<p>Lab #2</p><p>Router 1: Login and Hostname Setup</p><p>Username: lab</p><p>Password:</p><p>Router1>enable</p><p>Password:</p><p>Router1#config t</p><p>Enter configuration commands, one per line. End with CNTL/Z.</p><p>Router1(config)#hostname r1-libert76-Dand04</p><p>#1</p><p>Router 1: Gig0/0 Setup r1-libert76- Dand04# Dand t</p><p>Enter configuration commands, one per line. End with CNTL/Z. r1-libert76- Dand04(config)#int gi0/0 r1-libert76- Dand04(config-if)#ip add 192.168.10.1 255.255.255.0 r1-libert76- Dand04(config-if)#description link to sw1 r1-libert76- Dand04(config-if)#no shut</p><p>Router 1: Show CDP Neighbor r1-libert76- Dand04(config)#exit r1-libert76- Dand04#show cdp neighbor</p><p>Device ID Local Intrfce Holdtme Capability Platform Port ID</p><p>Switch1 Gig0/0 147 S I WS-C295-24 Fas 0/20</p><p>#2</p><p>Switch 1: Login and Hostname Setup</p><p>Username: lab</p><p>Password: switch1>enable</p><p>Password:</p><p>Password: switch1#conf t</p><p>Enter configuration commands, one per line. End with CNTL/Z. switch1(config)#hostname sw1-libert76- Dand04 sw1-libert76- Dand04(config)#</p><p>#3</p><p>Switch 1: VLAN 1 Setup sw1-libert76- Dand04(config)#int vlan 1 sw1-libert76- Dand04(config-if)#ip add 192.168.10.2 255.255.255.0 sw1-libert76- Dand04(config-if)#no shut sw1-libert76- Dand04(config-if)#exit sw1-libert76- Dand04(config)#exit sw1-libert76- Dand04#show int vlan1 #4</p><p>Router – Switch Ping Test</p><p>Username: lab</p><p>Password: r1-libert76- Dand04>enable</p><p>Password: r1-libert76- Dand04#ping 192.168.10.2</p><p>Type escape sequence to abort.</p><p>Sending 5, 100-byte ICMP Echos to 192.168.10.2, timeout is 2 seconds:</p><p>!!!!!</p><p>Success rate is 100 percent (5/5), round-trip min/avg/max = 3/9/15 ms</p><p>#5</p><p>Router 1: Show IP Route</p><p>R1-libert76- Dand04#show ip route</p><p>#6</p><p>Switch 1: VLAN 5 Setup sw1-libert76- Dand04#vlan data sw1-libert76- Dand04(vlan)#vlan 5 name accounting sw1-libert76- Dand04(vlan)#vtp transparent sw1-libert76- Dand04(vlan)#exit sw1-libert76- Dand04#conf t</p><p>Enter configuration commands, one per line. End with CNTL/Z. sw1-libert76- Dand04(config)#int fa 0/20 sw1-libert76- Dand04(config-if)#switchport access vlan 5 sw1-libert76- Dand04(config-if)#</p><p>#7</p><p>Switch 1: Trunk Mode sw1-libert76- Dand04#conf t</p><p>Enter configuration commands, one per line. End with CNTL/Z. sw1-libert76- Dand04(config)#int fa0/20 sw1-libert76- Dand04(config-if)#switchp mode trunk sw1-libert76- Dand04(config-if)#exit sw1-libert76- Dand04(config)#exit sw1-libert76- Dand04#ping 192.168.10.1</p><p>Type escape sequence to abort.</p><p>Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds:</p><p>!!!!!</p><p>Success rate is 100 percent (5/5), round-trip min/avg/max = 2/8/13 ms</p><p>#8</p><p>Router 1: IP Route and Ping r1-libert76- Dand04#ping 192.168.10.2</p><p>Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.10.2, timeout is 2 seconds:</p><p>!!!!!