Suspension/Steering/Brakes/Rear Axle

S12/1 S12/1 SUSPENSION/STEERING/BRAKES/REAR AXLE

“ENERGY” SUSPENSION- BODY MOUNTS ...... S12/1 “IDIDIT”- TILT STEERING COLUMNS ...... S12/1 “IDIDIT”- TILT STEERING COLUMNS-Installation parts ...... S12/2 “IDIDIT” INSTALL’ PARTS- “ENERGY”FRONT SUSPENSION BUSHES...... S12/3 “ENERGY” FRONT SUSPENSION BUSHES- Polyurethane ...... S12/4 “HEIDTS”-FRONT SUSPENSION CROSSMEMBERS ...... S12/5 PARTS REQUIRED TO COMPLETE “HEIDTS”-SUSP’-BRAKES-STEERING... S12/6 STEERING & BRAKES ...... S12/7 BRAKES-REAR SUSPENSION & “ENERGY” suspension bushes ...... S12/8 “COMPETITION ENGINEERING” REAR SUSPENSION ...... S12/9 “HEIDTS”-REAR SUSPENSION [4-LINK] -AIR RIDE...... S12/10 AIR-RIDE TANK & PUMP SYSTEM- REAR AXLE & PROPSHAFT PARTS ...... S12/11 SHOCKABSORBERS -”RIDETECH” HD AMERICAN MADE ...... S12/12

Energy Suspension Polyurethane performance components, are made in the USA. Energy use a material called “Hyper-Flex”, which is the result of 20+ years of experience. Careful selection of material firmness [durometer] is used for each specific application on the vehi BODY MOUNTS cles suspension & frame. Hyper-Flex components do not rot or deteriorate from exposure to oils & under-car chemicals or atmospheric conditions, like smog & ozone. Handling & steering response is vastly improved over standard, soft bushes. Ride could be stiffer.

Chevrolet full Size Chevrolet Camaro Polyurethane body mount set-Black Polyurethane body [subframe] mount set-Black

BY3-4106G 1955-57 Not 2dr hardtop ...... £43.36sp BY3-4138G 1965-70 2dr hardtop ...... £40.48sp BY3-4142G 1967-2002 all models Black ...... £94.88

Chevrolet Corvette Chevrolet Chevelle, Malibu, Monte-Carlo, Laguna, El-Camino

Polyurethane body mount set-Black Polyurethane body mount set-Black BY3-4128G 1964 Not convertible ...... £56.68sp BY3-4102G 1963-67 Hardtop only ...... £30.23sp BY3-4111G 1965-67 Not convertible ...... £60.67sp [part above is pictured] BY3-4115G 1968-72 Not convertible ...... £42.49sp BY3-4134G 1970-72 Monte-Carlo not convert ...... £45.80sp

Pontiac Firebird & Trans Am

Polyurethane body [subframe] mount set-Black

BY3-4142G 1967-75 check below ...... £94.88 BY3-4144G 1976-81 ...... £97.88

The IDIDIT steering column is world renowned, and since 1986 has been fitted to many thousands of Hot-Rods, all over the world. IDIDIT is a family business, based in the state of Michigan, and their steering columns are made in the USA, to very high standards. Vari ous finishes are available, although we only carry in stock- chrome & paintable-steel. Other finishes, like- black powder coated, brushed & polished aluminium, are available to order. STEERING COLUMNS These columns are available in plain, 8 position tilt and with or without column shift. Measuring your car, to see which column would be best, is critical. Please ask for measur ing instructions and we will gladly send them to you . More time spent doing this, will ensure a perfect fit later on. Most columns feature a flashing indicator control, a 4-way hazaard light control & horn. Other options including cruise control are available.

Tilt Steering Column Paintable Steel-Universal Tilt Steering Column Chrome-Universal Does NOT have column shift Does NOT have column shift Made by iditit- Made by iditit-

BYAJW255 30” length, 2” tube OD ...... £435.88 BYAJW260 30” length, 2” tube OD ...... £584.15 BYAJW245 32” length, 2” tube OD ...... £446.81 BYAJW250 32” length, 2” tube OD ...... £636.82 Tilt Steering Column PAINTABLE Steel-Universal Tilt Steering Column CHROME-Universal HAS column shift HAS column shift Made by iditit- Made by iditit-

BYAJW605 30” length, 2.25” tube OD ..... £652.84 BYAJW610 30” length, 2.25” tube OD ..... £859.68 BYAJW585 33” length, 2.25” tube OD ..... £647.57 BYAJW615 33” length, 2.25” tube OD ..... £960.10

Iss84 S12/2 S12/2 - SUSPENSION/STEERING/BRAKES/REAR AXLE - Steering

TILT STEERING COLUMN Paintable Steel-1955-56 Chevy TILT STEERING COLUMN CHROME- Ford Mustang This column HAS column shift If you retain the original manual steering box, you will need to chop off the inner shaft and re shape to take a coupler. An installation kit may be required. Has These columns are for floor shift only. Designed for your classic provision to use original dash indicator. Only works with 3 & 4 Mustang. Save and use your original under dash mount. A new speed, not Powerglide. floor mount comes with the column. Complete with a Ford turn signal switch, and a Ford type wiring plug. Designed to accept BYAJW185 1955-56 Chevy ...... £408.58sp your original Mustang steering wheel, and place it in the original position. You could use an alternative steering wheel with an adaptor. The lower shaft is 3/4” x 36. For the 1965-66 you will need a TILT STEERING COLUMN Paintable Steel -1967-69 Camaro coupler BYAJW195. You will also need to cut off your old shaft, which goes into the steering box, & modify it to 3/4” DD. Does NOT have column shift. A 1969 Camaro steering wheel, bolts directly to the IDIDIT column. It is recommended you fit a new “rag joint” connection. BYAJW860 1965-66 Mustang ...... £718.33 BYAJW870 1968 Mustang- collapsible ..... £471.32sp BYAJW050 ‘69 Camaro w/ignition ...... £371.35sp BYAJW875 1969 Mustang- collapsible ..... £481.08sp

STEERING COLUMN ACCESSORIES & INSTALLATION PARTS

BUDGET FLOOR MOUNT WITH TRIM RING This lower bracket comes with a polished aluminium trim ring & hardware. To complete the installation, a boot is also available.

