ME8792 POWER PLANT ENGINEERING

Dr.V.Tamil Selvi , Prof.& Head , RMDEEE Ms.Aileen Sonia Dhas , AP/RMDEEE UNIT IV POWER FROM RENEWABLE • Hydro Plants Classification Typical Layout and associated components including Turbines. • Principle, Construction and working of » Wind » Tidal » Solar Photo Voltaic (SPV) » Solar Thermal » Geo Thermal » Biogas » Cell power systems. HYDROELECTRIC POWER Hydro electric power

Hydroelectricity is the term referring to electricity generated by ; the production of electrical power through the use of the gravitational force of falling or flowing water • https://youtu.be/JC-2HIUQBjo • https://youtu.be/Uhjhufhg3Xk • https://youtu.be/q8HmRLCgDAI

Classification Of Hydro-Electric Power Plants 1.Classification According To The Availability Of head –Low head power plant –Medium head power plant –High head power plant 2.Classification according to the nature of load  Base load plant  Peak load plant 3. Classification according to the quantity of water available  Run-off river plant without pondage Run-of-the-river power plants may have no water storage at all or a limited amount of storage, in which case the storage reservoir is referred to as pondage. A plant without pondage is subject to seasonal riverflows, thus the plant will operate as an intermittent energy source.

 Run-off river plant with pondage This type of plant is used to increase the capacity of pond.The pond is used as a storage water of hydro electric power plant.Increased the pond size means more water is available in the plant,so such type of hydro electric power plant is used fluctuating load period depending on the size of pondage.. Such type of plant is suitable for both base load or peak load period.During high flow period,this plant is suitable for base load and lean flow period it may be used to supply peak loads only. During high flood period,one thing should keep in mind that flood should not raise tail-race water level.Such types of power plant save conservation of coal.  Pumped storage plants/Reservoir Powerplants Most hydroelectric power plant in the world is reservoir power plant. In this type of plant, water is stored behind the (and water is available throughout the second reservoir constructed near the water outflow from turbine)year even in dry season. This type of power plant is very efficient and it is used both base and peak load period as per requirement.most importantly,it can also take a part of load curve in grid system. Conventional ()

• Most hydroelectric power comes from the potential energy of dammed water driving a water turbine and generator

• The power extracted from the water depends on the volume and on the difference in height between the source and the water's outflow .This height difference is called the head.

• The amount of potential energy in water is proportional to the head

• A large pipe (the "penstock") delivers water to the turbine Run-of-the-river

• Run-of-the-river hydroelectric stations are those with small or no reservoir capacity, so that the water coming from upstream must be used for generation at that moment, or must be allowed to bypass the dam.

12 Layout of Hydroelectric Power Plant

Working of

• Dam: controls the flow of water and creates a reservoir of water above for energy use when needed • Penstock: pipe channeling water from the dam to the turbines • Turbines: large blades attached to a cylinder that move when the water pushes against it • Generator: parts connected to the turbines that create the electricity by moving large magnets • Inductor: changes the form of electricity to one that can be used • Transmission Lines: transport energy to places that need it Components of hydro-electric Power Plant . Water Reservoir . Dam . Spillway- are structures constructed toprovide safe release offlood waters froma dam toa downstream. . Trash rack- water from dam or from canal is provided with trash rack to prevent the entry of debris which might damage the wicket gates and turbine runners orchoke up the nozzles of the impulse turbine . Forebay- serves as temporary regulating reservoir which is used to store water when the load on the plant is reduced. . Water Tunnel- carries water from the reservoir to surge tank. . Canals- a water channel required to the ater to the powerhouse . Penstock . Pipeline laid between surge tank and prime mover is known as penstick . Surge Tank . Small reservoir in which the water levelraises or falls to reduce the pressure c\variation so that the steady flowof water is supplied toallloads. . Water Turbine . Water through the penstock ,enters into the turbine through the inlet valve. . Draft tube . Connected at the outlet of the waterturbine . Tail race . Water channel or cut and cover conduit. . Powerhouse . Turbine,generator,control panels,transformers,auxilliary equipments,etc are kept. • Classification based on the power developed by the plant – Large hydro (>100MW) – Medium-hydro(15-100MW) – Smallhydro(1-14 MW) – Mini-hydro (> 100kW) – Micro-hydra(5kW upto 100kW) – Pico-hydro(few hundred watts upto 5kW) spillway Surge tank

Low Head Hydroelectrical Generators

Low head: Propellor type Turbines

Power = Change in Potential Energy per Unit time

= weight* Vertical drop/time

Energy = Power*time Moderate Head Hydro

Head: height difference Between water level in Reservoir and water Level entering turbine

Head= height in potential Energy equation

Penstock: tube water flows Through High Head Hydro • A micro-hydro facility in Vietnam

27 Pico in Mondulkiri, Cambodia 28 Francis turbine

Turbine used for moderate Head hydroelectrical power statiosn Water Flow in a Francis Turbine

Left: relative to turbine blades Right: true water path Reaction turbines

• Reaction turbines are acted on by water, which changes pressure as it moves through the turbine and gives up its energy • They must be encased to contain the water pressure (or suction), or they must be fully submerged in the water flow • Newton's third law describes the transfer of energy for reaction turbines. Most water turbines in use are reaction turbines and are used in low (<30m/98 ft) and medium (30-300m/98–984 ft)head applications. In reaction turbine pressure drop occurs in both fixed and moving blades.

