Instruction Manual High-Definition Link for Chevrolet(GM)
car-solutions.comLatest Firmware Date 2018 - 06 - 22 Manual Version Rev. 2.3 Release Date: 2018 - 12 – 05 Language English [email protected] car-solutions.com Contents • Cautions ______3 • Dimension & Exterior______4 • Components & Optional parts ______5 • Full Installation Diagram 「STINGRAY」 ______6 • Full Installation Diagram 「IMPALA, 2016 MALIBU, EQUINOX 」 ______7 • Full Installation Diagram 「SUBURBAN, 2016 GMC CANYON」 ______8 • HDMI Connection Diagram______11 • Navigation Connection Diagram ______12 • Compatibility Chart for Navigation(GPS) box models ______13 • LVDS Connection Diagram ______14 • Hazard Module Connection Diagram ______15 • Body Connector Specifications______16 • Car Compatibility Chart______17 • Activation by original buttons of 「STINGRAY」 ______18 • Activation by original buttons of 「IMPALA, 2016 MALIBU, EQUINOX 」____ 19 • DIP Switch Settings ______20 • Settings 1. Enter into the setting menu______21 2. HDMI mode settings ______22 3. NAVI mode settings______22 4. Rear view camera settings ______23 5. AV1(Front view camera) settings______23 6. Automatic activation function(AV1)______24 7. AV2 settings______24 8. System settings ______25 9. System information ______25 10. Informationcar-solutions.com of Dip switch settings ______26
[email protected] car-solutions.com Cautions
. Device-related • You should check the names and colors of each wires exactly, before you connect the wires. ex) CAN HIGH: White wires / CAN LOW: Blue wires
• The ‘POWER / CAN Cable’ should always be connected last and be disconnected first.
• The 'Mode Switch' is an optional part to change modes forcibly without CAN-BUS. Generally, the CAN-BUS wires are connected for changing modes by original buttons.
• When the reverse gear is not detected by CAN-BUS, the 'REVERSE 12V IN wire’ should be spliced with 12V power of reverse light.
. HDMI device-related • If screen size of HDMI does not fit on the monitor, should adjust screen size & position in 'settings mode'.
• Generally, '5V 1A Power output(5V USB POWER)' is a standard voltage for charging smartphone. If you need higher voltage than 5V, you should add a separate power supply.
. Navigation(GPS) box-related • When you connect the power wires(B+, ACC) to the navigation(GPS) box, the ‘NAVI (12V) OUT' wire supported by the device should be spliced with an ACC wire of navigation box.
• After installation is done, select an applicable navigation(GPS) box model in the 'Navigation model selection menu' of setting mode. • The navigation boxcar-solutions.com should be powered off before unplugging the HDMI cable.
3 [email protected] car-solutions.com Dimension
Length: 91 mm
Height: 22 mm
Width: 142 mm
Exterior ⓐ ⓑ ⓒ ⓓ ⓔ ⓐ DIP SWITCH ⓑ AV IN / OUT ⓒ TOUCH IN (Connect To Set top Device) ⓓ MODE ⓔ POWER / CAN ⓕ HDMI IN ⓖ 5V USB POWER ⓗ NAVI IN car-solutions.comⓘ UART I/F ⓙ LVDS OUT 4 [email protected] ⓕ ⓖ ⓗ ⓘ ⓙ car-solutions.com Components
Power / CAN LVDS CABLE LVDS PCB HDMI Cable AV IN / OUT CABLE 5-pin Micro USB Cable ※ Sub board Compatibility (FOR LVDS) Please refer to page14
Optional Parts(sold separately)
