INTEGRATED PLANNING / INSTALLATION GUIDE

Effective 3/20 | WCAG INTEGRATED COLUMN SKSCR2401P FLUSH INSTALLATION 24-INCHSKSCR2401P INTEGRATED COLUMN REFRIGERATOR24-INCH INTEGRATED COLUMN REFRIGERATOR 24-INCH INTEGRATED COLUMN REFRIGERATOR CUTOUT DIMENSIONS – FLUSH INSTALLATION CUTOUT DIMENSIONS – RETROFIT INSTALLATION CUTOUTSINGLE COLUMN DIMENSIONS – FLUSH INSTALLATION SINGLE COLUMN CUTOUT DIMENSIONS – FLUSH INSTALLATION CUTOUT DIMENSIONS – RETROFIT INSTALLATION SINGLESINGLE COLUMN COLUMN 24" (610 mm) SINGLE COLUMN 24" (610 mm) finished width finished width 24" (610 mm) Notes 24" (610 mm) finished width finished width Refrigerator can be installed flush with 3/4" custom panel

25" (635 mm) or optional stainless panel kit. 24" (610 mm) 4" 4" min. depth min. depth (102 mm) With a 25"(102 (635 mm) mm) cutout depth, the front face of the finished 25" (635 mm) 24" (610 mm) 4" finished4" min. depth refrigerator fits flush with 25" (635 mm) depthmin. adjacent depth (102return* mm) (102return* mm) finished cabinets.finished return* return* Electrical 84" A 115V, 60Hz., 15 amp power supply is required. An 84" (2134 mm) (2134 mm) 84" individual properly grounded branch circuit or circuit 84" (2134 mm) (2134 mm) 5" breaker is recommended.5" Install a properly grounded (127 mm) 3-prong electrical(127 receptacle mm) recessed into the back . electrical electrical location5" Electrical must belocation located5" on rear wall as shown. (127 mm) (127 mm) electrical electrical location Note: GFI (ground locationfault interrupter) is not recommended. 4" 4" (102 mm) Water Line (102 mm) water location water location 4" A cold water supply is required4" for water dispenser (102 mm) (102 mm) 1 3/8" (35water mm) location operation. Water1 3/8" pressure (35water mm) location must be between 20 and 120 p.s.i. 1 3/8" (35 mm) 1 3/8" (35 mm) *A minimum 4" (102 mm) finished return that matches the Tubing*A minimum should be4" (102 long mm) enough finished to return extend that matchesto the front the cabinet of the exterior is recommended on all sides and the top of the cutout exterior is recommended on all sides and the top of the cutout refrigerator. Allow enough tubing to accommodate a bend *opening.A minimum The 4" shaded (102 mm) area finished will be return visible that after matches installation. the cabinet *opening.A minimum The 4" shaded (102 mm) area finished will be return visible that after matches installation. the cabinet exterior is recommended on all sides and the top of the cutout leadingexterior into is the recommended water line onconnection. all sides and the top of the cutout opening. The shaded area will be visible after installation. Anopening. optional The Frame shaded Kit areacan bewill used be visible to provide after ainstallation. finished look to Waterunfinished line can cabinet enter returns.an opening through or back wall. An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.

24-INCH INTEGRATED COLUMN REFRIGERATOR INSTALLATION CLEARANCES – FLUSH INSTALLATION INSTALLATION CLEARANCES – FLUSH INSTALLATION TOP VIEW TOPINSTALLATION VIEW CLEARANCES – FLUSH INSTALLATION TOP VIEW 24" (610 mm) * handle must be Notes added to this dimension. 24" (610 mm) ** *VariesDoor handle depending must onbe the Door Swing Clearances – The installation must allow for 11 3/8"* thicknessadded to thisof the dimension. custom clearances to adjacent or cabinets. This refrigerator 25" (288 mm) cabinet panel. The door (635 mm) 1/8" 1/8" ** Varies depending on the is equipped with a 2-position door stop. The factory-set (3 mm) (3 mm) 11 3/8"* panelsthickness in theof the optional custom 25" min. min. (288 mm) Signature Suite 115° door swing can be adjusted to 90° if clearance to (635 mm) 1/8" 1/8" 1 1/4"* cabinet panel. The door (3 mm) (3 mm) (32 mm) stainlesspanels in steelthe optional door panel adjacent cabinets or walls is restricted. min. min. kitSignature are 3/4" Kitchen (19 mm) Suite thick. 23 3/4" 1 1/4"* (32 mm) Clearances – The Door Handle depth must (603 mm) stainless steel door panel 115° kit are 3/4" (19 mm) thick. be added to the dimension noted to determine the total 25 1/2" 23 3/4" (648 mm) (603 mm) clearances required from adjacent cabinets or walls. This 115° 25 1/2" clearance will vary depending on the custom handle used. (648 mm) 90° 3/4" (19 mm)** When using the Stainless Steel Door Panel Kit w/Handle or 90° 3/4" the Brushed Aluminum Handle (optional accessories), the (19 mm)** door handle clearance with door open 115° is 14" (356 mm).

Page 2 of 19 | Effective 3/20 | WCAG INTEGRATED COLUMN SKSCR3001P FLUSH INSTALLATION SKSCR3001P30-INCH INTEGRATED COLUMN 30-INCHREFRIGERATOR INTEGRATED COLUMN REFRIGERATOR 30-INCH INTEGRATED COLUMN REFRIGERATOR CUTOUT DIMENSIONS – FLUSH INSTALLATION CUTOUT DIMENSIONS – RETROFIT INSTALLATION CUTOUTSINGLE COLUMN DIMENSIONS – FLUSH INSTALLATION SINGLE COLUMN CUTOUT DIMENSIONS – FLUSH INSTALLATION CUTOUT DIMENSIONS – RETROFIT INSTALLATION SINGLE COLUMN COLUMN 30" (762 mm) SINGLE COLUMN 30" (762 mm) finished width finished width 30" (762 mm) Notes 30" (762 mm) finished width finished width Refrigerator can be installed flush with 3/4" custom panel

25" (635 mm) or optional stainless steel panel kit. 24" (610 mm) 4" 4" min. depth min. depth (102 mm) With a 25"(102 (635 mm) mm) cutout depth, the front face of the finished 25" (635 mm) finished 24" (610 mm) 4" refrigerator4" fits flush with 25" (635 mm) depth adjacent (102return* mm) min. depth (102return* mm) min. depth finished cabinets.finished return* return* Electrical 84" 84" (2134 mm) A 115V, 60Hz., 15 amp power supply is required. An (2134 mm) 84" individual properly grounded branch circuit or circuit 84" (2134 mm) (2134 mm) 5" breaker is recommended.5" Install a properly grounded (127 mm) 3-prong electrical (127receptacle mm) recessed into the back wall. electrical electrical location5" Electrical must be locatedlocation5" on rear wall as shown. (127 mm) (127 mm) electrical electrical location Note: GFI (ground faultlocation interrupter) is not recommended. 4" 4" (102 mm) Water Line (102 mm) water location water location 4" A cold water supply is required4" for water dispenser (102 mm) (102 mm) 1 3/8" (35water mm) location operation. Water1 3/8"pressure (35water mm) locationmust be between 20 and 120 p.s.i. 1 3/8" (35 mm) 1 3/8" (35 mm) *A minimum 4" (102 mm) finished return that matches the cabinet Tubing*A minimumshould be4" (102long mm) enough finished to return extend that matchesto the front the cabinet of the exterior is recommended on all sides and the top of the cutout exterior is recommended on all sides and the top of the cutout refrigerator. Allow enough tubing to accommodate a bend *opening.A minimum The 4" shaded (102 mm) area finished will be return visible that after matches installation. the cabinet *opening.A minimum The 4" shaded (102 mm) area finished will be return visible that after matches installation. the cabinet exterior is recommended on all sides and the top of the cutout leadingexterior into isthe recommended water line connection.on all sides and the top of the cutout opening. The shaded area will be visible after installation. opening.An optional The Frame shaded Kit areacan bewill used be visible to provide after ainstallation. finished look to Waterunfinished line can cabinetenter anreturns. opening through floor or back wall. An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.

