also aVaiabJ
SYSTEM ERROR MESSAGES
Cisco INTERNEFWORK OPERATING SYSTEM
Release 11.2
Cisco SYSTEMS SCaR
System Error Messages
Cisco Internetwork Operating System Release 11.2
Corporate Headquarters Cisco Systems Inc 170 West Tasman Drive San Jose CA 951 34-1 706 USA World Wide Web UFIL
http//www.cisco.com Tel 408 526-4000 800 553-NETS 6387 Fax 408 526-4100
Customer Order Number DOC-SYSEM1 1.2
Text Part Number 78-3417-01 THE SPECIFICATIONS J4D O1tJTIoN RECJAJWING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE ALL STATEMENTS AND INFORMATION RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND EXPRESS OR IMPLIED USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS
SOFTWARE LICENSE
PLEASE READ THESE TERMS AND CONDITIONS CAREFULLY BEFORE USING THE SOFTWARE BY USING THIS SOFTWARE YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THIS LICENSE IF YOU DO NOT AGREE WITH THE TERMS OF THIS LICENSE PROMPTLY RETURN THE UNUSED SOFTWARE MANUAL AND RELATED EQUIPMENT AND HARDWARE WITH PROOF OF PAYMENT TO THE PLACE OF PURCHASE FOR FULL REFUND
Cisco Inc Systems Cisco and its suppliers grant to Customer nonexciusive and Customer nontransferable license to use the Cisco software in code form Software object solely on single central processing unit owned or leased Customer otherwise by or embedded in equipment provided by Cisco Customer make one archival of the may copy software provided Customer affixes to such all copy copyright confidentiality and proprietary notices that appear on the original EXCEPT AS EXPRESSLY AUTHORIZED ABOVE CUSTOMER SHALL NOT COPY IN WHOLE OR IN PART SOFTWARE OR DOCUMENTATION MODIFY THE SOFTWARE REVERSE COMPILE OR REVERSE ASSEMBLE ALL OR ANY PORTiON OF THE SOFTWARE OR RENT LEASE DISTRIBUTE SELL OR CREATE DER1VATIVE WORKS OF THE SOFTWARE
Customer agrees that aspects of the licensed materials the and including specific design structare of individual programs constitute trade secrets and/or material of Cisco copyrighted Customer agrees not to disclose provide or othenvise make available such trade secrets or copyrighted material in any form to any third without the written of party prior consent Cisco Customer to reasonable agrees implement security measures to protect such trade secrets and copyrighted material Title to Software and documentation shall remain solely with Cisco
This License is effective until terminated Customer terminate this License at time may any by destroying all copies of Software including any documentation This License will terminate without immediately notice from Cisco if Customer fails to with comply any provision of this License Upon termination Customer must destroy all copies of Software --
Software including technical data is subject to U.S control the U.S export laws including Export Administration Act and its associated regulations and be may subject to export or import regalations in other countries Customer agrees to comply strictly with all such and regulations acknowledges that it has the to obtain responsibility licenses to export re-export or Import Software
This License shall be and governed by construed in accordance with the laws of tbe State of United States California of America as if performed wholly within the state and without effect to the of giving principles conflict of law If hereof is found be any portion to void or unenforceable the remaining of this provisions License shall remain in full force and effect This License constitutes the entire License between the parties with respect to the use of the Software
Restricted Ciscos software is Rights provided to non-DOD agencies with RESTRICTED RIGHTS and its supporting documentation is provided with LIMITED RIGHTS Use duplication or disclosure by the Government is to the restrictions subject as set forth in subparagraph of the Commercial Computer Software Restricted clause at FAR Rights 52227-19 In the event the sale is to DOD the agency governments rights in software supporting documentation and technical data are the restrictions in the governed by Technical Data Commercial Items clause at DFARS 252.227-7015 and DFARS 227.7202
LIMITED WARRANTY
Software Cisco warrants that for period of from the date of ninety 90 days shipment from Cisco the media on which the Software is furnished will be free of defects in materials and workmanship under normal use and the Software ii substantially conforms to its published specifications Except for the foregoing the Software is provided AS IS This limited warranty extends only to Customer as the licensee original Customers exclusive remedy and the entire liability of Cisco and its suppliers under this limited will Cisco warranty be at or its service centers option repair replacement or refund of the Software if reported or upon request returned to the party supplying the Software to Customer In no event does Cisco warrant that the Software is error free or that Customer will be able to the operate Software without problems or interruptions
Hardware Cisco that for warrants period of ninety days from the date of from Cisco the 90 shipment Hardware wilt be free from defects in material and under workijianship normal uses This limited warranty extends to Customer as the only original purchaser Customers exclusive remedy and the entire of Cisco and its under this liability suppliers limited will he at Ciscos or its service warranty centers option shipment of an advance replacement within five working days at Ciscos or refund of the expense purchase price if the Hardware is returned to the party supplying it to Customer freight and insurance prepaid Cisco in replacement parts used Hardware repair may be new or equivalent to new
Restrictions This warranty does not apply if the has been product altered except by Ciseo has not been installed operated repaired or maintained in accordance with instructions supplied by Cisco has been subjected to abnormal or electrical physical stress misuse negligence or accident or is used in ultrahazardous activities ALL EXPRESS OR IMPLIED CONDITIONS DISCLAiMER OF WARRANTY EXCEPT AS SPECIFIED IN THIS WARRANTY ANY IMPLIED WARRANTY OF MERCHANTABILiTY REPRESENTATIONS AND WARRANTIES INCLUDING WITHOUT LIMITATION FROM COURSE OF DEALING USAGE OR TRADE FITNESS FOR PARTICULAR PURPOSE NONThTFRINGEMENT OR ARISING BY APPLICABLE LAW PRACTICE ARE HEREBY EXCLUDED TO THE EXTENT ALLOWED
FOR ANY LOST REVENuE PROFIT OR DATA OR FOR SPECIAL INDIRECT IN NO EVENT WILL CISCO OR ITS SUPPLIERS BE LIABLE CAUSED AND REGARDLESS OF THE THEORY OF LIABILiTY CONSEQUENTIAL INCIDENTAL OR PUNITIVE DAMAGES HOWEVER ADVISED OF THE EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ARISING OUT OF THE USE OF ORINABILITY TO USE THE PRODUCT whether in contract tort including negligence or Ciscos its to Customer POSSIBILITY OF SUCH DAMAGES In no event shall or suppliers liability fails of its essential The limitations shall apply even if the above-stated warranty purpose otherwise exceed the price paid by Customer foregoing
tested and found to with the limits for Class of Class devices This equipment has been comply The following information is for FCC compliance interference when the to reasonable protection against harmful to 15 nf the FCC rules These limits are designed provide digital device pursuant part radiate and if not installed and used commercial environment This equipment generates uses and can radio-frequency energy equipment is operated in is of this in residential area harmful interference to radio communications Operation equipment in accordance with the instruction manual may cause interference at their own interference in-which case users will he required to correct the expense likely to cause harmful
manual and radiate radio-frequency FCC of Class devices The equipment described in this generates may The following information is for compliance radio and television reception This equipment it cause interference with installed in accordance with Ciseos installation instructions may energy If it is not in 15 of the FCC rules These limits for Class device in accordance with the specifications part has been tested and found to comply with the digital there is no that in residential installation However guarantee to reasonable protection against such interference specifications are designed provide
interference will not occur in particular installation
caused the Cisco off If the interference it was probably by equipment is interference turning it stops You can determine whether your equipment causing hy interference one or more of to correct the by using interference to radio or television reception try or one of its peripheral devices If the equipment causes
the following measures
interference Turn the television or radio antenna until the stops
other of the television or radio Move the equipment to one side or the
from the television or radio Move the equipment farther away
television or radio radio is make certain the equipment and the outlet that is on different circuit from the television or That Plug the equipment into an circuit breakers or fuses are on circuits controlled by different
to the Inc could void the FCC approval and negate your authority operate product Modifications to this product not authorized by Cisco Systems
the software license he included with product and will be subject to agreement The following third-party software may your
license from the Hewlett-Packard HP is based in on HP under Company OpenView CiscoWorks software and documentation are part OpenView 1993 Hewlett-Packard Company trademark of the Hewlett-Packard Company Copyright 1992
as of the of California Berkeley UCB part of TCP header is an adaptation of program developed by University The Cisco implementation compression reserved of the University of California UNIX All rights Copyright 1981 Regents UCBs public domain version of the operating system
about the of this David Mills The University of Delaware makes no representations suitability Network Time Protocol NTP Copyright 1992
software for any purpose
endorse or All reserved The name of the University may not be used to Point-to-Point Protocol Copyright 1989 Carnegie-Mellon University rights written derived from this software without specific prior permission promote products
and developed by the University of California Berkeley is of the TN3270 curses termcap programs The Cisco implementation of TN3270 an adaptation of All reserved 1981-1988 Regents of the Uriversity domain version of the UNIX operating system rights Copyright UCB as part of UCBs public
California
Token Fastmac software is licensed to Cisco by Madge and TrueView software and the RingRunner chip in some Ring products Cisco incorporates Fastmac and TrueView are trademarks and in some is licensed to Cisco NV Fastmae RingRunner Networks Limited and the RingRunner chip by Madge Limited All reserved of Networks Limited Copyright 1995 Madge Networks rights jurisdictions registered trademarks Madge
Mountain View California NCD Inc 1989 Network Computing Devices Inc XRemote is trademark of Network Computing Devices Copyright
the of this software for makes no representations about suitability any purpose
TABLE OF CONTENTS
About This Manual xv
How This Manual Is Organized xv
How to Read System Error Messages xvi
Error Message Traceback Reports xxiv
System Error Messages
AAA Accounting Messages
AlP Error Messages
ALIGN Error Messages
APPNError Messages
ARAP Error Messages
AT Error Messages 11
ATM Error Messages 32
BGP Error Messages 34
BRI Error Messages 36
BSC Error Messages 37
BSTUN Error Messages 38
CBUS Error Messages 43
CCP Error Message 59
CI Error Messages 59
CLEAR Error Message 63
CLNS Error Messages 63
CLS Error Message 69
CLSDR Error Messages 69
COMP Error Messages 72
Table of Contents CONTROLLER Error Messages 74
CSC2 Error Message 75
DRUS Error Messages 75
DIALER Error Messages 81
DIRRESP Error Message 81
DLC Error Messages 82
DLSw Error Messages 84
DMA Error Messages 89
DNET Error Messages 91
DNSIX Error Message 92
DRP Error Message 92
DSPU Error Messages 93
DSX1 Error Messages 100
DUAL Error Messages 100
DVMRP Error Messages 106
EGP Error Messages 106
ENV Error Messages 107
ENVM Error Messages 108
ETHERNET Error Messages 110
FDDI Error Messages 110
FDDISTAT Error Message 112
FILESYS Error Messages 113
FLASH Error Messages 113
FR Error Messages 114
GRIP Error Messages 115
vi System Error Messages HD Error Messages 115
HUB Error Messages 118
1BM2692 Error Messages 119
IGRP Error Message 121
If Error Messages 121
IPC Error Messages 124
JPFAST Error Messages 128
IPRT Error Messages 131
IPX Error Messages 132
ISDN Error Messages 134
LANCE Error Messages 134
LANE Error Messages 137
LANMGR Error Messages 149
LAPB Error Messages 150
LAT Error Messages 152
LEX Error Messages 153
LINEPROTO Error Message 154
LINK Error Messages 155
LLC2 Error Messages 159
LNMC Error Messages 160
LPD Error Message 161
M32 Error Message 162
MAILBOX Error Messages 162
MCI Error Messages 166
Table of Contents vii
SDLC Error Messages 224
SDLLC Error Messages 230
SEC Error Messages 231
SERVICE MODULE Error Messages 233
SLIP Error Messages 237
SMF Error Message 238
SMRP Error Messages 238
SNAPSHOT Error Messages 240
SNMP Error Messages 241
SSE Error Messages 242
STANDBY Error Messages 245
STUN Error Messages 247
SUBSYS Error Messages 251
SYS Error Messages 252
SYSMGT Error Messages 274
TAC Error Messages 275
TBRIDGE Error Messages 276
TCP Error Messages 278
TMQ Error Message 280
TN Error Messages 280
TN3270 Error Message 281
TR Error Messages 281
TUN Error Messages 295
UCODE Error Messages 296
Table of Contents ix UNIX Error Message 300
UTIL Error Messages 301
VINES Error Messages 302
VIP Error Messages 308
X25 Error Messages 309
XNS Error Messages 317
CIP System Error Messages 319
C1P-ADAPTER Error Messages 320
CIIP-BSQ Error Messages 325
CW-CBUSATTN Error Message 326
CIP-CBUS_WRITE Error Messages 327
CIP-CCA Error Messages 328
CIP-CLAW Error Messages 335
CIP-CONFIG Error Messages 342
CTP-CTA Error Messages 349
CIP-DEBUGGER Error Messages 356
CIP-DIAG Error Messages 359
CIP-DMA Error Messages 360
CW-GETDATA Error Message 362
CIEP-INT Error Messages 363
CIP-IPC Error Messages 365
Cifi-LOADER Error Messages 367
CIP-LOVE Error Message 386
CJP-MBUF Error Messages 386
System Error Messages CIP-MEMD Error Messages 387
CIP-MS0802 Error Messages 388
CIP-NEVADA Error Messages 397
CIP-OFFL Error Messages 399
CIP-SCB Error Message 406
CIP-SCHED Error Messages 406
CIP-SLC Error Messages 409
CIP-SS1802 Error Messages 411
CIP-SUBSYS Error Messages 412
CIP-SYS Error Messages 413
CIP-SYSMUT Error Messages 418
CIP-TCPIP Error Message 419
CIP-TN3270 Error Messages 419
System Pailure Error Messages 429
Index
Table of Contents xi XV System Error Messages LIST OF TABLES
Table Facility Codes xvii
xxii Table CIP Subfacility Codes
Table Error Message Severity Levels xxiii
in Error xxiv Table Representation of Variable Fields Messages
Table Token Ring Status Codes 294
Table Stack Trace Fields 430
List of Tables xiii xiv System Error Messages About This Manual
describes Cisco Internetwork Operating System Cisco lOS This publication lists and software sends these error messages to the console system error messages The system all to server on another system during operation Not system and optionally logging with Some are purely informational while error messages indicate problems your system with communications lines internal hardware or the others may help diagnose problems
system software
the crashes This manual also includes error messages that appear when system
How This Manual Is Organized
This manual contains three main chapters
of error related The System Error Messages chapter provides descriptions messages the CIP The are organized to the Cisco 105 software except for facility messages
that the The facility according to the particular system facility produces messages are and within each facility section messages sections appear in alphabetical order is followed by an explanation listed alphabetically by mnemonic Each error message the same and and recommended action If several error messages share explanation followed by the common recommended action the messages are presented as group action explanation and recommended
of error messages The CIP System Error Messages chapter provides descriptions to the particular related to the CIP facility The messages are organized according
the The subfacility sections appear in system subfacility that produces messages each section messages are listed alphabetical order and within system subfacility and Each error is followed by an explanation alphabetically by mnemonic message
About This Manual xv How to Read System Error Messages
recommended action if several error messages share the same explanation and
recommended action the messages are presented as group followed by the common
explanation and recommended action
The last chapter System Failure Error Messages covers error messages that appear when the system image crashes
The index of error messages is alphabetized as follows
Facility code
Subficility code if applicable
Mnemonic
Severity level
How to Read System Error Messages
System error messages begin with percent sign and are structured as follows
%FACILITY-SUBFACILITY-SEVERITY-MNEMONIC Message-text
FACILITY 15 code consisting of two or more uppercase letters that indicate the facility to of which the message refers facility can be hardware device protocol or module
the system software Table lists the system facilities codes
SUEFACILITY is code that is relevant only in Channel Interface Processor CIP error
messages Table lists the CIP subfacility codes For more information on CIP message format see the CIP System Error Messages chapter
SEVERITY i5 single-digit code from to that reflects the severity of the condition The
lower the number the more serious the situation Table lists the severity levels
MNEMONIC is code that uniquely identifies the error message
Mes sage-text is text string describing the condition This portion of the message
sometimes contains detailed information about the event including terminal port numbers
network addresses or addresses that correspond to locations in the system memory address
space Because the information in these variable fields changes from message to message
xvi System Error Messages How to Read System Error Messages
it is represented here by short strings enclosed in square brackets ii decimal number for example is represented as Table lists the representations of variable fields and the type of information in them
The following is sample system error message
%LINK-2-BADVCALL Ints TDTh
Table Facility Codes
Code Facility
AAA TACACS Authentication Authorization and Accounting
security
AlP ATM Interface Processor
ALIGN Memory optimization in reduced instruction-set computer
RISC processor
APPN Advanced Peer-to-Peer Networking
ARAP Apple Remote Access Protocol
AT AppleTalk
ATM Asynchronous Transfer Mode
BGP Border Gateway Protocol
BRI Integrated Services Digital Network ISDN Basic Rate
Interface
BSC Binary Synchronous Communications mode
BSTUN Block serial tunneling
CBUS ciscoBus controller
CCP Point-to-Point Compression Control Protocol
CI 75xx platform chassis interface
CIP Channel FACILITY Interface Processor See Table for CIP subfacility codes
CLEAR Clear fa ility
CLNS OSI Connectionless Network Services
About This Manual xvii How to Read System Error Messages
Table Facility Codes Continued
Code Facility
CLS Cisco Link Services
CLSDR Cisco Link Services Driver COMP Point-to-point compression
CONTROLLER Controller
CSC2 CSC2/CSC3 CPU cards
DBUS Data bus
DIALER Dial-on-demand routing
DIRRESP Director responder
DLC Data-link control DLSw Data-link switching
DMA Direct memory access
DNET DECnet
DNSIX Department of Defense Intelligence Information System Network Security for Information Exchange DSPU Downstream physical unit
DSX1 Channelized El Europe and TlUS telephony standard DUAL Enhanced Interior Gateway Routing Protocol DVMRP Distance Vector Multicast Routing Protocol EGP Exterior Gateway Protocol
ENV Environmental monitor card
ENVM Environmental Monitor for Cisco 7000 series
ETHERNET Ethernet for the C1000 series
FDDI Fiber Distributed Data Interface
FDDIS TAT FDDI state
FILESYS Personal Computer Memory Card International Association PCMCIA Flash card
xviii System Error Messages How to Read System Error Messages
Table Facility Codes Continued
Code Facility
FLASH Flash nonvolatile memory
FR Frame Relay ______Xerox GRIP Network Systems XNS Routing Protocol
RD HD64570 serial controller
HUB Cisco Ethernet hub
1BM2692 IBM Token Ring chip set
IGRP Interior Gateway Routing Protocol
IP Internet Protocol
IPC Interprocess Communication
TPFAST IP fast switching
IPRT Internet Protocol routing ______IPX Internetwork Packet Exchange Protocol
ISDN Integrated Services Digital Network
LANCE Local Area Network Controller Ethernet
LANE LAN emulation
LANMOR IBM LAN Network Manager ______LAPB XIS Link Access Procedure Balanced
LAT DEC Local Area Transport ______LEX LAN extension
LINEPROTO Line Protocol
LThIK Data link
LLC2 Logical Link Control type
LNMC LAN network manager ______
LPD Line printer daemon
M32 HDLC controller
MAILBOX ChipCom mailbox support
About This Manual xix How to Read System Error Messages
Table Facility Codes Continued
Code Facility MCI Multiport Communications Interface
MK5 MK5025 serial controller
MROIJTE Multicast route
NIETMGT Network Management
NHRP Next Hop Resolution Protocol
NIM Network interface module
OW Online insertion and removal
OSPF Open Shortest Path First
PA Port adapter
PAD X25 packet assembler/disassembler
PARSER Parser
PCBUS PC Industry-Standard Architecture ISA -to-Access Pro router interface
PPP Point-to-Point Protocol
QA Queue and accumulator
QLLC Qualified Logical Link Control
QUICC MC68360 Quad Integrated Communications Controller
RADIX Radix facility
RCMD Remote commands
REGEXP Regular expression parser
RIP IP Routing Information Protocol
RSP Route switch processor RSRB Remote source-route bridging
S4T68360 The port synchronous serial adapter based on the 68360
processor
SDLC Synchronous Data Link Control
xx System Error Messages How to Read System Error Messages
Table Facility Codes Continued
Code Facility
SDLLC SDLCILogical Link Control type LLC2 translation
SEC IP security
SERVICE_MODULE Service Module
SLIP Serial Line IP
SMF Software MAC error
SMRP Simple Multicast Routing Protocol
SNAPSHOT Snapshot dial-on-demand routing
SNMP Simple Network Management Protocol
SSE Silicon switching engine
STANDBY Hot Standby Router Protocol
STUN Serial tunneling ______
SUBSYS Software subsystems
SYS Operating system
SYSMGT System Management ______TAC Terminal Access Controller Protocol Access Control System
TBRIDGE Transparent bridging
TCP Transmission Control Protocol
TMQ Inbound terminal port queuing
TN Telnet
TR Token Ring ______TUN Tunnel
UCODE Microcode
UTIL Utility ______VINES Banyan VINES
VIP Versatile Interface Processor
About This Manual xxi How to Read System Error Messages
Table Facility Codes Continued
Code Facility
X25 X.25
Table CIP Subtacility Codes
Code Facility
ADAPTER Adapter processing
BSQ Buffer status queue processing
CBUS_ATTN ciscoBus controller statistics
CBUS_WRITE ciscoBus controller write support
CCA Channel card adapter
CLAW Common Link Access for Workstations
CONFIG Configuration processing
CTA Channel transport architecture
DEBUGGER Messages issued when nonrecoverable errors occur
DIAG Diagnostic processing
DMA Direct memory access
GET_DATA Internal routine for allocating transfer elements
INT Interrupt handler
IPC Interprocess Communication
LOADER Relocating loader
LOVE CIP-to-router statistics
MBUF Message buffer
MEMD Memory device
MSGSO2 IEEE 802.2cx Logical Link Control LLC protocol stack
NEVADA Internal controller
OFFL Offload protocol
xxii System Error Messages How to Read System Error Messages
Table CIP Subfacility Codes Continued
Code Facility
SCB Storage control block
SCHED Multitasking scheduler
SLC Serial link controller
551802 Common Service System Service Interface SSI
SUT3SYS Software subsystem
SYS CIP operating system
SYSMGT Network management processing for system management
remote procedure calls
TCPIP Transmission Control Protocol/Internet Protocol
TN3270 TN3270 server terminal emulation
Table Error Message Severity Levels
Level Description
unusable emergency System
needed alert Immediate action
critical Critical condition
error Error condition
warning Warning condition
condition notification Normal but significant
informational Informational message only
debugging Appears during debugging only
the by the logging global Error message severity levels correspond to keywords assigned The where and at what level these messages appear configuration commands that define For information the at the level more default is to log messages to console debugging and of the logging command in the see the system configuration chapter descriptions and command reference publications appropriate Cisco lOS configuration guide
About This Manual xxiii Error Message Traceback Reports
Table Representation of Variable Fields in Error Messages
Representation Type of Information
Decimal number
Hexadecimal number
Single character
Character string
Scientific notation
Address or node name
AppleTalk address
600-601 AppleTalk network either 600 or
Ethernet address for example 0000.FRED.OOCO
Internet address for example 12.128.2.16
Terminal line number in octal or decimal if the
decimal-flY service is enabled
VINES name or number hex or decimal
Error Message Traceback Reports
Some messages describe internal errors and contain traceback information This when information is very important and should be included you report problem to your
technical support representative
The following sample message includes traceback information
Process Exec level pith 17 Traceback 1A82 1AB4 6378 A072 1054 1860
xxiv System Error Messages System Error Messages
AAA Accounting Messages accounting error TACACS authentication authorization and accounting security
messages
Error Message %AAAA-3-BADSTR Bad accounting data
the internal database of accounting Explanation During AAA accounting operations indicates an internal information for user was found to be corrupt Tn all cases this information for user session has been lost software error and that accounting particular
and it to Recommended Action Copy the error message exactly as it appears report your
technical support representative
Error Message %AMA-3--NTJLUSR accounting for null user
internal software error During shutdown of line Explanation This message indicates an information via AAA but could not find or interface the system tried to send accounting The most reason for this error the user to which the accounting information belonged likely event This error can occur without is trying to do accounting twice for the same message information any loss of accounting
it and it to Recommended Action Copy the error message exactly as appears report your
technical support representative
System Error Messages AlP Error Messages
Error Message %AAAA3-RELOGIM sanity check in re-login to
Explanation software or hardware error occurred
Recommended Action the error Copy message exactly as it appears and report it to your technical support representative
AlP Error Messages
Interface ATM Processor error messages
Error Message
%AIP-3-AIPFAILSETUpVC Interface Failed to setup vc Cause
The AlP driver Explanation failed to set up virtual circuit
Recommended Action the error it Copy message exactly as appears and report it to your technical support representative
Error Message %AIP-3 _AIPFAILSETUPVCAVG Interface Failed to setup vc Cause Expected range Kbps for AlP Average Rate Metering Average RatePeak Rate Kbps turns Average Rate Metering OFF
Explanation software or hardware error occurred
Recommended Action Copy the error as it and message exactly appears report it to your technical support representative
System Error Messages ALIGN Error Messages
Error Message %AIP-3-AIPREJCMD Interface AlP driver rejected command error code Ox
command sent the Route Processor Explanation The AlP microcode rejected by RP the The error code is the status value returned by command
and it to Recommended Action Copy the error message exactly as it appears report your
technical support representative
ALIGN Error Messages
controls feature in reduced instruction-set computer The ALIGN facility
identifies software in need of use RISC-processor-based Cisco products that memory
optimization
Error Message %ALIGN-3-CORRECP Aligmnent correction made at reading/writing
needs Explanation software component within the router memory optimization
and it to Recommended Action Copy the error message exactly as it appears report your
technical support representative
Error Message %ALIGN-1-FATAL Illegal access to low address
could fatal error in software and not Explanation The router identified component
correct it
it and it to Recommended Action Copy the error message exactly as appears report your
technical support representative
System Error Messages ALIGN Error Messages
Error Message %ALIGI4-3-FjJLL Alignment log is full no new entries will be recorded
Explanation The router identified more software components in need of memory optimization than it can record
Recommended Action the Copy error as it and message exactly appears report it to your technical support representative
Error Message %ALIGN-3-NoM4 Not enough memory to start alignment subsystem
Explanation The router cannot start the memory performance monitoring system because not enough system memory is available for doing so
R commendecj Action the Copy error as it and message exactly appears report it to your technical support representative
Error Message %ALIGN3SPURIQIJS Spurious memory access made at reading
Explanation An error was identified and temporarily corrected within software component in the router
Recommended Action the Copy error as it and message exactly appears report it to your technical support representative
Error Message %ALICN-3-UNu5rj Unusual alignment correction at
Explanation An error was identified and temporarily corrected within software component in the router
Recommended Action Copy the error as it and message exactly appears report it to your technical support representative
System Error Messages APPN Error Messages
APPN Error Messages
Advanced Peer-to-Peer Networking error messages
Error Message %APPN- 1-APPNALERT
Explanation hardware or software error occurred
it and it to Recommended Action Copy the error message exactly as appears report your
technical support representative
Error Message %APPN-2-APPNCRIT
software error occurred Explanation hardware or
it and it to Recommended Action Copy the error message exactly as appears report your
technical support representative
Error Message %APPN APPNIDEBUG
software error occurred Explanation hardware or
and it to Recommended Action Copy the error message exactly as it appears report your
technical support representative
Error Message %APPN- -APPNENERG
occurred Explanation hardware or software error
and it to Recommended Action Copy the error message exactly as it appears report your
technical support representative
System Error Messages APPN Error Messages
Error Message %APPN-3-APPNERR
Explanation race condition occurred between two components in the APPN software
Recommended Action Copy t1e error message exactly as it appears and report it to your
technical support representative
Error Message %APPN-7-APPNETERROR
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %APPN3-APPNETLOG
Explanation hardware or software error occurred
Recommended Action Copy the errormessage exactly as it appears arid report it to your
technical support representative
Error Message %APPN6--APPNINIFO
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %APPN-6-APPNTLOGMSG
Explanation hardware or software error occurred
RecommendedAction Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages APPN Error Messages
Error Message %APPN-5-APPNNOTICE
Explanation hardware or software error occurred
it and it to Recommended Action Copy the error message exactly as appears report your technical support representative
Error Message %APPN-7-APPNSENDEVENT
occurred Explanation hardware or software error
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %APPN- -APPNSENDMSG
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
tebhnical support representative
Error Message %APPN- --APPNSENDREQ
Explanation hardware or software error occurred
and it to Recommended Action Copy the error message exactly as it appears report your
technical support representatiye
Error Message %APPN-4-APPNWAPNING
occurred Explanation hardware or software error
it to Recommended Action Copy the error message exactly as it appears and report your
technical support representative
System Error Messages ARAP Error Messages
Error Message %APPN7-MSALERT Alert issued with sense code by APPNCOMPLAIN_IVL
Explanation An alertable condition occurred in the local node
Recommended Action Refer to Detailed Alert section of the iBM Systems Network
Architecture Management Services Reference order number SC3O-3346 for description
of ALERTID Also refer to the Sense Data section of iBM Systems NetworkArchitecture
Formats order number 0A27-3 136 for description of SENSE_CODE Report this
message to your technj9al support representative
ARAP Error Messages
Apple Remote Access protocol error messages
Error Message %ARAP-3-ABORTED flY arap callback aborted
Explanation An unexpected message was received during the Microcom Networking
Protocol version MNP4 link setup
Recommended Action Report this error to your technical support representative
Error Message %ARAP-6-ADDRFREE flY ARAP ended for user address
Explanation This message appears only when ARA protocol logging is configured The
message notes that an ARA protocol user has logged out
Recommended Action No action is required
System Error Messages ARAP Error Messages
Error Message %ARAP-6-ADDRUSEDflY ARAP started for user address
is The Explanation This message appears only when ARA protocol logging configured message notes that an ARA protocol user has logged in
Recommended Action No action is required
Error Message %ARAP-3-BADCONFIG flY unhandled configuration command
Explanation configuration command was not recognized
Recommended Action Check the configuration file on the server for any invalid
configuration commands
Error Message %ARAP-6-BADEXIP flY exited user
time The Explanation user was disconnected from ARA protocol at an unexpected disconnection may be due to modems dropping server error client problems or any number of other difficulties