</p><p>Success rate is 100 percent (5/5), round-trip min/avg/max = 1/7/10 ms r1-libert76- Dand04#show ip route</p><p>Gateway of last resort is not set</p><p>C 192.168.10.0 is directly connected, GigabitEthernet0/0</p><p>#9</p><p>Router 2: Login and Initial Config</p><p>Username: lab</p><p>Password: router2>enable</p><p>Password: router2#conf t</p><p>Enter configuration commands, one per line. End with CNTL/Z. router2(config)#hostname r2-libert76- Dand04 r2-libert76- Dand04(config)#int fa0/0 r2-libert76- Dand04(config-if)#ip add 192.168.20.1 255.255.255.0 r2-libert76- Dand04(config-if)#no shut</p><p>#10</p><p>Router 2: Serial Link Setup r2-libert76- Dand04(config-if)#exit r2-libert76- Dand04(config)#int s0/0/1 r2-libert76- Dand04(config-if)#ip add 10.0.3.2 255.255.255.252 r2-libert76- Dand04(config-if)#description serial link to router 1 r2-libert76- Dand04(config-if)#no shut</p><p>#11</p><p>Router 1: Serial Link Setup r1-libert76- Dand04(config)#int s1/1 r1-libert76- Dand04(config-if)#ip add 10.0.3.1 255.255.255.252 r1-libert76- Dand04(config-if)#description serial link to router 2 r1-libert76- Dand04(config-if)#no shut</p><p>#12</p><p>Router 1: IP Route r1-libert76- Dand04#show ip route</p><p>#13</p><p>Router 2: Static Route and Ping r2-libert76- Dand04#conf t</p><p>Enter configuration commands, one per line. End with CNTL/Z. r2-libert76- Dand04(config)#ip route 0.0.0.0 255.255.255.255 10.0.3.1 r2-libert76- Dand04(config)#exit r2-libert76- Dand04#ping 192.168.10.2</p><p>#14 Switch 2: Setup switch2#conf t</p><p>Enter configuration commands, one per line. End with CNTL/Z. switch2(config)#hostname sw2-libert76- Dand04 sw2-libert76- Dand04(config)#int vlan 1 sw2-libert76- Dand04(config-if)#ip add 192.168.20.2 255.255.255.0 sw2-libert76- Dand04(config-if)#no shut</p><p>#15</p><p>Router 1: Static Route Setup</p><p>Username: lab</p><p>Password: r1-libert76- Dand04>enable</p><p>Password: r1-libert76- Dand04#conf t</p><p>Enter configuration commands, one per line. End with CNTL/Z. r1-libert76- Dand04(config)#ip route 0.0.0.0 255.255.255.255 10.0.3.2 r1-libert76- Dand04(config)#exit r1-libert76- Dand04#show ip route</p><p>#16</p><p>Router 2: IP Route r2-libert76- Dand04#show ip route #17</p><p>Gateway: Setup gateway#conf t gateway(config)#hostname gw-libert76- Dand04 gw-libert76- Dand04(config)#int s4/0 gw-libert76- Dand04(config-if)#ip add 10.0.1.1 255.255.255.252 gw-libert76- Dand04(config-if)#description serial link to router 1 gw-libert76- Dand04(config-if)#no shut gw-libert76- Dand04(config-if)#exit gw-libert76- Dand04(config)#int s4/1 gw-libert76- Dand04(config-if)#ip add 10.0.2.1 255.255.255.252 gw-libert76- Dand04(config-if)#description serial link to router 2 gw-libert76- Dand04(config-if)#no shut gw-libert76- Dand04(config-if)# gw-libert76- Dand04(config-if)#exit gw-libert76- Dand04(config)#exit gw-libert76- Dand04#show cdp neighbors</p><p>#18</p><p>Router 1: OSPF Setup and IP Route r1-libert76- Dand04(config)#router ospf 100 r1-libert76- Dand04(config-router)#network 10.0.1.0 0.0.0.3 area 0 r1-libert76- Dand04(config-router)#exit r1-libert76- Dand04(config)#exit r1-libert76- Dand04#show ip route</p><p>#19</p><p>Switch 1: Trace Route sw1-libert76- Dand04>tracero 192.168.20.2</p><p>#20</p><p>Router 1: OSPF r1-libert76- Dand04#conf t</p><p>Enter configuration commands, one