BYAJW105 Floor mount trim kt 2” tube ..... £63.00 BYAJW110 Black boot for above kit ...... £28.96

PIVOTING DROP BRACKETS-Polished Aluminium FLOOR MOUNTS FOR COLUMN Often required to hold the steering column in place, at the In some cases, the original bottom column mount, will not work right angle, where the original part will not work. with your new column. BYAJW070 2” tube, 2-1/2” drop ...... £110.64 BYAJW170 2” tube budget mount ...... £35.76 BYAJW075 2” tube, 3-1/2” drop ...... £116.39 BYAJW115 2-1/4” tube budget mount ..... £35.76 BYAJW190 2” tube budget Tr-Chevy ..... £10.62sp BYAJW080 2-1/4” tube, 2-1/2” drop ...... £108.98 BYAJW085 2-1/4” tube, 3-1/2” drop ...... £89.88 BYAJW175 2” swivel ball floor mount £156.65 BYAJW500 2-1/4” swivel ball floor mount £140.33 BYAJW515 2-1/4” tube, 5” drop 32 Ford .... £50.02sp Above numbers [BYAJW175/500] are for a chrome stg column BYAJW830 Upper mount bracket ...... £13.75 Use this metal bracket on a 47-54 Chevy P/U BYAJW505 2-1/4” swivel ball floor mount £95.47sp

STEERING COUPLER FEMALE PLUG-IDIDIT Steering Column-3-7/8”

1965-early 67. On these vehicles, the steering staft comes out of the steering This 3-7/8” plug mates up to the plug on some IDIDIT steering columns. box and up into the column [one piece]. To fit a different column, this shaft Please check this will fit your column before purchase. This plug enables will need to be cut, & then modified to take the coupler. you to wire up your column using a proper plug.

BYAJW195 Coupler 3/4 x 36 //3/4 DD ...... £70.88 BYAJW140 Female plug 3-7/8” ...... £19.52 S12/3 S12/3 - SUSPENSION/STEERING/BRAKES/REAR AXLE - Steering/Front Suspension INDICATOR FOR TRANSMISSION CRUISE CONTROL KIT Enables you to see which gear you are in. Mounts on top of column. Includes the parts needed to fit cruise control on a non computer- ised engines. Servo & control unit are small enough to fit under BYAJW120 Acrylic indicator +pointer 3spd ...... £21.42sp any dash. Includes pulse generator & control handle. Add this BYAJW125 Acrylic indicator +pointer 4spd ...... £16.26sp worthy item to your column. BYAJW130 Also includes chrome housing 3spd .... £85.76 BYAJW160 Cruise control kit ...... £221.98sp BYAJW135 Also includes chrome housing 4spd .... £83.66 BYAJW165 Cover-cruise handle-alum pol .. £20.03sp

CABLE SHIFT FOR COLUMN CHANGE This kit enables you to connect up your new column to your automatic trans. Consists of- cable, transmission bracket and cable bracket for column.

BYAJW090 GM Trans 69 on, IDID 2” £107.78sp BYAJW095 GM Trans 69 on, IDID 2.25” £151.30

BYAJW625 C4/C6 Link clamp assy 2.25” £59.92

BYAJW630 C4 Trans bracket/cable kit £63.91sp BYAJW640 C6 Trans bracket/cable kit £61.72sp

COUPLING PARTS FOR STEERING RACK/BOX STEERING WHEEL ADAPTERS In most cases, a steering wheel adapter will be required to enable you to attach your steering wheel to your IDIDIT column. There are many types of coupling to join your column to your steering rack/box. Here are some of them-others available to order- BYAJW040 3 bolt chrome ...... £137.21 BYAJW030 9 bolt polished- short ...... £163.45 BYAJW035 3 bolt polished ...... £79.28 BYAJW060 9 bolt polished inc IDIDIT button ...... £96.34 BYAJW988 Shaft support 3/4” £42.23 BYAJW055 9 bolt chrome inc IDIDIT button ...... £153.24 The above support is required where 3 u/j’s are being used [part above is pictured] BY31120 9 bolt Billet Spec’ polished alum’ ...... £64.44 BYAJW750 UJ steel 3/4” DD to 26 x 9/16” £136.96 HORN BUTTONS- B/SPECIALTIES Above joint is for Heidts manual stg rack BY32125 Large [covers screws] plain ...... £55.94 BY32325 Large “bowtie” ...... £45.80sp BYAJW495 UJ steel 36 x 3/4” to 3/4” DD £138.14 BY32625 Large “Billet Specialties” ...... £63.20 Above joint is for Heidts power stg racks with 36 x 3/4” pinion BYRP2510Horn wire lead ...... £11.98 STEERING WHEELS BILLET SPECIALTIES BYAJW645 UJ steel 1”DD to 3/4”DD £142.52 These steering wheels use a 9 bolt adaptor. They have milled finger notches BYAJW595 U-joint steel 3/4DD to 3/4DD £137.66 for an ultra comfortable grip. Many types available. BY30976 Anthem- 14” ...... £176.95 BYAJW600 UJ steel Mustang “V” to 3/4DD £96.26 BY30725 Classic 14” ...... £192.58sp Above joint is for power stg racks with Mustang “V” pinion BY30925 Banjo 14” ...... £312.00 BY30973 Speedway 14” ...... £202.57 BYAJW535 u/j pol S/S Must”V”x3/4”DD £138.20sp BY30137 Split Spoke- 14” ...... £274.08 Shown at right The above joint has a built in vibration reducer, designed to BY29003 Gray leather 14” half wrap ...... £55.97 stop pulses from the power steering pump reaching the column. BY29005 Red leather 14” half wrap ...... £58.86 BYAJW195 Coupler- 3/4”-36 x 3/4” DD £76.19 BY29008 Black leather 14” half wrap ...... £55.96 BYAJW200 Coupler- 1 DD x 3/4” DD £73.31 BY29002 Tan leather 14” half wrap ...... £30.07sp BYAJW675 Steel shaft 3/4” DD - 16” £30.62 BY29006 Burgundy leathr 14” half wrap ..... £30.67sp Leather half wrap is required for all above wheels BYAJW680 Steel shaft 3/4” DD - 32” £58.32

FRONT SUSPENSION

CHEVROLET/PONTIAC Full Size CHEVROLET Camaro/PONTIAC Firebird & Trans am BY3-3108G 1955-64 Chevrolet ...... £92.22 Polyurethane front end control arm bushing set BY3-3150G 1965-70 Chevrolet ...... £35.18sp Polyurethane front end control arm bushing set Lowers- reuse metal parts BY3-3103G 1971-73 Chevrolet + Bonneville ...... £51.11sp BY3-3101G 1967-69 ...... £85.79 Only models with 1-5/8” OD front lower bushes. BY3-3102G 1970-72 ...... £62.74 BY3-3104G 1973-74 1-3/8” OD lowers ...... £70.58 BY3-3103G 1973-74 1-5/8” OD lowers ...... £51.11sp Above part also fits 1973 Firebird BY3-3105G 1975-79 ...... £85.78 Above part also fits 1974-79 Firebird BY3-3106G 1980-81 ...... £89.96 BY3-3157G 1982-92 Lowers only ...... £48.19 BY3-3164G 1993-02 [Lowers re-use metal parts] .. £87.35 S12/4 S12/4 - SUSPENSION/STEERING/BRAKES/REAR AXLE - Front Suspension

CHEVROLET CORVETTE CHEVROLET & PONTIAC

Polyurethane front end control arm bushing set These bushes will give added performance without creating any adverse changes to the original ride. Polyurethane front end control arm bushing set

BY3-3108G 1963-82 ...... £92.22 BY3-3101G 1966-74- Bushes are round ...... £85.78 BY3-3142G 1984-96 ...... £60.31sp Chevelle, Malibu, Monte-Carlo, Laguna, El-Camino, LeMans, GTO, Tem- pest. On 1966 Chevrolet models, there are two size rear lower bushes, these Chrysler- RWD are 1.65” OD. Nova & Chevy 2- 1968-74. BY3-3160G 1962-67 ...... £33.73sp Polyurethane front end control arm bushing set Above number fits- Nova, Chevy 2- 1962-67.

