DOCSLIB.ORG

Straight Vegetable Oil As a Vehicle Fuel? (Fact Sheet)

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Straight Vegetable Oil As a Vehicle Fuel? (Fact Sheet) VEHICLE TECHNOLOGIES OFFICE Straight Vegetable Oil as a Diesel Fuel? Biodiesel, a renewable fuel produced from animal fats or vegetable oils, is popular among many vehicle owners and fleet managers seek- ing to reduce emissions and support U.S. energy security. Questions sometimes arise about the viability of fueling vehicles with straight vegetable oil (SVO), or waste oils from cooking and other processes, without intermediate processing. But SVO and waste oils differ from biodiesel (and conventional diesel) in some important ways and are generally not considered acceptable vehicle fuels for large-scale or long-term use. Straight vegetable oil is not the same as biodiesel and is generally not Performance of SVO consistent across a substantial body of recommended for long-term vehicle use. Photo from iStock 8561648 Research has shown that there are sev- technical literature, including an SAE eral technical barriers to widespread technical paper that reviewed the pub- use of SVO as a vehicle fuel. lished data on the use of SVO in diesel engines.2 The SAE paper states: increasing proportions of vegetable oil The published engineering literature blended into the fuel.3 strongly indicates that the use of SVO Compared to No. 2 diesel fuel, all of the vegetable oils are much more Viscosity (the measure of a fuel’s leads to reduced engine life,1 caused by viscous, are much more reactive to the buildup of carbon deposits inside resistance to flow) is another impor- oxygen, and have higher cloud point the engine and the buildup of SVO in tant consideration related to the use and pour point temperatures. the engine lubricant. These issues are of SVO. The viscosity of SVO is much higher than that of diesel fuel at nor- attributable to SVO’s high viscosity Diesel engines with vegetable oils offer 1 and high boiling point relative to the acceptable engine performance and mal operating temperatures. Figure required boiling range for diesel fuel. emissions for short-term operation. 2 (on p. 2) illustrates the viscosities of The carbon buildup doesn’t neces- Long-term operation results in opera- diesel fuel and of 100% sunflower oil sarily happen immediately upon use tional and durability problems. over a range of temperatures. High of SVO; it typically takes place over fuel viscosity can cause premature the long term. These conclusions are Some investigators have explored wear of the fuel pumps and injectors. modifying vehicles to preheat SVO It can also dramatically alter the struc- prior to injection into the engine. Oth- ture of the fuel spray coming out of 1.8 ers have examined blends of vegetable the injectors: increasing droplet size, oil with conventional diesel. These decreasing spray angle, and increasing 1.6 techniques may mitigate the problems to some degree but don’t eliminate 1.4 them entirely. Studies show that car- 1 Sidibé, S.S.; Blin, J.; Vaitilingom, G.; Azoumah, Y. “Use of Crude Filtered Vegetable Oil as a Fuel in bon buildup (coking) continues over Diesel Engines State of the Art: Literature Review.” 1.2 time, resulting in higher engine main- Renew Sust Energ Rev 14(9):2748-2759 (2010). tenance costs and/or shorter engine 2 Babu, A.K.; Devaradjane, G. “Vegetable Oils 1.0 life. Figure 1 shows that the tendency and Their Derivatives as Fuels for CI Engines: An Overview.” SAE Technical Paper No. to form carbon deposits increases with 2003-01-0767. Coking Index Relative to Diesel to Relative Index Coking 0.8 3 0% 3% 5% 10% 15% 20% Figure 1 adapted from Jones, Samuel T.; Peterson, Charles L.; Thompson, Joseph C. Biological and Percent Oil in Fuel Agricultural Engineering Department, University of Idaho, Moscow, Idaho. “Used Vegetable Oil Fuel Blend Comparisons Using Injector Coking in a DI Figure 1. Buildup of carbon deposits Diesel Engine.” Presented at 2001 ASAE Annual in the engine as a function of the International Meeting, Sacramento, Calif., July 30– proportion of oil in the fuel. August 1, 2001. SAE Paper No. 01-6051. cleancities.energy.gov • January 2014 VEHICLE TECHNOLOGIES OFFICE • January 2014 • Page 2 100 than SVO and results in better engine 90 performance. In particular, biodiesel has a lower boiling point and viscosity 80 than SVO. 70 Biodiesel is most commonly used as a /second) 60 2 blend with petroleum diesel fuel. All 100% Sunflower Oil 50 manufacturers of diesel vehicles and engines have approved the use of B5 40 (a blend containing 5% biodiesel and 30 95% petroleum diesel), and some approve the use of blends up to B20 Viscosity (mm Viscosity 20 Diesel (20% biodiesel and 80% petroleum 10 diesel) or higher. 