MN002226A01_aa.fm Page 1 Wednesday, January 13, 2016 2:49 PM

wireless accessories may exceed the applicable RF Operational Cautions left, the radio chirps periodically or after releasing the PTT Monitor Button m exposure guidelines (iEEE, ICNIRP or FCC). Control Buttons button (Low Battery Alert). • For a list of Motorola-approved accessories for your radio Antennas ® Battery Capacity Maintenance Pressing and holding Scan/Monitor button for three TALKABOUT TWO-WAY RADIO model, visit the following website: http:// Do not use any portable radio that has a damaged antenna. seconds allows you to listen to the volume level of the radio T600 SERIES www.motorolasolutions.com/TalkaboutAccessories. If a damaged antenna comes into contact with your skin, a 1. Charge the NiMH batteries once every 3 months when not when you are not receiving. This allows you to adjust the minor burn can result. in use. Electromagnetic Interference/Compatibility volume, if necessary. You can also press Scan/Monitor Batteries 2. Before placing the radio in storage, remove the battery. Note: Nearly every electronic device is susceptible to 3. Batteries corrode over time and may cause permanent button to check for activity on the current channel before you All batteries can cause property damage and/or bodily injury talk. electromagnetic interference (EMI) if inadequately Accessory Port damage to your radio. such as burns if a conductive material touches exposed shielded, designed or otherwise configured for 4. Store the NiMH batteries in temperature between -20 °C to terminals. The conductive material may complete an electrical Push-to-Talk Timeout Timer electromagnetic compatibility. 35 °C and in low humidity. Avoid damp conditions and circuit (short circuit) and become hot. Emergency Button corrosive materials. To prevent accidental transmissions and save battery life, the This device complies with part 15 of the FCC Rules. Operation • Exercise care when removing NiMH or AA batteries. Do radio emits a continuous warning tone and stops transmitting if is subject to the following two conditions: not use sharp or conductive tools to remove these Using the Micro-USB Charger you press the PTT button for 60 continuous seconds. 1. This device may not cause harmful interference, and batteries. The micro-USB charger is a handy port that allows you to Mode Button 2. This device must accept any interference received, • Exercise care in handling any charged battery, particularly Flashlight Button including interference that may cause undesired when placing it inside a pocket, purse or other container conveniently charge your NiMH battery pack. operation. with metal objects. 1. Make sure your radio is turned OFF. By pressing “mode” button, the user will be seamlessly 2. Plug the micro-USB cable into the micro-USB charging switching between two-way and weather mode. When radio is in This device complies with Industry Canada licence-exempt RSS • Do not discard your battery in a fire. Push-to-Talk Screen standard(s). Operation is subject to the following two conditions: • Do not replace the battery in any area labeled “Hazardous (High) port on your radio. Connect the other end of the micro- two-way mode, will be shown. When radio is in USB charger to wall power outlet. 1. This device may not cause interference, and Atmosphere”. Any sparks created in a potentially weather mode, will be shown. Corresponding 2. This device must accept any interference received, explosive atmosphere can cause explosion or fire. Push-to-Talk (Low) Scan/Monitor 3. An empty battery will be fully charged in 8 hours. setting and information will be shown on the LCD. including interference that may cause undesired operation • Do not disassemble, crush, puncture, shred or otherwise 4. The battery meter on LCD will move to indicate the battery Mode Switch/Power Call Tone is charging. of the device. attempt to change the form of your battery. Menu Options Facilities • Do not dry a wet battery or damp battery with an appliance Volume/Scroll Note: or heat source, such as a hair dryer or microwave oven. Menu/Lock To avoid electromagnetic interference and/or compatibility • If the radio battery contact area has been submerged in • It is recommended to power OFF your radio while *MN002226A01* conflicts, turn off your radio in any facility where posted notices Mircrophone Micro-USB Charging charging. However, if power is turned on while charging, water, dry and clean the battery contacts before attaching Port Two Way Mode instruct you to do so. Hospitals or health care facilities may be the battery to the radio. you may not be able to transmit a message if the battery is MN002226A01-AA using equipment that is sensitive to external RF energy. Speaker completely empty. Allow time for the battery to charge to 1 Battery Charger Safety Instructions: Water Sensors bar before attempting to transmit a message. Aircraft Menu Button MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks • When moving between hot and cold temperatures, do not or registered trademarks of Motorola Trademark Holdings, LLC and are used under Save these Instructions When instructed to do so, turn off your radio when onboard an Channel (1-22) license. All other trademarks are the property of their respective owners. 