Installation Guide the NISS4HT Firmware for DBALL2 Is an All-In-One Door Lock and Override Module Compatible with Specific Infiniti and Nissan Vehicles

Platform: DBALL2

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.

Installation Guide The NISS4HT firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Infiniti and Nissan vehicles. This guide supports the installation of a DBALL2 in Remote Start Ready (RSR) mode with or without a Plug & Play THNISS3 T-Harness. This solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF System or SmartStart (all sold separately).

Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance.

Important! This product is NOT compatible with vehicles equipped with a manual transmission. This guide is compatible with the NISS4HT firmware version 2.20 and higher.

Index Vehicle Application Guide...... 02

Key2GO & 1KEY...... 03

Installation (Wiring Diagrams & Vehicle Wiring Reference Charts) Type 1 - with THNISS3 T-Harness...... 04 Type 1 - without T-Harness...... 05 Type 2 - with THNISS3 T-Harness...... 09 Type 2 - without T-Harness...... 10 Type 3 - with THNISS3 T-Harness...... 12 Type 3 - without T-Harness...... 13 Type 4 - with THNISS3 T-Harness...... 15 Type 4 - without T-Harness...... 16 SmartStart/XL202 Installation Notes...... 18

Programming [1] (-) Unlock Output: Black/White Module Programming...... 19 (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White Module Reset...... 21 (-) RAP Off Output: Red/Black Hard Reset...... 21 See Feature & Option List...... 22 Vehicle Wiring Reference Chart Feature Programming...... 23

LED Diagnostics & Troubleshooting...... 24 Parking Light Error Codes...... 26

Limited One-Year Consumer Warranty...... 27

Quick Reference Guide...... 28 SmartStart Compatible SmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information.

® Infiniti & Nissan are registered trademarks and property of their respective companies.

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 2 Vehicle Application Guide The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more information on installation wiring, programming and troubleshooting for these vehicles. M d ' E q O g e n g R i n s e i y l n u i s n e b i i l s r u P t K o n e l P i a r h g t o r o p r P c n n t o t N r r e m o n o n a o i ) e s o c a o D H t o e v s P y t c / C i r a t r k r a D l i k e d r e a p n a D o n D P t r - y L v o r u k s o o i t y u t l l i t t b s i S L r o c c a r t

Vehicles r ( d n o o i u s S t e o e l r r A D H T u l l ( a o n t t p a o o T s S t c n e e g r n n g g g g p C o I u t P u e R f U o o R R n n n n t y y ( i i i i n t s r s S A O O r r r r a r t t C C B o y h t o r u s o o o o t a T T h t t r r r y i c t t t t k t a C u S i i i i r r t t M g c t a o o S ) S t e i c r t S n n n n o o a a k o o e P a e z i S L t o a i t o o o o t l r S K K t l F c H s o c D D R i o n e g S o P n / C C S M M M M a T t n b / t n g g L U e m r m i o r o o F e O O r k y y y y i n n h ) h s r r e e k i i a r r r r t k O L L a n i r s e m t t t t m c y o o v d d R t a m i s i i u n a u e m n n n n G a r e r i o o r l l x x r o m g 2 I P P 3 3 R S T E E E E 6 5 4 3 2 1 0 9 B I K A D D D D S S T M ------y m 1 1 1 1 1 1 1 0 E K V L L L L L L L L e K S S e S S S S S S S T T T 0 0 0 0 0 0 0 0 2 2 2 2 2 2 2 2 P A D D D D D D D D K P R O R R R R R S S S S S S S Infiniti M35h (Smart Key)* 1 1 • • • • • • • • • • • • • • • • • • • • • • M37 (Smart Key) 1 1 1 • • • • • • • • • • • • • • • • • • • • • • M56 (Smart Key) 1 1 1 • • • • • • • • • • • • • • • • • • • • • • Q70 (Smart Key) 1 1 1 • • • • • • • • • • • • • • • • • • • • • • QX56 (Smart Key) 1 1 1 • • • • • • • • • • • • • • • • • • • • • • QX80 (Smart Key) 1 1 1 • • • • • • • • • • • • • • • • • • • • • • Nissan Cube (Smart Key) 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • • • • JUKE (Smart Key) 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • • • • LEAF (Smart Key) 2 • • • • • • • • • • • • • • • • • • • • • • Quest (Smart Key) 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • • • • • • Sentra (Smart Key) 1 1 1 1 • • • • • • • • • • • • • • • • • • • • • • Versa (Smart Key) 3 3 3 3 • • • • • • • • • • • • • • • • • • • • • • Versa Note (Smart Key) 4 4 4 • • • • • • • • • • • • • • • • • • • • • • * The Infiniti M35h (Smart Key) is not compatible with the THNISS3D T-Harness.

Legend: AV: Horn & Lights Controls RS: Remote Start & Engine Controls DL: OE Door Lock & Alarm Controls SS: Integrated Security & Monitoring PK: Transponder & Immobilizer Override ST: Function/Feature Status

When armed, the aftermarket alarm (if available) will sound if the trunk is opened using the OEM passive entry request button near the trunk. To avoid this, open the trunk using the OEM fob button, aftermarket transmitter or SmartStart application. Alternately, you can disarm the aftermarket alarm before opening the trunk. [1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 3

This feature is mandatory to control the immobilizer override in this firmware. Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses an array of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to give up a key. The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle. All Key2GO-compatible firmware are clearly indicated in the function list of each vehicle search result page and will also appear on the flash page. Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name. Key2GO is compatible with XpressVIP 4.5 or higher and requires an XKLoader. Refer to page 20 of this guide for instructions on how to program features using Key2GO.

