Sunbeam MultiMincer® Instruction and Recipe Booklet FG5600 Please read these instructions carefully and retain for future reference. Contents Sunbeam’s Safety Precautions 3 Features of your Sunbeam MultiMincer® 4 Attachments for your Sunbeam MultiMincer® 6 Using your Sunbeam MultiMincer® 7 Storing your Sunbeam MultiMincer® 10 Handy Hints for Mincing 11 Handy Hints for Sausage Making 12 Care and Cleaning 13 Recipes 14 Important instructions – retain for future use. Sunbeam’s Safety Precautions SAFETY PRECAUTIONS FOR YOUR • Do not contact moving parts at all times. SUNBEAM MULTIMINCER. • Do not put hot meat into the mincer. • Always use extreme care when handling the • All discs and attachments should be removed blade and discs. with care before cleaning. • Unplug from power outlet when not in use, • Only use the attachments and accessories before putting on or taking off attachments, provided and recommended by Sunbeam. and before cleaning. • Do not overload the mincer. • Only use the pusher that is supplied with this • Do not operate for more than 1 minute at a mincer. time while mincing heavy loads. This does not • Do not put your fingers or any utensil into the apply to any of the recipes in this booklet. feeder chute. Sunbeam is very safety conscious when • Do not use an appliance for any purpose designing and manufacturing consumer products, other than its intended use. but it is essential that the product user also • Do not place an appliance on or near a hot gas exercise care when using an electrical appliance. flame, electric element or on a heated oven. Listed below are precautions which are essential • Do not place on top of any other appliance. for the safe use of an electrical appliance: • Do not let the power cord of an appliance hang • Read carefully and save all the instructions over the edge of a table or bench top or touch provided with an appliance. any hot surface. • Always turn the power off at the power outlet • Do not operate any electrical appliance with before you insert or remove a plug. Remove a damaged cord or after the appliance has by grasping the plug - do not pull on the cord. been damaged in any manner. If damage is • Turn the power off and remove the plug suspected, return the appliance to the nearest when the appliance is not in use and Sunbeam Appointed Service Centre before cleaning. for examination, repair or adjustment. • Do not use your appliance with an extension • For additional protection, Sunbeam cord unless this cord has been checked recommend the use of a residual current and tested by a qualified technician or device (RCD) with a tripping current not service person. exceeding 30mA in the electrical circuit • Always use your appliance from a power supplying power to your appliances. outlet of the voltage (A.C. only) marked • Do not immerse the appliance in water on the appliance. or any other liquid unless recommended. • This appliance is not intended for use by • Appliances are not intended to be operated persons (including children) with reduced by means of an external timer or separate physical, sensory or mental capabilities, or remote control system. lack of experience and knowledge, unless they • This appliance is intended to be used in have been given supervision or instruction household and similar applications such concerning use of the appliance by a person as: staff kitchen areas in shops, offices and responsible for their safety. other working environments; farm houses; by • Children should be supervised to ensure that clients in hotels, motels and other residential they do not play with the appliance. type environments; bed and breakfast type • The temperature of accessible surfaces may be environments. high when the appliance is operating. • Never leave an appliance unattended while in use. If you have any concerns regarding the performance and use of your appliance, please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line. Ensure the above safety precautions are understood. 3 Features of your Sunbeam MultiMincer® Feeder tray Use the Feeder Tray to hold food ready for mincing. Mincer body Houses the powerful 600 watt motor. (1500W Locked Rotar). Delivers high torque at low speeds to grind and mince through the toughest meat cuts. Non-slip rubber feet Makes the unit sturdy, preventing it from slipping or scratching the benchtop. 