DOCSLIB.ORG

Arxiv:1003.0154V1 [Physics.Atom-Ph] 28 Feb 2010 SWCNT Mode Lockers Have the Advantages Such As In- with Large Normal Cavity Dispersion8,9

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Arxiv:1003.0154V1 [Physics.Atom-Ph] 28 Feb 2010 SWCNT Mode Lockers Have the Advantages Such As In- with Large Normal Cavity Dispersion8,9 Graphene mode locked, wavelength-tunable, dissipative soliton fiber laser Han Zhang,1 Dingyuan Tang,1;∗ R. J. Knize,,2 Luming Zhao,1 Qiaoliang Bao,3 and Kian Ping Loh ,31 1School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore 639798 2Department of Physics, United States Air Force Academy, Colorado 80840, United States of America 3Department of Chemistry, National University of Singapore, Singapore 117543 ∗Corresponding author: [email protected], [email protected] a) (Dated: February 2010; Revised 22 October 2018) CONTENTS made. A wideband wavelength tunable erbium-doped fiber laser mode locked with SWCNTs was experimen- 2 I. Introduction 1 tally demonstrated . A. Nanotube Mode-Locked Fiber Laser1 B. Drawback of Nanotube Mode-Locker1 C. Soliton Fiber Laser1 B. Drawback of Nanotube Mode-Locker D. Graphene Mode-Locked Fiber Laser2 However, the broadband SWCNT mode locker suffers II. Experimental studies 2 intrinsic drawbacks: SWCNTs with a certain diameter only contribute to the saturable absorption of a particu- III. Conclusion 4 lar wavelength of light, and SWCNTs tend to form bun- dles that finish up as scattering sites. Therefore, coex- IV. Acknowledgement 4 istence of SWCNTs with different diameters introduces extra linear losses to the mode locker, making mode lock- V. Citations and References 4 ing of a laser difficult to achieve. In this letter we show that these drawbacks could be circumvented if graphene is used as a broadband saturable absorber. Implementing I. INTRODUCTION graphene mode locking in a specially designed erbium- doped fiber laser, we demonstrated the first wide range Atomic layer graphene possesses wavelength- (1570nm- 1600nm) wavelength tunable dissipative soliton insensitive ultrafast saturable absorption, which fiber laser. can be exploited as a "full-band" mode locker. Taking advantage of the wide band saturable absorption of the graphene, we demonstrate experimentally that C. Soliton Fiber Laser wide range (1570 nm - 1600nm) continuous wavelength tunable dissipative solitons could be formed in an erbium Soliton operation of mode locked fiber lasers has been doped fiber laser mode locked with few atomic layer extensively investigated previously. Conventionally, the graphene. study on soliton operation of fiber lasers was focused on lasers with anomalous cavity dispersion, where a soliton is formed due to the natural balance between the anoma- A. Nanotube Mode-Locked Fiber Laser lous cavity dispersion and fiber nonlinear optical Kerr effect, and the dynamics of the formed solitons is gov- Recently, passive mode locking of fiber lasers with sin- erned by the nonlinear Schrodinger equation. Recently, gle walled carbon nanotubes (SWCNTs) has attracted it was further shown both experimentally and theoreti- 1{7 considerable attention . It has been shown that cally that a soliton could even be formed in fiber lasers arXiv:1003.0154v1 [physics.atom-ph] 28 Feb 2010 SWCNT mode lockers have the advantages such as in- with large normal cavity dispersion8,9. Formation of soli- trinsically ultrafast recovery time, large saturable ab- tons in the normal dispersion fiber lasers is a result of sorption, easy to fabricate, and low cost. In particu- the mutual nonlinear interaction among the normal cav- lar, as SWCNTs are direct-bandgap materials with a gap ity dispersion, fiber Kerr nonlinearity, and the effective that depends on the nano-tubes' diameter and chiral- laser gain bandwidth filtering? , and the dynamics of the ity, through mixing SWCNTs with different diameters, formed solitons is governed by the complex Ginzburg- a broadband saturable