Owner's Manual

NV200 OWNER’S MANUAL Foreword

Welcome to the growing family of new NISSAN owners. This vehicle has been delivered to you with confidence. It has been produced using the latest techniques and strict quality control. This manual was prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many kilometres (miles) of driving pleasure. Please read through this manual before operating your vehicle. A separate Warranty Information & Maintenance Booklet explains in detail the warranty coverage that applies to your vehicle. Your NISSAN dealer knows your vehicle best. When you require any service or have any questions, your NISSAN dealer will be glad to assist you with the extensive resources available for you.

IMPORTANT SAFETY INFORMATION MODIFICATION OF YOUR VEHICLE REMINDERS FOR SAFETY! This vehicle should not be modified. Modifications could affect its performance, safety or durability, and may even violate governmental regulations. In addition, Follow these important driving rules to help ensure a safe and complete trip for damage or performance problems resulting from modifications may not be cov- you and your passengers! ered under NISSAN warranties. NEVER drive under the influence of alcohol or drugs. • READ FIRST — THEN DRIVE SAFELY ALWAYS observe posted speed limits and never drive too fast for condi- • Before driving your vehicle, read this Owner’s Manual carefully. This will ensure tions. familiarity with controls and maintenance requirements, assisting you in the safe • ALWAYS use your seat belts and appropriate child restraint systems. operation of your vehicle. Preteen children should be seated in the rear seat. Throughout this manual the following symbols and words are used: • ALWAYS provide information about the proper use of vehicle safety fea- tures to all occupants of the vehicle. WARNING • ALWAYS review this Owner’s Manual for important safety information. Indicates the presence of a hazard that could cause death or serious per- WHEN READING THE MANUAL sonal injury. To avoid or reduce the risk, the procedures described must be followed precisely. This manual includes information for all options available on this model. There- fore, you may find some information that does not apply to your vehicle. CAUTION All information, specifications and illustrations in this manual are those in effect Indicates the presence of a hazard that could cause minor or moderate per- at the time of printing. NISSAN reserves the right to change specifications or sonal injury, or damage to your vehicle. To avoid or reduce the risk, the pro- designs at any time without notice and without obligation. cedures described must be followed carefully. NOTE Indicates additional helpful information. The NISSAN GREEN PROGRAM symbol indicates environmentally friendly BATTERY DISPOSAL information and best practices. CAUTION An improperly disposed battery can harm the environment. Always confirm local regulations for battery disposal. Examples of the batteries that the vehicle contains: • Vehicle battery • Remote controller battery (for Intelligent Key and/or Remote keyless entry system) • Tyre Pressure Monitoring System (TPMS) sensor battery • Remote controller battery (for Mobile Entertainment system) This symbol means “Do not do this” or “Do not let this happen”. If in doubt, contact your local authority, or a NISSAN dealer, or a qualified workshop for advice on disposal.

Arrows in an illustration that are similar to these point to the front of the vehicle.

Arrows in an illustration that are similar to these indicate movement or action.

Arrows in an illustration that are similar to these call attention to an item in the illustration.

Contents Illustrated table of contents 0

Safety — seats, seat belts and supplemental restraint system 1

Instruments and controls 2

Pre-driving checks and adjustments 3

Display screen, heater and air conditioner, and audio system 4

Starting and driving 5

In case of emergency 6

Appearance and care 7

Maintenance and do-it-yourself 8

Technical information 9

Index 10

0 Illustrated table of contents

Seats, seat belts and Supplemental Restraint Instrument panel ...... 0-8 System (SRS)...... 0-2 Left-hand drive (LHD) model...... 0-8 Exterior front...... 0-3 Right-hand drive (RHD) model ...... 0-9 Exterior rear...... 0-4 Meters and gauges...... 0-10 Passenger compartment ...... 0-5 Engine compartment...... 0-11 Cockpit ...... 0-6 HR16DE engine model ...... 0-11 Left-hand drive (LHD) model...... 0-6 K9K engine model ...... 0-12 Right-hand drive (RHD) model ...... 0-7 SEATS, SEAT BELTS AND SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

11. Third row seats* (P. 1-5) *: where fitted

SSI0596

1. Supplemental front-impact air bags* (Page 6. Second row centre seat belt* (P. 1-10) 1-21) 7. Front seats (P. 1-2) 2. Supplemental side-impact air bags* (P. 1-21) 8. Pre-tensioner seat belt system (P. 1-23) 3. Seat belts (P. 1-7) 9. Second row seats* (P. 1-3) 4. Head restraints (P. 1-6) — Child restraints (P. 1-11) 5. ISOFIX child restraint system* (P. 1-11) 10. Child restraint anchor points (for top tether strap child restraint)* (P. 1-15)

0-2 Illustrated table of contents EXTERIOR FRONT

8. Tyres — Tyres and wheels (P. 8-26, P. 9-6) — Flat tyre (P. 6-2) — Tyre placard (P. 9-8) 9. Side turn signal light — Switch operation (P. 2-21) — Bulb replacement (P. 8-22) 10. Outside mirrors (P. 3-23) 11. Doors — Keys (P. 3-2) — Door locks (P. 3-4) — Intelligent Key system* (P. 3-10) — Remote keyless entry system* (P. 3-8) 12. Child safety sliding door lock* (P. 3-8) *: where fitted

SSI0597

1. Engine bonnet (P. 3-19) — Switch operation (P. 2-17) — Bulb replacement (P. 8-21, P. 8-22) 2. Windscreen wiper and washer — Switch operation (P. 2-22) 5. Windows (P. 2-25) — Blade replacement (P. 8-15) 6. Recovery hook (P. 6-9) — Window washer fluid (P. 8-16) 7. Fog lights* 3. Antenna (P. 4-9) — Switch operation (P. 2-21) 4. Headlights and turn signal lights — Bulb replacement (P. 8-22)

Illustrated table of contents 0-3 EXTERIOR REAR

— Intelligent Key system* (P. 3-10) — Remote keyless entry system* (P. 3-8) 9. Number plate lights — Bulb replacement (P. 8-22) 10. Recovery hook (P. 6-9) 11. Stop/tail lights — Bulb replacement (P. 8-22) 12. Reverse light (LHD model) or Fog light (RHD model) — Fog light switch operation (P. 2-21) — Bulb replacement (P. 8-22) 13. Turn signal lights — Switch operation (P. 2-21) — Bulb replacement (P. 8-22) 14. Fuel filler lid — Opener operation (P. 3-22) — Fuel recommendation (P. 9-4) *: where fitted jA Tailgate model SSI0744 jB French door model

1. Rear window wiper and washer* 5. Sliding door(s) (P. 3-6) — Switch operation (P. 2-23) 6. Fog light (LHD model) or Reverse light (RHD — Window washer fluid (P. 8-16) model) 2. High-mounted stop light — Fog light switch operation (P. 2-21) — Bulb replacement (P. 8-22) — Bulb replacement (P. 8-22) 3. Rear window defogger (P. 2-24) 7. Rear view camera* (P. 4-2) 4. Sliding windows* (P. 2-25) 8. Back door (P. 3-20)

0-4 Illustrated table of contents PASSENGER COMPARTMENT

12. Second row seat power outlet* (P. 2-27) 13. Rear cooler fan switch* (P. 4-7) 14. Luggage room — Storage (P. 2-28) — Luggage hooks (P. 2-32) — Tonneau cover* (P. 2-32) *: where fitted

NIC1625

1. Inside rearview mirror* (P. 3-23) 6. Bottle holders* (P. 2-29) 2. Sun visors (P. 2-33) 7. Sliding windows* (P. 2-25) — Ticket holders (P. 2-31) 8. Third row seat cup holders* (P. 2-30) 3. Door armrest 9. Luggage compartment light (P. 2-34) — Power window switch* (P. 2-25) 10. Console box (P. 2-29) 4. Room lights (P. 2-34) 11. Rear cup holders (P. 2-29) 5. Room lights* (P. 2-34)

Illustrated table of contents 0-5 COCKPIT

10. Outside rearview mirror remote control switch* (P. 3-23) 11. Steering wheel — Electric power steering system (P. 5-14) — Horn (P. 2-25) — Driver supplemental air bag (P. 1-21) 12 Ignition switch/steering lock (P. 5-4) 13. Shift lever for Manual Transmission (MT) model (P. 5-8) 14. Parking brake (P. 3-24, P. 5-11) *: where fitted

SSI0622

LEFT-HAND DRIVE (LHD) MODEL 5. Wiper and washer switch (P. 2-22) 1. Front cup holder (P. 2-29) 6. Fuel filler lid opener handle (P. 3-22) 2. Side vent (P. 4-4) 7. Bonnet release handle (P. 3-19) 3. Headlight, fog light and turn signal switch 8. Card holder (P. 2-31)/Fuse box cover (P. 2-17) (P. 8-21) 4. Meters and gauges (P. 2-2) 9. Headlight aiming control switch (P. 2-18)

0-6 Illustrated table of contents 10. Steering wheel — Electric power steering system (P. 5-14) — Horn (P. 2-25) — Driver supplemental air bag (P. 1-21) 11. Ignition switch/steering lock (P. 5-4) 12. Bonnet release handle (P. 3-19) 13. Fuel filler lid opener handle (P. 3-22) 14. Card holder (P. 2-31)/Fuse box cover (P. 8-21) *: where fitted

SSI0601

RIGHT-HAND DRIVE (RHD) MODEL 5. Headlight aiming control switch (P. 2-18) 1. Headlight, fog light and turn signal switch 6. Side vent (P. 4-4) (P. 2-17) 7. Front cup holder (P. 2-29) 2. Meters and gauges (P. 2-2) 8. Parking brake (P. 3-24, P. 5-11) 3. Wiper and washer switch (P. 2-22) 9. Shift lever for Manual Transmission (MT) 4. Outside rearview mirror remote control switch* model (P. 5-8) (P. 3-23)

Illustrated table of contents 0-7 INSTRUMENT PANEL

10. Ashtray (P. 2-28) 11. Power door lock switch* (P. 3-6) 12. Front passenger air bag status light* (P. 1-26) 13. Heater/air conditioner* control (P. 4-4) 14. Utility hook (P. 2-31) 15. Glove box (P. 2-28) *: where fitted

SSI0603

LEFT-HAND DRIVE (LHD) MODEL 5. Rear cooler front switch* (P. 4-7) or Electronic Stability Programme (ESP) off switch* (P. 5-9) 1. Centre vent (P. 4-4) 6. Rear cooler front switch* (P. 4-7) 2. Audio system* (P. 4-8) or Centre box* — Clock* (P. 2-27) 7. Defogger switch* (P. 2-24) 3. Passenger’s front-impact air bag* (P. 1-21) 8. Hazard indicator flasher switch (P. 2-24) 4. Steering wheel lock lever (P. 3-23) 9. Front power outlet* (P. 2-27)

0-8 Illustrated table of contents 11. Ashtray (P. 2-28) 12. Hazard indicator flasher switch (P. 2-24) 13. Rear cooler front switch* (P. 4-7) 14. Rear cooler front switch* (P. 4-7) or Electronic Stability Programme (ESP) off switch* (P. 5-9) 15. Steering wheel lock lever (P. 3-23) *: where fitted

SSI0602

RIGHT-HAND DRIVE (RHD) MODEL 5. Utility hook (P. 2-31) 1. Passenger’s front-impact air bag* (P. 1-21) 6. Heater/air conditioner* control (P. 4-4) 2. Centre vent (P. 4-4) 7. Defogger switch* (P. 2-24) 3. Audio system* (P. 4-8) or Centre box* 8. Front passenger air bag status light* (P. 1-26) — Clock* (P. 2-27) 9. Power door lock switch (P. 3-6) 4. Glove box (P. 2-28) 10. Front power outlet* (P. 2-27)

Illustrated table of contents 0-9 METERS AND GAUGES

9. Trip odometer (P. 2-2) 10. Odometer (P. 2-2) *: where fitted

SSI0604

1. Speedometer (P. 2-2) 4. Fuel gauge (P. 2-2) 2. Vehicle information display (P. 2-4) 5. Warning/indicator lights (P. 2-10) — Rear view monitor* (P. 4-2) 6. Instrument brightness control switch (P. 2-3)/ — Tachometer (P. 2-7) Trip computer mode switch (P. 2-6) — Trip computer (P. 2-6) — Indicators, warnings and alerts (P. 2-4) 7. Trip odometer reset switch (P. 2-2) — Engine oil information (P. 2-9) 8. Upshift indicator (P. 2-5, P. 5-9) 3. Clock (P. 2-27)

0-10 Illustrated table of contents ENGINE COMPARTMENT

10. Battery (P. 8-17) — Jump starting (P. 6-6) 11. Engine coolant reservoir (P. 8-5)

SSI0605

HR16DE ENGINE MODEL 5. Fuse/fusible link holders (P. 8-20) 1. Brake and clutch fluid reservoir (P. 8-13) — 6. Window washer fluid reservoir (P. 8-16) RHD model 7. Engine drive belt location (P. 8-11) 2. Engine oil filler cap (P. 8-7) 8. Engine oil dipstick (P. 8-6) 3. Brake and clutch fluid reservoir (P. 8-13) — 9. Radiator cap (P. 8-5) LHD model — Vehicle overheat (P. 6-7) 4. Air cleaner (P. 8-14)

Illustrated table of contents 0-11 SSI0609

K9K ENGINE MODEL 5. Air cleaner (P. 8-14) 1. Window washer fluid reservoir (P. 8-16) 6. Battery (P. 8-17) 2. Brake and clutch fluid reservoir (P. 8-13) — 7. Engine drive belt location (P. 8-11) RHD model 8. Engine oil dipstick (P. 8-6) 3. Engine oil filler cap (P. 8-7) 9. Engine coolant reservoir (P. 8-5) 4. Brake and clutch fluid reservoir (P. 8-13) — 10. Fuse/Fusible link holders (P. 8-20) LHD model

0-12 Illustrated table of contents 1 Safety — seats, seat belts and supplemental restraint system

Seats...... 1-2 Universal child restraints for front seat and rear Front seats ...... 1-2 seats ...... 1-12 Second row seats (where fitted) ...... 1-3 ISOFIX child restraint system (where fitted) ...... 1-14 Third row seats (where fitted) ...... 1-5 Child restraint anchorage (where fitted) ...... 1-15 Head restraints ...... 1-6 Child restraint installation using ISOFIX ...... 1-16 Seat belts ...... 1-7 Child restraint installation using 3-point type Precautions on seat belt usage ...... 1-7 seat belt ...... 1-18 Child safety ...... 1-8 Supplemental Restraint System (SRS) ...... 1-21 Pregnant women ...... 1-8 Precautions on Supplemental Restraint Injured persons...... 1-9 System (SRS)...... 1-21 Centre mark on seat belts (where fitted) ...... 1-9 Supplemental air bag systems ...... 1-25 Three-point type seat belts...... 1-9 Pre-tensioner seat belt system (where fitted)...... 1-27 Child restraints ...... 1-11 Repair and replacement procedure ...... 1-27 Precautions on child restraint usage...... 1-11 SEATS

SSS0133AZ

FRONT SEATS WARNING • Do not drive and/or ride in the vehicle with WARNING the seatback reclined. This can be danger- Do not adjust the driver’s seat while driving so ous. The shoulder belt will not be properly that full attention may be given to vehicle opera- against the body. In an accident, you and your tion. passengers could be thrown into the shoulder belt and receive neck or other serious Manual seat adjustment injuries. You and your passengers could also slide under the lap belt and receive serious WARNING injuries. After adjusting a seat, gently shake the seat to • For the most effective protection while the confirm that the seat is locked securely. If the vehicle is in motion, the seatback should be seat is not locked securely, it may move sud- upright. Always sit well back in the seat and denly and could cause the loss of control of the adjust the seat belt properly. (See “Seat belts” vehicle. later in this section.) CAUTION When adjusting the seat positions, be sure not to contact any moving parts to avoid possible injuries and/or damages.

1-2 Safety — seats, seat belts and supplemental restraint system the seating position, lift it up to an upright position. Pull the reclining lever and lean the seatback to a proper seating position. CAUTION Do not apply a total load of more than 20 kg (44 lb) to the folded seatback. SECOND ROW SEATS (where fitted) Folding SSS0955Z

WARNING Forward and backward (where fitted): • Be careful not to damage the seat belt while 1. Pull up the adjusting lever j1. folding the second row seats. 2. Slide the seat to the desired position. • Never allow anyone to ride in the luggage area 3. Release the adjusting lever to lock the seat in or on the second row seats when they are in position. the folded position. Use of these areas by passengers without proper restraints could result Reclining: in serious injury in an accident or sudden stop. j 1. Pull up the adjusting lever 2. • Do not fold the second row seats while the 2. Tilt the seatback to the desired position. SSS0956Z vehicle is moving. 3. Release the adjusting lever to lock the seatback • Do not fold the second row seats when occu- in position. Folding front passenger’s seat (where fitted): pants are in the second row seats area or any luggage is on the second row seats. The reclining feature allows the adjustment of the The front passenger’s seatback can be folded down. seatback for occupants of different sizes to help Some long objects may be loaded in the vehicle • Properly secure all luggage to help prevent it obtain the proper seat belt fit. (See “Seats” later in when the second row seats are also folded down. from sliding or shifting. Do not place luggage this section.) (See “Second row seats (where fitted)” later in this higher than the seatbacks. section for folding the second row seats.) The seatback may be reclined to allow occupants to • When returning the seat to the original posi- rest when the vehicle is parked. To fold the front passenger’s seatback, pull the re- tion, be certain they are completely secured clining lever all the way j1. When returning the front passenger’s seatback to

Safety — seats, seat belts and supplemental restraint system 1-3 in the latched position. If they are not com- 1. Move the head restraint to its lowest position. pletely secured, passengers may be injured in 2. Pull the strap j1 and fold the seatback down j2. an accident or sudden stop. 3. Pull the lock strap j3 , and then lift the seat cush- Securely store the removed head restraints to • ion and fold it forward j4. prevent them from being thrown around in case of a sudden stop or accident. 4. Fold the seat leg j5 downward. • Head restraints should be adjusted properly 5. Hang the hook j6 (stored in the back side of the as they may provide significant protection seat cushion) on the head restraint stalk of the against whiplash injury. Always replace and front seat. adjust them properly if they have been re- 6. Adjust the strap if necessary. Pull the adjuster up moved for any reason. to loosen j7 or pull the strap out to tighten j8. CAUTION Do not fold the second row seats when the third row seats are occupied while the vehicle is in motion.

SSS1112

1-4 Safety — seats, seat belts and supplemental restraint system Returning: • Properly secure all luggage to help prevent it from sliding or shifting. Do not place luggage 1. Pull the adjuster j1 up to loosen. higher than the seatbacks. 2. Remove the hook j2 and store it in the pocket on the backside of the seat. • When returning the seatbacks to the upright position, be certain they are completely se- 3. Unfold the seat leg j3 and pull the strap j4to cured in the latched position. If they are not return the seat in position. completely secured, passengers may be in- 4. Pull the strap j5 and unfold the seatback j6 jured in an accident or sudden stop. until it is latched. • Securely store the removed head restraints to THIRD ROW SEATS (where fitted) prevent them from being thrown around in case of a sudden stop or accident. Folding • Head restraints should be adjusted properly CAUTION as they may provide significant protection against whiplash injury. Always replace and Do not use the third row seats with the second adjust them properly if they have been re- row seats folded while the vehicle is in motion. moved for any reason. CAUTION WARNING Make sure the lid of the rear seat cup holders is • Be careful not to damage the seat belt while closed before folding the rear seat back. folding the third row seats. • Never allow anyone to ride in the luggage area or on the third row seats when they are in the fold-down position. Use of these areas by passengers without proper restraints could result in serious injury in an accident or sudden stop. • Do not fold the third row seats while the vehicle is moving. • Do not fold down the third row seatback when occupants are in the third row seat area or any luggage is on the third row seats. SSS0999

Safety — seats, seat belts and supplemental restraint system 1-5 1. Move the head restraint to its lowest position. The proper adjustment of the head restraint is as illustrated. 2. Pull the lever j1 and fold down the seatback. Adjust the head restraint so that the head restraint’s 3. Pull the lever j2 on the back side of the seat leg centre is level with the centre of the ears. to unlatch the seat. 4. Fold the seat to the side j3. 5. Hook the seat hook j4 to the strap on the ceiling securely. 6. Adjust the strap. Pull the adjuster up to loosen j5 , or pull the strap out to tighten j6. 7. Fold the seat leg j7. HEAD RESTRAINTS SSS0288Z

Adjustment (where fitted) 1. Pull up the head restraint to raise to the proper position. 2. Push in the lock knob j1 and push down the head restraint to lower to the proper position. The adjustable rear head restraint should only be SSS0287Z used in the notched stem positions. The lowest head restraint position is the stowed position. WARNING When removing the rear head restraint for seat folding etc., push the lock knob and pull up the head Do not drive and/or ride in the vehicle with the restraint. The removed head restraint should be se- head restraint removed. This can be dangerous. curely stored. Head restraints should be adjusted properly as they may provide significant protection against injury in an accident. Check the height after SSS0959 someone else uses the seat.

1-6 Safety — seats, seat belts and supplemental restraint system SEAT BELTS

PRECAUTIONS ON SEAT BELT USAGE If you are wearing the seat belt properly adjusted and sitting upright and well back in the seat, chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced. NISSAN strongly encourages you and all of your passengers to buckle up every time you drive, even if your seating position includes the supplemental air bag systems. NPA930Z Sit upright and well back. • Never wear seat belts inside out. Belts should WARNING not be worn with straps twisted. Doing so may • Seat belts are designed to bear upon the bony reduce their effectiveness. structure of the body, and should be worn low • Seat belts should be adjusted as firmly as across the front of the pelvis or the pelvis, possible, consistent with comfort, to provide chest and shoulders, as applicable; wearing the protection for which they have been de- the lap section of the belt across the abdomi- signed. A slack belt will greatly reduce the nal area must be avoided. Serious injury may protection afforded to the wearer. occur if a seat belt is not worn properly. • Every person who drives or rides in this ve- • Position the lap belt as low and snug as pos- hicle should use a seat belt at all times. Chil- sible around the hips, not the waist. A lap belt dren should be properly restrained in the rear worn too high could increase the risk of inter- seat and, if appropriate, in a child restraint nal injuries in an accident. system. • Do not allow more than one person to use the • Do not run the belt behind your back or under same seat belt. Each belt assembly must only your arm. Always route the shoulder belt over be used by one occupant; it is dangerous to your shoulder and across your chest. The belt put a belt around a child being carried on the should be away from your face and neck, but occupant’s lap. not falling off your shoulder. Serious injury • Never carry more people in the vehicle than may occur if a seat belt is not worn properly. there are seat belts.

Safety — seats, seat belts and supplemental restraint system 1-7 • No modifications or additions should be made CHILD SAFETY vehicle and the child, and always follow the manu- by the user which will either prevent the seat facturer’s instructions for installation and use. belt adjusting devices from operating to re- WARNING move slack, or prevent the seat belt assembly Large children from being adjusted to remove slack. • Infants and children need special protection. The vehicle’s seat belts may not fit them prop- WARNING • Care should be taken to avoid contamination erly. The shoulder belt may come too close to Never allow children to stand or kneel on any of the webbing with polishes, oils and chemi- the face or neck. The lap belt may not fit over • seats. cals, and particularly battery acid. Cleaning their small hipbones. In an accident, an im- may safely be carried out using mild soap and properly fitted seat belt could cause serious • Never allow children in the cargo areas while water. The belt should be replaced if webbing or fatal injury. the vehicle is moving. A child could be seri- becomes frayed, contaminated or damaged. ously injured in an accident or sudden stop. • Always use an appropriate child restraint sys- • All seat belt assemblies including retractors tem. Children who are too large for a child restraint sys- and attaching hardware should be inspected tem should be seated and restrained by the seat after any collision by a NISSAN dealer or quali- Children need adults to help protect them. They belts that are provided. fied workshop. NISSAN recommends that all need to be properly restrained. The proper restraint seat belt assemblies in use during a collision depends on the child’s size. If the child’s seating position has a shoulder belt that be replaced unless the collision was minor fits close to the face or neck, the use of a booster and the belts show no damage and continue seat (commercially available) may help overcome to operate properly. Seat belt assemblies not this. The booster seat should raise the child so that in use during a collision should also be in- the shoulder belt is properly positioned across the spected and, when necessary, replaced if ei- top, middle portion of the shoulder and the lap belt ther damage or improper operation is noted. is low on the hips. The booster seat should also fit the vehicle seat. Once the child has grown so that • It is essential to replace the entire assembly the shoulder belt is no longer on or near the face or after it has been worn in a severe impact even neck of the child, use the shoulder belt without the if damage to the assembly is not obvious. booster seat. In addition, there are many types of SSS0099Z • Once the pre-tensioner seat belt has acti- child restraint systems available for larger children vated, it cannot be reused. It must be replaced that should be used for maximum protection. together with the retractor. Contact a NISSAN Infants and small children PREGNANT WOMEN dealer or qualified workshop. NISSAN recommends that infants and small chil- NISSAN recommends that pregnant women use • Removal and installation of the pre-tensioner dren be seated in a child restraint system. You seat belts. The seat belt should be worn snug, and seat belt system components should be done should choose a child restraint system that fits your always position the lap belt as low as possible by a NISSAN dealer or qualified workshop. around the hips, not the waist. Place the shoulder

1-8 Safety — seats, seat belts and supplemental restraint system belt over your shoulder and across your chest. Never THREE-POINT TYPE SEAT BELTS den stop or on impact. A slow pulling motion run the lap/shoulder belt over your abdominal area. permits the seat belt to move, and allows you Contact your doctor for specific recommendations. some freedom of movement in the seat. INJURED PERSONS NISSAN recommends that injured persons use seat belts. Contact your doctor for specific recommendations. CENTRE MARK ON SEAT BELTS (where fitted) SSS0292Z

SSS0467Z WARNING Every person who drives or rides in this vehicle 3. Position the lap belt portion low and snug on the should use a seat belt at all times. hips as shown. Fastening seat belts 4. Pull the shoulder belt portion toward the retractor to take up extra slack. Be sure the shoulder WARNING belt is routed over your shoulder and is snug SSS0960Z across your chest. The seatback should not be in a reclined position any more than needed for comfort. Seat belts are Selecting correct set of seat belts most effective when the passenger sits well back The centre seat belt buckle is identified by the CEN- and straight up in the seat. TER mark. The centre seat belt tongue can be fas- 1. Adjust the seat. (See “Seats” earlier in this sec- tened only into the centre seat belt buckle. tion.) 2. Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage. The retractor is designed to lock during a sud- SSS0391Z

Safety — seats, seat belts and supplemental restraint system 1-9 Rear centre seat belt (for second row 2. Insert a suitable tool such as key jA into the connector buckle to release the connector tongue seat - where fitted) j j 1. The rear centre seat belt has a connector tongue 1 j and a seat belt tongue j2 . Both the connector 3. Fold the connector as illustrated 2. tongue and the seat belt tongue must be securely 4. Store the connector tongue into the retractor latched for proper seat belt operation. base j3.

WARNING • Do not unfasten the rear centre seat belt connector except when folding down the rear seat. • When attaching the rear centre seat belt connector, be certain that the seatbacks are completely secured in the latched position and the rear centre seat belt connector is com- SSS0241Z pletely secured. • If the rear centre seat belt connector and the WARNING seatbacks are not secured in the correct position, serious personal injury may result in an • Always fasten the connector tongue and the accident or sudden stop. seat belt in the order shown. SSS1001Z • Always make sure both the connector tongue and the seat belt tongue are secured when using the seat belt. Do not use it with only the Stowing rear centre seat belt: seat belt tongue attached. This could result in When folding down the rear seat, the rear centre serious personal injury in case of an accident seat belt can be retracted into a stowed position. or a sudden stop. 1. Hold the connector tongue j1 so that the seat belt does not retract suddenly when the tongue is released from the connector buckle.

1-10 Safety — seats, seat belts and supplemental restraint system CHILD RESTRAINTS

2. Pull the seat belt and fasten the connector buckle PRECAUTIONS ON CHILD j until it clicks 2. RESTRAINT USAGE The centre seat belt connector tongue can be attached only into the rear centre seat belt connector buckle. To fasten the seat belt, see “Fastening seat belts” earlier in this section.

WARNING When attaching the rear centre seat belt connector, be certain that the seatbacks are completely SSS0099Z secured in the latched position and the rear centre seat belt connector is completely secured. Unfastening seat belts WARNING Infants and small children should always be Push the button on the buckle. The seat belt auto- • placed in an appropriate child restraint while matically retracts. riding in the vehicle. Failure to use a child Checking seat belt operation restraint can result in serious injury or death. Seat belt retractors are designed to lock seat belt • Infants and small children should never be movement: carried on your lap. It is not possible for even the strongest adult to resist the forces of a SSS1005Z When the seat belt is pulled quickly from the • severe accident. The child could be crushed retractor. between the adult and parts of the vehicle. Attaching rear centre seat belt: • When the vehicle slows down rapidly. Also, do not put the same seat belt around both your child and yourself. Always be sure the rear centre seat belt connector To increase your confidence in the seat belts, check tongue and connector buckle are attached. Discon- the operation by grasping the shoulder belt and pull- • NISSAN recommends that the child restraints nect only when folding down the rear seat. ing forward quickly. The retractor should lock and be installed in the rear seat. According to ac- To connect the buckle: restrict further belt movement. If the retractor does cident statistics, children are safer when prop- not lock during this check, contact a NISSAN dealer erly restrained in the rear seat than in the front 1. Pull out the seat belt tongue from the retractor or qualified workshop immediately. seat. base j1.

Safety — seats, seat belts and supplemental restraint system 1-11 • Improper use or improper installation of a • Never install a rear-facing child restraint on • Choose a child restraint that complies with the child restraint can increase the risk or sever- the front passenger’s seat when the front pas- latest European safety standard, ECE Regula- ity of injury for both the child and other occu- senger’s air bag is available. Supplemental tion 44.03. pants of the vehicle and can lead to serious front-impact air bags inflate with great force. Place your child in the child restraint and check injury or death in an accident. A rear-facing child restraint could be struck • the various adjustments to be sure the child re- by the supplemental front-impact air bags in Follow all of the child restraint manufacturer’s straint is compatible with your child. Always fol- • an accident and could seriously injure or kill instructions for installation and use. When low all of the recommended procedures. your child. purchasing a child restraint, be sure to select Check the child restraint in your vehicle to be one which will fit your child and vehicle. It may If the seat belt in the position where a child • • sure it is compatible with vehicle’s seat belt sys- not be possible to properly install some types restraint is installed requires a locking device tem. of child restraint in your vehicle. and if it is not used, injuries could result from a child restraint tipping over during normal Refer to the tables later in this section for a list of The direction of the child restraint, either • • vehicle braking or cornering. the recommended fitment positions and the ap- front-facing or rear-facing, depends on the proved child restraints for your vehicle. type of the child restraint and the size of the CAUTION child. Refer to the child restraint manufactur- Remember that a child restraint left in a closed er’s instructions for details. vehicle can become very hot. Check the seating • Adjustable seatbacks should be positioned to surface and buckles before placing your child in fit the child restraint, but as upright as pos- a child restraint. sible. NISSAN recommends that infants and small chil- • After attaching a child restraint, test it before dren be seated in a child restraint. You should you place the child in it. Push it from side to choose a child restraint that fits your vehicle and side and tug it forward to make sure that it is always follow the manufacturer’s instructions for in- held securely in place. The child restraint stallation and use. In addition, there are many types should not move more than 25 mm (1 in). If of child restraints available for larger children that the restraint is not secure, tighten the belt as should be used for maximum protection. necessary, or install the restraint in another seat and test it again. UNIVERSAL CHILD RESTRAINTS FOR FRONT SEAT AND REAR SEATS • When the child restraint is not in use, keep it secured with the ISOFIX child restraint sys- When selecting any child restraint, keep the follow- tem or a seat belt to prevent it from being ing points in mind: thrown around in case of a sudden stop or accident.

1-12 Safety — seats, seat belts and supplemental restraint system Approved child restraint positions

Seating position Front passenger seat with air bag Front pas- Age group (with 2nd centre senger seat 2nd outer seat 3rd outer seat deactivated seat without air bag front passenger air bag ONLY) Group 0+ <13kg(0to24 L* L* X L* or I* L* months) Group I 9to18kg(9to LLXLorIL 48 months) Group II and III 15 to 36 kg (4 to LLXLL 12 years)

U: Suitable for “Universal” category - front and rear facing child restraints - approved for use in this age group. L: Suitable for particular child restraints given in the following table. I: Suitable for “ISOFIX (with top tether)” category given in the following table. *: Rearward facing only

Safety — seats, seat belts and supplemental restraint system 1-13 List of approved child restraints WARNING Seating position In vehicles equipped with a side air bag system, Front pas- do not let any infants or small children sit in the senger seat front passenger’s seat as the air bag may cause with air bag serious injury in case of deployment during a col- Front pas- Age group (with 2nd centre lision. senger seat 2nd outer seat 3rd outer seat deactivated seat without air bag NOTE front passenger air bag Child restraints approved to ECE Regulation NO. ONLY) 44.03 are clearly marked with the categories such Britax Cosy as Universal, Semi-universal or ISOFIX. Britax Cosy Britax Cosy Tot*1, *2 Britax Cosy Group 0+ ISOFIX CHILD RESTRAINT SYSTEM Tot*1, *2 Tot*1, *2 Romer Baby- Tot*1, *2 <13kg(0to24 — Romer Baby- Romer Baby- Safe*1, *2 Romer Baby- (where fitted) months) Safe*1, *2 Safe*1, *2 Fair G 0/1*2, Safe*1, *2 *3 Group I Britax/Romer Britax/Romer Britax/Romer Britax/Romer 9to18kg(9to — Duo Plus*1 Duo Plus*1 Duo Plus*1 Duo Plus*1 48 months) Fair G 0/1*3 Group II and III Britax Hi Britax Hi Britax Hi Britax Hi 15 to 36 kg (4 to Liner*1 Liner*1 — Liner*1 Liner*1 12 years) Romer Kid*1 Romer Kid*1 Romer Kid*1 Romer Kid*1

*1: Universal mode only. SSS0998Z *2: Rearward facing only. ISOFIX label location *3: This is an ISOFIX child restraint. It requires an additional platform to be fitted to your vehicle: Your vehicle is equipped with special anchor points Rearward facing use Platform RWF D Forward facing use Platform FWF B that are used with ISOFIX child restraint systems. Alternatively, refer to a NISSAN dealer or qualified workshop for the latest platform references.

1-14 Safety — seats, seat belts and supplemental restraint system ISOFIX lower anchor point locations CHILD RESTRAINT ANCHORAGE The ISOFIX anchor points are provided to install (where fitted) child restraints in the second row outer seating po- Your vehicle is designed to accommodate a child sitions only. Do not attempt to install a child re- restraint system on the second row seat. When in- straint in the centre position using the ISOFIX stalling a child restraint system, carefully read and anchors. follow the instructions in this manual and those supplied with the child restraint system.

WARNING SSS0644Z Anchor attachment Child restraint anchorages are designed to withstand only those loads imposed by correctly fit- ISOFIX child restraint anchor ted child restraints. Under no circumstances are attachments they to be used for adult seat belts, harnesses or for attaching other items or equipment to the ISOFIX child restraints include two rigid attach- vehicle. SSS0637Z ments that can be connected to two anchors located in the seat. With this system, you do not have ISOFIX lower anchor location to use a vehicle seat belt to secure the child re- The ISOFIX anchors are located at the rear of the straint. Check your child restraint for a label stating seat cushion near the seatback. A label is attached that it is compatible with the ISOFIX child restraints. to the seatback to help you locate the ISOFIX an- This information may also be in the instructions pro- chors. vided by the child restraint manufacturer. ISOFIX child restraints generally require the use of a top tether strap or other anti-rotation devices such as support legs. When installing ISOFIX child restraints, carefully read and follow the instructions in SSS1000Z this manual and those supplied with the child restraints. (See “Child restraint installation using Anchorage location ISOFIX” later in this section.) The anchor points are located on the seat cushion behind the second row outer seating positions.

Safety — seats, seat belts and supplemental restraint system 1-15 CHILD RESTRAINT INSTALLATION USING ISOFIX

WARNING • Attach ISOFIX child restraints only at the specified locations. For the ISOFIX lower anchor locations, see “ISOFIX child restraint system (where fitted)” earlier in this section. If a child restraint is not secured properly, your child could be seriously injured or killed in an SSS0646AZ SSS0754AZ accident. Steps 1 and 2 Step 4 • Do not install child restraints that require the Installation on second row outer seats 4. Shorten the rigid attachment to have the child restraint firmly tightened; press downward j3 use of a top tether strap to seating positions Front-facing: j that do not have a top tether anchor. and rearward 4 firmly in the centre of the child Be sure to follow the manufacturer’s instructions for restraint with your knee to compress the vehicle • Do not secure a child restraint in the centre the proper use of your child restraint. Follow these seat cushion and seatback. second row and third row seating positions steps to install a front-facing child restraint on the 5. If the child restraint is equipped with a top tether using the ISOFIX lower anchors. The child re- second row outer seats using ISOFIX: straint will not be secured properly. strap, route the top tether strap and secure the 1. Position the child restraint on the seat j1. tether strap to the tether anchor point. (See • Inspect the lower anchors by inserting your “Child restraint anchorage (where fitted)” earlier 2. Secure the child restraint anchor attachments to fingers into the lower anchor area and feeling j in this section.) to make sure there are no obstructions over the ISOFIX lower anchors 2. 6. If the child restraint is equipped with other anti- the ISOFIX anchors, such as seat belt web- 3. The back of the child restraint should be secured rotation devices such as support legs, use them bing or seat cushion material. The child re- against the vehicle seatback. If necessary, adjust instead of the top tether strap following the child straint will not be secured properly if the or remove the head restraint to obtain the correct restraint manufacturer’s instructions. ISOFIX anchors are obstructed. child restraint fit. (See “Head restraints” earlier in • Child restraint anchorages are designed to this section.) If the head restraint is removed, withstand only those loads imposed by cor- store it in a secure place. Be sure to install the rectly fitted child restraints. Under no circum- head restraint when the child restraint is stance are they to be used for adult seat belts, removed. If the seating position does not have an harnesses or for attaching other items or adjustable head restraint and it is interfering with equipment to the vehicle. the proper child restraint fit, try another seating position or a different child restraint.

1-16 Safety — seats, seat belts and supplemental restraint system Rear-facing: rotation devices such as support legs, use them Be sure to follow the manufacturer’s instructions for instead of the top tether strap following the child the proper use of your child restraint. Follow these restraint manufacturer’s instructions. steps to install a rear-facing child restraint on the rear outer seats using ISOFIX: 1. Position the child restraint on the seat j1. 2. Secure the child restraint anchor attachments to the ISOFIX lower anchors j2.