1. Turn the radio off when charging the battery. Flashlight LED Water Sensors charge the NiMH battery pack until the battery © 2016 Motorola Solutions, Inc. All rights reserved. aircraft. Any use of a radio must be in accordance with Printed in China 2. Do not expose the charger to outside environment. temperature acclimates (usually about 20 minutes). Menu Button applicable regulations per airline crew instructions. • For optimal battery life, remove the radio from the charger Chargers should only be used indoors. Interference Eliminator Code (0-121) For More Information Medical Devices – Pacemakers, Defibrillators or other 3. Do not operate or disassemble the charger. Do not use a Display Screen Guide within 16 hours. Do not store the radio while connected to For further information, you may call Motorola Solutions at Implanted Medical Devices charger that has been dropped or damaged in any way. the charger. Menu Button 4. Never alter the AC cord or plug provided with the unit. If IVOX Call Tone (1-20) 1-800-448-6686 (Canada and U.S.), or visit us on the Internet at Persons with pacemakers, Implantable cardioverter- Attaching and Removing the Belt Clip the plug will not fit the outlet, have the proper outlet [OFF,L1,L2,L3] www.motorolasolutions.com/talkabout. defibrillators (ICDs) or other active implantable medical devices VOX [L1,L2,L3] Menu Button Menu Button installed by a qualified electrician. An improper condition Channel Battery (3 Battery 1. Attach the belt clip to the Talkabout plate at the back of the (AIMD) should: Hands Free (iVOX) (Off, L1,L2,L3) Safety and General Information can result in a risk of electric shock. Mode Levels) radio until the clip clicks in place. • Consult with their physicians regarding the potential risk of Mute 5. To reduce the risk of damage to the cord or plug, pull the Weather Alert Menu Button interference from radio frequency transmitters, such as 2. Attach the belt clip to pocket or belt strap until the clip plug rather than the cord when disconnecting the charger Power (High-Low) clicks in place. Dual Watch Channel (1-22) RF Exposure and Product Safety Instructions for portable radios (poorly shielded medical devices may be Roger Tone [On/Off] from the AC receptacle. Status (Transmit/ more susceptible to interference). Receive) To Remove Menu Button Portable Two-Way Radios General Populated and 6. To reduce the risk of electric shock, unplug the charger Keypad Tone [On/Off] Vibracall [On/Off] • Turn the radio OFF immediately if there is any reason to Dual Watch Interference Uncontrolled Environments. from the outlet before attempting any maintenance or Quiet Charge [On/Off] 1. Push the release tab on top of the belt clip to release the suspect that interference is taking place. Call Tone [number] cleaning. latch. Eliminator Code (1-121) • Do not carry the radio in a chest pocket or near the Dual Watch [On/Off] ATTENTION: 7. Use of an attachment not recommended or sold by FM Frequency Unit 2. Pull the belt clip away from the back of the radio. Menu Button implantation site, and carry or use the radio on the Before using this radio, refer to the important operating Motorola Solutions may result in a risk of fire, electric Scan opposite side of their body from the implantable device to Code Turning your Radio On and Off VibraCall Alert (On/Off) instructions for safe usage and RF energy awareness and shock or personal injury. Keypad Lock Number (used for Call minimize the potential for interference. Tone and Speaker Volume) Menu Button control for compliance with applicable Standards and 8. Make sure the cord is located so it will not be stepped on, MODE On/Off Press and hold the Mode Switch/Power button to turn the Regulations. Hearing Aids tripped over or subjected to damage or stress. Keypad Tones (On/Off) L0/L2/L2/L3 (used for VOX and Battery radio On or Off. 9. An extension cord should not be used unless absolutely Save) Some digital wireless radios may interfere with some hearing 1. In the ON position, the radio chirps and briefly shows all Menu Button Compliance with RF Exposure Standards necessary. Use of an improper extension cord could result FM Frequency 87.5 - 108.0 MHz aids. In the event of such interference, you may want to consult feature icons available on the radio. Talk Confirmation Tones (On/Off) in a risk of a fire and/or electric shock. If an extension cord Your Motorola Two-Way radio complies with the following RF your hearing aid manufacturer to discuss alternatives. 