OPTICAL SUPER-RESOLUTION and PERIODICAL FOCUSING EFFECTS by DIELECTRIC MICROSPHERES by Arash Darafsheh a Dissertation Submitted

Total Page:16

File Type:pdf, Size:1020Kb

Load more

OPTICAL SUPER-RESOLUTION AND PERIODICAL FOCUSING EFFECTS BY DIELECTRIC MICROSPHERES by Arash Darafsheh A dissertation submitted to the faculty of The University of North Carolina at Charlotte in partial fulfillment of the requirements for the degree of Doctor of Philosophy in Optical Science and Engineering Charlotte 2013 Approved by: ______________________________ Dr. Vasily N. Astratov ______________________________ Dr. Michael A. Fiddy ______________________________ Dr. Gregory J. Gbur ______________________________ Dr. Angela D. Davies ______________________________ Dr. Christopher J. Evans ii ©2013 Arash Darafsheh ALL RIGHTS RESERVED iii ABSTRACT ARASH DARAFSHEH. Optical super-resolution and periodical focusing effects by dielectric microspheres. (Under the direction of DR. VASILY N. ASTRATOV) Optical microscopy is one of the oldest and most important imaging techniques; however, its far-field resolution is diffraction-limited. In this dissertation, we proposed and developed a novel method of optical microscopy with super-resolution by using high- index dielectric microspheres immersed in liquid and placed on the surface of the structures under study. We used barium titanate glass microspheres with diameters of D~2-220 μm and refractive indices n~1.9-2.1 to discern minimal feature sizes ~/4 (down to ~/7) of various photonic and plasmonic nanostructures, where is the illumination wavelength. We studied the magnification, field of view, and resolving power, in detail, as a function of sphere sizes. We studied optical coupling, transport, focusing, and polarization properties of linear arrays of dielectric spheres. We showed that in arrays of spheres with refractive index n=√3, a special type of rays with transverse magnetic (TM) polarization incident on the spheres under the Brewster’s angle form periodically focused modes with radial polarization and 2D period, where D is the diameter of the spheres. We showed that the formation of periodically focused modes in arrays of dielectric spheres gives a physical explanation for beam focusing and extraordinarily small attenuation of light in such chains. We showed that the light propagation in such arrays is strongly polarization- dependent, indicating that such arrays can be used as filters of beams with radial polarization. The effect of forming progressively smaller focused beams was experimentally observed in chains of sapphire spheres in agreement with the theory. iv We expanded the concept of periodically focused modes to design a practical device for ultra-precise contact-mode laser tissue-surgery, with self-limiting ablation depth for potential application in retina surgery. By integrating arrays of dielectric spheres with infrared hollow waveguides and fibers, we fabricated prototypes of the designs and tested them with an Er:YAG laser. Furthermore, we proposed another design based on conical arrays of dielectric spheres to increase the coupling efficiency of the probe. v ACKNOWLEDGMENTS I am very thankful to my advisor, Dr. Vasily N. Astratov, for his advice and support; for his constructive criticisms on my presentations, papers, and dissertation; and for the scientific discussions we had during my study at the University of North Carolina at Charlotte. Without his help, this dissertation work would have not been possible. I thank members of my committee, Dr. Michael A. Fiddy, Dr. Gregory J. Gbur, Dr. Angela D. Davies, and Dr. Christopher J. Evans for accepting to serve in the committee and their time and comments. I am grateful to Dr. Nathaniel M. Fried for his guidance in surgical applications of lasers and fruitful discussions, to Dr. Michael A. Fiddy for discussions which initiated the work on super-resolution imaging, and to Dr. Angela D. Davies for sharing high numerical-aperture microscope objectives. During my graduate studies, I enjoyed discussing scientific issues with my fellow Mesophotonics Laboratory members, Dr. Oleksiy Svitelskiy, Kenneth W. Allen, S. Adam Burand, and Yangcheng Li. I am grateful for the opportunity to be involved in a number of collaborations with different groups with which Mesophotonics laboratory has collaborative works. I also would like to thank fellow graduate students Thomas C. Hutchens and Mona Mayeh for productive discussions. I am thankful to Dr. Lou Deguzman, Scott Williams, Dr. Awad Gerges, and Dr. Robert Hudgins for showing me how to operate the equipment in the Optics center at the UNCC. I would like to thank the staff of the Physics department and the Optics center, Wendy Ramirez and Mark Clayton, for helping me with the administrative issues. vi I was supported through a fellowship from TIAA-CREFF for Fall 2008 and Spring 2009 and by GASP award from Fall 2008 to Spring 2013. My graduate assistantship in Dr. Astratov’s Mesophotonics