DOCSLIB.ORG

A Study of a Skirtless Hovercraft Design

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
A Study of a Skirtless Hovercraft Design Air Force Institute of Technology AFIT Scholar Theses and Dissertations Student Graduate Works 5-2004 A Study of a Skirtless Hovercraft Design Edward A. Kelleher Follow this and additional works at: https://scholar.afit.edu/etd Part of the Aerospace Engineering Commons Recommended Citation Kelleher, Edward A., "A Study of a Skirtless Hovercraft Design" (2004). Theses and Dissertations. 3913. https://scholar.afit.edu/etd/3913 This Thesis is brought to you for free and open access by the Student Graduate Works at AFIT Scholar. It has been accepted for inclusion in Theses and Dissertations by an authorized administrator of AFIT Scholar. For more information, please contact [email protected]. A STUDY OF A SKIRTLESS HOVERCRAFT DESIGN THESIS Edward A. Kelleher, Ensign, USNR AFIT/GAE/ENY/04-J05 DEPARTMENT OF THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED. The views expressed in this thesis are those of the author and do not reflect the official policy or position of the United States Navy, United States Air Force, Department of Defense, or the United States Government. AFIT/GAE/ENY/04-J05 A STUDY OF A SKIRTLESS HOVERCRAFT DESIGN THESIS Presented to the Faculty Department of Aeronautics and Astronautics Graduate School of Engineering and Management Air Force Institute of Technology Air University Air Education and Training Command In Partial Fulfillment of the Requirements for the Degree of Master of Science in Aeronautical Engineering Edward A. Kelleher, BS Ensign, USNR May 2004 APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED. AFIT/GAE/ENY/04-J05 A STUDY OF A SKIRTLESS HOVERCRAFT DESIGN Edward A. Kelleher, BS Ensign USNR Approved: ______ ___________ Dr. Milton Franke (Chairman) date ______ ___________ Lt Col Raymond C. Maple (Member) date ______ ___________ Lt Col Montgomery Houghson (Member) date Abstract Three proposed skirtless hovercraft designs were analyzed via computational fluid dynamics to ascertain their lift generation capabilities. The three designs were adaptations from William Walter’s hybricraft primer and his patent for a fan driven lift generation device. Each design featured Coanda nozzles, or nozzles that utilize the Coanda effect, to redirect air flow to aid in the generation of an air curtain around a central air flow. The designs also utilized a Coanda wing as a lifting body to aid in lift generation. Each design was set at a height above ground of one foot and a radius of two feet. The craft was assumed to be axisymmetric around a central axis for a perfectly circular craft, much like a flying saucer. The craft can be divided into several parts, the core, the nozzles, the plenum chamber (for designs 2 and 3), and the wing. Flow is generated from rotor blades situated one foot above the top of the core of the craft. The nozzles are located at the edges of the craft below the wing. In designs two and three the plenum chamber is the region between the core and the wing. For each design three cases were performed where t was increased for each case. This resulted in a total of nine cases, three cases for three designs. For each case the ratio of nozzle thickness to the radius of the curved plate, t/R, was set to 0.344 and t was increased while R was calculated to maintain the ratio. The computational fluid dynamics (CFD) analysis captured the pressure data and the lift forces were calculated using a pressure differential analysis. Analysis proved that the hybricraft designs could produce positive lift. While the first design did not produce positive lift, the second and third designs managed to generate enough lift to support a craft of a maximum of 52810.24 kg. The max amount of lift produced was 5388.8 N, while the minimum positive lift generated was 3642.9 N. iv Acknowledgments I would like to thank my thesis advisor, Professor Milton Franke for his help in this project and his producing of the idea. I would also like to extend my thanks to Lt Col Maple for all his help with understanding computational fluid dynamics and getting the computers to work for this thesis. Also, I want to extend a thanks to my fellow ensigns for their ever diligence in keeping the faith till the end. My final thanks is to my Coach, Raymond Bautista and the American Fencing Academy of Dayton for giving me something to distract me when needed. v ABSTRACT ................................................................................................................................................ IV LIFT OF FIGURES ................................................................................................................................. VII LIST OF TABLES...................................................................................................................................VIII LIST OF SYMBOLS.................................................................................................................................. IX INTRODUCTION........................................................................................................................................ 1 BACKGROUND ............................................................................................................................................ 1 BACKGROUND THEORY:............................................................................................................................. 3 CURRENT OBJECTIVES................................................................................................................................5 NUMERICAL MODEL SETUP ................................................................................................................. 8 RESULTS.................................................................................................................................................... 14 GENERAL.................................................................................................................................................. 14 DESIGN 1 .................................................................................................................................................. 14 DESIGN 2 .................................................................................................................................................. 19 DESIGN 3 .................................................................................................................................................. 24 ANALYSIS.................................................................................................................................................. 30 GENERAL.................................................................................................................................................. 30 DESIGN 1 .................................................................................................................................................. 31 Case 1: ................................................................................................................................................ 31 Case 2: ................................................................................................................................................ 32 Case 3: ................................................................................................................................................ 33 DESIGN 2 .................................................................................................................................................. 34 Case 1: ................................................................................................................................................ 34 Case 2: ................................................................................................................................................ 35 Case 3: ................................................................................................................................................ 36 DESIGN 3 .................................................................................................................................................. 38 Case 1: ................................................................................................................................................ 38 Case 2: ................................................................................................................................................ 39 Case 3: ................................................................................................................................................ 41 CONCLUSIONS AND RECOMMENDATIONS.................................................................................... 43 APPENDIX A ............................................................................................................................................. 46 APPENDIX B.............................................................................................................................................. 57 SOURCES ................................................................................................................................................... 58 VITAE ......................................................................................................................................................... 59 vi Lift of Figures Figure 1: Full Scale AVRO Car.........................................................................................