2. The display screen then shows the current channel, code energy exposure standard and guidelines: must be used, make sure that: Getting Started Other Medical Devices and all features that are enabled. The radio is now in Two Way Mode • United States Federal Communications Commission, • The pins on the plug of the extension cord are the same If you use any other personal medical device, consult the Two-Way mode. Code of Federal Regulations; 47 CFR et seq. & FCC. number, size and shape as those on the plug of the Waterproof • Institute of Electrical and Electronic Engineers (IEEE) manufacturer of your device to determine if it is adequately charger. shielded from RF energy. Your physician may be able to assist • The extension cord is properly wired and in good C95.1. This radio is waterproof to IP-67 standards. It will withstand Mode Button • International Commission on Non-Ionizing Radiation you in obtaining this information. condition. submersion under up to 1 meter of water for up to 30 minutes. Setting the Volume Protection (ICNIRP).e Use of Communication Devices While Driving • The extension cord size is 18 AWG for lengths up to 100 The radio is resistant to water, rain, and splashes only when the Weather Mode feet, and 16 AWG for lengths up to 150 feet. From any mode, by first press on either or it will trigger • Ministry of Health (Canada) Safety Code 6 & Industry Always check the laws and regulations on the use of radios in battery cover and headset accessory port are sealed. Open the 10. The supply cord of the AC adaptor cannot be replaced. If volume changing and showing the current value. Menu Button Canada RSS-102. the areas where you drive. battery compartment door or headset port cover only when the the cord is damaged, call customer service. radio is dry. Use of a headset accessory should be in dry • Australian Communications Authority • Give full attention to driving and to the road. 1. Press to increase the speaker volume. Weather Channel (1-11) Menu Button Radiocommunications Standard et seq. environments only. • Use hands-free operation, if available. FCC Licensing Information 2. Press to decrease the speaker volume. • ANATEL ANNEX to Resolution No. 303 of July 2, 2002. • Pull off the road and park before making or answering a The charging base and AC adaptor are not waterproof. Do not Menu Button • ANATEL ANNEX to Resolution No. 533 of September 10, expose the charger to rain or snow. Charge the radios only in a Do not hold the radio close to your ear. If the volume is set to an call, if driving conditions or regulations so require. Your Motorola Solutions radio operates on General Mobile Weather Alert (On/Off) 2009. dry location. Do not place wet radios into the charging base. uncomfortable level, it could hurt your ear. For Vehicle With Air Bags Radio Service (GMRS) frequencies and is subject to the Rules and Regulations of the Federal Communications Commission Transmit and Receive Procedure Refer to the vehicle manufacturer’s manual prior to installation WARNING: This radio floats with the included NiMH battery Talking and Listening Selecting the Channel (FCC). of electronic equipment to avoid interference with air bag wiring. (800mAh). It may not float with other batteries. Your two-way radio contains a transmitter and a receiver. To The FCC requires that all operators using GMRS frequencies To communicate, all radios in your group must be set to the Your radio has 22 channels. The channel is the frequency the Do not place a portable radio in the area over an air bag or in control your exposure and ensure compliance with the general obtain a radio license before operating their equipment. To Installing the Batteries same channel and Interference Eliminator Code. radio uses to transmit. Channels 8-14 are FRS 0.5 watt only and the air bag deployment area. Air bags inflate with great force. If population/uncontrolled environment exposure limits, always obtain the FCC forms, please visit the FCC website at 1. To talk, press and hold the PTT button. When transmitting, all other channels are GMRS. (See the “Channels and a portable radio is placed in the air bag deployment area and the Each radio can use either 1 NiMH rechargeable battery pack or adhere to the following procedure: wireless.fcc.gov/uls/index.htm?job=home to source form 605 Frequencies” table on overleaf for details). air bag inflates, the radio may be propelled with great force and 3 AA alkaline batteries and beeps when the batteries are low. icon blinks and is shown. If it is a high • Transmit no more than 50% of the time. and 159, which includes all the instructions you will need. cause serious injury to occupants of the vehicle. 1. With the radio on, press Menu/Lock button until the • To receive calls, release the PTT button. If you wish to have the document faxed or mailed, or if you have power transmission, is shown. If it is a low power Installing the NiMH Rechargeable Battery Pack channel number starts to flash. When the radio is on a 0.5 • To transmit (talk), press the Push-to-Talk (PTT) button in Potentially Explosive Atmosphere questions, please use the following contact information: transmission, is shown. front of the face. 1. Turn the radio off. 2. When you are finished talking, release the PTT button. watt channel, display shows . When the radio is on a • Hold the radio in a vertical position with the microphone Turn off your radio prior to entering any area with a potentially For a fax: For mail service: If you have questions 2. With the back of the radio facing you, loosen the retaining (and other parts of the radio including the antenna) at least explosive atmosphere. Only radio types that are especially Contact the Fax-On- Call the FCC Forms about the FCC License: screw on the battery door and open the cover. 