30-INCH INTEGRATED COLUMN REFRIGERATOR INSTALLATION CLEARANCES – FLUSH INSTALLATION INSTALLATION CLEARANCES – FLUSH INSTALLATION TOP VIEW TOPINSTALLATION VIEW CLEARANCES – FLUSH INSTALLATION

TOP VIEW 30" (762 mm) *Door handle must be Notes added to this dimension. 30" (762 mm) ** *VariesDoor handle depending must onbe the Door Swing Clearances – The installation must allow for 13 7/8"* thicknessadded to thisof the dimension. custom clearances to adjacent walls or cabinets. This refrigerator 25" (352 mm) cabinet panel. The door (635 mm) 1/8" 1/8" ** Varies depending on the is equipped with a 2-position door stop. The factory-set (3 mm) (3 mm) 13 7/8"* thicknesspanels in theof the optional custom min. min. 25" (352 mm) cabinetSignature panel. Kitchen The Suite door 115° door swing can be adjusted to 90° if clearance to (635 mm) 1/8" 1/8" 1 1/4"* (3 mm) (3 mm) (32 mm) panelsstainless in steelthe optional door panel adjacent cabinets or walls is restricted. min. min. Signaturekit are 3/4" Kitchen (19 mm) Suite thick. 29 3/4" 1 1/4"* (756 mm) (32 mm) stainless steel door panel Door Handle Clearances – The Door Handle depth must 115° kit are 3/4" (19 mm) thick. be added to the dimension noted to determine the total 31 1/2" 29 3/4" (800 mm) (756 mm) clearances required from adjacent cabinets or walls. This 115° 31 1/2" 3/4" clearance will vary depending on the custom handle used. (800 mm) 90° (19 mm)** When using the Stainless Steel Door Panel Kit w/Handle or 90° 3/4" the Brushed Aluminum Handle (optional accessories), the (19 mm)** door handle clearance with door open 115° is 16" (406 mm).

Page 3 of 19 | Effective 3/20 | WCAG INTEGRATED COLUMN FLUSH INSTALLATION SKSCF1801P 18" INTEGRATED COLUMN FREEZER 18-INCH INTEGRATED COLUMN FREEZER CUTOUT DIMENSIONS – FLUSH INSTALLATION CUTOUT DIMENSIONS – FLUSH INSTALLATION CUTOUT DIMENSIONS – RETROFIT INSTALLATION SINGLE COLUMN COLUMN SINGLE COLUMN

18" (457(457 mm)mm) Notes 17 3/4" (451(451 mm)mm) finished width finished width finished width Freezer can be installed flush orfinished proud widthwith 3/4" custom panel or optional stainless steel panel kit.

25" (635 mm) With a 25" (635 mm) cutout depth, the front face24" (610 of mm) 4" 25" (635 mm) 4" 24" (610 mm) 4" min. depth the freezer4" fits flush with 25" (635 mm) depthmin. adjacent depth (102(102 mm)mm) (102(102 mm)mm) finishedfinished cabinets.finishedfinished return*return* return*return* Electrical A 115V, 60Hz., 15 amp power supply is required. An individual properly grounded branch circuit or circuit 84" 84" (2134(2134 mm)mm) breaker is recommended. Install a properly grounded(2134(2134 mm)mm) 3-prong electrical receptacle recessed into the back wall. 5" 5" (127 mm) Electrical must be(127 located mm) on rear wall as shown. (127 mm) (127 mm) electrical electrical locationlocation Note: GFI (ground locationlocationfault interrupter) is not recommended. Water Line

4" 4" (102 mm) A cold water supply is required(102 mm) for automatic icemaker (102 mm) (102 mm) water location operation. Water pressurewater location must be between 20 and 120 p.s.i. (35 mm) (35 mm) 1 3/8" (35 mm) 1 3/8" (35 mm) Tubing should be long enough to extend to the front of the freezer. Allow enough tubing to accommodate a bend *A minimum 4" (102(102 mm)mm) finishedfinished returnreturn thatthat matchesmatches thethe cabinetcabinet *A minimum 4" (102(102 mm)mm) finishedfinished returnreturn thatthat matchesmatches thethe cabinetcabinet exterior is recommended on all sides and the top of the cutout leadingexterior into is the recommended water line onconnection. all sides and the top of the cutout opening. The shaded area will be visible after installation. opening. The shaded area will be visible after installation. Water line can enter an opening through floor or back wall. An optional Frame Kit can be used to provide a finished look to InstallAn a optionalshut-off Frame valve Kit canbetween be used the to icemakerprovide a finished water lookvalve to unfinished cabinet returns. and cold water supply in the .

18-INCH INTEGRATED COLUMN FREEZER

INSTALLATIONINSTALLATION CLEARANCESCLEARANCES CLEARANCES –– FLUSHFLUSH – FLUSH INSTALLATIONINSTALLATION INSTALLATION INSTALLATIONINSTALLATION CLEARANCESCLEARANCES –– RETROFITRETROFIT INSTALLATIONINSTALLATION TOPTOP VIEW VIEW TOP VIEW 17 3/4" 18" (457 mm) 18" (457 mm) (451(451 mm)mm) **Door handle must be Notes **Door handle must be added to this dimension. added to this dimension. ** Varies depending on the Door Swing Clearances – The installation must allow for ** Varies depending on the 8 3/4"* 25" ** Varies depending on the 8 3/4"* 24" ** Varies depending on the 8 3/4"* 25" thickness of the custom 8 3/4"* 24" thickness of the custom (223 mm) 1/4" 1/4" (635 mm) thickness of the custom clearances(223 mm) to adjacent walls or(610 cabinets. mm) This freezer is thickness of the custom (223 mm) 1/4" 1/4" (635 mm) cabinet panel. The door (223 mm) 1/8" 1/8" (610 mm) cabinet panel. The door (6(6 mm)mm) (6(6 mm)mm) cabinet panel. The door equipped with a 1/8"2-position1/8" door stop. The factory-set 115° cabinet panel. The door min. min. panels in the optional (3(3 mm)mm) (3(3 mm)mm) panels in the optional min. min. panels in the optional min. min. panels in the optional 1 1/4"* Signature Kitchen Suite door swing can bemin adjusted. min. to 90° if clearance to adjacent Signature Kitchen Suite (321 1/4"* mm) Signature Kitchen Suite Signature Kitchen Suite (32 mm) stainless steel doorr panelpanel cabinets or walls is restricted. stainless steel doorr panelpanel kit are 3/4" (19 mm) thick. kit are 3/4" (19 mm) thick. 17 3/4" kit are 3/4" (19 mm) thick. 17 3/4" kit are 3/4" (19 mm) thick. (451(451 mm)mm) Door Handle Clearances(451(451 mm)mm) – The Door Handle depth must 115° 115° Optional Frame Kit 19 1/2" be added to the dimension noted20 1/4" to determineOptional Framethe total Kit 19 1/2" 20 1/4" SKSFK800CS can (495(495 mm)mm) clearances required from adjacent(514(514 mm)mm) cabinetsSKSFK800CS or walls. can This be installed for a 90° 3/4" clearance90° will vary depending on the customfinished handle look. used. 3/4" 90° (193/4" mm)** 90° finished look. (193/4" mm)** (19 mm)** When using the Stainless Steel Door Panel Kit w/Handle or (19 mm)** the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 11" (279 mm). Page 4 of 19 | Effective 3/20 | WCAG

INSTALLATIONINSTALLATION CLEARANCESCLEARANCES –– FLUSHFLUSH INSTALLATIONINSTALLATION WITHWITH TRIMTRIM PIECEPIECE

TOP VIEW

18" (457(457 mm)mm) **Door handle must be added to this dimension. ** Varies depending on the 8 3/4"* 25" (223 mm) thickness of the custom (223 mm) (635(635 mm)mm) thickness of the custom 1/8" 1/8" cabinet panel. The door (3 mm) (3 mm) (3 mm) (3 mm) panels in the optional min.. min.. Signature Kitchen Suite stainless steel doorr panelpanel kit are 3/4" (19 mm) thick. 17 3/4" kit are 3/4" (19 mm) thick. (451(451 mm)mm) 115° 19 1/2" (495(495 mm)mm)