Load more

Recommended publications
  • A Study of a Skirtless Hovercraft Design
    A STUDY OF A SKIRTLESS HOVERCRAFT DESIGN THESIS Edward A. Kelleher, Ensign, USNR AFIT/GAE/ENY/04-J05 DEPARTMENT OF THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED. The views expressed in this thesis are those of the author and do not reflect the official policy or position of the United States Navy, United States Air Force, Department of Defense, or the United States Government. AFIT/GAE/ENY/04-J05 A STUDY OF A SKIRTLESS HOVERCRAFT DESIGN THESIS Presented to the Faculty Department of Aeronautics and Astronautics Graduate School of Engineering and Management Air Force Institute of Technology Air University Air Education and Training Command In Partial Fulfillment of the Requirements for the Degree of Master of Science in Aeronautical Engineering Edward A. Kelleher, BS Ensign, USNR May 2004 APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED. AFIT/GAE/ENY/04-J05 A STUDY OF A SKIRTLESS HOVERCRAFT DESIGN Edward A. Kelleher, BS Ensign USNR Approved: ______ ___________ Dr. Milton Franke (Chairman) date ______ ___________ Lt Col Raymond C. Maple (Member) date ______ ___________ Lt Col Montgomery Houghson (Member) date Abstract Three proposed skirtless hovercraft designs were analyzed via computational fluid dynamics to ascertain their lift generation capabilities. The three designs were adaptations from William Walter’s hybricraft primer and his patent for a fan driven lift generation device. Each design featured Coanda nozzles, or nozzles that utilize the Coanda effect, to redirect air flow to aid in the generation of an air curtain around a central air flow.
    [Show full text]
  • Exploring the Aerodynamic Characteristics of a Blown Annular-Wing for V/Stol
    EXPLORING THE AERODYNAMIC CHARACTERISTICS OF A BLOWN ANNULAR-WING FOR V/STOL AIRCRAFT A thesis submitted for the degree of Doctor of Philosophy by Burhan Saeed School of Engineering & Design Brunel University Project Supervisor(s): Dr Guy Gratton & Dr Cristinel Mares September 2010 ii ABSTRACT This research programme explores, theoretically and experimentally, a new lift- system for Vertical/Short Take-off and Landing (V/STOL) Aircraft. It is based upon an annular wing wrapped around a centrifugal flow generator, potentially creating a vehicle with no external moving parts, reduced vehicle aerodynamic losses compared to previous V/STOL technologies and substantially eliminating induced drag. It is shown that such a wing works best with a thick aerofoil section, and appears to offer greatest potential at a micro-aerial vehicle scale with regard to fundamental performance parameter “lift to weight ratio”. Certain efficiency losses are encountered mainly occurring from annular flow expansion and problems with achieving acceptable blower slot heights. Experimental methods are described along with results, and a comparison shows that the experimental values remain below theoretical values, partly due to flow asymmetry but possibly also other factors. Symmetrical blowing, as initially hypothesised, was found to be impracticable; this suggested use of pure upper surface blowing with Coanda effect. The modified approach was further explored and proved viable. The ultimate goal of this work was to develop an understanding and the facility to integrate the annular-wing into a vehicle to achieve controlled powered flight. To serve the purpose, issues encountered on current and past V/STOL aircraft are being investigated to set a path for further research/development and to validate/justify the design of future V/STOL aircraft.
