Masterstream Nozzle Series INSTRUCTIONS FOR INSTALLATION, OPERATION, AND MAINTENANCE Understand manual before use. Operation of this device without understanding the manual and WARNING receiving proper training is a misuse of this equipment. Obtain safety information at tft.com/serial- number. This equipment is intended for use by trained and qualified emergency services personnel for firefighting. All personnel using this equipment shall have completed a course of education approved by the Authority Having Jurisdiction (AHJ). This instruction manual is intended to familiarize firefighters and maintenance personnel with the operation, servicing, and safety procedures associated with this product. This manual should be kept available to all operating and maintenance personnel. MASTERSTREAM 1000 MASTERSTREAM 1250S 150 - 1000 GPM @ 100 PSI 150 - 1250 GPM @ 100 PSI 600 - 4000 L/min @ 7 BAR (700 kPa) 600 - 4500 L/min @ 7 BAR (700 kPa) MASTERSTREAM 1250 MASTERSTREAM 1500 300 - 1250 GPM @ 70 - 120 PSI 300 - 1500 GPM @ 70 - 120 PSI 1100 - 4700 L/min @ 4.8 - 8.3 BAR (480 - 830 kPa) 1100 - 5700 L/min @ 4.8 - 8.3 BAR (480 - 830 kPa) MASTERSTREAM 2000 MASTERSTREAM 4000 300 - 2000 GPM @ 80 - 120 PSI 600 - 4000 GPM @ 80 - 120 PSI 1100 - 7600 L/min @ 5.5 - 8.3 BAR (550 - 830 kPa) 2300 - 15000 L/min @ 5.5 - 8.3 BAR (550 - 830 kPa) TASK FORCE TIPS LLC 3701 Innovation Way, Valparaiso, IN 46383-9327 USA MADE IN USA · tft.com 800-348-2686 · 219-462-6161 · Fax 219-464-7155 ©Copyright Task Force Tips LLC 1999-2020 1 LIM-030 November 16, 2020 Rev15 SUPPORTING MATERIALS The following documents contain supporting safety and operating information pertaining to the equipment described in this manual. NOZZLE TRAJECTORY ELEVATION FACTORS Reach Factor (compared to 30° elevation) 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 3.5 85° 75° 3.0 IF TARGET IS IN THIS REGION, 2.5 FLOW AND/OR PRESSURE MUST 60° BE INCREASED. 2.0 45° 1.5 1.0 red to 30° elevation) 30° height of discharge 0.5 15° 0.0 -0.5 Height Factor (compa -1.0 -1.5 - -45° - -30° - -15° - 0° -2.0 Stream reach and height at non-optimal elevations can be estimated as a factor of the performance at the optimal 30° elevation. Refer to LIM-030 and LIM-035 for effective stream trajectories of Task Force Tips Masterstream nozzles at 30° elevation. This graph cannot be used to estimate maximum reach for elevation angles below 30°. 1.0 To estimate elevation angle when vertical and horizontal distances to target are known: 1.1 Find the maximum height and reach at 30° from the appropriate trajectory curve in LIM-030 or LIM-035. 1.2 Calculate the Height Factor by dividing the vertical distance to the target by maximum height from step 1.1. 1.3 Calculate the Reach Factor by dividing the horizontal distance to the target by maximum reach from step 1.1. 1.4 On the graph of nozzle trajectory elevation factors, plot the intersection of the Height Factor and Reach factor from steps 1.2 and 1.3. If this point lies on or between the curves given, estimate the appropriate elevation angle. If this point lies within the shaded region of the graph, then a higher ÀRZ or pressure must be used to reach the target. 2.0 To estimate maximum reach for a given elevation angle above 0°: 2.1 From the graph of nozzle trajectory elevation factors, choose the trajectory curve for the desired elevation angle. 2.2 Find the point where this trajectory curve intersects the height of discharge (zero height line). 2.3 Estimate the Reach Factor at this point using the scale across the top of the graph. 2.4 Multiply this Reach Factor by the reach at 30° elevation from the appropriate trajectory curve in LIM-030 or LIM-035. 3.0 To estimate maximum height for a given elevation angle above 0°: 3.1 From the graph of nozzle trajectory elevation factors, choose the trajectory curve for the desired elevation angle. 3.2 Find the maximum height on this trajectory curve. 3.3 Estimate the Height Factor at the maximum height using the scale on the left side of the graph. 