SSS0755AZ Step 7 7. Test the child restraint before you place the child SSS0757AZ in it j5 . Push the child restraint from side to side and tug it forward to make sure that it is held Step 6 securely in place. 6. Test the child restraint before you place the child in it j5 . Push the child restraint from side to side 8. Check to make sure that the child restraint is and tug it forward to make sure that it is held properly secured prior to each use. If the child securely in place. restraint is loose, repeat steps 3 through 7. SSS0756AZ 7. Check to make sure that the child restraint is Step 3 properly secured prior to each use. If the child 3. Shorten the rigid attachment to have the child restraint is loose, repeat steps 3 through 6. restraint firmly tightened; press downward j3 and rearward j4 firmly in the centre of the child restraint with your hand to compress the vehicle seat cushion and seatback. 4. If the child restraint is equipped with a top tether strap, route the top tether strap and secure the

SSS0649AZ tether strap to the tether anchor point. (See Steps 1 and 2 “Child restraint anchorage (where fitted)” earlier in this section.) 5. If the child restraint is equipped with other anti-

Safety — seats, seat belts and supplemental restraint system 1-17 CHILD RESTRAINT INSTALLATION press downward j3 and rearward j4 firmly in USING 3-POINT TYPE SEAT BELT the centre of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt.

SSS0493AZ Step 2 SSS0758AZ 2. Route the seat belt tongue through the child re- Step 1 straint and insert it into the buckle j2 until you SSS0638AZ hear and feel the latch engage. Installation on rear seats Step 5 3. To prevent slack in the seat belt webbing, it is Front-facing: 5. Test the child restraint before you place the child necessary to secure the seat belt in place with in it j5 . Push the child restraint from side to side Be sure to follow the manufacturer’s instructions for locking devices attached to the child restraint. the proper use of your child restraint. Follow these and tug it forward to make sure that it is held steps to install a front-facing child restraint on the securely in place. rear seats using 3-point type seat belt without auto- 6. Check to make sure that the child restraint is matic locking mode: properly secured prior to each use. If the child 1. Position the child restraint on the seat j1. restraint is loose, repeat steps 3 through 5.

SSS0647AZ Step 4 4. Remove any additional slack from the seat belt;

1-18 Safety — seats, seat belts and supplemental restraint system 2. Route the seat belt tongue through the child restraint and insert it into the buckle j2 until you hear and feel the latch engage. 3. To prevent slack in the seat belt webbing, it is necessary to secure the seat belt in place with locking devices attached to the child restraint.

SSS0759AZ SSS0658AZ Step 1 Step 5 Rear-facing: 5. Test the child restraint before you place the child j Be sure to follow the manufacturer’s instructions for in it 5 . Push the child restraint from side to side the proper use of your child restraint. Follow these and tug it forward to make sure that it is held steps to install a rear-facing child restraint on the securely in place. SSS0639AZ rear seats using 3-point type seat belt without auto- 6. Check to make sure that the child restraint is matic locking mode: Step 4 properly secured prior to each use. If the child 1. Position the child restraint on the seat j1. 4. Remove any additional slack from the seat belt; restraint is loose, repeat steps 3 through 5. press downward j3 and rearward j4 firmly in the centre of the child restraint with your hand to compress the vehicle seat cushion and seatback while pulling up on the seat belt.

SSS0654AZ Step 2

Safety — seats, seat belts and supplemental restraint system 1-19 If you must install a front-facing child restraint system on the front seat, follow these steps: 1. For models with the supplemental front-impact passenger’s air bag, turn off the front passenger’s air bag using the front passenger air bag switch. (See “Supplemental air bag systems” later in this section.) Turn the ignition switch to the ON position and make sure that the front air bag status light on the instrument panel illu- SSS0300AZ minates. 2. Move the seat to the rearmost position j1. Installation on front passenger’s seat not be used on the front passenger’s seat 3. Adjust the head restraint to its highest position when the front passenger’s air bag is avail- j2. WARNING able. 4. Position the child restraint in the seat. • Never install a rear-facing child restraint on the front passenger’s seat when the front passenger’s air bag is available. Supplemental front-impact air bags inflate with great force. A rear-facing child restraint could be struck by the supplemental front-impact air bags in an accident and could seriously injure or kill your child. Never install a child restraint with a top tether • SSS0627Z strap on the front seat. Steps 2 and 3 SSS0360CZ Step 5 • NISSAN recommends that a child restraint be Front-facing: installed on the rear seat. However, if you 5. Route the seat belt tongue through the child re- must install a child restraint on the front pas- Be sure to follow the manufacturer’s instructions for straint and insert it into the buckle j3 until you senger’s seat, move the passenger’s seat to the proper use of your child restraint. Follow these hear and feel the latch engage. the rearmost position. steps to install a front-facing child restraint on the front passenger’s seat using 3-point type seat belt 6. To prevent slack in the seat belt webbing, it is • Child restraints for infants must be used in without automatic locking mode: necessary to secure the seat belt in place with the rear-facing direction and therefore must locking devices attached to the child restraint.

1-20 Safety — seats, seat belts and supplemental restraint system SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

9. Check to make sure that the child restraint is PRECAUTIONS ON SUPPLEMENTAL properly secured prior to each use. If the child RESTRAINT SYSTEM (SRS) restraint is loose, repeat steps 6 through 8. This Supplemental Restraint System (SRS) section contains important information concerning the driver’s and passenger’s supplemental front-impact air bags, supplemental side-impact air bags and pre- tensioner seat belts. Supplemental front-impact air bag SSS0647BZ system Step 7 This system can help cushion the impact force to 7. Remove any additional slack from the seat belt; the head and chest area of the driver and/or front press downward j4 and rearward j5 firmly in passenger (where fitted) in certain frontal collisions. the centre of the child restraint with your knee to The supplemental front-impact air bag is designed compress the vehicle seat cushion and seatback to inflate on the front where the vehicle is impacted. while pulling up on the seat belt. Supplemental side-impact air bag system (where fitted) This system can help cushion the impact force to the chest area of the driver and front passenger in certain side-impact collisions. The supplemental side-impact air bag is designed to inflate on the side where the vehicle is impacted. The SRS is designed to supplement the accident protection provided by the driver’s and passenger’s SSS0302GZ seat belts and is not designed to substitute for Step 8 them. The SRS can help save lives and reduce serious injuries. However, inflating air bags may cause 8. Test the child restraint before you place the child abrasions or other injuries. Air bags do not provide in it j6 . Push the child restraint from side to side protection to the lower body. Seat belts should al- and tug it forward to make sure that it is held ways be correctly worn and the occupants should securely in place. always be seated a suitable distance away from the steering wheel and instrument panel. (See “Seat

Safety — seats, seat belts and supplemental restraint system 1-21 belts” earlier in this section). The air bags inflate quickly in order to help protect the occupants. The force of the air bags inflating can increase the risk of injury if the occupants are too close to, or are against, the air bag modules during inflation. The air bags will deflate quickly after deployment. The SRS operates only when the ignition switch is in the ON or START position. When the ignition switch is in the ON position, the SRS air bag warning light illuminates for NPA930Z about 7 seconds and then turns off. This indi- Sit upright and well back cates that the SRS air bag system is operational. against the seatback and as far away as prac- (See “SRS air bag warning light” later in this sec- WARNING tical from the steering wheel or instrument tion.) • The supplemental front-impact air bags ordi- panel. Always use the seat belts. narily will not inflate in the event of a side impact, rear impact, rollover, or lower severity frontal collision. Always wear the seat belts to help reduce the risk or severity of injury in accidents. • The seat belts and the supplemental front-impact air bags are most effective when you are sitting well back and upright in the seat. The front-impact air bags inflate with great force. If you and your passengers are unrestrained, NPA926Z leaning forward, sitting sideways, or out of Correct (rear) seating positions position in any way, you and your passengers are at greater risk of injury or death in an acci- WARNING dent. You and your passengers may also receive serious or fatal injuries from the supple- • Never let children ride unrestrained or extend mental front-impact air bag if you are up their hands or face out of the window. Do not against it when it inflates. Always sit back attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.

1-22 Safety — seats, seat belts and supplemental restraint system • Children may be severely injured or killed supplemental side-impact air bags inflate with when the supplemental front-impact air bags, great force. If you and your passengers are supplemental side-impact air bags, or supple- unrestrained, leaning forward, sitting side- mental curtain side-impact air bags inflate if ways, or out of position in any way, you and they are not properly restrained. your passengers are at greater risk of injury or death in an accident. • Do not allow anyone to place their hands, legs, or face near the supplemental side-impact air bags on the sides of the seatback of the front

seats. Do not allow anyone sitting in the front SSS1029Z seats to extend their hands out of the windows or lean against the doors. Some examples of dangerous riding positions are Air bag warning labels shown in the illustrations. Warning labels about the supplemental air bag sys- SSS0100Z • When sitting in the rear seats, do not hold tem are placed in the vehicle as shown in the illus- onto the seatback of the front seats. If the tration. • Never install a rear-facing child restraint sys- supplemental side-impact air bags inflate, you SRS air bag: tem on the front seat. An inflating supplemen- may be seriously injured. Be especially care- The warning label j1 is located on the surface of tal front-impact air bag could seriously injure ful with children, who should always be prop- the passenger’s sun visor. or kill your child. (See “Child restraints” ear- erly restrained. SRS front-impact passenger air bag (where fit- lier in this section.) Do not use seat covers on the front seatbacks. • ted): They may interfere with the supplemental WARNING side-impact air bag inflations. The warning label j2 is located on the side of the passenger’s side instrument panel. • The supplemental side-impact air bags Pre-tensioner seat belt system (where fitted) ordinarily will not inflate in the This label warns you not to fit a rear-facing child event of a front impact, rear impact, rollover, The pre-tensioner seat belt system activates in con- restraint system on the front passenger seat as such or lower severity side collision. Always wear junction with the supplemental front-impact air bag. a restraint system used in this position could cause the seat belts to help reduce the risk or sever- Working with the seat belt retractor and anchor, it serious injury to the infant in case of air bag deploy- ity of injury in accidents. helps tighten the seat belt the instant the vehicle ment during a collision. becomes involved in certain types of collisions, help- • The seat belts and the supplemental side-im- ing to restrain front seat occupants. (See “Pre- In vehicles equipped with a front-impact passenger pact air bags are most effective when you are tensioner seat belt system” later in this section.) air bag system, use a rear-facing child restraint sys- sitting well back and upright in the seat. The tem only on the rear seats.

Safety — seats, seat belts and supplemental restraint system 1-23 “Extreme Hazard! Do not use a rearward facing child for about 7 seconds and then turns off. This indi- restraint on a seat protected by an air bag in front of cates that the SRS air bag systems are operational. it!” If any of the following conditions occur, the air bag When installing a child restraint system in your ve- and/or pre-tensioner seat belt systems need servic- hicle, always follow the child restraint system manu- ing: facturer’s instructions for installation. • The SRS air bag warning light remains on after For additional information, see “Child restraints” approximately 7 seconds. earlier in this section. • The SRS air bag warning light flashes intermit- tently. • The SRS air bag warning light does not illuminate at all. Under these conditions, the supplemental front-impact air bag, supplemental side-impact air bag, or pre-tensioner seat belt systems may not operate properly. They must be checked and repaired. Con- tact a NISSAN dealer or qualified workshop imme-

SPA1097Z diately.

SRS air bag warning light The SRS air bag warning light, displaying in the instrument panel, monitors the circuits of the supplemental front-impact air bag, supplemental side-impact air bag and pre-tensioner seat belt systems. The circuits monitored by the SRS air bag warning light are the diagnosis sensor unit, crash zone sensor, satellite sensors, front-impact air bag modules, side-impact air bag modules, pre- tensioner seat belts and all related wiring. When the ignition switch is in the ON or START position, the SRS air bag warning light illuminates

1-24 Safety — seats, seat belts and supplemental restraint system pants and the steering wheel pad, on the instrument panel and the front seats. Such objects may become dangerous projectiles and cause injury if a supplemental air bag inflates. • Immediately after inflation, several supplemental air bag system components will be hot. Do not touch them: you may severely burn yourself. • No unauthorised changes should be made to any components or wiring of the supplemental air bag systems. This is to prevent accidental inflation of the supplemental air bags or damage to the supplemental air bag systems. • Do not make unauthorised changes to your vehicle’s electrical system, suspension system, front end structure, and side panels. This could affect proper operation of the supplemental air bag systems. • Tampering with the supplemental air bag systems may result in serious personal injury.

SSS0705 Tampering includes changes to the steering wheel and the instrument panel by placing materials over the steering wheel pad and 1. Crash zone sensor 6. Seat belt pre-tensioner retractors above, around or on the instrument panel or 2. Supplemental front-impact air bag modules SUPPLEMENTAL AIR BAG SYSTEMS by installing additional trim materials around (Driver’s and front passenger’s) (where fitted) the supplemental air bag systems. 3. Supplemental side-impact air bag modules WARNING • Work around and on the supplemental air bag (where fitted) Do not place any objects on the steering wheel systems should be done by a NISSAN dealer • or qualified workshop. The SRS wiring should 4. Diagnosis sensor unit pad, the instrument panel and the front seats. Do not place any objects between any occu- not be modified or disconnected. Unautho- 5 Satellite sensors (where fitted)

Safety — seats, seat belts and supplemental restraint system 1-25 rised electrical test equipment and probing • The front passenger air bag status light re- devices should not be used on the supple- mains on after approximately 7 seconds. mental air bag systems. • The front passenger air bag status light does • The SRS wiring harness connectors are yel- not illuminate at all. low and/or orange for easy identification. Unless checked and repaired, the front passen- When the air bags inflate, a fairly loud noise may be ger air bag system may not function properly. heard, followed by the release of smoke. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of a breath- SSS0909Z ing condition should get fresh air promptly. Front passenger air bag status light (where fit- Supplemental front-impact air bag ted): system When the ignition switch is in the ON position, the The driver’s supplemental front-impact air bag is front passenger air bag status light on the instru- located at the centre of the steering wheel. The pas- ment panel illuminates for about 7 seconds and then SSS1004Z senger’s supplemental front-impact air bag (if turns off. This indicates that the front passenger air equipped) is located at the instrument panel above bag system is operational. the glove box. Front passenger air bag switch (where fitted): When the front passenger air bag is turned off with The front passenger air bag can be turned off with The supplemental front-impact air bag system is de- the front passenger air bag switch, the front pas- j signed to inflate in higher severity frontal collisions, senger air bag status light will illuminate and remain the front passenger air bag switch A located on although it may inflate if the forces in another type of on as long as the front passenger air bag switch is the side of the instrument panel on the front passen- collision are similar to those of a higher severity fron- in the OFF position. ger’s side. tal impact. It may not inflate in certain frontal colli- To turn off the front passenger air bag: sions. Vehicle damage (or lack of it) is not always an WARNING indication of proper supplemental front-impact air 1. Turn the ignition switch to the “OFF” position. bag system operation. If any of the following conditions occur after the 2. Insert the key into the front passenger air bag ignition switch is turned to the ON position, have switch. For Intelligent Key equipped models, see the system checked, and if necessary repaired, “Keys” in the “3. Pre-driving checks and by a NISSAN dealer or qualified workshop adjustments” section for mechanical key usage. promptly. 3. Push and turn the key to the OFF position.

1-26 Safety — seats, seat belts and supplemental restraint system 4. Turn the ignition switch to the ON position. The collision are similar to those of a higher severity side • If you need to dispose of the pre-tensioner front passenger air bag status light will illuminate impact. It may not inflate in certain side collisions. seat belt system, or scrap the vehicle, contact and remain on. Vehicle damage (or lack of it) is not always an indi- a NISSAN dealer or qualified workshop. Cor- cation of proper supplemental side-impact air bag rect pre-tensioner disposal procedures are To turn on the front passenger air bag: system operation. set forth in the appropriate NISSAN Service 1. Turn the ignition switch to the “OFF” position. Manual. Incorrect disposal procedures could PRE-TENSIONER SEAT BELT cause personal injury. 2. Insert the key into the front passenger air bag SYSTEM (where fitted) switch. The pre-tensioner is encased with the front seat belt’s retractor and anchor. These seat belts are 3. Push and turn the key to the ON position. WARNING used the same as conventional seat belts. 4. Turn the ignition switch to the ON position. The The pre-tensioner seat belt cannot be reused • When the pre-tensioner seat belt activates, a fairly front passenger air bag status light will illuminate after activation. It must be replaced together loud noise may be heard, followed by the release of then turn off. with the retractor and buckle as a unit. smoke. This smoke is not harmful and does not indi- • If the vehicle becomes involved in a collision cate a fire. Care should be taken not to inhale it, as but the pre-tensioner is not activated, be sure it may cause irritation and choking. Those with a his- to have the pre-tensioner system checked tory of a breathing condition should get fresh air and, if necessary, replaced by a NISSAN promptly. dealer or qualified workshop. REPAIR AND REPLACEMENT • No unauthorised changes should be made to PROCEDURE any components or wiring of the pre-tensioner seat belt system. This is to prevent accidental WARNING activation of the pre-tensioner seat belt or SSS0711Z damage to the pre-tensioner seat belt sys- • Once the air bags have been inflated, the air tem. bag modules will not function and must be replaced. The air bag modules must be re- Supplemental side-impact air bag Work around or on the pre-tensioner seat belt • placed by a NISSAN dealer or qualified work- system should be done by a NISSAN dealer or system (where fitted) shop. The inflated air bag modules cannot be qualified workshop. The SRS wiring should The supplemental side-impact air bag is located at repaired. not be modified or disconnected. Unautho- the outside of the front seats’ seatbacks. rised electrical test equipment and probing • The air bag systems should be inspected by a The supplemental side-impact air bag system is de- devices should not be used on the pre-ten- NISSAN dealer or qualified workshop if there signed to inflate in higher severity side collisions, sioner seat belt system. is any damage to the front end portion of the although it may inflate if the forces in another type of vehicle.

Safety — seats, seat belts and supplemental restraint system 1-27 • If you need to dispose of the SRS or scrap the vehicle, contact a NISSAN dealer or qualified workshop. Correct disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury. The air bags and pre-tensioner seat belts are designed to activate on a one-time-only basis. As a reminder, unless the SRS air bag warning light is damaged, the SRS air bag warning light remains illuminated after inflation has occurred. The repair and replacement of the SRS should be done only by a NISSAN dealer or qualified workshop. When maintenance work is required on the vehicle, information about the air bags, pre-tensioner seat belts and related parts should be pointed out to the person performing the maintenance. The ignition switch should always be in the LOCK position when working under the bonnet or inside the vehicle.

1-28 Safety — seats, seat belts and supplemental restraint system 2 Instruments and controls

Meters and gauges...... 2-2 Defogger switch (where fitted)...... 2-24 Speedometer...... 2-2 Hazard indicator flasher switch ...... 2-24 Odometer...... 2-2 Horn...... 2-25 Fuel gauge ...... 2-2 Windows ...... 2-25 Instrument brightness control...... 2-3 Manual windows (where fitted) ...... 2-25 Vehicle information display...... 2-4 Sliding windows (where fitted) ...... 2-25 Indicators for operation (for model with Power windows (where fitted)...... 2-25 Intelligent Key system) ...... 2-4 Clock ...... 2-27 Warnings and alerts...... 2-5 Adjusting time...... 2-27 Indicators for maintenance...... 2-6 Power outlet ...... 2-27 Trip computer...... 2-6 Ashtray ...... 2-28 Engine oil level information display ...... 2-9 Storage ...... 2-28 Warning/indicator lights and audible reminders ...... 2-10 Glove box...... 2-28 Checking bulbs ...... 2-10 Console box ...... 2-29 Warning lights ...... 2-11 Under-seat tray (where fitted)...... 2-29 Indicator lights ...... 2-14 Bottle holders (where fitted)...... 2-29 Audible reminders...... 2-16 Cup holders ...... 2-29 Headlight and turn signal switch...... 2-17 Personal table (where fitted) ...... 2-30 Headlight switch...... 2-17 Hooks ...... 2-30 Headlight aiming control ...... 2-18 Card holder ...... 2-31 Battery saver system...... 2-20 Ticket holders...... 2-31 Turn signal switch...... 2-21 Utility hook...... 2-31 Fog light switch ...... 2-21 Luggage hooks...... 2-32 Front fog lights (where fitted)...... 2-21 Tonneau cover (where fitted) ...... 2-32 Rear fog light...... 2-21 Partition (where fitted)...... 2-33 Wiper and washer switch ...... 2-22 Sun visors ...... 2-33 Windscreen wiper and washer switch...... 2-22 Interior lights...... 2-34 Rain-sensing auto wiper system (where fitted)..... 2-23 Room light ...... 2-34 Rear window wiper and washer switch (where Luggage compartment light ...... 2-34 fitted)...... 2-23 METERS AND GAUGES

For an overview of the instruments and controls The twin trip odometer j2 displays the distance of see “Meters and gauges” in the “0. Illustrated individual trips. table of contents” section. Changing twin trip odometer display: SPEEDOMETER Push the reset switch j3 to change the display as follows: TRIP A → TRIP B → TRIP A Resetting twin trip odometer: Push the reset switch j3 for more than 1 second to SIC4270Z reset the trip odometer to zero. Type C The speedometer indicates the vehicle speed (km/h FUEL GAUGE or MPH). SIC4195Z ODOMETER Type A

SIC4198Z

The fuel gauge jA on the vehicle information display SIC4197Z indicates the approximate fuel level in the tank when SIC4486Z the ignition switch is in the ON position. Type B Odometer/Twin trip odometer The gauge may move slightly during braking, turn- The odometer/twin trip odometer is displayed when ing, accelerating, or going up and down hills due to the ignition switch is in the ON position. movement of fuel in the tank. The odometer j1 displays the total distance the The fuel gauge indicator jB changes to the low fuel vehicle has been driven. warning jC when the fuel level in the tank is getting

2-2 Instruments and controls low. Refuel as soon as it is convenient, preferably INSTRUMENT BRIGHTNESS When the brightness level reaches the maximum or before the gauge reads the empty (0) level. CONTROL minimum, a beep will sound. The arrow, , indicates the fuel filler lid is lo- The vehicle information display shows the bright- cated on the right side of the vehicle. ness level j2. CAUTION The display returns to the normal display when the instrument brightness control switch is not operated Refuel before the gauge reads the empty (0) po- for more than 5 seconds. sition. The instrument brightness level will not be displayed There is a small reserve of fuel in the tank when the and the control switch cannot be operated when the fuel gauge reads the empty (0) position. alert or maintenance information is displayed in the vehicle information display.

SIC4199

The instrument brightness control switch can be operated when the ignition switch and the headlight switch are in the ON position. Turn the control j1 to brighten or dim the meter panel lights.

Instruments and controls 2-3 VEHICLE INFORMATION DISPLAY

• Instrument brightness control (See “Instrument 1. [NO KEY] warning brightness control” earlier in this section.) This warning appears in either of the following con- • Rear view monitor (where fitted) (See “Rear view ditions. monitor (where fitted)” in the “4. Display screen, No key inside the vehicle: heater and air conditioner, and audio system” section.) The warning appears when the door is closed with the key left outside the vehicle and the ignition switch INDICATORS FOR OPERATION (for in the ACC or ON position. Make sure that the key model with Intelligent Key system) is inside the vehicle. SIC4196Z Unregistered key: The warning appears when the ignition switch is The vehicle information display j1 displays the fol- turned from the LOCK position and the key cannot lowing items: be recognised by the system. You cannot start the • Indicators for operation (for model with Intelli- engine with an unregistered key. Use the registered gent Key system) key. • Warnings and alerts 2. Key battery discharge indicator • Indicators for maintenance This indicator appears when the key battery is running out of power. • Trip computer If this indicator appears, replace the battery with a • Setting new one. (See “Intelligent key battery” in the • Clock “8. Maintenance and do-it-yourself” section.) • Upshift indicator (See “Driving vehicle” in the 3. LOCK warning “5. Starting and driving” section.) The warning appears when the ignition switch is left • Engine oil level information in the ACC or “OFF” position instead of completely being turned to the LOCK position. • Odometer (See “Odometer” earlier in this section.) If this warning appears, turn the ignition switch to the LOCK position while pushing the PUSH release • Fuel gauge (See “Fuel gauge” earlier in this sec- button. tion.) SIC4212 The warning will turn off in approximately 5 minutes.

2-4 Instruments and controls At the same time, the Intelligent Key lock warning 1. Parking brake release warning 6. Idling alert light in the meter will blink for approximately 5 minutes and then turn off. This warning appears when the vehicle speed is This alert appears when the set idling time is above 7 km/h (4 MPH) and the parking brake is reached. The time can be set in the setting menu. WARNINGS AND ALERTS applied. (See “Trip computer” later in this section.) 2. Low fuel warning 7. Upshift indicator This warning appears when the fuel level in the tank This indicator appears when the set engine speed is getting low. Refuel as soon as it is convenient, (RPM) for upshift is reached. The speed can be set preferably before the fuel gauge reaches the empty in the setting menu. (See “Trip computer” later in (0) position. this section and “Driving vehicle” in the “5. Starting and driving” section.) There is a small reserve of fuel remaining in the tank when the fuel gauge reaches the empty (0) position. 3. Door open warning This warning appears if any of the doors (including the back door) are open or not closed securely. The vehicle icon indicates which door is open on the display. 4. Time alert This alert appears when the set time is reached. You can set the time for up to 6 hours in the setting menu. (See “Trip computer” later in this section.) 5. Speed alert

SIC4213 This alert appears when the set speed is reached. The speed can be set in the setting menu. (See “Trip computer” later in this section.) The display The design of the warnings and alerts may differ may differ from the speedometer indication. depending on the model.

Instruments and controls 2-5 INDICATORS FOR MAINTENANCE 1. [ENGINE OIL] replacement indicator TRIP COMPUTER This indicator appears when the set time comes for changing the engine oil. You can set or reset the distance for changing the engine oil. 2. [OIL FILTER] replacement indicator This indicator appears when the set time comes for replacing the oil filter. You can set or reset the distance for replacing the oil filter. 3. [TIRE] replacement indicator SIC4215Z This indicator appears when the set time comes for replacing tyres. You can set or reset the distance for To operate the trip computer, push the mode switch replacing tyres. jA. 4. [OTHER] indicator Each time the switch jA is pushed, the display will This indicator appears when the set time comes for change as follows: replacing items other than the engine oil, oil filter Tachometer → Current fuel consumption → Aver- and tyres. You can set or reset the distance for age fuel consumption and speed → Elapsed time replacing the items. and trip odometer → Distance to empty → Setting The design of each display may differ depending on the model.

SIC4214

The design of the indicators may differ depending on the model. See “Trip computer” later in this section for the setting of each indicator.

2-6 Instruments and controls Average fuel consumption (l (litre)/100 km or MPG) and speed (km/h or MPH) Fuel consumption: The average fuel consumption mode shows the average fuel consumption since the last reset. Reset- ting is done by pushing the mode switch jAfor longer than 1 second. (The average speed is also reset at the same time.)

SIC4216Z SIC4241Z The display is updated every 30 seconds. At about Petrol engine model the first 1/3 mile (500 m) after a reset, the display shows “——”. Current fuel consumption (l (litre)/100 km or MPG) Speed: The average speed mode shows the average ve- The current fuel consumption mode shows the cur- hicle speed since the last reset. Resetting is done rent fuel consumption. by pushing the mode switch jA for longer than 1 second. (The average fuel consumption is also reset at the same time.) The display is updated every 30 seconds. The first 30 seconds after a reset, the display shows “——”. SIC4485Z Diesel engine model Tachometer The tachometer indicates the engine speed in revo- lutions per minute (rpm). Do not rev the engine SIC4242Z into the red zone j1. The red zone varies depending on the model.

Instruments and controls 2-7 SIC4243Z SIC4484Z SIC4218Z

Elapsed time and trip odometer (km or Distance to empty (km or MILES) [Setting] MILES) The distance to empty (dte) mode provides you with Setting cannot be made while driving. A mes- Elapsed time: an estimation of the distance that can be driven sage is also displayed on the vehicle information before refuelling. The dte is constantly being calcu- display. The elapsed time mode shows the time since the lated, based on the amount of fuel in the fuel tank last reset. The displayed time can be reset by push- Select a menu by rotating the mode switch jA , then and the actual fuel consumption. ing the mode switch jA for longer than 1 second. push it to set the menu in the setting mode. (The trip odometer is also reset at the same time.) The display is updated every 30 seconds. [ALERT]: Trip odometer: When the fuel level drops even lower, the dte dis- Alert can be set to notify the following items. The trip odometer mode shows the total distance play will change to “----”. • [TIMER] the vehicle has been driven since the last reset. • If the amount of fuel added is small, the display Resetting is done by pushing the mode switch jA just before the ignition switch is turned to the Select this submenu to set the time alert. for longer than 1 second. (The elapsed time is also “OFF” position may continue to be displayed. [SPEED] reset at the same time.) • • When driving uphill or rounding curves, the fuel Select this submenu to set a vehicle speed alert. in the tank shifts, which may momentarily change the display. • [IDLING] Select this submenu to set an idling time alert.

2-8 Instruments and controls • [UPSHIFT] • [12h, 24h] ENGINE OIL LEVEL INFORMATION Select this submenu to set the engine speed Select this submenu to set the 12h/24h time dis- DISPLAY (RPM) of the upshift indicator. (See “Driving play mode. vehicle” in the “5. Starting and driving” section.) • [SETTING] To return to the top page of the setting mode, select Adjust the time (hour and minute) of the clock on [BACK]. the meter. [MAINTENANCE]: • [DISPLAY] The maintenance intervals of the following items can be set or reset for the reminders. Select this submenu to set the clock display to ON/OFF. • [ENGINE OIL] To return to the top page of the setting mode, select SIC4217Z Select this submenu to set or reset the distance [BACK]. for changing the engine oil. [OPTIONS] (where fitted): When the ignition switch is turned to the ON posi- [OIL FILTER] • The following items can be set to your preference. tion, the engine oil level information will be displayed Select this submenu to set or reset the distance as follows: • [LANGUAGE] for replacing the oil filter. [OIL LEVEL GOOD] j1:Oil level is sufficient for Select this submenu to choose the language for [TIRE] driving and the oil level will be displayed. • the display. Select this submenu to set or reset the distance [OIL LEVEL LOW] j2:Oil level is low. Oil needs to [UNIT] for replacing tyres. • be added immediately. Select this submenu to choose the unit (km/l, [OTHER] CAUTION • l/100 km, etc.) for the display. Select this submenu and set or reset the dis- The engine oil level should be checked regularly. To return to the top page of the setting mode, select tance for replacing items other than the engine Operating with an insufficient amount of oil can [BACK]. oil, oil filter and tyres. damage the engine and such damage is not covered by the warranty. To return to the top page of the setting mode, select [BACK]. For checking the engine oil level and adding oil, see “Engine oil” in the “8. Maintenance and [CLOCK]: do-it-yourself” section. Clock adjustment can be set.

Instruments and controls 2-9 WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS

Anti-lock Braking System (ABS) warn- Malfunction warning light (red) (diesel Low temperature indicator light (green) ing light engine model) Brake warning light Seat belt warning light Malfunction Indicator Light (MI or MIL) (orange) Charge warning light Supplemental Restraint System (SRS) Rear fog light indicator light air bag warning light Door open warning light Water-in-fuel-filter warning light (diesel Security indicator light engine model) Electric power steering warning light Electronic Stability Programme (ESP) Slip indicator light* off indicator light* Engine oil pressure warning light Front passenger air bag status light* Trailer direction indicator light

High temperature warning light (red) Front fog lights indicator light* Turn signals/hazard indicator lights

Intelligent Key lock warning light* Glow plug indicator light (diesel engine *: where fitted model) Intelligent Key system warning light* High beam indicator light

CHECKING BULBS and then turn off: , (red), , , Some indicators and warnings are also displayed on , , (green), , , . the vehicle information display. (See “Vehicle infor- With all doors closed, apply the parking brake, fas- mation display” earlier in this section.) ten the seat belts and turn the ignition switch to the If any lights fail to illuminate, it may indicate a burned- ON position without starting the engine. Where fit- out bulb or an open circuit in the electrical system. ted, the following lights will illuminate: , , Have the system checked, and if necessary re- , , . paired, by a NISSAN dealer or qualified workshop promptly. Where fitted, the following lights will illuminate briefly

2-10 Instruments and controls WARNING LIGHTS level could increase the stopping distance and If the brake fluid level is sufficient, have the brake require greater pedal travel distance and ef- system checked by a NISSAN dealer or qualified Anti-lock Braking System (ABS) fort. workshop promptly. warning light Anti-lock Braking System (ABS) warning When the ignition switch is in the ON position, the The brake warning light indicates the parking brake indicator: system operation, a low brake fluid level of the brake Anti-lock Braking System (ABS) warning light illumi- When the parking brake is released and the brake nates and then turns off. This indicates the ABS is system and an Anti-lock Braking System (ABS) malfunction. fluid level is sufficient, if both the brake warning light operational. and the Anti-lock Braking System (ABS) warning Parking brake warning indicator: If the ABS warning light illuminates while the engine light illuminate, it may indicate the ABS is not func- is running, or while driving, it may indicate the ABS When the ignition switch is turned to the ON positioning properly. Have the brake system checked, is not functioning properly. Have the system tion, the brake warning light illuminates. When the and if necessary repaired, by a NISSAN dealer or checked by a NISSAN dealer or qualified workshop engine is started and the parking brake is released, qualified workshop promptly. (See “Anti-lock Brak- promptly. the brake warning light turns off. ing System (ABS) warning light” earlier in this section.) If an ABS malfunction occurs, the anti-lock function If the parking brake is not fully released, the brake is turned off. The brake system then operates nor- warning light remains on. Be sure that the brake Charge warning light mally, but without anti-lock assistance. (See “Brake warning light has turned off before driving. (See system” in the “5. Starting and driving” section.) “Parking brake” in the “3. Pre-driving checks and When the ignition switch is in the ON position, the adjustments” section.) charge warning light illuminates. After starting the Brake warning light Low brake fluid warning indicator: engine, the charge warning light turns off. This indicates the charging system is operational. WARNING If the brake warning light illuminates while the engine is running, or while driving, and the parking If the charge warning light illuminates while the en- • If the brake fluid level is below the minimum brake is released, it may indicate the brake fluid gine is running, or while driving, it may indicate the mark on the brake fluid reservoir, do not drive level is low. charging system is not functioning properly and may the vehicle until the brake system has been need servicing. When the brake warning light illuminates while driv- checked by a NISSAN dealer or qualified When the charge warning light illuminates while driv- workshop. ing, stop the vehicle safely as soon as possible. Stop the engine and check the brake fluid level. If ing, stop the vehicle safely as soon as possible. • Even if you judge it to be safe, have your ve- the brake fluid level is at the minimum mark, add Stop the engine and check the alternator belt. If the hicle towed because driving it could be dan- brake fluid as necessary. (See “Brake fluid” in the alternator belt is loose, broken or missing, the charg- gerous. “8. Maintenance and do-it-yourself” section.) ing system needs repair. (See “Drive belt” in the “8. Maintenance and do-it-yourself” section.) • Depressing the brake pedal without the engine running and/or with a low brake fluid If the alternator belt appears to be functioning cor-

Instruments and controls 2-11 rectly but the charge warning light remains illumi- steering efforts are required to operate the steering High temperature warning light nated, have the charging system checked by a wheel, especially in sharp turns and at low speeds. (red) NISSAN dealer qualified workshop promptly. (See “Electric power steering system” in the When the ignition switch is in the ON position, the CAUTION “5. Starting and driving” section.) high temperature warning light illuminates and then Do not continue driving if the alternator belt is Engine oil pressure warning light turns off. This indicates that the high temperature loose, broken or missing. sensor in the engine coolant system is operational. Door open warning light When the ignition switch is in the ON position, the CAUTION engine oil pressure warning light illuminates. After starting the engine, the engine oil pressure warning If the high temperature warning light illuminates When the ignition switch is in the ON position, the light turns off. This indicates that the oil pressure while the engine is running, it may indicate the door open warning light illuminates if any of the doors sensors in the engine are operational. engine temperature is extremely high. (including the back door) are open or not closed Stop the vehicle safely as soon as possible. securely. If the engine oil pressure warning light illuminates or blinks while the engine is running, it may indicate If the vehicle is overheated, continuing vehicle Electric power steering warning that the engine oil pressure is low. operation may seriously damage the engine. light Stop the vehicle safely as soon as possible. Stop (See “If your vehicle overheats” in the “6. In case When the ignition switch is in the ON position, the the engine immediately and call a NISSAN dealer or of emergency” section for the immediate action electric power steering warning light illuminates. Af- qualified workshop. required.) ter starting the engine, the electric power steering Intelligent Key lock warning light warning light turns off. This indicates the electric CAUTION (where fitted) power steering system is operational. • Running the engine with the engine oil pres- If the electric power steering warning light illumi- sure warning light illuminated could cause se- When the ignition switch is left in the “OFF” position nates while the engine is running, it may indicate the rious damage to the engine. instead of completely turning it to the LOCK position, the Intelligent Key lock warning light blinks in electric power steering system is not functioning The engine oil pressure warning light is not • red and the Intelligent Key room buzzer will sound. properly and may need servicing. Have the electric designed to indicate a low oil level. The oil The light will keep blinking until the ignition switch is power steering system checked by a NISSAN dealer level should be checked using the dipstick. returned to the LOCK or ACC position. or qualified workshop. (See “Engine oil” in the “8. Maintenance and When the electric power steering warning light illu- do-it-yourself” section.) The light will blink for 5 minutes then turn off. minates with the engine running, the power assist to If the Intelligent Key lock warning light blinks and the steering will cease operation but you will still buzzer sounds: have control of the vehicle. At this time, greater • Make sure that the ignition switch is returned to the LOCK position.