absorption mode locker could be Landau equation (GLE). A soliton whose dynamics is governed by the GLE is also known as a dissipative soli- ton. Comparing with the operation of the conventional soliton fiber lasers, where sub-picosecond optical pulses a)Electronic mail: http://www3.ntu.edu.sg/home2006/zhan0174/ could be routinely generated but the pulse energy is lim- 2 ited at the level of tens of pico-joules, the operation of a dissipative soliton fiber laser can naturally generate large energy strongly chirped optical pulses . Due to its strongly chirped feature, a dissipative soliton can be eas- ily amplified and compressed10,11. Consequently, large energy ultrashort pulses can be generated. However, be- cause a dissipative soliton fiber laser is operating in the large positive cavity dispersion regime, self-started mode locking in the laser is much more difficult to achieve than in the conventional soliton fiber lasers. D. Graphene Mode-Locked Fiber Laser Unlike the conventional semiconductor saturable ab- (a) sorbers, the energy band diagram of graphene has zero bandgap and a linear dispersion relation12. These unique energy band properties combined with the Pauli block- ing principle renders graphene a full band ultrafast sat- urable absorber13. Fig. 1a shows a schematic illustra- tion of the energy band structure and photon absorp- tion of graphene. Li et al14] had experimentally shown that atomic layer graphene could absorb a considerable amount of infrared light without any bandwidth limita- tion. In previous papers we have also experimentally shown passive mode locking of an erbium-doped fiber laser? and a solid-state Nd:YAG ceramic laser16 respec- tively using graphene as a mode locker. It is to point out that determined by its unique energy band structure the saturation intensity of graphene is wavelength sen- (b) sitive. We had experimentally measured the saturation intensity of graphene at 1.06 µm and 1.56 µm, respec- −2 FIG. 1. (a) Schematic of graphene's energy band structure tively. It varies from 0.87 MW* cm at 1.06?m to 0.71 and photon absorption. (b) Schematic of the dissipative soli- −2 13,15,16 MW*cm at 1.56 µm . ton fiber laser. WDM denotes: wavelength division multi- plexer, EDF denotes erbium-doped fiber, PC denotes polar- ization controller, and DCF denotes dispersion compensation II. EXPERIMENTAL STUDIES fiber. To exploit the wideband saturable absorption of graphene for wavelength tunable soliton generation, we (PC) was used to adjust the cavity birefringence. The further specially designed an erbium-doped dissipative laser was pumped by a high power Fiber Raman Laser of soliton fiber laser. We note that dissipative soliton op- wavelength 1480 nm. The graphene saturable absorber eration of fiber lasers mode locked with SWCNTs was was inserted in the cavity through transferring a piece reported by Kieu and Wise7, and Z. Sun et al. However, of free standing few layers graphene film onto the end dissipative soliton operation of fiber lasers mode locked facet of a fiber pigtail via the Van der Walls force. De- with atomic layer graphene has not been demonstrated. tails on the graphene preparation and graphene saturable Moreover, wavelength tunable dissipative soliton lasers absorber characterization were reported in13. The main were never reported. Our fiber laser is schematically difference of the current fiber laser from that reported shown in Fig. 1b. The laser cavity is made of a piece in15 is that normal dispersion EDF instead of anomalous of 5.0 m erbium-doped fiber (EDF) with erbium-doping dispersion EDF was employed as the gain medium. To concentration of 2280 ppm and a group velocity disper- assure large net positive cavity dispersion we also added sion (GVD) parameter of -32 (ps/nm)/km, a total length a long piece of DCF to the cavity. In addition, we delib- of 9.0m single mode fiber (SMF) with GVD parameter of erately introduced large cavity birefringence in the laser, 