31 Impulse turbines

• Impulse turbines change the velocity of a water jet. The jet pushes on the turbine's curved blades which changes the direction of the flow • The resulting change in momentum (impulse) causes a force on the turbine blades. Since the turbine is spinning, the force acts through a distance (work) and the diverted water flow is left with diminished energy • Prior to hitting the turbine blades, the water's pressure (potential energy) is converted to kinetic energy by a nozzle and focused on the turbine • No pressure change occurs at the turbine blades, and the turbine doesn't require a housing for operation • Newton's second law describes the transfer of energy for impulse turbines • Impulse turbines are most often used in very high (>300m/984 ft) head applications

32 Pelton Water Wheel

Used for high head applications: (above 250 meters) Are impulse turbines.

Francis and Propeller type turbine Are reaction turbines.

Reaction turbines: run submerged.

Impulse turbines: run in normal air Types of water turbines

Various types of water turbine runners. From left to right: Pelton Wheel, two types of Francis Turbine and Kaplan Turbine

34 WIND ENERGY RESOURCES Characteristics of Wind Energy a. Do not pollute the atmosphere b. Fuel provision and transport are not required in wind-power systems c. Is a renewable source of energy d. Wind energy when produced on small sclae is cheapbut it is competitive with conventionalpower generating system when produced on a large scale. Principle of Wind Energy Conversion Types of Wind Energy System Based on the force exerted on blades • Lift type wind turbine – A high speed turbine depends onlift forces tomove the blades of the wind turbine. The linear speed of the blades is usually several times higher than the wind speed. The torque oflift force islow as compared to the drag type • Drag type wind turbine – Low speed turbines are slower than the wind. They are mainly driven by the drag force. The torque at the rotor shaft is relatively high. Based on the axis of rotation of the rotor – Horizontal – axis wind machines – Vertical-axis wind machines

Components of Wind Turbine

• Wind turbine • Nascelle(gearbox,lowand high speed shafts,generator controller and brake) • Rotor i.e the assembly of blades • Hub and shaft • Transmission system • • Yaw control system • Storage • Energy converters • Tower to support the rotor system GENERATING

2 Attach a voltage probe

Attach a current probe 1

POWER = VOLTAGE x CURRENT 3

Types of vertical axis wind turbines

1. Darrieus rotor 2. Savonius rotor 3. Multiple blade rotor 4. Musgrove rotor 5. Evans rotor https://www.google.co.in/url?sa=i&rct=j&q=&esrc=s&source=imgres&cd=&cad=rja& uact=8&ved=2ahUKEwj2qq65rI_dAhVMo48KHeqiDSkQjRx6BAgBEAU&url=http%3A% 2F%2Fwww.mechanicalbooster.com%2F2017%2F01%2Ftypes-of-wind- turbines.html&psig=AOvVaw11zXvVPrcpavI3GoRJPMe_&ust=1535531959661304

TIDAL ENERGY

TIDAL ENERGY Tidal Energy

– It is a form of hydropower that converts the energy of tides into useful forms of power ,mainly electricity. – It is the only form of energy whose source is the moon

• https://youtu.be/VkTRcTyDSyk

Types of tidal energy Technologies

• Tidal barrages • Tidal steam generators • Dynamic

» (explanation in video) Components of Tidal Barrage Power Plants

• Barrage or Dyke or Dam • Sluice ways • Embankments • Power house COMPONENTS OF TIDAL BARRAGE POWER PLANTS • Main Components are: – Barrage or Dyke/Dam – Sluice Ways – Embankments – Power House Modes of operation of Tidal Barrage Power Plants • Ebb generation • Flood generation • Two way genberation • Pumping and turbinig Tidal Barrage

from http://www.esru.strath.ac.uk/EandE/Web_sites/01- 02/RE_info/tidal1.htm

Modes of Operation of Tidal Barrage Power Plants • Ebb generation • Flood generation • Two-way generation 1.Ebb generation • Flood generation

Modes of generation of tidal barrage power • Single basin arrangement – Single ebb-cycle system – Single tide-cycle system – Double tide –cycle system • Double basin arrangement

GEO THERMAL ENERGY

GEO THERMAL ENERGY

• Utilize temperature of the earth’s core. • Direct use: District Heating System • • Heat pump

Direct District Heating System

• Use hot water from springs or reservoirs near the surface. • Hot water near the earth's surface can be piped directly into buildings and industries for heat. Electricity Generation

• Dry Steam Power Plant: Uses the superheated, pressurized steam (180°- 350°C) Electricity Generation

• Flash Steam Power Plant: use hot water above 182°C (360°F) from geothermal reservoirs. Electricity Generation

• Binary Cycle Power Plant: – Insufficiently hot resource to efficiently produce steam – Too many chemical impurities to allow flashing. Heat Pumps

• Utilizes constant temperature of upper 10 feet of the Earth’s surface. • Similar to ordinary heat pumps, but they rely on more stable source than air.

BIO ENERGY

• Energy obtained from organic matter derived from biological organisms (plants and animals) is known as bio energy. • energy may be transformed either by chemical/biological process to produce intermediate bio such as methane, producer gas, ethanol & charcoal etc.,

BIOMASS RESOURCES: –Biomass from cultivated fields, crops & forests –Biomass from municipal waste, animal dung, forest waste, agricultuiral waste USE OF BIO MASS for producing the process heat, electricity, gaseous &solid fuels,liquid & chemicals Factors affecting Digestion Process

1. pH Ocncentration 2. Total Oslid content 3. Seeding 4. Temperatuure 5. Loading rate 6. Type of feed 7. Pressure 8. Nutrients 10.Diameter to depth ratio 11.Mixing of content 12.Retention time/rate of feeding 13.Carbon to nitrogen ratio 14.Uniform feeding

FLOATING DOME TYPE