0 To ensure good performance in 18 28 38 48 58 68 78 88 engines, biodiesel must meet quality Temperature in °C specifications developed by ASTM International. ASTM Specification Figure 2. Viscosities of sunflower oil and conventional diesel fuel as a D6751 is for pure biodiesel (B100), function of temperature. used for blending with petroleum diesel fuel. Biodiesel that meets spray penetration. These effects tend to The long-term effect of using SVO in ASTM D6751 is legally registered increase wetting of the engine’s internal diesel engines equipped with modern with the U.S. Environmental Protec- surfaces, thereby diluting the engine emission control systems is also a mat- tion Agency. Blends up to B5 may lubricant and increasing the tendency ter of concern. Buildup of fuel in the be found in conventional diesel fuel for coking. lubricant is more significant in these without additional labeling at the engines—even for petroleum diesel— pump. Properties of these low-level and would likely be severe with SVO. blends are covered by the diesel fuel Where can I get more In general, these systems were not ASTM Specification D975. For blends originally designed to accommodate information? of biodiesel ranging from B6 to B20, the properties of SVO, and they can be a separate specification exists, ASTM ■ The U.S. Department of Energy’s seriously damaged or poisoned by out- D7467, and pump labeling is required Alternative Fuels Data Center, at of-spec or contaminated fuel. to inform the consumer that a bio- afdc.energy.gov, contains a vast diesel blend is being sold. collection of information on alter- native fuels and alternative fuel Biodiesel: Fuel Made For a complete list of ASTM biodiesel vehicles. From SVO requirements, see the Biodiesel Han- Biodiesel is an alternative fuel that can dling and Use Guidelines at www.nrel. ■ The National Biodiesel Board is the national trade association be made from SVO or other fats in a gov/vehiclesandfuels/pdfs/43672.pdf. In representing the biodiesel indus- chemical process called transesterifica- addition, the biodiesel industry has try. Its website, biodiesel.org, tion, which involves a reaction with instituted a quality assurance program serves as a clearinghouse of methanol, using caustic soda (sodium for biodiesel producers and market- biodiesel-related information. hydroxide) as a catalyst. Biodiesel ers. To learn more about the BQ-9000 has substantially different properties program, visit bq-9000.org. Clean Cities Technical Response Service 800-254-6735 • [email protected] DOE/GO-102014-3449 • January 2014 Prepared by the National Renewable Energy Laboratory (NREL), a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy; NREL is operated by the Alliance for Sustainable Energy, LLC. Printed with a renewable-source ink on paper containing at least 50% wastepaper, including 10% post consumer waste..
Load more

Recommended publications
  • Olive Oil Jars Left Behind By
    live oil jars left behind by the ancient Greeks are testament to our centuries- old use of cooking oil. Along with salt and pepper, oil Oremains one of the most important and versatile tools in your kitchen. It keeps food from sticking to pans, adds flavor and moisture, and conducts the heat that turns a humble stick of potato into a glorious french fry. Like butter and other fats, cooking oil also acts as a powerful solvent, unleashing fat-soluble nutrients and flavor compounds in everything from tomatoes and onions to spices and herbs. It’s why so many strike recipes begin with heating garlic in oil rather than, say, simmering it in water. The ancient Greeks didn’t tap many cooking oils. (Let’s see: olive oil, olive oil, or—ooh, this is exciting!—how about olive oil?) But you certainly can. From canola to safflower to grapeseed to walnut, each oil has its own unique flavor (or lack thereof), aroma, and optimal cooking temperature. Choosing the right kind for the task at hand can save you money, boost your health, and improve your cooking. OK, so you probably don’t stop to consider your cooking oil very often. But there’s a surprising amount to learn about What’s this? this liquid gold. BY VIRGINIAWILLIS Pumpkin seed oil suspended in corn oil—it looks like a homemade Lava Lamp! 84 allrecipes.com PHOTOS BY KATE SEARS WHERE TO store CANOLA OIL GRAPESEED OIL are more likely to exhibit the characteristic YOUR OIL flavor and aroma of their base nut or seed.