18 (ps/nm)/km from optical components, and 118m dis- which strengthens the effect of the artificial birefringence persion compensation fiber (DCF) with GVD parameter filter formed in the cavity17,18. of about -2 (ps/nm)/km. A polarization independent Due to the saturable absorption of graphene, mode isolator was used to force the unidirectional operation locking of the laser was always achieved. As the total of the ring, and an intra-cavity polarization controller cavity dispersion is 0.3047ps2, the mode locked pulse 3 was shaped into a dissipative soliton. Fig. 2 shows a typical dissipative soliton operation state of the laser. - 1 0 ) Fig. 2a is the optical spectrum of the soliton. It has m B - 2 0 the characteristic sharp steep spectral edges of the dissi- d ( 8{10 pative solitons . The 3dB spectral bandwidth is 7.2 y t i nm. Using a 50 GHz high-speed oscilloscope (Tektronix s - 3 0 n e CSA 8000) together with a 45 GHz photo-detector (New t n I Focus 1014), we measured the pulse profile of the dissipa- - 4 0 m tive solitons, as shown in Fig. 2b. The pulse width is 49 u r t ps. The time-bandwidth product of the pulses is 44.3, c - 5 0 e indicating that they are strongly chirped. Fig. 2c shows p the oscilloscope trace of the mode locked pulse train. The S 1 5 7 5 1 5 8 0 1 5 8 5 1 5 9 0 1 5 9 5 W a v e l e n g t h ( n m ) pulse-to-pulse separation is 660 ns, which matches the cavity roundtrip time. In our experiment we had also (a) measured the mode locked pulses with a commercial au- tocorrelator and confirmed that no fine structures within the pulses. 1 . 0 E x p e r i m e n t a l d a t a In weakly birefringent cavity fiber lasers, where the ) 2 S e c h F i t t i n g s t cavity birefringence induced artificial birefringence filter i 0 . 8 n u has a large bandwidth; the filtering effect of the bire- . b 0 . 6 fringence filter could normally be ignored. In our laser, r a ( the effect of cavity artificial birefringence filter no longer y t 0 . 4 i can be ignored, instead it together with the erbium fiber s n e determines the effective laser gain and gain profile.
Load more

Recommended publications
  • Conventional Soliton and Noise-Like Pulse Generated in an Er-Doped Fiber Laser with Carbon Nanotube Saturable Absorbers
    applied sciences Article Conventional Soliton and Noise-Like Pulse Generated in an Er-Doped Fiber Laser with Carbon Nanotube Saturable Absorbers Zikai Dong 1, Jinrong Tian 1, Runlai Li 2 , Youshuo Cui 1, Wenhai Zhang 3 and Yanrong Song 1,* 1 College of Applied Sciences, Beijing University of Technology, Beijing 100124, China; [email protected] (Z.D.); [email protected] (J.T.); [email protected] (Y.C.) 2 Department of Chemistry, National University of Singapore, Singapore 637551, Singapore; [email protected] 3 College of Environment and Energy Engineering, Beijing University of Technology, Beijing 100124, China; [email protected] * Correspondence: [email protected] Received: 6 July 2020; Accepted: 27 July 2020; Published: 11 August 2020 Featured Application: Multi-functional ultrafast laser sources, conventional soliton and noise-like pulse laser system, nanomaterial saturable absorption effect test system. Abstract: Conventional soliton (CS) and noise-like pulse (NLP) are two different kinds of pulse regimes in ultrafast fiber lasers, which have many intense applications. In this article, we experimentally demonstrate that the pulse regime of an Er-doped fiber laser could be converted between conventional soliton and noise-like pulse by using fast response saturable absorbers (SA) made from different layers of single-wall carbon nanotubes (CNT). For the monolayer (ML) single-wall CNT-SA, CS with pulse duration of 439 fs at 1560 nm is achieved while for the bilayer (BL) single-wall CNT, NLP at 1560 nm with a 1.75 ps spike and a 98 ps pedestal is obtained. The transition mechanism from CS to NLP is investigated by analyzing the optical characteristics of ML and BL single-wall CNT.