2-12 Instruments and controls • Turn the ignition switch to the ACC position. Low fuel warning poor driveability, reduced fuel economy, and damage to the engine control system, which may See “Intelligent Key system (where fitted)” in the affect the vehicle’s warranty coverage. “3. Pre-driving checks and adjustments” section. The fuel gauge indicator in the vehicle information display changes to the low fuel warning. Intelligent Key system warning Seat belt warning light The low fuel warning is displayed when the fuel level Type A: light (where fitted) in the tank is getting low. Refuel as soon as it is con- The Intelligent Key system warning light illuminates venient, preferably before the fuel gauge reaches When the ignition switch is in the ON position, the in green when the ignition switch can be turned. The the empty (0) position. front seat belt warning light on the instrument panel Intelligent Key system warning light illuminates in illuminates. The light will continue to illuminate until There will be a small reserve of fuel remaining in the front seat belt is fastened. (See “Seat belts” in red when the ignition switch cannot be turned even the tank when the fuel gauge reaches the empty though the footbrake pedal is depressed. the “1. Safety — seats, seat belts and supplemental (0) position. restraint system” section.) The Intelligent Key system warning light blinks in red if the Intelligent Key is taken outside of the vehicle Malfunction warning light (red) When the vehicle speed exceeds 15 km/h (10 while the ignition switch is in the ACC or ON posi- (diesel engine model) MPH), the light will blink and the chime will sound unless the front seat belt is securely fastened. The tion. When the ignition switch is turned to the ON posi- chime will continue to sound for about 90 seconds tion, the malfunction warning light illuminates in red. • If the Intelligent Key system warning light blinks, until the seat belt is fastened. make sure of the location of the Intelligent Key as This means that the system is operational. Type B: soon as possible. The Intelligent Key should be For the orange Malfunction Indicator Light (MIL), carried by the driver while operating the vehicle. see “Malfunction Indicator Light (MI or MIL) When the ignition switch is in the ON position, the seat belt warning light illuminates. The light will con- The Intelligent Key system warning light turns off (orange)” later in this section for details. • tinue to illuminate until the driver’s seat belt is fas- about 10 seconds after the Intelligent Key is If the malfunction warning light (red) illuminates con- tened. (See “Seat belts” in the “1. Safety — seats, brought inside the vehicle. tinuously while the engine is running, it may indicate seat belts and supplemental restraint system” sec- The Intelligent Key system warning light blinks in an engine control system malfunction. Have your tion.) green indicating that the Intelligent Key battery is vehicle inspected by a NISSAN dealer or qualified almost discharged. workshop. You do not need to have your vehicle Supplemental Restraint System towed to the dealer. (SRS) air bag warning light (See “Intelligent Key system (where fitted)” in the “3. Pre-driving checks and adjustments” section.) CAUTION When the ignition switch is in the ON or START Continuing vehicle operation without proper ser- position, the Supplemental Restraint System (SRS) vicing of the engine control system could lead to air bag warning light illuminates for about 7 seconds and then turns off. This indicates the SRS air bag system is operational.

Instruments and controls 2-13 If any of the following conditions occur, the SRS air INDICATOR LIGHTS Front fog lights indicator light bag system and pre-tensioner seat belt need servic- (where fitted) ing. Have the system checked, and if necessary Electronic Stability Programme repaired, by a NISSAN dealer or qualified workshop (ESP) off indicator light The front fog lights indicator light illuminates when promptly. (where fitted) the front fog lights are on. (See “Fog light switch” later in this section.) • The SRS air bag warning light remains illumi- The Electronic Stability Programme (ESP) off indi- nated after about 7 seconds. cator light illuminates when the ESP off switch is Glow plug indicator light (diesel pushed to the “OFF” position. engine model) • The SRS air bag warning light flashes intermit- tently. When the ESP off switch is pushed to the “OFF” When the ignition switch is in the ON position, the position, the ESP system is turned off. glow plug indicator light illuminates and turns off The SRS air bag warning light does not come on • after the glow plugs have warmed up. at all. If the ESP off indicator light and slip indicator light illuminate while the engine is running or while driv- If the glow plugs have already warmed up, the glow Unless checked and repaired, the SRS air bag sys- ing, it may indicate the ESP system is not function- plug indicator flashes briefly and then turns off. tem and/or pre-tensioner seat belt may not function ing properly and may need servicing. Have the sys- properly. (See “Supplemental Restraint System tem checked, and if necessary repaired, by a High beam indicator light (SRS)” in the “1. Safety — seats, seat belts and NISSAN dealer or qualified workshop promptly. supplemental restraint system” section.) (See “Electronic Stability Programme (ESP) (where The high beam indicator light illuminates when the Water-in-fuel-filter warning light fitted)” in the “5. Starting and driving” section.) headlight high beam is on. The indicator turns off when the low beam is selected. (See “Headlight (diesel engine model) Front passenger air bag status and turn signal switch” later in this section.) If the water-in-fuel-filter warning light illuminates and/ light (where fitted) or a chime sounds while the engine is running, drain Low temperature indicator light the water from the fuel filter promptly. (See “Fuel fil- The front passenger air bag status light located on (green) the instrument panel will illuminate when the front ter (diesel engine model)” in the “8. Maintenance The low temperature indicator light illuminates when and do-it-yourself” section.) passenger air bag is turned off using the front passenger air bag switch. When the front passenger air the engine coolant temperature is low. CAUTION bag is turned on, the front passenger air bag status When the ignition switch is in the ON position, the Continuing vehicle operation without properly light will turn off. For more details, see “Front pas- low temperature indicator light illuminates and then draining could cause serious damage to the en- senger air bag status light (where fitted)” earlier in turns off after the engine coolant has warmed up. this section. gine. If the low temperature indicator light stays illuminated after the engine has sufficiently warmed up, it may indicate the low temperature sensor in the engine coolant system is not functioning properly and

2-14 Instruments and controls may need servicing. Have the system checked, and Precautions: Security indicator light if necessary repaired, by a NISSAN dealer or quali- To reduce or avoid possible damage to the engine fied workshop promptly. control system when the Malfunction Indicator Light The security indicator light blinks when the ignition Malfunction Indicator Light (MI illuminates or blinks: switch is in the LOCK, “OFF” or ACC position. This function indicates the NATS (NISSAN Anti-Theft or MIL) (orange) • Avoid driving at speeds above 70 km/h (43 System)* equipped on the vehicle is operational. When the ignition switch is in the ON position, the MPH). (* immobilizer) Malfunction Indicator Light illuminates. After starting • Avoid sudden acceleration or deceleration. If NATS is malfunctioning, this light will remain on the engine, the light turns off. This indicates that the while the ignition switch is in the ON position. (See engine control system is operational. • Avoid going up steep uphill grades. “Security system” in the “3. Pre-driving checks and If the Malfunction Indicator Light illuminates or blinks • Avoid carrying or towing unnecessary loads. adjustments” section for additional information.) while the engine is running, it may indicate that the CAUTION engine control system is not functioning properly Slip indicator light (where fitted) Continuing vehicle operation without proper and may need servicing. Have the system checked, • servicing of the engine control system could and if necessary repaired, by a NISSAN dealer or When the ignition switch is in the ON position, the lead to poor driveability, reduced fuel qualified workshop promptly. slip indicator light illuminates and then turns off. This economy, and damage to the engine control indicates the Electronic Stability Programme (ESP) Malfunction indicator on steady: system, which may affect the vehicle’s war- system is operational. ranty coverage. An engine control system malfunction has been de- The slip indicator light blinks when the ESP system tected. Have the vehicle checked, and if necessary • Incorrect setting of the engine control system is operating. repaired, by a NISSAN dealer or qualified workshop may lead to non-compliance of local and na- promptly. You do not need to have your vehicle tional emission laws and regulations. When the indicator light blinks while driving, the towed to the dealer. driving condition is slippery and the vehicle’s trac- Rear fog light indicator light tion limit is about to be exceeded. Malfunction indicator blinking: If the ESP off indicator light and slip indicator light An engine misfire has been detected which may The rear fog light indicator light illuminates when the illuminate while the engine is running or while driv- damage the engine control system. Have the vehicle rear fog light is on. (See “Fog light switch” later in ing, it may indicate the ESP system is not function- checked, and if necessary repaired, by a NISSAN this section.) ing properly and may need servicing. Have the sys- dealer or qualified workshop promptly. tem checked, and if necessary repaired, by a NISSAN dealer or qualified workshop promptly. (See “Electronic Stability Programme (ESP) (where fitted)” in the “5. Starting and driving” section.)

Instruments and controls 2-15 Trailer direction indicator light Intelligent Key buzzer (where fitted) Light reminder chime The Intelligent Key buzzer sounds if any one of the The chime will sound if the driver’s side door is The light will illuminate whenever an additional elec- following improper operations is found. opened while the headlight switch is in either the trical load is detected by the direction indicator sys- or position and the ignition switch is in tem. The ignition switch is not returned to the LOCK • the ACC, “OFF” or LOCK position. position when locking the doors. For additional information, see “Trailer towing” in Be sure to turn the light switch to the “OFF” position the “5. Starting and driving” section. The Intelligent Key is left inside the vehicle when • when you leave the vehicle. locking the doors. Turn signals/hazard indicator Parking brake reminder chime lights • Any doors are not closed securely when locking the doors. The parking brake reminder chime will sound if the The turn signals/hazard indicator lights blink when vehicle is driven at more than 7 km/h (4 MPH) with the turn signal switch or hazard indicator flasher • The mechanical key is inserted into the ignition switch when locking the doors. the parking brake applied. Stop the vehicle and re- switch is turned on. (See “Headlight and turn signal lease the parking brake. switch” later in this section or “Hazard indicator When the buzzer sounds, be sure to check both the flasher switch” later in this section.) vehicle and the Intelligent Key. (See “Intelligent Key AUDIBLE REMINDERS system (where fitted)” in the “3. Pre-driving checks and adjustments” section.) Brake pad wear warning Key reminder chime The disc brake pads have audible wear warnings. Type A: When a brake pad requires replacement, it will make a high pitched scraping sound when the vehicle is in The key reminder chime or buzzer will sound if the motion. This scraping sound will first occur only driver’s door is locked with the power door lock when the brake pedal is depressed. After more wear switch with the door open while the key is left in the of the brake pad, the sound will always be heard ignition switch and the ignition switch is in the ACC, even if the brake pedal is not depressed. Have the “OFF” or LOCK position. brakes checked as soon as possible if the wear Type B: warning sound is heard. The chime or buzzer will sound if the driver’s side Have the system checked, and if necessary re- door is opened while the key is left in the ignition paired, by a NISSAN dealer or qualified workshop switch and the ignition switch is in the ACC, “OFF” promptly. (See “Brakes” in the “8. Maintenance and or LOCK position. do-it-yourself” section.) Be sure to remove the key and carry it with you when you leave the vehicle.

2-16 Instruments and controls HEADLIGHT AND TURN SIGNAL SWITCH

HEADLIGHT SWITCH

SIC3439Z SIC4483Z

SIC4468Z Type C Type A NISSAN recommends that you consult the local CAUTION regulations concerning the use of lights. Do not place any objects on top of the sensor jA. AUTO position (where fitted) The sensor senses the brightness level and controls the autolight function. If the sensor is cov- When the ignition switch is in the ON position and ered, it reacts as if it is dark, and the headlights the headlight switch is in the AUTO position, the will illuminate. headlights, front clearance lights, instrument panel lights, rear combination light and other lights turn on m position automatically depending on the brightness of the surroundings. The position turns on the front clearance, tail, number plate and instrument panel lights. SIC4272Z When the ignition switch is turned to the “OFF” Type B position, the lights will turn off automatically. m position

The position turns on the headlights in addition to the other lights.

Instruments and controls 2-17 HEADLIGHT AIMING CONTROL

SIC3969Z

SIC2275Z Headlight beam To turn on the high beam, push the lever towards Manual type the front position j1. The headlight aiming control operates when the ig- To turn off the high beam, return the lever to the nition switch is in the ON position and the headlight neutral position j2. is on to allow the headlight axis to be adjusted according to the driving condition. To flash the headlights, pull the lever towards the rearmost position j3 . The headlights can be flashed When driving with no heavy load/luggage or driving even when the headlights are not on. on a flat road, select the normal position “0”. Daytime light system (where fitted) If the number of occupants and load/luggage in the vehicle changes, the headlight axis may become Even if the headlight switch is off, the daytime lights higher than normal. will come on after starting the engine. However, you If the vehicle is travelling on a hilly road, the head- cannot change low beam to high beam when the lights may directly shine on the rearview and outside light switch is off. mirrors of a vehicle ahead or the windscreen of an When the light switch is turned to the position, oncoming vehicle, which may obscure other drivers’ the headlight low beam will turn off. vision. To adjust to the proper aiming height, turn the switch accordingly. The higher the number, designated on the switch, the lower the headlight axis.

2-18 Instruments and controls Select the switch position by referring to the following samples.

Model without rear seats (Van):

Switch Number of front seat Number of rear seat Weight of load in the luggage compart- position occupants occupants ment 0 No load Driver only 0 Approximately 634 kg (1,398 lb) 2 When towing a trailer

Model with second row seats (Wagon):

Switch Number of front seat Number of second Weight of load in the luggage position occupants row seat occupants compartment Driver only 0 0 No load 12 3 2 Approximately 259 kg (571 lb) Driver only 0 Approximately 475 kg (1,047 lb) 3 When towing a trailer

Instruments and controls 2-19 Model with third row seats (Wagon): BATTERY SAVER SYSTEM

Switch Number of front seat Number of second Number of third row Weight of load in the luggage The light reminder chime will sound if the headlight position occupants row seat occupants seat occupants compartment switch is in either the or position and Driver only when the driver’s door is opened with the ignition 0 0 switch in the ACC, “OFF” or LOCK position. 0 No load Type A 1 2 2 3 If the ignition switch is turned to “OFF” or LOCK 2 Approximately 66 kg (146 lb) position while the headlight switch is in the or Approximately 392 kg (864 position, the battery saver function will turn off Driver only 0 0 3 lb) the lights after 5 minutes to prevent the battery from When towing a trailer being discharged. The lights will turn on when the doors are being opened. Type B If the doors are closed and locked with the integrated keyfob while the headlight switch is in either the or position, the battery saver function will turn off the lights to prevent the battery from being discharged. The lights will turn on when the doors are being opened. CAUTION Do not leave the lights on when the engine is not running for extended periods of time to prevent the battery from being discharged.

2-20 Instruments and controls FOG LIGHT SWITCH

TURN SIGNAL SWITCH FRONT FOG LIGHTS (where fitted) position will turn on the headlights, fog lights and the other lights while the ignition switch is in the ON position or the engine is running. REAR FOG LIGHT The rear fog light should be used only when visibility is seriously reduced [generally, to less than 100 m (328 ft)]. Type A To turn the rear fog light on, turn the headlight switch SIC3970Z SIC3971AZ to the or position, then turn the switch to Type A the position j2 . The switch returns to the CAUTION position automatically, and the rear fog light will illuminate with the front fog lights. Make sure the The turn signal switch will not be cancelled auto- indicator light on the instrument panel illumi- matically if the steering wheel turning angle does nates. not exceed the preset amount. After the turn or lane change, make sure that the turn signal To turn the rear fog light off, turn the fog light switch switch is returned to its original position. to the position again. Make sure the indicator on the instrument panel turns off. Turn signal j To turn both the front and rear fog lights off, turn the To turn on the turn signals, move the lever up 1or fog light switch to the “OFF” position. down j2 to the point where the lever latches. When SIC3217Z When the headlight switch is in the AUTO position: the turn is completed, the turn signal cancels auto- Type B matically. To turn on the front fog lights, turn the headlight Turning the fog light switch to the or Lane change signal switch to the or position, then turn the position will turn on the headlights, fog lights and fog light switch to the position j1. the other lights while the ignition switch is in the ON To turn on the lane change signals, move the lever position or the engine is running. up j1 or down j2 to the point where the light be- To turn the fog lights off, turn the switch to the gins to flash. “OFF” position. Type B To cancel the flashing, move the lever to the oppo- When the headlight switch is in the AUTO position: To turn the rear fog light on, turn the headlight switch site direction. to the or position, then turn the switch to Turning the fog light switch to the or the position j2 . The switch returns to the

Instruments and controls 2-21 WIPER AND WASHER SWITCH

“OFF” position automatically, and the rear fog light Wiper operation will illuminate with the front fog lights. Make sure the WARNING The lever position INT j1 operates the wiper inter- indicator light on the instrument panel illumi- In freezing temperatures, the washer fluid may mittently. The intermittent operation can be adjusted nates. freeze on the windscreen and obscure your vi- by turning the adjustment control knob, (longer) jA sion. Warm the windscreen with the defogger be- To turn the rear fog light off, turn the fog light switch or (shorter) jB. to the position again. Make sure the indi- fore you wash the windscreen. The speed of the intermittent operation varies de- cator on the instrument panel turns off. CAUTION pending on the vehicle speed. To turn both the front and rear fog lights off, turn the Do not operate the washer continuously for • The lever position LO j2 operates the wiper at low fog light switch to the “OFF” position. longer than 30 seconds. speed. When the headlight switch is in the AUTO position: Do not operate the washer if the window • The lever position HI j3 operates the wiper at high washer reservoir is empty. Turning the fog light switch to the or speed. position will turn on the headlights, fog lights and WINDSCREEN WIPER AND WASHER To stop the wiper operation, move the lever up to the other lights while the ignition switch is in the ON SWITCH j position or the engine is running. the OFF position C. The lever position MIST j4 operates the wiper one sweep. The lever automatically returns to its original position. If the windscreen wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice on and around the wiper arms. In approximately 20 seconds, turn the switch on again to SIC3218Z operate the wiper.

The windscreen wiper and washer operate when Washer operation the ignition switch is in the ON position. To operate the washer, pull the lever toward the rear of the vehicle j5 until the desired amount of washer fluid is spread on the windscreen. The wiper will automatically operate several times.

2-22 Instruments and controls Wiper drip wipe system: • Low — Low sensitive operation REAR WINDOW WIPER AND The wiper will also operate once about 3 seconds To turn the rain-sensing auto wiper system off, push WASHER SWITCH (where fitted) after the washer and wiper are operated. This op- up the lever to the OFF position, or pull down the eration is to wipe washer fluid that has dripped on lever to the “ ” (LO) or “ ” (HI) position. the windscreen. CAUTION RAIN-SENSING AUTO WIPER Do not touch the rain sensor and around it when SYSTEM (where fitted) the wiper switch is in the AUTO position and the ignition switch is in the ON position. The wipers may operate unexpectedly and cause to an injury or a wiper damage.

• The rain-sensing auto wipers are intended for SIC3565Z use during rain. If the switch is left in the AUTO position, the wipers may operate unexpectedly when dirt, fingerprints, oil film or insects The rear window wiper and washer operates when are stuck on or around the sensor. The wipers the ignition switch is in the ON position. may also operate when exhaust gas or mois- Wiper operation SIC4469Z ture affect the rain sensor. The switch position j1 operates the wiper intermit- • When the windscreen glass is coated with wa- tently. The rain-sensing auto wiper system can automati- ter repellent, the speed of the rain-sensing j cally turn on the wipers and adjust the wiper speed auto wipers may be higher even though the The switch position 2 operates the wiper at low depending on the rainfall and the vehicle speed by amount of the rainfall is small. speed. using the rain sensor located on the upper part of Be sure to turn off the rain-sensing auto wiper If the rear window wiper operation is interrupted the windscreen. • system when you use a car wash. by snow or ice, the wiper may stop moving to To set the rain-sensing auto wiper system, push the protect its motor. If this occurs, turn the wiper The rain-sensing auto wipers may not operate lever down to the AUTO position j1 . The wiper will • switch to the OFF position and remove the snow if rain does not hit the rain sensor even if it is sweep once while the ignition switch is in the ON or ice on and around the wiper arms. In approxi- raining. position. mately 1 minute, turn the switch on again to operate the wiper. The rain sensor sensitivity level can be adjusted by turning the knob toward the front j2 (High) or toward the rear j3 (Low). • High — High sensitive operation

Instruments and controls 2-23 DEFOGGER SWITCH HAZARD INDICATOR FLASHER (where fitted) SWITCH

Reverse synchronisation function: When the windscreen wiper switch is on, moving the shift lever to the R (Reverse) position will operate the rear window wiper and washer. The rear window wiper will be operated once every 7 seconds while the above conditions are kept. Washer operation To operate the washer, push the lever toward the front of the vehicle j3 until the desired amount of SIC1986AZ SIC2475Z washer fluid is spread on the windscreen. The wiper will automatically operate several times. The defogger switch operates when the ignition The hazard indicator flasher switch operates regard- Wiper drip wipe system: switch is in the ON position. less of the ignition switch position except when the battery is discharged. The wiper will also operate once about 3 seconds The defogger is used to reduce the moisture, fog or after the washer and wiper are operated. This op- frost on the rear window and outside door mirror The hazard indicator flasher is used to warn other eration is to wipe washer fluid that has dripped on surface (where fitted with the defogger) to improve drivers when you have to stop or park under emer- the rear window. the rear view. gency conditions. When the defogger switch is pushed, the indicator When the hazard indicator flasher switch is pushed, light jA illuminates and the defogger operates for all turn signal lights will flash. To turn off the hazard approximately 15 minutes. After the preset time has indicator flasher, push the hazard indicator flasher passed, the defogger will turn off automatically. switch again. To turn off manually, push the defogger switch again. CAUTION • When operating the defogger continuously, be sure to start the engine. Otherwise, it may cause the battery to discharge. • When cleaning the inner side of the window, be careful not to scratch or damage the electrical conductors on the surface of the window.

2-24 Instruments and controls HORN WINDOWS

MANUAL WINDOWS (where fitted) the vehicle. They could unknowingly activate switches or controls and inadvertently The windows can be opened or closed by turning become involved in an accident. the hand crank on each door. The power windows operate when the ignition SLIDING WINDOWS (where fitted) switch is in the ON position. To open a window, push down the power window switch. To close a window, pull up the power window

SIC4220Z switch.

The horn switch operates regardless of the ignition switch position except when the battery is discharged. SIC4202Z When the horn switch is pushed and held, the horn will sound. Releasing the horn switch will cease the j horn sound. To open the sliding window, squeeze the knob 1 and slide the window open j2 toward the front of the vehicle. SIC4200Z To close, completely close the window until there is a locking sound. POWER WINDOWS (where fitted)

WARNING • Make sure that all passengers have their hands, etc. inside the vehicle before operating the power windows. • Never leave children or adults who would normally require the support of others alone in

Instruments and controls 2-25 Driver’s window switch Automatic function the auto-reverse function may activate if an impact or load similar to something being caught in the win- The driver’s switch, the main, switch can control the The automatic function is available for the switch dow occurs. front windows. that has an mark on its surface. When power window switch does not The automatic function enables a window to fully open or close without holding the switch down or operate up. Some power window functions (automatic close To fully open the window, push the power window function, auto-reverse function and window timer) switch down to the second detent and release the will not operate as described after the battery cable switch. To fully close the window, pull the power is disconnected and the electrical supply is inter- window switch up to the second detent and release rupted. Perform the following procedure to initialise the switch. The switch does not have to be held dur- the power window functions. ing window operation. 1. Turn the ignition switch to the ON position. SIC3854Z To stop the window open/close operation during 2. If the driver’s window is closed, open it com- the automatic function, push down or pull up the pletely by operating the driver’s window switch. Passenger’s window switch switch in opposite directions. 3. Pull up and hold the driver’s window switch to The passenger’s switch can control its correspond- Auto-reverse function: close the driver’s window. Hold the switch for ing window. approximately 3 seconds after the window has WARNING been fully closed, and then release it. There is a small distance just before the closed 4. Check if the power window functions operate position which cannot be detected. Make sure properly. that all passengers have their hands, etc. inside the vehicle before closing the windows. If you open or close the power window continuously, it may cause the power window not to oper- The auto-reverse function enables a window to au- ate properly. Perform the above procedure. tomatically reverse when something is caught in the If the power window functions do not operate prop- window as it is closing by the automatic function. erly after performing the above procedure, repeat When the control unit detects an obstacle, the win- SIC4201Z the steps. See a NISSAN dealer or qualified work- dow will be lowered immediately. shop, if necessary, for checking the power window Depending on the environment or driving conditions, system.

2-26 Instruments and controls CLOCK POWER OUTLET

Meter display: The digital clock displays the time 2. Push the MENU button j2 and turn the VOL/ when the CLOCK mode is selected in the trip com- MENU dial j3 until “CLOCK” is displayed. puter. (See “Trip computer” in the “2. Instruments 3. Push the ENTER button j4 . (“CLOCK OFF” is and controls” section for the clock setting.) displayed.) Audio display (where fitted): The digital clock (in the 4. Turn the VOL/MENU dial j3 to turn the clock audio unit) displays the time when the ignition switch display mode on. (“CLOCK ON” is displayed.) is in the ACC or ON position and the CLOCK ON mode is selected. 5. Push the ENTER button j4 . The hour display will start flashing. If the battery cable is disconnected, the clock will reset its time and the display mode. 6. Turn the VOL/MENU dial j3 to adjust the time. SIC4203Z Front ADJUSTING TIME 7. Push the ENTER button j4 . The minute display will start flashing. 8. Turn the VOL/MENU dial j3 to adjust the time. 9. Push the ENTER button j4 to finish the clock adjustment. When clock is displayed: 1. Turn the audio unit on by pushing the POWER ON/OFF button j1.

2. Push the MENU button j2 and turn the VOL/ SIC4482Z SIC4245Z MENU dial j3 until “CLOCK” is displayed. Second row seat (where fitted) 3. Push the ENTER button j4 . (“CLOCK ON” is The power outlet is for powering electrical accesso- Audio display model (where fitted) displayed.) ries. You can select clock display ON and OFF mode. 4. Perform steps 5 to 9 above to adjust the time. CAUTION When clock is not displayed: • The outlet and plug may be hot during or im- If the clock is not displayed with the ignition switch mediately after use. in the ACC or ON position, you need to select the This power outlet is not designed for use with CLOCK ON mode as follows: • a cigarette lighter unit. 1. Turn the audio unit on by pushing the POWER ON/OFF button j1.

Instruments and controls 2-27 ASHTRAY STORAGE

• Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use WARNING double adapters or more than one electrical • The storage compartments should not be accessory. used while driving so that full attention may • Use power outlet with the engine running to be given to vehicle operation. avoid discharging the vehicle battery. • Keep the storage lids closed while driving to • Avoid using power outlet when the air condi- help prevent injury in an accident or sudden tioner, headlights or rear window defogger is stop. on. SIC4204Z GLOVE BOX • Before inserting or disconnecting a plug, be sure to turn off the power switch of the elec- j trical accessory being used and the ignition To open the ashtray, pull the lid 1. switch. To take out the ashtray, push j2 and pull the ash- • Push the plug in as far as it will go. If good tray out. contact is not made, the plug may overheat or the internal temperature fuse may blow. • Do not allow water to contact the outlet. • When not in use, be sure to close the cap. SIC4205Z

Tray (where fitted) To open the tray, pull the handle. To close, push the tray until it locks.

2-28 Instruments and controls CONSOLE BOX To close, push in until it stops and pull the tray up CUP HOLDERS until it locks. CAUTION Do not overfill the tray with materials. They can touch or strike the seat adjustment lever and may hinder the operation of the lever, or materials may get stuck inside the tray. BOTTLE HOLDERS (where fitted)

SIC4206Z SIC4208Z Front To open the console box lid, push the knob jAup and pull the lid up. To close, push the lid down until it locks. UNDER-SEAT TRAY (where fitted)

SIC4467Z

The holders are located in the sliding door pockets. CAUTION SIC4209Z Rear Do not put an open bottle in the holder, as the drink may spill when opening or closing the door Front and Second row seat or while driving.

SIC4207Z WARNING The driver must not remove or insert cups into To open the under-seat tray, pull the tray up and for- the cup holder while driving so that full attention ward toward the front of the vehicle. may be given to vehicle operation.

Instruments and controls 2-29 CAUTION PERSONAL TABLE (where fitted) HOOKS Avoid abrupt starting and braking especially when the cup holder is being used to prevent spilling the contents. If the contents are hot, they could scald you or your passengers.

SIC4466Z SIC4497Z

The personal table is located on the rear side of the WARNING front seatbacks. To use the table, pull the table up SIC4487Z as illustrated jA until it locks. Do not apply a total load of more than 3 kg (7 lb) Third row seat (where fitted) to a single hook. When storing the table, hold the centre edge of the Third row seat (where fitted) table and push the table down jB. The third row seat cup holder is located on the side CAUTION of the third row seat. To use the cup holder, pull it Do not use the table while driving. down jA until it locks. • When the table is not in use, store it to pre- jB. • When storing the cup holder, push it up vent an injury or accident. CAUTION • Do not apply or place a total load of more than • Store the cup holders when entering or leav- 3 kg (7 lb) on the table. This may damage the ing the third row seat. table. • Do not apply an excessive force to the cup holders.

2-30 Instruments and controls CARD HOLDER TICKET HOLDERS UTILITY HOOK

SIC4211Z SIC4271Z SIC4210Z

A single card (credit-card sized) can be inserted. To access the ticket holders, pull the sun visor down. CAUTION CAUTION CAUTION Do not apply a total load of more than 3 kg (6 lb) to the hook. Do not insert a card smaller or thinner than the Do not insert a card thicker than 1 mm (0.04 in) opening. It will become stuck inside and will not or several tickets to the holders. be able to be pulled out.

Instruments and controls 2-31 LUGGAGE HOOKS Type A: There are4-6hooksonthefloor,depending on the model. Type B: 4 hooks are available (stored in the glove box). At- tach the hooks to the rail on the luggage compartment. Push and hold the centre of the hook j1 as shown to attach/remove or move it right or left j2. SIC4224Z SIC4222Z TONNEAU COVER (where fitted) Type A To use the tonneau cover, pull it out toward the front j1 and rear j2 of the vehicle, hang both sides on WARNING the hooks j3. Never put anything on the tonneau cover, no • To remove the tonneau cover, remove it from the matter how small. Any object on it could cause hooks and hold until it is retracted. an injury in an accident or sudden stop. To stow the tonneau cover, stow the cover and tap Do not leave the tonneau cover in the vehicle • the holder to the upper side. with it disengaged from the holder. The tonneau cover keeps the luggage compartment contents hidden from the outside. SIC4223Z Type B

WARNING • Always make sure that the luggage is properly secured. Use the suitable ropes and hooks. • Unsecured luggage can become dangerous in an accident or sudden stop.

2-32 Instruments and controls SUN VISORS

PARTITION (where fitted) Mesh-type The partition can be folded and a long object can be loaded. CAUTION Be sure to latch the partition in position after opening or closing it. 1. Fold the front passenger’s seat by pulling the reclining lever jA. 2. Pull up the lever jB located on the front passenger’s seat side to release the partition support. 3. Fold the partition toward the front of the vehicle. 4. Pull down the lever and fit the partition support into the hole jC on the front passenger’s seatback.

SIC2872

1. To block out glare from the front, swing down the sun visor j1. 2. To block glare from the side, remove the sun visor from the centre mount and swing it to the side j2.

SIC4221

Instruments and controls 2-33 INTERIOR LIGHTS

CAUTION • The ignition switch is turned to the LOCK posi- LUGGAGE COMPARTMENT LIGHT tion. (Intelligent Key system equipped model) • Do not leave the light switch on when the engine is not running for extended periods of • The driver’s door is unlocked without the key in time to prevent the battery from being dis- the ignition switch. charged. • The driver’s door is opened and then closed • Turn off the lights when you leave the vehicle. without the key in the ignition switch. ROOM LIGHT *1: Model with the Intelligent Key system or remote keyless entry system *2: Model without the Intelligent Key system or remote keyless entry system SIC3110AZ The interior light timer will be cancelled when: When the switch is in the ON position j1 , the light The driver’s door is locked. • illuminates while the back door is opened. The ignition switch is turned to the ON position. • The interior light timer will keep the luggage com- When the switch is in the “OFF” position j3 , the partment light illuminated for approximately 30 seconds (*1) or 8 seconds (*2) when: SIC2489Z room light does not illuminate, regardless of any condition. • The key is removed from the ignition switch with the driver’s door closed. The room light has a three-position switch. Battery saver system The ignition switch is turned to the LOCK posi- When the switch is in the ON position j2 , the room If any door is left open for more than 15 minutes with • · j light illuminates. the room light switch in the “ ” (Door) position 1, tion (Intelligent Key system equipped model). the room light will automatically turn off. Whentheswitchisinthe“·” (Door) position j1, • The driver’s door is unlocked without the key in the room light illuminates when a door is opened. the ignition switch. The interior light timer will keep the room light on for • The driver’s door is opened and then closed approximately 30 seconds (*1) or 8 seconds (*2) without the key in the ignition switch. when: *1: Model with the Intelligent Key system or remote keyless entry system • The key is removed from the ignition switch with the driver’s door closed. *2: Model without the Intelligent Key system or remote keyless entry system

2-34 Instruments and controls The interior light timer will be cancelled when: • The driver’s door is locked. • The ignition switch is turned to the ON position. When the switch is in the “OFF” position j2 , the light does not illuminate, regardless of the condition. Battery saver system If any door is left open for more than 15 minutes with the luggage compartment light switch in the ON position j1 , the luggage compartment light will automatically turn off.

Instruments and controls 2-35 NOTE

2-36 Instruments and controls 3 Pre-driving checks and adjustments

Keys ...... 3-2 Opening bonnet...... 3-19 NISSAN Anti-Theft System (NATS*) key ...... 3-2 Closing bonnet ...... 3-19 Intelligent Key (where fitted)...... 3-3 Back door...... 3-20 Door locks...... 3-4 Locking or unlocking back door ...... 3-20 Super Lock System (where fitted)...... 3-4 Tailgate ...... 3-20 Front door ...... 3-5 French doors...... 3-21 Sliding door...... 3-6 Fuel filler lid ...... 3-22 Remote keyless entry system (where fitted)...... 3-8 Opening fuel filler lid...... 3-22 Using remote keyless entry system ...... 3-8 Fuel filler cap...... 3-22 Intelligent Key system (where fitted) ...... 3-10 Steering wheel...... 3-23 Operating range ...... 3-11 Tilt operation...... 3-23 Using Intelligent Key system...... 3-12 Mirrors...... 3-23 Using remote keyless entry function ...... 3-13 Inside rearview mirror (where fitted) ...... 3-23 Warning lights and audible reminders ...... 3-15 Outside rearview mirrors...... 3-23 Security system ...... 3-18 Parking brake ...... 3-24 NISSAN Anti-Theft System (NATS)...... 3-18 Lever type ...... 3-24 Bonnet...... 3-19 KEYS

Your vehicle can only be driven with the keys spe- NISSAN ANTI-THEFT SYSTEM cific to your vehicle. A key number plate is supplied (NATS*) KEY with your key. Record the key number and keep the key number plate in a safe place, except in the vehicle, in case of the need to duplicate the keys. The key can only be duplicated using an original key or the original key number. The key number is required when you have lost all of the keys and do not have the original key to duplicate from. If the key is lost, or you need extra keys, provide an original key SPA2670Z or the key number to a NISSAN dealer or qualified Type C workshop. SPA1981Z 1 NATS key or integrated keyfob (with NATS) CAUTION Type A 2 Key number plate Do not leave the keys inside the vehicle when leaving the vehicle. 3 NATS key Your vehicle can only be driven with the NATS key or the integrated keyfob (where fitted), which are registered to your vehicle’s NATS components. As many as 4 NATS keys or integrated keyfobs can be registered and used with one vehicle. The new keys must be registered by a NISSAN dealer or qualified workshop prior to use with the NATS of your vehicle. Since the registration process requires eras- SPA1982Z ing all memory in the NATS components when reg- Type B istering new keys, be sure to take all NATS keys or integrated keyfobs that you have to the NISSAN dealer or qualified workshop. CAUTION Do not allow the NATS key or the integrated keyfob, which contain an electrical transponder, to come into contact with water or salt water. This could affect the system function.

3-2 Pre-driving checks and adjustments *: Immobilizer Your vehicle can only be driven with the Intelligent *: Immobilizer Keys, which are registered to your vehicle’s Intelli- INTELLIGENT KEY (where fitted) gent Key system components and NISSAN Anti- Theft System (NATS*) components. As many as 4 Intelligent Keys can be registered and used with one vehicle. The new keys must be registered by a NISSAN dealer or qualified workshop prior to use with the Intelligent Key system and NATS of your vehicle. Since the registration process requires erasing all memory in the Intelligent Key components when registering new keys, be sure to take all Intelligent Keys that you have to the NISSAN dealer or qualified workshop. CAUTION • Do not allow the Intelligent Key, which contains electrical components, to come into contact with water or salt water. This could affect the system function. • Do not drop the Intelligent Key. • Do not strike the Intelligent Key sharply against another object. • Do not place the Intelligent Key for an extended period in an area where temperatures

SPA2661 exceed 60°C (140°F). • Do not attach the Intelligent Key with a key 1. Intelligent Key (2) holder that contains a magnet. 2. Mechanical key (in the Intelligent Key) (2) • Do not place the Intelligent Key near equipment that produces a magnetic field, such as 3. Key number plate a TV, audio equipment and personal comput- 4. Ignition switch cap ers.

Pre-driving checks and adjustments 3-3 DOOR LOCKS

Key, release the lock knob j1 onthesideofthe Intelligent Key. Then remove and unfold the me- WARNING chanical key j2. • Always look before opening any doors, to To install the mechanical key, fold the key and firmly avoid an accident with oncoming traffic. insert it into the Intelligent Key until the lock knob • Never leave children or adults who would nor- returns to the lock position. mally require the support of others alone in CAUTION the vehicle. They could unknowingly activate switches or controls and inadvertently Always carry the mechanical key installed in the become involved in a serious accident. Intelligent Key slot. SUPER LOCK SYSTEM (where fitted)

WARNING For the Super Lock System equipped model, failure to follow the precautions below may lead to hazardous situations. Make sure the Super Lock System activation is always safely conducted. • When the vehicle is occupied, never lock the doors with the integrated keyfob or the Intel- SPA2393Z ligent Key (where fitted). Doing so will trap the occupants, since the Super Lock System Ignition switch cap prevents the doors from being opened from SPA2376 the inside of the vehicle. Attach the ignition switch cap jA to the ignition Only operate the integrated keyfob or the In- switch as illustrated. • Mechanical key telligent Key (where fitted) lock button when Remove the ignition switch cap jA when the me- there is a clear view of the vehicle. This is to Two copies of the mechanical key, which can be chanical key is used. prevent anybody from being trapped inside used in case of a discharged battery, are supplied the vehicle through the Supper Lock System with your vehicle. activation. The mechanical key can be used for operation in the same way as an ordinary key (NATS key). Locking the doors with the integrated keyfob or the To remove the mechanical key from the Intelligent

3-4 Pre-driving checks and adjustments Intelligent Key* (where fitted) will lock all doors in- FRONT DOOR cluding the back door and activate the Super Lock System. This means that none of the doors can be opened from the inside in order to prevent theft. The system will be released when the door is unlocked with the integrated keyfob or Intelligent Key* (where fitted).

The Super Lock System will not activate when the SPA2169Z doors are locked with the power door lock switch or SPA2662Z Type A the key. Locking with inside lock knob *: “LOCK” button or door handle/back door request switch Locking with key CAUTION Type A: Emergency situations When locking the doors using the inside lock To lock the door, insert the key to the door key cyl- knob, be sure not to leave the key in the vehicle. If the Super Lock System is activated due to a traf- inder (driver’s or front passenger’s) and turn the key Type A: fic accident or other unexpected circumstances to the front side of the vehicle j1 . The correspond- while you are in the vehicle: ing door will lock. To lock the door, push the inside lock knob to the lock position j1 , and then close the door. • Turn the ignition switch to the ON position, the To unlock the door, turn the key to the rear of the Super Lock System will be released and all the vehicle j2 . The corresponding door will unlock. To unlock the door, push the inside lock knob to the doors can be unlocked with the power door lock unlock position j2. switch. You can then open the doors. Type B: Remove the key from the ignition switch and un- To lock the door, insert the key to the driver’s door • key cylinder and turn the key to the front side of the lock the door using the integrated keyfob or the j Intelligent Key (where fitted). The Super Lock vehicle 1 . All the doors including the back door will System will be released and you can open the lock. door. To unlock the door, turn the key to the rear side of the vehicle j2 . All the doors including the back door will unlock.