90° 3/4" (19(19 mm)**mm)** INTEGRATED COLUMN FLUSH INSTALLATION SKSCF2401P 24" INTEGRATED COLUMN FREEZER 24-INCH INTEGRATED COLUMN FREEZER CUTOUT DIMENSIONS – FLUSH INSTALLATION CUTOUT DIMENSIONS – FLUSH INSTALLATION SINGLESINGLE COLUMN COLUMN

24" (610 mm) Notes 24" (610 mm) finished width finished width Freezer can be installed flush with 3/4" custom panel or optional stainless steel panel kit. With a 25" (635 mm) cutout depth, the front face of 25" (635 mm) 4" 25" (635 mm) 4" min. depth the freezer fits flush with 25" (635 mm) depth adjacent (102 mm) min. depth (102 mm) cabinets. finishedfinished return* return* Electrical A 115V, 60Hz., 15 amp power supply is required. An individual properly grounded branch circuit or circuit 84"84" (2134 mm) breaker is recommended. Install a properly grounded (2134 mm) 3-prong electrical receptacle recessed into the back wall. 5" (1275" mm) Electrical must be located on rear wall as shown. (127 mm) electrical electrical location Note: GFI (ground fault interrupter) is not recommended. location Water Line

4" (1024" mm) A cold water supply is required for automatic icemaker (102 mm) water location water location operation. Water pressure must be between 20 and 120 p.s.i. (35 mm) 11 3/8"3/8" (35 mm) Tubing should be long enough to extend to the front of the freezer. Allow enough tubing to accommodate a bend *A minimum 4" (102 mm) finished return that matches the cabinet *A minimum 4" (102 mm) finished return that matches the cabinet exteriorexterior isis recommendedrecommended onon allall sidessides andand thethe toptop ofof thethe cutoutcutout leading into the water line connection. opening. The shaded area will be visible after installation. opening. The shaded area will be visible after installation. Water line can enter an opening through floor or back wall. Install a shut-off valve between the icemaker water valve and cold water supply in the home.

INSTALLATIONINSTALLATION CLEARANCESCLEARANCES CLEARANCES –– FLUSHFLUSH – FLUSH INSTALLATIONINSTALLATION INSTALLATION TOP VIEW TOPTOP VIEWVIEW 24" (610 mm) 24" (610 mm) Door handle must be **Door handle must be Notes addedadded toto thisthis dimension.dimension. ** Varies depending on the Door Swing Clearances – The installation must allow for 11 3/8"* 25" ** Varies depending on the 11 3/8"* 25" thickness of the custom (288 mm) (635 mm) thickness of the custom clearances to adjacent walls or cabinets. This freezer is (288 mm) 1/8"1/8" 1/8"1/8" (635 mm) (3 mm) (3 mm) cabinetcabinet panel.panel. TheThe doordoor equipped with a 2-position door stop. The factory-set 115° (3 mm) (3 mm) panels in the optional minn.. minn.. panels in the optional 1 1/4"* Signature Kitchen Suite door swing can be adjusted to 90° if clearance to adjacent (321 1/4"*mm) Signature Kitchen Suite (32 mm) stainlessstainless steelsteel doodoorr panelpanel cabinets or walls is restricted. kit are 3/4" (19 mm) thick. 2323 3/4"3/4" kit are 3/4" (19 mm) thick. (603 mm) Door Handle Clearances – The Door Handle depth must (603 mm) 25 1/2" 1115°15° 25 1/2" (648 mm) be added to the dimension noted to determine the total (648 mm) clearances required from adjacent cabinets or walls. This 90° 3/4" clearance will vary depending on the custom handle used. 90° (19 3/4"mm)** (19 mm)** When using the Stainless Steel Door Panel Kit w/Handle or the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 14" (356 mm). Page 5 of 19 | Effective 3/20 | WCAG INTEGRATED COLUMN FLUSHSKSCF3001P INSTALLATION SKSCF3001P 30-INCH INTEGRATED 30-INCH INTEGRATED COLUMN FREEZER COLUMN FREEZER 30-INCH INTEGRATED COLUMN FREEZER

CUTOUT DIMENSIONS DIMENSIONS – FLUSH – FLUSH INSTALLATION INSTALLATION CUTOUTSINGLE COLUMN DIMENSIONS – FLUSH INSTALLATION SINGLE COLUMN COLUMN 30" (762 mm) finished30" (762 widthmm) Notes finished width Freezer can be installed flush with 3/4" custom panel or optional stainless steel panel kit.

25" (635 mm) 4" With a 25" (635 mm) cutout depth, the front face of 25" (635 mm) (1024" mm) min. depth min. depth the freezer fits flush with 25" (635 mm) depth adjacent (102finished mm) finishedreturn* cabinets. return* Electrical A 115V, 60Hz., 15 amp power supply is required. An 84" individual properly grounded branch circuit or circuit (213484" mm) (2134 mm) breaker is recommended. Install a properly grounded 5" 3-prong electrical receptacle recessed into the back wall. (1275" mm) Electrical must be located on rear wall as shown. electrical(127 mm) electricallocation location Note: GFI (ground fault interrupter) is not recommended. Water Line 4" (1024" mm) A cold water supply is required for automatic icemaker water(102 location mm) water location operation. Water pressure must be between 20 and 1 3/8" (35 mm) 120 p.s.i. 1 3/8" (35 mm) Tubing should be long enough to extend to the front of *A minimum 4" (102 mm) finished return that matches the cabinet the freezer. Allow enough tubing to accommodate a bend *exteriorA minimum is recommended 4" (102 mm) finished on all sidesreturn and that the matches top of thethe cutoutcabinet exterioropening. is The recommended shaded area on will all be sides visible and after the topinstallation. of the cutout leading into the water line connection. opening. The shaded area will be visible after installation. Water line can enter an opening through floor or back wall. Install a shut-off valve between the icemaker water valve and cold water supply in the home.

INSTALLATION CLEARANCES – FLUSH INSTALLATION INSTALLATIONINSTALLATION CLEARANCES CLEARANCES – FLUSH – FLUSH INSTALLATION INSTALLATION TOP VIEW TOPTOP VIEWVIEW 30" (762 mm) *Door handle must be Notes 30" (762 mm) *addedDoor handle to this must dimension. be added to this dimension. ** Varies depending on the Door Swing Clearances – The installation must allow for 13 7/8"* ** thicknessVaries depending of the custom on the clearances to adjacent walls or cabinets. This freezer is 25" 1/8" 1/8" (35213 7/8"* mm) cabinetthickness panel. of the The custom door (635 mm) 25" (31/8" mm) (31/8" mm) (352 mm) cabinet panel. The door equipped with a 2-position door stop. The factory-set 115° (635 mm) panels in the optional (3mi mm)n. (3mi mm)n. panels in the optional door swing can be adjusted to 90° if clearance to adjacent min. min. 1 1/4"* Signature Kitchen Suite (321 1/4"* mm) stainlessSignature steel Kitchen doo Suiter panel cabinets or walls is restricted. (32 mm) kitstainless are 3/4" steel (19 doomm)r panelthick. 29 3/4" kit are 3/4" (19 mm) thick. Door Handle Clearances – The Door Handle depth must (75629 3/4"mm) (756 mm) 115° be added to the dimension noted to determine the total 31 1/2" 115° (80031 1/2"mm) clearances required from adjacent cabinets or walls. This (800 mm) clearance will vary depending on the custom handle used. 90° 3/4" 90° (193/4" mm)** When using the Stainless Steel Door Panel Kit w/Handle or (19 mm)** the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 16" (406 mm). Page 6 of 19 | Effective 3/20 | WCAG INTEGRATED COLUMN FLUSHSKSCW181RP INSTALLATION SKSCW181RP18" INTEGRATED COLUMN 18"WINE INTEGRATED REFRIGERATOR COLUMN WITHOUT TRIM PIECE WINE REFRIGERATOR WITHOUT TRIM PIECE 18-INCH INTEGRATED COLUMN WINE REFRIGERATOR CUTOUTCUTOUT DIMENSIONS – FLUSH – FLUSH INSTALLATION INSTALLATION CUTOUTSINGLE DIMENSIONS COLUMN – FLUSH INSTALLATION SINGLE COLUMN COLUMN 18" (457 mm) 18"finished (457 mm) width Notes finished width Wine refrigerator can be installed flush with 3/4" custom panel or optional stainless steel panel kit. 25" (635 mm) 4" With a 25" (635 mm) cutout depth, the front face of 25"min. (635 depth mm) (1024" mm) (102finished mm) min. depth the wine refrigerator fits flush with 25" (635 mm) depth finishedreturn* adjacent cabinets. return* Electrical A 115V, 60Hz., 15 amp power supply is required. An 84" individual properly grounded branch circuit or circuit (213484" mm) (2134 mm) breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. 5" (1275" mm) Electrical must be located on rear wall as shown. (127electrical mm) electricallocation Note: GFI (ground fault interrupter) is not recommended. location