    [Show full text]
  • Evaluation of the Use of Recycled Vegetable Oil As a Collector Reagent in the Flotation of Copper Sulfide Minerals Using Seawater
    recycling Article Evaluation of the Use of Recycled Vegetable Oil as a Collector Reagent in the Flotation of Copper Sulfide Minerals Using Seawater Felipe Arcos and Lina Uribe * School of Mining Engineering, University of Talca, Talca 3460000, Chile; [email protected] * Correspondence: [email protected]; Tel.: +56-220-1798 Abstract: Considering sustainable mining, the use of seawater in mineral processing to replace conventional water is an attractive alternative, especially in cases where this resource is limited. However, the use of this aqueous medium generates a series of challenges; specifically, in the seawater flotation process, it is necessary to adapt traditional reagents to the aqueous medium or to propose new reagents that achieve better performance and are environmentally friendly. In this research, the technical feasibility of using recycled vegetable oil (RVO) as a collector of copper sulfide minerals in the flotation process using seawater was studied. The study considered the analysis of the metallurgical indexes when different concentrations of collector and foaming reagent were used, considering as collectors the RVO, potassium amyl xanthate (PAX) and mixtures of these, in addition to the methyl isobutyl carbinol (MIBC) as foaming agent. In addition, it was evidenced that the best metallurgical indexes were achieved using 40 g/t of RVO and 15 g/t of MIBC, which corresponded to an enrichment ratio of 6.29, a concentration ratio of 7.01, a copper recovery of 90.06% and a selectivity index with respect to pyrite of 4.03 and with respect to silica of 12.89. Finally, in relation to the study of the RVO and PAX collector mixtures, it was found that a mixture of 60 g/t of RVO and 40 g/t of PAX in the absence of foaming agent presented the best results in terms of copper recovery (98.66%) and the selectivity index with respect to pyrite (2.88) and silica (14.65), improving Citation: Arcos, F.; Uribe, L.
    [Show full text]
  • Fuel Properties Comparison
    Alternative Fuels Data Center Fuel Properties Comparison Compressed Liquefied Low Sulfur Gasoline/E10 Biodiesel Propane (LPG) Natural Gas Natural Gas Ethanol/E100 Methanol Hydrogen Electricity Diesel (CNG) (LNG) Chemical C4 to C12 and C8 to C25 Methyl esters of C3H8 (majority) CH4 (majority), CH4 same as CNG CH3CH2OH CH3OH H2 N/A Structure [1] Ethanol ≤ to C12 to C22 fatty acids and C4H10 C2H6 and inert with inert gasses 10% (minority) gases <0.5% (a) Fuel Material Crude Oil Crude Oil Fats and oils from A by-product of Underground Underground Corn, grains, or Natural gas, coal, Natural gas, Natural gas, coal, (feedstocks) sources such as petroleum reserves and reserves and agricultural waste or woody biomass methanol, and nuclear, wind, soybeans, waste refining or renewable renewable (cellulose) electrolysis of hydro, solar, and cooking oil, animal natural gas biogas biogas water small percentages fats, and rapeseed processing of geothermal and biomass Gasoline or 1 gal = 1.00 1 gal = 1.12 B100 1 gal = 0.74 GGE 1 lb. = 0.18 GGE 1 lb. = 0.19 GGE 1 gal = 0.67 GGE 1 gal = 0.50 GGE 1 lb. = 0.45 1 kWh = 0.030 Diesel Gallon GGE GGE 1 gal = 1.05 GGE 1 gal = 0.66 DGE 1 lb. = 0.16 DGE 1 lb. = 0.17 DGE 1 gal = 0.59 DGE 1 gal = 0.45 DGE GGE GGE Equivalent 1 gal = 0.88 1 gal = 1.00 1 gal = 0.93 DGE 1 lb. = 0.40 1 kWh = 0.027 (GGE or DGE) DGE DGE B20 DGE DGE 1 gal = 1.11 GGE 1 kg = 1 GGE 1 gal = 0.99 DGE 1 kg = 0.9 DGE Energy 1 gallon of 1 gallon of 1 gallon of B100 1 gallon of 5.66 lb., or 5.37 lb.