Pre-driving checks and adjustments 3-5 Locking with power door lock switch Lockout protection: (where fitted) The power door lock switch will not lock the doors CAUTION under the following conditions: Type A: When locking the doors using the power door lock switch, be sure not to leave the key in the • When the key is in the ignition switch and the vehicle. driver’s door is open. The power door lock switch is located in the centre • When any door except for the driver’s door is of the instrument panel. open. SPA2671Z Model without Super Lock System: Type B: Type B To lock the doors, push the power door lock switch Type B: • When the key is in the ignition switch and the to the lock position j1 with the driver’s door open driver’s door is open. To unlock and open the door, pull the inside door and the key removed from the ignition switch, then handle as illustrated. close the door. All doors including the back door Type C: will lock. The doors cannot be opened by using the inside • When the key is in the ignition switch and any door handle when the Super Lock System (where To unlock, push the power door lock switch to the door is open. fitted) is activated. unlock position j2. SLIDING DOOR Model with Super Lock System: To lock the doors, push the power door lock switch to the lock position j1 with the driver’s door open and the key removed from the ignition switch, then close the door. All doors including the back door will lock. To unlock, push the power door lock switch to the unlock position j2.

SPA1848Z When the Super Lock System is activated, it is not SPA2693Z possible to operate the power door lock switch. With key cylinder

3-6 Pre-driving checks and adjustments Model with key cylinder Insert the key to the sliding door key cylinder and turn the key toward the front of the vehicle j1to lock the sliding door. Turn the key toward the rear of the vehicle j2to unlock the sliding door. Model with integrated keyfob or Intelligent Key SPA2663Z SPA2694Z The sliding door can be locked or unlocked with one of the following operations. Opening or closing sliding door Locking with inside lock knob • Push the “LOCK” or “UNLOCK” button on the integrated keyfob or the Intelligent Operate the sliding door by pulling the door handle. To lock or unlock the sliding door, move the inside lock knob to the LOCK j1 or UNLOCK j2 posi- Key (where fitted). (See “Remote keyless entry CAUTION system (where fitted)” later in this section or “In- tion. telligent Key system (where fitted)” later in this Always use the door handle to open or close • To lock from the outside without a key, move the section.) In selective unlock mode, push the the sliding door. Do not attempt to open or lock knob to the LOCK position j1 , then close the “UNLOCK” button twice to unlock the sliding close the door by merely placing your hand on door. door. the door edge or door slide roller as this may cause injury. • Push any of the request switches (where fitted). (See “Intelligent Key system (where fitted)” later • When opening the door on a slope, ensure in this section.) In selective unlock mode, the that it is fully open and that it does not close driver’s door handle or back door request switch by itself. needs to be pushed twice to unlock the sliding door. • Push the power door lock switch to the lock or unlock position. • Lock or unlock the driver’s door lock with the SPA2695Z key or the inside door lock knob.

Pre-driving checks and adjustments 3-7 REMOTE KEYLESS ENTRY SYSTEM (where fitted)

Child safety sliding door lock The remote keyless entry system can operate all • Do not place the integrated keyfob for an ex- (where fitted) door locks (including the back door) using the inte- tended period in an area where temperatures grated keyfob. The integrated keyfob can operate at exceed 60°C (140°F). The child safety sliding door lock helps prevent slid- a distance of approximately 1 m (3.3 ft) away from If a integrated keyfob is lost or stolen, NISSAN rec- ing doors from being opened accidentally, espe- the vehicle. The operating distance depends upon ommends erasing the ID code of that integrated cially when small children are in the vehicle. the conditions around the vehicle. keyfob from the vehicle. This may prevent the unau- When the lever is in the lock position j1 , the child As many as 4 integrated keyfobs can be used with thorised use of the integrated keyfob to unlock the safety sliding door lock engages and the sliding door one vehicle. For information about the purchase and vehicle. For information regarding the erasing pro- can only be opened by the outside door handle. use of additional integrated keyfobs, contact a cedure, contact a NISSAN dealer or qualified work- To disengage, move the lever to the unlock position NISSAN dealer or qualified workshop. shop. j2. The integrated keyfob will not function under the fol- For information regarding the replacement of a bat- lowing conditions: tery, see “Battery” in the “8. Maintenance and do-it-yourself” section. • When the distance between the integrated keyfob and vehicle is more than approximately 1 m USING REMOTE KEYLESS ENTRY (3.3 ft). SYSTEM • When the integrated keyfob battery is discharged. • When the key is in the ignition switch. CAUTION • When locking the doors using the integrated keyfob, be sure not to leave the key in the vehicle. • Do not allow the integrated keyfob, which contains electrical components, to come into SPA2021Z contact with water or salt water. This could affect the system function. j1 “LOCK” button • Do not drop the integrated keyfob. j2 “UNLOCK” button • Do not strike the integrated keyfob sharply against another object.

3-8 Pre-driving checks and adjustments Unlocking doors mode, which unlocks the passenger’s doors at the WARNING second push of the “UNLOCK” button j2. All door unlock mode: For Super Lock System equipped models, failure To switch to the selective door unlock mode, push 1. Push the “UNLOCK” button on the inte- to follow the precautions below may lead to haz- the “LOCK” and “UNLOCK” buttons grated keyfob. ardous situations. Make sure the Super Lock Sys- simultaneously for more than 5 seconds. tem activation is always safely conducted. 2. All doors (including the back door) will be un- Perform the same procedure to deactivate the se- locked. • When the vehicle is occupied, never lock the lective door unlock mode. doors with the integrated keyfob. Doing so All doors will be locked automatically unless one of When the selective unlock mode is set, the haz- will trap the occupants, since the Super Lock the following operations is performed within 2 min- • ard indicator flashes once. System prevents the doors from being opened utes after pushing the “UNLOCK” button. from the inside of the vehicle. When the all door unlock mode is set, the hazard • Opening any door. • • Only operate the integrated keyfob lock but- indicator flashes 3 times. ton when there is a clear view of the vehicle. • Inserting the key into the ignition switch. This is to prevent anybody from being trapped During this 2-minute time period, if the “UNLOCK” inside the vehicle through the Supper Lock button is pushed, all doors will be locked auto- System activation. matically after another 2 minutes. Locking doors Selective door unlock mode: 1. Remove the key from the ignition switch. 1. Push the “UNLOCK” button j2 on the integrated keyfob. 2. Close all doors (including the back door). 2. The driver’s door will unlock. 3. Push the “LOCK” button j1 on the integrated keyfob. 3. Push the “UNLOCK” button j2 on the integrated keyfob again. 4. All doors will be locked. 4. All doors (including the back door) will be un- 5. Operate door handles to confirm that the doors locked. have been securely locked. Selecting door unlock mode: CAUTION When you first receive the vehicle, the door unlock After locking the doors using the integrated key- mode is set to unlock all the doors with one push of fob, be sure that the doors have been securely the “UNLOCK” button j2 . The door unlock locked by operating the door handles. mode can be switched to the selective door unlock

Pre-driving checks and adjustments 3-9 INTELLIGENT KEY SYSTEM (where fitted)

• When in possession of wireless equipment, such WARNING as a mobile telephone, transceiver, and CB ra- Radio waves could adversely affect electric medi- dio. cal equipment. Those who use a pacemaker • When the Intelligent Key is in contact with or should contact the electric medical equipment covered by metallic materials. manufacturer for the possible influences before use. • When any type of radio wave remote control is used nearby. The Intelligent Key system can operate all the door locks (including the back door lock) using the inte- • When the Intelligent Key is placed near an elec- grated keyfob function or pushing the request switch tric appliance such as a personal computer. on the vehicle without taking the key out from a In such cases, correct the operating conditions be- pocket or purse. The operating environment and/or fore using the Intelligent Key function or use the conditions may affect the Intelligent Key system op- mechanical key. eration. Although the life of the battery varies depending on Be sure to read the following before using the Intel- the operating conditions, the battery’s life is approxi- ligent Key system. mately 2 years. If the battery is discharged, replace CAUTION it with a new one. • Be sure to carry the Intelligent Key with you Since the Intelligent Key is continuously receiving when operating the vehicle. radio waves, if the key is left near equipment which transmits strong radio waves, such as signals from • Never leave the Intelligent Key in the vehicle a TV and personal computer, the battery life may when you leave the vehicle. SPA2661 become shorter. The Intelligent Key is always communicating with For information regarding replacement of a battery, the vehicle as it receives radio waves. The Intelligent 1. Intelligent Key (2) see “Battery” in the “8. Maintenance and Key system transmits weak radio waves. Environ- do-it-yourself” section. 2. Mechanical key (in the Intelligent Key) (2) mental conditions may interfere with the operation of the Intelligent Key system under the following As many as 4 Intelligent Keys can be used with one 3. Key number plate operating conditions. vehicle. For information about the purchase and use 4. Ignition switch cap of additional Intelligent Keys, contact a NISSAN • When operating near a location where strong dealer or qualified workshop. radio waves are transmitted, such as a TV tower, power station and broadcasting station.

3-10 Pre-driving checks and adjustments CAUTION • Do not allow the Intelligent Key, which contains electrical components, to come into contact with water or salt water. This could affect the system function. • Do not drop the Intelligent Key. • Do not strike the Intelligent Key sharply against another object. • Do not place the Intelligent Key for an ex- SPA2074Z tended period in an area where temperatures exceed 60°C (140°F). OPERATING RANGE The operating range is within 80 cm (31.50 in) from j • Do not attach the Intelligent Key with a key each request switch 1. holder that contains a magnet. If the Intelligent Key is too close to the door glass, • Do not place the Intelligent Key near equip- handle or rear bumper the request switches may not ment that produces a magnetic field, such as function. a TV, audio equipment and personal comput- When the Intelligent Key is within the operating ers. range, it is possible for anyone, even someone who If an Intelligent Key is lost or stolen, NISSAN recom- does not carry the Intelligent Key, to push the re- mends erasing the ID code of that Intelligent Key quest switch to lock/unlock the doors. from the vehicle. This may prevent the unauthorised use of the Intelligent Key to operate the vehicle. For SPA2408Z information regarding the erasing procedure, contact a NISSAN dealer or qualified workshop. The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating The Intelligent Key function can be disabled. For j information about disabling the Intelligent Key func- range from the request switch 1. tion, contact a NISSAN dealer or qualified work- When the Intelligent Key battery is discharged or shop. strong radio waves are present near the operating location, the Intelligent Key system’s operating range becomes narrower, and the Intelligent Key may not function properly.

Pre-driving checks and adjustments 3-11 USING INTELLIGENT KEY SYSTEM • When the doors are open or not closed securely Lockout protection: (only the unlock function operates). To prevent the Intelligent Key from being acciden- • When the Intelligent Key battery is discharged. tally locked in the vehicle, lockout protection is equipped with the Intelligent Key system. Locking doors • When the driver’s side door is open and the 1. Turn the ignition switch to the LOCK position. Intelligent Key is inside the vehicle (including lug- 2. Carry the Intelligent Key. gage area), the doors cannot be locked using the inside lock knob or power door lock switch. 3. Close all doors (including the back door). j • When the driver’s side door is open, the doors 4. Push the door handle request switch A or back are locked, and then the Intelligent Key is put SPA2664Z j door request switch B. inside the vehicle and all the doors are closed; 5. All doors will be locked. the lock will automatically unlock and the door buzzer sounds. 6. Operate the door handles to confirm that the doors have been securely locked. When a person carrying another Intelligent Key, which has been registered to the Intelligent Key sys- CAUTION tem, enters the vehicle, the lockout protection will • After locking the doors using the request be activated and the lock function by the door handle switch, make sure that the doors have been request switch will not operate. To lock, use the securely locked by operating the door remote keyless entry function or the mechanical key. handles. CAUTION When locking the doors using the request SPA2665Z • The lockout protection may not function under switch, make sure to have the Intelligent Key the following conditions: in your possession before operating the re- The request switch will not function under the fol- quest switch to prevent the Intelligent Key • When the Intelligent Key is placed on top of lowing conditions: from being left in the vehicle. the instrument panel. • When the mechanical key is in the ignition switch. • The request switch is operational only when • When the Intelligent Key is placed on the ton- the Intelligent Key has been detected by the neau cover. • When the Intelligent Key is left inside the vehicle Intelligent Key system. (only the unlock function operates). • When the Intelligent Key is placed inside of the glove box. • When the Intelligent Key is not within the operational range. • When the Intelligent Key is placed inside of the door pockets.

3-12 Pre-driving checks and adjustments • When the Intelligent Key is placed inside the that door may not be unlocked. Returning the door Perform the same procedure to deactivate the se- metal box. handle to its original position will unlock the door. If lective door unlock mode. the door does not unlock, after returning the door The lockout protection may function when the handle, push the door handle request switch to un- USING REMOTE KEYLESS ENTRY Intelligent Key is outside the vehicle but is too lock the door. FUNCTION close to the vehicle. All doors will be locked automatically unless one of Unlocking doors the following operations is performed within 2 min- All door unlock mode: utes after pushing the request switch while the doors 1. Carry the Intelligent Key. are locked. 2. Push the door handle request switch jA or back • Opening any door or back door. door request switch jB. • Pushing in the ignition switch. 3. All doors (including the back door) will be un- • Inserting the mechanical key into the ignition locked. switch. SPA2380AZ Selective door unlock mode: During this 2-minute time period, if the “UNLOCK” button on the Intelligent Key is pushed, all 1. Carry the Intelligent Key. j1 “LOCK” button j doors will be locked automatically after another 2 2. Push the door handle request switch A or back minutes. j2 “UNLOCK” button door request switch jB. Selecting door unlock mode: Driver’s door handle or back door request switch: WARNING When you first receive the vehicle, the door unlock Only the corresponding door will be unlocked. mode is set to unlock all the doors with one push of For Super Lock System equipped models, failure j to follow the precautions below may lead to haz- Front passenger’s door handle request switch: the door handle request switch A or back door request switch jB . The door unlock mode can be ardous situations. Make sure the Super Lock Sys- All doors (including the back door) will be un- switched to the selective door unlock mode. tem activation is always safely conducted. locked. (Selective door unlock mode is not avail- When the vehicle is occupied, never lock the able.) To switch to the selective door unlock mode, per- • form the following procedure. doors with the Intelligent Key. Doing so will 3. Push the driver’s door handle request switch jA trap the occupants, since the Super Lock Sys- or back door request switch jB again within 5 Push the “LOCK” and “UNLOCK” but- tem prevents the doors from being opened seconds. tons on the Intelligent Key simultaneously for more from the inside of the vehicle. than 10 seconds. Within 3 seconds, push the driv- All doors will be unlocked. er’s door handle request switch. • Only operate the Intelligent Key lock button when there is a clear view of the vehicle. This If a door handle is pulled while unlocking the doors,

Pre-driving checks and adjustments 3-13 is to prevent anybody from being trapped in- 5. Operate the door handles to confirm that the • Inserting the mechanical key into the ignition side the vehicle through the Supper Lock Sys- doors have been securely locked. switch. tem activation. CAUTION During this 2-minute time period, if the “UNLOCK” The remote keyless entry function can operate all After locking the doors using the Intelligent Key, button on the Intelligent Key is pushed, all door locks (including the back door lock) using the be sure that the doors have been securely locked doors will be locked automatically after another 2 remote keyless function of the Intelligent Key. The by operating the door handles. minutes. remote keyless function can operate at a distance of Selecting door unlock mode: 1 m (3.3 ft) away from the vehicle. The operating Unlocking doors distance depends upon the conditions around the When you first receive the vehicle, the door unlock All door unlock mode: vehicle. mode is set to unlock all the doors with one push of 1. Push the “UNLOCK” button j2 on the In- the “UNLOCK” button j2 . The door unlock The remote keyless entry function will not function telligent Key. mode can be switched to the selective door unlock under the following conditions: mode. 2. All doors (including the back door) will be un- • When the mechanical key is in the ignition switch. locked. To switch to the selective door unlock mode, perform the following procedure. • When the Intelligent Key is not within the opera- Selective door unlock mode: tional range. 1. Push the “UNLOCK” button j2 on the In- Push the “LOCK” and “UNLOCK” but- • When the doors are open or not closed securely. telligent Key. tons on the Intelligent Key simultaneously for more (Only the unlock function operates.) than 10 seconds. Within 3 seconds, push the driv- 2. The driver’s door will be unlocked. er’s door handle request switch. • When the Intelligent Key battery is discharged. 3. Push the “UNLOCK” button on the Intelli- Perform the same procedure to deactivate the se- CAUTION gent Key again. lective door unlock mode. When locking the doors using the Intelligent Key, 4. All doors (including the back door) will be un- be sure not to leave the key in the vehicle. locked. Locking doors All doors will be locked automatically unless one of 1. Turn the ignition switch to the LOCK position. the following operations is performed within 2 minutes after pushing the “UNLOCK” button on the 2. Close all doors (including the back door). Intelligent Key while the doors are locked. j 3. Push the “LOCK” button 1 on the Intelli- • Opening any door. gent Key. • Pushing in the ignition switch. 4. All doors will be locked.

3-14 Pre-driving checks and adjustments WARNING LIGHTS AND AUDIBLE and controls” section and “Vehicle information REMINDERS display” in the “2. Instruments and controls” section.

SPA2666Z j1 Intelligent Key system warning light j2 Intelligent Key lock warning light j3 NO KEY warning j4 Key battery discharge indicator j5 LOCK warning The Intelligent Key system is equipped with a function that is designed to minimise improper operations and to help prevent the vehicle from being stolen. The warning buzzer sounds and the warning illuminates when improper operations are detected. CAUTION When the buzzer sounds and the warning light illuminates, be sure to check both the vehicle and the Intelligent Key. For additional information, see “Warning/indicator lights and audible reminders” in the “2. Instruments

Pre-driving checks and adjustments 3-15 Troubleshooting guide

Warnings What to check What to do Take the Intelligent Key from inside the vehicle or luggage area Has the Intelligent Key been left inside of the vehicle and securely close all the doors. or luggage area? Push the request switch while holding the Intelligent Key. Return the ignition switch to the LOCK position and securely Has the ignition switch been returned to the LOCK The outside buzzer sounds short close all the doors. position? continuous beeps when operating Push the request switch while holding the Intelligent Key. the request switch. Are the doors closed completely before pushing the Close all the doors securely. request switch? Push the request switch while holding the Intelligent Key. Is the mechanical key inserted into the ignition Remove the mechanical key from the ignition switch. switch? The outside buzzer sounds short Return the ignition switch to the LOCK position and securely continuous beeps and the Intel- Has the ignition switch returned to the LOCK posi- close all the doors. ligent Key lock warning light blinks tion? Push the door handle request switch while holding the Intelligent in red when closing the driver’s Key. door. The outside buzzer sounds short Check the location of the Intelligent Key. continuous beeps and the Intel- Has the Intelligent Key been brought outside the The Intelligent Key must be carried by the driver when operating ligent Key system warning light vehicle? the vehicle. blinks in red. The inside buzzer sounds two short Has the ignition switch returned to the LOCK posi- beeps and the Intelligent Key lock Return the ignition switch to the LOCK position. tion? warning light blinks in red. Has the ignition switch returned to the LOCK posi- Return the ignition switch to the LOCK position. The inside buzzer sounds short tion? beeps for 5 seconds when opening Is the mechanical key inserted into the ignition the driver’s door. Remove the mechanical key from the ignition switch. switch?

3-16 Pre-driving checks and adjustments Warnings What to check What to do The Intelligent Key system warning Replace the Intelligent Key battery with a new one. (See Is the Intelligent Key battery good? light blinks in green. “Battery” in the “8. Maintenance and do-it-yourself” section.) The Intelligent Key system warning Carry the Intelligent Key. If the warning light stays on in red, light illuminates in red when push- Are you carrying the Intelligent Key? replace the Intelligent Key battery with a new one. (See “Battery” ing the ignition switch. in the “8. Maintenance and do-it-yourself” section.)

Pre-driving checks and adjustments 3-17 SECURITY SYSTEM

Your vehicle is equipped with the NISSAN Anti-theft recommends placing the registered key separate will illuminate when the ignition switch is in the ON System (NATS)*. from other devices to avoid interference. position. However, if the security indicator light turns off after 15 minutes, you can start the engine once. (* immobilizer) See a NISSAN dealer or qualified workshop for NISSAN ANTI-THEFT SYSTEM (NATS) NATS service as soon as possible. The NISSAN Anti-Theft System (NATS) will not allow the engine to start without the use of the registered NATS key, integrated keyfob or Intelligent Key. If the engine does not start using the registered key, it may be due to interference caused by:

• Another NATS key, integrated keyfob or Intelli- SIC2045Z gent Key. • Automated toll road device. Security indicator light • Automated payment device. The security indicator light is located on the meter • Other devices that transmit similar signals. panel. It indicates the status of NATS. Start the engine using the following procedure: The light operates whenever the ignition switch is in the LOCK, “OFF” or ACC position. The security 1. Remove any items that may be causing the inter- indicator light indicates that the security systems on ference away from the key. the vehicle are operational. 2. Leave the ignition switch in the ON position for If NATS is malfunctioning, this light will remain on approximately 5 seconds. while the ignition switch is in the ON position. 3. Turn the ignition switch to the “OFF” or LOCK If the light remains on and/or the engine does position, and wait approximately 10 seconds. not start, contact a NISSAN dealer or qualified 4. Repeat steps 2 and 3 again. workshop for NATS service as soon as possible. Be sure to bring all keys that you have when vis- 5. Start the engine. iting a NISSAN dealer or qualified workshop for 6. Repeat the steps above until all possible interfer- service. ences are eliminated. For Right-Hand Drive (RHD) model: If this procedure allows the engine to start, NISSAN If NATS is malfunctioning, the security indicator light

3-18 Pre-driving checks and adjustments BONNET

WARNING • The bonnet must be closed and latched securely before driving. Failure to do so could cause the bonnet to fly open and result in an accident. • Never open the bonnet if steam or smoke is coming from the engine compartment to avoid injury. SPA2667Z

OPENING BONNET 1. Pull the bonnet lock release handle j1 located below the instrument panel until the bonnet springs up. 2. Locate the lever j2 in between the bonnet and grille and pull the lever up with your fingertips. 3. Raise the bonnet j3. 4. Remove the support rod j4 and insert it into the slot j5. Hold the coated parts jA when removing or resetting the support rod. Avoid direct contact with the metal parts, as they may be hot immediately after the engine has been stopped. CLOSING BONNET 1. Reset the support rod to its original position. 2. Slowly move the bonnet down to latch the lock. Push the bonnet down to lock the bonnet securely into place.

Pre-driving checks and adjustments 3-19 BACK DOOR

WARNING Model with integrated keyfob or TAILGATE Intelligent Key • Make sure the back door has been closed securely to prevent it from opening while driv- The back door can be locked or unlocked with one ing. of the following operations. • Do not drive with the back door open. This • Push the “LOCK” or “UNLOCK” but- could allow dangerous exhaust gases to be ton on the integrated keyfob or the Intelligent drawn into the vehicle. Key (where fitted). (See “Remote keyless entry system (where fitted)” earlier in this section or LOCKING OR UNLOCKING BACK “Intelligent Key system (where fitted)” earlier in this section.) In selective unlock mode, push the DOOR SPA2669Z “UNLOCK” button twice to unlock the back door. • Push any of the request switches (where fitted). Opening back door (See “Intelligent Key system (where fitted)” ear- Pull the back door opener handle j1 and lift up the lier in this section.) In selective unlock mode, the back door to fully open. driver’s door handle request switch needs to be pushed twice to unlock the back door. To close the back door, pull down until it securely locks. • Push the power door lock switch to the lock or unlock position. SPA2696Z With key cylinder • Lock or unlock the driver’s door lock with the key or the inside door lock knob. Model with key cylinder Insert the key to the back door key cylinder and turn the key clockwise j1 to lock the back door. Turn the key anticlockwise j2 to unlock the back door.

3-20 Pre-driving checks and adjustments FRENCH DOORS

SPA2699Z SPA2700Z

SPA2697Z 3. To fully open the back door (180-degrees), pull Opening back door from inside The right-side back door cannot be opened when the lever j3 located on the inside of each back To open the back door from the inside of the ve- the left-side back door is closed. door. The back doors are not designed to be latched in their fully open positions. hicle, pull the inside handle on the left-side back Opening back door from outside door. Park the vehicle in a safe and level place. Make 1. Pull the back door opener handle j1 to open the sure that the area is clear of obstacles and there left-side back door. is enough clearance around the back doors. CAUTION • Always look before fully opening the back door(s), to avoid an accident with oncoming traffic or pedestrians. • When closing the back doors, be sure to close the right-side door before closing the left-side door.

SPA2698Z

2. To open the right-side back door, pull the lever j2 located on the lower side of it.

Pre-driving checks and adjustments 3-21 FUEL FILLER LID

OPENING FUEL FILLER LID Put the tether strap of the fuel filler cap on the hook WARNING jA while refuelling. • Fuel is extremely flammable and highly explo- CAUTION sive under certain conditions. You could be burned or seriously injured if it is misused or If fuel is spilled on the vehicle body, flush it away mishandled. Always stop the engine and do with water to avoid paint damage. not smoke or allow open flames or sparks near the vehicle when refuelling. • Fuel may be under pressure. Turn the cap a half of a turn, and wait for any “hissing” sound

to stop to prevent fuel from spraying out and SPA2336Z possibly causing personal injury. Then remove the cap. To open the fuel filler lid, pull the fuel filler lid release • Use only an original equipment type fuel filler handle. cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel FUEL FILLER CAP system and emission control system. An incorrect cap can result in a serious malfunction and possible injury.

SPA2668Z

The fuel filler cap is a ratcheting type. Turn the cap anticlockwise j1 to remove. After refuelling, tighten the cap clockwise j2 until the ratchet clicks more than two times.

3-22 Pre-driving checks and adjustments STEERING WHEEL MIRRORS

• Objects viewed in the outside mirror are WARNING WARNING closer than they appear. Never adjust the steering wheel while driving so Adjust the position of all mirrors before driving. • The picture dimensions and distance in the that full attention may be given to vehicle opera- Do not adjust the mirror positions while driving outside mirrors are not real. tion. so that full attention may be given to vehicle operation. TILT OPERATION INSIDE REARVIEW MIRROR (where fitted)

SPA2214Z

SPA1527Z Adjusting Remote control type: Pull the lock lever up j1 and adjust the steering SPA2447Z wheel up or down j2 until the desired position is The outside rearview mirror remote control operates when the ignition switch is in the ACC or ON posi- achieved. While holding the inside rearview mirror, adjust the tion. j mirror angles until the desired position is achieved. Push the lock lever down 3 firmly to lock the steer- j j ing wheel in place. 1. Move the switch to select the right 1 or left 2 OUTSIDE REARVIEW MIRRORS mirror.

WARNING 2. Adjust each mirror by pushing the switch until the desired position is achieved j2. • Never touch the outside rearview mirrors while they are in motion. Doing so may pinch your fingers or damage the mirror. • Never drive the vehicle with the outside rearview mirrors folded. This reduces rear view visibility and may lead to an accident.

Pre-driving checks and adjustments 3-23 PARKING BRAKE

Folding WARNING Manual control type: • Never drive the vehicle with the parking brake Fold the outside rearview mirror by pushing it to- applied. The brake will overheat and fail to ward the rear of the vehicle. operate and will lead to an accident. • Never release the parking brake from outside the vehicle. If the vehicle moves, it will be impossible to push the footbrake pedal and will lead to an accident. SPA2242Z • Never use the gearshift in place of the parking brake. When parking, be sure the parking Manual control type: brake is fully applied. The outside mirror can be moved in any direction for • Never leave children or adults who would nor- a better rear view. mally require the support of others alone in your vehicle. They could unknowingly release Defogging (where fitted) the parking brake and inadvertently become The outside rearview mirrors will be heated when involved in a serious accident. the rear window defogger switch is operated. LEVER TYPE

SPA0701Z SPA2110Z

To apply the parking brake, pull the parking brake lever up j1.

3-24 Pre-driving checks and adjustments To release the parking brake, firmly depress and hold the footbrake pedal. Pull up the parking brake lever slightly, push the button j2 and lower the lever completely j3. Before driving, be sure that the brake warning light has turned off.

Pre-driving checks and adjustments 3-25 NOTE

3-26 Pre-driving checks and adjustments 4 Display screen, heater and air conditioner, and audio system

Safety precautions ...... 4-2 Manual air conditioner...... 4-5 Rear view monitor (where fitted)...... 4-2 Rear cooler (where fitted) ...... 4-7 How to read the displayed lines ...... 4-2 Servicing air conditioner ...... 4-7 Operating tips...... 4-3 Audio system (where fitted)...... 4-8 Vents...... 4-4 Audio operation precautions ...... 4-8 Centre vents...... 4-4 Antenna...... 4-9 Side vents ...... 4-4 CD Player/LW-MW-FM radio ...... 4-10 Rear vents ...... 4-4 Car phone or CB radio ...... 4-16 Heater and air conditioner...... 4-4 SAFETY PRECAUTIONS REAR VIEW MONITOR (where fitted)

When the shift lever is moved into the R (Reverse) • When washing the vehicle with high-pressure WARNING position, the monitor display shows view to the rear water, be sure not to spray it around the cam- • Do not adjust the heater and air conditioner of the vehicle. era. Otherwise, water may enter the camera unit causing water condensation on the lens, controls or audio controls while driving so that The system is designed as an aid to the driver in a malfunction, fire or an electric shock. full attention may be given to vehicle opera- detecting large stationary objects to help avoid dam- tion. aging the vehicle. The system will not detect small • Do not strike the camera. It is a precision in- • If you noticed any foreign objects entering the objects below the bumper and may not detect ob- strument. Otherwise, it may malfunction or system hardware, spilled liquid on the sys- jects close to the bumper or on the ground. cause damage resulting in a fire or an electric tem, or noticed smoke or fumes coming out shock. from the system, or any other unusual opera- WARNING CAUTION tion is observed, stop using the system imme- The rear view camera is a convenience but it diately and contact the nearest NISSAN dealer • There is a plastic cover over the camera. Do not is not a substitute for proper reversing. Al- or qualified workshop. Ignoring such condi- scratch the cover when cleaning dirt or snow from ways turn and check that it is safe to do so tions may lead to an accident, fire or electric the cover. before reversing. Always reverse slowly. shock. HOW TO READ THE DISPLAYED Objects viewed in the rear view monitor differ Do not disassemble or modify this system. If • • from actual distance because a wide-angle LINES you do, it may lead to an accident, fire, or lens is used. electric shock. Objects viewed in the rear view monitor ap- Park the vehicle in a safe location and apply • • pear visually opposite, just like ones viewed the parking brake to view images on the front in the inside and outside rearview mirrors. centre display screen using devices connected to the auxiliary input jacks. • Make sure that the back door is securely closed when reversing. CAUTION Underneath the bumper and the corner areas Do not use the system when the engine is not • of the bumper cannot be viewed on the rear running for extended periods of time to prevent view monitor because of its monitoring range SAA0889Z battery discharge. limitation. • Do not put anything on the rear view camera. WARNING The rear view camera is installed above the number plate. • Use the displayed lines as a reference. The lines are highly affected by the number of occupants, fuel level, vehicle position, road con-

4-2 Display screen, heater and air conditioner, and audio system dition and road grade. Always check with your • It may take some time until the rear view monitor clean the camera, wipe with a cloth dampened eyes directly around the vehicle while revers- or the normal screen is displayed after the shift with diluted mild cleaning agent and then wipe ing. lever has been shifted to R (Reverse) from an- with a dry cloth. other position or to another position from R (Re- The distance guide line and the vehicle width Do not damage the camera as the monitor screen • verse). Objects may be distorted momentarily • line should be used as a reference only when may be adversely affected. until the rear view monitor screen is displayed the vehicle is on a level paved surface. The completely. Do not use wax on the camera window. Wipe off distance viewed on the monitor is for refer- • any wax with a clean cloth dampened with mild ence only and may be different than the ac- When the temperature is extremely high or low, • detergent diluted with water. tual distance between the vehicle and dis- the screen may not clearly display objects. This played objects. is not a malfunction. • When reversing the vehicle up a hill, objects • When strong light directly enters the camera, viewed in the monitor are further than they objects may not be displayed clearly. This is not appear. When reversing the vehicle down a a malfunction. hill, objects viewed in the monitor are closer Vertical lines may be seen in objects on the than they appear. Use the inside mirror or • screen. This is due to strong reflected light from glance over your shoulder to properly judge the bumper. This is not a malfunction. distances to other objects. The screen may flicker under fluorescent light. Guiding lines which indicate the vehicle width and • This is not a malfunction. distances to objects with reference to the bumper line jA are displayed on the monitor. • The colours of objects on the rear view monitor may differ somewhat from those of the actual They are indicated as reference distances to ob- object. jects. Displayed lines indicate distances 0.5 m (red) j1 , 1 m (yellow) j2 , 2 m (green) j3 and3m(green) • Objects on the monitor may not be clear in a j4 [1.5 feet (red), 3 feet (yellow), 7 feet (green) and dark place or at night. This is not a malfunction. 10 feet (green)] from the lower part of the bumper If dirt, rain or snow attaches to the camera, the line j • A. rear view monitor may not clearly display ob- OPERATING TIPS jects. Clean the camera. • When the shift lever is shifted to R (Reverse), the • Do not use alcohol, benzine or thinner to clean monitor screen automatically changes to the rear the camera. This will cause discolouration. To view monitor mode. However, the radio can be heard.

Display screen, heater and air conditioner, and audio system 4-3 VENTS HEATER AND AIR CONDITIONER

CENTRE VENTS SIDE VENTS WARNING • The heater and air conditioner operate only when the engine is running. • Never leave children or adults who would normally require the support of others alone in the vehicle. Pets should not be left alone either. They could unknowingly activate switches or controls and inadvertently become involved in a serious accident and

SAA2383Z SAA2381Z injure themselves. On hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or pos- Open/close the vents by moving the control to ei- Open or close the vents, and adjust the air flow sibly fatal injuries to people or animals. ther direction. direction of vents as illustrated. Do not use the recirculation mode for long : This symbol indicates that the vents are • REAR VENTS periods as it may cause the interior air to be- closed. Moving the control to this direc- come stale and the windows to fog up. tion will close the vents. : This symbol indicates that the vents are • Do not adjust the heating and air conditioning open. Moving the control to this direction controls while driving so that full attention may will open the vents. be given to vehicle operation. Adjust the air flow direction of the vents by moving NOTE the centre knob (up/down, left/right) until the de- Condensation forms inside the air conditioning sired position is achieved. unit when the air conditioner is running, and is safely discharged underneath your vehicle. SAA2382Z Traces of water on the ground are therefore normal. Adjust the air flow direction of the vents by moving the centre knob (up/down, left/right) until the de- The heater and air conditioner operate when the sired position is achieved. engine is running. The air blower will operate even if the engine is turned off and the ignition switch is in the ON position.

4-4 Display screen, heater and air conditioner, and audio system A/C (Air Conditioner) operation (where fitted): Push the “A/C” button to turn the air conditioner on or off. When the air conditioner is on, the “A/C” indicator light on the button illuminates. Temperature control: Turn the temperature control dial to set the desired temperature. Turn the dial between the middle and the right position to select the hot temperature. Turn the dial between the middle and the left position to SAA2587Z select the cool temperature. Heater operation MANUAL AIR CONDITIONER Air flow control: Heating: 1. Air intake lever (Outside air circulation “ ” Turn the air flow control dial to change the air flow /Air recirculation “ ”) mode. This mode is used to direct heated air to the foot — Air flows from the centre and side vents. outlets. 2. Air flow control dial — Air flows from the centre and side vents 1. Move the air intake lever to the “ ” position 3. Fan speed control “ ” dial and foot outlets. for normal heating. 4. “A/C” (Air Conditioner) button (where fitted) — Air flows mainly from the foot outlets. 2. Turn the air flow control dial to the “ ” posi- 5. Temperature control dial — Air flows from the defogger and foot out- tion. lets. To turn off the heater and air conditioner, turn the 3. Turn the fan speed control “ ”dialtothe — Air flows mainly from the defogger out- desired position. fan speed control “ ” dial to the “OFF” (0) posi- lets. tion. 4. Turn the temperature control dial to the desired Fan speed control: Controls position between the middle and the hot (right) Turn the fan speed control “ ” dial clockwise to position. Outside air circulation: increase the fan speed. Ventilation: Move the air intake lever to the “ ” position. The Turn the fan speed control “ ” dial anticlockwise air flow is drawn from outside the vehicle. This mode directs outside air to the side and centre to decrease the fan speed. vents. Air recirculation: 1. Move the air intake lever to the “ ” position. Move the air intake lever to the “ ” position. The air flow is circulated inside the vehicle.

Display screen, heater and air conditioner, and audio system 4-5 2. Turn the air flow control dial to the “ ” posi- 1. Move the air intake lever to the “ ” position. 3. Turn the fan speed control “ ”dialtothe tion. desired position. 2. Turn the air flow control dial to the “ ” posi- 3. Turn the fan speed control “ ” dial to the tion. 4. Push the “A/C” button on. (The “A/C” indicator desired position. light will illuminate.) 3. Turn the fan speed control “ ” dial to the 4. Turn the temperature control dial to the desired desired position. 5. Turn the temperature control dial to the desired position. position between the middle and the cool (left) 4. Turn the temperature control dial to the desired position. Defrosting or defogging: position. This mode directs the air to the defogger outlets to Heating and defogging: A visible mist may be seen coming from the vents in defrost/defog the windows. hot, humid conditions as the air is cooled rapidly. This mode heats the interior and defogs the win- This does not indicate a malfunction. 1. Move the air intake lever to the “ ” position. dows. Dehumidified heating: 2. Turn the air flow control dial to the “ ” posi- 1. Move the air intake lever to the “ ” position. This mode is used to heat and dehumidify the air. tion. 2. Turn the air flow control dial to the “ ” posi- 1. Move the air intake lever to the “ ” position. 3. Turn the fan speed control “ ” dial to the tion. desired position. 2. Turn the air flow control dial to the “ ” posi- 3. Turn the fan speed control “ ” dial to the tion. 4. Turn the temperature control dial to the desired desired position. position between the middle and the hot (right) 3. Turn the fan speed control “ ”dialtothe 4. Turn the temperature control dial to the maximum position. desired position. hot (right) position. • To remove frost from the outside surface of the 4. Push the “A/C” button on. (The “A/C” indicator windscreen quickly, turn the temperature control Air conditioner operation (where fitted) light will illuminate.) dial to the maximum hot position and the fan The air conditioner system should be operated for 5. Turn the temperature control dial to the desired speed control “ ” dial to maximum position. approximately 10 minutes at least once a month. position between the middle and the hot (right) This helps prevent damage to the air conditioner If it is difficult to defog the windscreen, turn the position. • system due to the lack of lubrication. “A/C” button on (where fitted). Dehumidified defogging: Cooling: Bi-level heating: This mode is used to defog the windows and dehu- This mode is used to cool and dehumidify the air. This mode directs cool air from the side and centre midify the air. vents and warm air from the foot outlets. When the 1. Move the air intake lever to the “ ” position. 1. Move the air intake lever to the “ ” position. temperature control dial is turned to the maximum 2. Turn the air flow control dial to the “ ” posi- hot or cool position, the air between the vents and 2. Turn the air flow control dial to the “ ” position. the foot outlets is the same temperature. tion.