Mode Switch HDMI Extender LVDS CABLE (For stick type HDMI device) car-solutions.com- Suburban - 2016 GMC Canyon 5 [email protected] car-solutions.com Full Installation Diagram 「STINGRAY」 GROUND OUTPUT ※ NAVI 12V Power Output(NAVI 12V OUT) Corvette Stingray MY-LINK Touch Cable for Navigation Head Unit - 10pin Connector
※ Optional External Devices TOUCH LIN IN/OUT
TOUCH LIN OU T TOUCH LIN IN RV-CAM Video Input PIN # 8 = TOUCH LIN(Green/White) BUTTOM LIN External Rear View PIN # 5 = BUTTOM LIN(Green/Skyblue) 12V Power Output & GND Output(RV-CAM Power) SWITCH CAN Camera PIN # 3 = SWITCH CAN (Green) Reverse Signal Detection(optional) GROUND PIN # 10 = GND (Black/White) PIN # 1 = B+ POWER(Red/ Yellow) DIP S/W Setting B+ Power Input
NAVI Audio Input Audio(AUX) Output of Navigation Box
Audio Output
Auxiliary(AUX) Corvette Stingray MY-LINK Input of the car
HDMI USB HDMI USB HDMI FV-CAM Video Input (AV1) External Front View Camera HDMI HDMI USB
※ Sub board Compatibility car-solutions.com(Please refer to page14.) AV-Input(AV2) AV device HDMI (ex: DTV Box, Divx) V 1.0 6 [email protected] HDMI Device Navigation Box car-solutions.com Full Installation Diagram 「IMPALA, 2016 MALIBU, EQUINOX」
GROUND OUTPUT 내비게이션GGRROOUUNNDD 전원 OUTPUTOUTPUT접지(GROUND) 「Camaro,Volt」 내비게이션※ NAVI 12전원V Pow접지er Out(GRpOutU(NNDA)VI 12V OUT) ※※ 내비게이션용NNAAVIVI 1212VVPPoowerer12OutV 전원pputut(N(N출력AVII112V2V OUTOUT)) Chevrolet Impala, Malibu MY-LINK ※ 내비게이션용 12V 전원 출력 ChevroletChervolet Impala,SUBURBANMalibu MY-LINK MY-LINK 1 5 Chervolet SUBURBAN헤드 유닛 메인커넥터 MY-LINK Touch Cable 11 55 Head헤드 Unit 유닛 - 메인커넥터10pin Connector for Navigation 순정 헤드 유닛 Head Unit - 10pin Connector 순정 헤드 유닛 1 1 5 5 OEM6 메인커넥터Monitor10 Cable 1 5 메인커넥터 1 5 66 1010 ※ Optional External Devices TOUCH LIN IN/OUTTTOUCH LIN IN/OUTIN/OUT TOUCH LIN OU T 6 10 TOUCHTOUCHTOUCH LIN LINLIN INOUOU TT 6 10 66 1010 TOUCHTOUCH LINLIN ININ PIN # 8 = TOUCH LIN(Green/White) RV-CAM Video Input 핀PIN# # 8 = 88 =TTOUCHOUCH LIN(초록/흰색) LIN(Green/White) BUTTOM LIN 핀 # 8 = TOUCH LIN(초록/흰색) BUTTOMBUTTOM LINLIN PIN # 5 = BUTTOM LIN(Green/Skyblue) SWITCH CAN 핀PIN# # 5 = 55 =BUTBUTTOMTOM LIN(초록/하늘색) LIN(Green/Skyblue) External Rear View 핀PIN# #5 = 3 =BUTTOM LIN(초록/하늘색) 12V Power Output & GND Output(RV-CAM Power) SWITCHSWITCH CANCAN 핀 # 3 = SWISWITTCHCH CAN CAN (초록) (Green) Camera 핀PIN# 3# = 33SWI= SWITCHTCH CAN CAN (초록) (Green) Reverse Signal Detection(optional) GROUND 핀 # 10 = 접지 (검정/흰색) GROUND 핀PIN# 1#0 1=0 =접지GND (검정/흰색) (Black/White) 제공되는 인아웃 케이블 핀PIN# #11=0 =헤드유닛GND (Black/White) 전원(적색/노랑) 제공되는 인아웃 케이블 핀PIN# #1 =1 =헤드유닛B+ POWER(Red/ 전원(적색/노랑)Yellow) B+ Power Input PIN # 1 = B+ POWER(Red/Yellow) DIP S/W Setting B+B+ PowerPower InputInput
NAVI Audio Input Audio(AUX) Output of Navigation Box
Chevrolet MY-LINK LVDS & Main Harness Audio Output
Auxiliary(AUX) Input of the car
HDMI USB HDMI USB HDMI FV-CAM Video Input (AV1) Malibu Impala External Front View Camera HDMI HDMI USB