Laboratory was supported through his grants from NSF, NIH, and ARO. I am grateful to Dr. Faramarz Farahi and Dr. Mohammad A. Kazemi for their guidance and introducing the UNCC Optical Science and Engineering graduate program to me. I deeply thank my family for their endless love and support which motivated me to pursue my academic education up to this level. vii DEDICATION To my parents, Dr. Rafat Rafiei and Dr. M. Reza Darafsheh, for their endless love and support. viii TABLE OF CONTENTS LIST OF FIGURES xii LIST OF ABBREVIATIONS xxiii CHAPTER 1: INTRODUCTION 1 1.1: Outline and Overview of the Dissertation 1 1.2: Super-resolution Microscopy Techniques 3 1.2.1: Diffraction Limit and Resolution Criteria 4 1.2.2: Near-field Techniques 10 1.2.3: Immersion Microscopy Techniques 11 1.2.4: Microsphere Nanoscope 13 1.3: Resonant and Non-resonant Optical Properties of Dielectric Spheres 17 1.3.1: Whispering Gallery Modes in Spherical Cavities 17 1.3.2: Photonic Nanojets and Nanojet Induced Modes 23 1.4: Focusing Surgical Microprobes 42 1.4.1: Erbium:YAG Laser for Medical Applications 46 1.4.2: Infrared Waveguides 48 1.4.2.1: Classification of Infrared Fibers and Waveguides 48 1.4.2.2: Infrared Hollow Waveguides 50 1.4.2.3: Quantitative Parameters of Infrared Waveguides 51 1.5: Summary 53 CHAPTER 2: SUPER-RESOLUTION IMAGING BY LIQUID-IMMERSED 57 HIGH-INDEX MICROSPHERES 2.1: Introduction 57 ix 2.2: Samples 59 2.3: Microscopy Technique 64 2.4: Spatial Resolution 67 2.5: Lateral Magnification and Field-of-View 69 2.6: Polarization Effects 72 2.7: Resolution Gain and Effect of the NA of the Objective Lens 73 2.8: Comparison with Solid Immersion Lens Microscopy 76 2.9: Comparison with Confocal Microscopy 80 2.10: Conclusions 82 CHAPTER 3: OPTICAL CHARACTERISTICS OF LINEAR ARRAYS OF 84 DIELECTRIC SPHERES 3.1: Introduction 84 3.2: Periodically Focused Modes 88 3.3: Description of the Modeling Technique 94 3.4: Optical Characteristics 97 3.4.1: Optical Power Transport 98 3.4.2: Focusing 101 3.4.3: State of Polarization 105 3.5: Disorder Effects 110 3.5.1: Shape Disorder (Deviation from a Perfect Sphere) 111 3.5.2: Spacing Disorder (Presence of Gap between Spheres) 112 3.5.3: Scattering inside Spheres and from Their Surfaces 112 3.5.4: Size Disorder 113 3.6: Experimental Results 116 x 3.6.1: Assembly of Sphere-chains 116 3.6.2: Focusing Properties 118 3.6.3: Optical Power Transport 123 3.6.4: Phase Properties 126 3.7: Conclusions 130 CHAPTER 4: DESIGN, FABRICATION, AND TESTING OF FOCUSING 133 MULTIMODAL MICROPROBES 4.1: Introduction 133 4.2: Fiber-integrated Microprobes Formed by Uniform Sphere-arrays 136 4.2.1: Modeling Technique 136 4.2.2: Optical Properties 140 4.2.2.1: Fiber-to-microsphere Separation 140 4.2.2.2: Optical Focusing and Power Transport 143 4.2.2.3: Self-limiting Mechanism 147 4.2.2.4: Polarization Properties 151 4.2.3: Fabrication and Testing 153 4.3: A Sub-optimal Microprobe Design for Preliminary ex vivo Testing 158 4.4: Microprobe Designs Using Conical Arrays of Spheres 160 4.4.1: Modeling Technique 161 4.4.2: Optical Properties 163 4.5: Conclusions 167 CHAPTER 5: CONCLUSIONS AND FUTURE DIRECTIONS 169 REFERENCES 175 APPENDIX A: LIST OF PUBLICATIONS 195 xi APPENDIX B: SOME APPLICATIONS OF PHOTONIC NANOJETS 199 APPENDIX C: DERIVATION OF PFMS CONDITIONS 211 APPENDIX D: MATRIX OPTICS FOR SPHERE-CHAINS 215 APPENDIX E: SPHERES SIZES IN A CONICAL DESIGN 223 xii LIST OF FIGURES FIGURE 1.1 Numerical aperture (NA) of a lens. 4 FIGURE 1.2 Illustration of the Abbe’s theory where diffraction orders pass 6 through (a) or stopped by (b) the lens pupil [42]. Reprinted with permission. © 2003 Imperial College Press. FIGURE 1.3 Rayleigh criterion for a (a) square and (b) circular aperture. 8 FIGURE 1.4 (a) An objective lens, (b) a hemispherical solid immersion lens 12 (h-SIL), and (c) a super-spherical solid immersion lens (s-SIL). FIGURE 1.5 (a) Schematic of an optical nanoscope with microspheres 14 placed on top of the sample. The spheres collect the near-field object information and form virtual images that are captured by the objective lens. (b) Optical microscopy of a Blu-ray® disk without SIL or sphere, (c) with a 0.5 mm SIL, (d) with a 2.5 mm SIL, and (e) with a 4.74 μm silica microsphere [63]. Reprinted with permission. © 2011 Macmillan Publishers Ltd: Nature Communications. FIGURE 1.6 (a) Super-resolution strength vs. size parameter q. (b) Intensity 15 distributions calculated for a freestanding s-SIL, a freestanding sphere, and a sphere on surface of a 40-nm-thick gold film (D=4.74 μm, n=1.46, and λ=600 nm). (c) FWHM of foci for s- SIL (blue), sphere (red), and sphere on substrate (green). (d) Virtual image magnification vs. sphere diameter D [63]. Reprinted with permission. © 2011 Macmillan Publishers Ltd: Nature Communications. FIGURE 1.7 (a-c) Schematics of a single sphere on a substrate illustrating 21 intensity maxima distributions for WGMs with different m.
Recommended publications
  • About Resolution