BY5-3132G 1962-76 A body uppers only ...... £47.23 This number also fits “B-Body” 1965-72 uppers only & “E-Body” 70-74

Chrysler notes- FORD MOTOR COMPANY Polyurethane front end control arm bushing set. Must re-use existing outer metal shells. “A” body- Dart, Demon, Duster, Valiant (Barracuda to 69) BY4-3101G 1960-66 ...... £12.42 “B” body- Charger, Coronet, Satellite, GTX, Roadrunner, Superbee Falcon, Ranchero, Mercury Comet 1961-65, Mustang-lowers only “E” body- (Barracuda 70 and up) & Challenger BY4-3131G 1962-65 Fairlane ...... £13.43sp BY4-3102G 1967-71 1-7/16” OD lower ...... £15.40 Fairlane, Grand Torino, Torino, Ranchero, Mercury Comet 1966-77, Mus- tang 67-73 1-7/16” OD lower BY4-3106G 1967-71 1-9/16” OD lower ...... £14.88 Fairlane, Grand Torino, Torino, Ranchero, Mercury Comet 1961-65, Mus- tang 1967-73 1-9/16” OD lower BY4-3130G 1974-78 Mustang ...... £62.74 BY4-3132G 1979-82 Mustang excl HD susp’ ...... £36.71 Above also fits Mustang 1983-93 BY4-3108G 1979-82 Mustang with HD susp’ ...... £15.23sp BY4-3144G 1994-04 Mustang ...... £36.88sp

FRONT STRUT ROD BUSHES

FORD MOTOR COMPANY Chevrolet Polyurethane front strut rod bushes Polyurethane strut rod bushes BY3-7109G 1965-70 ...... £14.44sp BY4-7111G 1960-66 ...... £25.15 Above number fits- Belair, Biscayne, Caprice, Impala, Station Wagon Above number fits- Falcon, Ranchero, Fairlane 62-65, Mustang 64-66, BY3-7105G 1962-67 ...... £10.38sp Mercury Comet 1961-65 Above number fits- Nova & Chevy 2 BY4-7112G 1967-71 ...... £29.64 Above number fits- Fairlane, Grand Torino, Torino, Ranchero, Mustang 1967-73, Mercury Comet 1966-77, Cougar 1967-73 BY4-7117G 1972-79 ...... £18.56sp Chrysler- RWD Above number fits- Fairlane, Grand Torino, Torino, Ranchero, Galaxie 1965- Polyurethane front strut rod bush set 78, Thunderbird 1972-79, Cougar 1974-79 BY4-7113G 1974-78 ...... £15.43sp BY5-7105G 1962-65 ...... £6.60sp Above number fits- Mustang 1974-78 Above number fits- “A” body 62-65 .

FRONT END LINKS-anti-roll bar

Lengths- relate to straight shaft between bush platform washers

FRONT ANTI-ROLL BAR LINKS FRONT ANTIROLL BAR LINKS Polyurethane bushed front end links for anti-roll bar BY9-8117G 2-5/8” ...... £25.99 Polyurethane bushed front end links for anti-roll bar Above number fits- 1955-57 & 1971-90- Belair, Biscayne, Caprice, El Camino BY9-8120G 1-5/8” ...... £22.54 (thru 63), Impala, Station Wagon; Camaro/Firebird & Trans Am 1967-92; Above number fits- 1965-70- Belair, Biscayne, Caprice, El Camino (thru +73-77 Chevelle, Monte Carlo, Malibu & El Camino 64 up; Monza & Vega 63), Impala, Station Wagon, Corvette 63-82; Chrysler “E” body 70-74; 1971-80; Nova & Chevy 2- 1962-79; Mustang 67-73; Cougar 67-73; Pontiac Chrysler “B” body 70-72; Chrysler “A” body 1973-76; Fairlane, Grand Torino, LeMans, GTO, Tempest 73-77; Bonneville, Catalina (Grand Prix to 81 only), Torino, Ranchero 67-71; Mustang 64-66; Comet 66-77; Safari Wagon 71-81; BY9-8121G 4-1/2” ...... £11.42sp BY9-8118G 2-7/8” ...... £21.53 Above number fits- Mustang 79-93; Above number fits- Camaro/Firebird & Trans Am 1993-02; +1964-72- Chevelle, Monte Carlo, Malibu & El Camino 64 up; Chrysler “B” body 65- BY9-8124G 3-9/16” ...... £11.26sp 69; Chrysler “A” body 65-72; Fairlane, Grand Torino, Torino, (Ranchero Above number fits- Mustang 94-04; after 15-3-72) 72-79; Galaxie 72-78; Thunderbird 72-79; Cougar 74-79; BY3-8102G 1984-87; ...... £6.73sp Pontiac Le Mans, GTO, Tempest 64-72; Above number fits Corvette BY9-8119G 1958-64; 3-3/8” ...... £21.36 BY3-8103G 1988-96; ...... £6.73sp Above number fits- Belair, Biscayne, Caprice, El Camino (thru 63), Impala, Above number fits Corvette Station Wagon. S12/5 S12/5 - SUSPENSION/STEERING/BRAKES/REAR AXLE - Front Suspension

ANTI-ROLL BAR BUSH SETS-with Brackets Anti-Roll Bar Bushes

Polyurethane Anti-Roll Bar Bush sets. Brackets are 4-1/2” long, by 1-3/8” wide, 1-3/4” high, 3/4” from centreline of hole for bar, to mounting face of bracket. Mounting bolts centre to centre can be between 3-5/8” and 2- 9/16” [holes are slots].