Recommended Action To determine the cause of the disconnection correlate the receipt
of this message with the user problem reports
Error Message %ARAP-3-BADPAK flY Bad packet type in arap_send_msg
Explanation Internal data structures are corrupted
Recommended Action Check for abnormally high CPU usage
System Error Messages ARAP Error Messages
Error Message %ARAPr4-CONFAIELED flY ARAP connection failed
Explanation The ARA protocol client was denied access probably due to configuration
problem on the servet The error message should indicate the problem This message does not indicate access denials due to bad passwords
Recommended Action Investigate the problem reported in the error message
Error Message %ARAP-4--OETBUFFER getbuffer failed size
Explanation The ARA protocol could not obtain buffer for an incoming packet
Recommended Action Examine buffer usage statistics More memory might be required
Error Message %ARAP-5--INITCONFUSED flY APAP unexpected initialization packet
Explanation The startup negotiation between client and the ARA protocol server fell out
of order If this message is received sporadically it indicates line noise
Recommended Action If this message recurs reinstall the ARA client software
Error Message %ARAP4-NOEXflACACS fly arap TACACS is configured but extended TACACS is not
Explanation Terminal Access Controller Access Control System TACACS
authentication failed because extended TACACS is not configured
Recommended Action Configure extended TACACS
10 System Error Messages AT Error Messages
Error Message %ARAP-3-NOMIM flY ARAP session failed no memory
it could not allocate for Explanation ARA protocol failed to run because enough memory
its internal data structures
Recommended Action Run show mem for details of memory usage You probably need
to install more memory
Error Message %ARAP-5--PNCINVALID flY ARAP invalid packet received
code Explanation corrupted packet reached the ARA protocol
excessive line noise Recommended Action Check for excessive CPU usage or
Error Message %ARAP-4-TIMEOTJT fly arap expected message timeout
link Explanation The software timed out during the MNP4 setup
Recommended Action Report this error to your technical support representative
AT Error Messages
AppleTalk error messages
Error Message %AT-6-ACQUIREMODE AppleTalk port initializing acquiring
This is Explanation The port is determining the correct configuration message generated
is detected when discovery mode is enabled and no other router
action Recommended Action Informational message only No required
System Error Messages 11 AT Error Messages
Error Message %AT-5-ADDRINUSE AppleTalk node warning address already in use
Explanation The initial hint address was in use search will be made for valid address
Recommended Action Notification message only No action required
Error Message %AT-5---ADDRINVALID AppleTalk node warning address atalk_address is invalid
The hint address Explanation specified for the port was not valid for its current
configuration
Recommended Action No action required the hint is ignored and random valid hint is
automatically computed
Error Message %AT-6-7JJDRUSED AppleTalk node up using address
hint address Explanation No or bad hint address was specified This message indicates which AppleTalk address will be used
Recommended Action Informational message only No action required
Error Message %AT-2-ASSERTFAILED AppleTalk assertion failed
The Explanation software detected an inconsistency Although this error is serious the router attempts to continue AppleTalk processing can be impaired
Recommended Action Record the entire message and note anyAppleTalk problems you experience Give this information to technical your support representative in problem report
12 System Error Messages AT Error Messages
Error Message %AT-5-BADNEIGHBOR AppleTalk neighbor ignored is misconfigured
does not with this Explanation neighboring routers AppleTalk configuration agree result from mismatch between the routers AppleTalk configuration This condition can neighbors network hinge and this routers network range
routers Recommended Action Modify either this routers or the neighboring configuration so that the network ranges agree
Error Message %AT6-BADROUTE Route to has gone bad
timeout Explanation The system did not detect route within the required period network has become Therefore the route is marked as bad This can mean that This does not unreachable for some reasonperhaps broken connection message
necessarily reflect an error condition
action Recommended Action Informational message only No required
Error Message %AT-7-BUGREPORT AppleTalk Bug
condition The router takes corrective Explanation The software detected an unexpected
action and continues
it and note Recommended Action Copy the error message exactly as appears any technical for AppleTalk problems you experience Contact your support representative
assistance
System Error Messages 13 AT Error Messages
Error Message %AT-3--CANTDEL Cannot delete route by clearing please remove by reconfiguration
Explanation The user attempted to remove route from the routing table with the
conunand clear appletalk route The command failed because the route was directly
connected that is it was created by configuration command
Recommended Action Remove the route by reconfiguring the directly connected
interface with which it is associated
Error Message %AT5-COMPATERRI AppleTalk internet compatibility mode required by
Explanation neighboring router only supports extended AppleTalk networks with
cable range of and with one assigned zone for example 25-25
Recommended Action Upgrade routers that can support only the original AppleTalk
specification and observe the compatibility rules in the interim
Error Message %AT5--COMPATERR2 AppleTalk neighbor incompatibility net has multiple zones
Explanation Although this router has neighbors that require your internetwork to observe
compatibility rules AppleTalk has learned of route with multiple zone names defined
This condition can cause inconsistencies for nodes in your internet
Recommended Action Upgrade routers that can support only the original AppleTalk
specification and observe the compatibility rules in the interim
14 System Error Messages AT Error Messages
Error Message %AT5-CONPATERR3 AppleTalk neighbor incompatibility has wide cable-range
internetwork to observe Explanation Although this router has neighbors that require your that has wide than cable compatibility jiules AppleTalk has learned of route greater inconsistencies for nodes in internetwork range This condition can cause your
Recommended Action Upgrade routers that can support only the original AppleTalk in the interim specification and observe the compatibility rules
Error Message %AT5-COMPATERR4 AppleTalk EIGRP neighbor incompatibility has same routeiL ID dec
Explanation hardware or software error occurred
and it to Recommended Action Copy the error message exactly as it appears report your technical support representative
Error Message %AT-6-CONFICOK AppleTalk port enabled verified
the indicated router Explanation The AppleTalk configuration was verified by consulting
Recommended Action Informational message only No action required
Error Message %AT-6-CPUPIG AppleTalk Cpu piggie info just spent ms without schedule
occurred Explanation hardware or software error
and it to Recommended Action Copy the error message exactly as it appears report your
technical support representative
System Error Messages 15 AT Error Messages
Error Message %AT-7-DEBJJQI4SG AppleTalk Debug
This Explanation message is generated by debug command to provide additional information about condition in AppleTalk
Recommended Action If in show you experience problems AppleTalk these messages to your technical support representative
Error Message %AT3-DEFZONEERR AppleTalk port warning default zone differs with
Explanation This is the message generated during verification startup process when there is disagreement between the default zone the first zone defined after the appletalk and cable-range command the router that confirmed the configuration When an
AppleTalk end node is first connected to network it joins this default zone until it is overridden
Recommended Action Correct the that configuration so all routers are advertising the same default zone Note that several router implementations are known to mismanage the default zone
Error Message %AT-6-DELROTJTE AppleTalk network deleted removed from routing table
Explanation route aged out of the AppleTalk internetwork
Recommended Action Informational message only No action required
Error Message
%AT-5-DISCOFF AppleTalk node warning discovery mode disabled
Explanation hardware or software error occurred
Recommended Action Copy the error as it and message exactly appears report it to your technical support representative
16 System Error Messages AT Error Messages
Error Message %AT-3-DOt4LOOP LOOP Detected on Domain
the domain router Explanation routing ioop was detected by
in the of the Loops are not allowed however loop detection process running background domain router new zone list domain router tries to spot loop situation Whenever gets and the of from one of the domains that is identical to one in the main routing table length
detection the network range matches it starts loop process
which are NBP of loop detection process sends several AppleTalk loop packets packets
is received on the interface that does not belong to type LoopBack When loop packet the and all the the original domain the domain router shuts off all domains subsequently
interfaces in these domains which are involved in the loop
of the to make Loop detection may not catch all types of loops It is the responsibility user
sure that no loop exists
Recommended Action Disable the cause of the routing loop Restart the interfaces
involved
Error Message %AT-3-DOMOVERFLOW Remap Range OVERFLOW for Domain
network cannot fit inside the Explanation The remap range overflowed If range
until more room is available When remapping range then it is not accepted remapping disabled overflow occurs all interfaces in the domain are
the interfaces Recommended Action Increase the remapping range Restart
System Error Messages 17 AT Error Messages
Error Message
%AT-5-DUPADDR AppleTalk port restarting node address taken by
Explanation Another node AppleTalk on common network interface claimed the same AppleTalk address that this router was This indicates using error serious unexpected If it problem recurs physical network problem in which the nodes cannot hear each other may exist
Recommended Action This router will restart AppleTalk processing on the common network interface to resolve the address conflict No action required
Error Message %AT-6-EIGRpLINJKDN AT/EIGRP Link Down
Explanation hardware or software error occurred
Recommended Action Copy the error as it message exactly appears and report it to your technical support representative
Error Message %AT-6EIGRPLJNXJJP AT/EIGRp Link Up
Explanation hardware or software error occurred
Recommended Action Copy the error as it and message exactly appears report it to your technical support representative
Error Message
%AT6-EIGRPLOG EIGRP Logging from on for network metric
Explanation hardware or software error occurred
Action Recommended Copy the error as it and message exactly appears report it to your technical support representative
18 System Error Messages AT Errpr Messages
Error Message
%AT-4-EIGRPLOTSOWORK AT/EIGRP WorkQ processed 11dec11 entries required ms we did suspend
Explanation hardware or software error occUrred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %AT-6-EIGRPPEERDN AT/EIGRP Peer Down router ID just lost on
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %AT-6-EIGRPPEERUP AT/EIGRP Peer Up router ID newly heard on
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %AT-5-FDDICOMPAT AppleTalk FDDI neighbor using obsolete FDDI addressing
release of Explanation Another router on an FDDI ring running AppleTalk is running
software releases earlier than the router software previous to 9.02 Routers running 9.02
that is not with the use an encapsulation for AppleTalk on FDDI rings compatible
Apple FDDITa1k preliminary proposal
Recommended Action Notification message only No action required
System Error Messages 19 AT Error Messages
Error Message %AT3-IFCONIFLICT AppleTalk port disabled conflicts with port
Explanation An attempt was made to configure an interface to have the same or
conflicting AppleTalk address or cable range as another interface on the same router
Recommended Action Verify that you are not specifying an AppleTalk address or cable
range used previously on this router and reconfigure the interface
Error Message %AT-5-INTCLEARED AppleTalk port restarting interface cleared
Explanation This message is generated by performing the EXEC command clear
interface on an interface currently routing AppleTalk
Recommended Action Notification message only No action required
Error Message %AT5-INTDOWN AppleTalk node down Line protocol down
Explanation An AppleTalk hardware interface was disabled because of bad serial line
configuration command or bad interface
Recommended Action If the port was not intentionally disabled this message can reflect
hardware problem If so repair or replace the controller
Error Message %AT-5-INTRESTART AppleTalk port restarting protocol restarted
Explanation This message is generated when configuration change necessitates
resetting the hardware interface AppleTalk reinitialized the port
Recommended Action Notification message only No action required
20 System Error Messages AT Error Messages
Error Message %AT-6-INTUP AppleTalk port restarting Line protocol came up
shut down was restarted Explanation An AppleTalk port that was previously
Recommended Action Informational message only No action required
Error Message %AT3-INVNBPCMD Invalid NBPtest command
in the Name Protocol Explanation An unrecognized command was given Binding NBP test facility
Recommended Action Enter valid command
Error Message %AT-5-LOSThEIGHBOR AppleTalk neighbor down lost contact with
Explanation peer router is unreachable
Recommended Action Notification message only No action required
Error Message %AT-3-MACIPBADCONF ZONE-NAME MacIP inoperable configuration X.X.X.X
conmiand is this Explanation If the appletalk event-logging configured message of MacJP server cannot or recover operations because appears on the console when begin occurs when the MacIP an invalid IP address configuration This condition only configured IP interface An servers IF address is not valid on the same cable of any operable AppleTalk The MacIP servers IF zone of the MacIP server replaces ZONE-NAME configured
address replaces X.X.X.X
invalid and is deleted When this error occurs the MacIP configuration is considered
Recommended Action Advisory message No action required
System Error Messages 21 AT Error Messages
Error Message %AT-6-MACIPDOWN ZONE-NAME MacIP server shutting down X.x.x.x
Explanation If the appletalk event-logging command is configured this message appears on the console when MacIP server is no longer operational for any reason MacIP servers shut down in to MacIP response configuration changes or errors or change in the condition or of configuration an AppleTalk or IF interface for which the MacIP server is service An providing AppleTalk zone of the MacIP server replaces ZONE-NAME The MaciF servers configured IP address replaces X.X.X.X
Recommended Action Informational message only No action required
Error Message
%AT-3-MACIPNOCABLE ZONE-NZME MacIP inoperable IP interface X.X.X.x
Explanation If the appletalk event-logging command is configured this message appears on the console when MacIP server can no longer operate due to change in the
condition of the IP interface it serves This condition can occur if IP routing is shut down on the interface or the IP address of the interface is changed so that the MacIP servers IP
address is no longer valid on the same cable An AppleTalk zone of the MacIP server replaces ZUNE-NAJyIE The MaciF servers configured TP address replaces X.X.X.X
Recommended Action Advisory message only No action required
Error Message %AT-6-MACIprjp ZONE-NM4E MacIP server operational x.x.x.x
Explanation If the appletalk event-logging command is configured this message appears on the console when MaciF server is initialized fully and is ready to accept client An served requests AppleTalk zone by the MacIP server replaces ZONE-NAME The MacIP servers configured IP address replaces X.X.X.X
Recommended Action Informational message only No action required
22 System Error Messages AT Error Messages
Error Message %AT-3--MCMISMATCH AppleTalk port warning zone multicast differs with
with that another Explanation computed multicast address disagrees provided by
AppleTalk router The other AppleTalk router may be misconfigured or faulty
Recommended Action Correct the problem at the other routet
Error Message %AT-6-NBRDELETED Neighbor entry for has been deleted
of the Explanation This message is displayed upon successful completion EXEC command clear appletalk neighbor
Recommended Action Informational message only No action required
Error Message %AT-6-NEIGHBORUP AppleTalk neighbor up has restarted
Explanation neighboring router to which this router previously lost connectivity
reappeared on the network
Recommended Action Informational message only No action required
Error Message %AT-3-NETDISAGREES AppleTalk port disabled network incompatible with
address or cable Explanation The port was disabled because the configured AppleTalk the attached network range on the interface conflicts with another router on
Recommended Action Reconfigure the applicable routers
System Error Messages 23 AT Error Messages
Error Message
%AT-4-NETiqvpjiD AppleTalk node down conflicts with active internet
Explanation The for the configuration specified interface conflicts with the active
AppleTalk internetwork For cable is example range configured so that it overlaps an but existing route does not match the entry exactly
Recommended Action the so that it is Reconfigure port cOnsistent with the existing internetwork or take other actions any necessary to resolve the conflict AppleTalk will
periodically attempt to restart the port
Error Message %AT-6-NEWNEICHBOR AppleTalk neighbor added is operational
The Explanation router discovered new AppleTalk router
Recommended Action Informational message only No action required
Error Message %AT-6-NEWR0uTE AppleTalk network added via hop
Explanation new route has been learned The AppleTalk message includes the source of the route and its distance in hops
Recommended Action Informational message only No action required
Error Message
%AT-6-IcEWzQNE AppleTalk zone added zone defined
Explanation new AppleTalk zone has been created
Recommended Action Informational message only No action required
24 System Error Messages AT Error Messages
Error Message %AT-3-NOADDRSAVAIL AppleTalk node down no addresses available
Explanation No free node could be found on the interface
Recommended Action If fewer than 250 nodes reside on your AppleTalk network call must network your technical support representative Otherwise you split your AppleTalk into smaller networks
Error Message %AT-3-NOBESTPATH Could not compute best path for network
be found Explanation path to the specified network could not
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %AT-6-NODEWRONG AppleTalk node misconfigured reply has been broadcast
this router an Explanation An AppleTalk node sent GetNet Info request to specifying
invalid network number for the source of the GetNet Info request This situation occurs
and is therefore when an AppleTalk end node is moved between networks misconfigured
for the current network
Recommended Action Informational message only No action required
Error Message %ATl-NOMEM Could not allocate memory for at line in
Explanation An internal software error occurred
and it to Recommended Action Copy the error message exactly as it appears report your
technical support representative
System Error Messages 25 AT Error Messages
Error Message %AT-6-NopRoxy AppleTalk proxy deleted zone freed network
Explanation previously configured Name Protocol Binding NBP proxy was deleted The router can no convert longer NBP requests to format understood by routers that support only the original specification of AppleTalk
Recommended Action Informational message only No action required
Error Message %AT-3-N0ROUTE No route to destination
Explanation The router could not deliver packet to destination because it did not know where to send it
Recommended Action If the destination is valid you must determine why the router does not know the route that is the neighboring router may be withholding information
Error Message %AT-3NOSRCADDR AppleTalk packet error no source address available
Explanation An to attempt generate an AppleTalk packet from the router failed because valid no AppleTalk source address is available to identify this router in the packet
Recommended Action to have address Configure port an or cable range and verify that the port is operational
Error Message %AT-3-NoSuciijR No such neighbor net
Explanation The user tried to execute the EXEC commands show appletalk neighbor or clear appletalk neighbor with nonexistent neighbor address
Recommended Action Specify valid that neighbor address is one that appears in the output of the show appletalk neighbor command with no arguments
26 System Error Messages AT Error Messages
Error Message %AT-5-NOSUCHROUTE No such route
show route or Explanation The user tried to execute the EXEC commands appletalk clear appletalk route with nonexistent route
that in the of the Recommended Action Specify valid route that is one appears output show appletalk route command with no arguments
Error Message %AT-3-NOTRtJNNING AppleTalk not running
the when Explanation You tried to show or change AppleTalk configuration AppleTalk turned routing was not on
Recommended Action Issue the appletalk routing configuration command prior to command issuing any other AppleTalk configuration or display
Error Message %AT-5-NOTSUPPORTED AppleTalk node down line protocol not supported
method that does not Explanation The specified interface has an encapsulation support AppleTalk
action Recommended Action Notification message only No required
Error Message %AT-3-NOVIRTTJAL Client tried to connect but no virtual network is declared
occurred Explanation hardware or software error
it to Recommended Action Copy the error message exactly as it appears and report your
technical support representative
System Error Messages 27 AT Error Messages
Error Message %AT-5--OLDMCI AppleTalk route cache disabled firmware is obsolete
Explanation The firmware on the MCI controller card does not support AppleTalk last
switching
Recommended Action No corrective action is required Normal AppleTalk operation is
permitted but the fast switching cache is disabled for the associated port If unexpected
verify that the MCI controller firmware for the interlace specified in the error message is at
level 1.7 or higher
Error Message %AT6--ONLYROUTER AppleTalk port enabled no neighbors found
Explanation No other AppleTalk routers were found on the network attached to the port
Recommended Action Informational message only No action required
Error Message %AT6--OUTOFSYNC AUR connection out of sync. terminating
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %AT-6--PATHADD AppleTalk path to network added via metric dec
Explanation new AppleTalk path has been learned The message includes the source of
the path its distance in hops its metric and the type of path
Recommended Action Informational message only No action required
28 System Error Messages AT Error Messages
Error Message %AT-5-PATHCHANGE Route to is now using path of type on via
Explanation The path to network changed either because the old path went down or the new path was better
Recommended Action Notification message only No action required
Error Message %AT-6-PATHDEL AppleTalk path to fatalknet via has been deleted
Explanation path aged out of the AppleTalk network
Recommended Action Informational message only No action required
Error Message %AT-6-PATHNOTIFY AppleTalk path to down reported bad by
Explanation router went down somewhere on the AppleTalk network The specified peer notified this router of the change
Recommended Action Informational message only No action required
Error Message %AT-4-PATHREJECTED AIJRP path rejected conflict detected
Explanation hardware or software error occurred
and it to Recommended Action Copy the error message exactly as it appears report your technical support representative
System Error Messages 29 AT Error Messages
Error Message %AT6-REGPENDING NBP registration of pending
Explanation name registration call is being performed
Recommended Action Informational message only No action required
Error Message %AT-6-ROUTEDOWN AppleTalk network down port to disabled
Explanation connected route is being advertised as down also known as not/y
neighbor because the configured port is no longer operational
Recommended Action Informational message only No action required If unexpected
correct the situation that caused the port to be disabled
Error Message %AT6-ROUTENOTIFY AppleTalk network down reported bad by
Explanation router went down somewhere on the AppleTalk network The specified
peer notified this router of the change
Recommended Action Informational message only No action required
Error Message %AT-6--ROUTEOK AppleTalk network up via hop
Explanation routing update was received for previously suspect route
Recommended Action Informational message only No action required
30 System Error Messages AT Error Messages
Error Message %AT-5--RTMPSTATE RTMP Path to via node now in state metric
Explanation The state of path changed
Recommended Action Informational message only No action required
Error Message %AT-3 -SUBROUTINE_ERROR AppleTalk error
Explanation An internal error occurred that violates programming assertion in the
AppleTalk networking module
Recommended Action Save the text of the message the output of the show version command and copy of the router configuration file Call your technical support representative for assistance
Error Message %AT3-ZONEDISAGREES AppleTalk port disabled zone list incompatible with
Explanation The configurations of one or more other routers are inconsistent with the configuration of this router
Recommended Action Reconfigure the routers so they are all consistent
Error Message %AT-6-ZONEGC AppleTalk zone deleted zone released
Explanation The router purged an unused zone from the zone table
Recommended Action Informational message only No action required
System Error Messages 31 ATM Error Messages
Error Message %AT-6-ZONEPROXY AppleTalk proxy defined zone using network
Explanation This message reports the zone name and network number that are being
advertised to support the appletalk nbp-proxy command
Recommended Action Informational message only No action required One message is
generated for each configuration command when proxy service is initiated
ATM Error Messages
Asynchronous Transfer Mode error messages
Error Message %ATM3-FAILCREATEIJC ATh failed to create VCVCD VPI VCI on Interface Cause of the failure
Explanation This message can occur for the following unrelated reasons Each reason is accompanied by recommended action
The virtual circuit descriptor VCD exceeded the maximum available memory
Use smaller VCD numbet
Address Resolution Protocol ARP is allowed only on AAL5-SNAP virtual circuits
Change the encapsulation to AAL5SNAP
The virtual path identifier-virtual channel identifier YPI-YCI pair or the VCD is
already in use
Try using different VPI-VCI or VCD number
virtual connection is allowed interface Only one channel VCC on point-to-point
Try using different subinterface
AAL3/4-SMDS virtual circuit must be the only virtual circuit on an interface
Turn off AAL3/4
32 System Error Messages ATM Error Messages
AAL3/4-SMDS multiplex ID exceeds the maximum
Try smaller multiplex ID value
Switched Multimegabit Data Service SMDS is not enabled
Enable SMDS
failed The driver to accept the virtual circuit
Try initiating the virtual circuit again
Recommended Action If none of the previous actions fix the problem copy the error message exactly as it appears and report it to your technical support representative
Error Message %ATM-4-MIUCALLMISNATCH Incoming call from NSAP has mismatched maximum transmission unit incoming forward PDU size is backward PDU size is interface MTU size is
Explanation The calling or called party has maximum transmission unit MTU size configured that is different from the MTU size on the current interface
Recommended Action Either change the configured MTU size on the current interface to that of the callers or called partys interface or change the callers or called partys interface to match the current interface
Error Message %ATM4-N0MEM Failed to allocate memory-- ONEMIN
Explanation The system attempted to allocate some memory but failed
Recommended Action Reduce the RAM usage or add more RAM to your router
System Error Messages 33 BGP Error Messages
Error Message %ATM-3-tJNSUPPORTEQQ0S_PARMASATM failed to create VC on Interface hit Cause of the failure Invalid traffic shaping parameters or out of rate queues
Explanation The system attempted to create virtual circuit YC with traffic shaping parameters not supported by the hardware
Recommended Action Either change the requested traffic shaping parameter to one that
the hardware supports or use existing parameters to avoid the need for new rate queue
BGP Error Messages
Border Gateway Protocol error messages
Error Message %BGP-6-ASPATHJ5 Invalid AS path received from
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %BGP-3-BADMASK Attempt to install route for without valid mask in
Explanation An internal software error occurred
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
34 System Error Messages SGP Error Messages
Error Message %BGP-6-NEXTHOP Invalid next hop received from
Explanation The remote BGP peer sent in route with an illegal next hop.The given route was ignored
Recommended Action This is an informational message only The remote peer may be misconfigured
Error Message %BGP-3-NOMEMORY No memory for entry resetting
Explanation The requested operation could not be accomplished because of low memory condition
demands If Recommended Action Reduce other system activity to ease memory conditions warrant upgrade to larger memory configuration
Error Message %BCP3-RZDIXINIT Radix tree initialization failed
Explanation Initialization of the radix tree could not be accomplished because of low memory condition
demands If Recommended Action Reduce other system activity to ease memory
conditions warrant upgrade to larger memory configuration
System Error Messages 35 BRI Error Messages
BRI Error Messages
ISDN Basic Rate Interface error messages
Error Message %BRI-3--BAIJENCAP Unit bad encapsulation in idb-enctype
%BRI-3--BADUNIT Bad unit number
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %BRI-F-INITFAIL Unit initialization timeout failure
Explanation The hardware failed to initialize correctly
Recommended Action Repair or replace the controller
Error Message %BRI-O-NONEMORY Unit no memory for
%BRI-1--NOMEMORY msgtxt_nomernory
Reconrnended Action The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If
conditions warrant upgrade to larger memory configuration
Error Message %BRI-3--ODDSTART Interface
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
36 System Error Messages BSC Error Messages
Error Message %BRI-3-OUTENCAP Unit bad output packet encapsulation hex
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %BRI-3-OWNERR Unit buffer ownership error
Explanation An Ethernet interface is malfunctioning or an internal software error occurred
Recommended Action Repair or replace the malfunctioning controller
BSC Error Messages
Binary Synchronous Communications Bisync protocol error messages
Error Message %BSC-3-BADLINESTATE Line state Tx when receiving non-Tx event decj
Explanation An unexpected receive occurred during transmission
Recommended Action Verify that the line has been consistently defined in regards to the
carriet If message report was sent perform hardware reset on the bisynchronous
interface in question
Error Message %BSC-3-BADPEERTYPE Peer is incorrect type
local-ack is It indicates the Explanation This message occurs only when BSC configured serial interfaces that are using the BSTUN tunnel are configured incorrectly that is both
have been configured as secondary
Recommended Action Reconfigure the serial interfaces correctly to be primary and
secondary pair
System Error Messages 37 BSTUN Error Messages
Error Message %ESC-2--NOMEM No buffers available on interf ace
Explanation This message indicates that memory in the router was exhausted
Recommended Action Perform diagnostics on the router to locate the subsystem or
interfaáe responsible for consuming memory The only method that will clear this situation
is to reload the routet
BSTUN Error Messages
Block serial tunneling error messages
Error Message %BSTIJN3-BADcONN CONN bad connection peer
%ESTUN-3-BADLENOP bad len or unknown op op len
%BSTUN-3-BADMAGIC wrong magic mine theirs
%BSTUN3-BADMAGICTCP peer wrong magic mm theirs
%BSTtJN-3-BADPASSIVEOPEN passive open from failed
%BSTUN3-CONNILLSTATE CONN Peer illegal state
Explanation An internal software error occurred
Recommended Action If any of these messages recur call your technical support
representative for assistance
38 System Error Messages BSTIJN Error Messages
Error Message %BSTON-6-CONNOPENFAIL CONN peer open failed
Explanation An attempt to connect to remote TCP BSTUN peer failed
Recommended Action Verify that the remote peer is accessible from this router that it is running software capable of supporting BSTUN and that it is configured correctly
Error Message %BSTUN-6-ERR op len
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %BSTLJN-2-NOBUF Interface no buffer available to
Explanation memory shortage existed at the time that the configuration command was issued This condition is rare and under normal conditions temporary
Recommended Action Reconfigure the BSTUN group If memory shortages persist call your technical support representative for assistance
Error Message %BSTtJN3-NOGRPDEF No bstun group defined on interface
Explanation An action was taken that requires the previous definition of BSTUN group numbet