    About Resolution

    pco.knowledge base ABOUT RESOLUTION The resolution of an image sensor describes the total number of pixel which can be used to detect an image. From the standpoint of the image sensor it is sufficient to count the number and describe it usually as product of the horizontal number of pixel times the vertical number of pixel which give the total number of pixel, for example: 2 Image Sensor & Camera Starting with the image sensor in a camera system, then usually the so called modulation transfer func- Or take as an example tion (MTF) is used to describe the ability of the camera the sCMOS image sensor CIS2521: system to resolve fine structures. It is a variant of the optical transfer function1 (OTF) which mathematically 2560 describes how the system handles the optical infor- mation or the contrast of the scene and transfers it That is the usual information found in technical data onto the image sensor and then into a digital informa- sheets and camera advertisements, but the question tion in the computer. The resolution ability depends on arises on “what is the impact or benefit for a camera one side on the number and size of the pixel. user”? 1 Benefit For A Camera User It can be assumed that an image sensor or a camera system with an image sensor generally is applied to detect images, and therefore the question is about the influence of the resolution on the image quality. First, if the resolution is higher, more information is obtained, and larger data files are a consequence.
  • High-Aperture Optical Microscopy Methods for Super-Resolution Deep Imaging and Quantitative Phase Imaging by Jeongmin Kim a Diss

    High-Aperture Optical Microscopy Methods for Super-Resolution Deep Imaging and Quantitative Phase Imaging by Jeongmin Kim a Diss