BY9-5106G 3/4”- 19mm ...... £22.38 set CHEVROLET Camaro-Nova & Chevy 2 BY9-5108G 7/8”- 22mm ...... £22.55 set BY9-5109G 15/16”- 24mm ...... set £12.26sp Polyurethane front anti-roll bar bushes BY9-5110G 1”- 25mm ...... £22.13 set BY9-5112G 1-1/8” - 28.5mm ...... £22.38 set BY9-5113G 1-1/4” - 31.5mm ...... £20.63 set BY3-5203G 13/16” Bar ...... set £20.30 Above numbers fit- Camaro 67-69; Nova & Chevy 2 68-74 HEIDTS FRONT SUSPENSION

Heidts were one of the first companies to make alternative crossmember based suspension assemblies, based on the 1974-78 Mustang II front suspension. Up until a few years ago, the Mustang II could be readily found in scrapyards, and it was a simple matter to “remove” the front suspension, and modify it to suit ones Hotrod. Nowadays, these cars are getting a bit thin on the ground. This is where Heidts comes in [23 years in business], manufacturing cross members to fit many classic cars & trucks. If you have the suspension parts from a Mustang II, then these will fit the crossmember. Otherwise, you can buy all new components, with many different options. The Heidts front suspension design, follows faithfully, the design used by Ford Motor Company. This is because it is technically a very good design. Ford got it right first time with this design, eliminating bumpsteer, and including built-in anti-dive into the design. Some of the other Mustang II based designs do not have these features. Hotrods & Custom/Street cars built these days, need to be safe, as more & more families have become involved, giving us a much greater responsibility. The car needs to handle and brake in safety, from speed. It is no good anymore having a car that will do 200mph in a straight line, but has poor brakes & suspension. Tailgating the family in a 2019 Vauxhall Insignia on the M1 at 85mph, in your 1500bhp twin turbo ‘34 Ford coupe, is not a good idea, unless you have brakes the equal of his. The Heidts front suspension cross-member is made in the USA, not China, and it is beautifully made, a work of art. I visited the Heidts factory, just north of Chicago, and was very impressed with the high quality of their work. I look forward to fitting one of these kits to my own car in the future.

FRONT SUSPENSION CROSSMEMBER Boxing plates included. Narrowed suspension arms recommended. Weld on engine mount brackets are avail- Ford V8 BYAJW335 & Chevy BYAJW450

BYPX-102-E Ford ‘35-40 Car & ‘35-41 P/up ...... £301.88sp FRONT SUSPENSION CROSSMEMBER FRONT SUSPENSION CROSSMEMBER

Steering rack extensions required Steering rack extensions required Weld on engine mount brackets are available-Ford V8 BYAJW335 Weld on engine mount brackets are available-Ford V8 BYAJW335 and Chevy V8 BYAJW450 and Chevy V8 BYAJW450

BYPX-104-E Ford 1948-52 F-1 Pickup ...... £472.73 BYPX-105-E-K Ford 1953-64 F-100 Pickup ...... £488.22

FRONT SUSPENSION CROSSMEMBER

“C” notched plates included. Steering rack extensions required. Weld on engine mount brackets are available-Ford V8 BYAJW335 and Chevy V8 BYAJW450

BYCX-308-E-K Chevy 1955-59 Pickup ...... £484.25

FRONT SUSPENSION CROSSMEMBER Mustang 1964-70+67-70 Cougar, 351W, 351C, 460BBF, FE engines, w/rear sump Includes boxing plates that weld in place. 2” dropped spindles recommended for std ride height. BYPM-320-E-K Mustang see above ...... £506.93

FRONT SUSPENSION CROSSMEMBER FRONT SUSPENSION CROSSMEMBER “C” notched plates included Mustang 1964-70+67-70 Cougar, 289, 302, Coyote, Weld on engine mount brackets are available-Ford V8 BYAJW335 Mod engines w/rear sump and Chevy V8 BYAJW450 NOTE: Some 54’s were sold in ‘55 be sure of your model! Includes boxing plates that weld in place. 2” dropped spindles recommended for std ride height. BYCX-307-E-K Chevy 1947-54 Pickup ...... £496.37 BYPX-320-E-K Mustang see above ...... £595.87 S12/6 S12/6 - SUSPENSION/STEERING/BRAKES/REAR AXLE - Front Suspension

WHAT ELSE DO I NEED?

SUSPENSION ARM KIT, BRAKE SYSTEM KIT, STEERING RACK & MOUNT KIT, SPRINGS, SHOCKS and RUBBER SEATS, SPINDLE/FRONT UPRIGHT KIT, BRAKE HOSE KIT, STEERING COLUMN CONNECTION PARTS [see S12/3], ANTI-ROLL BAR [option] -most kits are pairs & include required hardware, everything is unpainted-

TUBULAR SUSPENSION ARM KITS [unpainted] VENTED- DISC BRAKE KITS [unpainted -]choose one! choose arms tubes & gussets! BYAJW655 11” brake kit Chevy bolt circle ...... £584.69 BYAJW545 Std arm kit ...... £778.76 BYAJW685 11” brake kit Ford bolt circle ...... £542.06 BYAJW560 Coil-over shock arm kit ...... £823.10 Chevy bolt cicle = 5 on 4-3/4”, Ford bolt circle = 5 on 4-1/2” Coil over shocks make it easier to adjust the vehicle height [front] BYAJW690 11” Chev-Willwood blk callipers ...... £579.06sp BYAJW580 Narrowed std arm kit [some Fords] .. £882.85 BYAJW695 11” Ford- Willwood blk callipers ...... £798.07 BYAJW635 Narrowed coil-over shock arm kit ..... £909.35 Callipers are lighter [aluminium]. They are the 4 piston version BYAJW550 Air-bag arm kit ...... £963.91 The above kit requires the Air-Bag installation pack BYAJW810 SPRINGS & SHOCKABSORBERS BYAJW820 Spacer tubes for crossmember-2req .... £19.49ea choose shocks, springs & rubber seats! BYAJW670 Gussets for crossmember-2req ...... £3.78ea The above two line items need to be welded into the c/member [2 ofeach] BYAJW020 Standard shockabsorber ...... £105.02 pr BYAJW275 Replacement bushes upper arms ...... £14.70ea BYAJW850 Billet aluminium coil over shock ...... £644.58pr BYAJW280 Replacement bushes lower arms ...... £18.90ea The above shock has 10 position adjustable [rebound] damping BYAJW285 Replacement ball joints ...... £24.61ea BYAJW305 Rubber seat for shock [required] ...... £30.40pr BYAJW215 Black 300lb spring for std shock ...... £211.28pr STEERING RACK KITS- choose rack & mounts! BYAJW295 Black 350lb spring for std shock ...... £220.27pr Black springs fit between upper & lower arms with std shock through centre. No ride height adjustment, apart from correct pressure spring and 3/4” spacers BYAJW710 Manual rack LHD- 26 x 9/16” ...... £252.16 available under part number BYAJW825 to raise ride height of vehicle. Mounts included. Use universal joint BYAJW750 with above rack BYAJW825 Spring spacers-3/4” ...... £40.42pr If your vehicle is riding a bit low in the front, these spacers will lift the BYAJW106 Power LHD-Mustang II 36x3/4” ...... £679.96 Heidts springs up around 3/4”. Uses BYAJW495 universal. Complete with mounting kit. NEW! BYAJW1000 Silver 375lb spring-coil overs ...... £134.64pr BY8026070 Fittings for rack to attach hoses ...... £38.35 BYAJW805 Silver 500lb spring-coil overs ...... £184.92pr BYAJW1015 Poly bushes rack mounting ...... £40.62pr BYAJW485 Silver 600lb spring-coil overs ...... £184.92pr Above kits must be used for POWER steering racks. BYAJW1025 Track rod ends for power rack ...... £34.87 BYAJW290 Silver 700lb spring-coil overs ...... £178.16pr These springs mount on an adjustable platform on the shockabsorber. This gives ride height adjustment. A spanner to adjust the spring height is available under part number BY62030. BYAJW887 Flat bearing for coil overs ...... £85.82 pr The above bearing makes adjusting the ride height much easier.