3. When receiving, icon blinks and is 1.5 watts channel, display shows . The current channel Demand system Hotline Call the FCC one inch (2.5 centimeters) away from the nose or lips. qualified should be used in such areas as “Intrinsically Safe”. Do 3. Remove the NiMH battery pack from the clear plastic bag shown. If it is a high power channel, is shown. If it is a flashes. 1-888-CALL-FCC Keeping the radio at a proper distance is important to not remove, install or charge batteries in such areas. Sparks in a 1-202-418-0177 1-800-418-FORM (3676) (do not disassemble or unwrap the battery pack). low power channel, is shown. 2. Press or and select an unused or quiet channel. ensure compliance. potentially explosive atmosphere can cause an explosion or fire (225-5322) 4. Insert the NiMH battery pack with the diagram facing you. For maximum clarity, hold the radio two to three inches away resulting in bodily injury or even death. (The ribbon should be underneath the battery pack and 3. Press the PTT button to save the channel setting or Note: RF exposure decreases with increasing distance from the Changes or modifications not expressly approved by Motorola from your mouth and speak directly into the microphone. Do not should wrap around the right side of the pack for easy Menu/Lock button to continue set up. antenna. Note:The areas with potentially explosive atmosphere referred Solutions may void the user authority granted by the FCC to cover the microphone while talking. removal). to above include fueling areas such as below decks on operate this radio and should not be made. To comply with FCC • Body Worn Operation. When worn on the body, always 5. Close the battery cover and tighten the retaining screw on Talk Range boats, fuel or chemical transfer or storage facilities, areas requirements, transmitter adjustments should be made only by place the radio in a Motorola-approved clip, holder, the battery cover. where the air contains chemicals or particles (such as or under the supervision of a person certified as technically holster, case or body harness for this product. Your radio is designed to maximize performance and improve grain, dust or metal powders) and any other area where qualified to perform transmitter maintenance and repairs in the Please refer to the following websites for more information on Installing the Three AA Alkaline Batteries transmission range. Do not use the radios closer than five feet you would normally be advised to turn off your vehicle private land mobile and fixed services as certified by an what RF energy exposure is and how to control your exposure apart. engine. Areas with potentially explosive atmospheres are organization representative of the user of those services. 1. Turn the radio off. to assure compliance with established RF exposure limits: often – but not always posted. Replacement of any transmitter component (crystal, 2. With the back of the radio facing you, lift the battery cover Power Boost • http://www.fcc.gov/oet/rfsafety/rf-faqs.html semiconductor, etc) not authorized by the FCC equipment latch up and remove the cover. • www.who.int/en/ Blasting Caps and Areas authorization for this radio could violate FCC rules. 3. Insert the three AA Alkaline batteries with + and – polarity To boost the power of your radio to high power, press the top • http://responsibility.motorolasolutions.com/index.php/ as shown inside. (The ribbon should be underneath the portion of the PTT button when talking. If you know your party is To avoid possible interference with blasting operations, turn off Note: Use of this radio outside the country where it was downloads/dow07-rfexposureassessmentstand/ AA alkaline batteries and should wrap around the right close by, you can conserve the energy of your battery by your radio when you are near electrical blasting caps, in a intended to be distributed is subject to government side of the batteries). pushing the lower part of the PTT button to use less power. blasting area, or in areas posted “Turn off two-way radios”. Obey regulations and may be prohibited. 4. Close the battery cover and tighten the retaining screw on Two-way Radio Operation all signs and instructions. Note: If you are on an FRS only channel (see “Channels and the battery cover. Frequencies”) the radio will only use low power when • Use only Motorola-approved supplied or replacement Radio Battery Meter either portion of the PTT button is pressed. antennas, batteries, and audio accessories. Use of non- Motorola-approved antennas, batteries, and wired or The radio battery icon shows the battery charge level, from full to empty . When the radio has one segment MN002226A01_aa.fm Page 2 Wednesday, January 13, 2016 2:49 PM