1 3/8" (35 mm) 1 3/8" (35 mm)

*A minimum 4" (102 mm) finished return that matches the cabinet *A exteriorminimum is 4"recommended (102 mm) finished on all return sides that and matches the top of the the cabinet cutout exterioropening. is recommended The shaded area on allwill sides be visible and the after top installation. of the cutout opening. The shaded area will be visible after installation.

18-INCH INTEGRATED COLUMN WINE REFRIGERATOR

INSTALLATIONINSTALLATION CLEARANCES CLEARANCES – FLUSH – FLUSH INSTALLATION INSTALLATION INSTALLATION CLEARANCES – FLUSH INSTALLATION TOPTOP VIEW VIEW TOP VIEW 18" (457 mm) *Door handle must be Notes 18" (457 mm) *Dooradded handle to this must dimension. be Door Swing Clearances – The installation must allow **addedVaries to dependingthis dimension. on the 25" 8 3/4"* ** Variesthickness depending of the oncustom the for clearances to adjacent walls or cabinets. This wine (63525" mm) 1/4" 1/4" 8(223 3/4"* mm) (635 mm) (6 mm) (6 mm) (223 mm) thicknesscabinet panel.of the customThe door refrigerator is equipped with a 2-position door stop. The 1/4" 1/4" cabinetpanels panel. in the The optional door (6 mm)min. (6 mm)min. factory-set 115° door swing can be adjusted to 90° if min. min. 1 1/4"* panelsSignature in the Kitchen optional Suite (32 mm) 1 1/4"* Signaturestainless Kitchen steel doo Suiter panel clearance to adjacent cabinets or walls is restricted. (32 mm) stainlesskit are 3/4" steel (19 doo mm)r panel thick. 17 3/4" Door Handle Clearances – The Door Handle depth must 17(451 3/4" mm) kit are 3/4" (19 mm) thick. (451 mm) 115° be added to the dimension noted to determine the total 19 1/2" 115° 19(495 1/2" mm) clearances required from adjacent cabinets or walls. This (495 mm) 90° 3/4" clearance will vary depending on the custom handle used. 90° (193/4" mm)** When using the Stainless Steel Door Panel Kit w/Handle or (19 mm)** the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 11" (279 mm).

Page 7 of 19 | Effective 3/20 | WCAG INTEGRATED COLUMN FLUSHSKSCW241RP INSTALLATION SKSCW241RP24-INCH INTEGRATED COLUMN 24-INCHWINE REFRIGERATOR INTEGRATED COLUMN WINE REFRIGERATOR 24-INCH INTEGRATED COLUMN WINE REFRIGERATOR CUTOUT DIMENSIONS – FLUSH INSTALLATION CUTOUTSINGLE COLUMN DIMENSIONS – FLUSH INSTALLATION CUTOUT DIMENSIONS – FLUSH INSTALLATION SINGLE COLUMN COLUMN 24" (610 mm) finished width 24" (610 mm) Notes finished width Wine refrigerator can be installed flush with 3/4" custom panel or optional stainless steel panel kit. 25" (635 mm) 4" (102 mm) min. depth With a 25" (635 mm) cutout depth, the front face of 25" (635 mm) finished4" min. depth the wine refrigerator fits flush with 25" (635 mm) depth (102return* mm) finished adjacent cabinets. return* Electrical

84" A 115V, 60Hz., 15 amp power supply is required. An (2134 mm) individual properly grounded branch circuit or circuit 84" (2134 mm) breaker is recommended. Install a properly grounded 5" 3-prong electrical receptacle recessed into the back wall. (127 mm) electrical5" Electrical must be located on rear wall as shown. (127location mm) electrical Note: GFI (ground fault interrupter) is not recommended. location

1 3/8" (35 mm)

1 3/8" (35 mm) *A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout *Aopening. minimum The 4" shaded(102 mm) area finished will be return visible that after matches installation. the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.

24-INCH INTEGRATED COLUMN WINE REFRIGERATOR

INSTALLATIONINSTALLATION CLEARANCES CLEARANCES – FLUSH – FLUSH INSTALLATION INSTALLATION INSTALLATIONTOP VIEW CLEARANCES – FLUSH INSTALLATION TOP VIEW TOP VIEW 24" (610 mm) *Door handle must be Notes added to this dimension. 24" (610 mm) *Door handle must be Door Swing Clearances – The installation must allow ** Varies depending on the added to this dimension. 25" 11 3/8"* thickness of the custom for clearances to adjacent walls or cabinets. This wine (635 mm) 1/8" 1/8" (288 mm) ** Variescabinet depending panel. The on door the refrigerator is equipped with a 2-position door stop. The 25" (3 mm) (3 mm) 11 3/8"* thicknesspanels in theof the optional custom (635 mm) min. min. (288 mm) cabinet panel. The door factory-set 115° door swing can be adjusted to 90° if 1/8" 1/8" 1 1/4"* Signature Kitchen Suite (3 mm) (3 mm) (32 mm) panels in the optional min. min. stainless steel door panel clearance to adjacent cabinets or walls is restricted. 1 1/4"* Signaturekit are 3/4" Kitchen (19 mm) Suite thick. 23 3/4" (32 mm) stainless steel door panel Door Handle Clearances – The Door Handle depth must (603 mm) kit are 3/4" (19 mm) thick. 23 3/4" 115° be added to the dimension noted to determine the total 25 1/2" (603 mm) (648 mm) 115° clearances required from adjacent cabinets or walls. This 25 1/2" clearance will vary depending on the custom handle used. (648 mm) 90° 3/4" (19 mm)** When using the Stainless Steel Door Panel Kit w/Handle 90° 3/4" (19 mm)** or the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 14" (356 mm). Page 8 of 19 | Effective 3/20 | WCAG INTEGRATED COLUMN FLUSH INSTALLATION

TOP VIEW DOOR SWING RANGE DIMENSIONS DOOR SWING DIMENSIONS Notes 3/4" (19 MM) 4" (102 mm) The installation must allow for proper4" (102 mm) FLUSH DOOR clearances to adjacent appliances, 3" (76 mm) 3" (76 mm) PANEL walls or cabinets. There should be no 2" (51 mm) interference when are opened. 2" (51 mm)

1" (25 mm) The space needed for the hinge and 1" (25 mm) the distance to the adjacent cabinetry and its handle is shown with both 3/4" Adjacent Cabinet/Appliance Closed Door Panel 3/4" Adjacent Cabinet/Appliance Closed Door Panel (19 mm) (19 mm) and 1 1/2" (38 mm) thick door 1 1/2" (38 mm) Adjacent Handle panels. Adjacent Cabinet/Appliance with Custom Door Panel Closed Custom Door Panel (Handle size and position must Adjacent Handle 1" (25 mm) be considered to avoid interference) If interference is an issue, the following solutions can be considered: (Handle size and position must 1" (25 mm) be considered to avoid interference) 2" (51 mm) • Limit the door swing angle to 90° with 2" (51 mm) 3" (76 mm) a door stop pin inserted into the hinge.