[1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 4 Installation Type 1 - with THNISS3 T-Harness

Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

Parking light output MUST be controlled through data when using Optional T-Harness, See Feature & Option List section to enable this feature. Hood Pin PTS - Brown or White 8-pin conn. (at PTS switch) (-) Driver Door Trigger: Pin 47 Note: hood pin only 1 2 3 required on vehicles not 41 42 43 44 45 46 47 48 49 equipped with a factory 4 5 6 7 8 hood pin. 50 51 52 53 54 55 (-) PTS: [2] (-) PTS: Lt.Green, pin 8 Pin 4 Junction - White/Black Black 15-pin conn. (left of steering column) Remote Start Safety OR Override Switch

NOT USED 14 T-01 T-01

T-02 T-02 10 12 [1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black

Clock & Data Wire 2 RF at NATS Connector 4 (behind Push-to-Start button) Prog. Button DBALL2 See See Vehicle Wiring Reference LED Chart for wire location. Vehicle Wiring Reference Chart

T-Harness THNISS3

B-01 B-02 B01 B02 Q70 (Smart Key) M37 (Smart Key) [1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black QX80 (Smart Key) M56 (Smart Key) Diagnostic Connector OBDII [1] (-) Lock Output: Green/White Cube (Smart Key) QX56 (Smart Key) (connector side view) (-) RAP Off Output: Red/Black 2011-2015 JUKE (Smart Key) OR 2016 JUKE (Smart Key) See 1 8 Quest (Smart Key) Vehicle Wiring Reference Chart 9 16 Sentra (Smart Key)

Diagnostic Connector OBDII (connector side view)

Brake Pedal You can connect to either a XL202 Brake Switch RFTD OR a SmartStart module. T-Harness Refer to the SmartStart/XL202 Installation Notes for more information.

Important! Always connect OBDII connector BEFORE all other connections. [1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section. [2] This connection is only for the Nissan JUKE and Nissan Sentra.

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 5 Installation Type 1 - without T-Harness

Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

(-) Lock, (-) Unlock wires & Parking Light Junction - White 15-pin conn. PTS - Brown or White 8-pin conn. See Vehicle Wiring Reference Chart. (left of steering column) (at PTS switch) 56 57 58 59 60 61 62 63 64 1 2 3 65 66 67 68 69 70 4 5 6 7 8 Lock, Unlock and Parking Light wires must be connected if the door (-) PTS: (+)12V: Pin 70 (-) PTS: [2] lock and OEM alarm are not Pin 4 Lt.Green, pin 8 controlled by data. See features 5 & 7 in Feature and Option List section. OR Junction - Black 15-pin conn. (left of steering column) 48 41 42 43 44 45 46 47 49 Diagnostic connector OBDII HS CAN High: Blue, pin 6 50 51 52 53 54 55 (connector side view)

1 8 (-) Driver Door Note: Hood pin only required Trigger: Pin 47 9 16 on vehicles not equipped with a factory hood pin. HS CAN Low: Pink, pin 14 Hood Pin

HS CAN High: Tan/Black: 3 HS CAN Low: Tan: 4 Immo. Data Interrupt (veh.side): Yellow: 8

Immo. Data Interrupt (conn.side): Orange/Yellow: 9 14 (+) 12V: Yellow/Red: 11 Remote Start Safety [1] (+) Parking Lights Output: Brown/Red: 12 Override Switch (+) 12V: Red: 13 (-) Ground: Black: 14

[1] (-) Unlock Output: Black/White: 1

(-) Push-To-Start Output: Green/Black: 2 10

[1] (-) Lock Output: Green/White: 3 12 6: White/Black: (-) Hood (-) RAP Off Output: Red/Black: 4 (+) Brake Activation Output: Gray: 6 Immo. Clock Output: Yellow/Black: 10 Immo. Data Output (veh.side): Orange/Black: 11 2 White 4-pin conn. RF (+) 12V (brake switch) 4 Prog. Button DBALL2 [1] (-) Unlock Output: Black/White 86 87 85 (-) PTS Output: Green/Black LED 87a 3 4 [1] (-) Lock Output: Green/White 30 1 2 (-) RAP Off Output: Red/Black See (+) Brake: Pin 2 Vehicle Wiring Reference Chart

You can connect to either a XL202 RFTD OR a SmartStart module. Refer to the SmartStart/XL202 Data: Pin 3 Installation Notes for more information. CUT

N.A.T.S Antenna Connector (behind Push-to-Start button) Clock: Pin 2

[1] Only connect if you disable corresponding feature (see Feature & Option List section). [2] This connection is only for the Nissan JUKE and Nissan Sentra. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 6 Type 1 - Vehicle Wiring Reference Chart

Connector Information Function Color Pin Polarity Location Color Pins Infiniti M35h (Smart Key) 2012-2013 Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Brown 4 (-) Push-to-Start button connector. Brown 8 12V White 70 (+) BCM left of steering column. White 15 Driver Door Trigger Lt.Green 47 (-) BCM left of steering column. Black 15 Brake Violet 2 (+) Brake connector. White 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Lock Brown 15 (-) Power window main switch. White 16 Unlock Gray 16 (-) Power window main switch. White 16 Parking Lights Blue 2 (+) Drivers kick. White 10 or 12 Infiniti M37 (Smart Key) 2011-2013 Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Brown 4 (-) Push-to-Start button connector. Brown 8 12V White 70 (+) BCM left of steering column. White 15 Driver Door Trigger Lt.Green 47 (-) BCM left of steering column. Black 15 Brake Violet 4 (+) Brake connector. White 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Lock Brown or Red 15 (-) Power window main switch. White 16 Unlock Green or Gray 16 (-) Power window main switch. White 16 Parking Lights Blue 4 (+) Drivers kick. White 10 or 12 Infiniti M56 (Smart Key) 2011-2013 Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Brown 4 (-) Push-to-Start button connector. Brown 8 12V White 70 (+) BCM left of steering column. White 15 Driver Door Trigger Lt.Green 47 (-) BCM left of steering column. Black 15 Brake Violet 2 (+) Brake connector. White 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Lock Red or Brown 15 (-) Power window main switch. White 16 Unlock Green or Gray 16 (-) Power window main switch. White 16 Parking Lights Blue 4 (+) Drivers kick. White 10 or 12 Infiniti Q70 (Smart Key) 2014-2016 Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Brown 4 (-) Push-to-Start connector. Brown 8 12V White 70 (+) BCM left of steering column. White 15 Driver Door Trigger Lt.Green 47 (-) BCM left of steering column. Black 15 [1] (-) Unlock Output: Black/White Brake Violet 2 (+) Brake connector. White 4 (-) PTS Output: Green/Black HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 See Lock Red or Brown (hybrid) 15 (-) Power window main switch. White 16 Vehicle Wiring Reference Chart Unlock Green or Gray (hybrid) 16 (-) Power window main switch. White 16 Parking Lights Blue 4 or 2 (+) Drivers kick. White 12 Infiniti QX56 (Smart Key) 2011-2013 Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Lt. Green/Red 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Lt.Blue 4 (-) Push-to-Start connector. Brown 8 12V Yellow 70 (+) BCM left of steering column. White 15 Driver Door Trigger Gray/Red 47 (-) BCM left of steering column. Black 15 Brake Red 2 (+) Brake connector. White 2 or 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Lock Red 4 or 15 (-) Power window main switch. White 16 Unlock White 5 or 16 (-) Power window main switch. White 16 Parking Lights Blue/Orange 8 (+) Dash fuse box. White 10