    [Show full text]
  • Real-Time Observation of Dissipative Soliton Formation in Nonlinear Polarization Rotation Mode- Locked fibre Lasers
    ARTICLE DOI: 10.1038/s42005-018-0022-7 OPEN Real-time observation of dissipative soliton formation in nonlinear polarization rotation mode- locked fibre lasers Junsong Peng1, Mariia Sorokina2, Srikanth Sugavanam2, Nikita Tarasov2,3, Dmitry V. Churkin3, 1234567890():,; Sergei K. Turitsyn2,3 & Heping Zeng1 Formation of coherent structures and patterns from unstable uniform state or noise is a fundamental physical phenomenon that occurs in various areas of science ranging from biology to astrophysics. Understanding of the underlying mechanisms of such processes can both improve our general interdisciplinary knowledge about complex nonlinear systems and lead to new practical engineering techniques. Modern optics with its high precision mea- surements offers excellent test-beds for studying complex nonlinear dynamics, though capturing transient rapid formation of optical solitons is technically challenging. Here we unveil the build-up of dissipative soliton in mode-locked fibre lasers using dispersive Fourier transform to measure spectral dynamics and employing autocorrelation analysis to investi- gate temporal evolution. Numerical simulations corroborate experimental observations, and indicate an underlying universality in the pulse formation. Statistical analysis identifies cor- relations and dependencies during the build-up phase. Our study may open up possibilities for real-time observation of various nonlinear structures in photonic systems. 1 State Key Laboratory of Precision Spectroscopy, East China Normal University, 200062 Shanghai,
    [Show full text]
  • Stochastic and Higher-Order Effects on Exploding Pulses
    Article Stochastic and Higher-Order Effects on Exploding Pulses Orazio Descalzi * and Carlos Cartes Complex Systems Group, Facultad de Ingeniería y Ciencias Aplicadas, Universidad de los Andes, Av. Mons. Álvaro del Portillo 12.455, Las Condes, Santiago 7620001, Chile; [email protected] * Correspondence: [email protected] Received: 27 June 2017; Accepted: 22 July 2017; Published: 30 August 2017 Abstract: The influence of additive noise, multiplicative noise, and higher-order effects on exploding solitons in the framework of the prototype complex cubic-quintic Ginzburg-Landau equation is studied. Transitions from explosions to filling-in to the noisy spatially homogeneous finite amplitude solution, collapse (zero solution), and periodic exploding dissipative solitons are reported. Keywords: exploding solitons; Ginzburg-Landau equation; mode-locked fiber lasers 1. Introduction Soliton explosions, fascinating nonlinear phenomena in dissipative systems, have been observed in at least three key experiments. As has been reported by Cundiff et al. [1], a mode-locked laser using a Ti:Sapphire crystal can produce intermittent explosions. More recently, a different medium for explosions was reported by Broderick et al., namely, a passively mode-locked fibre laser [2]. In 2016, Liu et al. showed that in an ultrafast fiber laser, the exploding behavior could operate in a sustained but periodic mode called “successive soliton explosions” [3]. Almost all parts of these exploding objects are unstable, but nevertheless they remain localized. Localized structures in systems far from equilibrium are the result of a delicate balance between injection and dissipation of energy, nonlinearity and dispersion (compare [4] for a recent exposition of the subject). This fact leads to a generalization of the well known conservative soliton to a dissipative soliton DS (Akhmediev et al.
    [Show full text]
  • Dissipative Soliton Interactions Inside a Fiber Laser Cavity
    Optical Fiber Technology 11 (2005) 209–228 www.elsevier.com/locate/yofte Invited paper Dissipative soliton interactions inside a fiber laser cavity N. Akhmediev a,∗, J.M. Soto-Crespo b, M. Grapinet c, Ph. Grelu c a Optical Sciences Group, RSPhysSE, ANU, ACT 0200, Australia b Instituto de Óptica, CSIC, Serrano 121, 28006 Madrid, Spain c Laboratoire de Physique de l’Université de Bourgogne, Unité Mixte de Recherche 5027 du Centre National de Recherche Scientifique, B.P. 47870, 21078 Dijon, France Received 9 December 2004 Available online 22 April 2005 Abstract We report our recent numerical and experimental observations of dissipative soliton interactions inside a fiber laser cavity. A bound state, formed from two pulses, may have a group velocity which differs from that of a single soliton. As a result, they can collide inside the cavity. This results in a variety of outcomes. Numerical simulations are based either on a continuous model or on a parameter-managed model of the cubic-quintic Ginzburg–Landau equation. Each of the models pro- vides explanations for our experimental observations. 2005 Elsevier Inc. All rights reserved. Keywords: Soliton 1. Introduction Soliton interaction is one of the most exciting areas of research in nonlinear dynam- ics. The unusual features of collisions in systems described by the Korteweg–de Vries (KdV) equation [1] were the starting point of these intensive studies. It was discovered that solitons in this system pass through each other without changing their amplitude and * Corresponding author. E-mail address: [email protected] (N. Akhmediev). 1068-5200/$ – see front matter 2005 Elsevier Inc.