    [Show full text]
  • Greenhouse Gas Impact of Marginal Fossil Fuel Use
    Greenhouse gas impact of marginal fossil fuel use Greenhouse gas impact of marginal fossil fuel use By: Arno van den Bos, Carlo Hamelinck Date: 12 November 2014 Project number: BIENL14773 © Ecofys 2014 by order of the European Oilseed Alliance (EOA), the European Biodiesel Board (EBB) and the European Vegetable Oil and Proteinmeal Industry (FEDIOL) ECOFYS Netherlands B.V. | Kanaalweg 15G | 3526 KL Utrecht| T +31 (0)30 662-3300 | F +31 (0)30 662-3301 | E [email protected] | I www.ecofys.com Chamber of Commerce 30161191 Summary Biofuels represent a major option to reduce greenhouse gas emissions from the transportation sector. When assessing the benefits of biofuels, they are compared to the fossil fuels they replace. In the framework of the European Renewable Energy Directive and the Fuel Quality Directive, this is done by comparing the lifecycle greenhouse gas emissions of biofuels to a ‘fossil comparator’. This fossil comparator is based on the average greenhouse gas intensity of fossil fuels brought on the EU transportation market. Unconventional oils such as extra heavy oil and bitumen (tar sands), kerogen oil (oil shale), light tight oil (shale oil), deep sea oil and synthetic products such as gas-to-liquids and coal-to-liquids, typically have higher carbon footprints than conventional oil mainly because the effort required to extract, refine and/or synthesize them is much larger than for conventional oil. As the share of these unconventional oil-based fuels gradually rises in the total fuel supply over time, the greenhouse gas footprint of the average fuel consumption also rises. Even for conventional oil production fields, because larger existing fields get depleted, the extraction efforts increase while smaller fields are taken in operation.
    [Show full text]
  • Air Quality Impacts of Biodiesel in the United States
    WHITE PAPER MARCH 2021 AIR QUALITY IMPACTS OF BIODIESEL IN THE UNITED STATES Jane O’Malley, Stephanie Searle www.theicct.org [email protected] twitter @theicct BEIJING | BERLIN | SAN FRANCISCO | SÃO PAULO | WASHINGTON ACKNOWLEDGMENTS This study was generously funded by the David and Lucile Packard Foundation and the Norwegian Agency for Development Cooperation. International Council on Clean Transportation 1500 K Street NW, Suite 650, Washington, DC 20005 [email protected] | www.theicct.org | @TheICCT © 2021 International Council on Clean Transportation EXECUTIVE SUMMARY Since the passage of the Clean Air Act in 1970, the U.S. Environmental Protection Agency (EPA) has enacted standards to reduce vehicle exhaust emissions. These standards set emission limits for pollutants that contribute to poor air quality and associated health risks, including nitrous oxide (NOx), hydrocarbons (HC), carbon monoxide (CO), and particulate matter (PM). Although the majority of the on-road vehicle fleet in the United States is fueled by gasoline, diesel combustion makes up an overwhelming share of vehicle air pollution emissions. Air pollution emissions can be affected by blending biodiesel, composed of fatty acid methyl ester (FAME), into diesel fuel. Biodiesel increases the efficiency of fuel combustion due to its high oxygen content and high cetane number. Studies have found that biodiesel combustion results in lower emissions of PM, CO, and HC, likely for this reason. However, studies have consistently found that biodiesel blending increases NOx formation. Industry analysts, academic researchers, and government regulators have conducted extensive study on the emissions impacts of biodiesel blending over the last thirty years. The EPA concluded in a 2002 report that, on the whole, biodiesel combustion does not worsen air quality compared to conventional diesel and reaffirmed that conclusion in a 2020 proposal and subsequent rulemaking.