※ Sub board Compatibility car-solutions.com(Please refer to page14) AV-Input(AV2) AV device HDMI (ex: DTV Box, Divx) 7 [email protected] HDMI Device Navigation Box V 1.0 car-solutions.com Full Installation Diagram GROUND OUTPUT 내비게이션GRROUUNNDD 전원 OUTPUTOUTPUT접지(GROUND) 내비게이션※ NAVI 12전원V Po접지wer Out(GRpOutU(NNDA)VI 12V OUT) ※※ 내비게이션용NNAVI 1212VVPPoowerer12OutV 전원pputut(N(N출력AAVVII112V2V OUTOUT)) Chevrolet Impala, Malibu MY-LINK ※ 내비게이션용 12V 전원 출력 ChevroletChervolet Impala,SUBURBANMalibu MY-LINK MY-LINK 「Suburban , Silverado 1 5 Chervolet SUBURBAN헤드 유닛 메인커넥터 MY-LINKMY-LINK Touch Cable 11 55 Head헤드 Unit 유닛 - 메인커넥터10pin Connector for Navigation 순정순정 헤드 헤드 유닛 유닛 Head Unit - 10pin ConnectorConnector 1 1 5 5 GMC Canyon, Yukon」 OEM6 메인커넥터Monitor10 Cable 1 5 메인커넥터 11 55 6 10 6 10 ※ Optional External Devices TOUCH LIN IN/OUTTOUCH LIN IN/OUTIN/OUT TOUCH LIN OU T 6 10 TOUCHTOUCH LINLIN INOU T 66 10 TOUCH LIN OU T 66 101010 TOUCHTOUCH LINLIN ININ PIN # 8 = TOUCH LIN(Green/White) RV-CAM Video Input 핀PIN# # 8 =8 = TOUCH LIN(Green/White) BUTTOM LIN 핀PIN# 8#= 8T=OUCHTOUCHTOUCH LIN(초록/흰색) LIN(초록/흰색) LIN(Green/White) BUTTOMBUTTOM LINLIN PIN # 5 = BUTTOM LIN(Green/Skyblue) SWITCH CAN 핀핀PINPIN## 5## 5= = 55==BUTBUTBUTTOMTTOM LIN(초록/하늘색) LIN(Green/Skyblue)LIN(Green/Skyblue) External Rear View PIN # 3 BUT= SWITOMTCH LIN(초록/하늘색) CAN (Green) 12V Power Output & GND Output(RV-CAM Power) SWITCHSWITCH CANCAN 핀 # 3 = SWITCH CAN (초록) Camera 핀PINPIN# 3##= 33SWI==SWISWITCHTTCH CAN CANCAN (초록) (Green)(Green) GROUND Reverse Signal Detection(optional) 핀핀PIN##1#0101=0= 접지=접지 (검정/흰색) (검정/흰색) GGRROOUUNNDD GND (Black/White) 제공되는 인아웃 케이블 핀PINPIN# ##111=00 ==헤드유닛GND (Black/White) 전원(적색/노랑) 제공되는 인아웃 케이블 핀PIN# #1 =1 헤드유닛= B+ POWER(Red/ 전원(적색/노랑)Yellow) B+ Power Input PINPIN ## 11 ==B+B+ POWER(Red/POWER(Red/YYellow)ellow) DIP S/W Setting B+B+ PowerPower InputInput
NAVI Audio Input Audio(AUX) Output of Navigation Box
GMC Canyon
Audio Output
Auxiliary(AUX) Input of the car
HDMI USB HDMI USB HDMI FV-CAM Video Input (AV1) External Front View Camera ※ behind the My-link ※ behind the glove box HDMI HDMI USB
※ Sub board Compatibility (Please refer to page14) car-solutions.comOEM LVDS순정케이블 Cable AV-Input(AV2) AV device HDMI (ex: DTV Box, Divx) 제공되는Provided 케이블 LVDS Cable 8 [email protected] HDMI Device Navigation Box car-solutions.com HDMI Connection Diagram
HDMI Device HDMI Device
HDMI IN 5V USB NAVI IN UART I/F LVDS OUT HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER POWER
HDMI USB HDMI USB
HDMI HDMI (5V-1A Power output for HDMI Device) (5V-1A Power output for HDMI Device) (Male) (Female)
(HDMI Extender) (HDMI Cable) ‘Stick Type’ HDMI Devices ‘Dongle & Adapter’ Type HDMI Devices
car-solutions.com
11 [email protected] car-solutions.com Navigation Connection Diagram Navigation Connection Diagram
Navigation(GPS) Box Navigation(GPS) Box
HDMI IN 5V USB NAVI IN UART I/F LVDS OUT HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER POWER
HDMI HDMI USB
TOUCH IN TOUCH IN
(USB Cable is connected with the ‘N-Link’, only) USB HDMI
car-solutions.comHDMI iNAVI – X1 CUBE MICROCITY - N-Link 12 [email protected] car-solutions.com Compatibility Chart for Navigation(GPS) box models
Dip S/W Model Country Required Parts (Navigation)
MICROCITY South Korea - N-Link
HDMI Cable USB A-A Cable Hazard Module
OFF iNAVI ↓ South Korea X1 CUBE ON 1 2 3 4 HDMI Cable OFF(↑): 1, 2, 3, 4
ON ↑ MYVI South Korea 1 2 3 4 MS1400 Digital OFF(↓): 1, 2, 3 HDMI Cable ON(↑) : 4
• This device supports navigation(GPS)car-solutions.com box models equipped with 'Digital video output'.