3.4 Multiply this Height Factor by the height at 30° elevation from the appropriate trajectory curve in LIM-030 or LIM-035. TASK FORCE TIPS, INC. 3701 Innovation Way, Valparaiso, IN 46383-9327 USA MADE IN USA • www.tft.com 800-348-2686 • 219-462-6161 • Fax 219-464-7155 ©Copyright Task Force Tips, Inc. 2009 LTT-135 July 28, 2009 Rev00 LIA-025 LTT-135 Manual: Foam Aspirators Nozzle Trajectory Elevation Factors TASK FORCE TIPS ELECTRIC REMOTE NOZZLES MANUAL: Remote Control (RC) ELECTRIC REMOTE WIRING DIAGRAM Monitor Electrical Controls Supplemental Instructions for use with RC Monitor Manual INSTRUCTIONS FOR INSTALLATION, SAFE OPERATION AND MAINTENANCE Understand manual before use. Operation of this device without understanding the manual and DANGER receiving proper training is a misuse of this equipment. Obtain safety information at www.tft. com/serial-number SECTION 3.0 SECTION 4.9 Toggle Switch Monitor Operator Station SECTION 4.0 (Y4E-TS) Electrical Controls Installation and Operation SECTION 4.10 SECTION 4.1 Monitor Communication Monitor Mounted Interface Control Operator Station (Y4E-COMM) SECTION 4.2 SECTION 4.11 Panel Mount Monitor Position Display Operator Station (Y4E-DISP) (Y4E-RP) SECTION 4.3 SECTION 4.12 Remote Auxiliary Function Panel Mount With Display Interface Control Operator Station (YE-REMAUX) (Y4E-RP-D) LESS ELABORATE WIRING SECTION 4.4 SECTION 4.13 SYSTEMS MAY BE USED BY Tethered Electric RC Monitor Aerial ELIMINATING UPPER CONTROL Operator Station Truck Installation OR REMOTE CONTROL STATIONS (Y4E-CT-##) SECTION 4.14 SECTION 4.5 Multiplex Interface Control (YE-CAN#) Tethered Operator Station With Display (Y4E-CT-##-D) SECTION 4.15 Ethernet Interface Control SECTION 4.6 Wireless Operator Station (YE-RF-##) SECTION 4.16 Electric Nozzle Actuator SECTION 4.7 Wireless Operator Station With Display (YE-RF-##-D) SECTION 4.17 Valve Kits SECTION 4.8 (YE-VK-PH) Joystick Operator Station SECTION 5.0 (Y4E-JS) Troubleshooting TASK FORCE TIPS LLC 3701 Innovation Way, IN 46383-9327 USA 800-348-2686 • 219-462-6161 • Fax 219-464-7155 TASK FORCE TIPS LLC 3701 INNOVATION WAY, VALPARAISO, IN 46383-9327 MADE IN USA • tft.com MADE IN USA • TFT.COM (800) 348-2686 (219) 462-6161 FAX (219) 464-7155 ©Copyright Task Force Tips LLC 2008-2019 LIY-500 April 8, 2019 Rev14 ©Copyright Task Force Tips LLC 1998-2018 LIM-040 August 1, 2018 Rev05 LIM-040 LIY-500 ER Nozzle Wiring Guide Manual: Remote Control (RC) Monitor Electrical Controls ©Copyright Task Force Tips LLC 1999-2020 2 LIM-030 November 16, 2020 Rev15 TABLE OF CONTENTS 1.0 MEANING OF SAFETY SIGNAL WORDS 2.0 SAFETY 3.0 GENERAL INFORMATION 3.1 VARIOUS MODELS AND TERMS 3.2 SPECIFICATIONS 3.3 NOZZLE COUPLINGS 3.4 USE WITH SALT WATER 3.5 HYDRAULIC INSTALLATION 3.6 ELECTRIC INSTALLATION 4.0 FLOW CHARACTERISTICS 4.1 MASTERSTREAM 1000 & 1250S (AUTOMATIC) 4.2 MASTERSTREAM 1250, 1500, 2000, & 4000 (AUTOMATIC) 4.3 MASTERSTREAM 1000 (SELECTABLE) 4.4 MASTERSTREAM 1000 (FIXED) 4.5 REACH AND TRAJECTORY 5.0 OPERATION 5.1 PATTERN CONTROL 5.2 FLUSHING DEBRIS 6.0 USE WITH FOAM 6.0.1 FOAMJET LX WITH MASTERSTREAM 1000 AND 1250S NOZZLE 7.0 WARRANTY 8.0 MAINTENANCE 8.1 FIELD LUBRICATION 8.2 SERVICE TESTING 8.3 REPAIR 9.0 EXPLODED VIEWS AND PARTS LISTS 10.0 OPERATION AND INSPECTION CHECKLIST DANGER PERSONAL RESPONSIBILITY CODE The member companies of FEMSA that provide emergency response equipment and services want responders to know and understand the following: 1. Fire¿ ghting and Emergency Response are inherently dangerous activities requiring proper training in their hazards and the use of extreme caution at all times. 2. It is your responsibility to read and understand any user’s instructions, including purpose and limitations, provided with any piece of equipment you may be called upon to use. 3. It is your responsibility to know that you have been properly trained in Fire¿ ghting and /or Emergency Response and in the use, precautions, and care of any equipment you may be called upon to use. 4. It is your responsibility to be in proper physical condition and to maintain the personal skill level required to operate any equipment you may be called upon to use. 5. It is your responsibility to know that your equipment is in operable condition and has been maintained in accordance with the manufacturer’s instructions. 6. Failure to follow these guidelines may result in death, burns or other severe injury. FEMSA Fire and Emergency Manufacturers and Service Association P.O. Box 147, Lynn¿ eld, MA 01940 • www.FEMSA.org ©Copyright Task Force Tips LLC 1999-2020 3 LIM-030 November 16, 2020 Rev15 1.0 MEANING OF SAFETY SIGNAL WORDS A safety related message is identified by a safety alert symbol and a signal word to indicate the level of risk involved with a particular hazard. Per ANSI Z535.6, the definitions of the four signal words are as follows: DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious WARNING injury. CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor CAUTION or moderate injury. NOTICE NOTICE is used to address practices not related to physical injury.