    [Show full text]
  • Twenty-Five Years of Dissipative Solitons
    Twenty-Five Years of Dissipative Solitons Ivan C. Christova) and Zongxin Yub) School of Mechanical Engineering, Purdue University, West Lafayette, Indiana 47907, USA Abstract. In 1995, C. I. Christov and M. G. Velarde introduced the concept of a dissipative soliton in a long-wave thin-film equation [Physica D 86, 323–347]. In the 25 years since, the subject has blossomed to include many related phenomena. The focus of this short note is to survey the conceptual influence of the concept of a “production-dissipation (input-output) energy balance” that they identified. Our recent results on nonlinear periodic waves as dissipative solitons (in a model equation for a ferrofluid interface in a parallel-flow rectangular geometry subject to an inhomogeneous magnetic field) have shown that the classical concept also applies to nonlocalized (specifically, spatially periodic) nonlinear coherent structures. Thus, we revisit the so-called KdV-KSV equation studied by C. I. Christov and M. G. Velarde to demonstrate that it also possesses spatially periodic dissipative soliton solutions. These coherent structures arise when the linearly unstable flat film state evolves to sufficiently large amplitude. The linear instability is then arrested when the nonlinearity saturates, leading to permanent traveling waves. Although the two model equations considered in this short note feature the same prototypical linear long-wave instability mechanism, along with similar linear dispersion, their nonlinearities are fundamentally different. These nonlinear terms set the shape and eventual dynamics of the nonlinear periodic waves. Intriguingly, the nonintegrable equations discussed in this note also exhibit multiperiodic nonlinear wave solutions, akin to the polycnoidal waves discussed by J.
    [Show full text]
  • Bilkent-Graduate Catalog 0.Pdf
    ISBN: 978-605-9788-11-3 bilkent.edu.tr ACADEMIC OFFICERS OF THE UNIVERSITY Ali Doğramacı, Chairman of the Board of Trustees and President of the University CENTRAL ADMINISTRATION DEANS OF FACULTIES Abdullah Atalar, Rector (Chancellor) Ayhan Altıntaş, Faculty of Art, Design, and Architecture (Acting) Adnan Akay, Vice Rector - Provost Mehmet Baray, Faculty of Education (Acting) Kürşat Aydoğan, Vice Rector Ülkü Gürler, Faculty of Business Administration (Acting) Orhan Aytür, Vice Rector Ezhan Karaşan, Faculty of Engineering Cevdet Aykanat, Associate Provost Hitay Özbay, Faculty of Humanities and Letters (Acting) Hitay Özbay, Associate Provost Tayfun Özçelik, Faculty of Science Özgür Ulusoy Associate Provost Turgut Tan, Faculty of Law Erinç Yeldan, Faculty of Economics, Administrative, and Social Sciences (Acting) GRADUATE SCHOOL DIRECTORS Alipaşa Ayas, Graduate School of Education [email protected] Halime Demirkan, Graduate School of Economics and Social Sciences [email protected] Ezhan Karaşan, Graduate School of Engineering and Science [email protected] DEPARTMENT CHAIRS and PROGRAM DIRECTORS Michelle Adams, Neuroscience [email protected] Adnan Akay, Mechanical Engineering [email protected] M. Selim Aktürk, Industrial Engineering [email protected] Orhan Arıkan, Electrical and Electronics Engineering [email protected] Fatihcan Atay, Mathematics [email protected] Pınar Bilgin, Political Science and Public Administration [email protected] Hilmi Volkan Demir, Materials Science and Nanotechnology [email protected] Oğuz Gülseren, Physics [email protected] Ahmet Gürata, Communication and Design [email protected] Meltem Gürel, Architecture [email protected] Refet Gürkaynak, Economics [email protected] Ülkü Gürler, Business Administration (Acting) [email protected] H.