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 7 Type 1 - Vehicle Wiring Reference Chart

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Infiniti QX80 (Smart Key) 2014-2016 Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Lt. Green/Red 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Lt.Blue 4 (-) Push-to-Start connector. Brown 8 12V Yellow 70 (+) BCM left of steering column White 15 Driver Door Trigger Gray/Red 47 (-) BCM left of steering column. Black 15 Brake Red 2 (+) Brake connector. White 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Lock Red 15 (-) Power window main switch. White 16 Unlock White 16 (-) Power window main switch. White 16 Parking Lights Blue/Orange 8 (+) Drivers kick. White 10 Nissan Cube (Smart Key) 2009-2014 Clock Pink/Blue 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Lt. Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Blue/Orange 4 (-) Push-to-Start connector. Brown 8 12V Yellow 70 (+) BCM left of steering column. White 15 Driver Door Trigger Brown/Yellow 47 (-) BCM left of steering column. Black 15 Brake White 2 (+) Brake connector. White 2 or 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Lock White/Black 8 (-) BCM behind dash fuse box. Black 40 Unlock White/Red 7 (-) BCM behind dash fuse box. Black 40 Parking Lights Brown/White 13 (+) Drivers kick. White 16 Nissan JUKE (Smart Key) 2011-2016 Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Lt. Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Lt.Green 8 (-) Push-to-Start connector. Brown 8 12V Yellow 70 (+) BCM left of steering column White 15 Driver Door Trigger Lt.Blue 47 (-) BCM left of steering column. Black 15 Brake Red 2 (+) Brake connector. White 2 or 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Lock Red 8 (-) BCM behind dash fuse box. Black 40 Unlock Blue 7 (-) BCM behind dash fuse box. Black 40 Parking Lights Violet 70 (+) Drivers kick. White 100 Nissan Quest (Smart Key - w/o Power Sliding Door) 2011-2014 Clock Red 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data White 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Violet 4 (-) Push-to-Start connector. Brown 8 12V Blue 70 (+) BCM behind instrument cluster. White 15 Driver Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15 Brake Lt.Green 2 (+) Brake connector. White 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16

Lock Gray 12 (-) BCM behind instrument cluster. Black 40 [1] (-) Unlock Output: Black/White Unlock Brown 13 (-) BCM behind instrument cluster. Black 40 (-) PTS Output: Green/Black Parking Lights Red/Blue 8 (+) Dash fuse box. White 10 [1] (-) Lock Output: Green/White Nissan Quest (Smart Key - w/o Power Sliding Door) 2015-2016 (-) RAP Off Output: Red/Black Clock Gray 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Pink 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 See Vehicle Wiring Reference Chart PTS Violet 4 (-) Push-to-Start connector. Brown 8 12V Blue 70 (+) BCM behind instrument cluster. White 15 Driver Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15 Brake Lt.Green 2 (+) Brake connector. White 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Lock Gray 12 (-) BCM behind instrument cluster. Black 40 Unlock Brown 13 (-) BCM behind instrument cluster. Black 40 Parking Lights Red/Blue 8 (+) Dash fuse box. White 10

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 8 Type 1 - Vehicle Wiring Reference Chart

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Nissan Quest (Smart Key - w/ Power Sliding Door) 2011-2014 Clock Red 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data White 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Violet 4 (-) Push-to-Start connector. Brown 8 12V Blue 70 (+) BCM behind instrument cluster. White 15 Driver Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15 Brake Lt.Green 2 (+) Brake connector. White 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Lock Yellow 8 (-) BCM behind instrument cluster. Black 40 Unlock White 7 (-) BCM behind instrument cluster. Black 40 Parking Lights Red/Blue 8 (+) Dash fuse box. White 10 Nissan Quest (Smart Key - w/ Power Sliding Door) 2015-2016 Clock Gray 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Pink 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Violet 4 (-) Push-to-Start connector. Brown 8 12V Blue 70 (+) BCM behind instrument cluster. White 15 Driver Door Trigger Green 47 (-) BCM behind instrument cluster. Black 15 Brake Lt.Green 2 (+) Brake connector. White 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Lock Yellow 8 (-) BCM behind instrument cluster. Black 40 Unlock White 7 (-) BCM behind instrument cluster. Black 40 Parking Lights Red/Blue 8 (+) Drivers kick. White 10 Nissan Sentra (Smart Key) 2013-2016 Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Lt. Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Lt.Green 8 (-) Push-to-Start connector. White 8 12V Yellow 70 (+) BCM left of steering column White 15 Driver Door Trigger Yellow 47 (-) BCM left of steering column. Black 15 Brake Lt.Blue to Red 2 (+) Brake connector. White 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Lock Violet 8 (-) BCM behind dash fusebox Black 40 Unlock Blue 7 (-) BCM behind dash fusebox Black 40 Parking Lights Violet 31 (+) Drivers kick. White 100

[1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 9 Installation Type 2 - with THNISS3

Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

Parking light output MUST be controlled through data when using Optional T-Harness, See Feature & Option List section to enable this feature. Hood Pin

Note: hood pin only Junction - 49 required on vehicles not Black 15-pin conn. 55 PTS - White 8-pin conn. equipped with a factory (behind glove box) 48 (at PTS switch) hood pin. 47 54 (-) Driver Door 46 53 Trigger: Lt.Blue, pin 47 1 2 3 White/Black 45 4 5 6 7 8 Remote Start Safety 44 52 Override Switch (-) PTS: Lt.Blue, pin 8 43 51 42 41 50 14 NOT USED

T-01 T-01 10 [1] (-) Unlock Output: Black/White 12 (-) Push-To-Start Output: Green/Black [1] (-) Lock Output: Green/White T-02 T-02 (-) RAP Off Output: Red/Black

2 RF 4 Prog. Button DBALL2 See LED Vehicle Wiring Reference Chart

Clock & Data Wire at NATS Connector (behind Push-to-Start button) T-Harness See Vehicle Wiring Reference THNISS3 Chart for wire location.