• Install a spacer between3" (76 mm) the appliance 4" (102 mm) and the opposing element that 4" (102 mm) Hinge at 115° Opening creates the interference. Hinge at 90° Opening TOP VIEW • If the door panel thickness is larger

DOOR SWING RANGE DIMENSIONS Hinge at 115° Opening

than 3/4" (19mm), consider reducing it. Hinge at 90° Opening

4" (102 mm) 4" (102 mm) 1 1/2" (38 MM) • Rearrange surrounding cabinetry or appliances to eliminate the 3" (76 mm) FLUSH DOOR 3" (76 mm) PANEL interference. 2" (51 mm) 2" (51 mm) • Create a protruding cutout for the appliance (see page 6 for “retrofit” 1" (25 mm) 1" (25 mm) installation).

Adjacent Cabinet/Appliance Closed Door Panel 3/4" Adjacent Cabinet/Appliance Closed Door Panel (19 mm) 1 1/2" (38 mm) Adjacent Handle Adjacent Cabinet/Appliance with Custom Door Panel Closed Custom Door Panel (Handle size and position must Adjacent Handle 1" (25 mm) be considered to avoid interference) (Handle size and position must 1" (25 mm) be considered to avoid interference) 2" (51 mm)

2" (51 mm) 3" (76 mm)

3" (76 mm) 4" (102 mm)

4" (102 mm) Hinge at 115° Opening Hinge at 90° Opening

Hinge at 115° Opening Hinge at 90° Opening

Page 9 of 19 | Effective 3/20 | WCAG INTEGRATED COLUMN FLUSH INSTALLATION

INSTALLATION PLANNING - MULTIPLE Integrated columns can be combined in cutout widths of 42", 48", 54" and 60". - The SKSFJ800P Joining Kit is required between units (kit included with all freezer columns.) - Reference the cutout dimensions for each column for detailed dimensions. - A minimum 15 amp (115V, 60Hz) power supply is required for each individual column. - A cold water supply is required for water dispenser and automatic icemaker operation for each applicable column.

INSTALLATION CLEARANCES – MULTIPLE COLUMNS WITH SAME DOOR SWING (HANDLE TO HINGE) TOP VIEW DOOR OPEN 115˚ HANDLE TO HINGE TOPDOOR VIEW OPEN – 115˚DOOR HANDLE OPEN TO 115˚ HINGE HANDLE TO HINGE

1 3/4" (44 mm) min. 1 3/4" (44 mm) min. spacer required* spacer required*

Handle size and position must be considered to avoid interference.

*When using the Stainless Steel Door Panel Kit w/Handle or 3/4" (19 mm) custom panels with our optional Brushed Aluminum Handle, a minimum spacer of 1 3/4" (44 mm) between units is required to open each door 115° without interference.

TOP VIEW TOPDOOR VIEW OPEN – 90˚DOOR HANDLE OPEN TO 90˚HINGE HANDLE TO HINGE

3/4" (19 mm) min. 3/4" (19 mm) min. spacer required** spacer required**

Handle size and position must be considered to avoid interference.

**When using the Stainless Steel Door Panel Kit w/Handle or 3/4" (19 mm) custom panels with our optional Brushed Aluminum Handle, the door swing can be limited to 90°, reducing the minimum spacer between units to 5/8" (16 mm).

Notes When installing multiple columns in a flush installation with the same door swing (handle to hinge), considerations must be made to avoid door swing interference. The examples shown assume a 3/4" panel and the Signature Kitchen Suite handle. Door panel thickness, handle size / position and door swing range should always be considered when determining the size of the spacer in any installation. See page 6 for details on door swing dimensions for proper planning.

Page 10 of 19 | Effective 3/20 | WCAG INTEGRATED COLUMN FLUSH INSTALLATION

CABINETRYCABINETRY PLANNING PLANNING Notes

FRAMEDCABINETRY CABINET PLANNING Integrated column appliances (NORTHFramed Cabinet AMERICA) FLUSHFlush INSET Inset are designed to accommodate nearly any type of cabinetry door Framed Cabinet Flush Inset installation. The required cutout depth depends on the desired 25" (635 mm) Cabinet door Appliance Cutout Depth cabinetry and custom panel hinges mount 25" (635 mm) execution, whether North American toCabinet the face door frame Appliance CutoutFiller Depth required with a hinges mount finished return on both styles that feature a face frame or to the face frame sidesFiller requiredof the appliance with a European styles that are frameless. finished return on both Door Panel sides of the appliance

Door Panel

FRAMELESSFrameless (European) CABINET Cabinet Flush Inset (EUROPEAN)Frameless (European) Cabinet FLUSHFlush InsetINSET

25" (635 mm) Cabinet door Appliance Cutout Depth hinges mount 25" (635 mm) toCabinet the cabinet door Appliance Cutout Depth interiorhinges mount to the cabinet interior Door Panel

Door Panel

CUSTOM PANEL PLANNING

Notes These units are designed to be customized with decorative panels. Field-installed custom door panels or an optional Stainless Steel Panel Kit is required. For Custom Panels: Use templates provided with units to pre-drill holes for mounting panel brackets (provided with unit). Adjustment screws and instructions also provided with units. Maximum Total Door Panel Weights: 30-Inch Integrated Column – 64 lbs. 24-Inch Integrated Column – 53 lbs. 18-Inch Integrated Column – 44 lbs Design Tips 4" (102 mm) will be visible on the interior sides of the return. It is recommended that both sides of each cutout panel be finished to match the cabinet exterior. If using custom panels, a custom toe kick is required. The bottom of case is unfinished. Door Handles: Handles are not included with the units. Custom handles are required for installation. Brushed Aluminum Handles are available as an optional accessory.

Page 11 of 19 | Effective 3/20 | WCAG SKSCF2401P SKSCF1801PSKSCF3001P 24-INCH INTEGRATED18" INTEGRATED30-INCH INTEGRATED INTEGRATED COLUMN COLUMN FREEZERCOLUMNCOLUMN FREEZER FREEZER FLUSH INSTALLATION

CUSTOM PANEL DIMENSIONSCUSTOM – PANELFLUSHCUSTOM DIMENSIONS INSTALLATION PANEL –DIMENSIONS FLUSH INSTALLATION – FLUSH INSTALLATION CUSTOM PANEL DIMENSIONS DUAL 18" AND 24" COLUMNDUAL 18" ANDDUAL 24" COLUMN 18" ANDDUAL 30" COLUMN 24" AND 24" COLUMNDUAL 18" AND 30"DUAL COLUMN 24" AND DUAL30" COLUMN 24" AND 30" COLUMN18-INCH INTEGRATEDDUAL 30" AND24-INCH 30" COLUMN INTEGRATED COLUMN 30-INCH INTEGRATED COLUMN COLUMN FREEZER REFRIGERATOR AND FREEZER REFRIGERATOR AND FREEZER 41 3/4" (1060 mm) 41 3/4" (1060 mm) 47 3/4"(1213 mm)47 3/4" (1213 mm) 47 3/4" (1213 mm) 53 3/4"(1365 mm)53 3/4"(1365 mm) 59 3/4"(1518 mm)

17 3/4" 23 3/4"17 3/4" 1723 3/4" 3/4" 2329 3/4" 3/4" 2317 3/4" 3/4" 29 3/4"23 3/4" 23 3/4"29 3/4" 17 3/4"29 3/4" 29 3/4" 23 3/4" 29 3/4" 29 3/4" (451 mm) (603 mm)(451 mm) (451(603 mm) mm) (603(756 mm) mm) (603(451 mm) mm) (756(603 mm) mm) (603 mm)(756 mm) (451(756 mm) mm) (756 mm) (603 mm) (756 mm) (756 mm)

79 7/8" 79 7/8" 79 7/8" 79 7/8" 79 7/8" 79 7/8" 79 7/8" 79 7/8" 79 7/8" 79 7/8" Door Panel Door PanelDoor Panel Door Panel Door Panel Door79Door 7/8" Panel Panel Door Panel Door Panel DoorDoor Panel Panel Door Panel (2029 mm)Door Panel (2029Door mm) Panel (2029 mm) (2029 mm)Door Panel (2029 mm)Door Panel (2029 mm)(2029 mm)(2029 mm) Door Panel Door Panel(2029 mm) (2029 mm) Door Panel (2029 mm)

