2. Conic tool is using slug catcher shape for as standard specification.

This specification is effective to anti slug comes up. 1. We use the best quality highspeed steel materials. (1)Material is (2)Slug is push and Conic uses carefully selected high speed steel for punch. cut at “A” Punch pressed to coming position. process to “B” 2. Even D2 steel(SKD-11) is different from standard. Die Die position. Slug a) Conic uses improved D2 steel for die. Frictional wear This material has twice of spring character and hardness is HSS higher than general D2 steel. (HRC 58 to 60) D2 Improved D2 steel (3)After slug is (4)Area of “B” Also more better anti- chipping and crack than standard D2 lower than position is smaller Punch steel. position “B” than “C” position Spring character This imp This improved D2 steel has good performance for wire EDM scrap is released Die therefore slug would Die because material does not have residual stress in the to the scrap box. not comes up to upper material. area. “ Price example (Japanese Yen)” b) Conic uses super sub-zero heat treatment process on D2 Additional Maker Standard price Total steel for standard punch. anti-slug comes up test : Material is put into –130cent degree just after heat Conic 5,000JPY 0JPY 5,000JPY Silicon steel plate 0.35mm thickness treatment. Company “A” 10,000JPY 3,000JPY 13,000JPY This process gives material structure fine and better for Punch material is D2 steel (SKD-11)

stability and hardness. (Hits) Normally sub-zero process is done only for precision 3. Minute Corner R on the punching side edges. equipment or gages. Conic put the minute corner R on the edge of 14,500 the punching side edges because this corner Put the minute corner R

7,000 is the weakest point of shaped tools. After on the edge of the put small R on the corner tool life is much punching side edges. longer and prevent the unusual wear of the “Super sub-zero process” “Standard” punch body. >>>Example of damage of the corner.

Punching life which height of is higher than general D2 steel. Conic makes a lot of special tools. Our sales result of special tools are proof of quality and customer satisfaction. Production of grand total (special shapes and tool) (Sets) 1. Back taper on side of the punch. 520,000 Conic keeps drawings of

special tools for 30 years,

This specification makes better performance for less touching 500,000 so that, it is easy to order Back taper on side

area on the side face of punch body and less sticking material repeatedly.

on the side face. 480,000

2012 2013 2014 2015 2016 2017 2018 (Year)

““JJaappaann TTeecchhnnoollooggyy””

Tooling life ( plate 2.0mm thickness)

Super Dry Punch(SDP) 80,000

CONIC Long Life Punch(CLP) 30,000

CONIC Hard Punch(CHP) 20,000

TiN Coating 20,000

HSS 15,000 Super Dry Punch (SDP) D2 10,000 (Hits) ◆Material surface quality change(it does not have peeling off such as PVD coating)

Name Color Average Note Good for hardness(HV)

SDP Mat Gray 2,800 No lub oil necessary Stainless… CLP Dark Gray 3,000 High hardness Coated material…

CHP Material 1,000 Smooth surface no sticking Aluminum,Color…

◆PVD coating (thickness 2 to 3 microns) ◆PVD coating (thickness 2 to 3 microns) Name Color Average Note Good for hardness(HV)

TiN Gold 2,000 General use Mild steel…

TiAlN Dark purple 2,500 Anti heating Coated material…

The Most Popular Tooling “PROTECH-3” “Thick turret tooling”

New Stylle for Easy Operatiion!

Anybody can maiintaiin thiis tooll safety, accuratelly and speedy!

Strong Points of Strong Points of Since 1976 Tool Sales Desk Conic Turret Punch Press Tools Conic Turret Punch Press Tools

CCOONNIICC CCoo..,, LLttdd..

10-5 Taiheidai, Shoo-cho, Katsuta-gun, Okayama, 709-4321, Japan TEL : +81-868-38-6154 FAX : +81-868-38-6331 E-mail : [email protected] URL : https://www.conic.co.jp/

Oct.2019