Recommended Action Make sure that the encapsulation bstun and bstun group commands have been used to define BSTUN encapsulation and the STUN group for the interface
System Error Messages 39 BSTUN Error Messages
Error Message %BSTUN-3-NOPROTMEM No memory for BSTIJN protocol definition of
Explanation The system does not have sufficient memory to define new BSTUN schema
Recommended Action This error message should only print when the router is critically
short of memory Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %BSTUN-6-OPENED peer opened state
%BSTUN-6-OPENING CONN opening peer
%BSTUN-6-PASSIVEOPEN passive open
Explanation connection attempt to remote peer completed successfully OPENED
PASSIVE-OPEN or is in the process of being opened OPENING This is good expected behavior
Recommended Action Informational message only No action required
Error Message %BSTUN6-PEERSHUTDOWN shutting down peer on
Explanation connection to remote peer is being shut down This is typically the result
of user intervention in BSTUN reconfiguration or disabling This is good expected behavior
Recommended Action Informational message only No action required
40 System Error Messages BSTJN Error Messages
Error Message %BSTUN-4-PEERSTATE Peer wrong state
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %BSTUN6-PROCEXIT Process terminating Due to signal Subcode Address
Explanation The BSTUN background process is terminating
Recommended Action If this message appears while you are unconfiguring STUN no action is required Otherwise record all the displayed values and any other BSTUN error messages and contact your technical support representative
Error Message %BSTUN-6-RECONNECT PHDR reconnect from peer
Explanation remote peer reestablished connection to this router
Recommended Action Informational message only No action required
Error Message %BSTUN-3-SENDPUNT sent to
%BSTUN-3-SENDPIJNTrCP sent to
Explanation An internal software error occurred
technical Recommended Action If either message recurs call your support representative for assistance
System Error Messages 41 BSTUN Error Messages
Error Message %BST%JN-6-TCPFINI peer closed state
Explanation remote peer closed BSTUN connectioti with this router
Recommended Action Examine the other router to see why it closed this connection with
this peer This can be caused by normal events such as reconfiguration
Error Message %BSTUN-6-TCPPEERSHUT
Explanation This route closed BSTUN connection with remote peer
Recommended Action Examine this router to see why it closed this connection with this
peer This can be caused by normal events such as reconfiguration
Error Message %BSTUN-3-TJNXPROTOEV Unknown protocol event on interface
Explanation non-decodeable event was passed to the BSUTN layer for processing
Recommended Action Perform hardware restart on the indicated interface
42 System Error Messages CBUS Error Messages
CBUS Error Messages
CiscoBus controller error messages
Error Message %CBUS-3-AIPCFG Interface Cannot config interface AlP MEM status
%CBUS-3-AIPINVPLIM Interface Invalid PLIM detected Interface downed
%CBUS3---AIPRSET Interface Error aip_reset
%CBUS-3-AIPRSETU Unit Error aip_reset
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CBUS-4-BADENCAPSZ CIP encapsulated msg size exceeds wax
Explanation An encapsulated control message from the CII had size greater than the
maximum expected size The message was truncated
it and down the Recommended Action Copy the error message exactly as appears copy
routers configuration along with any other relevant information Contact your technical
support representative for assistance
Error Message %CBUS-3-BIGBUFCcntroller Error Big Buffers
Explanation hardware or software error occurred
and it to Recommended Action Copy the error message exactly as it appears report your
technical support representative
System Error Messages 43 CBUS Error Messages
Error Message %CBUS-3--BTJFFER Controller Error But fersize
Butferpool number
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CBIJS-3---CBUSBCE Failed to select BCE response cbus_bce_updatejfa
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CBUS3--CBUSBCEPERM Failed to select BCE response cbus_bceperrniss ions_update
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Explanation
%CBIJS-3-CCBCMDFAILQ Controller cmd failed
Explanation command sent from the system to an interface processor failed to
complete successfully
Recommended Action The system recovered by generating an error code to the
requester
44 System Error Messages CBUS Error Messages
Error Message %CBUS3-CCBCMDFAIL1 Controller and Ox%-08x failed Ox%04x
Explanation command sent from the system to an interface processor failed to complete successfully
Recommended Action The system recovered by generating an error code to the requester
Error Message %CBUS-3-CCBPTIMEOUT CCB handover timed CCB slot
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CBUS-3-CCBREPLY bad CCB reply hex
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CBUS-4-CIPADPTCHt4G InLerface adapter changed from to
Explanation The port adapter on the CIP interface reported different interface type than it previously did which should not happen without your removing the CIP and reinstalling it
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 45 CBUS Error Messages
Error Message %CBUS-3-CIPCFGFAIL configuration command failed
Explanation configuration command sent to the ClIP after reset failed to complete
successfully
Recommended Action Reissue the configuration command
Error Message %CBUS-3-CIPDTRFAIL Channel-protocol corrmand failed resetting to default
Explanation The channel-protocol configuration command sent to the CIP after reset
failed to complete successfully
Recommended Action The channel data transfer rate was reset to the default value
Reissue the configuration command
Error Message %CBUS-3-CIPRNCAP No elements available for message
Explanation An encapsulated control message arrived from the but no elements were available to receive it The Route Processor RP or the RSP will reset the interface
Recommended Action Copy the error message exactly as it appears and copy down the
routers configuration along with any other relevant information Contact your technical
support representative for assistance
Error Message %CBUS-3-CIPNOPREQ Unable to pre allocate response element cfg not sent
Explanation An attempt to allocate buffer for the ClIP configuration response or for the
configuration state change request was unsuccessful The configuration request was not
sent to the ClIP
Recommended Action The configuration command must be reissued
46 System Error Messages CBUS Error Messages
Error Message %CBUS-3-CIPRSET Interface Error cip_reset
Explanation The Channel Interface Processor CIP did not respond to reset request from the route processor
Recommended Action
Try each of the following fixes in sequence If fix corrects the problem theres no need to perform the tasks which follow it
Clear the interface using the clear interface command
Mic reload
Reseat the CIP
If the error still occurs copy the error message exactly as it appears Record the output from the following commands
show contr cbus
show version
show interface
write term
show running-config
Record any of the other log messages that surround the CIPRSET message Provide this information to your technical support representative
Error Message %CBUS3-CMD Crud failed response %04x
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 47 CBUS Error Messages
Error Message %CBkJS-3-CMDTIMEOUT Crnd timed out CCB slot and code
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CBUS-3--CORR Controller wrote read bc dci_memtest
Explanation hardware component failed an internal diagnostic test
Recommended Action Replace the malfunctioning device
Error Message %CEUS-3-CTRACHECK UniL Adapter Check Error
Explanation The Token Ring monitor firmware detected fatal error on the interface card
Recommended Action Issue clear interface command If this error recurs copy the
error message exactly as it appears and contact your technical support representative for
assistance
Error Message %CBUS-3 -CTRCNDFAILED Unit CPR Coirgnand Failed
Explanation command from the system to the Token Ring interface failed to complete
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
48 System Error Messages CBUS Error Messages
Error Message %CBUS-3--CTRCMDFAILED2 Unit CTR Command Failed Code
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CBUS-3-CTRINIT Unit CTR Initialization Failed
Explanation The Token Ring interface failed its internal self-tests
Recommended Action Issue clear interface command If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %CBUS-3--CTRLRCMDFAILO Controller cmd tailed count
Explanation command sent from the system to an interface processor failed to complete successfully
Recommended Action The system recovered by generating an error code to the requester
Error Message %CBUS-3-CTRLRCMDFAIL1 Controller cmd failed count
Explanation command sent from the system to an interface processor failed to complete successfully
Recommended Action The system recovered by generating an error code to the requester
System Error Messages 49 CBUS Error Messages
Error Message %CBUS3-CTRLRINITERR Controller Error cdb chus_init
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CBUS-3-CTRRAMfEST Unit RAM Addressing Test Failed
Explanation The Token Ring interface failed its memory diagnostic tests
Recommended Action Issue clear interface command If this error recurs copy the
error message exactly as it appears and contact your technical support representative for
assistance
Error Message %CEUS-3-CTRRESET Unit Error %-04x cbustokets_reset
Explanation The Token Ring interface fajled to complete command that is part of the
reset sequence
Recommended Action Issue clear interface command If this error recurs copy the
error message exactly as it appears and contact your technical support representative for assistance
Erroi Message %CBUS-3 -CPRUCRECK Unit Microcode Check Error
Explanation The CTR microcode detected an unrecoverable error
Recommended Action Issue clear interface command If this error recurs copy the
error message exactly as it appears and contact your technical support representative for assistance
50 System Error Messages CBUS Error Messages
Error Message %CBUS-3 -DAUGHTER Unit daughter controller failed test interface disabled
Explanation hardware component failed an internal diagnostic test Test output and descriptions of ranges follow
Unit ranges 0-14
Indicates the Multibus jumper setting for the ciscoBus controller or in the Cisco 7000
slot number
daughter controller ranges 0-3
Indicates the ciscoBus relative slot number to or in the Cisco 7000 to of the
daughter card that failed the test
failed test memd read memcl write
If the failed test was inemd read the processor was able to write to shared ciscoBus buffer
but unable read back that memory from the ciscoBus registers was to memory through
special commands to the daughter card
If the failed test was memd write writes to the memory device through the daughter card
were not verified successfully with reads through the ciscoBus controllet
The daughter card under test responds successfully to some commands otherwise the
software would have received DAUGHTER_NO_RSP message but its memory device
tests failed The daughter card must be able to write to some memory device addresses
otherwise it cannot respond to any commands
Recommended Action First check that the daughter controller card is properly seated in
its Multibus and ciscoBus connectors Next swap daughter cards and check whether the
error follows the daughter card or the slot If the message recurs call your technical support
representative for assistance
System Error Messages 51 CBUS Error Messages
Error Message %CBUS3-DAUGHTERJrO_RSP Unit daughter not responding disabled
Explanation hardware component failed an internal diagnostic test Test output and
descriptions of ranges follow
Unit ranges 0-14
Indicates the Multibus jumper setting for the ciscoBus controllet
daughter controller ranges 0-3
Indicates the ciscoBus relative slot number to or in the Cisqo 7000 to of the
daughter card that failed the test
The daughter cards hardware was recognized across the ciscoBus backplane but the
daughter card did not respond to the first command issued to it
This condition is result of one of the following the daughter card did not reset or the the microcode on the card is in hung state or the card cannot fully communicate across
ciscoBus backplane cannot read or write shared MEMD or does not get the
the MALU_AflENTION signal across ciscoBus
Recommended Action First make sure that the daughter card is properly seated in its
Multibus and ciscoBus connectors If this action does not solve the problem call your
technical support representative
Error Message %CBUS-3--FCICt4DFATLO Controller cmd failed Ox%-04x count
Explanation command sent from the system to an interface processor failed to
complete successfully
Recommended Action The system recovered by generating an error code to the
requestet
52 System Error Messages CBUS Error Messages
Error Message %CBUS-3---FCICNDFAIL1 Controller cmd Ox%-OSx failed Ox%-04x count
Explanation command sent from the system to an interface processor failed to complete successfully
Recommended Action The system recovered by generating an error code to the requester
Error Message %CBUS-3-FDDIRSET Interface Error -fddi_reset
%CBUS-3--FDDIRSETU Unit Error fddi_reset
Explanation hardware device did not respond appropriately to request
Recommended Action Make sure the device is functioning and is configured correctly
Error Message %CBUS-3-FSIPRSET Interface Error fsip_reset
Explanation Fast Serial Interface Processor FSIP did not respond to reset request
from the route processot
Recommended Action Check FSIP electrical connections cable and ciscoBus
connections An FSIP microcode reload will be required If the check of electrical
connections reveals no problems and the message recurs call your technical support
representative for assistance
Error Message %CBUS-3-GHOST Attempted operation on missing hardware
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 53 CBUS Error Messages
Error Message %CBUS3-HSSIRSET Interface Error hssi_reset
%CBUS3-HSSIRSETU Unit Error hssi_reset
Explanation hardware component did not respond to reset command
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CBUS3-IN1TERR Interface Error cbus_init
Explanation The switch processor or ciscoBus controller signaled an error while
processing packet or selecting an interface This indicates software problem
Recommended Action Call your technical support representative
Error Message %CBUS-3-INTR Interface 1db cbus_interrupt
value Explanation The switch processor or ciscoBus controller returned nonsensical
Recommended Action Call your technical support representative
Error Message %CBUS-4-INTR Interface cbus_interrupt
Explanation hardware device did not respond appropriately to request
Recommended Action Make sure the device is functioning and is configured correctly
Error Message %CBUS-3-4EC_0UTHUNC Interf ace output hung
Explanation Output hung on ciscoBus Ethernet interface
Recommended Action Correct any problems with the Ethernet cable then manually
re-enable the port
54 System Error Messages CBUS Error Messages
Error Message %CBUS-3-MIPSPAT Out of buffers--losing status information for the NIP card
Explanation This ERROR results from CPU starvation typically caused by heavy fast switching activity The counts displayed for the MultiChannel Interface Processor MIP card are incorrect
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CBUS-3--MOJJULE Missing for
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CBUS-3-NOBUF Buffer allocation failure
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CBUS4-NOCOOKIE controller missing configuration data disabled
Explanation The controller type was derived from hardware probe The controller number indicates the ciscoBus relative slot numbet This is hardware error
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 55 CBUS Error Messages
Error Message %CBUS3-NONEMORY No memory or
Explanation The requested operation could not be accomplished because of low memory condition or an unseated card in the Cisco 7000
Recommended Action Reduce other system activity to ease memory demands Confirm
that all cards are properly seated If conditions warrant upgrade to larger memory
configuration
Error Message %CBUS-3-OtJTHUNC tx%c output hung %-04x
Explanation transmission attempt on an interface failed The interface might not be
attached to cable or there might be software problem
Recommended Action Check that the interfaces are all connected to the proper cables
that is not the problem call your technical support representative
Error Message %CBUS-4-OUTWJNG Interface output hung restarting cBus controller mci_output
Explanation ciscoBus controller took too long to respond to command and was
restarted by software
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance You might need to repair
or replace the controller
Error Message %CBUS-3-POLLFAIL Interface failed to respond debug info follows
Explanation Token Ring interface card failed to respond to periodic polling This can
indicate software or hardware problem
and Recommended Action Copy the debugging information exactly as it appears report of it to your technical support representative See CBUS-3-POLLFAILDAT for the syntax this message
56 System Error Messages CBUS Error Messages
Error Message %CBUS-3-POLLFAILDAT mt
Explanation This is the debugging information for the CBUS-3-POLLFAIL error
Recommended Action Copy the debugging information exactly as it appears and report it to your technical support representative
Error Message %CBUS-3-PORflYPE Unexpected interface type for port type
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CBUS-4-RSETFAIL Interface tailed to reseL properly in code
Explanation An interface reset command failed This may be software or hardware problem
and it technical Explanation Copy the error message exactly as it appears report to your
support representative
Error Message %CBUS3-RESEThXI Reset of removed interface
Explanation An interface reset was attempted on an interface that was removed from the
command to down removed router This message appears if you use the shutdown bring interface
Recommended Action Informational message only No action required
System Error Messages 57 CBUS Error Messages
Error Message %CBUS-3-SELECT Select error slot port error
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CBtJS-3-TESTFAIL Unit failed test interface disabled
Explanation hardware component failed an internal diagnostic test
Recommended Action Check switch settings on the interface cards Check for proper unit numbers Reset the cards Replace the malfunctioning device
Error Message %CBUS-3---TXALLOC Error tx_allocate cbus_init
Explanation hardware device did not respond appropriately to request
Recommended Action Make sure the device is functioning and is configured correctly
Error Message %CBUS-3--UNKENC Interface unknown encaps type l5ONESEC
Explanation packet was received from the CIP with an unknown encapsulation type
The packet will be dropped
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
58 System Error Messages CCP Error Message
CCP Error Message
Point-to-point Compression Control Protocol error message
Error Message %CCP4--NOBTJF Interface
Explanation Compression requested new data buffer for decompressing into and was
refused due to none being available for this interface
Recommended Action Use the buffers configuration command to increase the number
of buffers available on the interface that this occurred This should prevent repeat An
example of the commands you execute follows
You rBox YourBoxconf YourBox config YourBoxconfigbuffers bri max-free 12
CI Error Messages
Chassis Interface CI Cisco 75xx platform environmental monitor card error messages
Error Message %CI-3-BLOWER Blower failure
Explanation One of the routers cooling fans failed
Recommended Action Replace the fan as soon as possible or the roUter may shut itself
down or fail to operate properly
System Error Messages 59 Cl Error Messages
Error Message %CI-l-BLOWSHUT Blower failure shutdown in dec seconds
Explanation One of the six blowers in five-slot chassis has failed Because each blower
cools separate region of the cards in the chassis all blowers are needed for router
operation If blower failure persists for minutes the router will shut itself down and will
need to be power cycled
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message
%CI-6-BPL1ANE CI type differs from NVRAM type 11dec11
Explanation The chassis type as reported by the chassis interface is different from that programmed into NVRAM
Recommended Action Copy the errormessage exactly as it appears and report it to your
technical support representative
Error Message %CI4-COND Restarting with recent soft power failures
Explanation soft power failure also called soft shutdownoccurs when the router
shuts itself down because it has detected an overheating condition When the temperature
the cards shutdown but the increases past the board shutdown trip point are power
supplies fans and chassis interface continue to run
If the system then cools past the restart trip point the system restarts The system counts
the number of .soft shutdowns and decreases its soft reset counter accordingly from its
maximum value to prevent the cycle from repeating indefinitely If the counter reaches
zero the system undergoes hard shutdown which requires power cycle to recover from
The soft shutdown counter is reset to its maximum value after the system has been up for hours
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
60 System Error Messages Cl Error Messages
Error Message %CI-3-CTFLRTYPE Wrong controller type
Explanation The CI was manufactured incorrectly
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CI-2-ENVCRIT measured at
Explanation One of the measured environmental test points exceeds an extreme threshold
Recommended Action Correct the specified condition or the router may shut itself down
or fail to operate properly
Error Message %CI-4-ENVWABN measured at
Explanation One of the measured environmental test points exceeds the warning threshold
Recommended Action Closely monitor the condition and correct if possible If the
situation worsens call your technical support representative for assistance
Error Message %CI-3-NO_HSA HSA not supported in this release please remove one RSP2
Explanation Two Route Switch Processors RSPs are installed in the chassis The
software can support only one RSP
Recommended Action Remove one of the RSPs
System Error Messages 61 CI Error Messages
Error Message %CI-3--NOACK acknowledge failure cmd addr data
Explanation The CI software failed to communicate with the CI hardware
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CI-4-NOTFOIJND Chassis Interface not found
Explanation The system software could not detect the presence of CI card
Recommended Action Verify that the CI card is correctly installed in the backplane If
the error recurs call your technical support representative for assistance
Error Message %CI6-PSCHANGE Power supply changed from to
Explanation The CI reported that power supply was either installed removed or changed
Recommended Action If the situation does not correspond with physical change in the
systems power supplies call your technical support representative for assistance
Error Message %C1-3-PSFAIL Power supply failure
Explanation One of the routers power supplies failed
Recommended Action Replace the failed power supply as soon as possible
62 System Error Messages CLEAR Error Message
Error Message %CI3-SLOTCONP Inconsistent slot
Explanation The CI software detected possible inconsistency in the CII hardware
Recommended Action Confirm that the CII card is correctly and fully installed in the
backplane If error recurs call your technical support representative for assistance
CLEAR Error Message
Clear error message
Error Message %CLEAR-5-COUNTERS Clear counter on by
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CLNS Error Messages
051 Connectionless Network Service error messages
Error Message %CLNS-5-AJJCHANGE Adjacency to neighbor Id interface Up/flown reason
Explanation An Intermediate System-to-Intermediate System ISIS or NetWare Link
Services Protocol NLSP adjacency with neighboring router has either come up or gone
down The message describes the change and the reason for it This message appears only
if log-adjacency-changes command is configured for the ISIS or NLSP process
Recommended Action This message is primarily informational and appears normally as
routers and links go up or down Unexpected adjacency loss might indicate high error rates
or high packet loss in the network and should be investigated
System Error Messages 63 CLNS Error Messages
Error Message %CLNS-4-AREALOST Too many ISIS areas--cant route to area
Explanation Intermediate System-to-Intermediate System ISIS allows only three area
addresses per area Multiple routers with at least one area address in common merge all of
their configured area addresses into single set If the resulting set more than three area
addresses this message appears and indicates that there will be loss of connectivity to the
specified area
Recommended Action Reconfigure the network so that the area has fewer area
addresses or split the area into multiple areas
Error Message %CLNS4-BADPACKET from
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CLNS-l-BKUPERR ISIS in ndb_next ndb_prev isp_next lspprev metric index
Explanation An internal error occurred in the maintenance of the Intermediate
System-to-Intermediate System ISIS backup route table
Recommended Action Copy the error message exactly as it appears and copy down the
routers configuration along with any other relevant information Contact your technical
support representative for assistance
Error Message %CLNS-4-CKSUMERR LSP database checksum error restarting
Explanation hardware or software error occurred
the it and Recommended Action Copy error message exactly as appears report it to your
technical support representative
64 System Error Messages CLNS Error Messages
Error Message %CLNS-4---EDATFAIL Encapsulation failed dst
%CLNS-4-EESHFAIL Interface encapsulation of ESH failed HLEN
Explanation Either message can occur when an interface is down and static neighbor entry exists in the systemsCLNS routing table Jf this is not the case the message indicates an internal software error
Recommended Action Check the interface If the interface is not down and no static neighbor entry exists for that interface call your technical support representative for assistance
Error Message %CLNS-l--LINXERR ISIS in lsp_next isp_prey
index iier
Explanation An internal error occurred in the maintenance of Intermediate
System-to-Intermediate System ISIS or NetWare Link Services Protocol NLSP link-state packet LSP linkages
Recommended Action Copy the error message exactly as it appears and copy down the routers configuration along with any other relevant information Contact your technical
support representative for assistance
Error Message %CLNS-3-LSPCHAIN non-null pointer on treed LSP index
Explanation An internal error occurred in the Intermediate System-to-Intermediate
System ISIS or NetWare Link Services Protocol NLSP
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 65 CLNS Error Messages
Error Message %CTiNS-4-LSPCKSUM ISIS Bad level LSP LSP ID checksum received on interface bad count error count
%CLNS-4-LSPCKSUM NLSP Bad level LSP cLSP ID checksum received on interface bad count error count
Explanation link-state packet LSP was received for either Intermediate System-to-Intermediate System ISIS orNetWare Link Services Protocol NLSP which failed an internal data checksum but which passed the data-link checksum The interface
on which the LSP was received is indicated along with the total count of checksum errors
received the LSP ID and the level of the failing LSP This message usually indicates data
corruption occurring on link but might also indicate data corruption in memory in neighboring router
Recommended Action If the error is in neighboring routers memory the problem will
correct itself within 15 minutes That router will detect its internal error and regenerate the
corrupted data This case is usually indicated by single LSP ID appearing repeatedly in
these messages The same LSP ID might appear in this message on other routers as well
If data-link corruption has caused the error check the link for errors and deal with them
appropriately This case is usually indicated by number of different LSP IDs appearing in these messages
Error Message %CLNS-3-LSPDB Inconsistent LSPIX entry tsp index ixentry ixentry-lsp
Explanation An internal error occurred in the Intermediate System-to-Intermediate System ISIS or NetWare Link Services Protocol NLSP
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
66 System Error Messages CLNS Error Messages
Error Message %CLNS-4-LSPFULL LSP filled to capacity dropping routes 1OONEMIN
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CLNS-3-LSPIXARRMATCH LSPix entry rnismatchwith LSP LSP is entry
Explanation An internal error occurred in the Intermediate System-to-Intermediate System ISIS or NetWare Link Services Protocol NLSP
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CLNS-3--LSPIXARRNULL LSP1x entry should be null is
%CLNS-3--LSPIXHEAD LSPix head doesnt match first prey
Explanation An internal error occurred in the Intermediate System-to-Intermediate System ISIS or NetWare Link Services Protocol NLSP
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CLNS-4--LSPTOOBIG LSP size bigger than interface MTU LSP dropped lOONENIN
Explanation software or hardware error occurred
and it Recommended Action Copy the error message exactly as it appears report to your technical support representative
System Error Messages 67 CLNS Error Messages
Error Message %CU4S-3-NSAPES Invalid NSAP type in ES table or
%CLNS-4-NSAPIS Invalid NSAP type jn IS table
%CLNS-4-REDIRECT Redirect found for non-route entry dst next-hop
Explanation An internal software error occurred
Recommended Action If the message recurs call your technical support representative
for assistance
Error Message %CLNS3-ONLIST entry already threaded prAy next index ver
Explanation An internal error occurred in the Intermediate System-to-Intermediate
System ISIS or NetWare Link Services Protocol NLSP
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CLNS4-TENT
Explanation An internal error occurred in the Intermediate System-to-Intermediate
System ISIS or NetWare Link Services Protocol NLSP
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
68 System Error Messages CLS Error Message
CLS Error Message
Cisco Link Services error message
Error Message %CLS-3-CLSFAIL CLS Assertion failed
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CLSDR Error Messages
Cisco Link Services driver error messages
Error Message %CLSDR-3-ERBRTN failed error
Explanation An error was returned from Cisco Link Services CLSI to the destination
logical unit DLU because CLSI did not perform the action desired by the DLU
Recommended Action Refer to CLSJ software documentation for more information
about this error Report this error to your technical support representative
Error Message %CLSDR3-INCORRECTPORT Incorrect port pointer in UsapId
Explanation Cisco Link Services CLSI returned an incorrect port pointer in the USapID
Recommended Action Report this error to your technical support representative
System Error Messages 69 CLSDR Error Messages
Error Message %CLSDR-3-MSGERR couldnt get message
could Explanation The destination logical unit DLU not send correct message to
Cisco Link Services CLSI because the message was formed incorrectly CLSI will not
perform the desired action
Recommended Action Report this error to your technical support representative
Error Message %CLSJJR-3--NOCEP Cannot found cep in free pool
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CLSDR-3-NOCLSSERVER unable to start the Server process
Explanation Could not start the CLSDRIVER process possibly due to resource
problem The subsystem using CLSDRIVER does not work
Recommended Action Remove and then restore the destination logical unit DLU in the
this to technical configuration file and try and reboot the system Report error your support
representative
Error Message %CLSDPc-3-NODLUCREATE Cannot create DLU for this type
Explanation The CLSDRIVER does not understand the destination logical unit DLU
type Currently only STUN uses the CLSDRIVER Any other value results in an error
Recommended Action Make note of all details associated with this error message and
report them to your technical supi3ort representative
70 System Error Messages CLSDR Error Messages
Error Message %CLSDR-3-NOINIT CLSDRIVER not initialized
Explanation CLSDRIVER initialization failed earliét Trying to use the driver now results in an error condition
Recommended Action Remove and then restore the destination logical unit DLU in the
file and and reboot the this to technical configuration try system Report error your support representative
Error Message %CLSDR-3-NOPORTCREATE Cannot create PORT structure
Explanation The CLSDRIVER cannot enable this port for processing
Recommended Action Try rebooting the router Report this error to your technical support representative
Error Message %CLSDR-3---NOREI4OVECEP RemoveCep Cep not on list
Explanation The destination logical unit DLU is trying to remove nonexistent connection end point from the internal data structure This creates problem in the connection end point CEP maintenance logic
Recommended Action Report this error to your technical support representative
Error Message %CLSDR3--NOREMOVEPORT RemovePort port not on list
Explanation The destination logical unit DLU is trying to remove an nonexistent port from the list of active ports because it does not have the correct list of active ports
Recommended Action Report this error to your technical support representative
System Error Messages 71 COMP Error Messages
Error Message %CLSDR3--WRONGMSC Should never be here cis message type unknown
The is unknown the destination unit Explanation CLS message type to logical DIM
Recommended Action Report this error to your technical support representative
COMP Error Messages
Compression error messages
Error Message %C0MP-3-CONFIGBAD Interface Compression internal configuration error
