Invented and Developed in Australia by Sean Pepper

Invented and Developed in Australia by Sean Pepper

Combination Square 400mm Vertical and Horizontal Level Bench-top Level Marks any angle Finds any angle from one given surface Level to achieve any given angle Digital level equivalent Works out Mitre Joins Marking Gauge… Multi-purpose carpenters’ and builders’ square Invented and developed in Australia by Sean Pepper The American standard roofus Consists of a 15 inch rule in sixteenths and a degree scale ending at 55 degrees in both angle directions from the stocks. This provides a measure for every position the rule can be adjusted to. An inner top cut scale of 1-17 on the front side, and a hip and valley scale of 1-17 on the tool's reverse side. Tighten the lever to clamp the rule in any desired position. Lift the spring clip to engage and disengage the rule from the standard square home position. The metric roofus Features a 400mm rule, a degree scale on the front side in both angle directions from the stocks. An alphabetic hip and valley scale on the tools reverse side, corresponding to each individual degree marking on the front side. Tighten the lever to clamp the rule in any desired position. Lift the spring clip to engage and disengage the rule from the standard square home position. The traditional Combination square Mark 45 degree lines up to 11 inches or 300mm long. The basic square can be adjusted to any length up to 11 inches or 300mm. Setting the roofus to angle markings Reference edge for all provided markings Reference edge Determine an angle or roof pitch Plumb cut stock is perpendicular to the ground Tighten lever when bubble reads level Angle displayed here The Roofus then provides and displays the angle you have obtained, ready for the task! The Plumb cut stock is perpendicular to the ground Tighten lever when bubble reads level Determine an angle Mark a splay cut up to 15 or roof pitch inches long or 800mm Tighten lever when bubble reads level The plumb cut and seat cut stocks can swap roles like below to obtain angles, or roof pitches greater than 55 degrees. Tighten lever when bubble reads level Basically, the Roofus can obtain any possible angle from one given surface! Marking a standard rafter with the roofus in angle configuration one. 1 2 Heel cut and depth mark Top cut Simply roll the tool to the other stock to achieve the seat cut line! 3 A standard rafter completely marked out ready to cut, with the Roofus set as shown below. Seat cut 4 Marking a rafter with the Roofus in angle configuration two Seat cut Top cut Mark angled checkouts for a gutter, or birds-mouths in raked ceiling rafters in one go! Mark heel cut and depth Seat cut mark, then rotate tool for seat cut. Far deeper checkouts can be achieved the same way as above, in angle configuration two. The Roofus has Seat cut provided here it all covered! Plumb it up Lock it off Top cut Angle displayed here Seat cut Checkout Depth mark Self-standing horizontal level The Roofus is the equivalent of a 400mm level, but also provides a 400mm angle level, to achieve any angle between horizontal and vertical! (any possible angle) Both Bubbles can be easily read from three separate viewing windows, providing convenience in all levelling positions. Vertical level Can be read from places high and low, utilising the full rule length for accuracy. Benchtop level Both vials disposed at 90 degrees to each other are the equivalent of a fish eye level. Fitting cabinets? Marking out posts on footings? The bench top level alleviates slow and tedious jobs, requiring constant checks of multiple level positions. An additional gauge can be made with the unused portion of the rule from the 45 degree stock. Combine this with the tools existing uses and settings to save more time. Marking long splays and wide materials Mark long cladding board splays with ease and accuracy! The Roofus provides the option of either a seat cut or plumb cut at the rulers’ full length. Don’t forget this length can be doubled from the opposite edge of the material, with the tool flipped over. The Roofus can be plumbed up in situ, to obtain any angle between vertical and horizontal, adjusted to any configuration you like! Working out accurate mitre cuts Halve the angle shown on the Roofus, then subtract from 45 to achieve the wall mitre. Halve the angle shown on the Roofus, then subtract 45 to achieve the skirting board mitre. The Roofus was invented by a qualified carpenter, developed by carpenters, on site, doing far more than just carpentry. email: [email protected] website: www.roofus.tools Patent no; 2014277771 mobile; +61 404 247 268 landline +61 8 9535 3732 120 Leighton road Halls Head, Mandurah WA Patent pending; 2015904445 6210 Australia PCT/AU2015/000756 ABN; 75 344 694 986 .

View Full Text

Details

  • File Type
    pdf
  • Upload Time
    -
  • Content Languages
    English
  • Upload User
    Anonymous/Not logged-in
  • File Pages
    16 Page
  • File Size
    -

Download

Channel Download Status
Express Download Enable

Copyright

We respect the copyrights and intellectual property rights of all users. All uploaded documents are either original works of the uploader or authorized works of the rightful owners.

  • Not to be reproduced or distributed without explicit permission.
  • Not used for commercial purposes outside of approved use cases.
  • Not used to infringe on the rights of the original creators.
  • If you believe any content infringes your copyright, please contact us immediately.

Support

For help with questions, suggestions, or problems, please contact us