4-6 Display screen, heater and air conditioner, and audio system 3. Turn the fan speed control “ ” dial to the quired when servicing your vehicle’s air conditioner. desired position. Using improper refrigerants or lubricants will cause severe damage to the air conditioner system. (See 4. Push the “A/C” button on. (The “A/C” indicator “Air conditioner system refrigerant and lubricant” in light will illuminate.) the “9. Technical information” section.) 5. Turn the temperature control dial to the desired A NISSAN dealer or qualified workshop will be able position. to service your environmentally friendly air condi- REAR COOLER (where fitted) tioner system. Air conditioner filter (where fitted) SAA2384Z Rear cooler fan switch The air conditioner system is equipped with an air j conditioner filter which collects dirt, pollen, dust, 4. Turn the rear cooler fan switch 2 (located on etc. To make sure the air conditioner heats, defogs, the side of the third row seat) to the desired posi- and ventilates efficiently, replace the filter according tion to select the fan speed. to the specified maintenance intervals listed in a SERVICING AIR CONDITIONER separate maintenance booklet. To replace the filter, contact a NISSAN dealer or qualified workshop.

SAA0908Z WARNING The filter should be replaced if the air flow decreases Rear cooler front switch The air conditioner system contains refrigerant significantly or if windows fog up easily when operating the heater or air conditioner. To activate the rear cooler, take the following steps. under high pressure. To avoid personal injury, any air conditioner service should be done only 1. Start the engine. by an experienced technician with the proper 2. Operate the front air conditioner. equipment. Rear cooler function operates only when the The air conditioner system in your vehicle is charged engine is running and the front air conditioner with a refrigerant designed with the environment in is operating. mind. 3. Push the rear cooler front switch j1 (located on NISSAN GREEN PROGRAM the instrument panel) to the ON position. (The This refrigerant will not harm the earth’s ozone indicator light jA will illuminate.) layer. However, it may contribute in a small part to global warming. Special charging equipment and lubricant are re-

Display screen, heater and air conditioner, and audio system 4-7 AUDIO SYSTEM (where fitted)

AUDIO OPERATION PRECAUTIONS – Copy control compact discs (CCCD) – Recordable compact discs (CD-R) WARNING – Rewritable compact discs (CD-RW) Do not adjust the audio system while driving so that full attention may be given to vehicle operation. Radio • Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influences. Intermittent changes in reception quality normally are caused by these external influences. • Using a mobile phone in or near the vehicle may influence radio reception quality. Compact Disc (CD) player • During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD from CD player and dehumidify or ventilate the player completely.

• The player may skip while driving on rough roads. SAA0480 • The CD player sometimes may not function when the passenger compartment temperature is ex- • Do not use the following CDs as they may cause tremely high. Lower the temperature before use. the CD player to malfunction. • Do not expose the CD to direct sunlight. – 8 cm (3.1 in) discs with an adapter • CDs that are of poor quality, or are dirty, – CDs that are not round scratched, covered with fingerprints, or that have pin holes may not work properly. – CDs with a paper label • The following CDs may not work properly. – CDs that are warped, scratched or have unusual edges.

4-8 Display screen, heater and air conditioner, and audio system • This audio system can only play prerecorded ANTENNA To install the antenna, turn the antenna clockwise CDs. It has no capabilities to record or burn and tighten. CDs. CAUTION If the CD cannot be played, one of the following • Be sure to fold down the antenna before the messages will be displayed. • vehicle enters a garage with a low ceiling. Error CD: • Be sure that antenna is removed before the – Confirm that the CD is inserted correctly (the vehicle enters an automatic car wash. label side is facing up, etc.). – Confirm that the CD is not bent or warped and it is free of scratches. Eject CD: This is a malfunction due to the temperature inside the player being too high. Remove the CD by pushing the EJECT button, and after a short time reinsert the CD. The CD can be played when the temperature of the player returns to normal.

SAA0611

Adjust the antenna angle for the best reception. Removing antenna You can remove the antenna if necessary. Hold the bottom of the antenna and remove by turning anticlockwise.

Display screen, heater and air conditioner, and audio system 4-9 13. MIX (Mix play) button 14. RPT (Repeat) button 15. VOLUME control/MENU select dial 16. ENTER button 17. AUX jack 18. NEWS button 19. TUNE/SEARCH button CD PLAYER/LW-MW-FM RADIO Anti-theft system By using a personal 4-digit code known only to the vehicle owner, the possibility of the audio unit being stolen is effectively reduced, because without the code, the unit can not be activated. When used normally, the unit is unlocked and accessible in the usual way. If however, force is used to try and remove the unit, the anti-theft system activates and the unit locks. The only way it can be unlocked is by entering the SAA2379 personal code number known only by the owner. This code number cannot be altered and applies only to your vehicle. This code number is shown on 1. MUTE button 7. CD button a radio pass card. Ask your NISSAN dealer or quali- 2. POWER ON/OFF button 8. AUX button fied workshop for the location of your radio pass card. 3. Sound preference button 9. TA (Traffic Announcement) button 4. FM band select button 10. MENU button 5. AM band select button 11. CD EJECT button 6. Radio memory buttons 12. SEEK/TRACK button

4-10 Display screen, heater and air conditioner, and audio system is displayed. After 60 minutes, the code input Sound preference button: WARNING mode is automatically set (CODE IN is Keep the radio pass card in a safe place and displayed). If the above is repeated 17 times, the To enter the audio mode (radio or CD), push the refrain from keeping it in the vehicle. Contact unit will lock permanently and you will need to button. When no CD is loaded, the audio sys- your NISSAN dealer or qualified workshop if you contact your NISSAN dealer or qualified work- tem will automatically switch to the radio mode. shop. lose the radio pass card or forget the code num- To change the audio settings (BASS, TREBLE, ber of your radio. Audio main operation FADER, BALANCE, EQ), push the button or Unlocking the unit: ENTER button to select the mode. The audio system operates when the ignition switch CAUTION is in the ACC or ON position. BASS → TREBLE → BALANCE → FADER → EQ → BASS Read this section very carefully. It is important m POWER ON/OFF button: that the instructions are followed precisely. To adjust each audio setting, turn the MENU/VOL To turn on the audio system, push the POWER control dial clockwise or anticlockwise. If the battery supply to the vehicle is interrupted by ON/OFF button. accident for some reason, the unit will lock. BASS: (−) to decrease / (+) to increase The system will turn on in the mode, (radio or TREB(LE): (−) to decrease / (+) to increase To unlock the unit, proceed as follows: • CD) which was used immediately before the sys- BAL(ANCE): (R) to right balance / (L) to left bal- 1. Press the power/volume control knob to turn the tem was turned off. ance unit on. • If there is no CD loaded, the radio will be turned FADE(R): (F) to front fade / (R) to rear fade 2. CODE IN is displayed. on. EQ (Equalizer): 3. Input your personal code by pressing the preset To turn off the audio system, push the POWER Use this control to change the preset sound mode buttons (1 to 4). ON/OFF button. for CD play. 4. Press the or button. Volume control: Turn the MENU/VOL dial clockwise or anticlockwise. The mode will change as follows: 5. If the entered code number is correct, the radio To control the volume, turn the VOLUME control turns on. A radio frequency appears on the dis- dial. OFF ⇔ ENHANCE play. Turn the VOLUME control dial clockwise to make If the audio settings mode is unchanged for approxi- 6. If the entered code is incorrect, the unit becomes the sound louder. mately 8 seconds, the audio settings mode will automatically return to the normal mode. inoperable for 10 seconds for the first three at- Turn the VOLUME control dial anticlockwise to tempts, then the code input mode is automati- make the sound quieter. cally set (CODE IN is displayed). 7. If the code is incorrect the fourth time, the unit becomes inoperable for 60 minutes and ( )

Display screen, heater and air conditioner, and audio system 4-11 m Mute button: To change the radio bands, push the / j1 j2 j3 j4 j5 j6 Radio memory buttons: button until the desired band appears. The audio system can store up to 18 FM station fre- Push the button to mute the audio system, and / button: quencies (six in each of FM 1, FM 2 and FM T), 6 MUTE appears on the display. To cancel the mute MW and 6 LW station frequencies. mode, use any one of the following options: • For FM To store the station frequency manually: – Push the button again. FM 1 → FM 2 → FM T 1. Tune to the desired broadcasting station fre- – Turn the MENU/VOL knob. • For AM quency by using the or – Push the CD, FM or AM button. MW → LW → MW button. – Push the AUX button. During FM reception, when the button is 2. Push and hold a radio memory button j1-j6 pushed for longer than 1.5 seconds, stations are until a beep sounds. (The radio mutes when the searched for and the 6 strongest stations of the FM memory button is pushed.) T band are stored. The sound is muted until the auto 3. The channel indicator will display and the radio store operation is completed, upon which preset mute disengages, indicating that the memory is channel 1 is automatically tuned in. stored properly. TUNE button: 4. Perform steps1-3forallothermemorybuttons. When adjusting the broadcasting station frequency If the battery cable is disconnected, or if the audio manually, push the or button until the fuse blows, the radio memory will be erased. In

SAA2380Z desired frequency is achieved. such a case, reset the desired stations. The frequency changes in steps of 100 kHz on the Radio data system (RDS) FM band, 9 kHz on the MW band, and 3 kHz on the LW-MW-FM radio operation Alternative Frequency (AF): LW band. The audio system operates when the ignition switch The AF function operates in the FM (radio) and m SEEK button: • is in the ACC or ON position. CD modes. FM-AM button: When adjusting the broadcasting station frequency • When the AF mode is set to ON in the user automatically, push the or button. When setup menu mode, the AF indicator illuminates. When the / button is pushed while the the system detects a broadcasting station, it will For activation or deactivation details, see “MENU audio system is off, the audio system will turn on stop at the station. button” later in this section. and the radio will turn on. When the / button is pushed while CD is already operating, it will automatically turn off, and the radio will turn on.

4-12 Display screen, heater and air conditioner, and audio system • Automatic switching function • Emergency broadcast interrupt function • The TA mode operates regardless of whether (ALARM INTERRUPTION — EBU SPEC FOR the AF mode is on or off. This function compares the strengths of the sig- INFO) nals of all the stations on the AF list and selects • “TA ON” is displayed when the TA mode is the station with the optimum reception condi- When the radio receives PTY code 31 (an emer- turned on, and the TA indicator turns on. “TA tions. gency broadcast code), the sound is interrupted, OFF” is displayed when the TA mode is turned the emergency broadcast is heard, and “PTY31 off, and the TA indicator turns off. Programme Information (PI) search • ALARM” is displayed. The volume level at this The following functions operate when the TA mode Programme Information (PI) search begins auto- time is the same as that for traffic announce- is on: matically if no suitable station is found with the ments. Once the emergency broadcast is fin- above automatic switching function. The PI ished, the unit immediately returns to the previ- • Traffic announcement interrupt function search function checks each RDS station with ous source. When a traffic announcement is received, the the same PI code. During this time the sound is REG (Regional) mode announcement is tuned in and the volume in- muted and “PI SEARCH” is displayed. The PI • creases to the set level. search operation stops when a suitable station is Some local radio stations are linked together ac- found. If no station is found once all the frequen- cording to their region because they only offer Once the traffic announcement is finished, the cies have been searched, the radio returns to limited coverage due to their limited number of unit returns to the source which was set before the previous frequency. transmitters. If the signal from one station be- the traffic announcement started, and the vol- comes weak while you are driving around, RDS ume returns to the previous level. For EON sta- Enhanced Other Network (EON) data update • mode will switch to another local station in the tions, the radio is interrupted by another EON (This function also operates when the AF region with a stronger signal. station with traffic announcements. mode is off.) When the REG mode is activated in the FM band The traffic announcement interrupt mode is can- When EON data is being received, this enables and the radio receiver is tuned to a local radio celled if the TA is pushed during a traffic an- automatic retuning of other preset stations on station, it will keep receiving this radio station nouncement. The TA mode returns to the the same network. Also, network linked services without switching to another local station. For standby mode and the audio unit returns to the can be used. The EON indicator turns on during activation or deactivation details, see “MENU previous source. the reception of RDS EON stations in the FM button” later in this section. mode. News mode Traffic Announcement (TA): RDS functions: When the button is pushed in the FM mode, The TA function operates in the FM and CD Programme Service (PS) function (station • the news function is activated. “NEWS” is displayed • modes. name display function) for 3 seconds and the NEWS indicator appears on The TA mode is turned on or off when the TA the display. When an RDS station is tuned in with seek or • button is pushed. manual tuning, the RDS data is received and the When the news function is activated, the radio re- Programme Service (PS) name is displayed. ceives a news code from the FM broadcasting news

Display screen, heater and air conditioner, and audio system 4-13 station and the actual playing mode will be inter- MENU button: After selecting the desired language, push the rupted. Once the news broadcast is finished, the To configure Alternative Frequency, Regional and ENTER button to exit the menu. unit returns to the previous mode. Language settings, perform the following proce- To configure the SPEED volume and BEEP set- In some countries or regions, this service is not dure: tings, perform the following procedure: available or the signal is too weak to be received. 1) Push and hold the MENU button for at least 1.5 1) Push the MENU button. 1. News standby mode seconds. 2) Turn the MENU/VOL dial clockwise or anticlock- • The news standby mode can be activated in 2) Turn the MENU/VOL dial clockwise or anticlockwise. The display message will change as fol- the FM or CD mode. wise. The display message will change as follows: lows: • A news interruption will be announced and SPEED VOL ⇔ CLOCK ⇔ BEEP ⇔ SPEED “NEWS” will be displayed when the radio de- AF ⇔ REG ⇔ LANGUAGE ⇔ AF VOL tects the news code from the tuned station or To activate or deactivate the AF and REG mode, When SPEED VOL appears on the display, EON stations. The display will then change to • • briefly push on the ENTER button when AF or briefly push on the ENTER button then turn the the PS name of the interrupting station. REG appears on the display and turn the MENU/ MENU/VOL dial clockwise or anticlockwise to • When pushing the button, the news VOL dial clockwise or anticlockwise to switch adjust the level of the volume. standby mode is turned off and the indicator between the off or on position. After selection, Adjusting the setting to 0 (zero) turns off the disappears from the display. push the ENTER button to confirm the settings. speed volume feature. Increasing the speed vol- 2. News interruption mode – When the AF mode is enabled, the audio unit ume setting results in the audio volume increas- will automatically re-tune to a stronger fre- ing more rapidly with vehicle speed. Push the When the button is pushed during the • quency if the radio signal becomes weak. ENTER button again to save the setting. news interruption mode, the radio returns to the previous source. However, the news – When the REG mode is enabled, the audio • For clock adjustment, see “Clock” in the “2. In- standby mode is kept. unit will maintain and hold the station which is struments and controls” section. broadcasting local (regional) programmes. • When the button is pushed during the • When BEEP appears on the display, briefly push news interruption mode, the radio changes to • To change the display language, briefly push the the ENTER button and then turn the MENU/VOL the CD mode. However, the news standby ENTER button when LANGUAGE appears on dial clockwise or anticlockwise to switch the mode is kept. the display then turn the MENU/VOL dial clock- beep sound on or off. Push the ENTER button wise or anticlockwise to select the appropriate again to save the setting. If the radio band is changed to the MW or language setting. LW, the news standby mode will be turned After the desired levels have been set, push the off. ENGLISH ⇔ DUTCH ⇔ FRENCH ⇔ SPAN- MENU button to exit the menu or wait at least for 10 ISH ⇔ GERMAN ⇔ ITALIAN ⇔ PORTU- seconds without pressing any buttons. GUESE ⇔ ENGLISH

4-14 Display screen, heater and air conditioner, and audio system CD button: Repeat button:

When the button is pushed while the audio Push the button repeatedly to change the play system is off and a CD is loaded, the audio system mode as follows: will turn on and a CD will start playing automatically. RPT (REPEAT) TRACK → RPT (REPEAT) ALL If the radio is already playing, it will automatically turn off and the CD will start playing. RPT TRACK: The CD player plays the current track continuously. FF (Fast Forward), REW (Rewind) button: RPT ALL: All the tracks on the CD will be played in sequential order. SAA2380Z When the (fast forward) or (rewind) button is pushed while the CD is being played, the CD will play while MIX button: fast forwarding or rewinding. When the button is CD player operation released, the CD will return to normal play speed. Push the button repeatedly to change the play mode as follows: The audio system operates when the ignition switch m TRACK UP/ DOWN button: is in the ACC or ON position. MIX DISC → RPT ALL → MIX DISC Loading: When the button is pushed while a CD is MIX DISC: All the tracks on the CD will be played being played, the present track will be advanced in a random order. Insert a CD into the slot with the label side facing and move to the next track. Push the button RPT ALL: All the tracks on the CD will be played up. The CD will be guided automatically into the slot several times to skip forward tracks. The CD will in sequential order. and will start playing. If the radio is already playing, advance the number of times the button is pushed. it will automatically turn off, and the CD will start m CD EJECT button: When the last track of the CD is forwarded, the first playing. track will be played. When the button is pushed while a CD is CAUTION When the button is pushed while a CD is loaded, the CD will be ejected. Do not force the CD into the slot. This could dam- being played, the present track will start over from When the button is pushed twice, the CD will age the player. the beginning. Push the button several times be ejected further, and the CD can be removed with to skip back tracks. The CD will rewind the number After loading the CD, the number of tracks and the ease. of times the button is pushed. When the first track playtime will appear on the display. of the CD is rewound, the last track will be played. If a CD is ejected by pushing the button, and it is not taken out from the loading slot, the CD will automatically be reloaded to the slot to protect the CD.

Display screen, heater and air conditioner, and audio system 4-15 CAR PHONE OR CB RADIO

AUX button: When installing a CB, ham radio or a car phone in your vehicle, be sure to observe the following cau- The AUX IN jack is located on the audio unit. The tions, otherwise the new equipment may adversely AUX IN audio input jack accepts any standard ana- affect the Engine Control System and other elec- log audio input such as from a portable cassette tronic parts. tape/CD player, MP3 player, laptop computers, etc. CAUTION Push the button to play a compatible device Keep the antenna as far away as possible from when it is plugged into the AUX IN jack. • the Electronic Control Module. • Keep the antenna wire at least 20 cm (8 in) away from the Engine Control harnesses. Do not route the antenna wire next to any harnesses. • Adjust the antenna standing wave ratio as recommended by the manufacturer. • Connect the ground wire from the radio chassis to the body. • For details, consult a NISSAN dealer or qualified workshop. NOTE For further information, visit the NISSAN web site: www.nissan-europe.com. Select your country from the list and go to the “SERVICES” menu. If not available on the web site, contact a NISSAN dealer or qualified workshop.

4-16 Display screen, heater and air conditioner, and audio system 5 Starting and driving

Running-in schedule ...... 5-2 Electronic Stability Programme (ESP) OFF Before starting engine...... 5-2 switch...... 5-10 Precautions when starting and driving ...... 5-2 Parking...... 5-11 Exhaust gas (carbon monoxide) ...... 5-2 Trailer towing...... 5-12 Three-way catalyst (petrol engine model) ...... 5-3 Operating precautions ...... 5-12 Care when driving ...... 5-4 Tyre pressure ...... 5-12 Engine cold start period...... 5-4 Safety chains...... 5-13 Loading luggage...... 5-4 Trailer brakes...... 5-13 Driving in wet conditions...... 5-4 Trailer detection (where fitted) ...... 5-13 Driving in winter conditions ...... 5-4 Coupling device installation...... 5-13 Ignition switch...... 5-4 Electric power steering system ...... 5-14 Intelligent Key system (where fitted)...... 5-4 Brake system...... 5-15 Manual Transmission (MT) ...... 5-5 Brake precautions ...... 5-15 Steering lock ...... 5-6 Anti-lock Braking System (ABS)...... 5-15 Key positions...... 5-6 Vehicle security...... 5-16 Starting engine ...... 5-6 Cold weather driving...... 5-17 Petrol engine ...... 5-6 Battery ...... 5-17 Diesel engine...... 5-7 Engine coolant...... 5-17 NISSAN Anti-Theft System (NATS)...... 5-7 Tyre equipment...... 5-17 Driving vehicle ...... 5-8 Special winter equipment...... 5-17 Driving with Manual Transmission (MT) ...... 5-8 Corrosion protection...... 5-18 Electronic Stability Programme (ESP) (where fitted)...... 5-9 RUNNING-IN SCHEDULE BEFORE STARTING ENGINE PRECAUTIONS WHEN STARTING AND DRIVING

During the first 1,600 km (1,000 miles), follow these recommendations to obtain maximum engine per- WARNING WARNING formance and ensure the future reliability and The driving characteristics of your vehicle will • Never leave children or adults who would nor- economy of your new vehicle. Failure to follow these change remarkably by any additional load and its mally require the support of others alone in recommendations may result in shortened engine distribution, as well as by adding optional equip- your vehicle. Pets should not be left alone life and reduced engine performance. ment (trailer coupling, roof racks, etc.). Your driv- either. They could unknowingly activate • Do not drive at a constant speed, either fast or ing style and speed must be adjusted according switches or controls and inadvertently slow, for long periods of time. to the circumstances. Especially when carrying become involved in a serious accident and heavy loads, your speed must be reduced ad- injure themselves. On hot, sunny days, tem- • Do not run the engine over 4,000 rpm (HR16DE equately. peratures in a closed vehicle could quickly engine) or 2,500 rpm (K9K engine). become high enough to cause severe or pos- • Make sure the area around the vehicle is clear. Do not accelerate at full throttle in any gear. sibly fatal illness to people or animals. • Visually inspect tyres for their appearance and • Properly secure all luggage to help prevent it Do not start quickly. condition. Measure and check the tyre pressure • • from sliding or shifting. Do not place luggage for proper inflation. • Do not brake hard as much as possible. higher than the seatbacks. In a sudden stop • Do not tow a trailer for at least the first 800 km • Check that all windows and lights are clean. or collision, unsecured luggage could cause personal injury. (500 miles). • Adjust the seat and head restraint positions. • Adjust the inside and outside rearview mirror po- EXHAUST GAS (carbon monoxide) sitions. WARNING • Fasten your seat belt and ask all passengers to do the same. • Do not breathe exhaust gas; it contains co- lourless and odourless carbon monoxide. Car- • Check that all doors are closed. bon monoxide is dangerous. It can cause un- • Check the operation of the warning lights when consciousness or death. the ignition switch is turned to the ON position. • If you suspect that exhaust fumes are enter- • Maintenance items in the “8. Maintenance and ing the vehicle, drive with all windows fully do-it-yourself” section should be checked peri- open, and have the vehicle inspected imme- odically. diately. • Do not run the engine in closed spaces such as a garage.

5-2 Starting and driving • Do not park the vehicle with the engine run- – You have had an accident involving dam- three-way catalyst, causing it to overheat. Do ning for an extended period of time. age to the exhaust system, underbody, or not keep driving if the engine misfires, or if rear of the vehicle. noticeable loss of performance or other un- Keep the back door closed while driving, oth- • usual operating conditions are detected. Have erwise exhaust gas could be drawn into the THREE-WAY CATALYST (petrol engine the vehicle inspected promptly by a NISSAN passenger compartment. If you must drive model) dealer or qualified workshop. with the back door open, follow these precautions: WARNING • Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to – Open all the windows. • The exhaust gas and the exhaust system are misfire, damaging the three-way catalyst. – Turn the air recirculation mode off and set very hot. Keep people, animals and flammable Do not race the engine while warming it up. the fan speed control to the highest level materials away from the exhaust system com- • to circulate the air. ponents. • Do not push or tow your vehicle to start the engine. • If electrical wiring or other cable connections • Do not stop or park the vehicle over flam- must pass to a trailer through the seal of the mable materials such as dry grass, wastepa- back door or the body, follow the manufactur- per or rags. They may ignite and cause a fire. er’s recommendation to prevent carbon mon- NISSAN GREEN PROGRAM oxide entry into the vehicle. The three-way catalyst is an emission control device If a special body or other equipment is added • installed in the exhaust system. Exhaust gas in the for recreational or other usage, follow the three-way catalyst is burned at high temperatures to manufacturer’s recommendation to prevent help reduce pollutants. carbon monoxide entry into the vehicle. (Some recreational vehicle appliances such CAUTION as stoves, refrigerators, heaters, etc. may also • Do not use leaded petrol. (See “Recom- generate carbon monoxide.) mended fuel/lubricants and capacities” in the • The exhaust system and body should be in- “9. Technical information” section.) Deposits spected by a qualified mechanic whenever: from leaded petrol seriously reduce the ability of the three-way catalyst to help reduce – Your vehicle is raised while being serviced. exhaust pollutants and/or damage the three- – You suspect that exhaust fumes are enter- way catalyst. ing into the passenger compartment. • Keep your engine tuned up. Malfunctions in – You notice a change in the sound of the the ignition, fuel injection, or electrical sys- exhaust system. tems may cause overrich fuel to flow into the

Starting and driving 5-3 CARE WHEN DRIVING IGNITION SWITCH

Driving your vehicle to fit the circumstances is es- • Avoid sudden steering. sential for your safety and comfort. As a driver, you WARNING Avoid following too close to the vehicle in front. should be the one who knows best how to drive in • Never remove the key or turn the ignition switch the given circumstances. to the LOCK position while driving. The steering ENGINE COLD START PERIOD wheel will lock and could cause the driver to lose control of the vehicle. This could result in serious Due to the higher engine speeds, when the engine vehicle damage or personal injury. is cold, extra caution must be exercised when selecting a gear during the engine warm-up period after starting the engine. LOADING LUGGAGE Loads and their distribution and the attachment of equipment (coupling devices, roof luggage carriers, etc.) will considerably change the driving characteristics of the vehicle. Your driving style and speed must be adjusted according to the circumstances. NSD368 DRIVING IN WET CONDITIONS • Avoid accelerating or stopping suddenly. j1 LOCK (PUSH OFF) • Avoid sharp turning or lane changing suddenly. j2 LOCK (PUSH ON) • Avoid following too close to the vehicle in front. INTELLIGENT KEY SYSTEM When water covers the road surface with water (where fitted) puddles, small water streams, etc., reduce speed to The Intelligent Key system can operate the ignition prevent hydroplaning which can cause skidding and switch without taking the key out of your pocket or loss of control. Worn tyres will increase this risk. purse. The operating environment and/or conditions DRIVING IN WINTER CONDITIONS may affect the Intelligent Key system operation. • Drive cautiously. CAUTION • Avoid accelerating or stopping suddenly. • Be sure to carry the Intelligent Key with you when operating the vehicle. • Avoid sharp turning or lane changing suddenly.

5-4 Starting and driving • Never leave the Intelligent Key inside the ve- If the Intelligent Key is within the operating range, it MANUAL TRANSMISSION (MT) hicle when you leave the vehicle. is possible for anyone, even someone who does not carry the Intelligent Key, to turn the ignition switch to If the vehicle battery is discharged, the igni- • start the engine. tion switch cannot be moved from the LOCK position and if the steering lock is engaged, • The luggage area is not included in the operating the steering wheel cannot be moved. Charge range, but the Intelligent Key may function. the battery as soon as possible. (See “Jump If the Intelligent Key is placed on the instrument starting” in the “6. In case of emergency” sec- • panel, inside the glove box or door pocket, the tion.) Intelligent Key may not function. Remove the ignition switch cap jA when the me- If the Intelligent Key is placed near the door or chanical key is used. • SSD0392Z window outside the vehicle, the Intelligent Key Without Intelligent Key system may function.

SSD0436Z

SSD0645Z Operating range With Intelligent Key system The Intelligent Key functions can only be used for The ignition switch includes a device that helps pre- starting the engine when the Intelligent Key is within vent accidental removal of the key while driving. the specified operating range j1. The key can only be removed when the ignition When the Intelligent Key battery is almost switch is in the LOCK position. discharged or strong radio waves are present near The “OFF” position j1 is between the LOCK and the operating location, the Intelligent Key system’s ACC positions, although it is not marked on the igni- operating range becomes narrower and may not tion switch. function properly.

Starting and driving 5-5 STARTING ENGINE

Models with Intelligent Key system KEY POSITIONS PETROL ENGINE The ignition lock is designed so that the switch can LOCK (0) 1. Apply the parking brake. only be turned to the LOCK position when the PUSH 2. Depress the footbrake pedal. release button j2 has been pushed. The ignition key can only be removed at this position. 3. Move the shift lever to the N (Neutral) position, The Intelligent Key lock warning light blinks • and depress the clutch pedal to the floor while and the buzzer sounds when the ignition switch The steering lock can only be locked at this position. starting the engine. is not turned to the LOCK position completely Intelligent Key system: without pushing the PUSH release button j2. PUSH OFF - The steering lock can only be Intelligent Key system: Slowly “PUSH ON” the For further details regarding the functionality of locked at this position. ignition switch and depress the footbrake pedal. the Intelligent Key lock warning light, see “Intel- PUSH ON - The ignition switch will be unlocked When the Intelligent Key system warning light in ligent Key lock warning light (where fitted)” in the while carrying the Intelligent Key. the meter illuminates in green, the ignition switch “2. Instruments and controls” section. OFF (1) can be turned. When the mechanical key is being used, the ig- The Intelligent Key must be carried when op- • The engine is turned off with the steering wheel nition PUSH release button has to be pushed in erating the ignition switch. unlocked. order to turn the ignition switch to the LOCK When the Intelligent Key lock warning light in the position although the Intelligent Key lock warn- ACC (2) meter blinks in red and the inside warning buzzer ing light will not blink and the buzzer will The electrical accessory power activates without the emits a short beep, be sure that the shift lever is not sound. engine turned on. in the N (Neutral) position and the ignition switch is securely returned to the LOCK position. STEERING LOCK ON (3) To lock steering wheel 4. Crank the engine with your foot off the accelera- The ignition system and the electrical accessory tor pedal by turning the ignition switch to the 1. Turn the ignition switch to the LOCK position. power activate without the engine turned on. START position. 2. Remove the key, if it is inserted in the ignition START (4) 5. Immediately release the ignition switch when the switch. The engine starter activates and the engine will start. engine starts. If the engine starts, but fails to run, 3. Turn the steering wheel 1/6 of a turn clockwise The ignition switch, when released, will automati- repeat the above procedures. from the straight up position. cally turn to the ON position. If the engine is very hard to start in extremely cold To unlock steering wheel CAUTION or hot weather, depress the accelerator pedal and hold it to help start the engine. 1. Insert the key into the ignition switch. As soon as the engine has started, release the ignition switch immediately. 2. Gently turn the ignition switch while rotating the steering wheel slightly right and left.

5-6 Starting and driving CAUTION The Intelligent Key must be carried when op- 7. Allow the engine to idle for at least 30 seconds erating the ignition switch. after starting the engine to warm-up. Drive at Do not operate the starter for more than 15 • moderate speeds for a short distance first, espe- seconds at a time. If the engine does not start, When the Intelligent Key lock warning light in the cially in cold weather. turn the ignition switch off and wait 10 sec- meter blinks in red and the inside warning buzzer onds before cranking the engine again. Oth- emits a short beep, be sure that the shift lever is CAUTION erwise, the starter could be damaged. in the N (Neutral) position and the ignition switch Do not leave the vehicle unattended while the is securely returned to the LOCK position. • If it becomes necessary to start the engine engine is warming up. with a booster battery and jumper cables, the 4. Turn the ignition switch to the ON position and instructions and cautions contained in the “6. wait until the glow plug indicator light turns NISSAN ANTI-THEFT SYSTEM (NATS) In case of emergency” section should be care- off. The NISSAN Anti-Theft System (NATS) will not al- fully followed. low the engine to start without the use of the regis- 5. Crank the engine with your foot off the accelera- tered NATS key, integrated keyfob or Intelligent Key. 6. Allow the engine to idle for at least 30 seconds tor pedal by turning the ignition switch to the after starting the engine to warm-up. Drive at START position. If the engine does not start using the registered key, moderate speeds for a short distance first, espe- it may be due to interference caused by: 6. Immediately release the ignition switch when the cially in cold weather. engine starts. If the engine starts, but fails to run, • Another NATS key, integrated keyfob or Intelli- CAUTION repeat the above procedures. gent Key. Do not leave the vehicle unattended while the CAUTION • Automated toll road device. engine is warming up. • Do not operate the starter for more than 20 • Automated payment device. DIESEL ENGINE seconds at a time. If the engine does not start, turn the ignition switch off and wait 20 sec- • Other devices that transmit similar signals. 1. Apply the parking brake. onds before cranking the engine again. Oth- Start the engine using the following procedure: 2. Depress the footbrake pedal. erwise, the starter could be damaged. 1. Remove any items that may be causing the inter- 3. Move the shift lever to the N (Neutral) position, • If it becomes necessary to start the engine ference away from the key. and depress the clutch pedal to the floor while with a booster battery and jumper cables, the 2. Leave the ignition switch in the ON position for instructions and cautions contained in the “6. starting the engine. approximately 5 seconds. In case of emergency” section should be care- Intelligent Key system: Slowly “PUSH ON” the fully followed. 3. Turn the ignition switch to the “OFF” or LOCK ignition switch and depress the footbrake pedal. position, and wait approximately 5 seconds. When the Intelligent Key system warning light in the meter illuminates in green, the ignition switch 4. Start the engine. can be turned.

Starting and driving 5-7 DRIVING VEHICLE

5. Repeat the steps above until all possible interfer- DRIVING WITH MANUAL ences are eliminated. TRANSMISSION (MT) If this procedure allows the engine to start, NISSAN recommends placing the registered key separate WARNING from other devices to avoid interference. • Do not downshift abruptly on slippery roads. This may cause a loss of control. • Do not over-rev the engine when shifting to a lower gear. This may cause a loss of vehicle

control or engine damage. SSD0535Z CAUTION • Do not rest your foot on the clutch pedal while Shifting gear driving. This may damage the clutch system. To change gears, or when upshifting or downshift- • Fully depress the clutch pedal before shifting ing, fully depress the clutch pedal, shift into the ap- to help prevent transmission damage. propriate gear, then slowly and smoothly release the clutch pedal. • Stop the vehicle completely before shifting into the R (Reverse) position. Start the vehicle in the “1” (1st) position and shift to the “2” (2nd), “3” (3rd), “4” (4th) and “5” (5th) gear When the vehicle is stopped for a period of • in sequence according to the vehicle speed. time, for example waiting at stoplights, shift to the N (Neutral) position and release the If it is difficult to move the shift lever into the R clutch pedal with the footbrake pedal (Reverse) or “1” (1st) position, shift to the N (Neu- depressed. tral) position, and then release the clutch pedal once. Fully depress the clutch pedal again and shift into R Starting vehicle or “1”. 1. After starting the engine, depress the clutch You cannot shift directly from the “5” (5th) position pedal to the floor and move the shift lever to the into the R (Reverse) position. First shift into the N “1” (1st) or R (Reverse) position. (Neutral) position, then shift into the R (Reverse) 2. Slowly depress the accelerator pedal, releasing position. the clutch pedal and parking brake at the same time.

5-8 Starting and driving ELECTRONIC STABILITY PROGRAMME (ESP) (where fitted)

Suggested maximum speed in each gear WARNING Downshift to a lower gear if the engine is not run- The Electronic Stability Programme (ESP) sys- ning smoothly, or if you need to accelerate. • tem is designed to help improve driving sta- Do not exceed the maximum suggested speed bility but does not prevent accidents due to (shown below) in any gear. For level road driving, abrupt steering operation at high speeds or use the highest gear suggested for that speed. Al- due to careless or dangerous driving tech- ways observe posted speed limits, and drive ac- niques. Reduce vehicle speed and be espe- cording to the road conditions which will ensure cially careful when driving and cornering on safe operation. Do not over-rev the engine when slippery surfaces and always drive carefully. SSD0879Z shifting to a lower gear as it may cause engine dam- If engine related parts such as a muffler are age or loss of vehicle control. • not standard equipment or are extremely de- Upshift indicator HR16DE engine model: teriorated, the ESP OFF indicator or “SLIP” The manual transmission upshift indicator is located km/h (MPH) indicator or both indicator lights may illumi- in the tachometer and shows the driver the timing to 1st 43 (27) nate. shift into a higher gear by illuminating. The use of the 2nd 79 (49) • Do not modify the vehicle’s suspension. If upshift indicator will help you to upshift at a constant 3rd 117 (73) suspension parts such as shock absorbers, engine speed from any gear. 4th 148 (92) struts, springs, stabiliser bars and bushings The upshift indicator will illuminate when the engine 5th — (—) are not NISSAN-approved or are extremely deteriorated the ESP system may not operate speed reaches the set figure while driving. K9K engine model: properly. This could adversely affect vehicle The engine speed for upshifting can be set in the km/h (MPH) handling performance, and the ESP OFF indi- setting mode of the vehicle information display. See 1st 32 (20) cator or “SLIP” indicator or both indicator “Vehicle information display” in the “2. Instruments 2nd 59 (37) lights may illuminate. and controls” section. 3rd 91 (57) 4th 124 (77) • If brake related parts such as brake pads, ro- There may be a slight difference between the tors and callipers are not standard equipment 5th — (—) timing of the upshift indicator illumination and or are extremely deteriorated, the ESP OFF the tachometer indication. indicator or “SLIP” indicator or both indicator lights may illuminate. • When driving on extremely inclined surfaces such as higher banked corners, the ESP system may not operate properly and the ESP

Starting and driving 5-9 OFF indicator or “SLIP” indicator or both indi- • Indicator light ELECTRONIC STABILITY cator lights may illuminate. Do not drive on If a malfunction occurs in the system, the “SLIP” PROGRAMME (ESP) OFF SWITCH these types of roads. and ESP OFF indicator lights illumi- • When driving on unstable surfaces such as a nate in the instrument panel. As long as these turntable, ferry, elevator or ramp, the ESP OFF indicators are illuminated, the ESP system func- indicator or “SLIP” indicator or both indicator tion is cancelled. lights may illuminate. This is not a malfunc- The ESP system uses a Brake Limited Slip Differen- tion. Restart the engine after driving onto a tial (BLSD) function to improve vehicle traction. The stable surface. BLSD system works when one of the driving wheels • If wheels or tyres other than those recom- is spinning on a slippery surface. The BLSD system mended are used, the ESP system may not brakes the spinning wheel, which distributes the operate properly and ESP OFF indicator or driving power to the other drive wheel. If the vehicle SIC2257Z “SLIP” indicator or both indicator lights may is operated with the ESP system turned off, all ESP illuminate. system functions will be turned off. The vehicle should be driven with the Electronic • The ESP system is not a substitute for winter The BLSD system and ABS will still operate with the Stability Programme (ESP) system on for most driv- tyres or tyre chains on a snow-covered road. ESP system off. If the BLSD system is activated, the ing conditions. “SLIP” indicator light will blink and you may hear a When accelerating or driving on slippery surfaces, When the vehicle is stuck in mud or snow, the ESP clunk noise and/or feel a pulsation in the brake pedal. the tyres may spin or slide. With the Electronic Sta- system reduces the engine output to reduce wheel This is normal and is not an indication of a malfunc- bility Programme (ESP) system, sensors detect spin. The engine speed will be reduced even if the tion. these movements and control the braking and en- accelerator is depressed to the floor. If maximum gine output to help improve vehicle stability. While the ESP system is operating, you may feel a engine power is needed to free a stuck vehicle, turn pulsation in the brake pedal and hear a noise or feel the ESP system off. When the ESP system is operating, the “SLIP” • a vibration from under the bonnet. This is normal indicator in the instrument panel blinks. To turn off the ESP system, push the ESP OFF and indicates that the ESP system is working prop- switch located on the lower side of the instrument If the “SLIP” indicator blinks, the road conditions erly. • panel. The indicator light will illuminate. are slippery. Be sure to adjust your speed and The ESP system computer has a built-in diagnostic driving to these conditions. Be sure to drive care- Push the ESP OFF switch again or restart the en- feature that tests the system each time you start the fully. (See “Slip indicator light (where fitted)” in gine to turn on the system. engine and move the vehicle at a low speed forward the “2. Instruments and controls” section and or backward. When the self-test occurs, you may “Electronic Stability Programme (ESP) off indi- hear a “clunk” noise and/or feel a pulsation in the cator light (where fitted)” in the “2. Instruments footbrake pedal. This is normal and is not an indica- and controls” section.) tion of a malfunction.