• It does not support the 'RGB video signals'. 13 [email protected] car-solutions.com LVDS Connection Diagram
LVDS Connection
HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER 2016 GMC CANYON ※ behind the My-link ※ behind the glove box
• 'Genuine(OEM) LVDS connector' should be connected to 'LVDS IN / OUT PCB'. HDMI • ‘Provided LVDS connector' should be connected to the monitor instead to the genuine connector. ※ behind the Monitor ※ behind the Monitor ※ Sub board Compatibility Sheet
V 1.0 V 1.1
- Corvette Stingray - Chevrolet Suburban ※ behind the Monitor - Chevrolet Impala - Silverado LCD - 2016~ Malibu - GMC Canyon - 2016~ Camaro - GMC Yukon Cable - 2016~ Volt - 2018~ Equinox
(Provided LVDS Cable)
HDMI car-solutions.com(OEM LVDS Cable) V 1.0 14 [email protected] car-solutions.com Hazard Module Connection
POWER / CAN MODE TOUCH-IN AV IN / OUT DIP SWITCH
IMPALA - Hazard button
1 2 3 4 5 6 7 8 9 10 11
12 13 14 15 16 17 18 19 20 21 22
4-pin Hazard connector NAVI NAVI AUD INR NAVI NAVI AUD INL REAR REAR CAMERA AUDIO AUDIO R OUT AUDIO AUDIO L OUT AV2 AV2 INV AV2 AV2 INR AV2 AV2 INL AV1 AV1 IN V REVERSE 12VIN REAR REAR 12V
New Version Module
Hazard Module PIN # 2 = Hazard(-) (Green/White) GROUND
IR IR OUT (4-Pin)
(For Only Benz) BMW/AUDI Light Hazard Benz Hazard Light BenzHazard IR IN GND car-solutions.com(20 cm) (100 cm) *Hazard Module is just available with ‘Smart Drive function of N-Link’ navigation in South Korea. 15 [email protected] car-solutions.com Body Connector specifications
POWER / CAN MODE TOUCH-IN AV IN / OUT DIP SWITCH
1 2 3 4 5 6 7 8 9 10 11
1 2 3 4 5 6 7 8 9 10 1 2 1 2 3 4 12 13 14 15 16 17 18 19 20 21 22 Length : 100 cm Length: 20 cm NAVI NAVI AUD INR NAVI NAVI AUD INL REAR REAR CAMERA AUDIO AUDIO R OUT AUDIO AUDIO L OUT TOUCH LINOUT TOUCH BUTTON LIN IN LINBUTTON AV2 AV2 INV AV2 AV2 INR AV2 AV2 INL TOUCH LININ TOUCH AV1 AV1 IN V NAVI NAVI 12V OUT SW CAN H CAN SW GROUND GROUND REVERSE 12VIN BAT BAT + GROUND REAR REAR 12V IR IR OUT
Length: 150 cm Length: 100 cm
1 BATTERY POWER INPUT 1 RV-CAM VIDEO INPUT 12 GND(RV-CAM VIDEO) 2 GND INPUT 2 RV-CAM POWER OUT 13 GND OUTPUT(RV-CAM) 3 GND OUTPUT 3 REVERSE DETECTION 14 IR OUT 4 ACC(12V) POWER OUTPUT 4 NAVI AUX INPUT R 15 GND(NAVI AUX IN R) 5 SINGLE WIRE CAN 5 NAVI AUX INPUT L 16 GND(NAVI AUX IN L)
6 BUTTON LIN 4 3 2 1 6 AUDIO OUTPUT R 17 GND(AUDIO OUT R) 7 - 7 AUDIO OUTPUT L 18 GND(AUDIO OUT L) 8 - 8 AV1 VIDEO INPUT 19 GND(AV1 VIDEO IN) Connector type 9 TOUCH LINK IN Push Switch 9 AV2 VIDEO INPUT 20 GND(AV2 VIDEO IN) 10 TOUCH LINK OUT 10 AV2 AUDIO INPUT R 21 GND(AV2 AUDIO IN R) car-solutions.com11 AV2 AUDIO INPUT L 22 GND(AV2 AUDIO IN L)