B01 B-01 B-02 LEAF (Smart Key) [1] (-) Unlock Output: Black/White Diagnostic Connector (-) PTS Output: Green/Black OBDII [1] (-) Lock Output: Green/White NOT USED (connector side view) (-) RAP Off Output: Red/Black See 1 8 Vehicle Wiring Reference Chart

9 16

Diagnostic Connector OBDII (connector side view)

You can connect to either a XL202 RFTD OR a SmartStart module. Brake Pedal Brake Switch Refer to the SmartStart/XL202 T-Harness Installation Notes for more information.

Important! Always connect OBDII connector BEFORE all other connections.

[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 10 Installation Type 2 - without T-Harness

Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

(-) Lock, (-) Unlock wires & Parking Light Junction - White 15-pin conn. See Vehicle Wiring Reference Chart. (behind glove box) 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 PTS - White 8-pin conn. (at PTS switch) Lock, Unlock and Parking Light wires must be connected if the door (+)12V: Yellow, pin 70 lock and OEM alarm are not 1 2 3 controlled by data. See features 5 & 7 in 4 5 6 7 8 Feature and Option List section.

(-) PTS: Lt.Blue, pin 8 Junction - Black 15-pin conn. (behind glove box) 48 41 42 43 44 45 46 47 49 Diagnostic connector OBDII HS CAN High: Blue, pin 6 50 51 52 53 54 55 (connector side view)

1 8 (-) Driver Door Trigger: Lt.Blue, pin 47 9 16 Note: Hood pin only required HS CAN Low: Pink, pin 14 on vehicles not equipped with a factory hood pin.

Hood Pin HS CAN High: Tan/Black: 3 HS CAN Low: Tan: 4 Immo. Data Interrupt (vehicle side) Yellow: 8 14 Immo. Data Interrupt (conn.side): Orange/Yellow: 9 (+) 12V: Yellow/Red: 11 [1] (+) Parking Lights Output: Brown/Red: 12 (+) 12V: Red: 13 Remote Start Safety (-) Ground: Black: 14 Override Switch

[1] (-) Unlock Output: Black/White: 1

(-) Push-To-Start Output: Green/Black: 2 10

[1] (-) Lock Output: Green/White: 3 12 6: White/Black: (-) Hood (-) RAP Off Output: Red/Black: 4 (+) Brake Activation Output: Gray: 6 Immo.Clock Output: Yellow/Black: 10 Immo. Data Output (veh.side): Orange/Black: 11 2 White 4-pin conn. RF (+) 12V (brake switch) 4 Prog. Button DBALL2 [1] (-) Unlock Output: Black/White 86 87 85 (-) PTS Output: Green/Black LED 87a 3 4 [1] (-) Lock Output: Green/White 30 1 2 (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart (+) Brake: Lt.Blue or Brown, pin 2 You can connect to either a XL202 RFTD OR a SmartStart module. Refer to the SmartStart/XL202 Data: Lt.Green, pin 3 Installation Notes for more information. CUT

N.A.T.S Antenna Connector (behind Push-to-Start button) Clock: Pink, pin 2

[1] Only connect if you disable corresponding feature (see Feature & Option List section). With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 11 Type 2 - Vehicle Wiring Reference Chart

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Nissan LEAF (Smart Key) 2014 Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Lt. Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Lt.Blue 8 (-) Push-to-Start connector. White 8 12V Yellow 70 (+) BCM behind glove box.. White 15 Driver Door Trigger Lt.Blue 47 (-) BCM behind glove box.. Black 15 Brake Lt.Blue or Brown 2 (+) Brake connector. White 4 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Parking Lights Blue or White 30 (+) Drivers kick. White 32 Lock Red 8 (-) BCM behind glove box. Black 40 Unlock Gray 7 (-) BCM behind glove box. Black 40

[1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 12 Installation Type 3 - with THNISS3 T-Harness

Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

Parking light output MUST be controlled through data when using Optional T-Harness, See Feature & Option List section to enable this feature. Hood Pin BCM PTS - Brown 8-pin conn. Black 24-pin conn. (PTS switch) (left of steering column) Note: hood pin only required on vehicles not 24 12 equipped with a factory 23 11 hood pin. 4 3 2 1 22 10 5 6 7 21 9 8 20 8 White/Black (-) Driver Door Trigger: Lt.Blue, pin 18 19 7 18 6 Remote Start Safety 17 5 Override Switch (-) PTS: Blue, pin 8 16 4 15 3 14 2 13 1 NOT USED 14 T-01 T-01

T-02 T-02 10

[1] (-) Unlock Output: Black/White 12 (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black

Clock & Data Wire 2 RF at NATS Connector 4 (behind Push-to-Start button) Prog. Button DBALL2 See See Vehicle Wiring Reference LED Chart for wire location. Vehicle Wiring Reference Chart

T-Harness THNISS3

B01 B-01 B-02 Versa (Smart Key) [1] (-) Unlock Output: Black/White Diagnostic Connector (-) PTS Output: Green/Black OBDII [1] (-) Lock Output: Green/White NOT USED (connector side view) (-) RAP Off Output: Red/Black See 1 8 Vehicle Wiring Reference Chart

9 16

Diagnostic Connector OBDII (connector side view)

You can connect to either a XL202 RFTD OR a SmartStart module. Brake Pedal Brake Switch Refer to the SmartStart/XL202 T-Harness Installation Notes for more information.

Important! Always connect OBDII connector BEFORE all other connections.