SPINDLE [FRONT UPRIGHT] KITS HEIDTS FRONT ANTI ROLL BARS choose one! option!

BYAJW700 Std height “Mustang II” ...... £278.58 BYAJW705 2” drop “Mustang II” forged ...... £334.39 On a Mustang, the 2” drop spindles are needed for “std” ride height These anti-roll bar kits come complete with all parts required to fit. Assists in keeping your car/truck sitting flat through the corners. If marked with * then BRAKE HOSE KITS -choose one! only works with Heidts Must II, front end kit. BYAJW590 Std Heidts brake kits ...... £78.36 Use with BYAJW655/685 BYAJW435 1955-57 Chevy 1” diam+urethane .... £170.70sp BYAJW740 Heidts brake kits w/Willwood 14” ...... £54.79 Use with BYAJW690/695 BYAJW660* 1948-54 Ford P/up +53-56 F100 ...... £237.16 BYAJW745 For Willwood callipers 16” hose ...... £48.10 BYAJW540 Weld on tab kit for brake hose ...... £30.76 BYAJW525 * 1940-46 Chevy Pickup ...... £197.84

AIR BAG INSTALLATION PACK BYAJW665* 1947-54 Chevy Pickup ...... £294.77 Picture shows more parts than in kit BYAJW1060 1955-59 Chevy Pickup * ...... £213.67

BYAJW310* 1964-70 Must’+1967-70 Cougar ...... £234.01sp BYAJW810 Heidts Air-Bag kit for BYAJW550 .. £654.85 Use with BYAJW550 to finish air-bag type front end BYAJW960 1964-70 Must’ V2 crossmember * .... £257.32

See also next page- - SUSPENSION/STEERING/BRAKES/REAR AXLE - S12/7 Steering & Brakes S12/7

AirRide Air-Spring Conversion Kit This kit gives you the “spacers” or “towers” and the shock brackets to enable the installation of airbags in a Heidts Mustang II front end, if you have the correct lower arms. You will also need shockabsorbers & the Airbags. BYAJW465 AirRide parts [Must II front end] ...... £82.99sp

1” Dropped Coil Springs Chevy 55-6-7 To give your shoebox an even lower look, add these Heidt 1” dropped coil springs. Combined with the 2” dropped spindles, they will put your cruiser a full 3” in the weeds safely & easily.

BYAJW430 1” lower spring Chevy 55-6-7 ...... £80.33

MUSTANG CHASSIS STIFFENER 1964-70 MUSTANG 1964-70 Inner Wing Panels

This is another item that gives the unibody design added stiffness Use when fitting the Heidts front subframe kit. Remove the old for performance use. Use with Heidts subframe connectors. panels, and replace with these.

BYAJW315 Inner wing panel 64-66 Mustang ...... £42.29 BYAJW345 Chassis stiffener 64-70 ...... £362.23 BYAJW320 Inner wing panel 67-70 Mustang ...... £95.16

STEERING

STEERING RACK EXTENSION KITS 4” MUSTANG POWER RACK CONVERSION KIT Mustangs can have a bit of “slack” in the “feel” of the steering. They can also leak fluid everywhere. Complete with pump, hoses These extensions are required on SOME Heidt front crossmember kits. and connection parts for your steering column. You can tell an Look at crossmember information to find out. early ‘67, it does not have a “rag-joint” connection to the stg box. BYAJW990 Mustang 65- 66 Small Blk ...... £1675.15 BYAJW4702 4” extensions manual Heidt rack ...... £66.41 BYAJW1020 Mustang early 67 [no rag joint] ...... £1581.58 BYAJW475 4” extensions power Heidt rack ...... £90.55 BYAJW995 Mustang late 67-70 [has a rag joint] ... £1581.58 POWER STEERING PUMPS HEIDTS Adjustable Power Steering Valve We stock two types of pump. The GM pump with a keyed shaft & reservoir attached and the Maval pump with plastic tank. Racks are generally low volume, steering boxes mainly high volume. Tune your power steering, with the Heidt patented adjustable power steering valve. If you are using a high-flow pump with a steering rack, you can adjust BYAJW965 GM lo-flo black- keyed ...... £184.93 the “feel” using this valve. BYAJW925 GM lo-flo chrome-keyed ...... £270.62 BYP304 GM hi-flo chrome- keyed ...... £228.55 BYAJW455 Adjustable power steering valve ...... £134.47 BYAJW845 Pump & tank lo-flo ...... £160.55sp BY8020630 Pulley for BYAJW845 ...... £53.26sp POWER STEERING PUMP HOSE KITS BYAJW970 Pump kit SBC lwp lo-flo ...... £356.33 BYAJW1055 Pump kit SBF lo-flo ...... £492.16 BYAJW1040 Power steering pipe kit ...... £174.98 The above 2 pump kits are lo-flo & comes with brackets Use the kit BYAJW1040 with the pumps- BYAJW965, BYAJW925 BYAJW975 Steel brackets SBC lwp ...... £45.19sp BYAJW980 Steel brack’ Pont 400 ...... £45.19sp BYAJW1010 Power steering pipe kit ...... £112.76 Steel brackets are for BYAJW845 pump only Use the kit BYAJW1010 with the pumps- BYAJW845, BYAJW970

BRAKES

MUSTANG FRONT 11” DISC BRAKE KITS 1964-69 REPLACEMENT DISC PADS FOR BYAJW1045

For Mustang V8- 5 stud OEM wheel cars that origi- Note: There is not just one type: nally had drum brakes from Ford. Callipers are single piston. A disc brake servo will be required to create enough pressure. [Disc brakes require more line pressure than drum brakes to function efficiently]. BYD159 Disc pad set for BYAJW1045 ...... £29.28

FRONT 11” DISC BRAKE KIT ‘55-57 CHEVY Picture shows an AJW1045 kit, for one wheel. Kits contains all the parts needed for two wheels.[1 car] Use this kit where the vehicle has Heidts 2” dropped front uprights or spindles.