• The colors of each wires can be changed under manufacturer’s circumstance. 16 [email protected] car-solutions.com Car Compatibility Chart
Production Car Models Specific Models Year corvette 2015~ C7 (8 inch Equipped with MyLink) stingray
Equinox 2018~ Equipped with MyLink
Chevrolet 2015~ Equipped with MyLink Suburban Chevrolet 2015~ Equipped with MyLink This device is used in combination Impala with Chevrolet(GM) INFOTAINMENT Chevrolet 2016~ 8 inch Equipped with MyLink system. Malibu
GMC Canyon 2016~ Equipped with MyLink
GMC Yukon 2016~ Equipped with MyLink
CAMARO 2016~ Equipped with MyLink This device supports the 6th GEN Chevrolet(GM) original screen & Volt 2016~ 8 inch Equipped with MyLink Head unit equipped with ‘LVDS
connector’ only.
Please check the specification of
original LVDS connector on the car-solutions.comsidelines of a production year.
17 [email protected] car-solutions.com Activation by original buttons of 「Corvette Stingray」
Stingray – MyLink
Button Function Operation Remarks
Changing 1 Press the button 2 seconds long. Order: HDMI → NAVI → AV1 → AV2 → OEM Modes HOME
Press the button 2 times quickly. < OEM → NAVI > Shortcut to 1 Press the button 3 times quickly. < OEM → AV1 > Each modes HOME Press the button 4 times quickly. < OEM → AV2 >
System If you visit car service center, you can lock the all 1 Locking / Press the button 10 seconds long. functions of this device.- It is only possible to use the HOME Unlocking OEM functions under it is locked.
Buttons marked Back to OEM Press the buttons short. Return to the OEM mode in any modes. with yellow
Changing mode It changes the screen from any modes to AV1 mode 2 to Front View Press the button 2 seconds long. 1 2 directly. BACK CAM mode(AV1)
Reset to factory You can use this function when you get in trouble to 2 default setting Press the button 10 seconds long. see the screen while setting the screen. BACK and power.
All functions of setting menu of this device are Enter into the Touch the oem screen 5 seconds controlled setting menu long. by a touch screen of the OEM monitor. Touch the car-solutions.comoem screen
18 [email protected] car-solutions.com Activation by original buttons of 「Chevrolet Impala, 2016 Malibu」
Impala, 2016 Malibu – MyLink
Button Function Operation Remarks
1 Changing Modes Press the button 2 seconds long. Order: HDMI → NAVI → AV1 → AV2 → OEM 1 HOME Press the button 2 times quickly. < OEM → NAVI > Shortcut to each 2 1 Press the button 3 times quickly. < OEM → AV1 > modes HOME Press the button 4 times quickly. < OEM → AV2 >
System If you visit car service center, you can lock the all 1 Locking / Press the button 10 seconds long. functions of this device . It is only possible to use the HOME Unlocking OEM functions under it is locked.