    High-Aperture Optical Microscopy Methods for Super-Resolution Deep Imaging and Quantitative Phase Imaging by Jeongmin Kim A dissertation submitted in partial satisfaction of the requirements for the degree of Doctor of Philosophy in Engineering { Mechanical Engineering and the Designated Emphasis in Nanoscale Science and Engineering in the Graduate Division of the University of California, Berkeley Committee in charge: Professor Xiang Zhang, Chair Professor Liwei Lin Professor Laura Waller Summer 2016 High-Aperture Optical Microscopy Methods for Super-Resolution Deep Imaging and Quantitative Phase Imaging Copyright 2016 by Jeongmin Kim 1 Abstract High-Aperture Optical Microscopy Methods for Super-Resolution Deep Imaging and Quantitative Phase Imaging by Jeongmin Kim Doctor of Philosophy in Engineering { Mechanical Engineering and the Designated Emphasis in Nanoscale Science and Engineering University of California, Berkeley Professor Xiang Zhang, Chair Optical microscopy, thanks to the noninvasive nature of its measurement, takes a crucial role across science and engineering, and is particularly important in biological and medical fields. To meet ever increasing needs on its capability for advanced scientific research, even more diverse microscopic imaging techniques and their upgraded versions have been inten- sively developed over the past two decades. However, advanced microscopy development faces major challenges including super-resolution (beating the diffraction limit), imaging penetration depth, imaging speed, and label-free imaging. This dissertation aims to study high numerical aperture (NA) imaging methods proposed to tackle these imaging challenges. The dissertation first details advanced optical imaging theory needed to analyze the proposed high NA imaging methods. Starting from the classical scalar theory of optical diffraction and (partially coherent) image formation, the rigorous vectorial theory that han- dles the vector nature of light, i.e., polarization, is introduced.
  • Preview of “Olympus Microscopy Resou... in Confocal Microscopy”

    Preview of “Olympus Microscopy Resou... in Confocal Microscopy”

    12/17/12 Olympus Microscopy Resource Center | Confocal Microscopy - Resolution and Contrast in Confocal … Olympus America | Research | Imaging Software | Confocal | Clinical | FAQ’s Resolution and Contrast in Confocal Microscopy Home Page Interactive Tutorials All optical microscopes, including conventional widefield, confocal, and two-photon instruments are limited in the resolution that they can achieve by a series of fundamental physical factors. In a perfect optical Microscopy Primer system, resolution is restricted by the numerical aperture of optical components and by the wavelength of light, both incident (excitation) and detected (emission). The concept of resolution is inseparable from Physics of Light & Color contrast, and is defined as the minimum separation between two points that results in a certain level of contrast between them. In a typical fluorescence microscope, contrast is determined by the number of Microscopy Basic Concepts photons collected from the specimen, the dynamic range of the signal, optical aberrations of the imaging system, and the number of picture elements (pixels) per unit area in the final image. Special Techniques Fluorescence Microscopy Confocal Microscopy Confocal Applications Digital Imaging Digital Image Galleries Digital Video Galleries Virtual Microscopy The influence of noise on the image of two closely spaced small objects is further interconnected with the related factors mentioned above, and can readily affect the quality of resulting images. While the effects of many instrumental and experimental variables on image contrast, and consequently on resolution, are familiar and rather obvious, the limitation on effective resolution resulting from the division of the image into a finite number of picture elements (pixels) may be unfamiliar to those new to digital microscopy.
  • Super-Resolution Optical Imaging Using Microsphere Nanoscopy

    Super-Resolution Optical Imaging Using Microsphere Nanoscopy

    Super-resolution Optical Imaging Using Microsphere Nanoscopy A thesis submitted to The University of Manchester For the degree of Doctor of Philosophy (PhD) in the Faculty of Engineering and Physical Sciences 2013 Seoungjun Lee School of Mechanical, Aerospace and Civil Engineering Super-resolution optical imaging using microsphere nanoscopy Table of Contents Table of Contents ...................................................................................................... 2 List of Figures and Tables ....................................................................................... 7 List of Publications ................................................................................................. 18 Abstract .................................................................................................................... 19 Declaration ............................................................................................................... 21 Copyright Statement ............................................................................................... 22 Acknowledgements ................................................................................................. 23 Dedication ............................................................................................................... 24 1 Introduction ...................................................................................................25 1.1 Research motivation and rationale ........................................................25 1.2
  • Overcoming the Diffraction-Limited Spatio-Angular Resolution Tradeoff