5-10 Starting and driving PARKING

WARNING • Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. • Safe parking procedures require that both the parking brake be applied and the shift lever placed in an appropriate gear. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in an accident. SSD0488Z • Never leave the engine running while the ve- Left-Hand Drive (LHD) model hicle is unattended. • Never leave children or adults who would normally require the support of others alone in the vehicle. Pets should not be left alone either. They could unknowingly activate switches or controls and inadvertently become involved in a serious accident and injure themselves. On hot, sunny days, temperatures in a closed vehicle could quickly

become high enough to cause severe or pos- SSD0489Z sibly fatal illness to people and animals. Right-Hand Drive (RHD) model HEADED DOWNHILL WITH CURB j1 1. Firmly apply the parking brake. Turn the wheels towards the curb and move the 2. Move the shift lever to the R (Reverse) position. vehicle forward until the curb side wheel gently When parking on an uphill grade, move the shift touches the curb. Then apply the parking brake. lever to the “1” (1st) position. HEADED UPHILL WITH CURB j2 3. To help prevent the vehicle from moving into traffic when parked on an incline, it is a good prac- Turn the wheels away from the curb and allow tice to turn the wheels as illustrated. the vehicle to move back until the curb side wheel gently touches the curb. Then apply the parking brake.

Starting and driving 5-11 TRAILER TOWING

HEADED UPHILL OR DOWNHILL, WITHOUT Your new vehicle was designed to be used primarily NISSAN dealer or qualified workshop where you CURB j3 to carry passengers and luggage. can also obtain more detailed information about trailer towing. Turn the wheels toward the side of the road so Towing a trailer will place additional loads on your the vehicle will move away from the centre of the vehicle’s engine, drive train, steering, braking and • Never allow the total trailer load (trailer weight road if the vehicle moves. Then apply the parking other systems. The towing of a trailer will exagger- plus its cargo weight) to exceed the maximum brake. ate other conditions such as sway caused by cross- set for the vehicle and the coupling device. See winds, rough road surfaces or passing trucks. a NISSAN dealer or qualified workshop for more 4. Turn the ignition switch to the LOCK position information. and remove the key (if inserted). Your driving style and speed must be adjusted according to the circumstances. Before towing a • The trailer must be loaded so that heavy goods trailer, see a NISSAN dealer or qualified workshop are placed over the axle. The maximum allowable for an explanation about the proper use of towing vertical load on the trailer hitch must not be ex- equipment. ceeded. OPERATING PRECAUTIONS • Have your vehicle serviced more often than at the intervals specified in a separate maintenance • Avoid towing a trailer during the running-in pe- booklet. riod. • Trailer towing requires more fuel than under nor- • Before driving, make sure that the lighting sys- mal circumstances because of a considerable tem of the trailer works properly. increase in traction power and resistance. • Observe the legal maximum speeds for trailer While towing a trailer, check the engine coolant operation. temperature indicator to prevent the vehicle from Do not exceed 100 km/h (62 MPH). overheating. • Avoid abrupt starts, accelerations and stops. TYRE PRESSURE • Avoid sharp turns and lane changes. When towing a trailer, inflate the vehicle tyres to the maximum recommended COLD tyre pressure (for Always drive your vehicle at a moderate speed. • full loading) indicated on the tyre placard. Follow the trailer manufacturer’s instructions. • Do not tow a trailer when the vehicle is installed with • Choose proper coupling devices (trailer hitch, a temporary spare tyre or a compact spare tyre. safety chain, roof carrier, etc.) for your vehicle and trailer. These devices are available from a

5-12 Starting and driving SAFETY CHAINS Always use a suitable chain between the vehicle and trailer. The chain should be crossed and should be attached to the hitch, not to the vehicle bumper or axle. Be sure to leave enough slack in the chain to permit turning corners. TRAILER BRAKES Ensure that trailer brakes are installed as required by local regulations. Also check that all other trailer equipment conforms to local regulations. Always block the wheels on both the vehicle and trailer when parking. Apply the hand brake on the trailer where fitted. Parking on a steep slope is not recommended. If parking on a steep slope is unavoidable, place the shift lever in an appropriate gear, and turn the front wheels towards the curb. TRAILER DETECTION (where fitted) When towing a trailer with a Genuine NISSAN C2 tow bar electrical kit and the turn signal switch is SSD0882 used, the electrical system of the vehicle will detect the additional electrical load of the trailer lighting. As a result, there will be an additional turn indicator in COUPLING DEVICE INSTALLATION • The coupling device, mounting points and instal- the meter dedicated to the trailer. lation parts on your vehicle: as shown as an ex- NISSAN recommends that the coupling device for ample in the illustration. trailer towing be installed under the following conditions: • Rear overhang of coupling device: jA 956 mm (37.6 in) • Maximum permissible vertical load on the coupling device: 736 N (75 kg, 165 lb) Follow all of the coupling device manufacturer’s instructions for installation and use.

Starting and driving 5-13 ELECTRIC POWER STEERING SYSTEM

When removing the spare tyre from the vehicle with properly and may need servicing. Have the electric the trailer coupling device installed, it is necessary WARNING power steering system checked by a NISSAN dealer to unload the vehicle. (See “Flat tyre” in the “6. In If the engine is not running or is turned off while or qualified workshop. (See “Electric power steer- case of emergency” section for spare tyre removal.) driving, the power assist for the steering will not ing warning light” in the “2. Instruments and work. The steering will be much harder to oper- controls” section.) ate. When the electric power steering warning light illu- When the electric power steering warning light minates with the engine running, the power assist illuminates with the engine running, the power for the steering will cease operation. You will still assist for the steering will cease operation. You have control of the vehicle. However, greater steer- will still have control of the vehicle but the steering effort is needed, especially in sharp turns and at ing will be harder to operate. low speeds. The electric power steering system is designed to provide power assist while driving to operate the steering wheel with light force. When the steering wheel is operated repeatedly or continuously while parking or driving at a very low speed, the power assist for the steering wheel will be reduced. This is to prevent overheating of the electric power steering system and protect it from getting damaged. While the power assist is reduced, steering wheel operation will become heavy. When the temperature of the electric power steering system goes down, the power assist level will return to normal. Avoid repeating such steering wheel operations that could cause the electric power steering system to overheat. You may hear a fricative sound when the steering wheel is operated quickly. However, this is not a malfunction. If the electric power steering warning light illuminates while the engine is running, it may indicate the electric power steering system is not functioning

5-14 Starting and driving BRAKE SYSTEM

The brake system has two separate hydraulic cir- braking, accelerating or downshifting. Abrupt brak- ANTI-LOCK BRAKING SYSTEM (ABS) cuits. If one circuit malfunctions, you will still have ing or acceleration could cause the wheels to skid braking ability at two wheels. andresultinanaccident. WARNING BRAKE PRECAUTIONS Wet brakes • The Anti-lock Braking System (ABS) is a so- Vacuum assisted brakes When the vehicle is washed or driven through wa- phisticated device, but it cannot prevent acci- ter, the brakes may get wet. As a result, your brak- dents resulting from careless or dangerous The brake booster aids braking by using engine ing distance will be longer and the vehicle may pull driving techniques. It can help maintain ve- vacuum. If the engine stops, you can stop the ve- to one side during braking. hicle control during braking on slippery sur- hicle by depressing the footbrake pedal. However, faces. Remember that stopping distances on greater foot pressure on the footbrake pedal will be To dry the brakes, drive the vehicle at a safe speed slippery surfaces will be longer than on nor- required to stop the vehicle. The stopping distance while lightly depressing the brake pedal to heat up mal surfaces even with ABS. Stopping dis- will be longer. the brakes. Do this until the brakes return to normal. tances may also be longer on rough, gravel or Avoid driving the vehicle at high speeds until the snow covered roads, or if you are using tyre If the engine is not running or is turned off while driv- brakes function correctly. ing, the power assisted brakes will not function. chains. Always maintain a safe distance from Braking will be harder. Driving uphill the vehicle in front of you. Ultimately, the driver is responsible for safety. When starting on a steep grade, it is sometimes dif- WARNING ficult to operate both the brake and clutch (for MT • Tyre type and condition may also affect braking effectiveness. Do not coast with the engine stopped. model). Apply the parking brake to hold the vehicle. Do not slip the clutch. When ready to start, slowly • When replacing tyres, install the specified Using brakes release the parking brake while depressing the ac- size of tyres on all four wheels. celerator pedal and releasing the clutch pedal. Avoid resting your foot on the footbrake pedal while • When installing a spare tyre, make sure driving. This will overheat the brakes, wear out the Driving downhill that it is the proper size and type as speci- brake linings/pads faster, and increase fuel con- fied on the tyre placard. (See “Tyre The engine braking action is effective for controlling sumption. placard” in the “9. Technical information” the vehicle while descending hills. The shift lever section.) To help reduce brake wear and to prevent the brakes should be placed in the lower speed position prior from overheating, reduce speed and downshift to a to descending. • For detailed information, see “Tyres and lower gear before going down a slope or long grade. wheels” in the “8. Maintenance and Overheated brakes may reduce braking perfor- do-it-yourself” section. mance and could result in loss of vehicle control. The Anti-lock Braking System (ABS) controls the While driving on a slippery surface, be careful when brakes so the wheels do not lock during hard braking or when braking on slippery surfaces. The sys-

Starting and driving 5-15 VEHICLE SECURITY

tem detects the rotation speed at each wheel and test or while driving, have the vehicle checked by a When leaving your vehicle unoccupied: varies the brake fluid pressure to prevent each wheel NISSAN dealer or qualified workshop. Always take the key with you - even when leav- from locking and sliding. By preventing each wheel • ing the vehicle in your own garage. from locking, the system helps the driver maintain Normal operation steering control and helps to minimise swerving and The ABS operates at speeds above 5 to 10 km/h (3 • Close all windows completely and lock all doors. spinning on slippery surfaces. to 6 MPH). The speed varies according to road con- • Always park your vehicle where it can be seen. Using system ditions. Park in a well lit area during the night. When the ABS senses that one or more wheels are Depress the brake pedal and hold it down. Depress If the security system is equipped, use it - even close to locking up, the actuator rapidly applies and • the brake pedal with firm steady pressure, but do for a short period. releases hydraulic pressure. This action is similar to not pump the brakes. The ABS will operate to pre- pumping the brakes very quickly. You may feel a Never leave children or pets in the vehicle unat- vent the wheels from locking up. Steer the vehicle to • pulsation in the brake pedal and hear a noise from tended. avoid obstacles. under the bonnet or feel a vibration from the actua- • Never leave valuables inside the vehicle. Always tor when it is operating. This is normal and indicates take valuables with you. WARNING that the ABS is operating properly. However, the Do not pump the brake pedal. Doing so may re- pulsation may indicate that road conditions are haz- • Never leave the vehicle documents in the ve- sult in increased stopping distances. ardous and extra care is required while driving. hicle. Self-test feature • Never leave articles on a roof rack. Remove them from the rack and keep and lock them in a safe The ABS includes electronic sensors, electric place such as inside the boot. pumps, hydraulic solenoids and a computer. The Never leave the spare key in the vehicle. computer has a built-in diagnostic feature that tests • the system each time you start the engine and move the vehicle at a low speed in forward or reverse. When the self-test occurs, you may hear a “clunk” noise and/or feel a pulsation in the brake pedal. This is normal and does not indicate a malfunction. If the computer senses a malfunction, it switches the ABS off and illuminates the ABS warning light on the instrument panel. The brake system then operates normally, but without anti-lock assistance. If the ABS warning light illuminates during the self-

5-16 Starting and driving COLD WEATHER DRIVING

ciency, the battery should be checked regularly. For facturer to ensure a tight fit. Loose end links of WARNING details, see “Battery” in the “8. Maintenance and the tyre chains must be secured or removed to • Whatever the condition, drive with caution. do-it-yourself” section of this manual. prevent the possibility of whipping action damage to the fenders or underbody. In addition, Accelerate and decelerate with great care. If ENGINE COOLANT accelerating or decelerating too fast, the drive drive at a reduced speed, otherwise, your ve- wheels will lose even more traction. If the vehicle is to be left outside without anti-freeze, hicle may be damaged and/or vehicle handling drain the cooling system, including the engine block. and performance may be adversely affected. Allow more stopping distance in cold weather • Refill before operating the vehicle. For details, see driving. Braking should be started sooner than “Changing engine coolant” in the “8. Maintenance SPECIAL WINTER EQUIPMENT on dry pavement. and do-it-yourself” section of this manual. It is recommended that the following items be car- • Keep at a greater distance from the vehicle in ried in the vehicle during the winter: front of you on slippery roads. TYRE EQUIPMENT A scraper and stiff-bristled brush to remove ice 1. If you have snow tyres installed on the front/rear • Wet ice (0°C, 32°F and freezing rain), very cold and snow from the windows. • wheels of your vehicle, they should be of the snow and ice can be slick and very difficult to same size, loading range, construction and type A sturdy, flat board to be placed under the jack drive on. The vehicle will have a lot less trac- • (bias, bias-belted or radial) as the rear/front tyres. to give it firm support. tion or grip under these conditions. Try to avoid driving on wet ice until the road is salted 2. If the vehicle is to be operated in severe winter • A shovel to dig the vehicle out of snowdrifts. or sanded. conditions, snow tyres should be installed on all Engine block heater (where fitted) four wheels. • Watch for slippery spots (glaring ice). These may appear on an otherwise clear road in 3. For additional traction on icy roads, studded tyres WARNING shaded areas. If a patch of ice is seen ahead, may be used. However, some countries, prov- brake before reaching it. Try not to brake while inces and states prohibit their use. Check local, Do not use the heater with an ungrounded elec- actually on the ice, and avoid any sudden state and provincial laws before installing stud- trical system or two-pronged (cheater) adapters. steering manoeuvres. ded tyres. You can be injured by an electrical shock if you use an ungrounded connection. • Snow can trap dangerous exhaust gas under Skid and traction capabilities of studded snow your vehicle. Keep snow clear of the exhaust tyres, on wet or dry surfaces, may be poorer An engine block heater to assist in extreme cold pipe and from around your vehicle. than that of non-studded snow tyres. temperature starting is available through a NISSAN dealer or qualified workshop. BATTERY 4. Snow chains may be used if desired. Make sure they are the proper size for the tyres on your If the battery is not fully charged during extremely vehicle and are installed according to the chain cold weather conditions, the battery fluid may freeze manufacturer’s instructions. Use chain tension- and damage the battery. To maintain maximum effi- ers when recommended by the tyre chain manu-

Starting and driving 5-17 CORROSION PROTECTION Chemicals used for road surface deicing are extremely corrosive and will accelerate corrosion and the deterioration of underbody components such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders. In the winter, the underbody must be cleaned periodically. For additional information, see “Cor- rosion protection” in the “7. Appearance and care” section of this manual. For additional protection against rust and corrosion, which may be required in some areas, consult a NISSAN dealer or qualified workshop.

5-18 Starting and driving 6 In case of emergency

Flat tyre ...... 6-2 Jump starting ...... 6-6 Stopping vehicle...... 6-2 Push starting ...... 6-7 Preparing tools and spare tyre ...... 6-2 If your vehicle overheats...... 6-7 Blocking wheels ...... 6-3 Towing your vehicle ...... 6-8 Removing tyre...... 6-3 Towing precautions ...... 6-8 Installing spare tyre...... 6-5 Towing recommended by NISSAN ...... 6-8 Stowing damaged tyre and tools...... 6-5 FLAT TYRE

If you have a flat tyre, follow the instructions as fol- PREPARING TOOLS AND SPARE lows. TYRE STOPPING VEHICLE

WARNING • Be sure to apply the parking brake firmly. • Be sure to move the shift lever to the R (Re- verse) position. • Never change tyres when the vehicle is on a slope, ice or slippery area. This is hazardous. SCE0838Z • Never change tyres when the oncoming traffic is close to your vehicle. Call for professional road assistance. Remove the jack, necessary tools and the spare tyre from the storage area. 1. Safely move the vehicle off the road away from traffic. The jack and jacking tools are located under the front passenger’s seat. 2. Turn on the hazard indicator flasher lights. 3. Park on a level surface. 4. Apply the parking brake.

5. Move the shift lever to the R (Reverse) position. SCE0839 6. Turn off the engine. 7. Open the bonnet: The spare tyre is located under the rear of the vehicle. To warn other traffic. • When the trailer coupling device is installed in the • To signal professional road assistance per- vehicle, unload the vehicle before removing the sonnel that you need assistance. spare tyre. (See “Trailer towing” in the “5. Starting 8. Have all passengers get out from the vehicle and and driving” section for more information about the stand in a safe place, away from other traffic and trailer coupling device.) clear of the vehicle.

6-2 In case of emergency To remove the spare tyre, perform the following pro- BLOCKING WHEELS REMOVING TYRE cedures. Spare tyre 1. Open the back door. 2. Loosen the bolt j1 anticlockwise approximately 40 turns using the wheel nut wrench to lower the spare tyre. 3. Stop turning the bolt when the tyre is lowered to the place where the tyre basket j2 can be removed from the hook j3. MCE0001DZ SCE0630Z Do not loosen the bolt excessively, otherwise the basket may fall suddenly. WARNING Removing wheel cover (where fitted) 4. Hold the tyre basket and remove it from the hook Be sure to block the appropriate wheel to pre- WARNING by pushing the basket upward. vent the vehicle from moving, which may cause 5. Lower the tyre basket slowly to the ground, and personal injury. Never use your hands to remove the wheel cover. This may cause personal injury. then take out the spare tyre. Place suitable blocks j1 at both the front and back j j Spare tyre basket bolt tightening torque: of the wheel diagonally opposite the flat tyre Ato To remove the wheel cover, use the jack rod 1as prevent the vehicle from moving when it is jacked illustrated. 24.5 to 29.4 N•m (2.5 to 2.9 kg-m, 18 to 21 ft-lb) up. Apply cloth j2 between the wheel and jack rod to prevent damaging the wheel and wheel cover.

In case of emergency 6-3 SCE0637Z SCE0574Z

Removing wheel centre cap Jacking up vehicle • Never start or run the engine while the vehicle (where fitted) is on the jack. The vehicle may move sud- WARNING denly, and this may cause an accident. To remove the wheel centre cap, turn it anticlockwise as illustrated. • Be sure to read and follow the instructions in • Never allow passengers to remain in the ve- this section. hicle while the tyre is off the ground. • Do not get under a vehicle that is supported • Be sure to read the caution label attached to only by a jack: Use vehicle support stands. the jack body before using. • Never use a jack which is not provided with 1. Place the jack directly under the jack-up point as your vehicle. illustrated so that the top of the jack contacts the vehicle at the jack-up point. • The jack, which is provided with your vehicle, is designed only to lift your vehicle during a The jack should be placed on firm level tyre change. Do not use the jack provided with ground. SCE0842Z your vehicle on other vehicles. 2. Align the jack head between the two notches Jack-up points • Never jack up the vehicle at a location other located at the jack-up point of either the front or than the jack-up point that is specified. the rear section. • Never lift the vehicle more than necessary. 3. Fit the groove of the jack head between the notches as shown. • Never use blocks on or under the jack. 4. Loosen each wheel nut, anticlockwise, one or two turns with the wheel nut wrench.

6-4 In case of emergency Do not remove the wheel nuts until the tyre is properly tightened wheel nuts may cause the off the ground. wheel to become loose or come off. This WARNING could cause an accident. 5. Carefully raise the vehicle until the clearance be- Retighten the wheel nuts when the vehicle has tween the tyre and ground is achieved. • Never use oil or grease on the wheel studs or been driven for 1,000 km (600 miles) (also in nuts. This may cause the wheel nuts to be- cases of a flat tyre, etc.). 6. To lift the vehicle, securely hold the jack lever come loose. and rod with both hands and turn the jack lever. STOWING DAMAGED TYRE AND 1. Clean any mud or dirt from the surface between TOOLS Removing tyre the wheel and hub. 1. Remove the wheel nuts. 2. Carefully put the spare tyre on and tighten the WARNING 2. Remove the damaged tyre. wheel nuts with your fingers. Check that all the Be sure that the tyre, jack and tools used are wheel nuts contact the wheel surface horizon- properly stored after use. Such items can be- CAUTION tally. come dangerous projectiles in an accident or The tyre is heavy. Be sure that your feet are clear 3. Tighten the wheel nuts alternately and evenly in sudden stop. from the tyre and use gloves as necessary to the sequence illustrated (j1-j4 ), more than 2 avoid injury. 1. Securely store the damaged tyre, jack and tools times with the wheel nut wrench, until they are used in the storage area in the reverse order of INSTALLING SPARE TYRE tight. removal. (See “Preparing tools and spare tyre” 4. Lower the vehicle slowly until the tyre touches earlier in this section.) the ground. 2. Close the back door. 5. Tighten the wheel nuts securely, with the wheel nut wrench, in the sequence illustrated. 6. Lower the vehicle completely. Tighten the wheel nuts to the specified torque with a torque wrench as soon as possible. Wheel nut tightening torque: SCE0576Z 108 N•m (11 kg-m, 80 ft-lb) The wheel nuts must be kept tightened to speci- WARNING fication at all times. It is recommended that the wheel nuts be tightened to specification at each Never use wheel nuts which are not provided • lubrication interval. with your vehicle. Incorrect wheel nuts or im-

In case of emergency 6-5 JUMP STARTING

wheel cannot be moved. Connect the jumper WARNING cables to the booster vehicle jB before turning • Incorrect jump starting can lead to a battery the ignition switch and disengaging the steering explosion. The battery explosion may result in lock. severe injury or death. It may also result in 2. Apply the parking brake. damage to the vehicle. Be sure to follow the instructions in this section. 3. Move the shift lever to the N (Neutral) position. • Explosive hydrogen gas is always present in 4. Switch off all unnecessary electrical systems the vicinity of the battery. Keep all sparks and (headlights, heater, air conditioner, etc.). flames away from the battery. SCE0840Z 5. Turn the ignition switch to the LOCK position. HR16DE engine model • Always wear suitable eye protection and re- 6. Remove the vent caps, where fitted, on the bat- move rings, bracelets, and any other jewellery tery. whenever working on or near a battery. 7. Cover the battery with a firmly wrung out moist • Never lean over the battery while jump start- cloth to reduce the hazard of an explosion. ing. 8. Connect the jumper cables in the sequence as • Never allow battery fluid to come into contact illustrated (j1,j2,j3,j4). with eyes, skin, clothes or the vehicle’s painted surfaces. Battery fluid is a corrosive CAUTION sulphuric acid which can cause severe burns. • Always connect positive j+ to positive j+ and If the fluid comes into contact with anything, negative j- to body ground, NOT to the bat- SCE0848Z immediately flush the contacted area with tery’s negative j-. plenty of water. K9K engine model • Be sure that the jumper cables do not touch Keep the battery out of the reach of children. • 1. If the booster battery is in another vehicle jB, moving parts in the engine compartment. • The booster battery must be rated at 12 volts. position the two vehicles jA and jB to bring the • Be sure that the jumper cable’s clamps do Use of an incorrectly rated battery will dam- batteries into close proximity to each other. not contact any other metal. age your vehicle. CAUTION 9. Start the engine of the booster vehicle jB and let Never attempt to jump start a frozen battery. • If the battery of vehicle jA equipped with the it run for a few minutes. It could explode and cause serious injury. Intelligent Key system is discharged, the ignition 10. Depress the accelerator pedal of the booster switch cannot be moved from the LOCK position vehicle jB at about 2,000 rpm. and, if the steering lock is engaged, the steering

6-6 In case of emergency PUSH STARTING IF YOUR VEHICLE OVERHEATS

11. Start the engine of the jumped vehicle jAinthe Do not attempt to start the engine by pushing the normal manner. vehicle. WARNING CAUTION CAUTION • Never continue driving if your vehicle overheats. Doing so could cause a vehicle fire. Never keep the starter motor engaged for more • Catalyst equipped model should not be than 10 seconds. If the engine does not start started by pushing. Attempting to do so may • Never open the bonnet if steam is coming right away, turn the ignition switch “OFF” and cause damage to the catalyst. out. wait at least 10 seconds before trying again. • Never try to start the engine by towing. When • Never remove the radiator or coolant reser- 12. After the engine is started, carefully disconnect the engine starts, the forward surge could voir cap while the engine is hot. If the radiator the jumper cables in the opposite sequence cause the vehicle to collide with the towing or coolant reservoir cap is removed when the from that illustrated (j4,j3,j2,j1). vehicle. engine is hot, pressurised hot water will spurt out and possibly cause burning, scalding or 13. Remove and dispose of the cloth as it may be serious injury. contaminated with corrosive acid. • If steam or coolant is coming from the engine, 14. Replace the vent caps, if removed. stand clear of the vehicle to prevent getting burned. • The engine cooling fan can start at any time when the coolant temperature exceeds preset degrees. • Be careful not to allow your hands, hair, jewellery or clothing to come into contact with, or to get caught in the cooling fan or drive belts. If your vehicle is overheating (indicated by the high temperature indicator), or if you feel a lack of engine power, detect unusual noise, etc., take the following steps: 1. Safely move the vehicle off the road away from traffic. 2. Turn on the hazard indicator flasher lights. 3. Apply the parking brake.

In case of emergency 6-7 TOWING YOUR VEHICLE

4. Move the shift lever to the N (Neutral) position. Have your vehicle inspected/repaired at a NISSAN When towing your vehicle, local regulations for tow- dealer or qualified workshop. ing must be followed. Incorrect towing equipment DO NOT STOP THE ENGINE. could damage your vehicle. To assure proper tow- 5. Open all the windows. ing and to prevent accidental damage to your vehicle, NISSAN recommends that you have profes- 6. Turn off the air conditioner (where fitted). Move sional road assistance personnel tow your vehicle. It the temperature control to maximum hot and the is advisable to have the professional road assistant fan control to high speed. carefully read the following precautions. 7. Get out from the vehicle. TOWING PRECAUTIONS 8. Visually inspect and listen for steam or coolant escaping from the radiator before opening the • Be sure that the transmission, steering system, bonnet. Wait until no steam or coolant can be and drivetrain are in working condition before seen before proceeding. towing. If any units are damaged, the vehicle must be towed using a dolly or flatbed tow truck. 9. Open the engine bonnet. • NISSAN recommends that your vehicle be towed 10. Visually inspect if the cooling fan is running. with the driving (front) wheels off the ground. 11. Visually inspect the radiator and radiator hoses • Always attach safety chains before towing. for leakage. TOWING RECOMMENDED BY If the cooling fan is not running or the coolant is NISSAN leaking, stop the engine. 12. After the engine cools down, check the coolant level in the reservoir with the engine running. Do not open the radiator cap (if equipped). 13. Add coolant to the reservoir if necessary.

WARNING Before removing the engine coolant reservoir cap and to avoid the danger of being scalded, cover the reservoir cap with a rag and loosen the res- SCE0843Z ervoir cap to the first notch to allow the steam to escape.

6-8 In case of emergency Towing the vehicle CAUTION Front wheels on the ground: • Never tow a manual transmission model backward with all four wheels on the ground. NISSAN recommends that towing dollies be used under the front wheels when towing your vehicle or 1. Turn the ignition switch to the “OFF” position. the vehicle be placed on a flatbed tow truck as illus- 2. Move the shift lever to the N (Neutral) position. trated. 3. Release the parking brake. Manual Transmission (MT) model: If you have to tow a MT vehicle with front wheel on Freeing trapped vehicle the ground, perform the following procedures. SCE0841Z WARNING Front 1. Turn the ignition switch to the “OFF” position. • Never allow anyone to stand near the towing 2. Secure the steering wheel in a straight-ahead line during the pulling operation. position with rope or a similar device. • Never spin the tyres at high speed. This could 3. Move the shift lever to the N (Neutral) position. cause them to explode and result in serious 4. Release the parking brake. injury. Parts of the vehicle could also overheat and be damaged. 5. Attach the safety chains whenever towing. In the event that your vehicle’s tyres become trapped Rear wheels on the ground: in sand, snow, or mud, and the vehicle is unable to 1. Turn the ignition switch to the “OFF” position. free itself without being pulled, use the recovery hooks. SCE0847Z 2. Move the shift lever to the N (Neutral) position. Rear Use the recovery hooks only. Do not attach the 3. Release the parking brake. • j pulling device to any other part of the vehicle 1 : Remove the hook cover from the bumper with a 4. Attach safety chains whenever towing. body. Otherwise, the vehicle body may be dam- suitable tool. All four wheels on the ground: aged. NISSAN recommends that the vehicle be placed on • Use the recovery hooks to free a vehicle only. a flatbed tow truck as illustrated. • The recovery hooks are under tremendous stress Manual Transmission (MT) model: when used to free a trapped vehicle. Always pull the pulling device straight out from the vehicle. If you have to tow a MT vehicle with all four wheels Never pull on the recovery hooks at an angle. on the ground, perform the following procedures.

In case of emergency 6-9 SCE0833Z j2 : Securely install the recovery hook as illustrated. The hook is stored with the jacking tools. Make sure that the recovery hook is properly secured in its storage area after use.

SCE0850Z Rear Do not use the rear hooks j3 to pull the vehicle.

6-10 In case of emergency 7 Appearance and care

Cleaning exterior...... 7-2 Floor mats ...... 7-4 Washing...... 7-2 Glass ...... 7-4 Removing spots...... 7-2 Seat belts ...... 7-4 Waxing...... 7-2 Corrosion protection...... 7-4 Glass ...... 7-3 Most common factors contributing to vehicle Underbody ...... 7-3 corrosion ...... 7-4 Wheels...... 7-3 Environmental factors influence the rate of Aluminium alloy wheels ...... 7-3 corrosion ...... 7-4 Chrome parts ...... 7-3 To protect your vehicle from corrosion ...... 7-5 Cleaning interior ...... 7-3 CLEANING EXTERIOR

In order to maintain the appearance of your vehicle, CAUTION REMOVING SPOTS it is important to take proper care of it. • Do not wash the vehicle with strong house- Remove tar and oil spots, industrial dust, insects, Whenever possible, park your vehicle inside a ga- hold soap, strong chemical detergents, petrol and tree sap as quickly as possible from the paint rage or in a covered area to minimise the chances or solvents. surface to avoid lasting damage or staining. Special of damaging the paint surface of your vehicle. • Do not wash the vehicle in direct sunlight or cleaning products are available at a NISSAN dealer When it is necessary to park outside, park in a shady while the vehicle body is hot, as the paint sur- or qualified workshop or any automotive accessory area or protect the vehicle with a body cover. Be face may become water-spotted. store. careful not to scratch the paint surface when put- Avoid using tight-napped or rough cloths, WAXING ting on or removing the body cover. • such as washing mitts. Care must be taken Regular waxing protects the paint surface and helps WASHING when removing caked-on dirt or other foreign maintain a new vehicle appearance. substances so the paint surface is not In the following instances, wash your vehicle as soon scratched or damaged. After waxing, polishing is recommended to remove as possible to protect the paint surface: built-up residue and to avoid a weathered appear- 3. Rinse the vehicle thoroughly with plenty of clean ance. • After a rainfall, which may cause the paint sur- water. face damage from acid rain. A NISSAN dealer or qualified workshop can assist 4. Use a dampened chamois to dry the paint sur- you in choosing the appropriate waxing products. • After driving on coastal roads, which may cause face and avoid leaving water spots. rusting from the sea breeze. CAUTION When washing the vehicle, take care of the follow- • When contaminants such as soot, bird drop- ing: • Wash your vehicle thoroughly and completely pings, tree sap, metal particles or bugs get on before applying wax to the paint surface. the paint surface. • Inside flanges, joints and folds on the doors, hatches and bonnet are particularly vulnerable to • Always follow the manufacturer’s instructions • When dust or mud builds up on the paint sur- the effects of road salt. Therefore, these areas supplied with the wax. face. must be cleaned regularly. • Do not use a wax containing any abrasives, 1. Wash the vehicle surface with a wet sponge and Be sure that the drain holes in the lower edge of cutting compounds or cleaners that may dam- plenty of water. • the doors are not clogged. age the vehicle finish. 2. Clean the vehicle surface gently and thoroughly Spray water to the underbody and in the wheel Machine compounding or aggressive polishing on a using a mild soap, a special vehicle soap or a • wells to loosen the dirt and/or wash away road base coat/clear coat paint finish may dull the finish general purpose dishwashing liquid mixed with salt. or leave swirl marks. clean, lukewarm (never hot) water.

7-2 Appearance and care CLEANING INTERIOR

GLASS ALUMINIUM ALLOY WHEELS Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner Use glass cleaner to remove smoke and dust film Wash the wheels regularly with a sponge damp- or soft bristled brush. Wipe the vinyl and leather sur- from the glass surfaces. It is normal for glass to ened in a mild soap solution, especially during win- faces with a clean, soft cloth dampened in mild soap become coated with a film after the vehicle is parked ter in areas where road salt is used. The salt residue solution, then wipe clean with a dry, soft cloth. in the hot sun. Glass cleaner and a soft cloth will from road salt could discolour the wheels if it is not easily remove this film. washed off regularly. Regular care and cleaning is required in order to maintain the appearance of the leather. UNDERBODY CAUTION Before using any fabric protector, read the manu- In areas where road salt is used in the winter, it is Follow the directions below to avoid staining or facturer’s recommendations. Some fabric protec- necessary to clean the vehicle’s underbody regu- discolouring the wheels: tors contain chemicals that may stain or bleach the larly in order to prevent dirt and salt from building up • Do not use a cleaner that uses strong acid or seat material. and causing the acceleration of corrosion on the alkali contents to clean the wheels. underbody and suspension. Use a soft cloth dampened only with water to clean • Do not apply wheel cleaners to the wheels the meter and gauge lens covers. Before the winter and again in the spring, the under- when they are hot. The wheel temperature CAUTION seal must be checked and, if necessary, re-treated. should be the same as ambient temperature. WHEELS • Never use benzine, thinner or any similar ma- • Rinse the wheel to completely remove the terial. • Wash the wheels when washing the vehicle to cleaner within 15 minutes after the cleaner is maintain their appearance. applied. • Small dirt particles can be abrasive and damaging to leather surfaces and should be re- • Clean the inner side of the wheels when the CHROME PARTS moved promptly. Do not use saddle soap, car wheel is changed or the underside of the vehicle Clean all chrome parts regularly with a nonabrasive waxes, polishes, oils, cleaning fluids, is washed. chrome polish to maintain the finish. solvents, detergents or ammonia-based • Do not use abrasive cleaners when washing the cleaners as they damage the natural leather wheels. finish. • Inspect wheel rims regularly for dents or corro- • Never use fabric protectors unless recom- sion. This may cause loss of pressure or damage mended by the manufacturer. the tyre bead. • Do not use glass or plastic cleaner on meter • NISSAN recommends that the road wheels be or gauge lens covers. It may damage the lens waxed to protect against road salt in areas where covers. it is used during winter.

Appearance and care 7-3 CORROSION PROTECTION

FLOOR MATS GLASS MOST COMMON FACTORS The use of Genuine NISSAN floor mats (where fit- Use glass cleaner to remove smoke and dust film CONTRIBUTING TO VEHICLE ted) can extend the life of your vehicle carpet and from the glass surfaces. It is normal for glass to CORROSION make it easier to clean the interior. Regardless of become coated with a film after the vehicle is parked • The accumulation of moisture-retaining dirt and what mats are used, be sure they are fitted for your in the hot sun. Glass cleaner and a soft cloth will debris in body panel sections, cavities, and other vehicle and are properly positioned in the foot well easily remove this film. areas. to prevent interference with pedal operation. Mats CAUTION should be maintained with regular cleaning and re- • Damage to the paint surface and other protec- placed if they become excessively worn. When cleaning the inside of the windows, do not tive coatings caused by gravel and stone chips use sharp-edged tools, abrasive cleaners or chlo- or minor traffic accidents. rine-based disinfectant cleaners. They could ENVIRONMENTAL FACTORS damage the electrical conductors, such as rear window defogger elements. INFLUENCE THE RATE OF CORROSION SEAT BELTS Moisture WARNING The accumulation of sand, dirt and water on the • Do not allow wet seat belts to roll up in the inside floor of the vehicle can accelerate corrosion. retractor. Wet floor carpet/floor mats will not dry completely SAI0034Z inside the vehicle. They should be removed and Example • Never use bleach, dye or chemical solvents to completely dried to avoid floor panel corrosion. clean the seat belts, since these materials Floor mat positioning aid may severely weaken the seat belt webbing. Relative humidity j This vehicle includes front floor mat brackets Ato The seat belts can be cleaned by wiping them with Corrosion will be accelerated in areas of high rela- act as a floor mat positioning aid. NISSAN floor a sponge dampened in a mild soap solution. tive humidity. mats have been specially designed for your vehicle model. Allow the belts to dry completely in the shade before Temperature using them. (See “Seat belts” in the “1. Safety — Position the mat by placing the floor mat bracket High temperatures accelerate the rate of corrosion seats, seat belts and supplemental restraint system” to those parts which are not well ventilated. hook through the floor mat grommet hole while cen- section.) tering the mat in the foot area. Corrosion will also be accelerated in areas where Periodically check that the mats are properly posi- the temperatures stay above freezing. tioned.

