ANNEXURE TO TENDER NO : DPS/ MRPU/IGCAR/ MIA/7390

1. ULINK pro Debug and Trace Unit (or equivalent) - 2 Nos. • Target voltage range: 1.2V - 3.3V, 5V tolerant • Support for 5V devices using a 5V Adapter • USB powered • Debugging Support: o Serial Wire Debug (Cortex-M) o Data Trace (Cortex-M with SWO) o Instruction Trace (Cortex-M3/4/7/33) • Target Connectors: o 10-pin (0.05") - Cortex Debug Connector o 20-pin (0.10") - ARM Standard JTAG Connector o 20-pin (0.05") - Cortex Debug + ETM Connector • Supported Device Families o ARM7, ARM9 o ARM Cortex-A5/A7/A9 o ARM Cortex-M • RAM Breakpoints Unlimited • ROM Breakpoints (ARM7/9) 2 max • ROM Breakpoints (Cortex-M) 6 max • Execution Breakpoints (Set While Executing) True • Access Breakpoints (ARM7/9) 2 max • Access Breakpoints (Cortex-M) (With value) 4 max • JTAG Clock ≤ 50 MHz • Memory R/W ≈ 1 MB/s • Flash R/W 32 KB/s • Trace Streaming 800 Mb/s

2. J-Link PRO (or equivalent) - 2 Nos. • Ethernet interface • USB 2.0 Hi-Speed interface • Powered through USB or power supply • Web interface for TCP/IP configuration • Automatic core recognition • Standard 20-pin target connector • Supported CPUs: ARM7/9/11, Cortex-A5/A8/A9, Cortex-M0/M1/M3/M4/M7, Cortex- R4/R5, Microchip PIC32 and Renesas RX100/RX200/RX610/RX621/RX62N/RX62T/RX630/RX631/RX63N • Maximum target interface speed 50 MHz • Maximum SWO sampling speed 100 MHz • Download speed up to 3 MByte/second • Support for adaptive clocking • All target interface signals should be monitored, target voltage should be measured • Support for multiple devices • Fully plug and play compatible • Wide target voltage range: 1.2V - 5V • Galvanic isolation from host system via Ethernet • Free software updates1, 2 years of support • Should have support for following modes of debugging: o Ethernet o USB o JTAG interface o SWD interface o SWO interface o Microchip ICSP interface o Renesas FINE interface

3. -ICE (or equivalent) - 2 Nos. • Full source level debugging in Atmel Studio • Up to 128 software breakpoints • Supports all built in hardware breakpoints in the target • Supports programming and debugging of all Atmel AVR UC3 32-bit • Supports programming and debugging of all 8-bit AVR XMEGA devices • Supports programming and debugging of all 8-bit Atmel megaAVR® and tinyAVR devices with OCD • Supports programming and debugging of all SAM ARM Cortex-M based microcontrollers • Draws less than 3mA from target VTref when using debugWIRE interface and less than 1mA for all other interfaces • Supports JTAG clock frequencies from 32kHz to 7.5MHz • Supports PDI clock frequencies from 32kHz to 7.5MHz • Supports debugWIRE baud rates from 4kbit/s to 0.5Mbit/s • Supports aWire baud rates from 7.5kbit/s to 7Mbit/s • Supports SPI clock frequencies from 8kHz to 5MHz • Supports SWD clock frequencies from 32kHz to 2MHz • ITM serial trace capture at up to 3MB/s • USB 2.0 high-speed host interface • USB powered • Target operating voltage range of 1.62V to 5.5V • Provides both ARM Cortex debug connector (10 pin) pin out and AVR JTAG connector pin out

4. Wireless HART Mote Module with MMCX Antenna Connector (LTP5902IPC-WHMA1B2#PBF) (or equivalent) - 20 Nos • Operating Voltage: 3-3.6V • Incorporates a 2.4 GHz, IEEE 802.15.4 System-on-Chip, • Compliant to the Wireless HART standard (IEC62591) • Industrial grade • MMCX antenna connector • Runs DUST’s Embedded Networking Software • Data Rate Max: 250Kbps • Module Interface: SPI, UART • Sensitivity dBm: -93dBm • Frequency Max: 2.4835GHz • CLI UART and API UART interface • Range: 100m (indoor), 300m (Outdoor) • No. of Channels: 15 • PER ≤ 0.001

5. Wi-Spy 2.4x with Chanalyzer 5 (or equivalent) - 1 No. • Default Frequency Range: 2.400 to 2.495 GHz • Min/Max Frequencies: 2300-2700 Mhz • Amplitude Range: -110 dBm to -6.5 dBm • Antenna : RP-SMA • Compatible Software: Chanalyzer 5

General Terms and conditions

1. Taxes should be clearly mentioned in the quote. 2. The materials should be delivered to Stores, IGCAR, Kalpakkam 3. The above mentioned items should be delivered within 2 months from the date of Purchase Order. 4. Selective purchase based on lowest quote can be made on individual items.