    Overcoming the Diffraction-Limited Spatio-Angular Resolution Tradeoff

    Variable Aperture Light Field Photography: Overcoming the Diffraction-limited Spatio-angular Resolution Tradeoff Julie Chang1 Isaac Kauvar1 Xuemei Hu1,2 Gordon Wetzstein1 1Stanford University 2 Tsinghua University Abstract Small-f-number Large-f-number Light fields have many applications in machine vision, consumer photography, robotics, and microscopy. How- ever, the prevalent resolution limits of existing light field imaging systems hinder widespread adoption. In this pa- per, we analyze fundamental resolution limits of light field cameras in the diffraction limit. We propose a sequen- Depth-of-Field 10 tial, coded-aperture-style acquisition scheme that optimizes f/2 f/5.6 the resolution of a light field reconstructed from multiple f/22 photographs captured from different perspectives and f- 5 Blur-size-[mm] number settings. We also show that the proposed acquisi- 0 100 200 300 400 tion scheme facilitates high dynamic range light field imag- Distance-from-Camera-Lens-[mm] ing and demonstrate a proof-of-concept prototype system. Figure 1. Photographs captured with different f-number settings With this work, we hope to advance our understanding of exhibit different depths of field and also diffraction-limited resolu- the resolution limits of light field photography and develop tion for in-focus objects (top row). This effect is most pronounced practical computational imaging systems to overcome them. for macro photography, such as illustrated for a 50 mm lens fo- cused at 200 mm (bottom plot). Using multiple photographs cap- tured from different perspectives and with different f-number set- tings, the proposed method seeks to recover a light field with the 1.
  • Improved Modulation Transfer Function Evaluation Method of a Camera at Any Field Point with a Scanning Tilted Knife Edge

    Improved Modulation Transfer Function Evaluation Method of a Camera at Any Field Point with a Scanning Tilted Knife Edge

    Improved Modulation Transfer Function evaluation method of a camera at any field point with a scanning tilted knife edge PRESENTED AT SPIE SECURITY+DEFENSE 2020 BY ETIENNE HOMASSEL, TECHNICAL PRODUCT MANAGER HGH, 10 10 rue Maryse Bastié 91430 IGNY –France +33 (1) 69 35 47 70 [email protected] Improved Modulation Transfer Function evaluation method of a camera at any field point with a scanning tilted knife edge Etienne Homassel, Catherine Barrat, Frédéric Alves, Gilles Aubry, Guillaume Arquetoux HGH Systèmes Infrarouges, France ABSTRACT Modulating Transfer Function (MTF) has always been very important and useful for objectives quality definition and focal plane settings. This measurand provides the most relevant information on the optimized design and manufacturing of an optical system or the correct focus of a camera. MTF also gives out essential information on which defaults or aberrations appear on an optical objective, and so enables to diagnose potential design or manufacturing issues on a production line or R&D prototype. Test benches and algorithms have been defined and developed in order to satisfy the growing needs in optical objectives qualification as the latter become more and more critical in their accuracy and quality specification. Many methods are used to evaluate the Modulating Transfer Function. Slit imaging and scanning on a camera, MTF evaluation thanks to wavefront measurement or imaging fixed slanted knife edge on the detector of the camera. All these methods have pros and cons, some lack in resolution, accuracy or don’t enable to compare simulated MTF curves with real measured data. These methods are firstly reminded in this paper.
  • Deconvolution in Optical Microscopy

    Deconvolution in Optical Microscopy

    Histochemical Journal 26, 687-694 (1994) REVIEW Deconvolution in 3-D optical microscopy PETER SHAW Department of Cell Biology, John Innes Centre, Colney Lane, Norwich NR 4 7UH, UK Received I0 January 1994 and in revised form 4 March 1994 Summary Fluorescent probes are becoming ever more widely used in the study of subcellular structure, and determination of their three-dimensional distributions has become very important. Confocal microscopy is now a common technique for overcoming the problem of oubof-focus flare in fluorescence imaging, but an alternative method uses digital image processing of conventional fluorescence images-a technique often termed 'deconvolution' or 'restoration'. This review attempts to explain image deconvolution in a non-technical manner. It is also applicable to 3-D confocal images, and can provide a further significant improvement in clarity and interpretability of such images. Some examples of the application of image deconvolution to both conventional and confocal fluorescence images are shown. Introduction to alleviate the resolution limits of optical imaging. The most obvious resolution limit is due to the wavelength Optical microscopy is centuries old and yet is still at the of the light used- about 0.25 lam in general. This limi- heart of much of modem biological research, particularly tation can clearly be overcome by non-conventional in cell biology. The reasons are not hard to find. Much optical imaging such as near-field microscopy; whether it of the current power of optical microscopy stems from can be exceeded in conventional microscopy ('super-res- the availability of an almost endless variety of fluorescent olution') has been very controversial (see e.g.
  • Pursuing the Diffraction Limit with Nano-LED Scanning Transmission Optical Microscopy