[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 13 Installation Type 3 - without T-Harness

Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

(-) Lock, (-) Unlock wires & Parking Light See Vehicle Wiring Reference Chart. (+)12V: Green, pin 1 1 PTS - Brown 8-pin conn. 2 (PTS switch) Lock, Unlock and Parking Light Black connector wires must be connected if the door (drivers kick) lock and OEM alarm are not 4 3 2 1 controlled by data. See features 5 & 7 in BCM 5 6 7 8 Feature and Option List section. Black 24-pin conn. (at drivers kick) (-) PTS: Blue, pin 8 24 12 23 11 22 10 (-) Driver Door 21 9 Diagnostic connector OBDII HS CAN High: Blue, pin 6 Note: Hood pin only required Trigger: 20 8 (connector side view) on vehicles not equipped with Lt. Blue, pin 18 19 7 18 6 1 8 a factory hood pin. 17 5 9 16 16 4 Hood Pin 15 3 14 2 HS CAN Low: Pink, pin 14 13 1

HS CAN High: Tan/Black: 3 HS CAN Low: Tan: 4 Remote Start Safety Override Switch Immo. Data Interrupt (vehicle side): Yellow: 8 14 Immo. Data Interrupt (conn.side): Orange/Yellow: 9 (+) 12V: Yellow/Red: 11 [1] (+) Parking Lights Output: Brown/Red: 12 (+) 12V: Red: 13 (-) Ground: Black: 14 [1] (-) Unlock Output: Black/White: 1

(-) Push-To-Start Output: Green/Black: 2

[1] (-) Lock Output: Green/White: 3 10 12 6: White/Black: (-) Hood (-) RAP Off Output: Red/Black: 4

(+) Brake Activation Output: Gray: 6

Immo.Clock Output: Yellow/Black: 10

Immo. Data Output (veh. side): Orange/Black: 11

2 RF (+) 12V 16 7 4 15 6 Prog. Button DBALL2 [1] (-) Unlock Output: Black/White 86 87 85 (-) PTS Output: Green/Black 14 5 LED 87a [1] (-) Lock Output: Green/White 30 13 4 (-) RAP Off Output: Red/Black 12 See Vehicle Wiring Reference Chart 11 10 3 9 2 Junction - You can connect to either a XL202 (+) Brake: Lt.Green, pin 9 White 16-pin conn. RFTD OR a SmartStart module. 8 1 (drivers kick) Refer to the SmartStart/XL202 Installation Notes for more information. CUT Data: Lt.Green, pin 3

N.A.T.S Antenna Connector (behind Push-to-Start button) Clock: Pink, pin 2

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 14 Type 3 - Vehicle Wiring Reference Chart

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Nissan Versa (Smart Key) 2013-2016 Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Lt.Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Blue 8 (-) Push-to-Start connector. Brown 8 12V Green 1 (+) Driver kick. Black 2 Driver Door Trigger Lt.Blue 18 (-) Driver kick. Black 24 Brake Lt.Green 9 (+) Driver kick. White 16 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Parking Lights Red 4 (+) Drivers kick. Gray 16 Lock Gray 8 (-) BCM above drivers kick. Black 40 Unlock White 7 (-) BCM above drivers kick. Black 40

[1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 15 Installation Type 4 - with THNISS3 T-Harness

Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

Parking light output MUST be controlled through data when using Optional T-Harness, See Feature & Option List section to enable this feature. Hood Pin

PTS - White 8-pin conn. 24 12 Note: hood pin only ( at PTS switch) 23 11 required on vehicles not 22 10 equipped with a factory 21 9 hood pin. 20 8 Junction - 4 3 2 1 (-) Driver Door Trigger: 19 7 White connector 5 6 7 Lt.Blue, pin 18 (at drivers kick) 8 18 6 White/Black 17 5 (-) PTS: Blue or Red, pin 8 16 4 Remote Start Safety 15 3 Override Switch 14 2 13 1

NOT USED 14 T-01 T-01

T-02 T-02 10

[1] (-) Unlock Output: Black/White 12 (-) Push-To-Start: Green/Black (-) Lock, (-) Unlock wires & [1] (-) Lock Output: Green/White Parking Light (-) RAP Off Output: Red/Black

Clock & Data Wire 2 RF

at NATS Connector 4 (behind Push-to-Start button) Prog. Button DBALL2 See Vehicle Wiring Reference LED Chart for wire location. See Vehicle Wiring Reference Chart. See features 5 & 7 in Feature and Option List section. T-Harness THNISS3

B01 B-02 Versa Note (Smart Key) B-01 [1] (-) Unlock Output: Black/White NOT USED Diagnostic Connector (-) PTS Output: Green/Black OBDII [1] (-) Lock Output: Green/White (connector side view) (-) RAP Off Output: Red/Black See 1 8 Vehicle Wiring Reference Chart

9 16

Diagnostic Connector OBDII (connector side view)

You can connect to either a XL202 RFTD OR a SmartStart module. Brake Pedal Brake Switch Refer to the SmartStart/XL202 T-Harness Installation Notes for more information.

Important! Always connect OBDII connector BEFORE all other connections.

[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 16 Installation Type 4 - without T-Harness

Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

(-) Lock, (-) Unlock wires & Parking Light See Vehicle Wiring Reference Chart.

(+)12V: Green, pin 1 1 PTS - White 8-pin conn. (PTS switch) Lock, Unlock and Parking Light 2 wires must be connected if the door Black 2-pin conn. lock and OEM alarm are not (at drivers kick) 4 3 2 1 controlled by data. See features 5 & 7 in 5 6 7 8 Feature and Option List section.