    [Show full text]
  • A Two-Point Vehicle Classification System
    178 TRANSPORTATION RESEARCH RECORD 1215 A Two-Point Vehicle Classification System BERNARD C. McCULLOUGH, JR., SrAMAK A. ARDEKANI, AND LI-REN HUANG The counting and classification of vehicles is an important part hours required, however, the cost of such a count was often of transportation engineering. In the past 20 years many auto­ high. To offset such costs, many techniques for the automatic mated systems have been developed to accomplish that labor­ counting, length determination, and classification of vehicles intensive task. Unfortunately, most of those systems are char­ have been developed within the past decade. One popular acterized by inaccurate detection systems and/or classification method, especially in Europe, is the Automatic Length Indi­ methods that result in many classification errors, thus limiting cation and Classification Equipment method, known as the accuracy of the system. This report describes the devel­ "ALICE," which was introduced by D. D. Nash in 1976 (1). opment of a new vehicle classification database and computer This report covers a simpler, more accurate system of vehicle program, originally designed for use in the Two-Point-Time­ counting and classification and details the development of the Ratio method of vehicle classification, which greatly improves classification software that will enable it to surpass previous the accuracy of automated classification systems. The program utilizes information provided by either vehicle detection sen­ systems in accuracy. sors or the program user to determine the velocity, number Although many articles on vehicle classification methods of axles, and axle spacings of a passing vehicle. It then matches have appeared in transportation journals within the past dec­ the axle numbers and spacings with one of thirty-one possible ade, most have dealt solely with new types, or applications, vehicle classifications and prints the vehicle class, speed, and of vehicle detection systems.
    [Show full text]
  • Saturated, Unsaturated, and Trans Fat
    Lifestyle Coach Facilitation Guide: Post-Core Fats - Saturated, Unsaturated, and Trans Fat Content Overview This session answers the question “what is fat?” It explores the different types of fat, and shows which fats are healthy (monounsaturated and polyunsaturated) and which fats are unhealthy (saturated and trans fat). Participants learn tips for choosing foods with healthy fats and avoiding foods with unhealthy fats. More information on cholesterol appears in Post-Core Session: Heart Health. Lifestyle Coach Preparation Checklist Materials Post-core handouts: What is Fat? Healthy Fats: Omega-3, Monounsaturated and Polyunsaturated Fats to Avoid: Saturated and Trans Fat Identifying Healthier Alternatives Tips for Choosing the Best Types of Fat “Food and Activity Trackers” “Lifestyle Coach’s Log” Balance scale Post-Core: Fats – Saturated, Unsaturated, and Trans Fat Key messages to reinforce A completely fat-free diet would not be healthy, yet it is important that fat be consumed in moderation. The main types of “healthy” fats are monounsaturated and polyunsaturated. The main types of “unhealthy” fats are saturated and trans fat. Saturated fats are primarily found in foods that come from animals, such as meat and dairy. Try to switch to lower-fat versions of these foods. In order to avoid trans fat, look on nutrition labels for ingredients such as “partially hydrogenated” oils or shortening. In addition, look for trans fat in the nutritional information in products like commercially baked cookies, crackers, and pies, and fried foods. After the session At the completion of this session, do the following: Use the “Notes and Homework Page” for notes and follow-up tasks.