SKSCW181RP SKSCW181RP 18" INTEGRATED 18" INTEGRATED 4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm)4" (102 mm) 4" (102 mm) 4" (102 mm) WINE4" (102 mm)COLUMN WINE COLUMN4" (102 mm) 4" (102 mm)

CUSTOM PANEL DIMENSIONS – RETROFITCUSTOM INSTALLATION PANEL DIMENSIONS – RETROFIT INSTALLATION 18-INCHCUSTOM INTEGRATED PANEL DIMENSIONS COLUMN – FLUSH INSTALLATION24-INCHCUSTOM INTEGRATED PANEL DIMENSIONS COLUMN – FLUSH INSTALLATION WINE REFRIGERATOR WINE REFRIGERATOR DUAL 18" AND 24" COLUMN DUAL 18" ANDDUAL 24" COLUMN 18" AND 30" COLUMN DUAL 18" AND 30" COLUMN 17 3/4" 23 3/4" (451 mm) (603 mm) 41 3/4" (1060 mm) 41 3/4" (1060 mm)47 3/4" (1213 mm) 47 3/4" (1213 mm) 7 1/16" 7 1/16" (179.5 mm) (179.5 mm) 17 3/4" 23 3/4" 17 3/4" 17 3/4"23 3/4" 29 3/4" 17 3/4" 29 3/4" (451 mm) (603 mm) (451 mm) (451(603 mm) mm) (756 mm) (451 mm) (756 mm)

79 7/8" 79 7/8" (2029 mm) (2029 mm) 79 7/8" 79 7/8" 79 7/8" Door Panel Door Panel Door Panel Door Panel 79 7/8" (2029 mm)Door Panel Door Panel (2029 mm) (2029Door mm) Panel Door Panel (2029 mm)

3 3/16" 3 3/16" 3 3/16" 3 3/16" (81 mm) (81 mm) (81 mm) (81 mm)

9 3/8" 9 3/8" (238 mm) (238mm)

4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm) 41 1/2" (1054 mm) 47 1/2" (1207 mm) Toekick Width Toekick Width

Page 12 of 19 | Effective 3/20 | WCAG INTEGRATEDSKSCR2401PSKSCR2401P COLUMN 24-INCH24-INCH INTEGRATED INTEGRATED COLUMN COLUMN FLUSH INSTALLATION REFRIGERATORREFRIGERATOR

CUSTOM PANELCUSTOM DIMENSIONS PANEL DIMENSIONS – FLUSH INSTALLATION – FLUSH INSTALLATION CUSTOM PANEL DIMENSIONS FOR MULTIPLE COLUMNS

DUAL 18" 18-INCH ANDDUAL 24" AND COLUMN18" AND 24-INCH 24" COLUMN DUAL 24" ANDDUAL 24" COLUMN24" 24-INCH AND 24" AND COLUMN 24-INCH DUAL 24" ANDDUAL 30" COLUMN24" AND 30" COLUMN INTEGRATED COLUMNS INTEGRATED COLUMNS 41 3/4" (1060 mm)41 3/4" (1060 mm) 47 3/4" (1213 mm)47 3/4" (1213 mm) 53 3/4"(1365 mm)53 3/4"(1365 mm)

17 3/4" 17 3/4"23 3/4" 23 3/4" 23 3/4" 23 3/4"23 3/4" 23 3/4" 23 3/4" 23 3/4" 29 3/4" 29 3/4" 23 3/4" 23 3/4" (451 mm) (451(603 mm) mm) (603 mm) (603 mm) (603 mm)(603 mm) (603 mm) (603 mm) (603 mm)(756 mm) (756 mm) (603 mm) (603 mm)

79 7/8" 79 7/8" 79 7/8" 79 7/8" 79 7/8" 79 7/8" 79 7/8" 79 7/8" Door Panel DoorDoor Panel Panel Door(2029 Panel mm) (2029 mm) Door Panel Door PanelDoor Panel Door(2029 Panel mm) (2029 mm) Door Panel Door PanelDoor Panel Door(2029 Panel mm) (2029 mm) Door Panel Door(2029 Panel mm) (2029 mm)

SKSCR2401P 24-INCH INTEGRATED COLUMN REFRIGERATOR

4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm)

CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION

DUALCUSTOM 24-INCH PANELCUSTOM DIMENSIONS AND PANEL 30-INCH DIMENSIONS – RETROFIT INSTALLATION– RETROFIT INSTALLATIONNotes DUAL 18" AND 24" COLUMN DUAL 24" AND 24" COLUMN DUAL 24" AND 30" COLUMN INTEGRATED COLUMNS These units are designed to be customized with decorative 41 3/4" (1060 mm) 47 3/4" (1213 mm) DUAL 18" ANDDUAL53 24" 3/4" COLUMN18"(1365 AND mm) 24" COLUMN DUAL 18" ANDDUALpanels. 30" COLUMN18" Field-installed AND 30" COLUMN custom door panels or an optional Stainless Steel Panel Kit is required. 17 3/4" 23 3/4" 23 3/4" 23 3/4" 23 3/4" 29 3/4" 23 3/4" 41 1/2" (1054 mm)41 1/2" (1054 mm) 47 1/2" (1207 mm)47 1/2" (1207 mm) (451 mm) (603 mm) (603 mm) (603 mm) (603 mm) (756 mm) For(603 Custom mm) Panels: Use templates provided with units to 17 3/4" 17 3/4"23 3/4" 23 3/4" 17 3/4" pre-drill17 3/4"29 holes 3/4" for mounting29 3/4" panel brackets (provided with unit). (451 mm) (451(603 mm) mm) (603 mm) (451 mm) (451 mm)(756 mm) (756 mm) Adjustment screws and instructions also provided with units. Maximum Total Door Panel Weights: 30-Inch Integrated Column – 64 lbs. 79 7/8" 79 7/8" 79 7/8" 24-Inch Integrated79 7/8" Column – 53 lbs. Door Panel Door Panel Door Panel Door Panel Door Panel Door Panel Door Panel (2029 mm) (2029 mm) (2029 mm) 18-Inch Integrated(2029 mm) Column – 44 lbs. 79 7/8" 79 7/8" 79 7/8" 79 7/8" Door Panel DoorDoor Panel Panel Door(2029 Panel mm) (2029 mm)Door Panel DesignDoor PanelDoor Tips Panel Door(2029 Panel mm) (2029 mm) 4" (102 mm) will be visible on the interior sides of the furniture return. It is recommended that both sides of each cutout panel be finished to match the cabinet exterior. If using custom panels, a custom toe kick is required. The bottom of case is unfinished.

4" (102 mm) 4" (102 mm) 4" (102 mm) Door Handles: Handles4" (102 mm) are not included with the units. Custom handles are required for installation. Brushed Aluminum Handles 4" (102 mm) 4" (102 mm) are available as an optional4" (102accessory. mm) 4" (102 mm) 41 1/2" (1054 mm)41 1/2" (1054 mm) 47 1/2" (1207 mm)47 1/2" (1207 mm) CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION Toekick WidthToekick Width Toekick WidthToekick Width

DUAL 18" AND 24" COLUMN DUAL 18" AND 30" COLUMN Page 13 of 19 | Effective 3/20 | WCAG

41 1/2" (1054 mm) 47 1/2" (1207 mm)

17 3/4" 23 3/4" 17 3/4" 29 3/4" (451 mm) (603 mm) (451 mm) (756 mm)

79 7/8" 79 7/8" Door Panel Door Panel (2029 mm) Door Panel Door Panel (2029 mm)