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %COMP-5-NOBUF Interface
Explanation Interface serialO compression getbuffer failed causing Link Access Procedure Balanced LAPB retransmissions
Recommended Action Configure additional large and big buffers
72 System Error Messages COMP Error Messages
Error Message %COMP3-NOMEMORY No memory to decompress packet on interface
Explanation The router is attempting to decompress an incoming packet but no memory is available for the decompression The packet will be dropped The rare occurrence of this message should not be of great concern
this condition Recommended Action These actions can help to rectify
Turn off compression
Reduce the number of compressed interfaces or virtual circuits on the router
Reduce the clock rates on compressed interfaces
Upgrade the router with more memory faster processor or both
Error Message %COMP-3-SIZEBAD Interface Decompression size error
%COMP3-SYNCBAD Interface Decompression sync error
%COMP3-VERSIONBAD Interface Compression Version mismatch expected received
Explanation One interface is configured for predictor compression the other is not
Recommended Action Configure both interfaces for predictor compression
System Error Messages 73 CONTROLLER Error Messages
CONTROLLER Error Messages
Controller error messages
Error Message %CONTROLLER-2--CRASHED Interface Processor in slot not responding shutting it down
Explanation bontroller stopped responding to commands over the CBUS so it was put into shutdown mode
RecommendS Action Re-enable the controllers by issuing the no shut configuration
command on all controllers on the card or hotswap out the bad card and install the new one
You must still manually no shut the controllers
Error Message %CONTROLLER-2-FIRMWARE Controller
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CONTROLLjER2--NOTFOUND Controller not found for slot
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Eror Message %CONTROLLER-3--REMLOOP Controller remote loop
Explanation configurable controller entered remote loopback
Recommended Action No action required
74 System Error Messages CSC2 Error Message
Error Message %CONTROLLER-3-UPDOWN Controller changed state to
Explanation configurable controller changed its state
Recommended Action No action required
CSC2 Error Message
CPU card error message
Error Message %CSC2-4-BREAK AUX port hung because Transmit Break would not clear
Explanation The Universal Asynchronous Receiver/Transmitter UART in the console
serial interface is malfunctioning
Recommended Action Service the console serial port hardware
DBUS Error Messages
Data bus error messages
Error Message %DBUS-3-BADCTRLRTYPE Invalid controller type in slot
Explanation An interface processor responded with an unknown or illegal controller type
when queried This should not happen unless the running software does not support the
interface processor in question or the interface processor fails
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 75 DRUS Error Messages
Error Message %DEUS-3-BADEJ3PROM Invalid EEPROM data found for card in slot card disabled
Explanation The ID EEPROM on the indicated card is not programmed correctly
Recommended Action Call your technical support representative for replacement
Error Message %DBUS3-EADHSACONF Down rev RSP EPROM found HSA system upgrade EPROM or remove one RSP
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DBUS-3-DAUGHTER_STATS Slot control status
Explanation processor reported an error This message is sent out in conjunction with
other error messages to provide additional information
Recommended Action Call your technical support representative and report information
about all error messages displayed
Error Message %DEUS-3--DEUSINTERR Slot Internal Error
Explanation processor reported an internal errot The processor will be reset and not
used until the next DIR event or microcode download when it will be retested
Recommended Action Reinstall the processor or download the microcode If this error
recurs copy the error message exactly as it appears and contact your technical support
representative for assistance Currently no boards report this error
76 System Error Messages DBUS Error Messages
Error Message %DBUS3-DBTJSTIMOUT dbus not responding in slot
Explanation An interface processor failed to respond when queried for its controller type
This message indicates probable software or hardware problem
Recommended Action Copy the error message exactly as it appears and report it to your technical supp oil representative
Error Message %DBUS-3-CXBUSERR Slot CxBus Error
Explanation proëessor reported bus error The processor will be reset and not used until the next on-line insertion and removal OIR event or microcode download when it will be retested
Recommended Action Reinstall the processor or download the microcode If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %DBUS-3-NOMAC No system mac address foi.md in RP1 EEPROMI using interface mac address
Explanation You have either prototype or an RPI EEPROM that does not have the necessary block of MAC addresses
Recommended Action Replace the RN EEPROM Copy the error message exactly as it
appears and report it to your technical support representative
Error Message %DBUS3-NOMAGIC No magic number found in RP1 EEPROM
Explanation The structure containing the system MAC address needed by the QIR facility cannot be found in the RP BEPROM The RP must be returned for reprogramming
Recommended Action Return the RP for reprogramming and call your technical support representative for assistance
System Error Messages 77 DBUS Error Messages
Error Message %DBUS-3-NORESP bad or no response slot
Explanation board in the slot identified in the error message failed to respond
Recommended Action Record the output of the following commands
show version
show controllers cbus
show diag
shOw interface
show running config
Report this information to your technical support representative
Error Message %DBUS-3-SLOTCOMP Slot dIus error slot and complement do not rnat h
Explanation processor reported mismatch between the contents of the slot register
and its complement This condition indicates hardware failure in the diagnostic bus
controller on that processor or on the diagnostic bus The processor will be reset and not
used until the next OIR event or microcode download when it will be retested
Recommended Actign Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DBUS-3-SW_NOTRDY DBUS software not ready after elapsed status control
Explanation An interface processor failed to come online after being reset software or
hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
78 System Error Messages DBIJS Error Messages
Error Message %DBUS-3-IJNKNOWN Slot unknown controller type ignoring
Explanation processor reported controller type that is unknown to the systemThe processor will not be used and needs to be repaired
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %DBUS3--WCSCTRLREFtR Slot WCS Controller Instruction Error
Explanation The writable control store WCS is the set of devices on each interface processor that contains the running microcode It can be loaded either from the ROM on the interface processor or from the system by using the downloadable microcode facility In this message proccssor reported WCS controller instruction errot The processor will be reset and not used until the next OIR event or microcode download when it will be retested
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %D131J5-3-WCSERR Slot WCS controller in error state Oxhex resetting
Explanation The processor in the slot identified in the error message reported writable control store controller The will be reset and microcode WCS error processor new loaded This error message appears only when microcode is downloaded
Recommended Action If this message recurs after the processor is reset and new microcode is loaded call your technical support representative for assistance
System Error Messages 79 DBUS Error Messages
Error Message %DEUS3-WCSFLOW Slot flow cntrl error loading WCS last data Ox pos
%DBUS-3--WCSLDERR Slot error loading WCS status Ox cmd/data Ox pos
Explanation processor indicated an error condition while downloading microcode The
status cmd/data and pos numbers shown in the message reflect the error condition the last
byte of microcode loaded and the position in the file respectively If this error appears the
microcode download is abnormally terminated and the ROM microcode is loaded
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %DBIJS-3-WCSPARERR Slot WCS Controller Parity Error
Explanation processor reported WCS parity errot The processor will be reset and not
used until the next OIR event or microcode download when it will be retested
Recommended Action Replace the processor or download microcode If this error
recurs copy the error message exactly as it appears and contact your technical support
representative for assistance
Error Message %DBUS-3---XILINX ready wait timeout slot
Explanation The field-programmable gate arrays on an interface processor failed to load
after being reset This indicates probable software or hardware problem
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
80 System Error Messages DIALER Error Messages
DIALER Error Messages
Dial-on-demand routing DDR error messages
Error Message %DIALER-2-NOMEMORY No memory to send dialer kicker packet out interface
ii chars
Explanation The router is out of memory and cannot initiate dialer call to start the
snapshot active period
Recommended Action Check the memory usage of the router and report the problem to
your technical support representative
Error Message %DIALER2-NOSWILYB No software interface associated with hw intert ace
Explanation An internal software error occurred
Recommended Action Call your technical support representative and report the error
message the system version and the router configuration Use the show version
command to obtain the software version
DIRRESP Error Message
Director responder error messages
Error Message %DIRRESP-7-NQROtJTE no route for destination
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 81 DLC Error Messages
Error Message %DIRRESP-3-SUBNETTED unable to determine metric for subnetted
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
DLC Error Messages
Data-link control error messages
Error Message %DLC-3-BADPARAM Function value passed in parameter chars
Explanation An internal software error occurred
Recommended Action Call your technical support representative and report the error message and the system version Use the show version command to obtain the software version
Error Message %DLC-3-INVPCEP Close Station invalid PCEP
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DLC-3-NOMEMORY no memory for
Explanation There was not enough free memory to complete the operation
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
82 System Error Messages DLC Error Messages
Error Message %DLC-4--OPTNULL Error NULL parameter unexpected
Explanation An internal software error occurred
Recommended Action Call your technical support representative and report the error message and the system version Use the show version command to obtain the software version
Error Message %DLC-3--WPUTERR default port type
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 83 DLSw Error Messages
DLSw Error Messages
Data-link switching error messages
Error Message %DLSWC-3-BADCLSI primitive not valid for dlsw
%DLSWC3-BADCLSICNF Invalid confirm
%DLSWC-3-BADCLSIDATALEM Bad data len
%DLSWC-3-BADCLSIHDRLEN Bad header len
%DLSWC-3-BADCLSIIDTYPE Invalid ID type
%DLSWC-3-BADCLSIIND Invalid indication
%DLSWC-3-BADCLSIPRIMTYPE Invalid primitive type
%DLSWC-3-BADCLSIRET Invalid ret code
%DLSWC-3-BADCLSISAP Bad cisi SAP Id
%DLSWC-3-BADDLCOP dlsw_action bad dlc event
%DLSWC-3-BADPEEROP bad peer op in peer_to_core dec
%DLSWC3-BADSSPEVENT dlsw_action bad ssp event
Explanation data-link switching system error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DLSWC-3-BADSSPHDR bad ssp hdr in proc ssp
Explanation Silicon Switch Processor SSP header received from the remote peer
contains errors in one of the fields
confirm that it Recommended Action If the remote peer is nonCisco router supports the DLSw RFC 1795 standard
84 System Error Messages DLSw Error Messages
Error Message
%DLSWC-3-BADSSPOP bad ssp op in proc ssp
Explanation Silicon Switch Processor SSP frame with an invalid command was received from the remote peer
Recommended Action If the remote peer is nonCisco router confirm that it supports DLSw RFC 1795 standard
Error Message %DLSWC-3-BMYIIMEROP dlsw_action bad timer event
Explanation data-link switching system error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DLSWC-3-FAILASSERT Assertion failed
Explanation An internal software inconsistency occurred The router continues to
operate
Recommended Action If this continues to recur record the entire message and note any
DLSw problems that you experience Provide this information to your technical support
representative
Error Message %DLSWC-3FOBKFAIL Cant fork process
Explanation DLSw process cannot run
Recommended Action Reduce other system activity to ease memory demands If
conditions warrant upgrade to larger memory If this message recurs copy the error
message exactly as it appears and report it to your technical support representative
System Error Messages 85 DLSw Error Messages
Error Message %DLSWC-3 FSMACTION
Explanation Indicates frames sent by DLSw on LAN or WAN side This is good
expected behaviot
Recommended Action Informational message only No action required
Error Message %DLSWC-3-FSMCALL state event
%DLSWC-3-FSMERR fsm error chars event
%DLSWC3-FSMINTERR fr em internal error
%DLSWC3-FSNONKERR event input states
%DLSWC3-INVALIDSTATE finite state machine in invalid state
%DLSWC3-INVALIDTIMER bad timer pop for new state
%DLSWC3-NOBUFF No buffer
%DLSWC-3-NODLSW no dlsw
Explanation data-link switching system error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DLSWC3-N0MEMBACK No memory to create circuit entries background
Explanation DLSw could not start new circuit because of low memory condition
demands If Recommended Action Reduce other system activity to ease memory
conditions warrant upgrade to larger memory configuration
86 System Error Messages DLSw Error Messages
Error Message %DLSWC-3--NONEMDLC No memory to create circuit entry from clic
%DLSWC-3-NOMEMSSP No memory to create circuit entry from ssp
Explanation data-link switching system error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %DLSWC-3-NOPARAN dlsw_action null param bik
%DLSWC-3--NOPEER no peer
Explanation data-link switching system error occurred
Recommended Action If this message recurs copy the error message exactly asit appears and report it to your technical support representative
Error Message %DLSWã3-RECVSSP SSP OP chars from
Explanation Silicon Switch Program SSP frame was received from the remote peer
Recommended Action Informational message only No action required
Error Message %DLSWC3-SENDSSP SSP OP
Explanation Silicon Switch Program SSP frame was sent to the remote peer
Recommended Action Informational message only No action required
System Error Messages 87 DLSw Error Messages
Error Message %DLSWP-3-PBAIJIJALUE DLSw invalid
Explanation bad parameter value was passed to function charsiinvalid parameter
chars with value This error should not cause any network problems unless it happens
repeatedly
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative as case problem
Error Message %DLSWP3-PCAPMISMATCH DLSw
Explanation Priority keyword was used on one router but not on the other The priority
keyword is an option on the DLSW remote peer definition If priority keyword is used one
router it must be used on the other
Recommended Action If you wish to use prioritization use it on both routers
Error Message %DLSWP3 -PGENERAL DLSW
Explanation general error condition was detected as described in the message text This
error should not cause any network problems unless it happens repeatedly
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative as case problem
Error Message %DLSWP3-.PNOMEM DLSw No memory to
Explanation The router ran out of system memory for operation as described in the message text Most likely the router image requires more system memory RAM than the router contains
Recommended Action Consult with your technical support representative about memory
requirements for specific image
88 System Error Messages DMA Error Messages
Error Message %DLSWP-3-PPASSIVE DLSw passive open failed from Ilinet
Explanation The system does not have enough main memory RAM for TCP to allocate
the data structures required to accept an incoming TCP connection Most likely the router
image requires more system memory RAM than the router contains
Recommended Action Consult with your technical support representative about memory
requirements for specific image
Error Message %DLSWP-3-PPRIMISMATCH DLSw
Explanation The priority option on the specified partnefs remote peer definition does not
match the priority option defined on the local remote peer definition This is
configuration eiror
Recommended Action Check each remote peer statement and make sure use of the
priority option is consistent on both peers
DMA Error Messages
Direct memory access error messages
Error Message %DMA-1-BADICBPTR msgbadicbptr
Explanation An internal software error occurred
Recommended Action If this error message recurs copy it exactly as it appears and
report it to your technical support representative
System Error Messages 89 DMA Error Messages
Error Message %DMA-i-BADJUMPSTART DMA juinpstart failed
Explanation An anomalous situation where the direct memory access DMA jumpstart
mechanism failed to find the DMA to start
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DMA-l-BADLENGTH msg_badlength
Explanation VIP found that the memory device MEMD buffer header indicated zero
length transmit
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DMA-L-BADOWN msgjjadown
Explanation This message indicates that an unexpected own bit was found in DMA
entry
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
90 System Error Messages DNET Error Messages
DNET Error Messages
DECnet error messages
Error Message %DNET-3--HEARSELF Hello type for my address from via
Explanation The system is receiving its own DECnet packets Either serial line is
looped back or another host with the same DECnet address is already present on the LAN
Recommended Action Check the serial lines if present and the DECnet configuration
Error Message %DNET-4-MAPCON Map entry conflicts with adjacency to
Explanation Your DECnet configuration is incorrect host that is specified as nonlocal
is present on your local network
Recommended Action Correct the configuration Call your technical support
representative if you need assistance
Error Message %DNET-3-NOME24ORY No memory available for
Explanation The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If conditions warrant upgrade to larger memory configuration
System Error Messages 91 DNSIX Error Message
DNSIX Error Message
Department of Defense Intelligence Information System Network Security error message
Error Message %DNSIX3--NOBUFFER No buff er available for sending packet
buffer that Explanation The system tried to allocate but request was denied
Recommended Action Examine buffer usage statistics possibly more memory is required
DRPErrorMessage
Director Response Protocol error messages
Error Message %DRP-7--NOROTJTE no route for destination
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DRP-3-NOWRITE unable to send response to
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
92 System Error Messages DSPU Error Messages
Error Message %DRP-3-SUBNEflED unable to determine metric or subnetted
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
DSPU Error Messages
Downstream physical unit error messages
Error Message %DSPU3 -ActpuNegResponse ACTPU Neg rsp received from PU
Explanation Remote PU rejected the routers request for an SSCP-PU session
Recommended Action Verify Pt configuration parameters at the router and at the remote PU Determine whether the problem exists at the remote PU and correct it If the
problem persists call your technical support representative for assistance
Error Message %DSPU-3-CLslBadAdptCorrCLSI bad Adaptor correlator header
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears for assistance and contact your technical support representative
Error Message %DSPU-3-CLSlBadldentifier CLSI bad identifier header
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
System Error Messages 93 DSPU Error Messages
Error Message %DSPU-3--CLslBadldentifierPype CLSI bad identifier type header
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %DSPU-3-CLSlBadLength CLSI bad length header
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %DSPtJ-3-CLSlBadPrimitivecrud CLSI bad primitive command header
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %DSPU-3-CLSIBadPrimitiveIpe CLSI bad primitive type header
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %DSPU-3-ChSlBadReturncodeCLSI bad return code %d header
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
94 System Error Messages DSPU Error Messages
Error Message %DSPU-3 -CLslUnexpctActsapcnf CLSI unexpected Activatesapcnf header
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %DSPU3 -CLslUnexpctDeactSapcnt CLSI unexpected Deactivatesapcnf header
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message
%DSPU-3-CLSlUnexpctEnableCnf CLSI unexpectedEnablecnf header 11
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %DSRJ-3-CLSlUnexpctldstnlnd CLSI unexpected IdStnlnd header
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
System Error Messages 95 DSPU Error Messages
Error Message %DSPU-3-DsPQBufferCorrupted DSPU could not free buffer buffer corrupted
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %DSPU-3-LSConrilnFailed Connect in from remote MAC lichars failed
Explanation Connection with remote station could not be established
Recommended Action Verify configuration parameters at the router and at the remote
station Determine whether the router is configured to accept connectln from this remote
station
Error Message %DSPU3-LSConnlnFaihedNoMem Connect in from remote MAC failed insufficient memory
Explanation Connection with the remote station could not be established because of insufficient memory in the routet
Recommended Action Correct low memory problem in the router If the problem
persists call your technical support representative for assistance
Error Message %DSPtJ-3-LSConnInFromHostFailed Connect in from host with remote MAC failed
Explanation Connection with the remote host could not be established
Recommended Action Verify host configuration parameters at the router and at the host
Determine whether the router is configured to accept connectln from this host
96 System Error Messages DSPU Error Messages
Error Message %DSPU-3-LsConnlnFromPuFailed Connect in from Pu with remote MAC failed
Explanation Connection with the remote PU could not be established
Recommended Action Verify PU configuration parameters at the router and at the remote PU Determine whether the router is configured to accept connectin from this remote PU
Error Message %DSPU-3-LSConnOutToHostFailed Connect out to host failed
Explanation Connection with the remote host could not be established
Recommended Action Verify host configuration parameters at the router and at the host
Determine whether the host is active and responding to connection requests
Error Message %DSPU-3-LsConnOutToPuFailedConnect out to pu failed
Explanation Connection with the remote PU could not be established
Recommended Action Verify PU configuration parameters at the router and at the remote PU Determine whether the remote PU is active and responding to connection
requests
Error Message %DSPU-3-LslnvalidMaxlFrame Connection attempt failed from XID Invalid MaxlFrame
Explanation An invalid MaxlFrame value in an exchange identification XID was
received from the remote station connection with remote station could not be established
Recommended Action Correct link station configuration at the remote station
System Error Messages 97 DSPU Error Messages
Error Message %DSPU3-LSlnvalidwindowsizeConnection attempt failed from XIIIJ Invalid Windowsize
Explanation An invalid WindowSize value in an exchange identification XID was
received from the remote station connection with remote station could not be established
Recommended Action Correct link station configuration at the remote station
Error Message %DSPU3-LSNoACTPtJCapabilityConnection attempt failed from XID ACTPU not supported
Explanation The remote station did not request PU 2.0 activation connection with remote
station is terminated
Recommended Action Correct link station configuration parameters at the remote
station to request system services control point SSCP-PU session with the router
Error Message %DSPU-3---LSXlflNegotiationError XID received with CV 22 bad byte bad bit
Explanation XJD3 with an error indication was received from the remote station
connection with the remote station could not be established
Recommended control 22 Action Determine from the vector CV byte or bit
information which field in the XID3 is rejected by the remote station and correct the link
station configuration parameters at either the router or the remote station
98 System Error Messages DSPLJ Error Messages
Error Message %DSPU-3-NotifyNegRsp LU received Notify Neg Resp from host
Explanation Remote host rejected the routers request.to activate/deactivate an SSCP-LU session
Recommended Action Verify host configuration parameters at the router and at the remote host Determine whether the problem exists at the remote host and correct it lithe problem persists call your technical support representative for assistance
Error Message %DSPU3-SnaBadflata Bad SNA data received from PU data
Explanation Unrecognized SNA data was received from the remote PU
Recommended Action Correct the problem at the remote PU If the problem persists call your technical support representative for assistance
Error Message %DSPU-3-UnknownXidXID Format not supported XID
Explanation Unsupported XID received from the remote station connection with remote station could not be established
Recommended Action Configure the remote station to send supported XID if possible
Supported XID formats are
XID Format
XID Format
System Error Messages 99 DSX1 Error Messages
DSX1 Error Messages
Channelized El Europe and Ti US DSX-l telephony standard error messages
Error Message %DSX1- -NOMEMORY msgtxt_nornemory
%DSX1-l-NOMEMORY Unit no memory for
Explanation The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands Tf
conditions warrant upgrade to larger memory configuration
Error Message %DSX1-3 -BADENCAP msgtxt_badencap
%DSX1-3-BADENCAP Unit bad encapsulation in idbenctype
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assjstance
DUAL Error Messages
Enhanced Interior Gateway Protocol error messages
Error Message %DUAL-3-ANCHORCOtJNT Anchor count negative
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
100 System Error Messages DUAL Error Messages
Error Message %DUAL-3-BADCOUNT Route chars successors rdbs
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %DUAL3--BADStJNNOTIFY Dual notified us about summary
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %DUAL-6-EVENT
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %DUAL-3-INTERNAL Internal Error
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 101 DUAL Error Messages
Error Message %DUAL3-LINKSExIST Interface is going down and links exist
Explanation An interface is going down or is being removed from routing through JGRP
but not ail links neighbors have been removed from the topology table
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DUAL3--LINKSTILLUP Link still exists on
Explanation hardware or software error occurred
ReOommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DUPL3-MULTIFLOW Flow control error on
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DUAL-5-NBRCHANGE Neighbor is
Explanation neighbor came up or went down
Recommended Action No action is required
102 System Error Messages DUAL Error Messages
Error Message %DUAL-3-NOBUFFER No buffers available for byte packet
Explanation The DUAL software was unable to allocate packet buffer The system may be out of memory
Recommended Action Record the output from the following commands show proc mem repeated twice show memshow buffers show version write terminal Provide this information to your technical support representative
Error Message %DUAL-3-NOHfl4DLE Handle is not allocated in pool
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %DUAL-3-NOMATCH Nexthop and infosource dont match
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %DUAL-3-NOMEMORY No memory available for
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 103 DUAL Error Messages
Error Message %DUAL-3-NOSQCKET Unable to open socket for AS
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DUAL-3-PEERSEXIST peers exist on 11DB
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DUAL-3-PROBESEQ Bad probe sequence from expecting
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DUAL-3---RDBLEFT Lingering DRDB deleting 11DB dest nexthop origin
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
104 System Error Messages DUAL Error Messages
Error Message %DUAL-3-REFCOUNT Negative refcount in pakdesc
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %DUAL-3-SIA Route stuck-in-active state in Cleaning up
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %DUAL-3-SIANOHZNDLE Stuck-in-active and unallocated handle in reply-status table Cleaning up
Explanation hardware or software error occurred
and it Recommended Action Copy the error message exactly as it appears report to your technical support representative
Error Message %DUPL-3-UNKTIMER Unknown timer type expiration
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 105 DVMRP Error Messages
DVMRP Error Messages
Distance Vector Multicast Routing Protocol DVMRP error messages
Error Message %DVMRP-1-BADNASK Bad mask received from lint Report ignored
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DVMRP-1-ROUTEHOG Receiving routes from in the last
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
EGP Error Messages
Exterior Gateway Protocol error messages
Error Message %EGP-3-NOPDB No pdb for
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
106 System Error Messages ENV Error Messages
Error Message %EGP-3-TOOBIG Insufficient buffering for update message
Explanation An EGP update message was too large to fit into single buffer
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
ENV Error Messages
Environmental monitor card error messages
Error Message %ENV-2-FLOW Air flow appears marginal
Explanation temperature reading indicates poor air flow
Recommended Action Attempt to resolve the air flow problem If the problem is not
resolved call your technical support representative for assistance
Error Message %ENV-l-SHUTDOWN Environmental Monitor initiated shutdown
Explanation One of the environmental measurements reached SHUTDOWN status The
system is about to shut down the processor to prevent damage to the hardware
Recommended Action Attempt to resolve the temperature problem If the problem is not
resolved call your technical support representative for assistance
Error Message %ENV-2-TEMP Ambient temperature measured Shutdown at
Explanation The ENV card indicates the temperature it measured and the temperature at
which it shuts down
Recommended Action Attempt to resolve the temperature problem If the problem is not
resolved call your technical support representative for assistance
System Error Messages 107 ENVM Error Messages
Error Message %ENV2-VOLTAGE testpoint measured Shutdown margin is
Explanation The ENV card indicates which voltage it is measuring for example 12 12 the amount of voltage that it measured and the voltage at which the processor will shut down the system
Recommended Action Attempt to resolve the voltage problem If the problem is not
resolved call your technical support representative for assistance
ENVM Error Messages
Environmental monitor error messages for the Cisco 7000 series
Error Message %ENVM-2-FAN Fan array has failed shutdown in minutes
Explanation There might be hardware problem with the fan array If the error condition
continues for two minutes the router automatically shuts down to prevent damage to router components
Recommended Action If the system shuts down replace the fan tray Copy the error
message exactly as it appears and report it to your technical support representative
Error Message %ENVM-2-FANOK Fan array has recovered
Explanation One or more of the variable speed fans on the 7010 recovered from prior
failure
Recommended Action Informational message only No action required
108 System Error Messages ENVM Error Messages
Error Message %ENVM-l-SHIJTDOWN Environmental Monitor initiated shutdown
Explanation The system reached SHUTDOWN temperature level and the router is being shut down to avoid any damage
Recommended Action Attempt to resolve the temperature problem If the problem is not resolved call your technical support representative for assistance
Error Message %ENVM-2-SUPPLY Power Supply is Non-Operational
Explanation power supply is not working or is not turned on
Recommended Action Check that the power supply is turned on if it is turned on and still does not operate call your technical support representative for assistance
Error Message %ENVM-2-TEMP temperature has reached level at
Explanation The temperature parameter shown reached warning or critical level and is approaching or approached condition that is outside the acceptable range
Recommended Action Attempt to resolve the temperature problem If the problem is not resolved call your technical support representative for assistance
Error Message %ENVM-2--VOLTAGE volts has reached level at
Explanation The voltage parameter shown reached critical level and is now out of specification
Recommended Action Verify the failure and call your technical support representative for repair or replacement
System Error Messages 109 ETHERNET Error Messages
ETHERNET Error Messages
C1000 series Ethernet error messages
Error Message %ETHERNET- -NOMEthORY msgtxt_nomemory
Explanation Insufficient memory exists to allocate the necessary memory pools
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %ETRERñETl-TXERR Fatal transniit error Restarting..