    [Show full text]
  • Water-Based Lubricants: Development, Properties, and Performances
    lubricants Review Water-Based Lubricants: Development, Properties, and Performances Md Hafizur Rahman 1, Haley Warneke 1, Haley Webbert 1, Joaquin Rodriguez 1, Ethan Austin 1, Keli Tokunaga 1, Dipen Kumar Rajak 2 and Pradeep L. Menezes 1,* 1 Department of Mechanical Engineering, University of Nevada-Reno, Reno, NV 89557, USA; mdhafi[email protected] (M.H.R.); [email protected] (H.W.); [email protected] (H.W.); [email protected] (J.R.); [email protected] (E.A.); [email protected] (K.T.) 2 Department of Mechanical Engineering, Sandip Institute of Technology & Research Centre, Nashik 422213, India; [email protected] * Correspondence: [email protected] Abstract: Water-based lubricants (WBLs) have been at the forefront of recent research, due to the abundant availability of water at a low cost. However, in metallic tribo-systems, WBLs often exhibit poor performance compared to petroleum-based lubricants. Research and development indicate that nano-additives improve the lubrication performance of water. Some of these additives could be categorized as solid nanoparticles, ionic liquids, and bio-based oils. These additives improve the tribological properties and help to reduce friction, wear, and corrosion. This review explored different water-based lubricant additives and summarized their properties and performances. Viscosity, density, wettability, and solubility are discussed to determine the viability of using water-based nano-lubricants compared to petroleum-based lubricants for reducing friction and wear in machining. Water-based liquid lubricants also have environmental benefits over petroleum-based lubricants. Further research is needed to understand and optimize water-based lubrication for tribological systems completely.
    [Show full text]
  • Revisiting the Compcars Dataset for Hierarchical Car Classification
    sensors Article Revisiting the CompCars Dataset for Hierarchical Car Classification: New Annotations, Experiments, and Results Marco Buzzelli * and Luca Segantin Department of Informatics Systems and Communication, University of Milano-Bicocca, 20126 Milano, Italy; [email protected] * Correspondence: [email protected] Abstract: We address the task of classifying car images at multiple levels of detail, ranging from the top-level car type, down to the specific car make, model, and year. We analyze existing datasets for car classification, and identify the CompCars as an excellent starting point for our task. We show that convolutional neural networks achieve an accuracy above 90% on the finest-level classification task. This high performance, however, is scarcely representative of real-world situations, as it is evaluated on a biased training/test split. In this work, we revisit the CompCars dataset by first defining a new training/test split, which better represents real-world scenarios by setting a more realistic baseline at 61% accuracy on the new test set. We also propagate the existing (but limited) type-level annotation to the entire dataset, and we finally provide a car-tight bounding box for each image, automatically defined through an ad hoc car detector. To evaluate this revisited dataset, we design and implement three different approaches to car classification, two of which exploit the hierarchical nature of car annotations. Our experiments show that higher-level classification in terms of car type positively impacts classification at a finer grain, now reaching 70% accuracy. The achieved performance constitutes a baseline benchmark for future research, and our enriched set of annotations is made available for public download.
    [Show full text]
  • Modelling of Emissions and Energy Use from Biofuel Fuelled Vehicles at Urban Scale
    sustainability Article Modelling of Emissions and Energy Use from Biofuel Fuelled Vehicles at Urban Scale Daniela Dias, António Pais Antunes and Oxana Tchepel * CITTA, Department of Civil Engineering, University of Coimbra, Polo II, 3030-788 Coimbra, Portugal; [email protected] (D.D.); [email protected] (A.P.A.) * Correspondence: [email protected] Received: 29 March 2019; Accepted: 13 May 2019; Published: 22 May 2019 Abstract: Biofuels have been considered to be sustainable energy source and one of the major alternatives to petroleum-based road transport fuels due to a reduction of greenhouse gases emissions. However, their effects on urban air pollution are not straightforward. The main objective of this work is to estimate the emissions and energy use from bio-fuelled vehicles by using an integrated and flexible modelling approach at the urban scale in order to contribute to the understanding of introducing biofuels as an alternative transport fuel. For this purpose, the new Traffic Emission and Energy Consumption Model (QTraffic) was applied for complex urban road network when considering two biofuels demand scenarios with different blends of bioethanol and biodiesel in comparison to the reference situation over the city of Coimbra (Portugal). The results of this study indicate that the increase of biofuels blends would have a beneficial effect on particulate matter (PM ) emissions reduction for the entire road network ( 3.1% [ 3.8% to 2.1%] by kg). In contrast, 2.5 − − − an overall negative effect on nitrogen oxides (NOx) emissions at urban scale is expected, mainly due to the increase in bioethanol uptake. Moreover, the results indicate that, while there is no noticeable variation observed in energy use, fuel consumption is increased by over 2.4% due to the introduction of the selected biofuels blends.