4 Food pusher Guides meat safely through the chute to hit the mincing screw, for superior mincing results. Chute The chute houses the mincing screw and blade. Use the food pusher to direct food through the chute to the mincing screw and blade. Mincing screw Blade Mincing discs (Fine, Medium and Coarse) Fastening dial Locks the mincing discs, sausage and kebbe attachments firmly into place. Use the spanner to ensure it is firmly screwed onto the chute. Food catcher Place underneath chute for mince and sausage collection. Also doubles as a storage unit to store attachments – use the feeder tray as the lid. 5 HeadingAttachments for your Sunbeam MultiMincer® Fine disc Sausage making attachment (Thick nozzle, thin nozzle, base plate) Medium disc Coarse disc Feeder tray Cleaning disc Food catcher Kebbe making attachments (Kebbe cone, kebbe shaper) Spanner 6 Using your Sunbeam MultiMincer® Before using your Mincer 6. Align chute into the mincer body, using Wash all attachments in warm soapy water arrows as a guide. Press and hold the using a mild detergent. Dry each part lock/unlock button to twist and lock into thoroughly before use. place. Before you assemble the mincer ensure that 7. Once the mincer body is in place, tighten the power cord is unplugged. the fastening dial using the spanner to NOTE: All attachments must be firmly in ensure all elements are securely in place. place before using the appliance. Ensure that See figure 2. the mincing screw and blade are firmly in 8. Place the food catcher underneath the place inside the mincer body and the mincer fastening dial for mince collection and discs or sausage maker attachments are the feeder tray on top of the mincer secured with the fastening dial. chute. See figure 2. Figure 2 Fitting and using the mincing discs 1. Place the mincer body, facing you on a level, dry surface. 2. Fit the mincing screw inside the chute. 3. Fit the blade over the mincing screw ensuring that the flat side of the blade (with the letter ‘B’) faces the mincing screw, away from the mincing disc. 4. Fit the disc (depending on the type of mince your require, this will either be a fine, medium or coarse disc). 5. The fastening dial then fits over the disc and screws into place. Do not tighten this fastening dial yet as it will be harder to 9. Place prepared meat in feeder tray. Plug lock into the mincer body. See Fig 1. the power cord into a 230-240V AC power outlet and turn the power ‘ON’. 10.Switch the mincer on by pressing ‘ON’ Figure 1 button. Using the food pusher, gently push meat through the chute. NOTE: Do not use excessive force to push meat through the mincing chute as it could damage the appliance. CAUTION: Do not use anything else apart from the pusher supplied with this mincer to push meat through the chute. NEVER use your hands/fingers to push meat through the chute. 7 Using your Sunbeam MultiMincer® (continued) Fitting and using the Sausage attachments 7. Tighten the fastening dial using the 1. Place the mincer body, facing you on a spanner to ensure all elements are level, dry surface. securely in place. 2. Fit the mincing screw inside the Chute. 8. Place the food catcher underneath the fastening dial for sausage collection and 3. Fit the base plate over the mincing screw, place the feeder tray on top of the chute. so the dome is facing outwards. See Fig 4. 4. Fit either the thick or thin sausage nozzle over the base plate Figure 4 5. While holding the sausage nozzle in place, screw the fastening dial over the nozzle and loosely secure by screwing on the fastening dial. See Figure 3. Figure 3 9. If using fresh sausage skins, soak it in cold water for approximately 30 minutes before using on the nozzle attachment. 10. Plug the power cord into a 230-240V AC power outlet and turn the power ‘ON’. 11. Switch on mincer. 6. Align chute into the mincer body using 12. Using the pusher, push the sausage arrows as a guide. Press the lock/unlock mixture into the chute. button and twist to lock into place. 13. As the mixture comes through the nozzle, ease the skin off as it fills. Twist the skin at the desired length to form individual sausages once all of the casings are filled. See tips on sausage making on page 12 for further information on sausage making. 8 Using your Sunbeam MultiMincer® (continued) Fitting and using the Kebbe attachments 7. Place the feeder tray on top of the chute. 1. Place the mincer body, facing you on a See Fig 6. level, dry surface. 2. Fit the mincing screw inside the chute. Figure 6 3. Fit the kebbe shaper. 4. Fit the kebbe cone over the shaper. 5. Secure the kebbe attachments with the fastening dial. Loosely secure with fastening dial – do not use spanner until chute is locked into mincer body. See figure 5. Figure 5 8. Plug the power cord into a 230-240V AC power outlet and turn the power ‘ON’. 9. Switch on mincer. 10. Using the pusher, push the kebbe mixture into the chute. 11. Cut kebbe into desired lengths. Tip: For full kebbe recipe and suggestions see page 20.