Explanation fatal transmit error occurred on the Ethernet line causing the line to be restarted
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
FDD1 Error Messages
Fiber Distributed Data Interface error messages
Error Message %FDDI-3-BADMUL Unit Cant set FDDI mac address to hardware multicast address
Explanation Part of your FDDI hardware failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
110 System Error Messages FDDI Error Messages
Error Message %FDDI3-BADSLOT Unit Slot does not exist
Explanation The main processor detects an invalid slot location for one of the network interface cards This should never happen
Recommended Action Call your technical support representative about obtaining replacement card
Error Message %FDDI-3-FDDIFAIL Interface
Explanation The FDDI interface failed
Recommended Action Save the output of the error message and call your technical
support representative for assistance
Error Message %FDJJI-3-FDDI Interface
Explanation The FDDT interface failed This is the second line of the preceding
FDDIFAIL message This line contains debug information
Recommended Action Save the output of the error message and call your technical
support representative for assistance
Error Message %FDDI-3-FDDIESET Interface Error -04x fddi_reset
Explanation FDDI-related command execution failure
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 111 FDDISTAT Error Message
Error Message %FDDI-3-FDDIRSETU Unit fdec Error -04x fddireset
Explanation FDDJ-related command execution failure
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %FDDI-3--NOCAM Unit No CAN exists for this interface
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
tcchnical support representative
Error Message %FDDI-1-NOMEMORY msgtxt_nomemory
Explanation The FDDI Management Information Base/Station Management MTB/SMT processing functions could not initialize due to insufficient memory
Recommended it it Action Copy the error message exactly as appears and report to your
technical support representative
FDDISTAT Error Message
Fiber Distributed Data Interface FDDI state error message
Error Message %FDDISTAT-4-STATtJS FDDI state detected on interface
Explanation An internal software error occurred
the error it it to Recommended Action Copy message exactly as appears and report your
technical support representative
112 System Error Messages FILESYS Error Messages
FILESYS Error Messages
Personal Computer Memory Card International Association PCMCIA Flash memory
card error messages
Error Message %FILEYS-5-PCMCIA_INSERT PCMCIA flash card is inserted into
Explanation Flash memory card was just inserted into slot or slot
Recommended Action Informational message only that indicates the card is there now
No action required
Error Message %FILESYS-5-PCMCIA_REMOVE PCMCIA flash card is removed from
Explanation Flash memory card was just pulled out of slot or slot
Recommended Action Make sure the removed card does not contain important files such
as the boot system image boot loader image system configuration file and so on Make
these checks before doing system reload
FLASH Error Messages
Flash nonvolatile memory error messages
Error Message %FLASH- -4ICCESSAflRIBONRP
Explanation The route processor cannot access the Flash memory cards attribute
memory The Flash memory card should continue to operate normally
Recommended Action If there is still problem with the Flash memory card copy the technical error message exactly as it appears and report it to your support representative
System Error Messages 113 FR Error Messages
Error Message %FLASH3-ERASEFAIL flash_erasefail_msg
Explanation The system was unable to erase Flash device
Recommended Action Try to erase again If that fails call your technical support
representative for assistance
Error Message %FLASH-3-WRITEFAIL f1ash_writefai1nsg
Explanation The write operatiomto Flash failed
Recommended Action Try erasing the device and trying the write again If that fails call
your technical support representative for assistance
FR Error Messages
Frame Relay error messages
Error Message %FR-5-DLCICHANGE Interface chars DLCI state changed to
Explanation The state of the Frame Relay PVC specified by the DLCI changed
Recommended Action Notification message only No action required
Error Message %FR-4-NAPERROR Interface remove maps or interface-dici command before change
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
114 System Error Messages GRIP Error Messages
GRIP Error Messages
Xerox Network Systems XNS Routing Protocol error messages
Error Message %GRIP-3-BADPATHS Invalid number of paths or
Explanation An internal inconsistency was detected in the XNS routing table structure
Recommended Action Note the parameters associated with this message and call your
technical support representative for assistance
Error Message %GRIP-2-BAJROTJTE Error route null table
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
HD Error Messages
HD64570 serial controller error messages
Error Message %HD-3-BADENCAP msgtxtjiadencap
%HD-1-B2DENCAP Unit bad encapsulation in idb--enctype
%HD-l-BAJRING Bad ring size
%BIJ-3-BADIJNIT Bad unit number
Explanation An internal software error occurred
for Recommended Action If message recurs call your technical support representative
assistance
System Error Messages 115 HD Error Messages
Error Message %HD-1 -BADLOOPCABLE rnsgtxt_badloopcahle
Explanation Loopback mode is not allowed when using an X.21 DTR cable on
Quad serial MM port
Recommended Action Do not enable loopback or use different cable type
Error Message %HD-l--BZDPORT
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message
%I-ID-l -BADPORTADAPTER
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %14D-O-INITFAIL Unit initialization timeout failure csr
Explanation The hardware failed to initialize correctly
Recommended Action Repair or replace the controllet
Error Message %HD5-LINEFLAP Unit excessive modem control changes
Explanation Too many modem control interrupts have been received The port was
disabled to prevent excessive use of the CPU
Recommended Action Check the cable on the serial port
116 System Error Messages HO Error Messages
Error Message %HD-1--MEMERR Unit memory error csrO
Explanation network serial interface detected hardware problem
Recommended Action Repair or replace the controller
Error Message %HD -NOMEMOR msgtxt_nomemory
Explanation The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If conditions warrant upgrade to larger memory configuration
Error Message %HDO--NOMEMORY Unit no memory for
Explanation The requested operation could not be accomplished because of low memory condition
demands If Recommended Action Reduce other system activity to ease memory conditions warrant upgrade to larger memory configuration
Error Message %HD-3--ODDSTART Interface Odd datagram start pak
%HD-3-OUTENCAP Unit bad output packet encapsulation
Explanation An internal software error occurred
Recommended Action If either of these messages recur call your technical support representative for assistance
System Error kiessages 117 HUB ErrorMessages
Error Message %HD-3-OWNERR Unit buffer ownership error
Explanation An Ethernet interface is malfunctioning or an internal software error occurred
Recommended Action Repair or replace the controller
HUB Error Messages
Cisco Ethernet hub error messages
Error Message %HUB-1-BADHUB Invalid hub type and number
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %HtJB-1-BAUUNIT Bad port number
Explanation An internal software error occurred
Recommended Action Copy the error message exactlyas it appears and report it to your
technical support representative
Error Message %HtJB- -NOMEMORY rnsgtxt_nornemory
Explanation The system detected that there is not enough memory for the hub
initialization
Recommended Action If conditions warrant upgrade to larger memory configuration
118 System Error Messages 1BM2692 Error Messages
Error Message %HUB-l-READERR Read op not allowed
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %HUE-l-WRITEERR Write op not allowed
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
1BM2692 Error Messages
Error messages which refer to an IBM Token Ring chip set
Error Message %IBM2 692 1-ADP_CHK msg_adaptor_check
Explanation hardware failure occurred The port is disabled
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %IB42 692-l-ICDB_PERROR msgjcdb_perror
Explanation hardware failure occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 119 1BM2692 Error Messages
Error Message %1BM26921INITFAIL msgjnitfail
Explanation hardware failure occurred The port failed to initialize
Recommended Action Copy the error message exactly as it appears and report it to your
technical supp oft representative
Error Message %1BM2692-1-NOPCIMEMORY msgnopcimernory
Explanation The router or access server could not allocate memory for the descriptors
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %IBM2 692 -1-NOSYS4EMORY msg_nosysmemory
Explanation The router or access server ran out of system memory
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %13M26921-PCI_PERROR msg_pci_perror
Explanation The protocol control information PCI bus failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %IHM2 692 -1--RX_HALT msgrxhalt
down Explanation The receiving RX channel has shut
Recommended Action The software should recover .Record the message for later reference
120 System Error Messages IGRP Error Message
IGRP Error Message
Interior Gateway Routing Protocol error message
Error Message %IGRP-3--NOSOCKET unable to open socket for AS
Explanation The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If
conditions warrant upgrade to larger memory configuration
IP Error Messages
Internet Protocol error messages
Error Message %IP-3-BADIPALIGN Invalid alignment in packet for IF
Explanation The packet data structure is misaligned This condition may result in small
amount of overhead in processing IP traffic
Recommended Action Enter show hardware command and report the output along
with this error message to your technical support representative
Error Message %IP-3-BADSROUTE Improper source route Length Ptr
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 121 IP Error Messages
Error Message %iP4-CLASS Bad IP address and mask in class_resolve %IP-3-DESTMOST src dst NULL desthost
Explanation An internal software error occurred
Recommended Action If either of these messages recur call your technical support
representative for assistance
Error Message IP-3--DESTHOST src dst NULL desthost
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %1P-4--DUPADDR Duplicate address on sourced by
Explanation Another system is using your IF address
Recommended Action Change the IF address of one of the two systems
Error Message %IP-3--LOOPPAK Looping packet detected and dropped \nsrc dsthltlprot sport dport \nin nexthop out \noptions ONEMIN
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
122 System Error Messages IP Error Messages
Error Message %IP-5-WEBINSTOMP Selected IP address
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %IP-5-WEBINST_KILL Terminating DNS process
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %IP-5-WEBINST_RESP Sending DNS response to request was for
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %IP-5-WEBINST_START Attempting web install from host
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 123 IPC Error Messages
IPC Error Messages
Interprocess Communication error messages
Error Message %IPC-2--CJNT_SEND Cannot send IPC message
Explanation An error occurred in the IPC slave discovery mechanism It might result in
malfunction in the operation of the IPC
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %IPC2-CONSTSTENCY Message failed consistency check
Explanation An internal inconsistency was found in some IPC data structures
Recommended Action Informational message only No action required
Error Message %IPC2--DELETED Attempt to deltte an IPC message second time
Explanation An internal inconsistency was found in some TPC data structures
Recommended Action Informational message only No action required
Error Message %IPC-2LOCK Lock done deleted element
Explanation An internal inconsistency was found in some IIPC data structures
Recommended Action Informational message only No action required
124 System Error Messages IPC Error Messages
Error Message %IPC-2-NOBTJFFER Could not fetch new message buffer
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %IPC-5-NODELFUNC Delayed mit function not available
Explanation The JPC application cannot be initialized because its initialization function does not appear in the TPC initialization function list
Recommended Action Copy the erior message exactly as it appears and report it to your technical support representative
Error Message %IPC-2-NODISPATCH Message from has no receive queue or dispatch routine
Explanation The IPC user failed to provide any means of handling the received message
Recommended Action Informational message only No action required
Error Message %IPC2-NOMEM No memory available for
Explanation The IPC protocol subsystem could not obtain the memory it needed
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 125 IPC Error Messages
Error Message %IPC-2-CNINT Called from interrupt level
Explanation The IPC user attempted prohibited call into IPC while IPC was running on
the interrupt stack
Recommended Action Informational message only No action required
Error Message %IPC-5-SLAVELOG VIPSLOT
Explanation The Cisco 105 software running on Versatile Interface Processor VIP
card generated this message The error message has been passed up to the Route Processor
or Route Switch Processor RP/RSP for display This message appears only if the user has
configured service slavelog
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %IPC-2-UNLOCK Unlock done on already unlocked element
Explanation An internal inconsistency was found in some IPC data structures
Recommended Action Informational message only No action required
Error Message %IPC_RSPJJBTJS-3 CABDERR
Explanation An IPC card has registered itself to the IPC master twice The card
malfunctioned and its IPC is not active
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
126 System Error Messages IPC Error Messages
Error Message %IPC_RSPJBUS-3-INVNUN
Explanation The IPC application tried to send message that was larger than IPC could handle The message was not transmitted
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %IPC_RSP_CBUS-3--NSGERR
Explanation The slave TPC cannot register with mastet It cannot exchange messages with the master
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %IPC_RSP_CBUS-3-NOBUF
Explanation The IPC ran out of memory device MEMD buffers
Recommended Action Reduce the number of applications currently running on the IPC
Copy the error message exactly as it appears and report it to your technical support representative
Error Message %IPQySP_CBUS-3-NOHWQ Hardware queue for card at slot not found
Explanation IPC messages cannot be transmitted due to missing hardware queue The messages were discarded and subsequent messages will not be transmitted to that card
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 127 IPFAST Error Messages
Error Message %IPCRSPCBUS-3-PROC
Explanation JPC processes cannot be created due to operating system errors The IPC will be inactive
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %IPC_RSFJBUS-3-SEATERR
Explanation The ID associated with an JPC card is either missing duplicated or cannot be created
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
IPFAST Error Messages
IP fast-switching error messages
Error Message %IPFAST-2-BADIF No support available for interface programming error 30ONESEC
Explanation programming error occulTed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
128 System Error Messages IPFAST Error Messages
Error Message %IPFAST-7-INTLEV Cache update request at interrupt level 5ONESEC
Explanation programming error occurred
Recommended Action Copy the error messageexactly as it appears and report it to your technical support representative
Error Message %IPFAST-6-INVALIDATE Cache invalidation occurring for ONESEC
Explanation The system is invalidating all cache entries for given interface
Recommended Action Informational message only No action required
Error Message %IPFAST-6-INVALREQ Cache invalidation request for
Explanation The system is invalidating all cache requests for given interface
Recommended Action Informational message only No action required
Error Message %IPFAST-4--RADIXDELETE Error trying to delete prefix entry for expected got
Explanation Problems related to the IP route cache triggered this debugging message
Recommended Action The router should correct for this error If the router cannot forward packets properly or is experiencing other problems copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 129 IPFAST Error Messages
Error Message %IPFAST-2--RADIXINIT Error initializing IP fast cache structures
Explanation programming error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %IPFAST-4--RADIxINsERt Error trying to insert prefix entry for expected got
Explanation Problems related to the IP route cache triggered this debugging message
Recommended Action The router should correct for this error If the router cannot
forward packets properly or is experiencing other problems copy the error message exactly
as it appears and report it to your technical support representative
Error Message
%IPFAST3-SANITY Found existing specific entry Lip mask when attempting to create
Explanation Problems related to the IP route cache triggered this debugging message
Recommended Action The router should correct for this error If the router cannot
forward packets properly or is experiencing other problems copy the error message exactly
it and as appears report it to your technical support representative
130 System Error Messages IPRT Error Messages
IPRT Error Messages
Internet Protocol routing error messages
Error Message %IPRT-3-BADCOMtIST Community list check with bad list 1OONESEC
Explanation user specified an invalid BGP community list number
Recommended Action Check the system configuration to make sure that the community
list specified falls within the valid range
Error Message %IPRT-2-COMPRESS Bad routecorupress call sdb
Explanation An internal software error occurred
Recommended Action If this message recurs call your technical support representative for assistance
Error Message %IPRT-3-NOMEMoRY No memory available for
Explanation The requested operation failed because of low memory condition
If Recommended Action Reduce other system activity to ease memory demands
conditions warrant upgrade to larger memory configuration
Error Message %IPRT-3PATHIDX Bad path index of for max ONEMIN
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 131 IPX Error Messages
Error Message %IPRT-3-TOOMANYNETS Too many networks in limit
Explanation Too many network subcommands have been entered for this routing
protocol
Recommended Action Advisory message only No action required
IPX Error Messages
Internetwork Packet Exchange error messages
Error Message %IPX-3-BADCOUNT Bad IPX server count
Explanation The internal SAP service count does not match the number of services
currently present and displayed by the show ipx servers command
Recommended Action You can report the problem to your technical support
representative but no corrective action is necessary
Error Message %IPX-3-BADIGRPSAP Cannot send incremental SAP update to peer on interface Increase buffers or increase output-sap-delay
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
132 System Error Messages IPX Error Messages
Error Message %IPx-3-BADIGRPSAPTYPE Unsupported SAP type for EIGRP being type
Explanation There are two types of service access points SAPs general queries and general responses This message is sent when you receive or attempt to send an SAP with
type code which is not general query or general response It is also sent when you receive general query not addressed to the broadcast address
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %IPX3--BADPATHS Invalid number of paths for
Explanation An internal inconsistency was detected in the IPX routing table structure
Recommended Action Note the parameters associated with this message If possible clear the IPX routing table by issuing the clear ipx route command This will result in lost connectivity until the routing table is rebuilt If the message recurs note the parameters
and call your technical support representative for assistance
Error Message %IPX-3--NOMEMORY Unable to allocate memory for
Explanation The system failed to allocate memory for an event The event variable will be one of the following procedures which attempts to allocate memory
SAP queue routing table SAP update
SAP update queue entry
RIP update queue entry SAP heap sort
pointer array RIP update
EIGRP process
route entry
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 133 ISDN Error Messages
ISDN Error Messages
Integrated Services Digital Network ISDN error messages
Error Message %ISDN6-CONNECT Interface is now connected to
Explanation This is an informational message It is sent when call is connected The
message displays the remote name and number which it receives from the Point-to-Point Protocol PPP authentication or from where the dialer placed the call to
Recommended Action No action is required
Error Message %ISDN5-DISCQNNECT Interface disconnected from call lasted seconds
Explanation This is an informational message It is sent when call is disconnected The
message displays the remote name and number which it receives from the Point-to-Point
Protocol PPP authentication or from where the dialer placed the call to It also shows how long the call lasted
Recommended Action No action is required
LANCE Error Messages
Local area network controller Ethernet interface error messages
Error Message %LANCE-4-BABBLE Unit babble error csrU
Explanation An Ethernet interface is malfunctioning
Recommended Action
Determine whether the malfunction stems from software or hardware error by turning off all fastswitching
134 System Error Messages LANCE Error Messages
Error messages showing that the packet is too large for the link indicate software error
at high level
Copy the error message exactly as it appears and report it to your technical support
representative
Receiving no error messages indicates hardware error
Repair or replace the controllet
Error Message %LANCE-3-BADBNCAP Unit bad encapsulation in idbenctype hex
%LANCE-3-BAIJUNIT Bad unit number
Explanation An internal software error occurred
Recommended Action If either message recurs call your technical support representative for assistance
Error Message TDR%LANCE5--COLL Unit excessive collisions
Explanation An Ethernet cable is broken or unterminated or the transceiver is unplugged
The time delay reffectometer TDR counter is an internal LANCE counter that counts the time in ticks of 100 ns each from the start of transmission to the occurrence of collision Because transmission travels about 35 feet per tick this value is useful to determine the approximate distance to cable fault
Recommended Action If the transceiver appears to be properly terminated repair or replace the Ethernet interface card
Error Message %LANCEi-INITFAIL Unit initialization timeout failure csr
Explanation The hardware failed to initialize correctly
Recommended Action Repair or replace the controller
System Error Messages 135 LANCE Error Messages
Error Message %LANCE-5-LATECOLL Unit late collision error
Explanation An Ethernet transceiver is malfunctioning the Ethernet is overloaded or the
Ethernet cable is too long
Recommended Action Repair or replace the controller
Error Message %LANCE-5-LOSTCARR Unit lost carrier Transceiver problem
Explanation An Ethernet transceiver is unplugged or faulty
Recommended Action Repair or replace the controllet
Error Message %LANCE-l-MEMERR Unit memory error csrO
Explanation An Ethernet interface detected hardware problem
Recommended Action Repair or replace the controller
Error Message %LANCE1-NOMEMORY Unit no memory for
Explanation The requested operation could not be accomplished because of low memory condition
to demands If Recommended Action Reduce other system activity ease memory
conditions warrant upgrade to larger memory configuration
Error Message %LANCE-3-OWNERR Unit buffer ownership error
Explanation An Ethernet interface is malfunctioning or an internal software error occurred
Recommended Action Repair or replace the controller
136 System Error Messages LANE Error Messages
Error Message %L1ANCE-3SPURIDON Unit spurious IDON intrrupt
Explanation An Eihernet interface generated spurious Initialization Done interrupt
Recommended Action Repair or replace the controller
Error Message %LANCE-3-IJNDERFLO Unit underf low error
Explanation The Ethernet hardware is requesting data faster than the system can supply
it This condition might indicate that the system is at the limitof its performance
Recommended Action small number of underfiows might not be cause for concern
You can monitor underfiows with the show interface command Reducing the load on the
router or installing higher-performancel router should alleviate this problem
LANE Error Messages
LAN emulation error messages
Error Message %LANE-3-BADILMI Unexpected ILMI event
Explanation An internal error occurred
Recommended Action This error should not occur Download the system error log then
call your technical support representative and provide the log the error message and the
router configuration
Error Message %LANE-3-BADNAME ELAN name must be 1-32 characters long
Explanation An emulated LAN ELAN name was entered in command that is longer
than 32 characters The LANE standard vl.O requires name that is 32 characters or less
in length
Recommended Action Re-enter shorter name
System Error Messages 137 LANE Error Messages
Error Message %LPNE-3-BADTYPE LAN Emulation supports only Ethernet type
Explanation The user specified Token-Ring-emulated LAN which is not currently
supported
Recommended Action Specify an Ethernet-emulated LAN Future software releases will
support Token Ring ELANs
Error Message %LANE-3--LANE_LESBUS_UP LES/BUS coming up from previous command
Explanation The lane server-bus command was reissued to start the LANE service
components while the router was trying to execute previously issued lane server-bus command
Recommended Action Wait for the initial lane server-bus command to either succeed or
fail The status of the server bus can be checked via the show lane server-bus interface
sub-interface name command The previous command can also be cancelled with the no
lane server-bus command If these steps fail to clear the problem issue the shutdown
command followed by no shutdown command cycle on the subinterface or on the whole
interface As last resort issue the no interface sub-intei face name command followed by
the shutdown no shutdown command cycle
Error Message %LANE-3-LANE_SIGLCHAIN not in chain
Explanation An internal error occurred while system routines were handling ATM
signaling messages for LANE
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
138 System Error Messages LANE Error Messages
Error Message %LANE-3 -IJNE_SIQERR
Explanation An internal error occurred while system routines were handling ATM signaling messages for LANE
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message
%LsPNE3-LANESIC_INV_MSG invalid rnsg received
Explanation An internal error occurred while system routines were handling ATM signaling messages for LANE
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LANE-3-LANE_SI@_INV_STATE invalid req in state
Explanation An internal error occurred while system routines were handling ATM signaling messages for LANE
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LANE-E--LECt
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 139 LANE Error Messages
Error Message %LANE-3-LEC_BADAD LEO unable to compute ATM address
Explanation The client cannot obtain an ATM address from the given configuration or
auto-assignment failed to get an ATM prefix from the switch
Recommended Action If you expect the switch to assign the prefix to the router check that the Interim Local Management Interface ILMI is functional and the switch has
prefix configured Otherwise confirm that the client has an address in the NYRAM
configuration
Error Message %LZANE3-LEC_CFG CFG_REQ failed LECS returned
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LjLNE-3-LEC CONTROL MEG Received bad control message on interface lOONESEC
Explanation The client received control message over one of its contro virtual channel connections VCCs that failed the header cheek
Recom mended Action This message indicates noninteroperable LANE configuration
server LANE server or LANE client implementation on the emulated LAN
Error Message %LANE-3-LEQERR 1OONESEC
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
140 System Error Messages LANE Error Messages
Error Message %LNE- -LEC_INFO
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LANE3-LEC JOIN JOIN failed LES returned
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LANE-3--LEC_LISTEN listen failed on
Explanation The client failed an attempt to listen on particular ATM address
Recommended Action Reconfigure the client ATM address It is conflicting with another component on the ATM Interface Processor AlP for the same ATM address
Error Message %LANE-3-LEC_SICNAL Unexpected SigAPI event lOONESEC
Explanation ATM signaling sent the client an unexpected message type
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LANE-4-LEc_STATE_ERROR State Event
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 141 LANE Error Messages
Error Message %LM6-LEc_TIMER Timer expired
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LANR3---LECS ERR
Explanation An internal consistency error occurred
Recommended Action Copy the en-or message exactly as it appears and report it to your
technical support representative
Error Message %LANE4-LECS_WARN
Explanation The LANE configuration server address could not be registered with or
dc-registered from the switch using Interim Local Management Interface TLMI
Possible causes
The switch prefix is not available
The address is not acceptable to the switch the prefix does not conform
The interface over which this operation should take place is down
The ILMI subsystem on the router is not completely initialized
Recommended it it Action Copy the error message exactly as appears and report to your
technical support representative
142 System Error Messages LANE Error Messages
Error Message %LANE3-LSV_ADDR elan unable to register LES/BUS ATM addr
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LINE3-LSV_BADAD interface elan ELAN name unable to compute ATM address
Explanation Software was unable to compute an ATM address based on the ATM address
template given The characters in chars see above display will be either BUS broadcast-and-unknown server or config server in the actual error message
Recommended Action Enter correct ATM address template for the LANE component BUS server or config server named in the error message
Error Message %LANE-3-LSV_CRASH interface elan ELAN name unrecoverable error
Explanation An internal error occurred
Recommended Action This error should not occui Download the system error log then and the call your technical support representative and provide the log the error message
router configuration
System Error Messages 143 LANE Error Messages
Error Message %LANE3-LSV_DUPATM interfaceelan ELAN name client duplicate ATM address registration ATM address
Explanation An attempt was made by the specified LANE client to register MAC
address and ATM address pair that duplicated an ATM address already registered to another
LANE client
Recommended Action Use the show lane server command to list the registered
addresses in the LANE server reporting the error ColTect one of the two LANE clients that
is trying in error to use the same ATM address
Error Message %LANE3-LSVUPID interface elan ELAN name duplicate LECID
Explanation An attempt was made to define two different server-direct PVCs both on the
same subinterfaee same LANE server and both for the same client LECID
Recommended Action Delete one of the lane PVC commands that has this duplicated LECID
Error Message %LANE3-LSVDUPMAC interface elan ELAN name client duplicate MAC address registration
Explanation An attempt was made by the specified LANE client to register MAC
address and ATM address pair that duplicated MAC address already registered to another LANE client
Recommended Action Use the show lane server command to list the registered
addresses in the LANE server reporting the enor Correct one of the two LANE clients that
is trying in error to use the same MAC address
144 System Error Messages LANE Error Messages
Error Message %LANE-4-LSV_LECID interface elan ELAN name LECIIDs exhausted lOONESEC
Explanation The LANE server specified has 65279 clients No more can be added
Recommended Action Change the configurations to avoid trying to have more than
65279 LANE clients on this servet
Error Message %LANE3-LSV_MCAST interface elan ELAN name unable to create MC group
Explanation An internal error occurred
Recommended Action This error should not occur Download the system error log then call your technical support representative and provide the log the error message and the router configuration
Error Message %LANE-3-LSV_NOREG interface elan ELAN name client unable to register MAC address
Explanation An internal error occurred
Recommended Action This error should not occur Download the system error log then call your technical support representative and provide the log the error message and the router configuration
Error Message %LANE-6-MAKE17 Created vcd PVC for config server access
Explanation The LANE software created PVC normally 0/17 for accessing the LANE configuration server
Recommended Action Informational message only No action required
System Error Messages 145 LANE Error Messages
Error Message %LANE-3-NAMECHG Attempt to chamge ELAN name
Explanation Both the LANB client and the LANE server/broadcast-and-unknown server
may have an emulated LAN name specified in the configuration via the lane server-bus and
lane client commands If both specify the emulated LAN name then the name cannot be
changed by re-entering just one of the commands
Recommended Action Use the no lane server-bus command to delete the
server/broadcast-and-unknown server or the no lane client command to delete the client
Then the other of the two commands can be re-entered with another emulated LAN name
Finally re-enter the deleted command with the new emulated LAN name
Error Message %LANE-3-NEWPREF interface elan ELAN name ATM address prefix
Explanation Entering new ATM address template for some LANE component caused
the specified LANE server or bus to drop all clients and restart
Recommended Action Informational message only No action required
Error Message %LANE-3-NOILMI ILMI service registration failed
Explanation The Interim Local Management Interface ILMI feature is not included in
the software build running on the router
Recommended Action Reload router with software that includes the ILMI feature
Error Message %LANE-3--NOINT interface still destroying old sub-interface
Explanation An attempt was made to create new subinterface while previous version
of the subinterface was still being destroyed
Recommended Action Wait minute and try again If failure still occurs try shutting
down the main interface Rebooting may be required to recover in extreme cases
146 System Error Messages LANE Error Messages
Error Message %LhNE-3-NOREGAThI interface cannot register ATM address with ILMI
Explanation An attempt to register the given ATM address with the ATM switch failed
This failure can occur because the ATM switch is down or misconfigured The registration will be retried
Recommended Action If the situation persists after number of attempts and the switch
of the switch and must be examined The most cause is up the configuration router likely is that ATM address being registered is not compatible with the parameters for example the ATM address prefix configured in the switch Correct the configuration
Error Message %LANE-3-NCVCD VCDs exhausted
Explanation When trying to create PVC 0/17 the router ran out of PVC resources
Recommended Action The number of PVCs can be increased with the atm maxvc command