    [Show full text]
  • Breathing Dissipative Solitons in Optical Microresonators
    ARTICLE DOI: 10.1038/s41467-017-00719-w OPEN Breathing dissipative solitons in optical microresonators E. Lucas1, M. Karpov1, H. Guo1, M.L. Gorodetsky2,3 & T.J. Kippenberg1 Dissipative solitons are self-localised structures resulting from the double balance of dis- persion by nonlinearity and dissipation by a driving force arising in numerous systems. In Kerr-nonlinear optical resonators, temporal solitons permit the formation of light pulses in the cavity and the generation of coherent optical frequency combs. Apart from shape-invariant stationary solitons, these systems can support breathing dissipative solitons exhibiting a periodic oscillatory behaviour. Here, we generate and study single and multiple breathing solitons in coherently driven microresonators. We present a deterministic route to induce soliton breathing, allowing a detailed exploration of the breathing dynamics in two micro- resonator platforms. We measure the relation between the breathing frequency and two control parameters—pump laser power and effective-detuning—and observe transitions to higher periodicity, irregular oscillations and switching, in agreement with numerical predic- tions. Using a fast detection, we directly observe the spatiotemporal dynamics of individual solitons, which provides evidence of breather synchronisation. 1 IPHYS, École Polytechnique Fédérale de Lausanne (EPFL), CH-1015 Lausanne, Switzerland. 2 Russian Quantum Centre, Skolkovo 143025, Russia. 3 Faculty of Physics, M.V. Lomonosov Moscow State University, 119991 Moscow, Russia. E. Lucas and M. Karpov contributed equally to this work. Correspondence and requests for materials should be addressed to T.J.K. (email: tobias.kippenberg@epfl.ch) NATURE COMMUNICATIONS | 8: 736 | DOI: 10.1038/s41467-017-00719-w | www.nature.com/naturecommunications 1 ARTICLE NATURE COMMUNICATIONS | DOI: 10.1038/s41467-017-00719-w issipative solitons are localised structures, occurring in a dependence on the pump power.
    [Show full text]
  • Dissipative Soliton Comb
    Dissipative soliton comb Evgeniy V. Podivilov1,2, Denis S. Kharenko1,2, Anastasia E. Bednyakova2,3, Mikhail P. Fedoruk2,3, Sergey A. Babin1,2* 1 Institute of Automation and Electrometry, SB RAS, Novosibirsk 630090, Russia 2Novosibirsk State University, Novosibirsk 630090, Russia 3Institute of Computational Technologies, SB RAS, Novosibirsk 630090, Russia *Corresponding author: [email protected] Dissipative solitons are stable localized coherent structures with linear frequency chirp generated in normal-dispersion mode-locked lasers. The soliton energy in fiber lasers is limited by the Raman effect, but implementation of intracavity feedback for the Stokes wave enables synchronous generation of a coherent Raman dissipative soliton. Here we demonstrate a new approach for generating chirped pulses at new wavelengths by mixing in a highly-nonlinear fiber of two frequency-shifted dissipative solitons, as well as cascaded generation of their clones forming a “dissipative soliton comb” in the frequency domain. We observed up to eight equidistant components in a 400-nm interval demonstrating compressibility from ~10 ps to ~300 fs. This approach, being different from traditional frequency combs, can inspire new developments in fundamental science and applications. It is well known that the phase synchronization of laser modes (so-called mode locking) forms a pulse train with a period equal to the inverse mode spacing and duration equal to the inverse gain bandwidth [1]. In the case of a broadband gain medium, the mode-locked laser can generate ultrashort pulses while its broad spectrum consisting of equidistant frequencies represents so- called “frequency comb” [2,3]. In Ti:sapphire lasers, the comb width can reach one octave [4].