4" (102 mm) 4" (102 mm) 41 1/2" (1054 mm) 47 1/2" (1207 mm) Toekick Width Toekick Width SKSCF1801PSKSCF2401PSKSCF3001P SKSCW181RPSKSCW241RP INTEGRATED18-INCH INTEGRATED24-INCH COLUMN INTEGRATED30-INCH INTEGRATED18-INCH INTEGRATED24-INCH INTEGRATED COLUMN COLUMN OPTIONALCOLUMN FREEZER ACCESSORIESCOLUMN FREEZERCOLUMN FREEZERWINE REFRIGERATORWINE REFRIGERATOR

OPTIONAL ACCESSORIESOPTIONAL ACCESSORIESOPTIONAL ACCESSORIES OPTIONAL ACCESSORIESOPTIONAL ACCESSORIES OPTIONAL ACCESSORIES

Stainless Steel Panel Kit for Integrated Column Refrigerators and Freezers Units can be installed with an optional Stainless Steel Panel Kit. Kit includes one door panel, one toe kick and one handle. This kit is reversible and can be used in both Right Hand and Left Hand door swing installations. SKSPK185CS –Stainless Steel Panel Kit for 18-inch Integrated Column Freezer SKSPK245CS – Stainless Steel Panel Kit for 24-inch Integrated Column Refrigerator and Freezer SKSPK305CS – Stainless Steel Panel Kit for 30-inch Integrated Column Refrigerator and Freezer Stainless Steel Panel Kit for 18-inch Integrated Column Wine Refrigerator This unit can be installed with an optional Stainless Steel Panel Kit. Kit includes one door panel, one toe kick and one handle. Order right or left hinge option, depending on desired installation. Right Hinge – 1 Horizontal brushed hairlines for right hinge installation, opening from left to right Left Hinge – 1 Horizontal brushed hairlines for left hinge installation, opening from right to left SKSWK185RS – 18" Wine Column Stainless Kit, Right Hinge SKSWK185LS – 18" Wine Column Stainless Kit, Left Hinge SKSWK245RS – 24" Wine Column Stainless Kit, Right Hinge SKSWK245LS – 24" Wine Column Stainless Kit, Left Hinge Handles for Use With Custom Panels SKSHK310HS – 31 11/16" (805 mm) Medium Handle – Brushed Aluminum SKSHK480HS – 48" (1219 mm) Long Handle – Brushed Aluminum Joining Kit for Dual/Multiple Column Installation SKSFJ800P – This kit is required for installation when a wine column is installed with another wine column, refrigerator column or French door column. This kit is included with all freezer columns.

Page 14 of 19 | Effective 3/20 | WCAG INTEGRATED COLUMN FLUSHSKSFD3604P INSTALLATION 36-INCH BUILT-IN FRENCH DOOR REFRIGERATOR

36-INCH BUILT-IN FRENCH DOOR REFRIGERATOR

CUSTOM PANEL DIMENSIONS CUSTOM PANEL DIMENSIONS 17 13/16" 17 13/16" (452 mm) (452 mm) Notes These units are designed to be customized with decorative panels. Field- installed custom door panels or an optional Stainless Steel Panel Kit is required. For Custom Panels: Use templates provided with units to pre-drill holes for mounting panel brackets (provided with unit). Adjustment screws and instructions also provided with units.

A A 49 3/8" Maximum Panel Weight: (1254 mm) A – Fresh food door panels: 33 lbs. B – Convertible drawer panel: 22 lbs. C – Freezer drawer panel: 33 lbs. Design Tips 4" (102 mm) will be visible on the interior sides of the furniture return. It is 9 1/16" B (230 mm) recommended that both sides of each cutout panel be finished to match the cabinet exterior. If using custom panels, a custom toe kick is required. The bottom of case is C 21" (533 mm) unfinished. Door Handles: Handles are not included with the refrigerator. Custom handles SKSFD3604P are required for installation. Brushed Aluminum Handles are available as an 4" (102 mm) 36" INTEGRATED FRENCH optional accessory. 35 3/4" DOOR (908REFRIGERATOR mm)

OPTIONAL ACCESSORIES OPTIONAL ACCESSORIES SKSPK360FS – Stainless Steel Panel Kit for 36-inch Built-in French Door Refrigerator This refrigerator can be installed with an optional Stainless Steel Panel Kit. Kit includes two fresh food door panels, one convertible drawer panel, one freezer drawer panel, one toe kick and four handles. Handles for Use With Custom Panels SKSHK310HS – 31 11/16" (805 mm) Medium Handle – Brushed Aluminum

Page 15 of 19 | Effective 3/20 | WCAG 18" FREEZER 18" FREEZER INTEGRATEDAND COLUMN AND RETROFIT24" REFRIGERATOR INSTALLATION COLUMN 30" REFRIGERATOR COLUMN

CUTOUT DIMENSIONS – RETROFIT INSTALLATION CUTOUT DIMENSIONS – RETROFIT INSTALLATION CUTOUT DIMENSIONS – RETROFIT INSTALLATION Notes 18" FREEZER AND The 18" integrated column freezer 41 1/2" (1054 mm) 24" REFRIGERATOR has an actual width of 17 1/2" (44547 1/2" (1207 mm) finished width COLUMN mm) to accommodate a retrofit finished width installation. This will allow you to combine the 18" freezer column 4" 4" (102 mm) 24" (610 mm) with(102 a 24"mm) refrigerator column in a finished min. depth 41 1/2"finished (1054 mm) cutout or with a 24" (610 mm) return* return* min. depth 30" refrigerator column in a 47 1/2" (1207 mm) cutout. Electrical

84" A minimum 15 amp (115V, 60Hz) (2134 mm) 84" power supply is required for each (2134 mm) 5" 5" (127 mm) individual column.(127 mm) An individual electrical electrical 2 3/4" properly grounded branch circuit2 3/4" location (70 mm) location (70 mm) or circuit breaker is recommended. Install a properly grounded 3-prong 18" FREEZER 18" FREEZER 4" (102 mm) 4" (102 mm) AND AND water location electrical receptaclewater recessed location into the back wall. Electrical must be 24" REFRIGERATOR COLUMN 30" REFRIGERATOR COLUMN 1 3/8" (35 mm) located on rear 1wall 3/8" as (35 shown. mm) Note: GFI (ground fault interrupter) is not recommended. CUTOUT DIMENSIONS – RETROFIT INSTALLATION CUTOUT DIMENSIONS – RETROFIT INSTALLATION *A minimum 4" (102 mm) finished return that matches the cabinet exterior is *WaterA minimum Line 4" (102 mm) finished return that matches the cabinet exterior is recommended on recommended on all sides and the top of the cutout opening. The shaded all sides and the top of the cutout opening. The shaded area will be visible after installation. 18" FREEZERarea will be AND visible after installation. A cold water supply is required for 41 1/2" (1054 mm) An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns. 30" REFRIGERATOR 47 1/2" (1207 mm) water dispenser and automatic finished width An optional Frame Kit can be used to provide a finished look to unfinished finished width COLUMNcabinet returns. icemaker operation for each individual column. Water pressure must be between 20 and 120 p.s.i. 4" 4" (102 mm) 24" (610 mm) (102 mm) Tubing should be long enough to finished min. depth finished 24" (610 mm) return* return* min. depth extend to the front of the unit. Allow enough tubing to accommodate a bend leading into the water line connection.

84" Water line can enter an opening (2134 mm) 84" (2134 mm) through floor or back wall. 5" 5" (127 mm) (127 mm) Install a shut-off valve between the electrical 2 3/4" electrical 2 3/4" location (70 mm) location (70 mm) icemaker water valve and cold water supply in the home.