per line. End with CNTL/Z. r1-libert76- Dand04(config)#ro ospf 100 r1-libert76- Dand04(config-router)#net 10.0.3.0 0.0.0.3 area 0</p><p>#20.1</p><p>Gateway: Show Route gw-libert76- Dand04#sho ip ro</p><p>#21 Router 2: OSPF Inter-area Setup r2-libert76- Dand04#conf t</p><p>Enter configuration commands, one per line. End with CNTL/Z. r2-libert76- Dand04(config)#ro ospf 100 r2-libert76- Dand04(config-router)#no net 192.168.20.0 0.0.0.255 area 0 r2-libert76- Dand04(config-router)#net 192.168.20.0 0.0.0.255 area 1</p><p>#22</p><p>Router 2: Running Config r2-libert76- Dand04#sho run</p><p>Building configuration...</p><p>Current configuration : 3357 bytes</p><p>! version 12.4 service timestamps debug uptime service timestamps log uptime no service password-encryption</p><p>! hostname r2-libert76- Dand 04</p><p>! no logging buffered</p><p>! boot system flash slot0: enable password enable123 ! username lab password 0 lab123</p><p>!</p><p>! ip subnet-zero</p><p> ip cef</p><p>!</p><p>!</p><p>! ip ssh time-out 120 ip ssh authentication-retries 3</p><p>!</p><p>!</p><p>!</p><p>!</p><p>!</p><p>! crypto mib ipsec flowmib history tunnel size 200 crypto mib ipsec flowmib history failure size 200</p><p>!</p><p>!</p><p>! fax interface-type modem mta receive maximum-recipients 0</p><p>!</p><p>!</p><p>!</p><p>! interface BRI0/1</p><p> description 0</p><p> bandwidth 16</p><p> no ip address</p><p>! interface BRI0/1:1</p><p> description 0</p><p> bandwidth 64</p><p> no ip address</p><p> encapsulation hdlc</p><p>! interface BRI0/1:2</p><p> description 0</p><p> bandwidth 64</p><p> no ip address encapsulation hdlc</p><p>! interface FastEthernet0/0</p><p> bandwidth 100000</p><p> ip address 192.168.20.1 255.255.255.0</p><p> full-duplex</p><p>! interface FastEthernet0/1</p><p> bandwidth 100000</p><p> no ip address</p><p> shutdown</p><p>! interface Null0</p><p> bandwidth 4294967</p><p> no ip address</p><p> encapsulation isl</p><p>! interface Serial0/0/0</p><p> description serial link to gw</p><p> bandwidth 1544</p><p> ip address 10.0.2.2 255.255.255.252</p><p> encapsulation hdlc ! interface Serial0/0/1</p><p> description serial link to router 1</p><p> bandwidth 1544</p><p> ip address 10.0.3.2 255.255.255.252</p><p> encapsulation hdlc</p><p>! vlan database</p><p> vlan 1 name default</p><p> vlan 1002 name fddi-default</p><p> vlan 1003 name token-ring-default</p><p> vlan 1004 name fddinet-default</p><p> vlan 1005 name trnet-default</p><p>! router ospf 100</p><p> network 10.0.2.0 0.0.0.3 area 0</p><p> network 10.0.3.0 0.0.0.3 area 0</p><p> network 192.168.20.0 0.0.0.255 area 1</p><p>!</p><p>!</p><p>!</p><p>! ip default-gateway 0.0.0.0 ip classless ip route 0.0.0.0 255.255.255.255 10.0.3.1 ip http server</p><p>! ip pim bidir-enable logging traps debugging</p><p>!</p><p>! snmp-server engineID local 0000009020000029BA3CF0 snmp-server community public RO snmp-server community private RW snmp-server packetsize 4500 call rsvp-sync</p><p>!</p><p>!</p><p>!</p><p>! line con 0</p><p> exec-timeout 10 0</p><p> login line aux 0</p><p> exec-timeout 10 0 line vty 0 4</p><p> exec-timeout 10 0</p><p> login</p><p>!</p><p>! end</p>