There is a priority feature and 2 modes of scanning (basic and States or Canada, which are accompanied by this written For Accessories: Selecting the Interference Eliminator Code 1. With the radio on, press Menu/Lock button until the Entering Weather Mode advanced) to make your search more effective. The basic scan warranty: Please call the telephone number designated above for the Interference Eliminator Codes help minimize interference by appears. The current setting On/Off flashes. mode uses the channel and code combinations for each of the MODE Product with which they are used. blocking transmissions from unknown sources. Your radio has 22 channels as you have set them (or with the default code 1. From two-way mode, press Mode Switch/Power Who is Covered? 121 Interference Eliminator Codes. Codes 1 – 38 are standard 2. Press or to turn On or Off. value of 1). The “Advanced Scan” mode will scan all channels button to enter weather mode . This warranty extends only to the first consumer purchaser, and You will receive instructions on how to ship the Products or analog codes that appear on other FRS/GMRS radios. Codes 3. Press the PTT button to set or to continue set up. for any and all codes, detect any code in use and use that code is not transferable. Accessories at your expense, to Motorola or a Motorola 39 – 121 are additional digital codes added for superior value temporarily for that channel. Setting the Weather Channel Authorized Repair Center. To obtain service, you must include: interference protection. 0 is the off position, no analog or digital Priority is given to the “home channel”, that is, the channel (and What will MOTOROLA SOLUTIONS, INC. do? (a) a copy of your receipt, bill of sale or other comparable proof Your radio receives weather frequencies: codes are enabled. Dual Watch Mode Interference Eliminator Code) your radio is set to when you start of purchase; (b) a written description of the problem; (c) the Motorola Solutions, Inc., at its option, will at no charge repair, the scan. This means the initial channel (and code settings) is 1. In weather mode, press Menu/Lock button until name of your service provider, if applicable; (d) the name and To set the code for a channel: Enables you to scan the current channel and another channel replace or refund the purchase price of any Products or scanned more often than the other 21 channels and your radio weather channel number flashes. location of the installation facility (if applicable) and, most alternately. Accessories that do not conform to this warranty. We may use 1. Press Menu/Lock button until the code starts to flash. will respond quickly to any activity occurring on the home importantly; (e) your address and telephone number. 2. Press or to select the appropriate channel with functionally equivalent reconditioned/ refurbished/ pre-owned or To set another channel and start Dual Watch. channel as a priority. 2. Press or to select the code. good reception in your area. new Products or Accessories. For more information, please visit us at: 1. Press Menu/Lock until appears. The current call To start Scanning: 3. Press the PTT button to save the code setting or 3. Press the PTT button to set or Menu/Lock button to What Other Limitations Are There? Menu/Lock button to continue set up. tone setting will flash. continue set up weather alert. https://www.facebook.com/ You can set a different code for each channel using this 1. Briefly press the Scan/Monitor button. The scan Any Implied Warranties, Including Without Limitation MotorolaTalkaboutWalkieTalkies 2. Press or to select the channel, then press . will appear in the display and the radio will begin to scroll Setting the Weather Alert procedure. An extended press of or allows you to scroll The implied warranties of merchantability and fitness for a 3. Press or to select the code. through the channel and code combinations. particular purpose, shall be limited to the duration of this limited through the Interference Code rapidly so you can quickly reach 2. When the radio detects channel activity matching the Your radio can be set to respond to NOAA Weather Radio 4. Press the PTT button to save the channel setting or warranty, otherwise the repair, replacement, or refund as the code you want. channel and code combination, it stops scrolling and you emergency messages. A special alarm tone sounds an alert and http://bit.ly/Talkabout Menu/Lock button to continue set up. provided under this express limited warranty is the exclusive can hear the transmission. turns on the weather receiver to give you immediate weather Note: On a radio that uses Interference Eliminator Codes, the 5. The radio starts to Dual Watch. and emergency information. remedy of the consumers, and is provided in lieu of all other code must be set to 0 to communicate with radios that do 3. To respond and talk to the person transmitting, press the warranties, express or implied. In no event shall Motorola not have Interference Eliminator Codes. Select 0 for “no Special Features PTT button within five seconds after the end of the 1. In weather mode press Menu/Lock button twice until Solutions be liable, whether in contract or tort (including www.motorolasolutions.com/talkabout tone, no code” on the display of your radio. transmission. displays. negligence) for damages in excess of the purchase price of the 4. The radio will resume scrolling through the channels five 2. Press or to select On/Off. product or accessory, or for any indirect, incidental, special or Emergency Alert Mode seconds after the end of any received activity. 