(-) PTS: Blue or Red, pin 8 Junction - White 24-pin conn. (at drivers kick)

24 12 Diagnostic connector OBDII HS CAN High: Blue, pin 6 23 11 (connector side view) Note: Hood pin only required 22 10 on vehicles not equipped with 21 9 (-) Driver Door 1 8 a factory hood pin. 20 8 Trigger: 9 16 19 7 Lt. Blue, pin 18 Hood Pin 18 6 17 5 HS CAN Low: Pink, pin 14 16 4 15 3 14 2 13 1 HS CAN High: Tan/Black: 3 HS CAN Low: Tan: 4 Remote Start Safety Immo. Data Interrupt (vehicle side): Yellow: 8 Override Switch 14 Immo. Data Interrupt (conn. side): Orange/Yellow: 9 (+) 12V: Yellow/Red: 11 [1] (+) Parking Lights Output: Brown/Red: 12 (+) 12V: Red: 13 (-) Ground: Black: 14

[1] (-) Unlock Output: Black/White: 1

(-) Push-To-Start Output: Green/Black: 2

[1] (-) Lock Output: Green/White: 3 10 6: White/Black: (-) Hood 12 (-) RAP Off Output: Red/Black: 4

(+) Brake Activation Output: Gray: 6

Immo.Clock Output: Yellow/Black: 10

Immo. Data Output (veh.side): Orange/Black: 11

2 RF (+) 12V 4 Prog. Button DBALL2 [1] (-) Unlock Output: Black/White 86 87 85 16 7 (-) PTS Output: Green/Black LED 87a 15 6 [1] (-) Lock Output: Green/White 30 14 5 (-) RAP Off Output: Red/Black See 13 4 Vehicle Wiring Reference Chart 12 11 You can connect to either a XL202 (+) Brake: Lt.Green 10 3 RFTD OR a SmartStart module. or Red, pin 9 9 2 Junction White 16-conn. Refer to the SmartStart/XL202 8 1 (at drivers kick) Installation Notes for more information.

Data: Lt.Green, pin 3 CUT

N.A.T.S Antenna Connector (behind Push-to-Start button) Clock: Pink, pin 2

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 17 Type 4 - Vehicle Wiring Reference Chart

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Nissan Versa Note (Smart Key) 2014-2016 Clock Pink 2 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 Data Lt.Green 3 Data N.A.T.S. antenna connector, behind Push-to-Start button. White 4 PTS Blue or Red 8 (-) Push-to-Start connector. White 8 12V Green 1 (+) Drivers kick Black 2 Driver Door Trigger Lt.Blue 18 (-) Drivers kick. White 24 Brake Lt.Green or Red 9 (+) Drivers kick. White 16 HS CAN High Blue 6 Data OBDII diagnostic connector. White 16 HS CAN Low Pink 14 Data OBDII diagnostic connector. White 16 Parking Lights Red to Blue 3 (+) Drivers kick. White 24 Lock Gray 8 (-) BCM, above drivers kick. Black 40 Unlock White 7 (-) BCM above drivers kick. Black 40

[1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 18 SmartStart/XL202 Installation Notes The DBALL Remote Start Ready (RSR) solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL202.

SmartStart Revision A SmartStart is optional and not included. It MUST be purchased separately. Configuration Wires (White & Brown or Blue) Cut Brown or Blue Loop OR

4 pins DBALL2 SmartStart 2 pins, CABLE not used LED D2D (4 pins, white)

The modules must be connected in a specific order. Refer to the Module Programming section for more information.

SmartStart Revision B SmartStart is optional and not included. It MUST be purchased separately. Configuration Wires (Gray & White) Connect Gray wire to (-) Ground 5 pins

4 pins DBALL2 THIS SIDE UP 2 pins, CABLE not used

D2D (4 pins, white) LED

The modules must be connected in a specific order. Refer to the Module Programming section for more information.

RF Kit The optional XL202 and antenna are not included and MUST be purchased separately. Antenna

LED DBALL2 4

XOVER XL202 4 Prog. [1] (-) Unlock Output: Black/White Button (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black 1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL2 package. 2. The modules must be connected in a specific order. Refer to the Module Programming section for more information. See Vehicle Wiring Reference Chart

RF Kit & PKE Combination Refer to the Passive Keyless Entry (PKE) Installation Guide (2102T) for detailed wiring information.

RF Kit, PKE & SmartStart BT Combination Refer to the Passive Keyless Entry (PKE) Installation Guide (2102T) for detailed wiring information.

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 19 Module Programming

Refer to the LED Diagnostics section on page 24-25 for more information and for troubleshooting purposes. Important Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step. Note: Before connecting either the XL202 or SmartStart module to DBALL2, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest version of the application. Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app. Flashing a module using your computer: Flashing a module using your smartphone or tablet 1. Connect the interface module to your computer using the 1. Connect the interface module to your XKLoader3. XKLoader2. 2. Launch the Directechs Mobile app on your smartphone or 2. Go to www.directechs.com using Internet Explorer, and tablet. select the Config for RSR button. 3. Select FLASH YOUR MODULE and follow the on screen 3. Follow the instructions to select your vehicle, installation instructions. type, and configure your options. 4. Once you have configured the firmware options, click on the FLASH button. When the flashing operation is successful, you can proceed with the programming instructions below. SmartStart Installation The DBALL2 module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBAL2L. a. To ensure that the D2D communication between SmartStart and DBALL2 works properly, SmartStart D2D the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or 10-pin Blue loop must be cut (Rev A SmartStart). b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by the DBALL2 D2D connector. Connect SmartStart to DBALL2 using the D2D port. OR

XL202 Installation D2D XL202 10-pin Connect XL202 to DBALL2 using the D2D port.

D2D 14-pin [1] Connect the 10-pin, 12-pin and 14-pin harnesses to 10-pin 12-pin (-) Unlock Output: Black/White DBALL2, then wait until the LED turns ON solid red. & (-) PTS Output: Green/Black 1 rd st 3 nd [1] (-) Lock Output: Green/White 1 2 Solid (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart Ensure that every key fob except one is located a minimum of 10 feet (3 meters) away from the vehicle BEFORE proceeding with the programming sequence.

This step is required for programming only. REMOVE REMOVE CR 2032 Remove the backup key from the transmitter. THE KEY BATTERY 3V 2 Open the key fob and remove the battery.

Go to the next page to complete the module programming.

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 20

Place and hold the key fob in front of PTS button. Place keyfob in front of 3 Hold the key fob in front of PTS button for steps 4 to 6. PTS button

4 Push the PTS button twice to turn ON ignition and wait for the key light to flash. Push x2

Brake Brake Press the brake pedal until the LED starts flashing pedal pedal 5 orange slowly then release the pedal. & & Press Flashes Release slowly

6 Push the PTS button once to turn the ignition OFF. Push x1

7 Disconnect the module and complete the Key2GO programming.

Web Programming (for Key2GO) Refer to the LED Diagnostics section for more information and for troubleshooting purposes. Version 4.5 or higher of XpressVIP must be installed on your computer to complete this programming sequence.