Error Message %LZNE-3-PVCBAD interface elan ELAN name PVC vcd has no assigned
Explanation The characters in chars see above display will be either ATM address or
virtual circuit is created LECID This message is reported when permanent PVC
all command without the necessary information included in the lane pvc
Recommended Action Include lane pvc command with the information appropriate for the PVC
System Error Messages 147 LANE Error Messages
Error Message %LANE-3-PVCLECS Unable to create PVC
Explanation An attempt to create the named PVC failed The most likely reason is that PVC was defined on the same or another subinterface with the same virtual path
identifier-virtual channel identifier VPI-VCI pair but with different encapsulation or
usage type
Recommended Action Correct the configuration
Error Message %LANE-3REGSTATE JILMI event In state
Explanation An internal error occurred
Recommended Action This error should not occur Download the system error log then
call your technical support representative and provide the log the error message and the
router configuration
Error Message %LANE3-TYPECNG Attempt to change ELAN type
Explanation Both the LANE client and the LANE Server/BUS may have an ELAN type
specified in the configuration via the lane server-bus and lane client commands as either
Ethernet or Token Ring If both specify the type the type cannot be changed by re-entering
just one of the commands
Recommended Action Use the no lane server-bus command to delete the server-bus or
the no lane client command to delete the client Then the other of the two commands can
be re-entered with new type Finally re-enter the deleted command with the new type
Error Message %LANE-5-UPDOWN changed state to
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
148 System Error Messages LANMGR Error Messages
LANMGR Error Messages
IBM LAN Network Manager error messages
Error Message %LANMGR-4-BADRNGNUM Ring number mismatch on shutting down RPS
Explanation The router detected conflict in assigned ring numbers for the specified
Token Ring The Ring Parameter Server RPS function was shut down to prevent
potentially incolTect information from being sourced onto the ring
Recommended Action Check all bridges connected to this Token Ring and ensure that
they are using the same assigned ring number
Error Message %LANNCR-4-BADUPCALL Unexpected call from LLC2 for Bridge
Explanation An internal software error occurred
Recommended Action If this message recurs call your technical support representative
for assistance
Error Message %LANMCR-4-OLDTRAMON Cannot run RPS on Old TRAMON code
the functions for Explanation The software on this interface cannot support required LAN Network Manager
Recommended Action Call your technical support representative about firmware
upgrade for this interface card
System Error Messages 149 LAPB Error Messages
LAPB Error Messages
X.25 Link Access Procedure Balanced error messages
Error Message %LAPB4-CTRLBAD Interface Invalid control field
Explanation received FRMR reported frame with an invalid control code
Recommended Action Check the serial line and the devices attached to the line
Error Message %LAPB4-FPAMEERR Interface Frame error CF VS VR Reason
Explanation FRMR frame was received indicating that protocol violation was
detected The Reason field will be interpreted by generating INFOBAD CTRLBAD
N1TOOBIG or INVNR messages immediately after this message refer to the explanations for these messages for more information
Recommended Action The protocol will recover by resetting the service This will
disrupt any network service on top of LAPB for example X.25 virtual circuits will be
cleared Follow the recommended action for any error message following the FRTvIR
reports if service becomes unacceptable check the serial line and its attached devices
Error Message %LAPB4-ILNFOBAD Interface Info field not permitted
Explanation received FRMR frame reported that an information field was present in
frame where no information field is allowed
Recommended Action Check the serial line and the device attached to the line
150 System Error Messages LAPB Error Messages
Error Message %LAPE--4-INVNR Interface Invalid NR value
Explanation received FRMR reported frame with an invalid NR value
Recommended Action Verify that the equipment attached to the serial line is configured with the same value maximum number of outstanding frames
Error Message %LAPB-4-N1TOQBIG Interface NI too large
Expanation received FRMR reported an information frame that was too Jong
Recommended Action Verify that the equipment attached to the serial line is configured with the same Ni value Ni is in bits and includes the entire frame plus 16 bits of CRC
Howevei some equipment may require configuration in octets the omission of the two
CRC octets or the omission of the three octets of LAPB control information
Error Message %LAPB2-N0BIJF Interface no buffer available to
Explanation There was insufficient memory for the LAPB protocol engine to send message
Recommended Action This message is acceptable if it occurs infrequently because the
LAPB protocol is designed to handle loss of frames Frequent occurrences can cause disruption of service The system can be configured to ease memory demands or if conditions walTant the system can be upgraded to larger memory configuration
Error Message %LAPB-3--NOINPIDB Input 1db not set
%LAPB-3-NULLPAK Interface NULL packet ptr rur yr
Explanation An internal software error occulTed
Recommended Action If either of these messages recur call your technical support representative for assistance
System Error Messages 151 LAT Error Messages
LAT Error Messages
DEC Local Area Transport error messages
Error Message %LAT-3-BADDATA Tty Data pointer does not correspond to current packet %LJ\T-3--BUFFULL Tty data buff en full with count
Explanation An internal software error occurred
Recommended Action If either of these messages recur call your technical support
representative for assistance
Error Message %LAT-3-NOSYNC Tty Output data ptrs out of sync with byte count
Explanation An internal software error occurred
Recommended Action If this message recurs call your technical support representative for assistance
Error Message %DAT-3-NULLIDB Null 1DB pointer with destination
%LAT-3-QBSPACED Queue block at not found for NI connection
%LAT-3-REUSE Tty Attempt to re-use slot array empty fill
Explanation An internal software error occurred
Recommended Action If any of these messages recur call your technical support
representative for assistance
152 System Error Messages LEX Error Messages
LEX Error Messages
LAN extension error messages
Error Message %LEX-3-NOTSENT Serial line down not sent
Explanation The serial line went down and the specified command was not sent to the LAN Extender
Recommended Action Determine why the serial line went down For example was the
cable was pulled or the LAN Extender powered off The command will automatically be
re-sent once the serial interface is operational
Error Message %LEX-3-RC1v.IDNAK could not be processed by LAN Extender
Explanation The LAN Extender could not process the command from the host router
Possible causes are
The LAN Extender ran out of memory
The message from the host router is malformed
request to write flash occurred while the LAN Extender was busy writing flash for
previous request
The size of file to be downloaded is greater than the amount of flash memory available
Recommended Action If the command was copy tftp lex unit-number or copy flash lex
unit-nwnbe make sure that the correct file that is FLEX image file is specified Only caused single copy request can be handled at one time If the problem was by temporary out-of-memory condition on the LAN Extender re-enter the command
System Error Messages 153 LINEPROTO Error Message
Error Message %LEX-3-RCMDREJ could not be processed by LAN Extender
Explanation The LAN Extender did not recognize the code for the specified remote
command This might occur if the user is running old LAN Extender software with newer
host router software that has support for new LEX remote commands
Recommended Action Update the LAN Extender software
Error Message %LEX-3-TIMEOUT Retry count exceeded for
Explanation The host router re-sent the given message as many times as specified in the
lex retry-count command configuration variable without receiving an acknowledgment
from the LAN Extender At this point the host router gives up trying to send this particular remote command message
Recommended Action Use the LEDs on the LAN Extender to determine if it is
operational Confirm that the lex timeout configuration command is set appropriately for
the speed of the link
LINEPROTO Error Message
Line Protocol error message
Error Message %LINEPROTO5-UPDOWN Line protocol on Interface changed state to
Explanation The data link level line protocol changed state
Recommended Action Notification message only No action required
154 System Error Messages LINK Error Messages
LONK Error Messages
Data link error messages
Error Message %LINK-3-BADENCAP Interface Bad encapsulation code
Explanation The lower level software was unable to write MAC header for datagram
probable cause is configuration error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LINK3-BADETHER Interface Bad ethernet encap code
Explanation An internal software error occurred
Recommended Action If this message recurs call your technical support representative
for assistance
Error Message %LINK3-BADMACREQ Interface non-existent MACADIJR registry for link
to network level address to level address failed Explanation An attempt map MAC
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 155 LINK Error Messages
Error Message %LINK-2-BDVCALL Interface undefined entry point
Explanation An internal software error occurred The high-level system code tried to use
an unimplemented entry point with the virtual interface descriptor block 1DB drivei
Recommended Action If this message recurs call your technical support representative for assistance
Error Message %LINK-3-BOOUSENCAP msgtxt_badencap
Explanation serial interface has been configured with an unknown encapsulation
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LINK5--BOOTP address resolved by
Explanation An interfaces IP address was successfully learned dynamically through
BootP The first address is the learned IP address The second IP address is the IP address
of the BootP server that provided the information
Recommended Action No action required
Error Message %LINK4-BRIDGECONFLICT encapsulated EPIDU recvd from
Explanation FDDI interface running in nonencapsulating transparent mode detected an
FDDI bridge running in encapsulation mode on the same fiber This is an unstable situation
and should be corrected The incoming interface is displayed along with the FDDI MAC
address in standard form
Recommended Action Upgrade the errant interface to full transparent mode Copy the
error message exactly as it appears and report it to your technical support representative
156 System Error Messages LINK Error Messages
Error Message %LINX-5-CHANGED Interface changed state to
Explanation The interface hardware changed state
Recommended Action Notification message only No action required
Error Message %LINK-3-CQMPREG Interface non-existent decompression registry Packet dropped
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message
%LINK-4-FDDISTAT Interface FIJDI state detected
Explanation There was state change on the FDDI ring
and it Recommended Action Copy the error message exactly as it appears report to your technical support representative
Error Message %LINK-4-FDDIUNK unknown len
Explanation An unknown FDDI datagram was received
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 157 LINK Error Messages
Error Message %LTh1K-2-LINEST No linestate vector for
Explanation An internal software inconsistency occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LINK-4---NOMAC random default MAC address of has\n been chosen
Explanation An addressing inconsistency occurred
Recommended Action Make sure that this address is unique or specify MAC addresses
for commands such as novell routing that allow the use of this address as default
Error Message %LINX2--NOSOURCE Source icTh not set
%LINX-3--TOOBIC Interface Output packet size of bytes too big
%LINK-3TOOSMALL Interface Output packet size of bytes too small Changed to bytes
%LINK-2---UENCAP Unknown line encapsulation code
Explanation An internal software error occurred
Recommended Action If any of these messages recur call your technical support
representative for assistance
Error Message %LINK-5-PARP address resolved by
Explanation The Reverse Address Resolution Protocol RARP resolved an IP address
Recommended Action Notification message only No action required
158 System Error Messages LLC2 Error Messages
Error Message %LINK--3-REMLQOP Interface remote ioop
Explanation The interface entered or exited remote loopback
Recommended Action Notification message only No action is required
Error Message %LINK-5-SLARP address resolved by
Explanation The Serial Line Address Resolution Protocol SLARP resolved an IP address
Recommended Action Notification message only No action required
Error Message %LINK--3-UPDcMN Interface changed state to
Explanation The interface hardware went either up or down
Recommended Action If the state change was unexpected confirm the configuration
settings for the interface
LLC2 Error Messages
Logical Link Control type error messages
Error Message %LLC4-Tl_ERR LLC2 INCREASE LLC TIMERS
Explanation The Ti timer popped for an LLC2 session However the frame which is to transmission be retransmitted is still on queue inside the router awaiting over RSRB Frame Relay or other protocol If the retransmission occurs the LLC2 session will
probably fail due to N2 retry failures
the decreases the Recommended Action Increasing LLC2 acknowledgment timers
likelihood of failure In addition investigate sporadic congestion in routed network
System Error Messages 159 LNMC Error Messages
Error Message %LLC-2-tJNEXPECT LLC2 UNEXPECTED EVENT
Explanation An internal software error was found software component is trying to use
LLC2 structures that do not exist
Recommended Action Record the configuration and any information that would be
useful in recreating the error and call your technical support representative
LNMC Error Messages
LAN network manager system error messages
Error Message %LNMC-3-BADCLSI primitive not valid for 1cm
%LNMC-3-BADCLSICNF Invalid cont inn
%LNMC-3-BADCLSIDATALEN Bad data len
%LNMC-3---BADCLSIHDRLEN Bad header len
%LNMC-3--BADCLSUDTYpE Invalid ID type
%LNMC-3-BADCLSIIND Invalid indication
%LNMC-3-BADCLSIPRINTYPE Invalid primitive type
%LNMC3-BADCLSIRET Invalid ret code
%LNMC3-EADCLSISAP Bad clsi SAP id
Explanation LAN network manager system error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
160 System Error Messages LPD Error Message
LPD Error Message
Line printer daemon error message
Error Message %LPD-3-MANYLF Line tline packet has too many newlines to convert
Expanation An internal buffer did not have enough room to add all the necessary carriage
returns to packet of LPD data destined for printer configured with newline-convert
command This message is unlikely to occur with file containing valid data
Recommended Action Check the file being printed to see whether it contains valid
printable data
System Error Messages 161 M32 Error Message
M32 Error Message
High-Level Data Link Control HDLC controller error message
Error Message %M32 -1-NOMEMORY msgtxtnomemory
Explanation An error has occurred caused by lack of main memory lack of 110 memory or hardware failure
Recommended Action Use the show mcmory command to confirm that enough memory
is available If there is not enough memory you need to upgrade your router If the router
has enough memory then there is probably hardware problem Copy the error message
exactly as it appears and report it to your technical support representative
MAILBOX Error Messages
ChipCom mailbox error messages
Note All MAILBOX-class messages are generated in response to various conditions
arising from the use of mailbox implemented on partner port of the Cisco 2500 The
mailbox is used to pass administrative information between the router and the main management module of the partners platform
Error Message %MAILEOX-3-BADCFJIKSUN Checksum failed Expected calculated Ignoring PDU
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
162 System Error Messages MAILBOX Error Messages
Error Message %MAILBOX-3-BADDATA Bad data in thailbox test got expected
%MAILBOX-3-FLAGSTAT Timeout while waiting for FLAGSTAT status
%MAILBOX-3-INITPC2 Timeout waiting for P02 during initialization status
%MAILBOX3-INTERR Bad mailbox interrupt
%MAILBOX-3---MAILO2O Timeout while waiting for MAILO2O status
%MAILBOX-3-MAILFAIL Mailbox failed to initialize
%MAILBOX-3-P02 Timeout while waiting for P02 status
%MAILBOX-3-SPtJRINT Spurious mailbox interrupt MAILO2O not asserted
Explanation hardware problem was detected in ChipCom interface board
call technical Recommended Action If any of these messages recur your support representative for assistance
Error Message %MAILBOX-3-BADECHO Echo-response did not match echo-request
Explanation The data received from an ECHO_RESPONSE protocol data unit PDU did not match the original data provided in the ECHO_REQUEST Usually this message is seen during initialization and indicates catastrophic failure of the mailbox interface See
MAILB OX-3-INITFAIL for more information
Recommended Action Confirm the router module installation Make sure the software revision on the management module and the router module carrier card is up-to-date If the error persists call your technical support representative for assistance
System Error Messages 163 MAILBOX Error Messages
Error Message %MAILBOX3-BADPDU PDU of type received Invalid or unsupported Ignoring
Explanation The protocol data unit PDU received was valid but the type is not
supported in the current software implementation It will be ignored
Recommended Action Informational message only No action required
Error Message %MAIIiBOX-3INflFAJL Mailbox initialization failure Outgoing mailbox of line
Explanation catastrophic failure involving the initialization of the administrative
mailbox occurred The mailbox will be taken offline and remain in that state until router
module reset or system reload occurs At that time initialization will again be attempted
Note that the its to receive and forward functionality of the router that is ability packets
is not affected by this errot
Recommended Action Confirm the router module installation Make sure the software
revision on the management module and the router module carrier card is up-to-date If the
error persists call your technical support representative for assistance
Error Message %MAILBOX6-INITOK Mailbox initialization successful
Explanaflon This message is generated after router reload to indicate the mailbox was
successfully initialized
Recommended Action Informational message only No action required
Error Message %MAILBOX- -MBOXDEBUG
Explanation This message header is paired with general debugging messages used to
provide information about the functionality of the mailbox To enable mailbox debugging issue the command debug mailbox
Recommended Action Advisory message only No action required
164 System Error Messages MAILBOX Error Messages
Error Message %MAILBOX-3-NOECHO Echo-request timed out No response received Mailbox of line
Explanation An ECHORESPONSE was not received in the appropriate time after the generation of an ECHO_REQUEST This failure only occurs during mailbox initialization and indicates problem between the communication path of the router module and its carrier card
Recommended Action Confirm the router module installation Make sure the software revision on the management module and the router module carrier card is up-to-date If the error persists call your technical support representative for assistance
Error Message %MAILBOX-3-OFFLINE Icutgoing mailbox is off line Interrupt ignored
Explanation This message is generated when an attempt is made by the management module to communicate with an offline mailbox When it appears it indicates problem exists between the perceived state of the mailbox from the routers side versus the management modules side
Recommended Action Issue system-wide reset on the management module If the error persists call your technical support representative for assistance
Error Message %MAILEOX-7-ONLINE Incoming1Outgoing mailbox coming online
Explanation This message is generated only when mailbox debugging is enabled It provides information about the state of each incoming or outgoing mailbox
Recommended Action AdviEory message only No action required
System Error Messages 165 MCI Error Messages
Erro Message %MAILBOX7-READ Reading from oarrier
Explanation This message is generated only when mailbox debugging is enabled It
provides very low-level information about the incoming mailbox data stream
Recommended Action Advisory message only No action required
Error Message %MAILBOX3-TIMEOUT Intra-PDU timeout occurred on mailbox data
Explanation timeout occurred while sending or receiving the characters of protocol
data unit PDU The entire PDU will be ignored
Recommended Action Informational message only No action required
Error Message %MTCLBOX-7--WRITE Writing to carrier
Explanation This message is generated only when mailbox debugging is enabled It
provides very low-level information about the outgoing mailbox data stream
Recommended Action Advisory message only No action required
MCI Error Messages
Multiport Communications Interface error messages
Error Message %MCI-5-INPUIERR Interface excessive input error rate
Explanation The input error rate was so high that the interface was temporarily disabled
The interface will be automatically reenabled in 30 seconds
Recommended Action If this message recurs check the communication lines
166 System Error Messages MCI Error Messages
Error Message %MCI-4-NOCOOKIE MCI controller missing configuration data disabled
Explanation The configuration PAL is missing
Recommended Action TI this message recurs call your technical support representative br assistance
Error Message %MCI4NOKEEPALIVE Interface keepalive not sent
Explanation The requested operatiou could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If conditions warrant upgrade to larger memory configuration
Error Message %MCI5-OBSOLETE Obsolete MCI firmware cant route and bridge simultaneously
Explanation The firmware on your MCI controller card is out of date
Recommended Action Upgrade your MCI firmware
Error Message %MCI-4-RSETFAIL Interface failed to reset properly in code
Explanation hardware device did not respond appropriately to request This generally indicates hardware problem
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 167 MCI Error Messages
Error Message %MCI-3--RXINDEX Unit invalid RX index
Explanation The MCI did not answer Multibus request This generally indicates hardware problem
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %MCI-3-SETUPERR Unit Error on setup index controller mcLjnterrupt
Explanation hardware device did not respond appropriately to request This generally indicates hardware problem
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %MCI-4-TESTFAIL Unit failed test skipping
Explanation hardware component failed an internal diagnostic test
Recommended Action You need to replace the malfunctioning component Copy the
error message exactly as it appears and report it to your technical support representative
168 System Error Messages MK5 Error Messages
MK5 Error Messages
MK5025 serial controller error messages
Error Message %MK5-3-BADENCAP Unit bad encapsulation in idbenctype
%MK5-lBADRINC Bad ring size
%MK5-3-BADUNIT Bad unit number
Explanation An internal software error occurred
Recommended Action If either of these messages recur call your technical support
representative for assistance
Error Message %IvflK5l-INITFAIL Unit initialization timeout failure csr
%MK5-l--INIThTOPPRIM Unit initialization failure No CSR1_PPRIMJNIT_CCNF csrl
%MK5-l-INITUERR Unit initialization CSR1_UERR tailurecsrt
Explanation The hardware failed to initialize correctly
Recommended Action Repair or replace the controller
Error Message %MK5-5-LINEFLAP Unit excessive modem control changes
have been received The Explanation Too many modem control interrupts port was
disabled to prevent excessive use of the CPU
Recommended Action Check the cable on the serial port
System Error Messages 169 MK5 Error Messages
Error Message %MK5-l--MENERR Unit memory error csrO
Explanation network serial interface detected hardware problem
Recommended Action Repair or replace the controller
Error Message %NK5-1-NOMEMORY Unit no memory for
Explanation The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If
conditions warrant upgrade to larger memory configuration
Error Message %MKS-3-OJJDSTART Interface Odd datagrain start pak
%NK5-3-OUTENCAP Unit bad output packet encapsulation
Explanation An internal software error occurred
Recommended Action If either of these messages recur call your technical support
representative for assistance
Error Message %MK5-3-OWNERR Unit buffer ownership error
Explanation An Ethernet interface is malfunctioning or an internal software error occurred
Recommended Action Repair or replace the controller
170 System Error Messages MROUTE Error Messages
Error Message %NK5-3-PLOSTERR Unit provider primitive lost csrO csrl
%MK5-3-PPRlMERR Unit unexpected provider primitive csrO csrl
%MK5-3--SPURPPRIMERR Unit spurious provider primitive csrO esri
%MK5-3-UPRIMERR Unit user primitive error csrO csrl
Explanation network serial interface detected hardware problem
Recommended Action Repair or replace the controller
MROUTE Error Messages
Multicast route error messages
Error Message %MROUTE-4-RAJIXDELETE Error trying to delete multicast route entry for expected got
Explanation An error in the multicast routing table occurred route could not be deleted
from the routing table
Recommended Action Execute clear ip mroute command Determine whether the
router is low on memory If the problem persists copy the error message exactly as it
appears and report it to your technical support representative
Error Message %MROUTE-2-RACIXINIT Error initializing IP muiticast radix for
Explanation Insufficient memory is available to initialize the IP inulticast routing table
Recommended Action Record the output from the following commands show process memory repeated twice show memory show buffers show version and show running
config Provide this information to your technical support representative
System Error Messages 171 NETMGT Error Message
Error Message %tCUTE4-RADlXINSERT Error trying to add multicast route entry for expected got
Explanation An error in the multicast routing table occurred route could not be
inserted into the routing table
Recommended Action Execute clear ip mroute command Determine whether the
router is low on memory If the problem persists copy the error message exactly as it
appears and report it to your technical support representative
NETMGT Error Message
Network Management error message
Error Message %NEThGT-6--ALERT SNA LLC
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
NHRP Error Message
Next Hop Resolution Protocol error message
Error Message %NBIRP-3-NOBUFFER No buffer available for sending packet
Explanation The NHRP software could not allocate packet buffet The system may be out of memory
Recommended Action Record the output from the following eomthands show proc mem repeated twice show mem show buffers show version write terminal Provide
this information to your technical support representative
172 System Error Messages NIM Error Messages
MM Error Messages
Network interface module error messages
Error Message %NIM-2-BADSLOT Illegal reference to non-existent slot
%NIM-2-BADSUBtJNIT Illegal reference to non-existent subunit in slot
%NIM-2-DEADICHAINQ Attempted to manipulate uninitialized ichainQ in
%NIM-2-LOSTICHAINQ Couldnt find idb in ichainQ in
%NIM-2-NOHWADDRESS All hardware addresses have been allocated maximum of
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %NIM-2-BADNIMREV Unsupported version of NIM in slot Version
Explanation The indicated network interface module NIM is not supported because it is
not of the correct revision Certain platforms Cisco 4500 or Cisco 4700 for example
require some NIMs to be of minimum rev level
Recommended Action Upgrade the NIM to the proper level
Error Message %NIM-2-IJEAJDICHAINQ Attempted to manipulate uninitialized ichainQ in \n
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 173 OIR Error Messages
Error Message %NIM2-LOSTICHAINQ Couldnt find idb in ichainQ in
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %NIM2--tJNSUPNIM Unsupported NIM in slot
Explanation The indicated NIM is not supported on this platform
Recommended Action Remove the NIM
OIR Error Messages
Online insertion and removal error messages
Error Message %OIR6--INSCARD Card inserted in slot interfaces administratively shut down
in slot The Explanation The QIR facility detected newly inserted processor dec
inserted interface will be shut down until it is configured by the user or if an interface of
that type was previously configured it will be restored to its previous state
Recommended Action Informational message only No action required
174 System Error Messages OIR Error Messages
Error Message %0IR-3LCNGSTALL Long bus stall dec ms check for improperly seated cards
Explanation Something is preventing the CxBus or CyBus from operating The usual reason is an improperly seated interface processor
Recommended Action Make sure all interface processor cards are firmly seated If the problem reoccurs it may indicate hardware failure Copy the error message exactly as it appears and report it to your technical support representative
Error Message %OIR-6--NOEOIR hardware version 1.0 not capable of EOIR
Explanation An attempt was made to remove or insert card in system containing at and removal least one card that does not support enhanced online inseration BOIR
Recommended Action Upgrade to card that supports EOIR features If this does not
solve the problem contact your technical support representative for assistance
Error Message %OIR-6-REMCARD Card removed from slot interfaces disabled
removal of from slot The Explanation The OIR facility detected the processor En and marked removed The interfaces on that processor will be administratively shut down as removed interfaces routing table will be flushed of any routes through the
Recommended Action Informational message only No action required
System Error Messages 175 OSPF Error Messages
OSPF Error Messages
Open Shortest Path First en-or messages
Error Message %OSPF-4-BADLENGTH Invalid length in OSPF packet from ID
Explanation The system received an OSPF packet with length field of less than normal
header size or inconsistent with the size of the IP packet in which it arrived This indicates
an en-or in the sender of the packet
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %GSPF4-BADLSATYPE LOG WARNING Invalid isa type in LSA from OSPFCOMPLAIN-IVL
Explanation The router received an LSA with invalid LSA Type The cause is either
memory corruption or unexpected behavior on router
Recommended Action From neighbor address locate the problem router and reboot it
To determine what is causing this problem call your technical support representative for
assistance
Error Message %CSPF-4-CONFLICTING_LSAID Found isa type in LSA from
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
176 System Error Messages OSPF Error Messages
Error Message %OSPF-4-ERRRCV Received invalid packet from
Explanation An invalid OSPF packet was received Details are included in the error message The cause might be misconfigured OSPF or an internal error in the sender
Recommended Action Check the OSPF configuration of the receiver and the sender for inconsistency
Error Message %OSPF-3 -INTERI\JALERR Internal error chars OSPF_COMPLAIN_IVL
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %OSPF-3-NOBACKBONE Flagged as being an N3R without backbone
Explanation The router was flagged as an Area Border Router ABR without backbone
area in the router
Recommended Action Restart the OSPF process
Error Message %OSPF3-NOCONNDB No database entry for connected address
Explanation While calculating OSPF routes the router could not find the link-state
advertisement that represents the connected route in the router
Recommended Action Clear the IP routes in the routing table by entering the command
clear ip ro
System Error Messages 177 OSPF Error Messages
Error Message %OSPF-3--NOLSA Failed to find this router LSA in
Explanation The router is not able to find its own router link-state advertisement This can
occur occasionally and self-correct However if this message recurs restart the OSPF
process
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CSPF-3-NOMEMORY No memory for
Explanation The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If
conditions warrant upgrade to larger memory configuration
Error Message %OSPF-4--NONEIGHBOR Received from unknown neighbor
Explanation OSPF hello database description or database request packet was received
but the router could not identify the sender
Recommended Action This situation should correct itself If the message recurs call
your technical support representative for assistance
Error Message %CSPF-4-NORTRID Could not allocate router ID
Explanation OSPF failed while attempting to alocate router ID from the IP address of
one of its interfaces
Recommended Action Make sure that there is at lease one interface that is up and has
valid IP address If there are multiple OSPF processes running on the router each process needs its own unique router ID You must have enough up interfaces so that each of them can obtain router ID
178 System Error Messages OSPF Error Messages
Error Message %OSPF-6-NOSRCPDB ex_route_callbackQ Cant find the src protocol to redistribute net
Explanation OSPF attempted to redistribute route but could not fine valid source protocol
Recommended Action No action is required
Error Message %OSPF6-NOTREDIST1 exroutecallbackfl do not redistribute net
Explanation For information only
Recommended Action No action is required
Error Message %0SPF-6-NOTREDIST3 build_ex_routeQ dont redistribute net advertises it already
Explanation For information only
Recommended Action No action is required
Error Message %OSPF-4-NOTREDIST4 Database scanner external LSA is lost reinstalls
Explanation The software detected an unexpected condition The router will take
corrective action and continue
Recommended Action Record the entire error message and note any OSPF problem you technical experience Report the error message to your support representative
System Error Messages 179 OSPF Error Messages
Error Message %OSPF4NOTREDIST5 db_iree external LSA
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %OSPF-4--OSPFINTIJOWN Interface is up but OSPE state is down Clean up OSPFSOMPLAIN_IVL
Explanation An inconsistency in an internal state was found and corrected
Recommended Action Informational message only No action required
Error Message %OSPF-3-UNXNOWNSTATE Reached unknown state in neighbor state machine
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %OSPF-4-VIRTUAL_ILCNON_BACKBONE Virtual link information found in nonbackbone area OSPF_COMPLAIN_IVL
Explanation An internal error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
180 System Error Messages PA Error Messages
PA Error Messages
Port adapter error messages
Error Message %PA-2BADIDB PA interface 1db incorrect
Explanation The port adapter system control block PASCB data structure indicates
zero interface descriptor block 1DB
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %PA-2-BADINTERFACE msg_badsubunit
Explanation The software specified an out-of-range port adapter interface
it and it Recommended Action Copy the error message exactly as appears report to your
technical support representative
Error Message %PA-2 -BADPABAY msg_badbay
Explanation The software specified an out-of-range port adapter bay
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %PA-2-BADPASCB PA interface pascb incorrect
Explanation The port adapter system control block PASCB data structure was
incorrectly set in the command data structure
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 181 PAD Error Messages