    Pursuing the Diffraction Limit with Nano-LED Scanning Transmission Optical Microscopy

    sensors Article Pursuing the Diffraction Limit with Nano-LED Scanning Transmission Optical Microscopy Sergio Moreno 1,* , Joan Canals 1 , Victor Moro 1, Nil Franch 1, Anna Vilà 1,2 , Albert Romano-Rodriguez 1,2 , Joan Daniel Prades 1,2, Daria D. Bezshlyakh 3, Andreas Waag 3, Katarzyna Kluczyk-Korch 4,5 , Matthias Auf der Maur 4 , Aldo Di Carlo 4,6 , Sigurd Krieger 7, Silvana Geleff 7 and Angel Diéguez 1,2 1 Electronic and Biomedical Engineering Department, University of Barcelona, 08028 Barcelona, Spain; [email protected] (J.C.); [email protected] (V.M.); [email protected] (N.F.); [email protected] (A.V.); [email protected] (A.R.-R.); [email protected] (J.D.P.); [email protected] (A.D.) 2 Institute for Nanoscience and Nanotechnology-IN2UB, University of Barcelona, 08028 Barcelona, Spain 3 Institute of Semiconductor Technology, Technische Universität Braunschweig, 38106 Braunschweig, Germany; [email protected] (D.D.B.); [email protected] (A.W.) 4 Department of Electronic Engineering, University of Rome “Tor Vergara”, 00133 Roma, Italy; [email protected] (K.K.-K.); [email protected] (M.A.d.M.); [email protected] (A.D.C.) 5 Faculty of Physics, University of Warsaw, 00-662 Warsaw, Poland 6 CNR-ISM, 00128 Rome, Italy 7 Department of Pathology, Medical University of Vienna, 1210 Wien, Austria; [email protected] (S.K.); [email protected] (S.G.) * Correspondence: [email protected] Abstract: Recent research into miniaturized illumination sources has prompted the development Citation: Moreno, S.; Canals, J.; of alternative microscopy techniques.
  • Superresolution Imaging Method Using Phase- Shifting Digital Lensless Fourier Holography

    Superresolution Imaging Method Using Phase- Shifting Digital Lensless Fourier Holography

    Superresolution imaging method using phase- shifting digital lensless Fourier holography Luis Granero 1, Vicente Micó 2* , Zeev Zalevsky 3, and Javier García 2 1 AIDO – Technological Institute of Optics, Color and Imaging, C/ Nicolás Copérnico 7, 46980, Paterna, Spain 2 Departamento de Óptica, Univ. Valencia, C/Dr. Moliner, 50, 46100 Burjassot, Spain 3 School of Engineering, Bar-Ilan University, Ramat-Gan, 52900 Israel *Corresponding author: [email protected] Abstract: A method which is useful for obtaining superresolved imaging in a digital lensless Fourier holographic configuration is presented. By placing a diffraction grating between the input object and the CCD recording device, additional high-order spatial-frequency content of the object spectrum is directed towards the CCD. Unlike other similar methods, the recovery of the different band pass images is performed by inserting a reference beam in on-axis mode and using phase-shifting method. This strategy provides advantages concerning the usage of the whole frequency plane as imaging plane. Thus, the method is no longer limited by the zero order term and the twin image. Finally, the whole process results in a synthetic aperture generation that expands up the system cutoff frequency and yields a superresolution effect. Experimental results validate our concepts for a resolution improvement factor of 3. 2009 Optical Society of America OCIS codes: (050.5080) Phase shift; (100.2000) Digital image processing; (070.0070) Fourier optics and signal processing; (090.1995) Digital holography; (100.6640) Superresolution. References and links 1. A. Bachl and A. W. Lukosz, “Experiments on superresolution imaging of a reduced object field,” J.
  • Bing Yan Phd 2018