BYAJW1045 V8 64’-69 w/oem wheels ..... £690.70 Will also fit 1970 if appropriate wheel brgs used. BYAJW420 Disc brake kit for 2” drop ...... £324.23 S12/8 S12/8 - SUSPENSION/STEERING/BRAKES- Brakes/Rear Suspension Original Type

ELECTRIC VACUUM PUMP KIT MUSTANG 1964-66 DUAL M/CYLINDER & SERVO

If you have a long duration cam in your engine & the idle vacuum is poor, the This is a complete dual master cylinder together with an 8” dual diaphragm other option is to use an electric vacuum pump so that your brake servo will brake servo or booster. Will work with OEM drum/drum *** or aftermarket function correctly. Otherwise, your brakes [disc or otherwise] will be poor. disc/drum. Will work with automatic or manual transmission. *** For use with drum/drum the proportioning valve must be removed

BY5500 Electric vacuum pump ...... £394.64 BYAJW1030 1964-66 m/cyl & servo- ...... £422.10

MUSTANG 1967-70 MASTER CYLINDER/SERVO MUSTANG 1967-69 8” SERVO only

This is a complete dual master cylinder together with a 7.5” dual diaphragm This is an 8” dual diaphragm brake servo or booster. Will work with OEM brake servo or booster. Will work with OEM drum/drum or aftermarket disc/ drum/drum or OEM disc/drum. Will work with automatic or manual trans- drum. Will work on a car that left the factory with either a manual or auto- mission. Must have originally had power brakes from Ford.. matic transmission, & non power brakes. OK with V8 or 6cyl.

BYAJW920 1967-70 m/cyl & servo ...... £425.56 BYAJW950 1967-69 servo replaces OE .... £261.26

MUSTANG 1970 8” SERVO only MUSTANG 1971-73 8” SERVO only This is an 8” dual diaphragm brake servo or booster. Will work with OEM This is an 8” dual diaphragm brake servo or booster. Will work with OEM drum/drum or OEM disc/drum. Will work with automatic or manual trans- drum/drum or OEM disc/drum. Will work with automatic or manual transmission. Must have originally had power brakes from Ford.. mission. Must have originally had power brakes from Ford..

BYAJW930 1970 servo replaces OE ...... £261.26 BYAJW1005 1971-73 servo replaces OE .. £261.26

CHEVY 1955-6-7 DUAL M/CYL & SERVO 1947-54 CHEVY PICKUP-CHASSIS MOUNT This is a complete dual master cylinder together with a brake -dual m/cyl & servo- servo or booster, for disc/drum setups. These kits come complete with a piped up proportioning valve, to reduce pressure to the Dual master cylinder & 8” Bendix style servo, rear brakes. chassis mounted. Set up for disc /drum. Includes mounting brackets. Proportioning valve included.

BYAJW415 Dual m/cyl & servo ‘55-57 ..... £411.07 BYAJW945 Dual m/cyl & servo ...... £622.52

1953-56 FORD PICKUP-CHASSIS MOUNT ADJUSTABLE BRAKE PROPORTIONING VALVE -dual m/cyl & servo- Dual master cylinder & 8” servo, chassis mounted. An adjustable brake proportioning valve is used to balance front Includes mounting bracket & remote reservoir. and rear brake pressures, especially in disc/drum combinations. Set up for disc /drum. Proportioning valve incl.

BYAJW940 Dual m/cyl & servo ...... £513.83 BYAJW445 Adj’ brake proportioning valve ...... £68.35

FORD PROPORTIONING VALVE

This is a 70’s style valve that could attach to the inner wing. It is set up for a disc/drum system.

BYAJW955 Ford proportioning valve ...... £58.60

REAR SUSPENSION

CHRYSLER “A” & “B” Body Leaf Spring Bushes Chrysler notes- Polyurethane rear leaf spring bushing set

“A” body- Dart, Demon, Duster, Valiant (Barracuda to 69) “B” body- Charger, Coronet, Satellite, GTX, Roadrunner, Superbee BY5-2104G 1965-72 “B” w/1/2” eye 426+440 ...... £33.04sp “E” body- (Barracuda 70 and up) & Challenger

CHEVROLET & PONTIAC SALOON MUSTANG/CAMARO HD SHACKLE KIT

Polyurethane rear control arm bushes Polyurethane bushed HD rear shackle bushes & hardware kit

BY3-3133G 1964 uppers reuse outer metal shells £51.88sp BY4-2136G 1964-73 Mustang ...... £101.53 1964Chevelle, Monte Carlo,Malibu, Lemans, GTO & El Camino 1964on BY3-2135G 1967-81 Camaro ...... £88.14 - SUSPENSION/STEERING/BRAKES/REAR AXLE - S12/9 -Rear Suspension- S12/9

CHEVY CAMARO/PONTIAC F/BIRD REAR SUSPENSION CHEVROLET CORVETTE REAR SUSPENSION Polyurethane rear leaf spring bushing set Polyurethane rear leaf spring bushing set BY3-2101G 1967-69 Camaro-F/bird Mono-leaf ..... £71.30 BY3-2121G 1954-62 rear leaf spring bushes ...... £13.44sp BY3-2103G 1970-81 Camaro-Firebird ...... £82.92 Polyurethane rear control arm bush set BY3-3191G 1963-82 rear control arm bushes ...... £36.47 Polyurethane leaf spring pads BY3-6112G 67-69+62-79 Nova/ChevyII multi ...... £27.25 Polyurethane rear leaf spring spring cushions Above item also fits 62-79 Nova & Chevy II+Firebird 68-69 Multi BY3-2104G 1963-82 spring cushions ...... £17.63 BY3-6111G 1970-81 multi leaf ...... £36.05 BY3-2123G 1984-96 spring cushions ...... £8.50sp Polyurethane rear control arm bushes BY3-3136G 1982-02 Rear control arm bushes ...... £57.52 Polyurethane Torque Arm mount bushes BY3-1111G 1984-92 & 1993-02 Torque arm bush . £23.93 Polyurethane diff pinion mount & carrier bush set “Lips” facing away from driveshaft-see Energy catalogue drawing BY3-1101G 1963-82 pinion mount set ...... £12.92 Polyurethane rear control arm bushes BY3-1104G 1980-82 diff carrier bush set ...... £32.98 BY3-7106G 1982-01[02-Pont]panhard bar bushes . £21.67 BY3-1103G 1984-96 diff carrier bush set ...... £17.00sp