    [Show full text]
  • Soliton Molecules and Multisoliton States in Ultrafast Fibre Lasers: Intrinsic Complexes in Dissipative Systems
    applied sciences Review Soliton Molecules and Multisoliton States in Ultrafast Fibre Lasers: Intrinsic Complexes in Dissipative Systems Lili Gui 1,*, Pan Wang 2, Yihang Ding 2, Kangjun Zhao 2, Chengying Bao 3, Xiaosheng Xiao 2 and Changxi Yang 2,* 1 4th Physics Institute and Research Center SCoPE, University of Stuttgart, Pfaffenwaldring 57, 70569 Stuttgart, Germany 2 State Key Laboratory of Precision Measurement Technology and Instruments, Department of Precision Instruments, Tsinghua University, Beijing 100084, China; [email protected] (P.W.); [email protected] (Y.D.); [email protected] (K.Z.); [email protected] (X.X.) 3 Watson Laboratory of Applied Physics, California Institute of Technology, Pasadena, CA 91125, USA; [email protected] * Correspondence: [email protected] (L.G.); [email protected] (C.Y.); Tel.: +86-10-6277-2824 (C.Y.) Received: 14 December 2017; Accepted: 23 January 2018; Published: 29 January 2018 Featured Application: High-capacity telecommunication, advanced time-resolved spectroscopy, self-organization and chaos in dissipative systems. Abstract: Benefiting from ultrafast temporal resolution, broadband spectral bandwidth, as well as high peak power, passively mode-locked fibre lasers have attracted growing interest and exhibited great potential from fundamental sciences to industrial and military applications. As a nonlinear system containing complex interactions from gain, loss, nonlinearity, dispersion, etc., ultrafast fibre lasers deliver not only conventional single soliton but also soliton bunching with different types. In analogy to molecules consisting of several atoms in chemistry, soliton molecules (in other words, bound solitons) in fibre lasers are of vital importance for in-depth understanding of the nonlinear interaction mechanism and further exploration for high-capacity fibre-optic communications.
    [Show full text]
  • A Pittetd-Thesis Sample
    ALL-FIBER MODE-LOCKED ULTRAFAST THULIUM-DOPED FIBER LASERS AT 2µm by QingQing Wang B.S., Physics, University of Science and Technology of China, 2005 M.S., Physics, University of Pittsburgh, 2008 Submitted to the Graduate Faculty of the Department of Electrical and Computer Engineering Swanson School of Engineering in partial fulfillment of the requirements for the degree of Doctor of Philosophy University of Pittsburgh 2014 UNIVERSITY OF PITTSBURGH SWANSON SCHOOL OF ENGINEERING This dissertation was presented by QingQing Wang It was defended on July 16 2014 and approved by Kevin P. Chen, Ph.D., Associate Professor, Department of Electrical and Computer Engineering William Stanchina, Ph.D., Professor, Department of Electrical and Computer Engineering Mahmoud El Nokali, Ph.D., Associate Professor, Department of Electrical and Computer Engineering Guangyong Li, Ph.D., Associate Professor, Department of Electrical and Computer Engineering Karl Harris, Ph.D., Penn State Electro-Optics Center Dissertation Director: Kevin P. Chen, Ph.D., Associate Professor, Department of Electrical and Computer Engineering ii ALL-FIBER MODE-LOCKED ULTRAFAST THULIUM-DOPED FIBER LASERS AT 2µm QingQing Wang, PhD University of Pittsburgh, 2014 In this work, we demonstrate three original all-fiber ring configurations of passively mode- locked Thulium-doped fiber(TDF) lasers operated around 2µm wavelength for which the us- age of free-space optics components is minimized. Different mode-locking techniques/materi- als e.g. nonlinear polarization evolution (NPE), graphene-based saturable asbsorbers(GSAs) and single-wall carbon nanotubes (SWCNTs) are developed and used to passively mode lock TDF laser and produce ultrashort pulses at 2µm. Also to achieve higher pulse energy di- rectly from a fiber oscillator, the net intra-cavity dispersion is managed by the introducing of normal dispersion fiber(NDF) at 2µm into the fiber cavity.