    [Show full text]
  • Research, Development and Recent Patents on Aerodynamic Surface Circulation Control - a Critical Review
    Send Orders for Reprints to [email protected] Recent Patents on Mechanical Engineering 2014, 7, 1-37 1 Research, Development and Recent Patents on Aerodynamic Surface Circulation Control - A Critical Review Harijono Djojodihardjo* and Naveeyindren Thangarajah Department of Aerospace Engineering, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor Darul Ehsan, Malaysia Received: December 26, 2013; Accepted: January 17, 2014; Revised: January 22, 2014 Abstract: The ever increasing demand for better performance of aircraft aerodynamics, from the fundamental understand- ing of flight, requires enhanced circulation. Circulation Control and hence its enhancement can be achieved by surface blowing in the form of Coand jet and have always been referred to in the consideration of various flow control methods to enhance aerodynamic performance, along with continuous, synthetic and pulsed jets, compliant surface, vortex-cell, and the like. Coand jet has also been applied in the development of novel aircrafts for short takeoff, while another circu- lation enhancement technique known as Trapped Vortex Cavity (TVC) is currently being given significant considerations. It is with such motivation that salient features, progress and development of various techniques in circulation control are here identified, including some of the recent inventions that have been registered as patents in this area. The present work reviews the influence, effectiveness and configuration of airfoil surface blowing of Circulation Enhancement and Control of aerodynamic surfaces. The crux of the TVC active research is their stabilization, while Coand enhanced lift enhance- ment technique has, to a certain extent reached a stage that it can be easily implemented with advantage. Keywords: Aerodynamic surface blowing, circulation control, Coand effect, drag reduction, lift augmentation, trapped vortex cell, wall blowing.
    [Show full text]
  • Ms-364, Bernard Lindenbaum Vertical Flight Research Collection
    MS-364, BERNARD LINDENBAUM VERTICAL FLIGHT RESEARCH COLLECTION Collection Number: MS-364 Title: Bernard Lindenbaum Vertical Flight Research Collection Dates: 1918-1999 (Bulk 1945-1980) Creator: Lindenbaum, Bernard, 1916-2002 Summary/Abstract: Bernard Lindenbaum was an aeronautical engineer with the Air Force Flight Dynamics Laboratory (AFFDL) at Wright-Patterson Air Force Base in Dayton, Ohio from the mid-1940s until the mid-1970s. During his time with the laboratory, he was involved in the research and development of many types of vertical take-off and landing aircraft (VTOL) including the Avro “Avrocar,” a number of Sikorsky helicopters, the Vought XC-142 tilt wing, and many other similar aircraft. His collection of vertical flight research material contains numerous technical reports chronicling the development of military helicopters and V/STOL aircraft, a variety of conference reports and notes, many NACA/NASA technical notes, blueprints of several V/TOL aircraft, 190 reels of 16mm film and 10 VHS tapes of helicopter and V/STOL testing. Quantity/Physical Description: 126.3 linear feet Language(s): English Repository: Special Collections and Archives, Paul Laurence Dunbar Library, Wright State University, Dayton, OH 45435-001, (937) 775-2092 Restrictions on Access: There are no restrictions on accessing material in this collection. Restrictions on Use: Copyright restrictions may apply. Unpublished manuscripts are protected by copyright. Permission to publish, quote or reproduce must be secured from the repository and the copyright holder. Preferred Citation: (Box Number, Folder Number), MS-364, Bernard Lindenbaum Vertical Flight Research Collection, Special Collections and Archives, University Libraries, Wright State University, Dayton, Ohio Acquisition: The collection was donated by Stephen Lindenbaum of Marietta, Georgia, son of Bernard Lindenbaum, on March 24, 2003.
    [Show full text]
  • Avrocar: a Real Flying Saucer
    Avrocar: a real flying saucer Desire Francine G. Fedrigo* Panoramic Residence, Rua Lu´ısa,388s, ap. 05, Vila Portuguesa, Tangar´ada Serra/MT, 78300-000, Brasil Ricardo Gobato Secretaria de Estado da Educa¸c~aodo Paran´a(SEED/PR), Av. Maring´a,290, Jardim Dom Bosco, Londrina/PR, 86060-000, Brasil Alekssander Gobato Faculdade Pit´agorasLondrina, Rua Edwy Taques de Ara´ujo,1100, Gleba Palhano, Londrina/PR, 86047-500, Brasil *Corresponding author: [email protected] July 27, 2015 Keywords: AVRO Project, A. V. Roe Canada, Flying Saucer, Lockheed X-35, Military aircraft, Turbo Fan Engines, US Air Force, US Army. Abstract One of the most unusual military aircraft programs V / STOL was the Avro VZ-9 \Avrocar". Designed to be a real flying saucer, the Avrocar was one of the few V / STOL to be developed in complete secrecy. Despite significant changes in the design, during flight tests, the Avrocar was unable to achieve its objectives, and the program was eventually canceled after an expenditure of 10 million US dollars between 1954 and 1961. But the concept of a lift fan, driven by a turbojet engine is not dead, and lives today as a key component of Lockheed X-35 Joint Strike Fighter contender. Was held in a data research and information related to Avrocar project carried out during the Second World War, which was directly linked to advances in aircraft that were built after it, and correlate them with the turbo fan engines used today. arXiv:1507.06916v1 [physics.pop-ph] 24 Jul 2015 1 Introduction One of the most unusual military aircraft programs V / STOL was the Avro VZ- 9 \Avrocar" (Figure 1).
    [Show full text]