4" (102 mm) 4" (102 mm) water location water location

1 3/8" (35 mm) 1 3/8" (35 mm)

*A minimum 4" (102 mm) finished return that matches the cabinet exterior is *A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on recommended on all sides and the top of the cutout opening. The shaded all sides and the top of the cutout opening. The shaded area will be visible after installation. area will be visible after installation. Page 16 of 19 | Effective 3/20 | WCAG An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns. An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns. INTEGRATED COLUMN RETROFITINSTALLATION INSTALLATION CLEARANCES – RETROFIT INSTALLATION 18-INCH INTEGRATED COLUMN FREEZER AND 24-INCH INTEGRATED COLUMN REFRIGERATOR INSTALLATION CLEARANCES – RETROFIT INSTALLATION

TOP18-INCH VIEW INTEGRATED COLUMN FREEZER INSTALLATIONAND CLEARANCES – RETROFIT INSTALLATION 24-INCH INTEGRATED COLUMN41 1/2" REFRIGERATOR cutout (1054 mm) TOP CUTOUT VIEW – 18-INCH INTEGRATED COLUMN FREEZER

ANDTOP 24-INCH VIEW INTEGRATED COLUMN REFRIGERATOR 24" 11 3/8"* (610 mm) 24" 8 3/4"* (288 mm) (610 mm) (223 mm) 41 1/2" cutout (1054 mm) 1/8" 1/8" (3 mm) (3 mm) Optional Frame Kit 1 1/4"* min. min. 1 1/4"* 24" (32 mm) 11(32 3/8"* mm) (610 mm) SKSFK800CS can 24" 8 3/4"* (288 mm) (610 mm) (223 mm) be installed for a 1/8"17 3/4" 23 3/4" 1/8" finished look. (3 mm)(451 mm) (603 mm)(3 mm) Optional Frame Kit 1 1/4"* 115° min. min. 1115° 1/4"* (32 mm)20 1/4" (32 mm) SKSFK800CS can (514 mm) be installed for a 25 1/2" 17 3/4" 23 3/4" (648 mm) finished look. 90° (451 mm) (603 mm) 90° 115° 115° 20 1/4" (514 mm) 25 1/2" 90° 90° (648 mm) *Door handle must be added to this dimension. ** Varies depending on the thickness of the 3/4" custom cabinet panel. The door panels in the (19 mm)** optional Signature Kitchen Suite stainless Notes *steelDoor doohandler panel must kit be are added 3/4" (19to this mm) dimension. thick. ** Varies depending on the thickness of the In retrofit installations where the cutout 3/4" custom cabinet panel. The door panels in the (19 mm)** is only 24" (610 mm) deep, the front face optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick. of the unit extends approximately 3/4" (19 mm) beyond 24" (610 mm) depth adjacent cabinets for a proud appearance. 18-INCH INTEGRATED COLUMN FREEZER AND The unit can be installed with 3/4" custom 30-INCH INTEGRATED COLUMN REFRIGERATOR TOP CUTOUT VIEW – 18-INCH INTEGRATED COLUMN FREEZER  panel or optional stainless steel panel kit. An optional Frame Kit is recommended for ANDTOP18-INCH 30-INCH VIEW INTEGRATED INTEGRATED COLUMN COLUMN FREEZER REFRIGERATOR AND a finished look. 30-INCH INTEGRATED COLUMN47 REFRIGERATOR 1/2" cutout (1207 mm)

TOP VIEW 24" 13 7/8"* (610 mm) 24" 8 3/4"* (352 mm) (610 mm) (223 mm) 47 1/2" cutout (1207 mm) 1/8" 1/8" (3 mm) (3 mm) Optional Frame Kit min. 1 1/4"* min. 1 1/4"* 24" SKSFK800CS can (32 mm) 13(32 7/8"* mm) (610 mm) 24" 8 3/4"* (352 mm) be installed for a (610 mm) (223 mm) finished look. 1/8"17 3/4" 29 3/4" 1/8" (3 mm)(451 mm) (756 mm) (3 mm) Optional Frame Kit min. 1 1/4"* 115° min. 1115° 1/4"* SKSFK800CS can (32 mm)20 1/4" (32 mm) (514 mm) be installed for a 32 1/4" finished look. 17 3/4" 29 3/4" (819 mm) 90° (451 mm) (756 mm) 90° 115° 115° 20 1/4" (514 mm) 32 1/4" 90° 90° (819 mm)

*Door handle must be added to this dimension. ** Varies depending on the thickness of the custom cabinet 3/4" panel. The door panels in the optional Signature Kitchen (19 mm)** Suite stainless steel door panel kit are 3/4" (19 mm) thick. *Door handle must be added to this dimension. ** Varies depending on the thickness of the custom cabinet Page 17 of 19 | Effective 3/20 | WCAG3/4" panel. The door panels in the optional Signature Kitchen (19 mm)** Suite stainless steel door panel kit are 3/4" (19 mm) thick. SKSCR2401P 24-INCH INTEGRATED COLUMN REFRIGERATOR

CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION

DUAL 18" AND 24" COLUMN DUAL 24" AND 24" COLUMN DUAL 24" AND 30" COLUMN

41 3/4" (1060 mm) 47 3/4" (1213 mm) 53 3/4"(1365 mm)

17 3/4" 23 3/4" 23 3/4" 23 3/4" 23 3/4" 29 3/4" 23 3/4" (451 mm) (603 mm) (603 mm) (603 mm) (603 mm) (756 mm) (603 mm)

79 7/8" 79 7/8" 79 7/8" 79 7/8" Door Panel Door Panel (2029 mm) Door Panel Door Panel (2029 mm) Door Panel Door Panel (2029 mm) Door Panel (2029 mm)

INTEGRATED COLUMN RETROFIT INSTALLATION 4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm)

CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION

DUAL 18" 18-INCH AND 24" AND COLUMN 24-INCH DUAL 18" 18-INCH AND 30" AND COLUMN 30-INCH INTEGRATED COLUMNS INTEGRATED COLUMNS 41 1/2" (1054 mm) 47 1/2" (1207 mm)

17 3/4" 23 3/4" 17 3/4" 29 3/4" (451 mm) (603 mm) (451 mm) (756 mm)

79 7/8" 79 7/8" Door Panel Door Panel (2029 mm) Door Panel Door Panel (2029 mm)

4" (102 mm) 4" (102 mm) 41 1/2" (1054 mm) 47 1/2" (1207 mm) Toekick Width Toekick Width

Notes Design Tips These units are designed to be customized with 4" (102 mm) will be visible on the interior sides of the decorative panels. Field-installed custom door panels or furniture return. It is recommended that both sides of each an optional Stainless Steel Panel Kit is required. cutout panel be finished to match the cabinet exterior. For Custom Panels: Use templates provided with units to If using custom panels, a custom toe kick is required. The pre-drill holes for mounting panel brackets (provided with bottom of case unit). Adjustment screws and instructions also provided is unfinished. with units. In retrofit installations where the cutout is 24" (610 mm) Maximum Total Door Panel Weights: deep, the optional Frame Kit is recommended to provide a 30-Inch Integrated Column – 64 lbs. finished look. 24-Inch Integrated Column – 53 lbs. Door Handles: Handles are not included with the units. 18-Inch Integrated Column – 44 lbs. Custom handles are required for installation. Brushed Aluminum Handles are available as an optional accessory.

Page 18 of 19 | Effective 3/20 | WCAG INTEGRATED COLUMN RETROFIT INSTALLATION

OPTIONALOPTIONAL ACCESSORIES ACCESSORIES – RETROFIT – RETROFIT INSTALLATION INSTALLATION

SKSFK800CS – Frame Kit All units can be installed in a 24" (610 mm) deep cutout with an optional frame kit. This kit includes two 80" (2032 mm) brushed aluminum side trim pieces. Each trim piece is 5" (127 mm) deep with a 1/8" (3 mm) front face. SKSFJ800P - Joining Kit for Dual/Multiple Column Installation This kit is required for installation when a wine column is installed with another wine column, refrigerator column or French door column. This kit is included with all freezer columns. Design Tips The Stainless Steel Panel Kit may be used in a retrofit 24" (610 mm) cutout depth installation. For retrofit / replacement installations where the existing cutout is 24" (610 mm) deep, the optional frame kit is recommended.

© 2020 Signature Kitchen Suite. All rights reserved. Design, features and specifications are subject to change without notice. Specifications are for planning purposes only. Consult the product’s installation instructions for final dimensional data and other details prior to making cutouts or custom panels. Consult with a heating and ventilation engineer for your specific ventilation requirements. Non-metric weights and measurements are approximate. Smart features require Internet access. 1-855-790-6655 | www.signaturekitchensuite.com

Effective 3/20 | WCAG