Error Message %PA-2UNDEFPA rnsgundefpa
driver for that in the Explanation The software already has port adapter type specified bay
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %PA-2-UNDEFPABRIDCE msguridefpabridge
Explanation The software does not have driver for that port adapter protocol control
information bridge in the specified bay
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
PAD Error Messages
X25 packet assembler/disassembler error messages
Error Message %PAD-3--GETLINE Tty bad return code jdec frornx3_getlne
%PAD-2INTR called at interrupt level
%PAD-2--PUTSETUP Tty buffer already setup
Explanation An internal software error occurred
the Recommended Action If any of these messages recur copy error message exactly as
it appears and report it to your technical support representative
182 System Error Messages PARSER Error Messages
PARSER Error Messages
Parser error messages
Error Message %PARSER4-BADCFG Unexpected end of configuration file
Explanation This message occurs when configuration is read from the Trivial File Transfer Protocol TFTP server or nonvolatile RAM NVRAM and the end of the file is encountered before the end statement The configuration may be corrupted or incomplete
What was read is in effect
Recommended Action Make sure the configuration is good then execute either copy
running-config startup-config command to write the good configuration to NYRAM or
copy running-config tftp command to write to network TFTP server
Error Message %PARSER4BADRANGE Bad range for command
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 183 PARSER Error Messages
Error Message %PARSER3--BADSUBCMD Unrecognized subcommand in Function Command Switch value
%PARSER-3-CREATEINT Cant create any more subinterfaces
%PARSER-4-INVLaLJNE Invalid line in NV generation
%PARSER-4-LINKPOINT Parser reached link_point
%PARSER4-MULFUNCS Unknown test in test_multiple_funcs
%PARSER-4-MULTIPLElFS interface_actiom multiple ifs present when unit_only set
%PARSER-3-NOLINK no link_point in the command chain
%PARSER-4-NUMEELP general_number_short_help Invalid number flag
%PARSER-4-NVGEN nvgen_token called but csb-nvgen not set
%PARSER-4-PROTOADDR protoaddr_action Unknown link_type
Explanation The parser failed an internal software check
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %PARSER2-INTDISABLE Interrupts disabled in mode by command
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
184 System Error Messages PARSER Error Messages
Error Message %PARSER-4-INVLDNVGEN Invalid function called in NVG of
Explanation An error occurred
Recommended Action Copy the error message exactly as it appears Execute show version command and copy the displayed information Contact your technical support representative
Error Message %PARSER3-NOMEMORY no memory for
Explanation memory allocation failed possibly because the router is out of memory
because the is than it should or parser using more memory
Recommended Action If the router is running out of memory reduce other system
sufficient but is activity to ease memory demands If the router has memory the parser low for assistance on memory call your technical support representative
System Error Messages 185 PCBUS Error Messages
PCBUS Error Messages
PCbus PC ISA-to-AccessPro router interface error messages
Error Message %PCBUS3-BADENCAP msgtxt_badencap
Explanation nonHDLC encapsulation packet was received The packet will be treated as an HDLC packet and subsequently be dumped
Recommended Action An informational message only No action required
Error Message %PCBUS- NOMEMORY msgtxt_nomemory
Explanation This message is logged via the global logging command when an attempt
to get packet memory or data memory fails The router will crash right after the error is logged
Recommended Action An informational message only No action required
PHM Error Messages
Protocol-independent multicast error messages
Error Message %PIM1-INVALID_RP_JOIN Received Join from or invalid RP
Explanation downstream PIM router sent join message for the shared tree which this
router does not want to accept This behavior indicates that this router will let only
downstream routers join to specific rendezvous point
Recommended Action Configure all downstream leaf routers to join to the RP that is
allowed by upstream routers toward the validated rendezvous point
186 System Error Messages PPP Error Messages
Error Message %PIM-1-INVALID_RP_REG Received Register from for not willing to be PP
Explanation PIM router received register message from another PIM router that
identifies itself as the rendezvous point If the router is not configured for another
rendezvous point it will not accept the register message
Recommended Action Configure all leaf routers first-hop routers to multicast sources
with the IP address of the valid rendezvous point
PPP Error Messages
Point-to-Point Protocol error messages
Error Message %PPP4-CONnJAK fsm_rconfnak possible CONENAK loop
Explanation The remote and local PPP cannot agree on set of options that both can perform
Recommended Action If this message recurs copy the error message exactly as it
appears and report it to your technical support representative
Error Message %PPP4-IPXNET mismatched IPX network numbers Ours theirs
Explanation The two ends of serial link have different IPX network numbers
Recommended Action Confirm the configuration of both devices
System Error Messages 187 QA Error Message
Error Message %PPP-6--LOOPED The line appears to be looped back
Explanation The communications line appears to be echoing the characters that are sent toiL
communications Recommended Action Check your data equipment to make sure it is
configured correctly
Error Message %PPP-4--NOEXTTACACS PPP TACACS is configured but extended TACACS is not
Explanation PPP was configured to use the Terminal Access Controller Access Control
System TACACS but extended TACACS was not configured or was disabled
Recommended Action Either issue the no ppp use-tacacs command to stop PPP from
using TACACS or issue the tacacs-server extended command to enable extended TACACS
QA Error Message
Queue and accumulator error message
Error Message %QA3 -AIJLCC
Explanation This is software error
Recommended Action Copy the error message exactly as it appears Also copy the
output of show version and show cont cbus Contact your technical support representative
188 System Error Messages QLLC Error Messages
QLLC Error Messages
Qualified Logical Link Control error messages
Error Message %QLLC3--BADOPCODE Opcode is invalid
Explanation Either remote source-route bridging or local acknowledgment is configured
incorrectly
Recommended Action Verify that remote source-route bridging and local
acknowledgment are configured correctly
Error Message %QLLC-3-BADQLLCSTATE Bad QLLC state
Explanation An invalid QLLC primitive was detected
Recommended Action Verify that the partner QLLC device is configured correctly
Error Message %QLLC-3-BADRSRBOPCODE Bad opcode from to
Explanation Either remote source-route bridging is incorrectly configured or the other
RSRB device is down
Recommended Action Verify that remote source-route bridging is configured correctly
with the right version of the lOS software
Error Message %QLLC-3-BADSTATE Bad QLLC state
Explanation An invalid LLC primitive was detected
Recommended Action Verify that the Token Ring ports and any participating LAN
devices are configured correctly
System Error Messages 189 QLLC Error Messages
Error Message %QLLC-3-BADSTATEEVENT Bad QLLC state event macaddr
Explanation The LLC primitive specified placed the router in an invalid state
Recommended Action Verify that the Token Ring ports and any participating LAN
devices are configured correctly
Error Message %QLLC-3-BAQSUBADDRESS is not subaddress of
Explanation remote X.25 device is calling the router for QLLC service using an X.121 121 address that is not proper subaddress of the routers address
Recommended Action Enable subaddressing on the router and make sure that the
remote X.25 device uses the correct subaddress for the QLLC service it will use
Error Message %QLLC-3-DIFFPRTR Different partner originally now
Explanation The partner for this QLLC virtual MAC address does not match the MAC
address that was defined with the qllc partner command
Recommended Action Verify that the qllc partner statement in the configuration file is
correct
Error Message %QLLC- -GENERRMSC
Explanation The text string provided with this error message describes the specific QLLC problem
Recommended Action Follow the instructions that appear with the error message Copy
the error message exactly as it appears and report it to your technical support
representative
190 System Error Messages QLLC Error Messages
Error Message %QLLC3-IFRAJy
Explanation An I-Frame was discarded due to network congestion
Recommended Action Verify that the LAN is not beaconing and that it is not in congested state Copy the error message exactly as it appears and report it to your technical support representative
Error Message %QLLC3-INCALL_CFG Incoming call No QLLC Service Access Point Configured for x.25 subaddress
Explanation remote X25 device is calling the router for QLLC service using subaddress that was not configured by the X.25 routing facility The subaddress was not configured for QLLC service
Recommended Action Correct the QLLC configuration Configure only the subaddress on the QLLC service not the complete X.l2l address that the remote X.25 device uses
Error Message %QLLC-3-LNXNOTFQUND inx_remove_macaddr_hash did not find target mx
defined this Explanation The qile srb command was not for interface
Recommended Action Add valid qite sit statement for this serial interface
Error Message %QLLC-3-NOLLC2 Unable to open an 11c2 session
Explanation An LLCZ session could not be established with the destination MAC address
is Recommended Action Verify that the qile partner statement in the configuration file correct and that the partner is on the desired LAN
System Error Messages 191 QLLC Error Messages
Error Message %QLLC-3-NOMACADDR No inc entry for macaddr
Explanation No virtual MAC address was defined for this interface
Recommended Action Define the virtual MAC address using either the x25 map qllc or
the xZS PVC qile command
Error Message %QLLC-3--NOMEM Not enough memory available
Explanation There is not enough memory in the system to complete this request
Recommended Action Add more memory to the router Otherwise reduce the
configuration or the load on the routet
Error Message %QLLC-3-NONULLXID Couldnt make null xid
Explanation An attempt to create an IEEE XID failed
Recommended Action Verify that the qile partner statement in the configuration file is
correct and that the partner is on the desired LAN
Error Message %QLLC-3-NOPAKENQ Pak enqueue failed
Explanation packet was not sent to the LAN
Recommended Action Verify that the LAN partner is configured correctly and that the
partner is on the desired LAN
Error Message %QLLC-4--N0QLLC Unable to open qllc session current statue is
Explanation QLLC session could not be established
Recommended Action Verify that the qIIc partner and the qllc xid commands are correct
192 System Error Messages QLLC Error Messages
Error Message %QLLC-3-NOQLLCBUFFER bit Reassembly failed couldnt allocate packet
Explanation The router ran out of memory to allocate buffers
Recommended Action Make sure that the router configuration is adequate for the service expected of it You might want to tune the buffer pools or upgrade to larger router At the very least you will need more memory
Error Message %QLLC-3-NOQSR No QLLC Service Access Points defined 10 ONESEC
Explanation No QLLC services have been configured even though the router will accept incoming calls for QLLC
Recommended Action Configure the QLLC service required
Error Message %QLLC-3-NO RESOURCE Incoming Call Insufficient resources available 10 ONESEC
Explanation This message is reporting insufficient system memory
Recommended Action Upgrade the memory
Error Message %QLLC-3-NOXID2 Couldnt make xid
Explanation The QLLC XID could not be forwarded to the LAN
Recommended Action Verify that the qile partner and the qJlc xid commands are correct
System Error Messages 193 QUICC Error Messages
Error Message %QLLC3-NULLPTR ptr is null
Explanation The specified structure was not configured
Recommended Action Confirm the configuration commands for the structure
Error Message %QLLC-3--QLLCMAP ERR Incoming call QLLC map entry not found 10 ONESEC
Explanation software error in the router code occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
QUICC Error Messages
MC68360 Quad Integrated Communications Controller error messages
Error Message %QUICC-3-BADUNIT msgtxt.badunit
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %QUICC5--COLL Unit excessive collisions Retry limit exceeded
Explanation An Ethernet cable is broken or unterminated
Recommended Action Check cables for proper connections termination and so on
194 System Error Messages QUICC Error Messages
Error Message %QUICC_ETHER-5COLL Unit excessive collisions Retry limit exceeded
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %QUICC_ETHER5--HBEAT Unit heartbeat check failure
Explanation software or hardware error occurred
it and it Recommended Action Copy the error message exactly as appears report to your
technical support representative
Error Message %QUICc_ETHER-1--INITFAIL msgtxtjnitfail
Explanation software or hardware error occurred
it and it Recommended Action Copy the error message exactly as appears report to your
technical support representative
Error Message %QUICC_ETUER-5--LATECOLL Unit late collision error
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 195 QUICC Error Messages
Error Message %QUICCETHER1-LOSTCARR Unit lost carrier Transceiver problem
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %QUICC_ETHER-3-UNUERFLO Unit underf low error
Explanation While transmitting frame the Ethernet controller chips local buffer
received insufficient data because data could not be transferred to the chip fast enough to
keep pace with its outputrate Normally such problem is temporary depending on
transient peak loads within the system
Recommended Action The system should recover No action is required
that be related data traffic If the problem recurs it indicates hardware error might to
patterns Copy the error message exactly as it appears and report it to your technical
support representative
Error Message %QUICC5-HBEAT Unit heartbeat check failure
Explanation The Ethernet transceiver is malfunctioning
Recommended Action Replace the hardware
Error Message %QUICC-5-djATECOLL Unit late collision error
Explanation The Ethernet cable might be too long or there could be too many repeaters
such that the delay from one end to the other is too long The Ethernet cable might be overloaded with too many users
Recommended Action Verify that your Ethernet cable is the correct length and that you
do have in If these are not the hosts from not too many repeaters use problem try removing
the Ethernet segment to reduce the load
196 System Error Messages OUICC Error Messages
Error Message %QUICC5LOSTCARR Unit dec lost carrier Transceiver problem
Explanation The Ethernet lOBaseT cable is unplugged
Recommended Action Connect the lOBaseT Ethernet cable
Error Message %QUICC-l--NOMEMCRY msgtxt_nomemory
Explanation The MC68360/QUICC CPU was unable to access the memory it needs to carry out its functions Here are some possible causes
The network is large requiring lot of memory for routing tables and so on
The router configuration has many features enabled each of which require certain amount of memory
software error memory leak exists
Recommended Action Reduce system activity to ease the memory demand or upgrade to larger memory configuration
Error Message %QUICC-3 -OWNERR msgtxt_ownerror
Explanation An internal software error occurred
Recommended Action Call your technical support representative to obtain software upgrade
Error Message %QUICC_SERIAL-3--CTSLOST Unit Clear Send Lost
Explanation The Clear To Send CTS input signal on data terminal equipment DTE serial interface became inactive while transmitting frame This problem stems from communication line failure or cable disconnection
Recommended Action Check the serial interface cable and or communication equipment such as the channel service unit/data service unit CSUIDSU
System Error Messages 197 QUICC Error Messages
Error Message %QUICC_SERIAL-1-INITFAIL rnsgtxt_init fail
Explanation The serial interface controller of the QUICC chip could not be initialized or
started for operation There is probably hardware problem
Recommended Action Power cycle the system If the error recurs replace the unit
Error Message %QUICC_$ERIAL-5-LINEFLAP Unit excessive modem control changes
ExplanatVon The system received too many modem control signal interrupts Modem control signals are hardware handshake signals between data terminal equipment DTE and data communications equipment DCE The signals include either data carrier detect DCD or data set ready DSR or both DCD and DSR
Recommended Action Check the serial interface cable The error can occur if the cable
is disconnected or has come loose and is picking up noise If the cable appears to be
connected correctly check the equipment connected to the cable
Error Message %QUJCCSERIAL-3JJNDERFLO Unit dec
Explanation While transmitting frame the serial controller chips local buffer received
insufficient data because data could not be transferred to the chip fast enough to keep pace
with its output rate Nonnally such problem is temporary depending on transient peak loads within the system
Recommended Action The system should recover No action is required
If the be data problem recurs it indicates hardware error that might related to traffic
patterns Copy the error message exactly as it appears and report it to your technical
support representative
198 System Error Messages RADIX Error Messages
Error Message %QUICC-3-UNDERFLO Unit underf low error
Explanation The Ethernet hardware is requesting data faster than the system can supply
it This should never happen unless serious malfunction has occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
RADIX Error Messages
RADIX Error Messages
Error Message %RADIX-3-ADDMASK Error adding mask entry ONESEC
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message
%R DIX3-EADTREE Invalid pointer to head off tree ONESEC
Explanation software programming error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %RADIX-3-DELETE Error deleting trie entry CNESEC
Explanation software programming error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Syslem Error Messages 199 RADIX Error Messages
Error Message %RADIX-2-INIT No memory for radix initialization
Explanation The system ran out of memory during initialization.This should only occur
if an image is too large for the existing dynamic memory
Recommended Action Use smaller subset image or upgrade hardware
Error Message %R DIX-2-NOMAXKEYLEN Programmer error maximum radix key length not set
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %RADIX-3-NOMEMORY No memory available
Explanation The system is out of memory
Recommended Action Try one of these actions to correct the problem
Reduce the number of routes accepted by this router
Upgrade hardware
Use smaller subset image on run-from-RAM platforms
Error Message %PADIX-4-ORPHAN Orphaned mask refcount at next 5ONESEC
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
200 System Error Messages RCMD Error Messages
RCMD Error Messages
Remote command error messages
Error Message %RCMD-4INVAl1IDHOST Invalid host address
Explanation The TP address of the incoming connection was not valid
Recommended Action Add an entry to the rhost database or determine which client IP
address is valid by examining the rhost database
Error Message %RCMtD4-NOMFMORY No memory available for Rcmd
Explanation There was not enough memory for RCP or RSH to allocate memory
Recommended Action Wait for memory to become available or add more memory
Error Message %RCMD4-NORSHPROC Rsh Process Fork failed
Explanation Creation of the rsh daemon failed This is usually caused by lack of
resources such as memory or vty
Recommended Action Wait for resources to become available
Error Message %RCNIJ-4-RCMDDNSFAIL DNS hostriame/ip address mismatch
Explanation The IF address for an incoming rcmd request is not registered with DNS
Recommended Action Add the IF address to DNS
System Error Messages 201 REGEXP Error Message
Error Message %RCMD-4-RCPATTRMPTEIJ Remote copy denied
Explanation An attempt was made to connect to router through RCP but the router was
not configured as an RCP server
Recommended Action Configure an RCP server
Error Message %RCMD-4-RSHATTEMPTED Remote shell denied
Explanation An attempt was made to connect to router through rsh but the router was
not configured as an rsh server
Recommended Action Configure an rsh server
Error Message %RCMD4--RSHPORTATTEMPT Attempted to connect to RSHELL port
Explanation An attempt was made to connect to router through the rsheil port 514 but
the router was not configured as an RSH or RCP servet
Recommended Action Configure an RSFT or RCP server
REGEXP Error Message
Regular expression parser error messages
Error Message %REGEXP2-BADLIST Regular expression access check with bad list
Explanation An internal software error occurred
Recommended Action If this message recurs call your technical support representative
for assistance
202 System Error Messages RIP Error Message
RiP Error Message
Routing Information Protocol error message
Error Message %RIP-3--NOSOCKET Unable to open socket
Explanation The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If
conditions warrant upgrade to larger memory configuration
RSP Error Messages
Route Switch Processor error messages
Error Message %RSP-3-AIPPANIC Panic
Explanation This message occurs when an ATM Interface Processor AlP crashes and
send and it crashed can out message indicating where why
Recommended Action Record the information and call your technical support
representative for assistance Reload the microcode into the AlP
Error Message %RSP-3-BADHWREV slot has wrong hardware revision
Explanation The hardware in the indicated slot needs to upgraded for operation with the RSP
Recommended Action Upgrade the board
System Error Messages 203 ASP Error Messages
Error Message %RSP-4-COOKIE Corrupt or missing MAC address ccokie\n using random base
Explanation This message indicates the part containing the MAC addresses allocated to this chassis could not be accessed or was found to be corrupt either due to hardware
problem or manufacturing problem
Recommended Action Report this error to your technical support representative
Error Message %RSP-3 -ERROR
Explanation This message can take many forms It provides information about software error
Aecom mended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %RSP-3-FLASH error
Explanation The Flash memory Management Information Base MIB software detected
an errot
Recommended Action Copy the error message exactly as it appears along with the
output from show version command and the circumstances under which the error message
was sent Report this information to your technical support representative
Error Message %RSP3--FOREVER cmd to took usecs done
Explanation command from the RSP to an IP took longer than expected
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
204 System Error Messages RSP Error Messages
Error Message %RSP3-IDPROM Bad or missing ID EEPROM controller type
Explanation The ID BEPROM on the RSP is missing or bad
Recommended Action This message indicates manufacturing error Report this error to your technical support representative
Error Message %RSP3-INVRTN Invalid return queue bufhdr
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %RSP-3-INvRTNBCASTID Invalid return queue bcast_id \n bufhdr
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %RSP--3-IPC
occurred The details about Explanation An Interprocess Communication IPC error what was attempted and what went wrong will be printed
Recommended Action Copy the error message exactly as it appears Copy down the Contact technical routers configuration along with any other relevant information your support representative for assistance
System Error Messages 205 RSP Error Messages
Error Message %RSP-3--LOVEGIANT Card wants byte love letters but only got bytes
Explanation An inconsistency between the microcode and the system code was detected
Recommended Action Report this error to your technical support representative
Error Message %RSP-3--LOVENOTE corrupt lovenote
Explanation This message indicates miscommunication between the RSP and an IP
Recommended Action Report this error to your technical support representative
Error Message %RSP-3--MSDOG Master/slave watchdog timed out
Explanation The system software failed to reset the master/slave watchdog timer causing
it to time out This behavior could indicate software problem or hardware problem
Recommended Action Copy the error message exactly as it appears Copy down the
routers configuration along with any other relevant information Contact your technical
support representative for assistance
206 System Error Messages RSP Error Messages
Error Message %RSP-3--NSFIX Fixing by setting to default
Explanation The characters shown can be either on the slave RSP setting or on the master
RSP setting
The ROM monitor default slave RSP setting is not synchronized with the system
configuration file specifications During bootup the system image detects the mismatch and
modifies the ROM monitor setting to conform with these specifications
This mismatch most likely occurred because new RSP was being installed and booted in
environment for the first high system availability HSA dual RSPs time Alternatively
in established HSA configurations this message may result from previous Interproeess
Communication IPC error occurring while the HSA environment is reconfigured
Recommended Action
Using the show version or show boot command determine which slot contains the
current slave RSP
Using the show config command determine which slot has been specified as the default
slave RSP If there is no slave default-slot command in the configuration file the
value defaults to the highest numbered CPU slot slot on Cisco 7507 and slot on Cisco 7513
If the slot number obtained in Step is the same as the number obtained in Step then no
further action is required You have configured HSA in simple hardware backup mode and
both RSPs are identical
in However if the two slot numbers diffei you have configured HSA software error
protection mode and will have different images running depending on which RSP is
currently the slave RSP If the slot numbers discovered in Steps and differ reload your
router to ensure that the desired system image is running After the reload the actual slave
RSP will match the default slave RSP specified in or inferred from the system
configuration file
the For details of various HSA configuration modes consult Cisco lOS Configuration
Fundamentals Configuration Guide See the Loading System Images and Configuration
Files chapter Cisco 7500 series only
System Error Messages 207 ASP Error Messages
Error Message
%RSP-3-MSVERS Master has rn/s version slave has rn/s version
Explanation The master and slave are running incompatible software versions with
regards to the master/slave exchange process
Recommended Action If the slave image global configuration is used to override the
default slave image from the bundle then the slave image is incompatible Update either
the master or slave image to ensure the two are compatible
If the slave is running the image from the bundle execute and record the output of show
version show running-config and show controller cbus commands Report this
information and the error message to your technical support representative
Error Message %RSP-3--NOLOVE Corrupt lovenote
between RSP Explanation This message indicates miscommunication the and an TP
Recommended Action Report this error to your technical support representative
Error Message %RSP-3--NOMAC Cant allocate MAC address for interface
Explanation No MAC address was available for allocation to the specified interface
Recommended Action Report this error to your technical support representative
208 System Error Messages RSP Error Messages
Error Message %RSP-2-NO4ORY No memory available for
Explanation An attempt at memory allocation failed
Recommended Action Try these actions to remedy the problem
Add memory
Disable some features
Apply filtering to decrease the size of system data structuresthe routing table for example
In general reduce other system activities to ease memory demands If conditions warrant upgrade to larger memory configuration
Error Message %RSP3NORESTART unable to schedule restart for output queue
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %RSP-3-NOSTART No microcode for card slot
Explanation No microcode is defined or available for the specified card
Recommended Action Reconfigure the card to specify an existing microcode file
Error Message %RSP2-QAERRQR error at addr loq data
Explanation software error was detected during packet switching
Recommended Action Call your technical support representative for support
System Error Messages 209 RSP Error Messages
Error Message %RSP-3 -RESTART
Explanation The cBus buffer memory was reset and reallocated
Recommended Action Report this error to your technical support representative if
memory is not reset manually by changing the MTU on an interface for example
Error Message %RSP-3--RESTARTREQ
Explanation Some part of the software requested that eBus buffer memory be reset and reallocated
Recommended Action Report this error to your technical support representative if
memory is not reset manually by changing the MTU on an interface for example
Error Message %RSP-3-SLAVECI-IANGE Sfave changed state from to
Explanation
The slave RSP has undergone hardware state change The old state and new state are shown
Possible states are
nonparticipant
slave
master
unplugged
Possible state changes indicated by the above message are
any to unplugged
unplugged to nonparticipant or slave
nonparticipant to slave
slave to nonparticipant
Any other combination is unexpected
210 System Error Messages RSP Error Messages
Recommended Action
Causes and recommended solutions
The slave RSP has been removed Consider reinstalling it if continued high system
availability HSA operation is required If the slave RSP is present ensure that it is
properly seated in the card cage
slave RSP has been installed Configure the router for HSA See the Loading System
Images and Configuration Files chapter in theConfiguration Fundamentals
Gonjiguration Guide Cisco 7500 series only for more details In particular use the
slave sync config command to ensure that the new slave RSP is configured consistently with the current master RSP
CAUTION Failure to ensure consistent configuration on freshly installed slave RSP
might result in undefined behavior if the router reloads
previously crashed slave RSP has been reset or newly installed slave RSP is in
transition from unplugged to nonparticipant and finally to slave state No action is
required
The slave RSP image has crashed Log in to the slave RSP console using the if-console
slot command You will now be connected to the ROM monitor prompt on the slave
RSP Diagnose the slave RSP failure For example capture the output from the stack
and context RUM monitor commands Provide that information to your technical
support representative along with the routers configuration and any other relevant
information so that the problem can be investigated
Log out from the slave RSP console port using Ctrl-c or Ctrl-z and enter the slave
reload global configuration command on the master RSP to bring the slave RSP back ohline
All other state changes indicate software or hardware error Provide the routers
configuration and any other relevant information to customer support so that the
problem can be investigated
System Error Messages 211 RSP Error Messages
Error Message %RSP3-SLAVENASTER Slave stole mastership
Explanation The master RSP detected that the slave RSP had taken mastership of the slave router The old master RSP will reload and become the RSP letting the new master
RSP take over This behavior indicates software or hardware error
Recommended Action Copy the error message exactly as it appears Copy down the
routers configuration along with any other relevant information Contact your technical
support representative for assistance
Error Message %RSP-3-SLAVEROM
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %RSP-5-SLAVEUP Slave changed to state Running
Explanation This is an informational message to indicate that the slave RSP has started
running the slave RSP image This message after the router boots or after the slave reload
global configuration command is issued on the master RSP
Recommended Action No action required
Error Message %RSP-2-STALL partially inserted or removed IPs on cyBus
Explanation Most likely board is not fully seated in the chassis less likely possibility
is hardware problem with the RSP or backplane
Recommended Action Try reseating the boards Call your technical support
representative for assistance if this message persists
212 System Error Messages RSRB Error Messages
Error Message %RSP-3-XBUFHDR corrupt bufhdr
Explanation Miscommunication occurred between the RSP and an IF
Recommended Action Report this error to your technical support representative
RSRB Error Messages
Remote source-route bridging error messages
Error Message %RSRB-4--BADLEN Peer bad length tm
%RSR8-4--BADLEMIP Peer bad length
Explanation An internal software error occurred
Recommended Action If either message recurs call your technical support
representative for assistance
Error Message RSPE3-BAD\TERSIONF3T FST in version mismatch mine theirs
%RSRB3-BADvERSIONIF IF in version mismatch mine theirs
Explanation The remote end of direct serial peer is running the wrong version of the system software Either the local end the remote end or both are not up to date
for Recommended Action Call your technical support representative an update
System Error Messages 213 RSRB Error Messages
Error Message %RSRB-3-BAD\TERSIQNTCp version mismatch mine theirs
Explanation The remote end of TCP remote peer is running the wrong version of the
system software Either the local end the remote end or both are not up to date
Recommended Action Call your technical support representative for an update
Error Message %RSR3-4BADVRE Bad vre type
%RSRB4-CONIPST Peer CONN illegal state
%RSRB-4-CONNILLSTATE Peer CONN illegal state
%RSRB-4--C0NNSTAT Peer dec/ IFin bad connection state
Explanation An internal software error occurred
Recommended Action If any of these messages recur call your technical support
representative for assistance
Error Message %RSRB-3-FSTEPR op len tm
Explanation The remote end of direct serial RSRB connection detected configuration
problem or traffic that is not recognized by the configuration
Recommended Action Examine the configuration on both sides of the serial connection
for possible problems Examine the traffic being offered for propagation with respect to the
configuration The destination target ring is denoted by the value of tm
214 System Error Messages RSRB Error Messages
Error Message %RSRB-3--HDRNOVRP Peer HDR no vrp
%RSPB4---HIJRRECV Peer HDR recv state invalid not empty
%RSRB3-HDRVRP Peer HDR vrp state wrong
Explanation An internal software error occurred
Recommended Action If any of these messages recui call your technical support representative for assistance
Error Message %RSRB-3--JFERR op len tm
Explanation The remote end of direct serial RSRB connection detected configuration problem or traffic that is not recognized by the configuration
Recommended Action Examine the configuration on both sides of the serial connection for possible problems Examine the traffic being offered for propagation with respect to the configuration The destination target ring is denoted by the value of tm
Error Message %RSRB-4-ILLPEER Peer illegal state
%RSRB4-LOCAL Unit local/vring set simultaneously vrn
Explanation An internal software error occurred
Recommended Action If either of these messages recur call your technical support representative for assistance
System Error Messages 215 RSRB Error Messages
Error Message %RSRB-3-NOMEMORY Unit no memory or
Explanation The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If
conditions warrant upgrade to larger memory configuration