3. Press the PTT button or Menu/Lock button to exit the consequential damages of any kind, or loss of revenue or www.motorolasolutions.com/talkabout/pt Setting and Transmitting Call profits, loss of business, loss of information or other financial (Portuguese) The Emergency Alert feature can be used to signal members in 5. To stop scanning, briefly press the Scan/Monitor weather menu set up. your group of your need for urgent help. T6XX series radios will button. loss arising out of or in connection with the ability or inability to Tones MODE operate in an automatic “hands-free” emergency control mode 4. Press Mode Switch/Power button to return to two-way use the products or accessories to the full extent these To start Advanced Scanning www.motorolasolutions.com/talkabout/es Your radio can transmit different call tones to other radios in for a total of 30 seconds after activating the Emergency Alert. mode. If you activate Weather Alert and return to two-way damages may be disclaimed by law. (Spanish) your group so you can alert them that you want to talk. Your T6XX series radios in your group will automatically advance the 1. Set the Interference Eliminator Code to “zero” or OFF. mode will display. radio has 20 call tones from which to choose. speaker volume to the maximum setting and sound a warbling Some states and jurisdictions do not allow the limitation or 2. Briefly press the Scan/Monitor button. The scan Note:When the weather channel is activated, either manually or exclusion of incidental or consequential damages, or limitation To set a call tone: alert tone for 8 seconds. The alert tone is emitted from your own will appear in the display and the radio will begin to scroll radio speaker and the receiving radios in your group. After the 8 after receiving an alert, and no buttons are pressed for 5 on the length of an implied warranty, so the above limitations or through the channels. No Interference Eliminator Codes minutes, the weather mode will automatically revert back 1. Press Menu/Lock until appears. The current call second alert, any spoken words or incidental sounds at your end exclusions may not apply to you. This warranty gives you will filter what is heard. to two-way mode. specific legal rights, and you may also have other rights that tone setting will flash. will be transmitted to the group for 22 seconds. For the 30 3. When the radio detects channel activity with ANY code (or second duration of Emergency Alert mode, T6XX series radio vary from state to state or from one jurisdiction to another. 2. Press or to change and hear the call tone. NO code), it stops scrolling and you can hear the As with two-way radio reception, weather channel reception controls and buttons will be locked to maximize reception of the transmission. Any Interference Eliminator Code that may depends on how close you are to a transmitter and whether you Products Covered Length Of Coverage 3. Press the PTT button to set the new call tone or emergency message. be in use by that party will be detected and displayed. are indoors or outdoors. Because weather channels are Menu/Lock button to continue set up. 1. Press and hold the Emergency Alert button for 3 seconds. transmitted without codes, they may contain static or noise. Products and 4. To respond and talk to the person transmitting, press the Accessories To transmit your call tone to other radios set up to the same 2. Release the button the alert tone begins to sound. There PTT button within five seconds of the end of the Weather Alert will not function while actively transmitting or channel and Interference Eliminator Code as your radio, press is no need to continue to hold the Emergency Alert button receiving in two-way mode. as defined above, unless transmission. The radio will transmit using the newly otherwise provided for Call Tone button. or use PTT for your message to be transmitted. detected Interference Eliminator Code. One (1) year from the date of 3. After the alert tone ends you may speak into the below: purchase by the first consumer Note: Setting the call tone to 0 disables the call tone feature. 5. The radio will resume scrolling through the channels five microphone. Your voice or incidental sounds will be seconds after the end of any received activity. Weather Channels and Frequencies Batteries purchaser of the product unless Voice Operated Transmission ( ) transmitted. whose fully charged otherwise provided for below. 