7-4 Appearance and care Air pollution deterioration of underbody components such as the exhaust system, fuel and brake lines, brake cables, Industrial pollution, the presence of salt in the air in floor pan and fenders. coastal areas, or heavy road salt use accelerates the corrosion process. Road salt also accelerates In the winter, the underbody must be cleaned the disintegration of paint surfaces. periodically. TO PROTECT YOUR VEHICLE FROM For additional protection against rust and corrosion, CORROSION which may be required in some areas, consult a NISSAN dealer or qualified workshop. • Wash and wax your vehicle often to keep the vehicle clean. • Always check for minor damage to the paint surface and if any exists, repair it as soon as possible. • Keep the drain holes in the lower edge of the doors open to avoid water accumulation. • Check the vehicle underbody for accumulation of sand, dirt or salt. If present, wash with water as soon as possible. CAUTION • Never remove dirt, sand or other debris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner. • Never allow water or other liquids to come in contact with electronic components inside the vehicle as this may damage them. Chemicals used for road surface deicing are extremely corrosive. They accelerate corrosion and

Appearance and care 7-5 NOTE

7-6 Appearance and care 8 Maintenance and do-it-yourself

Maintenance requirements ...... 8-2 Air cleaner filter...... 8-14 Scheduled maintenance...... 8-2 Wiper blades ...... 8-15 General maintenance...... 8-2 Windscreen wiper blades ...... 8-15 Where to go for service ...... 8-2 Rear window wiper blade ...... 8-16 General maintenance...... 8-2 Window washer fluid ...... 8-16 Explanation of general maintenance items ...... 8-2 Battery...... 8-17 Maintenance precautions ...... 8-4 Vehicle battery...... 8-17 Engine compartment check locations ...... 8-5 Integrated keyfob battery ...... 8-18 Engine cooling system ...... 8-5 Intelligent key battery ...... 8-19 Checking engine coolant level...... 8-5 Fuses ...... 8-20 Changing engine coolant ...... 8-6 Engine compartment...... 8-20 Engine oil...... 8-6 Passenger compartment...... 8-21 Checking engine oil level ...... 8-6 Lights ...... 8-21 Changing engine oil and oil filter ...... 8-7 Headlights ...... 8-21 Protect environment...... 8-9 Exterior lights...... 8-22 Fuel filter (diesel engine model)...... 8-9 Interior lights...... 8-22 Draining water ...... 8-9 Light locations ...... 8-23 Bleeding fuel system...... 8-10 Tyres and wheels...... 8-26 Drive belt ...... 8-11 Tyre inflation pressure...... 8-26 Spark plugs (petrol engine model)...... 8-11 Types of tyres...... 8-26 Platinum-tipped spark plugs...... 8-11 Tyre chains...... 8-27 Brakes...... 8-12 Tyre rotation ...... 8-27 Checking parking brake...... 8-12 Tyre wear and damage ...... 8-27 Checking footbrake pedal...... 8-12 Tyre age ...... 8-27 Brake booster...... 8-13 Changing tyres and wheels...... 8-28 Brake fluid ...... 8-13 Wheel balance...... 8-28 Clutch fluid ...... 8-14 Spare tyre ...... 8-28 MAINTENANCE REQUIREMENTS GENERAL MAINTENANCE

Your new vehicle has been designed to have mini- These checks and inspections can be done by your- During normal day-to-day operation of the vehicle, mum maintenance requirements with long service self, a qualified technician, or if you prefer, a general maintenance should be performed regularly intervals to save you both time and money. How- NISSAN dealer or qualified workshop. as prescribed in this section. If you detect any un- ever, some day-to-day and regular maintenance is usual sounds, vibrations or smells, be sure to check essential to maintain your vehicle’s fine mechanical WHERE TO GO FOR SERVICE for the cause or have a NISSAN dealer or qualified condition, as well as its emission and engine perfor- If maintenance service is required or your vehicle workshop do it promptly. In addition, you should mance. appears to malfunction, have the systems checked notify a NISSAN dealer if you think that repairs are required. It is the owner’s responsibility to make sure that the and tuned by a NISSAN dealer or qualified work- specified maintenance, as well as general mainte- shop. When performing any checks or maintenance work, nance, is performed. NISSAN technicians are well-trained specialists and closely observe “Maintenance precautions” later in this section. As the vehicle owner, you are the only one who can are kept up-to-date with the latest service informa- ensure that your vehicle receives the proper mainte- tion through technical bulletins, service tips, and in- EXPLANATION OF GENERAL nance care. You are a vital link in the maintenance ternal dealership training programs. They are com- be- MAINTENANCE ITEMS chain. pletely qualified to work on NISSAN’s vehicles fore they work on your vehicle, rather than after they Additional information on the following items with SCHEDULED MAINTENANCE have worked on it. “*” is found later in this section. For your convenience, the required scheduled main- You can be confident that a NISSAN dealer or quali- Outside vehicle tenance items are described and listed in a separate fied workshop’s service department performs the maintenance booklet. You must refer to that booklet best job to meet the maintenance requirements on The maintenance items listed here should be per- to ensure that necessary maintenance is performed your vehicle — in a reliable and economic way. formed from time to time, unless otherwise speci- on your vehicle at regular intervals. fied. GENERAL MAINTENANCE Doors and engine bonnet: Check that all doors and the engine bonnet operate General maintenance includes those items which properly. Also make sure that all latches lock se- should be checked during normal day-to-day opera- curely. Lubricate hinges and latches if necessary. tion of the vehicle. They are essential if your vehicle Make sure that the secondary latch of the engine is to continue to operate properly. It is your respon- bonnet keeps the bonnet from opening when the sibility to perform these procedures regularly as pre- primary latch is released. scribed. When driving in areas using road salt or other cor- Performing general maintenance checks requires rosive materials, check lubrication frequently. minimal mechanical skill and only a few general automotive tools.

8-2 Maintenance and do-it-yourself Lights*: Wiper blades*: Warning lights and chimes: Clean the headlights on a regular basis. Make sure Check for cracks or wear if they do not wipe prop- Make sure that all warning lights and chimes are that the headlights, stop lights, tail lights, turn signal erly. operating properly. lights, and other lights are all operating properly and Windscreen defogger: installed securely. Also check the aim of the head- Inside vehicle lights. The maintenance items listed here should be Check that the air comes out of the defogger outlets properly and in good quantity when operating the Tyres*: checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle, etc. heater or air conditioner. Check the pressure with a gauge often and always Windscreen wiper and washer*: prior to long distance trips. If necessary, adjust the Accelerator pedal: pressure in all tyres, including the spare, to the pres- Check the pedal for smooth operation and make Check that the wipers and washer operate properly sure specified. Check carefully for damage, cuts or sure that the pedal does not catch or require uneven and that the wipers do not streak. excessive wear. effort. Keep the floor mats away from the pedal. Under bonnet and vehicle Tyre rotation*: Brake pedal*: The maintenance items listed here should be Tyres should be rotated every 10,000 km (6,000 Check the pedal for smooth operation and make checked periodically (for example, each time you miles). sure that it has the proper distance under it when check the engine oil or refuel). However, the timing for tyre rotation may vary ac- depressed fully. Check the brake booster function. Battery*: Keep the floor mats away from the pedal. cording to your driving habits and the road surface Check the fluid level in each cell. It should be be- Parking brake*: conditions. tween the UPPER and LOWER levels. Vehicles op- Wheel alignment and balance: Check that the lever has the proper distance of erated in high temperatures or under severe condi- If the vehicle should pull to either side while driving travel. tions require frequent checks of the battery fluid on a straight and level road, or if you detect uneven Seat belts: level. or abnormal tyre wear, there may be a need for Check that all parts of the seat belt system (for Brake fluid level*: wheel alignment. example, buckles, anchors, adjusters and retrac- Make sure that the brake fluid level is between the If the steering wheel or seat vibrates at normal high- tors) operate properly and smoothly, and that they MAX and MIN lines on the reservoir. way speeds, wheel balancing may be needed. are installed securely. Check the belt webbing for Clutch fluid level*: cuts, fraying, wear or damage. Windscreen: Make sure that the clutch fluid level is between the Steering wheel: Clean the windscreen on a regular basis. Check the MAX and MIN lines on the reservoir. windscreen at least every six months for cracks or Check for changes in the steering conditions, such Engine coolant level*: other damage. Have a damaged windscreen re- as excessive free play, hard steering or strange paired by a qualified repair facility. noises. Check the coolant level when the engine is cold.

Maintenance and do-it-yourself 8-3 Engine drive belts*: • Be sure the ignition switch is in the “OFF” or dealer or qualified workshop because the fuel lines are under high pressure even when the Make sure that the drive belts are not frayed, worn, LOCK position when performing any parts re- engine is turned off. cracked or oily. placement or repairs. Engine oil level*: • Do not work under the bonnet while the en- • Your vehicle is equipped with an automatic gine is hot. Always turn off the engine and engine cooling fan. It may come on at any Check the level on the dipstick after parking the wait until it cools down. time without warning, even if the ignition vehicle on a level surface and turning off the engine. switch is in the “OFF” position and the engine If you must work with the engine running, • is not running. To avoid injury, always discon- Fluid leaks: keep your hands, clothing, hair and tools away nect the negative battery cable before work- Check under the vehicle for fuel, oil, water or other from moving fans, belts and any other moving ing near the fan. fluid leaks after the vehicle has been parked for a parts. while. Water dripping from the air conditioner after Always wear eye protection whenever you It is advisable to secure or remove any loose • use is normal. If you should notice any leaks or if fuel • work on your vehicle. clothing and any jewellery, such as rings, fumes are evident, check for the cause and have it watches, etc. before working on your vehicle. Never leave the engine or transmission re- corrected immediately. • lated component harness connector discon- If you must run the engine in an enclosed Window washer fluid*: • nected while the ignition switch is in the ON space such as a garage, be sure there is position. Check that there is adequate fluid in the reservoir. proper ventilation for exhaust gases to es- MAINTENANCE PRECAUTIONS cape. NISSAN GREEN PROGRAM Never get under the vehicle while it is sup- Avoid direct contact with used engine oil and When performing any inspection or maintenance • ported only by a jack. If it is necessary to work coolant. Improperly disposed engine oil, en- work on your vehicle, always take care to prevent under the vehicle, support it with safety gine coolant, and/or other vehicle fluids can serious accidental injury to yourself or damage to stands. hurt the environment. Always conform to lo- the vehicle. The following are general precautions cal regulations for disposal of vehicle fluids. which should be closely observed. • Keep smoking materials, flame and sparks away from fuel and the battery. This “8. Maintenance and do-it-yourself” section provides instructions regarding only those items WARNING Never connect or disconnect either the bat- • which are relatively easy for an owner to perform. • Park the vehicle on a level surface, apply the tery or any transistorised component connec- parking brake securely and block the wheels tor while the ignition switch is in the ON posi- You should be aware that incomplete or improper to prevent the vehicle from moving. Move the tion. servicing may result in operating difficulties or excessive emissions, and could affect your warranty shift lever to the N (Neutral) position. On petrol engine models with the Multiport • coverage. If in doubt about any servicing, have it Fuel Injection (MFI) system, the fuel filter and done by a NISSAN dealer or qualified workshop. fuel lines should be serviced by a NISSAN

8-4 Maintenance and do-it-yourself ENGINE COMPARTMENT CHECK ENGINE COOLING SYSTEM LOCATIONS

For an overview of the engine compartment, see WARNING CHECKING ENGINE COOLANT “Engine compartment” in the “0. Illustrated table LEVEL of contents” section. • Never remove the radiator or coolant reservoir cap when the engine is hot. Serious burns could be caused by high-pressure fluid escaping from the radiator. Wait until the engine and radiator cool down. • Engine coolant is poisonous and should be stored carefully in marked containers out of the reach of children. The engine cooling system is filled at the factory with a high-quality, year-round, anti-freeze coolant SDI2456Z solution. The anti-freeze solution contains rust and HR16DE engine corrosion inhibitors, therefore additional cooling system additives are not necessary. CAUTION When adding or replacing coolant, be sure to use only Genuine NISSAN Engine Coolant or equivalent in its quality with the proper mixture ratio. Use Genuine NISSAN Engine Coolant or equivalent in its quality. Genuine NISSAN Engine Coolant is a pre-mixed (mixture ratio 50%) type coolant. SDI2463Z The use of other types of coolant solutions may K9K engine damage the engine cooling system. HR16DE engine model For HR16DE engine model: The radiator is equipped with a pressure cap. To prevent engine damage, Check the coolant level in the reservoir tank when the engine is cold. If the coolant level is below the use only a Genuine NISSAN radiator cap or its j j equivalent when replacement is required. MIN level 2 , add coolant up to the MAX level 1. If the reservoir tank is empty, check the coolant level in the radiator when the engine is cold. If there is insufficient coolant in the radiator, fill the radiator

Maintenance and do-it-yourself 8-5 ENGINE OIL with coolant up to the filler opening and also add it • Avoid direct skin contact with used coolant. If CHECKING ENGINE OIL LEVEL to the reservoir tank up to the MAX level j1. skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible. If the cooling system frequently requires coolant, have it checked by a NISSAN dealer or qualified • Keep coolant out of the reach of children and workshop. pets. K9K engine model NISSAN GREEN PROGRAM Check the coolant level in the reservoir when the Engine coolant must be disposed of properly. engine is cold. If the coolant level is below the MIN Check your local regulations. j j level 2 , add coolant up to the MAX level 1. Engine coolant must be disposed of properly. Check If the cooling system frequently requires coolant, your local regulations. SDI1305AZ have it checked by a NISSAN dealer or qualified HR16DE engine workshop. CHANGING ENGINE COOLANT Contact a NISSAN dealer or qualified workshop if replacement is required. Major engine cooling system repair should be performed by a NISSAN dealer or qualified workshop. The service procedures can be found in the appropriate NISSAN Service Manual. Improper servicing can result in reduced heater per- SDI2464Z formance and engine overheating. K9K engine 1. Park the vehicle on a level surface and apply the WARNING parking brake. • To avoid being scalded, never change the 2. Start the engine and warm it up until the engine coolant when the engine is hot. temperature reaches the normal operating tem- • Never remove the radiator or coolant reser- perature (approximately 5 minutes). voir cap when the engine is hot. Serious burns 3. Stop the engine. could be caused by high pressure fluid escaping from the radiator.

8-6 Maintenance and do-it-yourself 4. Wait at least 10 minutes for the engine oil to ers, etc. It should be disposed of at proper 6. Remove the plastic engine undercover, if neces- drain back to the oil pan. waste facilities. We recommend having your sary, by removing the bolts and plastic clips. oil changed by a NISSAN dealer or qualified 5. Remove the dipstick and wipe it clean. workshop. 6. Reinsert the dipstick all the way. • Be careful not to burn yourself, as the engine 7. Remove the dipstick and check the oil level. It oil may be hot. should be within the range jC. • Prolonged and repeated contact with used 8. If the oil level is below jA , remove the oil filler engine oil may cause skin cancer. cap and pour the recommended oil into the open- Avoid direct skin contact with used oil. If con- ing. Do not overfill jB. • tacted, wash thoroughly with soap or hand

When filling the engine oil, do not remove the cleaner and plenty of water as soon as pos- SDI2458Z dipstick. sible. HR16DE engine 9. Recheck the oil level with the dipstick. • Store used engine oil in marked containers j1 Oil drain plug out of the reach of children. It is normal to add some oil between oil main- j2 Oil filter tenance intervals or during the running-in pe- 1. Park the vehicle on a level surface and apply the riod, depending on the severity of operating parking brake. Engine oil and filter conditions. 2. Start the engine and warm it up until the engine HR16DE engine: CAUTION temperature reaches the normal operating tem- 1. Place a large drain pan under the drain plug. perature (approximately 5 minutes). The oil level should be checked regularly. Oper- 2. Remove the drain plug with a wrench. ating your vehicle with an insufficient amount of 3. Stop the engine. oil can damage the engine, and such damage is 3. Remove the oil filler cap and completely drain the not covered by the warranty. 4. Wait at least 10 minutes for the engine oil to oil. drain back to the oil pan. CHANGING ENGINE OIL AND OIL If the oil filter is to be changed, remove and re- 5. Raise and support the vehicle using a suitable place it at this time. FILTER floor jack and safety jack stands. CAUTION Place the safety jack stands under the vehicle WARNING • Waste oil must be disposed of properly. Check jack-up points. NISSAN GREEN PROGRAM your local regulations. • A suitable adapter should be attached to the jack Used oil must be disposed of properly. Never stand saddle. 4. Loosen the oil filter with an oil filter wrench. pour or dump oil into the ground, canals, riv- 5. Remove the oil filter by turning it by hand.

Maintenance and do-it-yourself 8-7 6. Wipe the oil filter mounting surface with a clean 14. Dispose of the used oil in the proper manner. 4. Loosen the oil filter with an oil filter wrench. cloth. Check your local regulations. 5. Remove the oil filter by turning it by hand. Be sure to remove any old gasket remaining on 15. Check the engine oil level according to the 6. Wipe the entire oil filter mounting surface with a the mounting surface. proper procedure. (See “Checking engine oil clean cloth. level” earlier in this section.) 7. Apply new engine oil to the gasket of the new oil Be sure to remove any old gasket remaining on filter. the mounting surface. 8. Screw in the oil filter until a slight resistance is 7. Apply new engine oil to the gasket on the new oil felt and then tighten an additional 2/3 of a turn to filter. secure the filter. Drain plug tightening torque: Oil filter tightening torque: K9K engine HR16DE engine 44 N•m 15 to 20 N•m (4.5 kg-m, 32 ft-lb) (1.5 to 2.0 kg-m, 11 to 15 ft-lb) 8. Screw in the oil filter until a slight resistance is 9. Clean and reinstall the drain plug and new SDI2465Z felt, and then tighten an additional 3/4 of a turn to washer. Securely tighten the drain plug with a K9K engine secure the filter. wrench. Do not use excessive force. j1 Oil drain plug Oil filter tightening torque: Drain plug tightening torque: K9K engine HR16DE engine j2 Oil filter 25 N•m 29 to 39 N•m K9K engine: (2.6 kg-m, 18 ft-lb) (3.0 to 4.0 kg-m, 22 to 29 ft-lb) 1. Place a large drain pan under the drain plug. 9. Clean and reinstall the drain plug and new 10. Refill the recommended engine oil and quantity. 2. Remove the drain plug with a wrench. washer. Securely tighten the drain plug with a (See “Recommended fuel/lubricants and wrench. Do not use excessive force. capacities” in the “9. Technical information” 3. Remove the oil filler cap and completely drain the section.) oil. 10. Refill the recommended engine oil and quantity. (See “Recommended fuel/lubricants and When filling the engine oil, do not remove If the oil filter is to be changed, remove and re- capacities” in the “9. Technical information” the dipstick. placeitatthistime. section.) 11. Securely install the oil filler cap. CAUTION 11. Securely install the oil filler cap. 12. Start the engine. Waste oil must be disposed of properly. Check 12. Start the engine. your local regulations. 13. Check the drain plug and the oil filter for any sign of leakage.

8-8 Maintenance and do-it-yourself FUEL FILTER (diesel engine model)

13. Check the drain plug and the oil filter for any DRAINING WATER sign of leakage. Drain water in the fuel filter according to the mainte- 14. Dispose of the used oil in the proper manner. nance log shown in a separate maintenance book- Check your local regulations. let. 15. Check the engine oil level according to the Warning light and chime (where fitted) proper procedure. (See “Checking engine oil level” earlier in this section.) If the water-in-fuel-filter warning light illuminates and/or a chime sounds while the engine is After operation running, there might be water in the fuel filter. 1. Install the engine undercover (if removed) into position as the following steps. a. Pull the centre of each plastic clip out. b. Hold the engine undercover into position. c. Insert the clips through the undercover into the hole in the frame, then push the centre of the clipsintolocktheclipsinplace. d. Screw in the bolts, then tighten them. 2. Lower the vehicle carefully to the ground. PROTECT ENVIRONMENT NISSAN GREEN PROGRAM SDI2466 It is illegal to pollute drains, watercourses and soil. Use authorised waste collection facilities, including Operation civil amenity sites and garages providing facilities The fuel filter and the priming pump are located near for disposal of used oil and used oil filters. If in the fuel tank under the vehicle. doubt, contact your local authority for advice on disposal. Drain the water in the fuel filter according to the following procedure: The regulations concerning the pollution of the environment will vary from country to country. 1. Remove the fuel filter protector j1.

Maintenance and do-it-yourself 8-9 2. Connect a suitable drain hose j2 to the drain BLEEDING FUEL SYSTEM 3. Squeeze the priming pump j1 several times until valve j3. there is a sudden resistance felt in the pressure, then stop. 3. Place a container j4 under the fuel filter. 4. Crank the engine until it starts. Do not crank the 4. Loosen the drain valve j3 4 to 5 turns to drain engine for more than 30 seconds. the water. To avoid dropping it, do not loosen the drain valve too much. If water does not drain 5. If the engine does not start, stop cranking and properly, operate the priming pump j5 . (The repeat step 3 above. priming pump can also be accessed from the 6. If the engine does not operate smoothly after it inside of the vehicle. See “Bleeding fuel system” has started, race it two or three times. later in this section.) If the engine does not start after performing the 5. After the water has been completely drained, above procedures, see a NISSAN dealer or quali- close the drain valve j3. fied workshop. 6. Bleed any air from the fuel system. (See “Bleed- ing fuel system” later in this section.)

SDI2467

Bleed air out of the fuel system after refilling an empty fuel tank by the following procedure: 1. Slide the front right-side seat forward. 2. Turn the clips clockwise to remove the cover and access the priming pump j1.

8-10 Maintenance and do-it-yourself DRIVE BELT SPARK PLUGS (petrol engine model)

3. Alternator WARNING 4. Air conditioner compressor (where fitted) Be sure the engine and ignition switch are off ▼: Tension checking point (model without air and that the parking brake is applied. conditioner) Replace the spark plugs according to the mainte- Be sure the ignition switch is in the “OFF” position. nance log shown in a separate maintenance book- Visually inspect the belt for signs of unusual wear, let. cuts, fraying or looseness. Check regularly for con- If replacement is required, contact a NISSAN dealer dition and tension. If the belt is in poor condition or or qualified workshop. SDI1862Z loose, have it replaced or adjusted by a NISSAN HR16DE engine model dealer or qualified workshop. PLATINUM-TIPPED SPARK PLUGS 1. Water pump 2. Alternator 3. Crankshaft pulley 4. Air conditioner compressor (where fitted) ▼: Tension checking point

SDI2020Z

It is not necessary to replace the platinum-tipped spark plugs as frequently as the conventional type of spark plugs. These spark plugs are designed to last much longer than the conventional type of spark plugs. SDI2468Z CAUTION K9K engine Do not reuse the platinum-tipped spark plugs 1. Crankshaft pulley • by cleaning or re-gapping. 2. Drive belt auto-tensioner (where fitted)

Maintenance and do-it-yourself 8-11 BRAKES

• Always replace with the recommended plati- CHECKING PARKING BRAKE num-tipped spark plugs. WARNING See a NISSAN dealer or qualified workshop for a brake system check if the footbrake pedal height does not return to normal. With the engine running, check the distance jA between the upper surface of the pedal and the upper surface of the steering hole cover. If it is out the range listed, see a NISSAN dealer or qualified workshop. SDI1447AZ jA : 80 mm (3.15 in) or more under a depressing force of 490 N (50 kg, 110 lb) Lever type Self-adjusting brakes From the released position, pull the parking brake Your vehicle is equipped with self-adjusting brakes. lever up slowly and firmly. If the number of clicks is The disc-type brakes self-adjust every time the foot- out of the range listed, see a NISSAN dealer or brake pedal is applied. qualified workshop. 6 to 7 clicks Brake pad wear warning Pulling force 196 N (20 kg, 44 lb) The disc brake pads have audible wear warnings. When a brake pad requires replacement, it will make CHECKING FOOTBRAKE PEDAL a high pitched scraping sound when the vehicle is in motion. This scraping sound will first occur only when the brake pedal is depressed. After more wear of the brake pad, the sound will always be heard even if the brake pedal is not depressed. Have the brakes checked as soon as possible if the wear warning sound is heard. Under some driving or climate conditions, occasional brake squeaks, squeals or other noises may be heard. Occasional brake noise during light to SDI2453Z moderate stops is normal and does not affect the function or performance of the brake system.

8-12 Maintenance and do-it-yourself BRAKE FLUID

Proper brake inspection intervals should be “Recommended fuel/lubricants and capacities” in followed. For additional information, see a separate WARNING the “9. Technical information” section for recom- maintenance booklet. • Use only new fluid from a sealed container. mended types of fluid.) BRAKE BOOSTER Old, inferior, or contaminated fluid may dam- If the fluid must be added frequently, the system age the brake system. The use of improper should be thoroughly checked by a NISSAN dealer Check the brake booster function as follows: fluids can damage the brake system and af- or qualified workshop. fect the vehicle’s stopping ability. 1. With the engine off, depress and release the footbrake pedal several times. When the brake • Clean the filler cap before removing. pedal movement (distance of travel) remains the Brake fluid is poisonous and should be stored same from one pedal application to the next, con- • carefully in marked containers out of the reach tinue on to the next step. of children. 2. While depressing the footbrake pedal, start the CAUTION engine. The pedal height should drop a little. Do not spill the fluid on painted surfaces. This 3. With the footbrake pedal depressed, stop the will damage the paint. If fluid is spilled, wash it engine. Keep the pedal depressed for about 30 off with plenty of water immediately. seconds. The pedal height should not change. 4. Run the engine for 1 minute without depressing the footbrake pedal, then turn it off. Depress the footbrake pedal several times. The pedal travel distance will decrease gradually with each de- pression as the vacuum is released from the booster. If the brakes do not operate properly, have the brakes checked by a NISSAN dealer or qualified workshop. SDI2459Z

Check the fluid level in the reservoir. If the fluid is below the MIN line j2 , the brake warning light will illuminate. Add fluid up to the MAX line j1 . (See

Maintenance and do-it-yourself 8-13 CLUTCH FLUID AIR CLEANER FILTER

If the fluid must be added frequently, the clutch sys- WARNING tem should be thoroughly checked by a NISSAN • Use only new fluid from a sealed container. dealer or qualified workshop. Old, inferior, or contaminated fluid may damage the clutch system. • Clean the filler cap before removing. • Clutch fluid is poisonous and should be stored carefully in marked containers out of the reach of children. SDI2106Z CAUTION

Do not spill the clutch fluid on painted surfaces. WARNING This will damage the paint. If clutch fluid is spilled, wash it off with plenty of water immediately. Operating the engine with the air cleaner filter off can cause you or others to be burned. The air cleaner filter not only cleans the intake air, it also stops flame if the engine backfires. If the air cleaner filter is not installed and the engine backfires, you could be burned. Never drive with the air cleaner filter off. Be cautious working on the engine when the air cleaner filter is off. To remove the filter, push the tabs, and pull the unit upward. SDI2459Z The viscous paper type filter element should not be cleaned and reused. The dry paper type filter ele- Check the fluid level in the reservoir. If the fluid is ment may be cleaned and reused. Replace the air below the MIN line j2 , add fluid up to the MAX line filter according to the maintenance log shown in a j1 . (See “Recommended fuel/lubricants and separate maintenance booklet. capacities” in the “9. Technical information” section When replacing the air filter, wipe the inside of the for the recommended types of fluid.) air cleaner housing and the cover with a damp cloth.

8-14 Maintenance and do-it-yourself WIPER BLADES

WINDSCREEN WIPER BLADES Cleaning If the windscreen does not become clear after using the windscreen washer or if the wiper blades chat- ter when operating the windscreen wipers, wax or other materials may be on the windscreen and/or wiper blades. Clean the outside of the windscreen surface with a washer solution or mild detergent. Your windscreen is clean if beads do not form when rinsing with water. Clean the blade by wiping it with a cloth soaked in a washer solution or a mild detergent. Rinse the blade with water. If your windscreen is still not clear after cleaning the blades and using the wipers, replace the blades.

SDI2362 SDI1649Z

Be careful not to clog the washer nozzle jA . This Replacing may cause improper windscreen washer operation. If the nozzle is clogged, remove any objects with a 1. Lift the wiper arm away from the windscreen. needle or small pin jB . Be careful not to damage 2. Push and hold the release tab jA , and then move the nozzle. the wiper blade down the wiper arm to remove j1. 3. Remove the wiper blade.

Maintenance and do-it-yourself 8-15 WINDOW WASHER FLUID

4. Insert the new wiper blade onto the wiper arm until it clicks into place. CAUTION • After wiper blade replacement, return the wiper arm to its original position. Otherwise the wiper arm or the engine bonnet may be scratched and may cause damage when the engine bonnet is opened.

• Worn wiper blades can damage the wind- SDI2460Z screen and impair driver vision. REAR WINDOW WIPER BLADE WARNING Contact a NISSAN dealer or qualified workshop if checking or replacement is required. Anti-freeze is poisonous and should be stored carefully in marked containers out of the reach of children. Regularly check the fluid level in the reservoir and add fluid if necessary. Add a washer solvent to the water for better cleaning. In the winter season, add a windscreen washer anti-freeze. Follow the manufacturer’s instructions for the mixture ratio.

8-16 Maintenance and do-it-yourself BATTERY

VEHICLE BATTERY

Caution symbols for battery m WARNING WARNING No smoking Do not operate the vehicle if the fluid in the bat- Never smoke around the battery. Never expose the battery to open flames or j1 No exposed flames tery is low. Low battery fluid can cause a higher electrical sparks. m No sparks load on the battery which can generate heat, reduce battery life, and in some cases lead to an Handle the battery cautiously. Always wear eye protection glasses to protect explosion. j2 Shield eyes m against explosion or battery acid. Checking battery fluid level Check the fluid level in each cell. The battery fluid Keep away from Never allow children to handle the battery. Keep the battery out of reach of level should be between the UPPER LEVEL j1 and j3 m children children. LOWER LEVEL j2 lines. Do not allow battery fluid to contact your skin, eyes, fabrics, or painted surfaces. If it is necessary to add fluid, add only demineralised/ After handling the battery or battery cap, immediately wash your hands distilled water to bring the level to the indicator in thoroughly. If the battery fluid gets into your eyes, or onto your skin or clothing, each filler opening. Do not overfill. j4 Battery acid flush with water immediately for at least 15 minutes and seek medical attention. 1. Remove the cell plugs j3 (where fitted) using a m Battery fluid is acid. If the battery fluid gets into your eyes or onto your skin, it could cause loss of your eyesight or burns. suitable tool. 2. Add demineralised/distilled water up to the UP- Note operating Before handling the battery, read this instruction carefully to ensure correct and j j5 PER LEVEL 1 line. instructions safe handling. m If the side of the battery is not clear, check the distilled water level by looking directly above the j j6 Explosive gas Hydrogen gas, generated by battery fluid, is explosive. cell; the condition A indicates OK and the con- m dition jB needs more to be added. 3. Replace and tighten the cell plugs. • Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level.

Maintenance and do-it-yourself 8-17 • Keep the battery surface clean and dry. Clean • There is danger of explosion if lithium battery the battery with a solution of baking soda and is incorrectly replaced. Replace only with the water. same or equivalent type. • Make certain the terminal connections are clean and securely tightened. • If the vehicle is not to be used for more than 30 days, disconnect the negative (−) battery terminal cable to prevent battery discharge. Jump starting If jump starting is necessary, see “Jump starting” in the “6. In case of emergency” section. If the engine does not start by jump starting or the battery does not charge, the battery may have to be replaced. Contact a NISSAN dealer or qualified workshop for replacing the battery. INTEGRATED KEYFOB BATTERY Battery replacement CAUTION • Be careful not to allow children to swallow the battery and removed parts. SDI1808 NISSAN GREEN PROGRAM To replace the battery: An improperly disposed battery can harm the environment. Always confirm local regulations 1. Use an appropriate tool to remove the screw jA for battery disposal. and open the lid jB. • When changing batteries, do not let dust or oil 2. Replace the battery with a new one. get on the components. Recommended battery: CR2016 or equivalent

8-18 Maintenance and do-it-yourself • Do not touch the internal circuit and electric Recommended battery: CR2032 or equivalent terminals as doing so could cause a malfunc- Do not touch the internal circuits and electric ter- tion. • minals as doing so could cause a malfunction. Make sure that the + side faces the bottom of • Make sure that the + side faces the bottom of the the case jC. • case. 3. Close the lid and install the screw securely. See a NISSAN dealer or qualified workshop if you 4. Operate the buttons to check its operation. need assistance for replacement. See a NISSAN dealer or qualified workshop if you need assistance for replacement. INTELLIGENT KEY BATTERY Battery replacement CAUTION • Be careful not to allow children to swallow the battery and removed parts. NISSAN GREEN PROGRAM • An improperly disposed battery can harm the environment. Always confirm local regulations for battery disposal. • When changing batteries, do not let dust or oil SDI2094 get on the components. • There is danger of explosion if lithium battery To replace the battery: is incorrectly replaced. Replace only with the 1. Slide the locking pin j1 to the unlock position. same or equivalent type. 2. Remove the Intelligent Key cap as illustrated j2. 3. Use an appropriate tool to remove the screw j3 and open the lid j4. 4. Replace the battery with a new one.

Maintenance and do-it-yourself 8-19 FUSES

ENGINE COMPARTMENT vehicle while pushing the tabs j5 and pulling all sides of the fuse cover. Then remove the tabs j5 and j6 , and lift the fuse holder cover j7. 5. Locate the fuse that needs to be replaced. 6. Remove the fuse using the fuse puller located in the passenger compartment fuse box.

SDI2489Z

SDI2622Z Fusible links CAUTION If any electrical equipment does not operate and the Never use a fuse of a higher or lower amperage fuses are in good condition, check the fusible links rating than that specified on the fuse box cover. in the holders j1,j2 and j3 . If any of these fusible This could damage the electrical system or cause SDI1753Z links are melted, replace only with Genuine NISSAN a fire. parts. If any electrical equipment does not operate, check 7. If the fuse is open jA , replace it with a new fuse For checking and replacing the fusible links in holder for an open fuse. jB. j3 , see a NISSAN dealer or qualified workshop. 1. Be sure the ignition switch is in the “OFF” posi- If the new fuse also opens, after installing, have the tion. electrical system checked, and if necessary repaired, by a NISSAN dealer or qualified work- 2. Be sure the headlight switch is in the “OFF” shop. position. 3. Open the engine bonnet. 4. Remove the fuse/fusible link holder cover by pushing the tab j1 and lifting the cover from the right side j2 , then the left side j3. Remove the fuse holder cover by removing the tabs j4 on the rear side and front side of the

8-20 Maintenance and do-it-yourself LIGHTS

HEADLIGHTS Fog may temporarily form inside the lens of the exterior lights in the rain or in a car wash. A temperature difference between the inside and the outside of the lens causes the fog. This is not a malfunction. If large drops of water collect inside the lens, contact a NISSAN dealer or qualified workshop. Replacing halogen headlight bulb SDI2461Z The halogen headlight is a semi-sealed beam type which uses replaceable headlight (halogen) bulbs. They can be replaced from inside the engine com- PASSENGER COMPARTMENT partment without removing the headlight assembly. CAUTION CAUTION Never use a fuse of a higher or lower amperage High-pressure halogen gas is sealed inside the rating than that specified on the fuse box cover. bulb. The bulb may break if the glass envelope is This could damage the electrical system or cause scratched or the bulb is dropped. a fire. 1. Disconnect the battery negative cable. If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch is in the “OFF” posi- SDI1753Z tion. 6. If the fuse is open jA , replace it with a new fuse 2. Be sure the headlight switch is in the “OFF” j position. B. 3. Remove the fuse box cover. If the new fuse also opens, after installing, have the electrical system checked, and if necessary 4. Locate the fuse that needs to be replaced. repaired, by a NISSAN dealer or qualified work- 5. Remove the fuse using the fuse puller jA (Left- shop. hand drive model) or jB (Right-hand drive model).

Maintenance and do-it-yourself 8-21 6. Install the new bulb in the reverse order of re- EXTERIOR LIGHTS moval. Item Wattage (W) CAUTION Front turn signal light 21 • When handling the bulb, do not touch the Front clearance light 5 glass envelope. Front fog light (where fitted) 35 Side turn signal light 5 • Use the same number and wattage as origi- Rear combination light nally installed: Turn signal 21 Halogen headlight model Stop/Tail light 21/5 High beam bulb: 60W (H4) Rear fog light 21 Low beam bulb: 55W (H4) Reverse light 21 • Do not leave the bulb out of the headlight High-mounted stop light* 16 reflector for a long period of time as dust, Number plate light 5 moisture and smoke may enter the headlight body and affect the performance of the head- *: See a NISSAN dealer or qualified workshop for light. replacement. Aiming adjustment is not necessary if only the bulbs INTERIOR LIGHTS are replaced. When aiming adjustment is neces- Item Wattage (W) sary, contact a NISSAN dealer or qualified work- Room light 10 shop. Luggage compartment light 5

SDI2438

2. Disconnect the electrical connector j1 from the rear end of the bulb. 3. Pull off the rubber cap j2. 4. Push and turn the retaining pin j3 to loosen it. 5. Remove the headlight bulb. Do not shake or ro- tate the bulb when removing it.

8-22 Maintenance and do-it-yourself LIGHT LOCATIONS 1. Front turn signal light 2. Room light 3. Front fog light (where fitted) 4. Clearance light 5. Headlight 6. Side turn signal light 7. Luggage compartment light 8. High-mounted stop light 9. Stop/tail light 10. Rear fog light*1 or Reverse light*2 11. Number plate light 12. Reverse light*1 or Rear fog light*2 13. Rear turn signal light 14. Room light (where fitted) *1: Left-Hand Drive (LHD) model *2: Right-Hand Drive (RHD) model

NDI1244

Maintenance and do-it-yourself 8-23 SDI2440Z Front turn signal light

SDI2441Z

SDI2306 Clearance light

: REMOVE : INSTALL Replacement procedures All other lights are either type A, B, C, D or E. When replacing a bulb, first remove the lens and/or cover.

