1988Ͳ99 Jeep Wrangler, 1989Ͳ 99 Jeep Cherokee & 1989Ͳ92
Total Page:16
File Type:pdf, Size:1020Kb
InstallaƟ on InstrucƟ ons 45059 1988ͳ99 JEEP WRANGLER, 1989ͳ 99 JEEP CHEROKEE & 1989ͳ92 JEEP COMANCHE with AX15 Manual Transmission 4 5 2 3 1 ITM # PART # DESCRIPTION QTY. 1 6410056 Shi Assembly 1 2 4100497 Small Shi er Boot 1 3 4100499 Retaining Boot Ring (Small) 1 4 4101359-88 Shi Knob 1 5 1794719 Shi Handle ⁄-16 Lock Nut 1 www.bmracing.com Rev 02/21/20 Technical Support (866) 464-6553 Page 1 of 6 OVERVIEW: 3. Remove stock shi knob jam nut. 1. This B&M Precision SportShi er is specifi cally designed for 1990-98 Jeep Wrangler 4.0L models with AX-15 5-speed manual transmission but is also compa ble with 90-98 Jeep Cherokee and Comanche. It is engineered to greatly reduce shi throw and improve shi feel. NOTE: Please inventory all parts now and if necessary, report any missing items to our tech line. WARNING: For maximum safety, perform this installa on on a clean, level surface with engine turned off . CAUTION: To avoid bodily injury or vehicle damage, chock wheels and do not a empt installa on un l you are confi dent your vehicle will not move. 4. Remove stock shi knob. REMOVE STOCK COMPONENTS: NOTE: Some steps may contain mul ple images to cover all applica ons for this product. 2. Remove stock shi knob insert. 5. Remove shi boot. 45059 www.bmracing.com Rev 02/21/20 Technical Support (866) 464-6553 Page 2 of 6 6. Remove and retain center console fastener near 9. Remove and retain center console bolts (x2) from shi er. storage console. 7. Remove 4wd selector cover or remove and retain 10. Pull up 4-wheel drive shi lever. fasteners securing passenger side of center console. 8. Remove and retain and center console fasteners 11. Remove center console. from cup holder or under 4wd selector. 45059 www.bmracing.com Rev 02/21/20 Technical Support (866) 464-6553 Page 3 of 6 12. Remove bolts and rubber protec ve boot. 15. Clean moun ng surface on transmission. NOTE: It may be necessary to trim boot slightly around s ck to remove it. Assemble & Install Precision Sport ShiŌ er: 13. Remove bolts (x4) securing shi er to transmission. 16. Press pivot cup onto B&M Shi er. NOTE: Inspect pivot cup for wear and tear. If necessary, 17. Install new shi er base gasket (not included) or you may want to purchase another before comple ng apply RTV silicone sealant to the B&M shi er base. this install. 14. Pry pivot cup from stock shi er. 45059 www.bmracing.com Rev 02/21/20 Technical Support (866) 464-6553 Page 4 of 6 18. Fasten shiŌ assembly (1) to factory shi er base 21. Set center console cover back into place. using bolts (x4) removed step 13. 19. Use retaining boot ring (3) to secure shiŌ er boot (2) onto shi er base. 22. Secure center console using fasteners from step 6 through 9. 20. Re-install rubber protec ve boot and bolts removed step 12. 45059 www.bmracing.com Rev 02/21/20 Technical Support (866) 464-6553 Page 5 of 6 5 23. Re-install shi boot, then thread shiŌ handle lock 26. Test shi er engagement in each gear, then ghten nut (5) onto shi er stem. all parts and verify shi er func on once more. WARNING: DO NOT operate vehicle un l all gears can be smoothly and fully engaged. 24. Thread shiŌ knob (4) onto shi er stem. Congratula ons, the installa on of your B&M Precision SportShi er is now complete! 25. Adjust knob un l it is in op mal posi on, then ghten it in combina on with lock nut to secure it in place. 45059 www.bmracing.com Rev 02/21/20 Technical Support (866) 464-6553 Page 6 of 6.