    [Show full text]
  • Making Markets for Hydrogen Vehicles: Lessons from LPG
    Making Markets for Hydrogen Vehicles: Lessons from LPG Helen Hu and Richard Green Department of Economics and Institute for Energy Research and Policy University of Birmingham Birmingham B15 2TT United Kingdom Hu: [email protected] Green: [email protected] +44 121 415 8216 (corresponding author) Abstract The adoption of liquefied petroleum gas vehicles is strongly linked to the break-even distance at which they have the same costs as conventional cars, with very limited market penetration at break-even distances above 40,000 km. Hydrogen vehicles are predicted to have costs by 2030 that should give them a break-even distance of less than this critical level. It will be necessary to ensure that there are sufficient refuelling stations for hydrogen to be a convenient choice for drivers. While additional LPG stations have led to increases in vehicle numbers, and increases in vehicles have been followed by greater numbers of refuelling stations, these effects are too small to give self-sustaining growth. Supportive policies for both vehicles and refuelling stations will be required. 1. Introduction While hydrogen offers many advantages as an energy vector within a low-carbon energy system [1, 2, 3], developing markets for hydrogen vehicles is likely to be a challenge. Put bluntly, there is no point in buying a vehicle powered by hydrogen, unless there are sufficient convenient places to re-fuel it. Nor is there any point in providing a hydrogen refuelling station unless there are vehicles that will use the facility. What is the most effective way to get round this “chicken and egg” problem? Data from trials of hydrogen vehicles can provide information on driver behaviour and charging patterns, but extrapolating this to the development of a mass market may be difficult.
    [Show full text]
  • 14. Diesel Fuel Standard and Compliance Program
    California’s Diesel Fuel Program November 29, 2018 1 Oil & Gas and GHG Mitigation Branch California Air Resources Board (CARB) 2 California Diesel Fuel Requirements ´ASTM D975, Standard Specification for Diesel Fuel Oils (enforced by the California Department of Agriculture’s Division of Measurement Standards) ´The California Diesel Fuel Regulations ´13 CCR 2281, Sulfur Content of Diesel Fuel ´13 CCR 2282, Aromatic Hydrocarbon Content of Diesel Fuel ´13 CCR 2293, et seq., Commercialization of Alternative Diesel Fuel 3 ASTM D975 - 2018, Standard Specification for Diesel Fuel Oils, Grade No. 2-D, S15 ´Flash Point, minimum, 52 °C (126 °F) ´Kinematic Viscosity at 40 °C, 1.9 - 4.1 mm2/s ´Cetane Number, minimum, 40 ´Cetane Index, minimum, or Aromaticity, maximum, 40 or 35 percent by volume ´Lubricity, High-Frequency Reciprocating Rig (HFRR), at 60 °C, maximum, 520 microns ´Conductivity, minimum, 25 pS/m (10-12 ohm-1m-1) 4 13 CCR 2281, Sulfur Content of Diesel Fuel ´Sulfur content maximum of 15 ppmw (mg/kg) ´Applicable to every gallon of vehicular and non-vehicular diesel fuel sold or supplied in California ´Enforced at all points of storage and distribution in California, from production or importation to dispensing 13 CCR 2282, Aromatic Content of 5 Diesel Fuel ´Aromatic hydrocarbon (AHC) content maximum of 10 percent by volume, or ´Certified emission-equivalent formulation established by engine emission testing, or ´Designated equivalent limits: ´AHC content, maximum, 21.0 percent by weight ´Polycyclic aromatic hydrocarbon (PAH) content,
    [Show full text]