SDI2442 Front fog light (where fitted)

8-24 Maintenance and do-it-yourself SDI2454Z Number plate light

SDI1845Z

SDI2445 SDI2446 Room light Side turn signal light Rear combination light

jA : Bolts

Maintenance and do-it-yourself 8-25 TYRES AND WHEELS

If you have a flat tyre, see “Flat tyre” in the “6. In All season tyres case of emergency” section. NISSAN specifies all season tyres on some models TYRE INFLATION PRESSURE to provide good performance all year, including snowy and icy road conditions. All season tyres are Periodically check the pressure of the tyres, includ- identified by ALL SEASON and/or M&S on the tyre ing the spare. An incorrect tyre pressure may ad- sidewall. Snow tyres have better snow traction than versely affect tyre life and vehicle handling. The tyre all season tyres and may be more appropriate in pressure should be checked when tyres are COLD. some areas. Tyres are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than Summer tyres SDI1724Z 1.6 km (1 mile). COLD tyre pressures are shown on Luggage compartment light the tyre placard. NISSAN specifies summer tyres on some models to provide superior performance on dry roads. Sum- Insufficient pressure can lead to an overheating of mer tyre performance is substantially reduced in the tyre and subsequent internal damage. At high snow and ice. Summer tyres do not have the tyre speeds, this could result in tread separation and traction rating M&S on the tyre sidewall. even bursting of the tyre. If you plan to operate your vehicle in snowy or icy TYPES OF TYRES conditions, NISSAN recommends the use of snow CAUTION or all season tyres on all four wheels. When changing or replacing tyres, be sure all Snow tyres four tyres are of the same type (that is, summer, If snow tyres are needed, it is necessary to select all season or snow) and construction. A NISSAN tyres equivalent in size and load rating to the original dealer may be able to help you with information equipment tyres. If you do not, it can adversely af- about tyre type, size, speed rating and availabil- fect the safety and handling of your vehicle. ity. Generally, snow tyres have lower speed ratings than Replacement tyres may have a lower speed rating factory equipped tyres and may not match the po- than the factory equipped tyres, and they may not tential maximum vehicle speed. Never exceed the match the potential maximum vehicle speed. Never maximum speed rating of the tyre. If you install snow exceed the maximum speed rating of the tyre. tyres, they must be the same size, brand, construction and tread pattern on all four wheels. For additional traction on icy roads, studded tyres may be used. However, some states and provinces

8-26 Maintenance and do-it-yourself prohibit their use. Check local, state and provincial TYRE ROTATION TYRE WEAR AND DAMAGE laws before installing studded tyres. Skid and traction capabilities of studded snow tyres on wet or dry surfaces may be poorer than that of non-studded snow tyres. TYRE CHAINS Use of tyre chains may be prohibited according to location. Check the local laws before installing tyre chains. When installing tyre chains, make sure that they are of proper size for the tyres on your vehicle and are installed according to the chain manufactur- SDI1662Z SDI1663Z er’s instructions. Use chain tensioners when recommended by the NISSAN recommends that tyres be rotated every j1 Wear indicator 10,000 km (6,000 miles). However, the timing for tyre chain manufacturer to ensure a tight fit. Loose j2 Wear indicator location mark end links of the tyre chains must be secured or tyre rotation may vary according to your driving hab- removed to prevent the possibility of whipping ac- its and the road surface conditions. (See “Flat tyre” Tyres should be periodically inspected for wear, tion damage to the fenders or underbody. If pos- in the “6. In case of emergency” section for the tyre cracking, bulging or objects caught in the tread. If sible, avoid fully loading your vehicle when using replacement.) excessive wear, cracks, bulging or deep cuts are tyre chains. In addition, drive at a reduced speed. found, the tyre should be replaced immediately. Otherwise, your vehicle may be damaged and/or WARNING The original tyres have a built-in tread wear indica- vehicle handling and performance may be adversely • After rotating the tyres, adjust the tyre pres- tor. When the wear indicator is visible, the tyre affected. sure. should be replaced. Tyre chains must be installed only on the front • Retighten the wheel nuts when the vehicle Improper service of a spare tyre may result in seri- wheels and not on the rear wheels. Do not use the has been driven for 1,000 km (600 miles) (also ous personal injury. If it is necessary to repair the chains on dry roads. in cases of a flat tyre, etc.). spare tyre, contact a NISSAN dealer or qualified workshop. Do not drive with tyre chains on paved roads which • Incorrect tyre selection, fitting, care, or main- are clear of snow. Driving with chains in such condi- tenance can affect vehicle safety with risk of TYRE AGE tions can cause damage to the various mechanisms accident and injury. If in doubt, consult a Never use a tyre over six years old, regardless of of the vehicle due to some overstress. NISSAN dealer or the tyre manufacturer. whether it has been used or not. Tyres degrade with age as well as with the vehicle

Maintenance and do-it-yourself 8-27 usage. Have your tyres checked and balanced often WHEEL BALANCE by a repair shop or, if you prefer, a NISSAN dealer. Unbalanced wheels may affect vehicle handling and CHANGING TYRES AND WHEELS tyre life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as WARNING required. Do not install a deformed wheel or tyre even if it SPARE TYRE has been repaired. Such wheels or tyres could have structural damage and could fail without Conventional spare tyre warning. A standard tyre (the same size as the road wheels) When replacing a tyre, use the same size, speed is supplied with your vehicle. rating and load carrying capacity as originally equipped. (See “Tyres and wheels” in the “9. Tech- nical information” section for recommended types and sizes of tyres and wheels.) The use of tyres other than those recommended or the mixed use of tyres of different brands, construction (bias, bias- belted, or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to-tyre clearance, snow chain clearance, speedometer calibration, headlight aim and bumper height. Some of these effects may lead to accidents and could result in serious personal injury. If the wheels are changed for any reason, always replace with wheels which have the same offset dimension. Wheels of a different offset could cause early tyre wear, possibly degraded vehicle handling characteristics and/or interference with the brake discs/drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear.

8-28 Maintenance and do-it-yourself 9 Technical information

Recommended fuel/lubricants and capacities...... 9-2 Vehicle Identification Number (chassis Fuel recommendation ...... 9-4 number)...... 9-7 Recommended SAE viscosity number...... 9-4 Engine serial number ...... 9-7 Air conditioner system refrigerant and lubricant ... 9-5 Tyre placard ...... 9-8 Engine ...... 9-5 Air conditioner specification label (where Tyres and wheels...... 9-6 fitted)...... 9-8 Dimensions...... 9-6 Radio approval number and information ...... 9-8 When travelling or registering in another country ...... 9-6 Remote keyless entry system (where fitted)...... 9-8 Vehicle identification ...... 9-7 Intelligent Key system (where fitted)...... 9-8 Vehicle identification label ...... 9-7 NISSAN Anti-Theft System (NATS) Vehicle Identification Number (VIN) plate ...... 9-7 immobilizer ...... 9-11 RECOMMENDED FUEL/LUBRICANTS AND CAPACITIES

The following are approximate capacities. The actual refill quantities may be slightly different. When refilling, follow the procedures instructed in the “8. Maintenance and do-it-yourself” section to determine the proper refill capacity. Capacity (Approximate) Recommended fuel and lubricants Litre Imp measure Fuel 55 12-1/8 gal See “Fuel recommendation” later in this section. Engine oil (Refill) (*1) HR16DE With oil filter 4.3 3-3/4 qt (Petrol engine) • Genuine NISSAN engine oil (*2) Without oil filter 4.1 3-5/8 qt • API grade SL or SM, ILSAC grade GF-3 or GF-4, ACEA A1/B1, A3/B3, A3/B4, A5/B5, C2 or C3 (*2) K9K With oil filter 4.4 3-7/8 qt (Diesel engine) • Genuine NISSAN engine oil (*2) Without oil filter 4.2 3-3/4 qt • ACEA A1/B1 (*2), (*3) • Viscosity SAE 5W-30 (*2) Cooling system (with reservoir) total HR16DE 6.3 5-1/2 qt Genuine NISSAN Engine Coolant or equivalent in its quality (*4) K9K 6.5 5-3/4 qt reservoir HR16DE 0.7 5/8 qt K9K 0.4 3/8 qt Manual Transmission (MT) gear oil — — Genuine NISSAN gear oil (ETL8997B) 75W-80 or equivalent (*5) Brake and clutch fluid Refill to the proper fluid level accord- Genuine NISSAN Brake Fluid or equivalent DOT 3 or DOT 4 (*6) ing to the instructions in the “8. Maintenance and do-it-yourself” section. Multi-purpose grease — — NLGI No. 2 (Lithium soap base) Air conditioner system refrigerant — — HFC-134a (R-134a) Air conditioner system lubricants — — NISSAN A/C System Oil Type R (HR16DE engine), Type S (K9K engine) or an exact equivalent

9-2 Technical information *1: For additional information, see “Engine oil” in the “8. Maintenance and do-it-yourself” section. *2: For further details, see “Recommended SAE viscosity number” later in this section. *3: With the technical performances of oil ACEA A3/B4. *4: Use Genuine NISSAN Engine Coolant, or equivalent in its quality, in order to avoid possible aluminium corrosion within the engine cooling system caused by the use of non-genuine engine coolant. Note that any repairs for the incidents within the engine cooling system while using non-genuine engine coolant may not be covered by the warranty even if such incidents occurred during the warranty period. *5: If Genuine NISSAN gear oil (ETL8997B) 75W-80 is not available, API GL-4, Viscosity SAE 75W-80 may be used as a temporary replacement. However, use Genuine NISSAN gear oil as soon as it is available. *6: Never mix different types of fluids (DOT3 and DOT4).

Technical information 9-3 FUEL RECOMMENDATION CAUTION RECOMMENDED SAE VISCOSITY Petrol engine (model with three-way • Do not use home heating oil, petrol or other NUMBER catalyst) alternate fuels in the diesel engine, this can Outside Temperature Range cause engine damage. Anticipated Before Next Oil Change CAUTION • Do not add petrol or other alternate fuels to PETROL AND DIESEL ENGINE OIL Do not use leaded petrol. Using leaded petrol will diesel fuel. damage the three-way catalyst. • Do not use summer fuel at temperatures be- Use UNLEADED PREMIUM petrol of at least 95 low –7°C (20°F). The cold temperatures will octane (RON). cause wax to form in the fuel. As a result, it may prevent the engine from running If unleaded premium petrol is not used, UNLEADED smoothly. REGULAR petrol with an octane rating of at least 91 (RON) may be used at slightly reduced performance. However, for maximum vehicle performance and the best driveability, the use of unleaded premium petrol is recommended. Diesel engine* EN590 Diesel fuel of at least 51 cetane must be used. NOTE Use only low sulphur diesel. * If two types of diesel fuel are available, use summer or winter fuel properly according to the following temperature conditions. NTI187 • Above −7°C (20°F) ... Summer type diesel Petrol engine oil fuel. m 5W-30 is preferable. • Below −7°C (20°F) ... Winter type diesel fuel. If 5W-30 is not available, select the viscosity, from If you are in any doubt, please consult a NISSAN the chart, that is suitable for the outside tem- dealer or qualified workshop. perature range.

9-4 Technical information ENGINE

Diesel engine oil 5W-30 is preferable. Engine model HR16DE K9K Petrol, 4-cycle, Diesel, 4-cycle If 5W-30 is not available, select the viscosity, from Type DOHC the chart, that is suitable for the outside temperature range. Cylinder arrangement 4-cylinder, in-line 4-cylinder, in-line 78.0 × 83.6 76.0 × 80.5 Bore × Stroke mm (in) AIR CONDITIONER SYSTEM (3.071 × 3.291) (2.992 × 3.169) REFRIGERANT AND LUBRICANT Displacement cm3 (cu in) 1,598 (97.51) 1,461 (89.15) The air conditioner system of your vehicle must be Idle speed rpm 650±50 850 charged with the refrigerant HFC-134a (R134a) and Ignition timing (B.T.D.C.) degree at idle 6°±5 — the lubricant NISSAN A/C System Oil Type R (for Spark plugs the HR16DE engine model), Type S (for the K9K Type Standard PLZKAR6A-11 — engine model) or equivalents. Use of any other re- Gap mm (in) 1.1 (0.043) — frigerants or lubricants will cause severe damage, and you may need to replace your vehicle’s entire Camshaft operation Timing chain Timing belt air conditioner system. NISSAN GREEN PROGRAM The release of refrigerants into the atmosphere is prohibited in many countries and regions. The refrigerant HFC-134a (R-134a) in your vehicle will not harm the Earth’s ozone layer. However, it may contribute in a small part to the global warming effect. NISSAN recommends that the refrigerant be appro- priately recovered and recycled. Contact a NISSAN dealer or qualified workshop when servicing the air conditioner system.

Technical information 9-5 TYRES AND WHEELS DIMENSIONS WHEN TRAVELLING OR REGISTERING IN ANOTHER COUNTRY

Tyre size Standard Spare Unit: mm (in) When planning to travel in another country or region, find out whether the fuel required for your 175/70 R14C Conventional Overall length 4,400 (173.2) Overall width 1,695 (66.7) vehicle is available in that country or region. Using a Overall height 1,860 (73.2) low octane rated fuel may cause engine damage. Road Size Offset mm Therefore, be sure that the required fuel is available wheel (in) Front tread 1,490 (58.7) Rear tread 1,510 (59.4) wherever you go. For additional information regard- Steel 14 × 5.5JJ 45 (1.77) ing recommended fuel, see earlier in this section. Aluminium 14 × 5.5J 45 (1.77) Wheelbase 2,725 (107.3) When transferring the registration of your vehicle to another country, state, province or district, contact the appropriate authorities to find out that the vehicle complies with the local legal requirements. In some cases, a vehicle cannot meet the legal requirements, and it may be necessary to modify the vehicle to meet local laws and regulations. In addition, there may be possibilities that a vehicle cannot be adapted in certain areas. The laws and regulations for motor vehicle emission control and safety standards vary according to the country, state, province or district; therefore, the vehicle specification may differ. When any vehicles are to be taken into another country, state, province or district, its modification, transportation, registration, and any other expenses which may result, are the responsibility of the user. NISSAN is not responsible for any inconveniences that may result.

9-6 Technical information VEHICLE IDENTIFICATION

VEHICLE IDENTIFICATION LABEL VEHICLE IDENTIFICATION NUMBER ENGINE SERIAL NUMBER (chassis number)

STI0655Z STI0466Z

STI0656Z HR16DE engine The label is attached as shown in the front passenger’s side centre pillar. The vehicle identification number is stamped as VEHICLE IDENTIFICATION NUMBER shown. (VIN) PLATE

STI0662Z K9K engine The engine serial number is stamped on the engine as shown.

STI0537Z

The vehicle identification number plate j1 is attached as shown. This number is the identification for your vehicle and is used in the vehicle registration.

Technical information 9-7 RADIO APPROVAL NUMBER AND INFORMATION

TYRE PLACARD REMOTE KEYLESS ENTRY SYSTEM INTELLIGENT KEY SYSTEM (where fitted) (where fitted)

STI0657Z

The cold tyre pressures are shown on the tyre placard affixed to the driver’s side centre pillar. AIR CONDITIONER SPECIFICATION LABEL (where fitted)

STI0527Z STI0663

STI0658Z

The air conditioner specification label is attached to the underside of the bonnet as shown.

9-8 Technical information STI0664 STI0665 STI0666

Technical information 9-9 STI0667 STI0668 STI0669

9-10 Technical information NISSAN ANTI-THEFT SYSTEM (NATS) IMMOBILIZER

STI0670 STI0671 Model without Intelligent Key system Intelligent Key system (where fitted) STI0672 Model with Intelligent Key system

Technical information 9-11 NOTE

9-12 Technical information NOTE

Technical information 9-13 NOTE

9-14 Technical information NOTE

Technical information 9-15 NOTE

9-16 Technical information NOTE

Technical information 9-17 NOTE

9-18 Technical information 10 Index

Brake A – Anti-lock Braking System (ABS) ...... 5-15 – Brake booster ...... 8-13 Adjusting time ...... 2-27 – Brake fluid ...... 8-13 Air cleaner filter ...... 8-14 – Brake precautions ...... 5-15 Air conditioner – Brake system ...... 5-15 – Air conditioner specification label ...... 9-8 – Brakes ...... 8-12 – Air conditioner system refrigerant and lubricant ...... 9-5 – Checking footbrake pedal ...... 8-12 – Heater and air conditioner ...... 4-4 – Checking parking brake ...... 8-12 – Manual air conditioner ...... 4-5 – Hand brake ...... 3-24 – Servicing air conditioner ...... 4-7 – Parking brake ...... 3-24 Antenna ...... 4-9 – Trailer brakes ...... 5-13 Anti-lock Braking System (ABS) ...... 5-15 Ashtray ...... 2-28 C Audible reminders ...... 2-16 Audible reminders, warning/indicator lights ...... 2-10 Car phone or CB radio ...... 4-16 Audio operation precautions ...... 4-8 Card holder ...... 2-31 Audio system ...... 4-8 Care when driving ...... 5-4 CD Player/LW-MW-FM radio ...... 4-10 B Centre vents ...... 4-4 Changing Back door ...... 3-20 – Changing engine coolant ...... 8-6 – Locking or unlocking back door ...... 3-20 – Changing engine oil and oil filter ...... 8-7 Battery ...... 5-17, 8-17 – Changing tyres and wheels ...... 8-28 – Battery saver system ...... 2-20, 2-34, 2-35 – Checking engine oil level ...... 8-6 – Integrated keyfob battery ...... 8-18 Checking – Intelligent key battery ...... 8-19 – Checking bulbs ...... 2-10 Before starting engine ...... 5-2 – Checking engine coolant level ...... 8-5 Bleeding fuel system ...... 8-10 – Checking engine oil level ...... 8-6 Blocking wheels ...... 6-3 – Checking footbrake pedal ...... 8-12 – Checking parking brake ...... 8-12 Bonnet ...... 3-19 Child restraint anchorage ...... 1-15 D Child restraint installation using 3-point type seat belt ...... 1-18 Child restraints ...... 1-11 Defogger switch ...... 2-24 – Child restraint anchorage ...... 1-15 Diesel engine ...... 5-7 – Child restraint installation using 3-point type seat belt ..... 1-18 Digital clock ...... 2-27 – ISOFIX child restraint system ...... 1-14 Child safety ...... 1-8 Dimensions ...... 9-6 Cleaning Display – Aluminium alloy wheels ...... 7-3 – Instrument brightness control ...... 2-3 – Chrome parts ...... 7-3 – Vehicle information display ...... 2-4 – Cleaning exterior ...... 7-2 Door locks ...... 3-4 – Cleaning interior ...... 7-3 Doors – Glass ...... 7-3, 7-4 – French doors ...... 3-21 – Removing spots ...... 7-2 – Tailgate ...... 3-20 – Seat belts ...... 7-4 Draining water ...... 8-9 – Underbody ...... 7-3 Drive belt ...... 8-11 – Wheels ...... 7-3 Driving Clock (digital) ...... 2-27 – Care when driving ...... 5-4 Closing bonnet ...... 3-19 – Cold weather driving ...... 5-17 Clutch fluid ...... 8-14 – Driving in wet conditions ...... 5-4 Cold weather driving ...... 5-17 – Driving in winter conditions ...... 5-4 Console box ...... 2-29 – Driving vehicle ...... 5-8 Coolant – Driving with Manual Transmission (MT) ...... 5-8 – Precautions when starting and driving ...... 5-2 – Changing engine coolant ...... 8-6 – Engine coolant ...... 5-17 Corrosion E – Corrosion protection ...... 5-18, 7-4 – Environmental factors influence the rate of corrosion ...... 7-4 Electronic Stability Programme (ESP) system ...... 5-9 – To protect your vehicle from corrosion ...... 7-5 – Electronic Stability Programme (ESP) OFF switch ...... 5-10 Coupling device installation ...... 5-13 Engine ...... 9-5 Cup holders ...... 2-29 – Before starting engine ...... 5-2 – Changing engine coolant ...... 8-6 – Changing engine oil and oil filter ...... 8-7 – Checking engine coolant level ...... 8-5 – Checking engine oil level ...... 8-6 – Diesel engine ...... 5-7

10-2 Index – Engine cold start period ...... 5-4 – Recommended fuel/lubricants and capacities ...... 9-2 – Engine compartment ...... 0-11, 8-20 Fuses ...... 8-20 – Engine compartment check locations ...... 8-5 – Engine coolant ...... 5-17 – Engine cooling system ...... 8-5 G – Engine oil ...... 8-6 – Engine overheat ...... 6-7 Gauges – Fuel filter ...... 8-9 – Fuel gauge ...... 2-2 – Petrol engine ...... 5-6 – Instrument brightness control ...... 2-3 – Spark plugs ...... 8-11 – Meters and gauges ...... 2-2 – Starting engine ...... 5-6 General maintenance ...... 8-2 Engine oil level information display ...... 2-9 Glove box ...... 2-28 Exhaust gas ...... 5-2 Explanation of general maintenance items ...... 8-2 Exterior lights ...... 8-22 H

Hand brake ...... 3-24 F Hazard indicator flasher switch ...... 2-24 Head restraint Flat tyre ...... 6-2 – Adjustment ...... 1-6 Floor mats ...... 7-4 Headlight Fluid – Headlight switch ...... 2-17 – Brake fluid ...... 8-13 – Headlights ...... 8-21 – Clutch fluid ...... 8-14 – Manual aiming control ...... 2-18 – Window washer fluid ...... 8-16 Headlight aiming control ...... 2-18 Fog light Heater and air conditioner ...... 4-4 – Front fog light ...... 2-21 Horn ...... 2-25 – Rear fog light ...... 2-21 How to read the displayed lines ...... 4-2 French doors ...... 3-21 Front door ...... 3-5 Fuel I – Fuel filler cap ...... 3-22 – Fuel filler lid ...... 3-22 Ignition switch ...... 5-4 – Fuel filter ...... 8-9 Ignition switch cap ...... 3-4 – Fuel gauge ...... 2-2 Immobilizer ...... 3-2 – Fuel recommendation ...... 9-4 Indicator lights ...... 2-10, 2-14 – Opening fuel filler lid ...... 3-22

Index 10-3 Indicators for maintenance ...... 2-6 – Remote keyless entry system ...... 3-8, 9-8 Indicators for operation ...... 2-4 – Using Intelligent Key system ...... 3-12 Injured persons ...... 1-9 – Using remote keyless entry system ...... 3-8 Installing spare tyre ...... 6-5 Instrument panel ...... 0-8 L – LHD models ...... 0-8 – RHD models ...... 0-9 Light Integrated keyfob ...... 3-2 – Exterior lights ...... 8-22 Integrated keyfob battery ...... 8-18 – Fog light switch ...... 2-21 Intelligent key battery ...... 8-19 – Headlight switch ...... 2-17 Intelligent Key system ...... 3-10, 5-4, 9-9 – Headlights ...... 8-21 – Intelligent Key ...... 3-3 – Indicator lights ...... 2-10, 2-14 – Intelligent Key operating range ...... 3-11 – Interior lights ...... 2-34, 8-22 – Troubleshooting guide ...... 3-16 – Light locations ...... 8-23 Interior lights ...... 2-34, 8-22 – Lights ...... 8-21 – Room light ...... 2-34 – Luggage compartment light ...... 2-34 ISOFIX child restraint system ...... 1-14 – Trailer direction indicator light ...... 2-10 – Warning lights ...... 2-10, 2-11 Lock J – Anti-lock Braking System (ABS) ...... 5-15 – Door locks ...... 3-4 Jump starting ...... 6-6 – Locking with inside lock knob ...... 3-5 – Locking with key ...... 3-5 – Power door lock switch ...... 3-6 K – Steering lock ...... 5-6 – Super Lock System ...... 3-4 Key Luggage – Ignition switch cap ...... 3-4 – Loading luggage ...... 5-4 – Intelligent Key ...... 3-3 – Luggage compartment light ...... 2-34 – Intelligent key battery ...... 8-19 Luggage compartment light ...... 2-34 – Intelligent Key operating range ...... 3-11 – Battery saver system ...... 2-35 – Intelligent Key system ...... 3-10, 5-4, 9-9 Luggage hooks ...... 2-32 – Key positions ...... 5-6 – Keys ...... 3-2 – Locking with key ...... 3-5 – Mechanical key ...... 3-4 – NISSAN Anti-Theft System (NATS) key ...... 3-2

10-4 Index – Checking engine oil level ...... 8-6 M Opening bonnet ...... 3-19 Operating precautions (Trailer towing) ...... 5-12 Maintenance Operating range ...... 3-11 – Explanation of general maintenance items ...... 8-2 – Maintenance precautions ...... 8-4 Overheat (Engine) ...... 6-7 – Maintenance requirements ...... 8-2 – Scheduled maintenance ...... 8-2 P Manual Transmission (MT) ...... 5-5 Mechanical key ...... 3-4 Parking ...... 5-11 Meter and gauges – Checking parking brake ...... 8-12 – Digital clock ...... 2-27 – Parking brake ...... 3-24 Meters and gauges ...... 2-2 Passenger compartment (Fuses) ...... 8-21 – Fuel gauge ...... 2-2 Petrol engine ...... 5-6 – Instrument brightness control ...... 2-3 Platinum-tipped spark plugs ...... 8-11 – Odometer ...... 2-2 – Speedometer ...... 2-2 Power – Tachometer ...... 2-7 – Electric power steering system ...... 5-14 Mirror – Power door lock switch ...... 3-6 – Inside rearview mirror ...... 3-23 – Power outlet ...... 2-27 – Mirrors ...... 3-23 – Power windows ...... 2-25 – Outside rearview mirrors ...... 3-23 Power outlet ...... 2-27 Most common factors contributing to vehicle corrosion ...... 7-4 Pre-tensioner seat belt system ...... 1-27 Precautions – Audio operation precautions ...... 4-8 N – Brake precautions ...... 5-15 – Child restraint usage ...... 1-11 NISSAN Anti-Theft System (NATS) ...... 3-18, 3-2, 5-7, 9-11 – Maintenance precautions ...... 8-4 NISSAN Anti-Theft System (NATS) Immobilizer ...... 3-2 – Operating precautions ...... 5-12 NISSAN Anti-Theft System (NATS) key ...... 3-2 – Precautions when starting and driving ...... 5-2 – Safety precautions ...... 4-2 – Seat belt usage ...... 1-7 O – Towing precautions ...... 6-8 Pregnant women ...... 1-8 Odometer ...... 2-2 Preparing tools and spare tyre ...... 6-2 Oil Protect – Changing engine oil and oil filter ...... 8-7 – Protect the environment ...... 8-9

Index 10-5 Protect environment ...... 8-9 – Seats ...... 1-2 Push starting ...... 6-7 – Second row seats ...... 1-3 – Third row seats ...... 1-5 Seat belt ...... 1-7 R – Child safety ...... 1-8 – Injured persons ...... 1-9 Radio – Precautions on seat belt usage ...... 1-7 – Car phone or CB radio ...... 4-16 – Pregnant women ...... 1-8 – CD Player/LW-MW-FM radio ...... 4-10 – Seat belt warning light ...... 2-10 Rear – Seat belts ...... 7-4 – Rear window wiper and washer operation ...... 2-23 – Three-point type seat belts ...... 1-9 Rear cooler ...... 4-7 Second row seats ...... 1-3 Rear vents ...... 4-4 Security system ...... 3-18 Rear view monitor ...... 4-2 – NISSAN Anti-Theft System (NATS) ...... 3-18 Servicing air conditioner ...... 4-7 Rear window wiper blade ...... 8-16 Side vents ...... 4-4 Recommended fuel/lubricants and capacities ...... 9-2 Sliding door ...... 3-7 Recommended SAE viscosity number ...... 9-4 Spare tyre ...... 6-2, 8-28 Remote keyless entry system ...... 3-8, 9-8 Spark plugs ...... 8-11 Removing tyre ...... 6-3 Special winter equipment ...... 5-17 Repair and replacement procedure ...... 1-27 Speedometer ...... 2-2 Room light ...... 2-34 Starting – Battery saver system ...... 2-34 Running-in schedule ...... 5-2 – Before starting engine ...... 5-2 – Jump starting ...... 6-6 – NISSAN Anti-Theft System (NATS) ...... 5-7 S – Precautions when starting and driving ...... 5-2 – Push starting ...... 6-7 Safety – Starting engine ...... 5-6 Steering – Child safety ...... 1-8 – Head restraints adjustment ...... 1-6 – Electric power steering system ...... 5-14 – Safety chains (Trailer towing) ...... 5-13 – Steering lock ...... 5-6 Scheduled maintenance ...... 8-2 – Steering wheel ...... 3-23 – Tilt operation ...... 3-23 Seat Stopping vehicle ...... 6-2 – Front seats – Adjustment ...... 1-2 Storage ...... 2-28 – Head restraints adjustment ...... 1-6 – Seat belts ...... 7-4 – Card holder ...... 2-31 – Console box ...... 2-29

10-6 Index – Cup holders ...... 2-29 Ticket holder ...... 2-31 – Glove box ...... 2-28 Tonneau cover ...... 2-32 – Luggage hooks ...... 2-32 Towing – Partition ...... 2-33 – Towing precautions ...... 6-8 – Ticket holder ...... 2-31 – Towing recommended by NISSAN ...... 6-9 – Tonneau cover ...... 2-32 – Towing your vehicle ...... 6-8 – Tray ...... 2-28 – Trailer towing ...... 5-12 – Under-seat tray ...... 2-29 – Trailer towing brakes ...... 5-13 – Utility hook ...... 2-31 – Trailer towing detection ...... 5-13 Stowing damaged tyre and tools ...... 6-5 Transmission Sun visors ...... 2-33 – Driving with Manual Transmission (MT) ...... 5-8 Super Lock System ...... 3-4 – Manual Transmission (MT) ...... 5-5 Supplemental air bag systems ...... 1-25 Trip computer ...... 2-6 Supplemental Restraint System (air bag system) Turn signal switch ...... 2-21 – Air bag system ...... 1-21 Tyre Switch – Changing spare tyre ...... 6-2 – Defogger switch ...... 2-24 – Changing tyres and wheels ...... 8-28 – Electronic Stability Programme (ESP) system ...... 5-9 – Flat tyre ...... 6-2 – Fog light switch ...... 2-21 – Installing spare tyre ...... 6-5 – Front fog light switch ...... 2-21 – Removing tyre ...... 6-3 – Hazard indicator flasher switch ...... 2-24 – Spare tyre ...... 8-28 – Ignition switch ...... 5-4 – Stowing damaged tyre and tools ...... 6-5 – Main lighting switch ...... 2-17 – Types of tyres ...... 8-26 – Power door lock switch ...... 3-6 – Tyre age ...... 8-27 – Rear fog light switch ...... 2-21 – Tyre chains ...... 8-27 – Turn signal switch ...... 2-21 – Tyre equipment ...... 5-17 – Windscreen wiper and washer switch ...... 2-22 – Tyre inflation pressure ...... 8-26 – Wiper and washer switch ...... 2-22 – Tyre placard ...... 9-8 – Tyre pressure ...... 5-12 – Tyre rotation ...... 8-27 T – Tyre wear and damage ...... 8-27 – Tyres and wheels ...... 8-26 Tachometer ...... 2-7 Tyre placard ...... 9-8 Tailgate ...... 3-20 Third row seats ...... 1-5 Three-point type seat belts ...... 1-9 Three-way catalyst ...... 5-3

Index 10-7 Windows ...... 2-25 U – Manual windows ...... 2-25 – Power windows ...... 2-25 Using remote keyless entry function ...... 3-13 – Sliding windows ...... 2-25 Using remote keyless entry system ...... 3-8 Windscreen wiper and washer switch ...... 2-22 Utility hook ...... 2-31 Windscreen wiper blades ...... 8-15 Wiper V – Rear window wiper and washer operation ...... 2-23 – Rear window wiper blade ...... 8-16 – Windscreen wiper and washer switch ...... 2-22 Vehicle battery ...... 8-17 – Windscreen wiper blades ...... 8-15 Vehicle identification ...... 9-7 – Wiper and washer switch ...... 2-22 – Vehicle identification label ...... 9-7 – Wiper blades ...... 8-15 – Vehicle Identification Number (chassis number) ...... 9-7 – Vehicle Identification Number (VIN) plate ...... 9-7 Vehicle information display ...... 2-4 Vehicle security ...... 5-16 Vents ...... 4-4

Warning – Warning lights ...... 2-11 Warning lights and audible reminders ...... 3-15 Warning/indicator lights and audible reminders ...... 2-10 Warnings and alerts ...... 2-5 Washing ...... 7-2 Waxing ...... 7-2 Wheel – Aluminium alloy wheels ...... 7-3 – Blocking wheels ...... 6-3 – Cleaning wheels ...... 7-3 Wheel balance ...... 8-28 When travelling or registering in another country ...... 9-6 Where to go for service ...... 8-2 Window washer fluid ...... 8-16

10-8 Index PETROL STATION INFORMATION

RECOMMENDED FUEL CAUTION TYRE COLD PRESSURE Petrol engine (model with three-way • Do not use home heating oil, petrol or other See the tyre placard affixed to the driver’s side catalyst) alternate fuels in the diesel engine, this can centre pillar. cause engine damage. CAUTION • Do not add petrol or other alternate fuels to Do not use leaded petrol. Using leaded petrol will diesel fuel. damage the three-way catalyst. • Do not use summer fuel at temperatures be- Use UNLEADED PREMIUM petrol of at least 95 low −7°C (20°F). Cold temperatures will cause octane (RON). wax to form in the fuel and may prevent the engine from running smoothly. If unleaded premium petrol is not used, UNLEADED REGULAR petrol with an octane rating of at least 91 RECOMMENDED ENGINE OIL (RON) may be used at slightly reduced performance. However, for maximum vehicle per- See “Recommended fuel/lubricants and capacities” formance and the best driveability, the use of un- in the “9. Technical information” section. leaded premium petrol is recommended. Petrol engine Diesel engine* • Genuine NISSAN engine oil EN590 Diesel fuel of at least 51 cetane must be • API grade: SL or SM used. • ILSAC grade: GF-3 or GF-4 NOTE • ACEA A1/B1, A3/B3, A3/B4, A5/B5, C2 or C3 Use only low sulphur diesel. Diesel engine * If two types of diesel fuel are available, use summer or winter fuel properly according to the fol- • Genuine NISSAN engine oil lowing temperature conditions. • ACEA A1/B1* • Above −7°C (20°F) ... Summer type diesel Viscosity SAE 5W-30 fuel. • * With the technical performances of oil ACEA A3/ • Below −7°C (20°F) ... Winter type diesel fuel. B4 ENVIRONMENT (End of Life Vehicles)

ENVIRONMENTAL CONCERN Manufacturing phase You can help prevent waste affecting the environment by bringing your NISSAN to be recycled at our NISSAN GREEN PROGRAM NISSAN plants based in the UK and Spain already collection networks in your area. Our collection net- Today, the efforts made by NISSAN to fulfil our achieve a recycling rate of over 90% and are look- works guarantee no cost for the treatment of your responsibilities to protect and sustain the environ- ing for further improvements. The UK plant installed ELV. For further information on how and where to ment are far-reaching. Within NISSAN, we promote 8 windmills to cut carbon dioxide emissions at power dispose of your ELV refer to your local NISSAN the highest levels of practice in every region and in plants by more than 3,000 tonnes per year. Since dealer or consult: www.nissan.eu. every area of operations. the end of March 2007, NMISA (Spain) uses a solar panel water heating system to save energy. This will PROTECT THE ENVIRONMENT COMPLIANCE AT EVERY STEP generate 33% of the energy consumed in the baths WHEN DRIVING during the painting of your vehicle. NISSAN focuses on ensuring that end of life vehicle Your driving behaviour has significant impact on fuel components are reused, recycled or recovered as Production and distribution phase economy and the environment. Follow the tips be- thermal energy, and guarantees compliance with EU low for better fuel-efficiency, better driving habits, Using resources efficiently to reduce the amount of legislation (the End of Life Vehicle Directive). and to be environmentally friendly by reducing emis- waste generated during the production and distribu- sions: WE BUILD OUR VEHICLES WITH tion stage. NISSAN promotes activities based on RECYCLING IN MIND Reducing, Reusing, and Recycling materials when- Defensive driving ever possible. The NISSAN GREEN PROGRAM Reducing landfill waste, emissions, conserving natu- 2010 (NGP2010) is our midterm environmental ac- Anticipating traffic conditions and acting accordingly ral resources, and enhancing recycling activities are tion plan defining our goals for achieving a 100% reduces fuel consumption, helping to protect of our emphasised daily in our manufacturing, sales and recycling rate for operations in Japan and globally. natural environment. Take your foot off the accelera- service operations and in the disposal of end of life tor while approaching traffic lights and avoid last vehicles (ELV). Use and service phase minute braking when the light turns red. Avoid speeding, harsh acceleration, and strong NISSAN dealers are our window to you, our cus- Design phase braking. The gain in time does not offset pollution of tomer. In order to meet your expectations they pro- the environment. Try to maintain speed when driving To reduce environmental impact we have developed vide not only high quality services but are also envi- uphill to reduce fuel consumption and pollution. your NISSAN vehicle to be 95% recyclable. We ronmentally responsible. NISSAN promotes activi- Maintain speed or allow the vehicle to go slower mark the components to facilitate dismantling, recy- ties to recycle the waste generated as a result of where traffic allows. cling and to reduce hazardous substances. We service centre activities. carefully verify and control substances of concern. Close windows when driving We have already reduced to a minimum the cad- Disposal phase mium, mercury and lead in your NISSAN vehicle. Driving with a window open at 100 km/h (62 MPH) Recycle your end of life vehicle or its components. NISSAN includes recycled material in your vehicle increases fuel consumption by up to 4%. Driving When your NISSAN reaches the end of its life, and and looks for opportunities to increase the percent- with the windows closed allows for better fuel is no longer suitable for daily use, it still has value. age of recycled materials used. economy. QUICK REFERENCE

Use the roof rack only when necessary Check your tyre pressure • In case of emergency ... 6-2 Only install the roof luggage system when you really Low tyre pressure increases fuel consumption as (Flat tyre, engine will not start, overheating, need it, otherwise put it inside the vehicle or store it well as the use of non-recommended tyres. Correct towing) in your garage. Do not drive around with an empty tyre pressure will maximise the grip of your vehicle How to start the engine ... 5-2 roof rack, kayak holder, or ski rack, this will reduce and optimise fuel consumption. • your aerodynamic drag significantly. • How to read the meters and gauges ... 2-2 Have your car serviced regularly • Maintenance and do-it-yourself ... 8-2 Optimise the use of air conditioning Regular service allows you to run your vehicle in The air conditioning system has a positive effect on optimal condition and with the best fuel efficiency. • Technical information ... 9-2 driving and vehicle safety through comfort cooling Have your vehicle serviced by your NISSAN dealer and dehumidifying, drivers are more alert and have or a qualified workshop to ensure that it is main- better visibility when window demisting/defogging tained to its original standard. becomes necessary. However, use of the air conditioning system will increase fuel consumption substantially in an urban environment. Optimise the use of air conditioning by using the vents as much as possible. Use the parking brake on slopes Use the parking brake when holding your vehicle on a slope. Avoid using the clutch to hold your vehicle as this leads to unnecessary fuel consumption and wear. Maintain a safe distance Anticipate traffic conditions for a smoother drive and to assure comfort and safety during your trip. Drive and maintain a safe distance from other vehicles while in traffic. This will help reduce fuel consumption as you will not be constantly tapping your brakes.

SECURITY INFORMATION SECURITY INFORMATION As owner of this vehicle important codes have been supplied to you that may be required by your NISSAN dealer to duplicate keys or re- Radio security code pair the radio. (where fitted) Please fill in the allocated areas or attach stick- er(s) if available. Remove this page and keep it in a safe place, not in the vehicle. When selling your vehicle, we kindly request Key number you to hand over this page to the buyer.

Wheel lock key code (where fitted)

Remove this page from the manual and keep it in a safe place, not in the vehicle. When selling your vehicle, we kindly request you to hand over this page to the buyer. Publication No.: OM10E-0M20E0E