    Bing Yan Phd 2018

    Bangor University DOCTOR OF PHILOSOPHY All-dielectric superlens and applications Yan, Bing Award date: 2018 Awarding institution: Bangor University Link to publication General rights Copyright and moral rights for the publications made accessible in the public portal are retained by the authors and/or other copyright owners and it is a condition of accessing publications that users recognise and abide by the legal requirements associated with these rights. • Users may download and print one copy of any publication from the public portal for the purpose of private study or research. • You may not further distribute the material or use it for any profit-making activity or commercial gain • You may freely distribute the URL identifying the publication in the public portal ? Take down policy If you believe that this document breaches copyright please contact us providing details, and we will remove access to the work immediately and investigate your claim. Download date: 09. Oct. 2021 ALL-DIELECTRIC SUPERLENS AND APPLICATIONS Bing Yan School of Electronic Engineering Bangor University A thesis submitted in partial fulfilment for the degree of Doctor of Philosophy May 2018 IV Acknowledgements First and foremost, I would like to express my sincere gratitude to my supervisor Dr Zengbo Wang for giving me this opportunity to work on such an exciting topic, and for his constant support during my entire PhD study and research. His guidance helped me in all time of research and writing of this thesis. I could not have imagined having a better advisor and mentor for my PhD study. During my PhD study, I have visited Swansea University and worked with many fascinating people for six months.
  • Measuring and Interpreting Point Spread Functions to Determine

    Measuring and Interpreting Point Spread Functions to Determine

    PROTOCOL Measuring and interpreting point spread functions to determine confocal microscope resolution and ensure quality control Richard W Cole1, Tushare Jinadasa2 & Claire M Brown2,3 1Wadsworth Center, New York State Department of Health, Albany, New York, USA. 2Department of Physiology, McGill University, Montreal, Quebec, Canada. 3Life Sciences Complex Imaging Facility, McGill University, Montreal, Quebec, Canada. Correspondence should be addressed to C.M.B. ([email protected]). Published online 10 November 2011; doi:10.1038/nprot.2011.407 This protocol outlines a procedure for collecting and analyzing point spread functions (PSFs). It describes how to prepare fluorescent microsphere samples, set up a confocal microscope to properly collect 3D confocal image data of the microspheres and perform PSF measurements. The analysis of the PSF is used to determine the resolution of the microscope and to identify any problems with the quality of the microscope’s images. The PSF geometry is used as an indicator to identify problems with the objective lens, confocal laser scanning components and other relay optics. Identification of possible causes of PSF abnormalities and solutions to improve microscope performance are provided. The microsphere sample preparation requires 2–3 h plus an overnight drying period. The microscope setup requires 2 h (1 h for laser warm up), whereas collecting and analyzing the PSF images require an additional 2–3 h. INTRODUCTION Rationale lens, and it is diffracted. The result is an image of the point source All rights reserved. The use of high-resolution confocal laser scanning microscopy that is much larger than the actual size of the object (compare Inc (CLSM) spans virtually all fields of the life sciences, as well as Fig.
  • Generalized Quantification of Three-Dimensional Resolution in Optical Diffraction Tomography Using the Projection of Maximal Spatial Bandwidths

    Generalized Quantification of Three-Dimensional Resolution in Optical Diffraction Tomography Using the Projection of Maximal Spatial Bandwidths

    Generalized quantification of three-dimensional resolution in optical diffraction tomography using the projection of maximal spatial bandwidths CHANSUK PARK,1,2 SEUNGWOO SHIN,1,2 AND YONGKEUN PARK1,2,3,* 1Department of Physics, Korea Advanced Institutes of Science and Technology (KAIST), Daejeon 34141, Republic of Korea 2KAIST Institute for Health Science and Technology, KAIST, Daejeon 34141, Republic of Korea 3Tomocube, Inc., Daejeon 34051, Republic of Korea *Corresponding author: [email protected] Optical diffraction tomography (ODT) is a three-dimensional (3D) quantitative phase imaging technique, which enables the reconstruction of the 3D refractive index (RI) distribution of a transparent sample. Due to its fast, non- invasive, and quantitative 3D imaging capability, ODT has emerged as one of the most powerful tools for various applications. However, the spatial resolution of ODT has only been quantified along the lateral and axial directions for limited conditions; it has not been investigated for arbitrary-oblique directions. In this paper, we systematically quantify the 3D spatial resolution of ODT by exploiting the spatial bandwidth of the reconstructed scattering potential. The 3D spatial resolution is calculated for various types of ODT systems, including the illumination-scanning, sample- rotation, and hybrid scanning-rotation methods. In particular, using the calculated 3D spatial resolution, we provide the spatial resolution as well as the arbitrary sliced angle. Furthermore, to validate the present method, the point spread function of an ODT system is experimentally obtained using the deconvolution of a 3D RI distribution of a microsphere and is compared with the calculated resolution. The present method for defining spatial resolution in ODT is directly applicable for various 3D microscopic techniques, providing a solid criterion for the accessible finest 3D structures.