Remove the module from the vehicle and reconnect it to your computer. The web site will automatically 1 recognize that you are moving onto the second phase of the programming sequence.

2 Click on Submit Key2GO Request.

[1] (-) Unlock Output: Black/White Once the configuration is completed, reconnect the module. & (-) PTS Output: Green/Black 3 The LED turns ON solid green for 3 seconds, then turns off. [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black Solid x3 Secs Off See Vehicle Wiring Reference Chart 4 You can now reassemble the key fob.

You have successfully completed the module programming sequence.

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 21 Module Reset A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.

14-pin If required for your installation, connect the 10-pin & 12-pin D2D 12-pin harnesses to the module. Press and hold the programming 10-pin 1 4th button, then connect the 14-pin harness to the module. 1st 2nd 3rd

Wait 3 seconds until the LED turns ON solid orange then release the 2 programming button. The LED turns ON solid red. & & Solid Release Solid

Hard Reset Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.

Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds 2 until the LED starts to flash orange and red. & Solid Flashes

3 Release the programming button. The LED turns ON solid red. & Release Solid

[1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 22 Feature & Option List It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. Manual configuration of the features is possible using the information on this page.

*Default Option Feat. Operation Flashes / Option Description 1. No RF Output* Module is connected to a remote starter using a standard installation. 1 RFTD Output Type 2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available). 3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available). 1. Trunk* Will pop the trunk if available. 2 Trunk 2. Right Sliding Door When available, will operate the right sliding door. 3. Left Sliding Door When available, will operate the left sliding door. 1. Trunk Will pop the trunk if available. 3 Aux1 2. Right Sliding Door* When available, will operate the right sliding door. 3. Left Sliding Door When available, will operate the left sliding door. 1. Trunk Will pop the trunk if available. 4 Aux2 2. Right Sliding Door When available, will operate the right sliding door. 3. Left Sliding Door* When available, will operate the left sliding door. 1. Disabled The remote starter parking lights wire must be connected in the vehicle. 5 Parking Light Control On Data 2. Enabled* The parking lights will be controlled by CAN wires. 1. Disabled The vehicle is not equipped with an OEM alarm. This feature must be enabled when the vehicle is equipped with an OEM security alarm. 6 OEM Security Disarm On Data 2. Enabled* The alarm original to the vehicle is disarmed using the bypass and Push-to-Start (PTS) button. 1. Disabled The remote starter door lock wires must be connected in the vehicle. 2. Enabled - Type1 (EU) Works for most European vehicles. 7 Door Lock Control On Data Works for most North American vehicles. (We've noticed that some North American 3. Enabled - Type2 (US)* vehicles need to be set to "Type 1 (EU)" to work properly.)

[1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 23 Feature Programming Programming Button To enter feature programming routine - Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the Programming button. - The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.

Changing feature options - Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the DBALL in RSR using 3x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will change the option for the selected feature. - The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.

Accessing another feature - Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.

When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.

Once a feature is programmed - Other features can be programmed. - The feature programming can be exited.

Exiting feature programming - No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence. OR - Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.

[1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 24 LED Diagnostics & Troubleshooting

LED Description Troubleshooting Module Programming Make sure the D2D harness is connected or that the 12 Off Module has no power. Volt is present between the red and black wires. If the 12 Volt is present, the module may be defective. Ensure the correct programming procedure is being Solid red Waiting to begin the programming sequence. followed. Reset the module and complete the programming again. Initialization failed. Flashes red If the issue persists, please contact Technical Support. & green (If compatible) when RXT mode is not desired or Solid orange Transponder functions were skipped. convenience features are needed, please reset and reprogram the module. Flashes green All required CAN networks has been detected. Normal operation.

Flashes orange 1 of 2 CAN networks has been detected. Normal operation

Flashes Please follow the steps indicated in “Module orange Key2GO initiated. slowly programming” to complete the Key2GO programming.

Solid green x 3 secs Module was successfully programmed with all functions. Normal operation Module was successfully programmed without Solid orange Normal operation. x 3 secs transponder functions. Module Programming - Error Codes Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the Flashes red x 1 CAN2 not detected. ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. Check the J1850 wire connection. Wake up the data bus Flashes red J1850 not detected. x 1 by turning the ignition on and try again. Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try Flashes red x 2 CAN1 not detected. again. If your installation does not require this connection, skip this step by pressing the programming

button 5 times. [1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black Check the bypass line connection. If more than one wire [1] (-) Lock Output: Green/White Flashes red x 3 Bypass data not detected. is used, make sure they are not inverted. Ensure the (-) RAP Off Output: Red/Black vehicle still operates correctly using the factory key. See Vehicle Wiring Reference Chart The bypass calculation failed. Reset the module and try Flashes red x 4 Bypass processing error. again. If the condition persists, please contact Technical Support. The Yellow/Black wire did not detect the expected Flashes red x 5 ISO 1 not detected. signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. The Orange/Black wire did not detect the expected Flashes red x 6 ISO 2 not detected. signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. The Violet/Green or Violet/Brown wire did not detect the Flashes red expected voltage value. Refer to "Installation (wiring x 7 MUX not detected. diagrams & vehicle wiring reference charts)" to check the connections.

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 25 LED Diagnostics & Troubleshooting

LED Description Troubleshooting External module synchronization

The diagnostic data bus was not detected, therefore the (Flashes red, OBDII feature is not supported. red then SmartStart features will be limited. orange) x 10 Activation Ground When Running (Status)

Flashes green Ground When Running (Status) command received. The module has initialized the remote start sequence.

The module has received the Ignition ON command and Ignition ON command received. Flashes red is processing the remote start sequence. & orange Flashes The module has received the Start ON command and is green Start ON command received. quickly processing the remote start sequence. The PTS output from the module was not activated due Flashes red PTS shutdown error. x 10 to safety protection. Verify the CAN1 and CAN2 connections. Refer to Flashes red x 21 CAN bus incorrectly detected. “Installation (wiring diagrams & vehicle wiring reference charts)” to check the connections. Commands

Flashes orange x 1 LOCK command received.