FORD FAIRLANE & MUSTANG REAR SUSPENSION CHEVROLET LEAF SPRING BUSHES

Polyurethane rear leaf spring bushing set Polyurethane rear leaf spring bushing set BY3-2118G 1955 Chevrolet ...... £41.45 BY4-2141G 1962-65 Fairlane ...... £34.69sp BY3-2119G 1956-57 Chevrolet ...... £40.13 BY4-2123G 1964-65 Must-9/16” shackle blts ...... £69.38 BY3-2101G 1968-74 Nova/ChevyII mono leaf ...... £53.65 BY4-2101G 1966-73 Must-1/2” shackle blts ...... £71.23 BY3-2103G 1968-79 Nova/ChevyII multi leaf ...... £58.90

COMPETITION ENGINEERING REAR SUSPENSION

C.E. LADDER BAR CROSSMEMBER KIT Designed to provide a sturdy mounting point for the ladder bar front rod-end. Capable of withstanding the abuse of a racing suspension while adding strength to the chassis. The 54” wide bar also acts as a rear prop-shaft loop. Includes brackets & bolts. Welding required. BY2019 Ladder bar crossmember ...... £88.55

CE DIAGONAL LINK CE LADDER LINK [BARS] Allows the racer to fine tune the suspension without re- Eliminates side to side housing movement. Superior to the Panhard bar for moving the bar from the car. Pivoting lower adjusters elimi- eliminating sway in ladder bar & four link suspensions. This bolt on diago- nate the bind found in some bars. 1” x .156” DOM tube. nal link can be used with the CE Ladder Bars, Ladder Links & Std 4-links Forged solid rear rod ends. 33.5” overall. High quality al- with 3/4” mounting holes. Made from 3/4” x .156” mild steel tube. Kit in- loy spherical front rod ends. Black powder coated. Weld- cludes rod ends & mounting hardware. ing required. BY2052 Bolt on diagonal link 36.5” ...... £86.41 BY2005 Ladder link kit inc ends ...... £395.45 CE 4-LINK KIT CE ROD ENDS- 3/4” HOLE Offers better adjustability over a ladder bar suspension for in- Static radial load capacity- low carbon steel- 14,290lbs. chrome creased performance. By locating the bars with the various mount- moly steel- 28,090lbs. ing holes in the brackets, you can create an instant centre that is correct for your car. 17-1/4” long, 1” diam x .156” threaded BY6011 Low carbon steel 3/4” RHT ...... £15.98sp links. 3/16” thick brackets. Includes 8 chrome-moly rod ends. BY6012 Low carbon steel 3/4” LHT ...... £15.98sp Inc’ hardware.Requires welding. BY6130 Chrome moly steel 3/4” RHT ...... £6.75sp BY2017 Rear four link kit ...... £318.83 BY6131 Chrome moly steel 3/4” LHT ...... £26.81sp

CE PANHARD BAR KIT CE LOWER COIL-OVER SHOCK MOUNT KIT Eliminates side to side rear axle housing movement within the chassis. Keeps your tyres from rubbing the wheel open- Provides a solid adjustable mounting point for coil over ings, making sure you get down the track in a straight line. shockabsorbers. Fits housings with 3” OD axle tubes. Has Perfect for street driven vehicles. 30” tube can be trimmed 6” of height adjustment in 1/2” increments. 1/4” thick hous- to fit. Includes gusseted mounting brackets & rod ends. ing brackets, 3/16” thick shock brackets. Includes hard- Hardware & instructions included. Welding required. ware & spacers. Welding required. Kit is for qty 2. BY2037M Panhard bar kit ...... £126.19 BY2047 Lower coil-over mount kit-pr ...... £78.84pr

CE BOLT-ON PROP-SHAFT SAFETY LOOP CE PROFESSIONAL WHEEL-E BARS Wheelstands may look spectacular but they can actually hurt performance. Contains the propshaft and prevents flipping the vehicle in the event of a front u/j failure. Manufactured from CNC Although some front end lift is beneficial for weight transfer, excessive lift can slow forward motion. When a car wheelstands upon initial launch, it formed 1/4” thick, 2” wide mild steel. Mounts to the uses up power that could propel the vehicle forward. This results in slower floorpan with four bolts per side. Zinc plated. ET’s. Wheel-E-bars are designed to limit & control big wheelstands without unloading the rear tyres. As the rear housing rotates, the natural rubber wheels BY3028 Safety loop ...... £59.05 come in contact with the track. The shock of this contact is absorbed by both the lower aluminium struts & the coil spring upper struts which keep the tyres from unloading. As the housing continues to rotate more & the front CE UPPER COIL-OVER SHOCK MOUNT KIT end begins to lift, the coil springs on the upper struts start to compress. The Designed to mount between the rear frame rails Street Rod, more that the springs are compressed, the more force they exert against the Pro-Street, Drag Race application. Includes one 40” long x housing rotation, eventually overcoming the rising force of the front end and 1.625” mounting tube, .188” thick mounting brackets, 4 gently pushing it back down. This converts the rotational energy into for- shock mount tabs, 4 shock spacers for older style coil-over ward motion, resulting in quicker ET’s. Overall length is 44” & the centre to shocks and all mounting hardware. Welding required. centre mounting bracket distance is 22-11/16”. BY2046 Upper coil-over mount kit ...... £49.31 BY2016 Chrome wheel-e-bars ...... £429.34 S12/10 - SUSPENSION - S12/10 -Rear Suspension/Air-Ride-

HEIDTS REAR SUSPENSION

HEIDTS 4 BAR- FORD CLASSIC TRUCK

Replaces old leaf springs. Gives a much better ride, & better cornering. Will need Panhard rod, coil overs & coil springs

BYAJW775 Ford p/up 1953-56 F100 weld in ...... £832.45 HEIDTS 4 BAR- CHEVY CLASSIC TRUCK Replaces old leaf springs. Gives a much better ride, & better cornering. Will need Panhard rod, coil overs & coil springs. 1/2 ton only! BYAJW755 Chevy p/up 1947-53 weld in ...... £993.53 Above kit is for 1/2 ton, will not fit 3/4 ton BYAJW765 1955-59 2nd series-weld in ...... £918.29

PANHARD ROD FOR HEIDTS 4 BAR REAR COIL OVERS HEIDTS CLASSIC TRUCK 4 BAR

Required for Heidts 4 bar for Classic Truck. Weld on. BYAJW780 Weld on-except ‘47-54 Chevy ...... £144.16 BYAJW785 Weld on- 1947-54 Chevy only ...... £156.71 BYAJW790 Black- non adj damping ...... £337.60

HEIDTS REAR COIL 4 BAR SPRINGS REAR ANTI-ROLL BAR KIT

For use with Heidts 4 bar rear for Classic Truck

BYAJW795 11” black rear coil springs 250lb ...... £155.54 BYAJW440 Chevy 55-57 std suspension only ..... £213.16 BYAJW800 11” black rear coil springs 300lb ...... £155.54 Above kit has a 7/8” diameter bar with Urethane bushes HEIDTS REAR 4 BAR KITS SUBFRAME CONNECTORS MUSTANG COUPE 64-70 Bolt on subframe connectors help eliminate bending, flexing & This is a bolt on kit [apart from the rear axle case brackets] cracking of spot-welded sheet metal panels. They also tie the front complete with coil overs and springs. Does not include axle & rear frames together creating a solid platform for increased housing. performance levels. For use with Heidts rear 4 bar kit.