4. After 30 seconds your radio speaker will emit a Talk 6. To stop scanning, briefly press the Scan/Monitor capacity falls below 80% of Weather Channel Frequency Weather Channel Frequency Transmission is initiated by speaking into the microphone of the Confirmation Tone. Operation then returns to normal button. their rated capacity and two-way mode. WX1 162.550 MHz WX7 162.525 MHz radio instead of pushing the PTT button. Scanning Notes: batteries that leak 1. Press Menu/Lock button until appears. The Note: All Motorola Talkabout EM, MJ, MR, MT, MU, T4XX and WX2 162.400 MHz WX8 161.650 MHz Products and The balance of the original current setting T6XX series radios (except for model T400) are fully 1. If you press the PTT button while the radio is scrolling WX3 162.475 MHz WX9 161.775 MHz Accessories warranty or for ninety (90) days (L1 – L3) will flash. compatible with the Emergency Alert feature. Radios through inactive channels, the transmission will be on the WX4 162.425 MHz WX10 161.750 MHz that are repaired or from the date returned to the other than EM, MJ and MR series can receive the “home channel”. Scanning will resume five seconds after WX5 162.450 MHz WX11 162.000 MHz replaced consumer, whichever is longer. 2. Press or to select the sensitivity level. the end of your transmission. You may press the emergency alert signal, but will not respond with adjusted WX6 162.500 MHz 3. Press the PTT button to set or Menu/Lock button to volume settings, locked controls or a warbling alert tone. Scan/Monitor button to stop scanning at any time. continue set up. Exclusions From Warranty Coverage Users of other radio models set to the same channel and 2. If the radio stops on an undesired transmission, you may Channels and Frequencies Interference Eliminator Code will hear a steady tone for 8 Normal Wear and Tear: L3 = High Sensitivity for quiet environments seconds followed by the voice transmission for 22 immediately resume the scan by briefly pressing or Periodic maintenance, repair and replacement of Products or L2 = Medium Sensitivity for most environments USA, Canada, Mexico, Panama, Uruguay seconds. Accessories due to normal wear and tear. L1 = Low Sensitivity for noisy environments . 3. If the radio repeatedly stops on an undesired Channel Frequency Description Channel Frequency Description WARNING: The Emergency Alert feature should only be transmission, you may temporarily remove that channel 1 462.5625 MHz GMRS/FRS 12 467.6625 MHz FRS Abuse & Misuse: Note:There is a short delay between the time you start talking Defects or damage that result from: (a) improper operation, used in the event of an actual emergency. from the scan list by pressing and holding or for 2 462.5875 MHz GMRS/FRS 13 467.6875 MHz FRS and when the radio transmits. There is a short delay Motorola Solutions is not responsible if there is storage, misuse or abuse, accident or neglect, such as three seconds. You may remove more than one channel in 3 462.6125 MHz GMRS/FRS 14 467.7125 MHz FRS before the transmission is completed. no response to the emergency alert from the physical damage (cracks, scratches, etc.) to the surface of the this way. 4 462.6375 MHz GMRS/FRS 15 462.5500 MHz GMRS Products and Accessories resulting from misuse; (b) contact receiving group. 4. To restore the removed channel(s) to the scan list, turn the TM 5 462.6625 MHz GMRS/FRS 16 462.5750 MHz GMRS with liquid, water, rain, extreme humidity or heavy perspiration, VibraCall Alert radio off and then turn back on, or exit and re-enter the Built-in LED Flashlight 6 462.6875 MHz GMRS/FRS 17 462.6000 MHz GMRS sand, dirt or the like, extreme heat, or food; (c) use of the TM scanning mode by pressing Scan/Monitor button. Products or Accessories for commercial purposes or VibraCall is a vibrating alert that notifies you that your radio is Press the Flashlight button to cycle between OFF, RED Light, 7 462.7125 MHz GMRS/FRS 18 462.6250 MHz GMRS 5. You cannot remove the home channel from the scan list. subjecting the Product or Accessory to abnormal usage or receiving a message. This is useful in noisy environments. WHITE Light and then back to OFF again. 8 467.5625 MHz FRS 19 462.6500 MHz GMRS 6. In Advanced Scan, the detected code will only be used for conditions; or (d) other acts which are not the fault of Motorola. When the alert is on, the radio vibrates once every 30 seconds The Flashlight will turn off when you press the Flashlight button one transmission. You must note that code, exit scan and 9 467.5875 MHz FRS 20 462.6750 MHz GMRS when you receive a message on the channel and code you set. if the RED Light is left on for more than 3 seconds. set that detected code on that channel to permanently use 10 467.6125 MHz FRS 21 462.7000 MHz GMRS Use of Non-Motorola branded Products and Accessories: The Flashlight will turn off automatically after 30 minutes of non- 1. To turn vibrating alerts on, press Menu/Lock button the detected code. 11 467.6375 MHz FRS 22 462.7250 MHz GMRS Defects or damage that result from the use of Non-Motorola activity if the battery level is below 50%. branded or certified products, accessories, software or other until is displayed. The current setting will flash. Note: Turn off the flashlight when not in use to conserve battery peripheral equipment. 