Impala Buttons Back to OEM Press the buttons short. Return to the OEM mode in any modes. marked with yellow
Changing mode It changes the screen from any modes to AV1 mode to Front View Press the button 2 seconds long. 2 directly. BACK CAM mode(AV1)
Reset to factory You can use this function when you get in trouble to default setting Press the button 10 seconds long. 2 see the screen while setting the screen. BACK and power. 1 All functions of setting menu of this deviceare 2 Enter into the Touch the oem screen 5 seconds controlled setting menu long. by a touch screen of the OEM monitor. Touch the car-solutions.comoem screen Malibu 19 [email protected] car-solutions.com DIP Switch Settings
OFF ON: ▼ OFF:▲ ON No.6 No.7 No.8 No.9 No.10 Car Models
Corvette Stingray
OFF(▲) OFF(▲) OFF(▲) OFF(▲) ON(▼) Chevrolet Impala
OFF(▲) OFF(▲) OFF(▲) ON(▼) ON(▼) 2016 Chevrolet Impala
External Front View Skip External Front View OFF(▲) OFF(▲) ON(▼) ON(▼) ON(▼) 2017 Chevrolet Impala
8
9 Selection of car model 5(F10) *6.5-inch국외 (‘INNOLUX’) OFF(▲) OFF(▲) ON(▼) ON(▼) ON(▼) X3(F25) *6.5-inch국외(‘JOHNSON’) 10 car-solutions.com
20 [email protected] car-solutions.com Settings
Button Function Operation
Touch the oem Enter into the Touch the oem screen 5 screen setting menu seconds long.
All functions of setting menu of IW03GF is controlled Touch Screen (OEM Monitor) by a touch screen of the OEM monitor.
1. Enter into the setting menu.
- HDMI & Navigation settings
- Rear view camera settings
- AV-input settings car-solutions.com- System settings - System information 21 [email protected] car-solutions.com Settings
2. HDMI mode settings
- Mode selection: HDMI ↔ NAVI
- Image display = Adjust the values of brightness and contrast Red-Green-Blue colors of HDMI display.
- Screen position & size = Entry Disabled / Not applicable.
3. NAVI mode settings
- Mode selection: NAVI ↔ HDMI
- Image display = Adjust the values of brightness and contrast Red-Green-Blue colors of NAVI display.
- Screen position & size = Entry Disabled / Not applicable. car-solutions.com- Navigation Resolution selection = Entry Disabled / Not applicable. 22 [email protected] car-solutions.com Settings
4. Rear view camera settings
- Parking guide lines = Adjust position of parking guide lines and select the lines ‘ON or OFF’.
- Parking distance control = Adjust the position of parking distance control sensors to ‘LEFT or RIGHT’ and select the PDC ‘ON or OFF’.
- Image display = Adjust the values of brightness and contrast Red-Green-Blue colors of Rear view camera display.
5. AV1(Front view camera) settings
- Mode selection: AV1(Front view camera) ↔ AV2
- Image display = Adjust the values of brightness and contrast Red-Green-Blue colors of AV1(Front view camera) display.
- Screen position & size = Entry Disabled / Not applicable.
- Automatic activation function(AV1) car-solutions.com= * Please refer to next page. - Parking distance control = Adjust the position of parking distance control sensors 23 [email protected] to ‘LEFT or RIGHT’ and select the PDC ‘ONcar-solutions.com or OFF’. Settings
6. Automatic activation function(AV1)
- Shift gear from reverse to drive
- Shift gear from parking to drive
* When you shift gear ‘from reverse to drive’ or ‘from parking to drive’, it just works automatically during the activation time you selected.
7. AV2 settings
- Mode selection: AV2 ↔ AV1(Front view camera)
- Image display = Adjust the values of brightness and contrast Red-Green-Blue colors of AV2 display.
- Screen position & size car-solutions.com= Entry Disabled / Not applicable.
24 [email protected] car-solutions.com Settings
8. System settings
- Safe mode = Select the one of two between ‘ON and OFF’.
* If you select ‘ON’, 3 modes(HDMI, NAVI and AV2) will be faded out when the car is driven.
- Factory default = Reset all setting values to factory default setting.
9. System information
- Mode name :
- Firmware date : 2017 – 06 – 09 (Latest firmware date)
- = You can check the current firmware version date.
- Dip switch settings = You can check the current positions of dip switch settings. car-solutions.com
25 [email protected] car-solutions.com Settings
10. Information of Dip switch settings
* You can check the current positions of dip switch settings.
ex 1) ex 2) Actual DIP switch values. (→) Actual DIP switch values. (→)
Appears on the setting menu. (↓) Appears on the setting menu. (↓)
car-solutions.com
26 [email protected] car-solutions.com