Flashes orange x 2 UNLOCK command received.

Flashes TRUNK command received. orange x 3 If the bypass module fails to flash, it did not receive the

Flashes signal. Commands can come from RF or D2D. orange x 4 AUX1 command received.

Flashes orange x 5 AUX2 command received.

Flashes orange x 6 AUX3 command received. Shutdown codes

Flashes green x 1 Takeover successful. Normal operation.

Flashes red No UNLOCK command was received prior to opening the [1] (-) Unlock Output: Black/White x 1 Runsafe was not disabled. door, or the 45 second timer expired in takeover mode. (-) PTS Output: Green/Black The brakes were not detected, which prevents the [1] (-) Lock Output: Green/White Flashes red Brake was not detected. x 2 system from shutting down the vehicle. (-) RAP Off Output: Red/Black See The smart key was not detected, which prevents the Vehicle Wiring Reference Chart Flashes red Smart key was not detected. x 3 system from shutting down the vehicle. The vehicle was detected as moving, which prevents the Flashes red Speed was detected. x 4 system from shutting it down. RSR codes Activated from Web automatically when using RSR flash 3x OEM Lock Remote Start Activation was attempted Flashes red tool or can be done manually. Refer to feature x 7 when RFTD feature is disabled. programing section for more information. An RSR feature file mismatch was detected. Please Flashes red Feature error. x 9 contact Technical Support.

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 26 Parking Light Error Codes

The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below.

Flashes Diagnostic 1 Runtime expired. 2 Over-rev shutdown. 3 Low/No RPM. 4 Transmitter shutdown. 5 Brake shutdown. 6 Hood shutdown/Remote start safety override switch is ON*. 7 Remote start safety override switch is ON*. * If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.

[1] (-) Unlock Output: Black/White (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White (-) RAP Off Output: Red/Black See Vehicle Wiring Reference Chart

Firmware: NISS4HT Remote Start Ready (RSR) Installation Rev.: 20170221

Page 27 Limited One Year Consumer Warranty

For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.

This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com [1] (-) Unlock Output: Black/White 920-10012-01 2013-07 (-) PTS Output: Green/Black [1] (-) Lock Output: Green/White This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select (-) RAP Off Output: Red/Black See vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no Vehicle Wiring Reference Chart circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

Vehicle Takeover with Get In and Go* GG Pit Stop Mode The Pit Stop Mode feature is practical when you need to stop and run an errand, Close the vehicle doors, hood and trunk, then press Press but wish to keep the engine running. the Remote Start button on the transmitter to start remote start 1 button** the vehicle.** Stop the vehicle in a safe parking spot & P 1 and put the gear in Park (P). Press Unlock Press the Unlock button on the factory Stop & put vehicle in Park (P) button on OR 2 or aftermarket remote.** either remote** Press the button to remote start the vehicle.* Press Complete the following steps within 45 seconds The parking lights will flash once to indicate the remote start 2 button* or the vehicle will shut down. vehicle is now in Pit Stop Mode.

Enter the vehicle by opening and closing the driver It is now safe to leave the engine running and exit the 3 door, while making sure the key is inside with you. vehicle with the Smart Key in hand. Enter vehicle 3 Note: We recommend that you always lock the doors with key fob of your vehicle when leaving it unattended. Exit vehicle with Smart Key

* Your aftermarket remote may differ from the model shown in the illustrations. Depress the brake pedal, Ready to 4 put the car in gear and drive off. drive off Parking Light Error Codes * Get In and Go connections required. The parking lights on your vehicle will flash a specific number of times 3 seconds ** Your aftermarket remote may differ from the model shown in the illustrations. following an unscheduled shutdown or failure to start. Each flashing pattern is described below. Get In and Go Flashes Diagnostic 1 Runtime expired. Get In and Go is designed to provide users with easy takeover when GG entering their Push-to-Start (PTS) equipped vehicle, once it has been 2 Over-rev shutdown. remote started. 3 Low/No RPM. Typically, users would have to remote start their vehicle, then get inside and press 4 Transmitter shutdown. the vehicle start button to perform a takeover. There is therefore a physical action 5 Brake shutdown. required to drive away. With Get In and Go technology, you simply remote start the 6 Hood shutdown/Remote start safety override switch is ON*. vehicle, unlock the doors, get in and go... Nothing to do but put the gear in drive and 7 Remote start safety override switch is ON*. enjoy your vehicle. * If the vehicle hood status is supported through data, safety override switch input This unique feature monitors a variety of parameters such as the key fob, vehicle will report 7 flashes. speed sensor and door sensor, in order to perform takeover securily.

Remote Start Ready (RSR) List of Available Commands

Remote Start Ready (RSR) is a function that enables the interface Note that the information below is for Viper, Clifford and Python models. Icons and module to remote start the vehicle completely on its own. commands may differ depending on the remote brand and model purchased. Refer Consequently, there is no need for an aftermarket or an OEM remote to your authorized installation center for more information. starter in order to start the vehicle from a distance. Button(s) Actions

3x OEM Lock Remote Start Activation Press & hold for 1 second to lock. This solution includes the option to remote start your vehicle by pressing the Lock button 3 times consecutively. If your vehicle allows the OEM remote to remain Press & hold for 1 second to unlock. active while the engine is running, you may shut down your remote starter by pressing the Lock button 3 times once more. Press & hold for 1 second to remote start. Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it. Press & hold for 5 seconds to activate the trunk release (optional). Press once, then to activate the x1 + rear hatch/tail glass release (optional).* Press 3 times, then to activate x3 + the panic mode. Press once, then to reset the x1 + remote starter runtime.

* This output is configurable. see your authorized installation center for more information.

SmartStart Compatible Notes

This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.

What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system: Ÿ Lock/Arm Ÿ Unlock/Disarm Ÿ Remote Car Starter Ÿ Trunk Release Ÿ Panic Ÿ Aux Channels You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart! But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more. 3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet. For more information, visit www.mysmartstart.com.