2. Press or to change the setting to On/Off. power. Weather Receiver Unauthorized Service or Modification: 3. Press the PTT button to confirm or Menu/Lock button Water Sensor Your radio can tune in to broadcasts by the United States Patent and Copyright Information Defects or damages resulting from service, testing, to continue set up. adjustment, installation, maintenance, alteration, or When your radio is dropped into water, the WHITE LED National Oceanic and Atmospheric Administration (NOAA) MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the modification in any way by someone other than Motorola or its Keypad Tones flashlight will be activated to help you locate and retrieve your Weather Radio and Environment Canada Weather Radio. Stylized M logo are trademarks or registered trademarks of authorized service centers. radio. You can listen to a weather channel (see “Weather Channels You may enable or disable the speaker key tones. You will hear Motorola Trademark Holdings, LLC and are used under license. The water sensors are located near the base of the radio. It may and Frequencies” table for details) or set your radio to alert you the key tone each time a button is pushed. All other trademarks are the property of their respective owners. Altered Products: accidentally trigger the WHITE LED if you place your radio on a to emergency weather broadcasts that interrupt routine © 2016 Motorola Solutions, Inc. All rights reserved. Products or Accessories with (a) serial numbers or date tags 1. Press Menu/Lock button until appears. The current wet surface. Keep the sensors dry and press the torch light broadcasts. When you listen to a weather channel, you cannot that have been removed, altered or obliterated; (b) broken setting On/Off will flash. button to reset and turn off the flashlight. use your radio in scan mode or for two-way communications. Warranty seals or that show evidence of tampering; (c) mismatched 2. Press either or to turn On or Off. Both NOAA and Environment Canada have transmitters located Keypad Lock throughout the United States and Canada, respectively. These board serial numbers; or (d) nonconforming or non-Motorola branded housings, or parts. 3. Press the PTT button to confirm or Menu/Lock button To avoid accidentally changing your radio settings: transmitters broadcast watches, forecasts and other information Consumer Two-Way Radio Products and to continue set up. 24 hours a day. Accessories purchased in the United States or Communication Services: Note: When the key tone feature is off, the following are not 1. Press and hold Menu/Lock button until displays. Note: NOAA weather radio stations are assigned to cover Canada Defects, damages, or the failure of Products or Accessories disabled: 2. When in lock mode, you can turn the radio on and off, specific areas and service may be limited. Please check due to any communication service or signal you may subscribe adjust the volume, receive, transmit, send a call tone and with your local weather office for frequency and details or What Does this Warranty Cover? • Transmit timeout alert tone to or use with the Products or Accessories. monitor channels. All other functions are locked. visit www.weather.gov/nwr in the US to view the • Call tone Subject to the exclusions contained below, Motorola Solutions, appropriate transmitter for your area. The use of the How to Obtain Warranty Service or Other • Low battery alert tone or 3. To unlock the radio, press and hold Menu/Lock button Inc. (“Motorola”) warrants the Motorola branded consumer NOAA logo does not provide an endorsement or implied • The transmitted talk confirmation tone two-way radios that operate via Family Radio Service or Information? until is no longer displayed. endorsement by the National Weather Service of NOAA, General Mobile Radio Service (“Products”), the Motorola Transmitting a Talk Confirmation Tone nor does the use of the Weatheradio logo provide an To obtain service or information, please call Scanning Channels branded or certified accessories sold for use with these endorsement or implied endorsement by Environment Products (“Accessories”) to be free from defects in materials You can set your radio to transmit a unique tone when you finish USA and Canada Two-Way Radios Use scan to search the 22 channels for transmissions from Canada. and workmanship under normal consumer usage for the transmitting. It is like saying “Roger” or “Over” to let others know 1-800-448-6686. unknown parties, to find someone in your group who has period(s) outlined below. This limited warranty is the exclusive you are finished talking. www.motorolasolutions.com/talkabout accidentally changed channels or to quickly find unused remedy of a consumer, and applies as follows to new Products channels for your own use. and Accessories and purchased by consumers in the United