BYAJW340 Mustang 1964-70 ...... £1912.10 BYAJW350 Subframe connectors 64-70 ...... £309.82

AIR-RIDE REAR SUSPENSION

AIR BAG-Double Convoluted

The capacity of this unit is 2140lbs @ 100psi. Minimum height 3”, installed height 4.5 to 5”. Maximum height 7”. Diameter [inflated] 6.5”. 1/4 npt connection.

BY90006781 ...... pr £120.59sp

AIRBAR BOLT-IN 4 LINK 1955-57 CHEVY This 4 bar unit is designed for the Tri-Chevy. It is complete with upper and lower mounts for “Shockwaves”. there are two types of chassis used- one piece section & 2 piece section. We can make up either type. BY11027199 For one piece chassis ...... £962.76sp BY90000557 C/member for 2 piece ...... £245.76sp

REAR SHOCK UPPER BRACKET/MOUNT REAR UPPER-CROSSMEMBER-SHOCKS

Includes axle mounts & weld in upper shock crossmember. Does not include Brackets/mounts for Shock. shockabsorbers.

BY90000034 Shock bracket-rear upper ...... £17.38 BY11009099 Upper c/member mount ...... £155.64 S12/11 - SUSPENSION/AIR RIDE SYSTEM/REAR AXLE - S12/11 Air-Ride-Rear Axle-Propshaft Parts

AIR-RIDE TANKS/PUMPS etc

MANUAL AIR-RIDE SYSTEM RIDE PROe3 AIR-RIDE SYSTEM The original RidePro system utilizes a quality solenoid air valve system & The RidePROe3 system provides automatic adjustment with the use of an dependable electric components to provide simple, & reliable control. Con- ECU & digital display. Rise time 3-5 seconds. [BY30334100 3 seconds]. 2- trol panel provides simple & accurate inflate / deflate control for each 327 Thomas compressors, ARV4000 airvalve, 1/4” airline & fittings, elec- airspring. Vehicles up to 3500lbs. Rise time 3-5 seconds. 327 Thomas com- tronic control. Relies solely on air pressure sensors for each spring, to adjust pressor, ARV4000 airvalve, 1/4” airline & fittings, electronic control. the ride height. Three presets. LevelPRO height sensors available also.

BY30154000 Manual system- 3 gallon tank ...... £1027.12sp BY30334000 RideproE3 >3500lb-3 gal tank ...... £1211.86sp

REAR AXLE

DIFF CARRIER GASKET ARP CW & PINION BOLTS

For Ford 9", 7/16" x 0.940". Special hardened, precision ground BYP27944 GM 12 bolt £5.44 washers are included. 200,000 PSI. BYP27807 8” Ford £7.22 BYP27929 9" Ford £7.54 BY250-3002 Ring gear bolt kit ...... £34.15 kit

INSTALLATION KIT

Motive Gear installation kits provide most of the parts required for a crownwheel & pinion change. Kit contents vary. Ask salesperson for exact contents of the kit you require.

BYR9RMK Ford 9" ...... £118.37 kit PROPSHAFT PARTS These U-Joint Girdles provide more bearing surface for the Universal Joint Bearing cap which increases its load bearing capacity. Manufactured from 7075-T6 aluminium with a Anodized finish.

GM U-JOINT GIRDLE

BY85800 55-82 - U Bolts type ...... £39.20 BY85810 65-82 - 12 bolt straps ...... £40.22

DANA -U-JOINT GIRDLE FORD- U -JOINT GIRDLE

BY85800 Dana 60 U-Bolt type ...... £38.40 BY85860 Ford 9" ...... £39.55 - SHOCKABSORBERS - S12/12 HD Shocks for std OEM Cars S12/12

SHOCKABSORBERS

These shockabsorbers [RQ] have been designed & tuned for optimum ride quality in Street Rods, Muscle Cars, Classic Trucks & Cruisers. It’s the perfect solution for the hotrodder who wants to install it & forget it. they are designed to replace the OEM shockabsorbers & the vehicle must have the stock suspension & ride height. These shockabsorbers are made in Indiana in the USA, not Mexico or China. They are an impact forged, aluminium mono-tube design. Here are some features- Mono-tube design allows a large piston for superior oil control- increases ride quality & handling performance. It also uses less components than a twin-tube design for superior fluid control. The Teflon piston wiper allows consistent piston/bore contact & repeatable performance. There is a specially contoured composite gas separator cup which optimizes dead length & ensures proper nitrogen/oil separation. Externally, the body is hard coat anodized for years of lasting beauty & performance. There is an integral internal bumpstop which eliminates extension crashing. The main piston rod is a 1/2” hardened shaft precision ground & straightened to a tolerance of .001” for increased durability & performance. A billet end cap with integrated debris wiper helps to prevent seal damage. The oversized rod guide improves piston rod stability.

FRONT SHOCKABSORBERS REAR SHOCKABSORBERS

BY22049846 1967-69 Camaro ...... £94.40sp ea 1984-87 Corvette ...... 1989-96 Corvette 1968-79 Nova ...... 1968-72 Chevelle 1978-88 Malibu G-body BY22049857 1963-82 Corvette ...... £94.40sp ea

FRONT SHOCKABSORBERS REAR SHOCKABSORBERS

BY22069846 1988 Corvette ...... £90.50sp ea 1958-64 Impala ...... 1964-67 Chevelle BY22099854 1955-57 Chevy ...... £90.50sp ea 1957-58 Fairlane ...... 1987-96 Dodge Dakota 1950-55 “C” GM Truck ...... 1965-70 Galaxie

REAR SHOCKABSORBERS

BY22089844 1958-64 Impala ...... £90.50sp ea

REAR SHOCKABSORBERS

BY22099867 1962 Dodge Dart ...... £85.77sp ea 1965-72 Charger ...... 1973-76 Charger 1968-70 B-Body ...... 1970-74 E-Body