride tom 3 tom 2 tom 1 POWER OFF ON USB TRIGGER HEADPHONE DC 9V LINE OUT LINE IN crash plug into “trigger” hi-hat cable snake to drumset snare high-hat control kick DRUM THRONE ASSEMBLY 17. Extend the drum throne legs and secure the legs with the wingut. (fig 16) Fasten the drum throne stool to the height adjustment rod and secure the stool with the wingnut. (fig 17) Set up the drum throne at the desired height as shown below. (fig 18) (fig. 18) (fig. 13)16) (fig. 17) FINAL STEPS 18. Attach Drumstick Pouch (fig 19)to drum frame as shown. (fig 20) (fig 20) (fig 19) 19. Please use the included Velcro Strips to attach 20. Attach the included power supply adapter the wiring harness to the drum frame. This will help to make the wiring harness neat and orderly and the headphones to drum sound module against the drum frame. connector panel. POWER velcro OFF ON USB TRIGGER HEADPHONE DC 9V LINE OUT LINE IN drum frame If you have any questions about your drum kit please contact us toll free 888-998-9848 Virgin (VMI) is the Parent Company of Hitman Drums Virgin Musical Instrument Company PO BOX 2908 LA MESA, CA 91943 [email protected] www.virginmusicalinstruments.com.