    [Show full text]
  • On Boussinesq's Paradigm in Nonlinear Wave Propagation
    C. R. Mecanique 335 (2007) 521–535 http://france.elsevier.com/direct/CRAS2B/ Boussinesq equation, elasticity, beams, plates On Boussinesq’s paradigm in nonlinear wave propagation Christo I. Christov a, Gérard A. Maugin b,∗, Alexey V. Porubov c a Department of Mathematics, University of Louisiana at Lafayette, P.O. Box 1010, Lafayette, LA 70504-1010, USA b Université Pierre et Marie Curie, Institut Jean le Rond d’Alembert, UMR 7190, case 162, 4, place Jussieu, 75252 Paris cedex 05, France c Institute for Problems in Mechanical Engineering, R.A.S., V.O., Bolshoy avenue 61, Saint-Petersburg 199178, Russia Received 11 December 2006; accepted after revision 14 March 2007 Available online 14 September 2007 Abstract Boussinesq’s original derivation of his celebrated equation for surface waves on a fluid layer opened up new horizons that were to yield the concept of the soliton. The present contribution concerns the set of Boussinesq-like equations under the general title of ‘Boussinesq’s paradigm’. These are true bi-directional wave equations occurring in many physical instances and sharing analogous properties. The emphasis is placed: (i) on generalized Boussinesq systems that involve higher-order linear dispersion through either additional space derivatives or additional wave operators (so-called double-dispersion equations); and (ii) on the ‘mechanics’ of the most representative localized nonlinear wave solutions. Dissipative cases and two-dimensional generalizations are also considered. To cite this article: C.I. Christov et al., C. R. Mecanique 335 (2007). © 2007 Académie des sciences. Published by Elsevier Masson SAS. All rights reserved. Résumé Sur la paradigme de Boussinesq pour la propagation d’ondes non linéaires.
    [Show full text]
  • Dual-Wavelength Dissipative Solitons in an Anomalous-Dispersion-Cavity
    Nanophotonics 2020; 9(8): 2361–2366 Research article Yufeng Song, Guodong Shao, Luming Zhao, Deyuan Shen, Han Zhang and Dingyuan Tang* Dual-wavelength dissipative solitons in an anomalous-dispersion-cavity fiber laser https://doi.org/10.1515/nanoph-2019-0374 laser is through multi-wavelength mode locking. Experi- Received September 19, 2019; revised November 5, 2019; accepted mentally, multi-wavelength mode locking was achieved November 17, 2019 in actively mode-locked fiber lasers [7, 8]. However, due to their low energy, the mode-locked pulses were difficult Abstract: We report on the experimental observation of to be shaped into solitons. Multi-wavelength solitons were dual-wavelength dissipative soliton operation of a fiber first obtained in a passively mode-locked fiber laser with laser with net anomalous cavity dispersion. Different from the nonlinear polarization rotation (NPR) technique [8, 9]. the dual- or multi-wavelength soliton operation of fiber With the development of mode-locking technology, dual- lasers where mode locking is used to initiate soliton for- or multi-wavelength solitons have also been observed mation, no mode locking occurs in our fiber laser. Instead, in fiber lasers passively model-locked by real saturable soliton formation is through the dissipative mechanism absorbers [10–13]. Zhang et al. reported multi-wavelength caused by the effective gain bandwidth limitation. Either dissipative soliton generation in a semiconductor satura- dual-wavelength scalar, or vector, or induced dissipative ble absorber mirror (SESAM) mode-locked fiber laser [11]. solitons are experimentally obtained. Their robustness is A switchable dual-wavelength frequency comb fiber laser experimentally confirmed. passively mode-locked by carbon nanotubes was reported Keywords: pulse propagation and temporal solitons; non- by Zhao et al.
    [Show full text]