DUAL MEMORY STOPWATCH Record split & lap : USER INSTRUCTIONS - Press S3 to start, press S2 to record KEY CONFIGURATION CHRONOGRAPH MODE split until memory is full. (depens S2 S1 S3 on model) S1 : MODE -When the memory is full, the top roll will S2 : SPLIT/RESET shown “FULL” and cannot record split S3 : START/STOP time anymore, while the bottom row “over S4 : RECALL all times” will still running. - Press S3 again to stop.

S4 Top row : No. of split and Split times. DATA RECALL: Middle row : Lap times - When in Chronograph mode Bottom row : Overall times - Press S4 to recall split times and lap times, TIME MODE : - Measure and record lap times and split you can see the and time of record, - Time adjustment : Press S1 goto TIME times and overall time simultaneously. after 2sec. can see the data. (Memories depends on model). mode. - Press S2 to recall the fastest & slowest - - Press and hold S2 for 2 to enter 1/1000 second precision for first 9hr, lap time. 59min, 59sec, 999millisecond. adjust mode. You can see the digit is flash- - Press S3 to recall the average time ing and now can be adjust. amount in these laps. How to start/stop a session: - Press S2 scroll next variable. - Press S1 back to chronograph mode dur- - Sequence: >Month>Date>12/24 Press S3 to start/stop, press S3 again to ing in data recall mode. resume the . format>Hour>Minute>Second Notes: - Press S3 to adjust value. Hold the button - You can recall the data by press S4 even for fast scrolling. How to reset the record: the stopwatch is running. - Press the S1 to confirm and back to TIME - Press S2 to reset to record while the - In case the new session is not yet start, mode. session is stop. you can still recall the last session data. COUNT DOWN TIMER MODE EXERCISE TIMER MODE How to use the Exercise Timer This timer will count down for INT ACT > - Press S4 to check the timer detail before INT PEST > INT ACT > .... as well as no. start the session. of loops you preset. - Press S3 to start, press S3 again to stop/ resume the timer. - Press S4 to restart the timer when timer is stop. - When the Action time is finish and start Top row : No. of loop pass counting Rest time, a long “beep” sound Middle row : Preset count down time will alert. Bottom row : Counting time INT ACT (Interval action times) - Another “beep” sound will alert. when How to set the count down timer INT PEST (Interval rest times) these is 5 sec. before the Rest time finish. - Press and hold S2 for 2sec. to enter INT LOOPS (Interval loops) - After complete the preset no. of loop, INT TOTAL (Interval total times) three times “beep” sound will be alert and setting mode. back to Exercise Timer mode. - First the digit is flashing, press How to set the Exercise Timer - Press and hold S2 for 2 sec. to enter S3 to increase value, press S2 switch to PACER MODE till 1/1000secound digit. Repeat setting mode. - You can see the first digit is flashing, the about step until complete the setting. press S2 again to start adjust minute. Press S1 when finish and back to Count Press S3 increase the value, press S2 to down timer mode. confirm and go next value for setting. How to start count down timer - Setting sequence: Action time (min. & - Press S3 to start/stop, press S3 again to sec.)>Rest time (min. & sec.)>No. of loop resume the timer. - Press S1 to confirm and back to Exercise - Press S2 to reset to preset countdown timer mode. Top row : PACE MODE time when timer is stop. -Max. Action/Rest Time: 59min.59sec. Middle row : No. of count /pace -Max. Loop: 30 Bottom row : Pace frequency(times/minute) How to set the pace frequency ALARM MODE: BATTERY REPLACEMENT -Once you enter Pace mode, the bottom When the LCD display becomes dim, replace value is flashing, press S2 to scroll the with a new battery. value, 10, 20, 30, 40, 50, 60, 70, 80, 90, Battery type: CR2032 x 1pcs open close 100, 120, 150, 180, 210, 240, 270, 300, 330 (pace/minute) Battery Hatch - Press S3 to confirm and start. Top row : Alarm 1 / 2 - Press S3 to stop, press S3 again to Middle row : Alarm time CR2032Battery *O-ring resume the pacer. Bottom row : Alarm status - Press S2 to reset the counter when pacer -Press S3 to scroll Alarm1, Alarm2, Hourly is stop. Press S2 again to enter setting model. chime. Note: -Press S4 to switch on/off the alarm or - Pacer will stop automatically when leave We strongly recommend taking your stopwatch hourly chime function. to a local jeweler to have battry replaced to Pacer Mode Alarm adjustment: Press and hold S2 for avoid possibility of permanently damaging of TALLY COUNTER MODE the stopwatch. 2 second to enter adjust mode. You can see the hour digit is flashing and press WARNING : S3 to adjust value. Hold the button for · Keep batteries away from children. If swal- fast scrolling. Hold the button for fast lowed, contact a doctor or emergency person- scrolling. nel immediately. · Batteries contain chemical substances. They - Press S2 or S3 to increament count by 1. - Press S2 scroll next variable. Sequence: Hour>Minute should be disposed of properly according to - To reset the counter, press and hold S4 local regulations. for 2 sec. - Press the S1 to confirm.