Error Message %RSR3-NOTREM Null 1db and not remote
%RSRB4--OPTNTJLL Remopened and NULL
%RSRW-4--PEERSTAT Peer wrong state
Explanation An internal software error occurred
Recommended Action If any of these messages recut call your technical support
representative for assistance
Error Message %RSRB-4RNGXFAIL Ring exchange failure resetting peer
Explanation The RSRB peer initiation logic failed due to memory shortage or congestion condition
Recommended Action The problem should clear and the peers should re-open without
operator intervention
Error Message %RSRB3--SENDPUNTFST sent to
%RSRH3SENDPUNTIF sent to
Explanation The local end of direct serial RSRB connection detected configuration
problem or traffic that is not recognized by the configuration
Recommended Action Examine the configuration on both sides of the serial connection
for possible problems Examine the traffic being offered for propagation with respect to the
configuration
216 System Error Messages S4T68360 Error Messages
S4T68360 Error Messages
S4T68360 error messages relate to the 4-port synchronous serial adapter based on the
68360 processor
Error Message %S4T68360--1-DISCOVER only found interfaces on bay shutting down bay
Explanation port adaptor hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %S4T68360-l-DWNLDFL s4tmsg_downloaJail
Explanation The S4T hardware has failed It could not download its operational microcode
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %S4T68360-1-DWNLDCKSM s4tjnsg_cksmjail
Explanation The download of the internal firmware to the S4T failed to checksum
correctly This usually indicates hardware failure of the S4T or the Versatile Interface Processor VIP
Recommended Action Perform power cycle If the problem persists the S4T hardware may have problem
System Error Messages 217 S4T68360 Error Messages
Error Message %S4T683601-INITFAIL s4t_ms Jnitf all
Explanation The S4T port adaptor failed to complete hardware initialization
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %S4T6836O3NBXREAD s4t_msg_nibxrcad
Explanation The S4T has not responded to message from the Versatile Interface
Processor VIP within specified time
Recommended Action Perform microcode reload of the VIP If the problem persists it
indicates that the S4T or VIP hardware failed
Error Message %S4T683 60-l-NOTCMPLT s4L_msgdownload_ncmplL
Explanation The S4T port adaptor hardware failed It did not acknowledge the
completion of the operational microcode download
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %34T68360-l-NOTREADY s4tjnsg_notready
Explanation The S4T port adaptor hardware failed The S4T port adaptor would not begin
to download the operational microcode
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
218 System Error Messages S4T68360 Error Messages
Error Message %S4T683603-N0TS4T68360 At device reported
Explanation The S4T hardware failed non-S4T device pointed at the software for the S4T
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %S4T683 60-3 -OQNERR rnsgtxt_ownerror
Explanation software or hardware error occurred The S4T driver detected that the transmit ring is an inconsistent and unrecoverable state
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %S4T68360-3-PANIC s4Ljnsg_panic
Explanation The S4T firmware detected an illegal or unexpected CPU exception or condition This may be caused by software error or by hardware failure
Recommended Action Perform microcode reload of the Versatile Interface Processor
it the S4T hardware failed VIP If the problem persists indicates that
Error Message %S4T68360-1--STARTFAIL s4t_msgstartfail
Explanation software or hardware error occurred The S4T interface is not responding to commands used to initialize it
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 219 S4T68360 Error Messages
Error Message %S4T68360-1-.STOPFAIL s4tjnsg_stopfail
Explanation The S4T port adaptor failed to respond to request to disable an interface
Recommended Action Copy the error niessage exactly as it appears and report it to youi
technical support representative
Error Message %S1T6836O3-TOOSM7LL s4L_msgtoosmall
Explanation An output packet was detected that was smaller than the minimum allowable
datagram size An error in another driver or an error in the system software probably
triggered this error message
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
220 System Error Messages SCHED Error Messages
SCHED Error Messages
Scheduler error messages
Error Message %SCHEIJ-2-ATTRCMD Attempt to attribute on process 30 ONESEC
%SCHED2-ATTRVALUE Attempt to set bad value on process
%SCHED-2-EDISMSCRIT Critical priority process may not dismiss
%SCFJED-3-LOSTWAKEUP Wakeup information for process lost maj mm 30ONESEC
%SCHED-2-NOATTR Attempt to unknown process attribute 30 ONESEC
%SCRED-2-NOTWATCHTIMER timer not being watched 30ONESEC
%SCHED-3--PAGEZERO Low memory modified by
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technica support representative
System Error Messages 221 SCHED Error Messages
Error Message %SCHED3-PRIORITY Illegal priority specified for process 33ONESEC
%SCHED-2-QUEUENOTEMPTY Attempt to delete non-empty watched queue address 3QQSEC
%SCHED-2-SEMUNLOCK attempted to unlock semaphore owned by 3QQSEC
%SCHED-3-STACKSIZE Illegal stack size specified for process 30ONESEC
%SCHED-3-STUcKMTMR Sleep w/ expired mgd timer time %Ta %TE ago ONEMIN
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SCHED-3-STILLWATCHING Process still watching
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SCHED-3-STILLWATCHINGT Process still watching timer
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
222 System Error Messages SCHED Error Messages
Error Message %SCHED3-STUCKThER Sleep w/expired timer time %Ta %TE ago ONEMIN
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SCHEtJ-3-THRASHING Process thrashing on watched ONEMIN
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SCHED-3--UNEXPECTEDEVENT Process received unknown event maj mm 30ONESEC
%SCHED-3-tJNEXPECTEDMESSAUE Unknown message re eived ptr arg nun arg 30ONESEC
%SCHED-3-UNEXPECTEDQUEUJf Queue event for unknown queue index 30ONESEC
%SCHED-3-UNEXPECTEDTIMER Unknown timer expiration timer type
10 ONESEC
%SOHEtr-2--WATCH Attempt to uninitialized watched address 30ONESEC
%SCHED-2-WATCHTIMER Request to watch timer timer active 30ONESEC
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 223 SDLC Error Messages
SDLC Error Messages
Synchronous Data Link Control error messages
Error Message %SDLC-6-BADFRAJyIE Received bad SDLC frame address control 30ONESEC
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SIDLC5-C0NFIGERR addr Sent SNIRM received SNRM Check link station roles 20ONESEC
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SDLC-4--CTRLBAD Interface Invalid control field
Explanation bad SDLC frame was received
Recommended Action If this message recurs check the SDLC serial line and the devices
attached to it
Error Message
%SDLC-3-DLTJ ERROR DLIJ failed to close station before reopening ONESEC
Explanation hardware or software error occurred
Recommended it it Action Copy the error message exactly as appears and report to your
technical support representative
224 System Error Messages SDLC Error Messages
Error Message %SDLC4--DROPPED Dropped SDL1C packet from SDLC hold queue 10
Explanation An SDLC frame had to be dropped from the output hold queue usually because of excessive congestion on the output link
Recommended Action If this message occurs frequently determine why your SDLC link is being overloaded with data and resolve the cause typically by either increasing bandwidth to your SDLC line or reducing the load on your link
Error Message %SDLC-4-FRANEERR Interface Frame error CF VS VR Reason
Explanation FRMR frame was received This can be due to noisy serial line an overloaded SDLC device or corrupted data
Recommended Action If this message recurs service the serial line and the devices attached to it
Error Message %SDLC-2-ILLEGSTATE Illegal state
Explanation An internal SDLC state violation was detected
Recommended Action Record the entire error message and call your technical support representative for assistance
Error Message %SDLC4-INFOBAD Interface Info field not permitted
%SDLC-4-INVNR Interface Invalid NR value
Explanation bad SDLC frame was received
serial line and the Recommended Action If any of these messages recur check the SDLC
devices attached to it
System Error Messages 225 SDLC Error Messages
Error Message %SDLC-5-INVLDGRPCFG Interface ignoring grouppoll mismatch UPOLL 60ONEMIN
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SDLC4-INVLLCRPPOLL Interface Invalid group-poll frame 10
Explanation An unnumbered poll UP was received with the wrong group poll address
Recommended Action Make sure the group poli address configured on the router matches the one configured in the physical unit PU macro GP3174XX in the Network
Control file Program NCP generate
Error Message %SDLC-5-INVLDGRFPOLL Interface not configured for group-poll frame received 50ONEMIN
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SDLC-4-N1TOOBIG Interface Nl too large
Explanation An information frame was received from the other end of the SDLC link that
was larger than allowed with the Nl parameter on this link
Recommended Action Either increase the value of the NI parameter for this interface on
the router or reduce the size of the maximum information frame sent by the other end of the link
226 System Error Messages SDLC Error Messages
Error Message %SDLC2--NOBUF Interface no buffer available to
Explanation Insufficient memory available
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %SDLC-4-NoFPmSPAcE Cannot allocate FRMR frame
Explanation The router needed to generate an FRMR frame but could not allocate the necessary memory for the frame
Recommended Action The fact that memory is so low that it cannot allocate the frame is the Fix the of low far more serious than the reason for generating FRMR cause memory and if the problem still occurs determine why the FRMR must be sent
Error Message %SDLC3--NCINPIDB Input icib not set
Explanation This is software error frame was given to the SDLC handler to process but the interface on which the frame arrived is not known
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SDLC-2-NOPCINTER AW_SDL_SEC with no sdllcllc pointer
Explanation An error condition occurred during SDLLC initiation
Recommended Action No action is required The SDLLC session will restart without operator intervention
System Error Messages 227 SDLC Error Messages
Error Message %SDLC-4--NCUA Interface address non PA frame is received in response to SNRM 99999
Explanation The router received frame other than UA in response to SNRM
Recommended Action Check the end station to see if the SNA stack is up and running
Error Message %SDLC-3-NULLPAK Interface NULL packet ptr rvr vs yr
Explanation An internal software error occurred in the routers SDLC processing system
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SDLC-4--SDLC_ERR SDLC_ERROR with no poii
Explanation protocol error was detected on secondary station but FRMR could not
be sent because the station did not own the poll bit This message indicates either poor line
conditions or faulty SDLC implementation
Recommended Action If the message recurs run traces on the SDLC line Copy the error
message exactly as it appears and report it to your technical support representative
Error Message %SDLC-4-UNKNOWNAD1JR Received input for unknown addr/input addr Tossing frame
Explanation SDLC frames were received from an unknown unconfigured SDLC address
Recommended Action Either configure the station for SDLLC or STUN or shut down
the serial interface to disable the line Copy the error message exactly as it appears and
report it to your technical support representative
228 System Error Messages SDLC Error Messages
Error Message %SDLC-4-WRONCADDR data from wrong address expected received
Explanation This condition typically occurs on multidropped lines when the Ti timer interval is too short or the sdlc line-speed command is not configured In rare cases the
RTS/CTS handshake can delay the transmission of frame so long that response is returned after the next station is polled
Recommended Action Adjust the value of the sdle line-speed statement in the configuration file Either take line traces to observe appropriate Ti timer intervals or
adjust empirically
Error Message %SDLC-6-XID_DISPLAY sa da ss ds 10
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message
%SDLC6XID_FOBMAT Unsupported XIIID format received format 10
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SDLC-4-XID_NOMATCH XID mismatch for CONNECTION REJECTED 10
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 229 SDLLC Error Messages
SDLLC Error Messages
Synchronous Data Link Control/Logical Link Control type translation error messages
Error Message %SDCLC-5-ACT_LINK SDLLC LINK address ACTIVATED
Explanation An SDLLC media conversion session was activated
Recommended Action No action is required
Error Message %SDLLC5-DACT_LINK SDLLC LINK address DEACTIVATED
Explanation An SDLLC media conversion session was deactivated If deactivation is
result of an error condition this message will include reason
Recommended Action If the message does not include description of an error the
deactivation was normal and the message is for information only If the message does
include description of an error begin problem analysis Determine whether session loss
isrelated to LLC2 timers by issuing the debug 1Ic2-cn command If the problem is related
to LLC2 timers consider using SDLLC with the local acknowledgment feature Copy the
error message exactly as it appears and report it to your technical support representative
Error Message %SDLLC6-XID DISPLAY sa da ss ds
Explanation This message supplies the information for the received and rejected XID
Recommended Action See also the SDLLC-6-XID_NOMATCH error message
230 System Error Messages SEC Error Messages
Error Message %SDLLC-XIQfORIvIAT Unsupported XID format received format
identification format received for this Explanation An inappropriate exchange XID was
mode of SDLLC operation Review the type of devices you are connecting with SDLLC to
make sure they are supported
Recommended Action See the SDLLC-6-XID_NOMATCH error message
Error Message %SDLLC-4-XID_NOMATCH XID mismatch for CONNECTION REJECTED
Explanation An inbound exchange identification XID from PU 2.0/PU 2.1 node was
rejected The targeted SDLC address is displayed The XID information is displayed in
subsequent messageSDLLC-6-XID_DTSPLAY or SDLLC-6-FORMAT
Recommended Action This is security feature Additional information is displayed to
help trace the source of the rejected XID If the message is undesirable simply remove the XID statement from the router configuration
SEC Error Messages
IP security error messages
Error Message %SEC-6-IPACCESSLOODP list packet
Explanation packet matching the log criteria for the given access list was detected
Recommended Action Informational message only No action required
System Error Messages 231 SEC Error Messages
Error Message %SEC-6-IPACCESSLOGNP list packet
Explanation packet matching the log criteria for the given access list was detected
Recommended Action Informational message only No action required
Error Message %SEC-6--IPACCESSLOCP list packet
Explanation packet matching the log criteria for the given access list was detected
Recommended Action Informational message only No action required
Error Message %SEC-3-NoMAx No default for NLESO defined
%SEC-2-NOOPT Box secured no option on internal packet
%SEC-2-NOTSEC First opt in tcb not BASIC security
%SEC-2-SECINS Security opt in tcb not SECINSERT
Explanation An internal software error occurred
Recommended Action If any of these messages recur copy the message exactly as it
appears and contact your technical support representative for assistance
Error Message %SEC-4-TOOMZNY Box secured too many options on internal packet
Explanation No room for all desired IP header options Packet discarded
Recommended Action Configure for fewer IP header options
232 System Error Messages SERVICE MODULE Error Messages
SERVICE MODULE Error Messages
This section contains error messages generated by the service module
Error Message %SERVICE_MODULE-4--ACCESSERROR Unit reports register access error
Explanation The Ti module supplied an incorrect register address new version of the
module might be operating with an old Cisco 105 software image
Recommended Action Update the Cisco lOS software image on the system If this action
does not solve the problem copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SERVICE_MCDULE4-azARMFAILURE Unit Could not access alan status disabling alan processing
Explanation The system issued an alarm interrupt but could not read the alarm status
register from the module As result the system disabled alarm processing
Recommended Action Copy the error message exactly as it appears and report it your
technical support representative
Error Message %SERVICE_M0DULE-4-BADTYPE Unit reports incompatible module type against router hw detect
the Explanation register read request returned an identity for module that was not
same as the identity reported by the router hardware pinout
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 233 SERVICE MODULE Error Messages
Error Message %SERVICE_MODULE-4-COMIVIANDFAILED Unit not ready/responding after register dec access command issued
Explanation The system did not receive ready signal within the allotted time after
writing to the command registet
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SERVICE_MODULEO-INITFAILURE Unit failed to create data structures used for module-access
Explanation The channel service unit/data service unit CSU/DSU driver failed to
This is The has crashed allocate memory for its data structures catastrophic enot system
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SERVICE_MODULE-4-INTERBYTETIMEOUT Unit timed out while byte dec of length register
Explanation The module took more than seconds to respond between bytes
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SERVICE_MODULE-3LOOPDOwNFAILED Unit WARNING Loopdown of remote unit failed
Explanation remote channel service unit/data service unit CSIJ is looping pings
and/or test patterns back to the system This error can be triggered if you disable loopback
tests on the remote CSU after placing the remote CSU into remote loopback state
Recommended Action Execute clear command on the remote CSU
234 System Error Messages SERVICE MODULE Error Messages
Error Message %SERVICE_MODULE-5-LOOPDOWNREMOTE Unit Remote loopback test cancel led
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative for assistance
Error Message %SERVICEMQDULE-5--LOOPUPFAILED Unit Loopup of remote unit failed
Explanation The loopback test on the remote unit failed The failure might indicate that the network connection is broken or that loopback tests are disabled at the other side
Recommended Action Check that the router is connected to the network Enable loopback tests on the remote unit If the problem persists copy the error message exactly as it appears and report it to your technical support representative
Error Message %SERVICE_MODULE-5-LOOPUPREMOTE Unit Remote unit placed In oopback
Explanation You executed loophack command on the remote unit The remote unit is now in loopback state
Recommended Action No action is required
Error Message %SERVICE_MODULE-4-NOTREAiJY Unit not ready for register access
Explanation The module was waiting for ready status before executing read/write request The system reported not ready status for seconds which caused the module to terminate the read/write request
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 235 SERVICE MODULE Error Messages
Error Message %SERVICE_MODULE-4-OLDIMAOE Unit router image older than module version access errors may be seen
Explanation The Cisco lOS software image does not recognize the programmable ROM
PROM software version number on the module The system displays this message if the
PROM has been upgraded to new version but the Cisco 105 software image has not been upgraded
Recommended Action Upgrade the Cisco 105 software image
Error Message %SERVICEMOIJULE-4-REPEATEDRESET Unit giving up after repeated resets couldnt bring module up again
Explanation The software issued several clear service-module requests to the module
The module did not respond to these requests
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SERVICE_MODULE-4-REQUESTOVERLOAD Unit module request overload lock access timeout
Explanation The system employs Cisco 105 scheduler semaphore object to ensure
mutually exclusive access across software threads to the channel service unit/data service
unit CSU/DSU thread had to wait for more than seconds on this semaphore
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SERVICE NODULE-B-RESET ReseLof Unit issued
Explanation This message indicates that the module was reset
Recommended Action No action is required
236 System Error Messages SLIP Error Messages
Error Message %SERVICE_MODULE-4-RESETFAILURE Unit failed to create reset process non-default module configuration may be lost
Explanation To reset the system the Cisco 108 software must initiate separate process The Cisco 108 software did not have sufficient memory to create this separate process The
module came up in an initialized state with the default configuration The user-defined
configuration might have been lost
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SERVICE_MODULE-4-UNKNOWNALARM Unit reports unknown network alarms alarm status reg
Explanation recent version of the module operating with an old Cisco 108 software
image did not recognize an alarm condition
Recommended Action Update the Cisco 108 software image on the system If this action
does not solve the problem copy the error message exactly as it appears and report it to your
technical support representative
SLIP Error Messages
Serial Line Internet Protocol error messages
Error Message %SLIP2-BAUQUOTE Impossible quoted character
%SLIP-2-BADSTATE Impossible input state
Explanation An internal software error occurred
Recommended Action If either of these messages recurs call your technical support
representative for assistance
System Error Messages 237 SMF Error Message
SMF Error Message
Software MAC filter error message
Error Message %SMF-3-NONEM failed to create St entry for on from chunk
Explanation The preallocated memory resources for the SMF have been exhausted
Recommended Action Reduce the number of interfaces on which transparent bridging is
configured Copy the error message exactly as it appears and report it to your technical
support representative
SMRP Error Messages
Simple Multicast Routing Protocol error messages
Error Message %SMRP-2--ASSERTFAILRD SMRP assertion failed
Explanation The software detected an inconsistency This is considered serious error be The router attempts to continue but SMRP processing may impaired
Recommended Action Copy the error message exactly as it appears noting any SMRP
problems that you are experiencing and report it to your technical support representative
Error Message %SIffiP--7-DEBUGMSG SMRP Debug
Recommended Action This message is generated by some debug commands to provide additional information about conditions in SMRP
Recommended Action If you are experiencing problems in SMRP these messages
should be provided along with any other information in report to your technical support
representative
238 System Error Messages SMRP Error Messages
Error Message %SDRP-5--NEIGHBOPDOWN SMRP neighbor down
Explanation neighboring SMRP router is now down
Recommended Action Notification message only No action required
Error Message %SMRP-6-NIEIGHBORUP SMRP neighbor up
Explanation neighboring SMRP router has appeared
Recommended Action Notification message only No action required
Error Message %SNRP-3-NOFDDICOMPAT SNRP port disabled pre-fdditalk not supported
Explanation SMRP cannot be started on an interface that is running pre-FDDITa1k
Recommended Action Use FDDITa1k on the FDDI ring if possible
Error Message %SMRP-5-PORTDOVN SMRP port down
Explanation An SMRP port is down and is no longer operational
Recommended Action Notification message only No action required
Error Message %SMRP-6-PORTUP SMRP port up
Explanation An SMRP port has come up
Recommended Action Notification message only No action required
System Error Messages 239 SNAPSHOT Error Messages
SNAPSHOT Error Messages
Snapshot dial-on-demand routing error messages
Error Message %SNAPSHOT-2--BAJJSTATE Bad state or Snapshot block location
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SNAPSHOT-2-NOMEXJRY Unable to create Snapshot SAB Updates will NOT be sent
Explanation The router is running out of memory which impacts the operation of snapshot
Recommended Action Check memory usage of the router Copy the error message
exactly as it appears and report it to your technical support representative
Error Message %SNAPSHOT-2-TOOMANYDIALERS Exceeded maximum dialer interfaces to watch Ignoring
Explanation Snapshot is being used over more than 100 DDR interfaces
Recommended Action Do not use snapshot over more than 100 DDR interfaces
240 System Error Messages SNMP Error Messages
SNMP Error Messages
Simple Network Management Protocol error messages
Error Message %SNMP-4-NOTRAPIP SNMP trap source has no ip address
Explanation The user entered an snmp-servcr trap-source command The interface
associated it requested for use as the source address has no address with The SNMP trap
is being sent anyway but without the source address that the user intended
Recommended Action There are two possible solutions Either enter no snmp-server
trap-source command to disable the request for specific source IP address or add an IP
address to the interface referenced in the snmp-server trap-source configuration command
Error Message %SNMP-3-SOCKET cant open UDP socket
Explanation The SNMP server was unable to open port for receiving SNMP requests
This usually happens when the SNMP server is started using the snmp-server community
configuration command on router or communication server with an interface that has no
IP address configured Another possible cause is low memory
Recommended Action Configure at least one interface with an IP address or specify the
no snmp-server command to remove the SNMP server process Call your technical add support representative if problems persist or if it becomes necessary to memory
System Error Messages 241 SSE Error Messages
SSE Error Messages
Silicon switching engine error messages
Error Message %SSE3-BADMEMORY SSE memory failure detected
Explanation memory error occurred
Recommended Action Copy the error message exactly as it appears and report it to youi
technical support representative
Error Message %SSE1---BOGUSEQ SSE bogus equal branch
Explanation An internal inconsistency in the data structures used by the SSE occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SSE-2-BOCUSEQ SSE bogus equal branch
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SSE-6-COMPERR SSE compilation failure --
Explanation software failure occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
242 System Error Messages SSE Error Messages
Error Message %SSE-2-HUNG SSE hung --
Explanation The SSE is hung
Recommended Action Reboot the SSE
Error Message %SSE-2-HWFAILURE SSE hardware failure-- code
Explanation hardware error occurred indicating an unexpected condition on the silicon switch processor SSP board
Recommended Action It might be necessary to replace the SSR Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SSE-2-NEMERROR SSE memory failure address expected got
silicon switch Explanation hardware enor occurred indicating memory failure on the processor SSP board
Recommended Action It might be necessary to replace the SSP Copy the error message
exactly as it appears and report it to your technical support representative
Error Message %SSE-l-NESTADiJR SSE nested addresses detected protocol
Explanation An internal inconsistency in the data structures used by the SSE occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 243 SSE Error Messages
Error Message %SSE-2-NIESTADDR SSE nested addresses detected protocol
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SSE-l--NOMATCH SSE delete didnt end at match node type value address bytecount high state
Explanation An internal inconsistency in the data structures used by the SSE occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SSE-2-NOMATCH SSE delete dldnL end at match node type value address bytecount high
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SSE3--NOMEMORY No memory available for
Explanation An operation could not be accomplished because of low memory condition
demands If Recommended Action Reduce other system activity to ease memory
conditions warrant upgrade to larger memory configuration
244 System Error Messages STANDBY Error Messages
Error Message %SSE2-NOTZERO Program memory does not start at zero
Explanation hardware error occurred indicating an unexpected condition on the silicon
switch processor SSP board
Recommended Action It might be necessary to replace the SSP Copy the error message
exactly as it appears and report it to your technical support representative
Error Message %SSE-2-SWPAILURE SSE software failure --
Explanation software failure occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
STANDBY Error Messages
Hot Standby Router Protocol error messages
Error Message %STNJDBY-3-BADAUTH Bad authentication from remote state
Explanation Two routers participating in the Hot Standby protocol disagree on the valid
authentication string
Recommended Action Use the standby authentication interface command to repair the local and the Hot Standby protocol authentication discrepancy between the system one
whose IP address is reported
System Error Messages 245 STANDBY Error Messages
Error Message %STANDBY3-MISCONFIG Attempt to change MAC address to when DECNET already running
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %STANDBY-3--NOEUFFER No buffer available or sending HELLO
Explanation The Hot Standby protocol software was unable to allocate packet buffer
The system may be out of memory
Recommended Action Record the output from the following commands show proc mem repeated twice show meni show buffers show version write terminal Provide
this information to your technical support representative
Error Message %STANIJBY3-NOMEMORY No memory available for
Explanation The system was unable to initialize the Hot Standby protocol on an interface The system may be out of memory
Recommended Action Record the output from the following commands show proc mem repeated twice show mem show version write terminal Provide this information to your technical support representative
Error Message %STANDBY3-NOSOCIKET Unable to open socket
Explanation The system was unable to initialize an IP connection for the Hot Standby protocol
Recommended Action Make sure that there is at least one interface configured to run IP
246 System Error Messages STUN Error Messages
STUN Error Messages
Serial tunneling error messages
Error Message %STIJN-3-BADCONN CONN bad connection peer
%STUN-3-BADLEN0P bad len or unknown op
op len
%STUN-3-BADMAGIC wrong magic mine theirs
%STtJN3-BAIJMAGICTCP peer wrong magic mm theirs
%STCN-3--BADPASSIVEOPEN passive open from failed
%STUN3-CONNILLSTATE CONN Peer illegal state
Explanation An internal software error occurred
Recommended Action If any of these messages recur copy the message exactly as it
appears and contact your technical support representative for assistance
Error Message %STUN-6-CCNNOPENFAIL CONN peer open failed
Explanation An attempt to connect to remote TCP STUN peer failed
Recommended Action Verify that the remote peer is accessible from this router that it is
running software capable of supporting STUN and that it is configured correctly
System Error Messages 247 STUN Error Messages
Error Message %STUN-6--ERR op len
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears for assistance and contact your technical support representative
Error Message %STUN-2-NOBUF Interface no buffer available to
the that the command Explanation memory shortage existed at time configuration was
issued This condition is rare and under normal conditions temporary
Recommended Action Reconfigure the STUN group If memory shortages persist call assistance your technical support representative for
Error Message %STUN3-NOINPIDB Input 1db not set 10
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %STUN-3-NOPROThEM No memory for STUN protocol definition of
Explanation The system does not have sufficient memory to define new STUN schema
Recommended Action This error message should only print when the router is critically
short of memory Copy the error message exactly as it appears and report it to your
technical support representative
248 System Error Messages STUN Error Messages
Error Message %STUN-3-NOTGEM No memory or STUN protocol sdlctg definition
Explanation software en-or occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %STUN-2-NOTGI Please remove and redefine protocol group
Explanation An internal error occurred The configuration is irregular
Recommended Action Remove and reconfigure the STUN protocol group Record the configuration and call your technical support representative for assistance
Error Message %STUN-6-OPENED peer opened state
%STUN-6-OPENINC CONN opening peer
%STtJN6--PASSIVEOPEN passive open
Explanation connection attempt to remote peer completed successfully OPENED
PASSIVE-OPEN or is in the process of being opened OPENING This is good expected behavior
Recommended Action Informational message only No action required
Error Message %STUN-6--PEERSHUTDOWN shutting down peer on
result Explanation connection to remote peer is being shut down This is typically the behavior of user intervention in STUN reconfiguration or disabling This is good expected
Recommended Action Informational message only No action required
System Error Messages 249 STUN Error Messages
Error Message %STUN-4-PEERSTATE Peer wrong state
Explanation An internal software error occurred
the Recommended Action If this error recurs copy error message exactly as it appears
and contact your technical support representative for assistance
Error Message %STUN6-RECONNECT PHJDR reconnect from peer
Explanation remote peer reestablished connection to this router
Recommended Action Informational message only No action required
Error Message %STCIJ3--SENDPUNT sent to
%STUN-3SENDPtJNTTCP sent to
Explanation An internal software error occurred
Recommended Action If either of these messages recurs call your technical support
representative for assistance
Error Message %STUN6-TCPFINI peer cosed state
Explanation remote peer closed STUN connection with this router
Recommended Action Examine the other router to see why it closed this connection with
this peer This can be caused by normal events such as reconfiguration
Error Message %STUN-TCPPEERSHUT
Explanation This route closed STUN connection with remote peer
Recommended Action Examine this router to see why it closed this connection with this
peer This can be caused by normal events such as reconfiguration
250 System Error Messages SUBSYS Error Messages
SUBSYS Error Messages
Software subsystem error messages
Error Message %SUBSYS-2-BAJJCL1ASS Bad subsystem class ignoring subsystem
Explanation software consistency check failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SIJBSYS2BADSEQUENCE Subsystem has cross-class sequence for
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SUBSYS-2-BADVEIRSION Bad subsystem version nuier ignoring subsystem
Explanation software consistency check failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SUBSYS-2-MISMATCH Kernel and subsystem version differ
Explanation software consistency check failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 251 SYS Error Messages
Error Message %SUBSYS-2-NOTFOUND Subsystem needs subsystem to start
Explanation software consistency check failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SUBSYS-2-RECURSION Maximum sequence depth exceeded by
Explanation software or hardware error occulTed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
SYS Error Messages
Operating system error messages
Error Message %SYS-2-ALREADYFREE Butter already in tree pooi
%SYS3-BADBLOCK Bad block pointer
%SYS-3-BADDISP Sad dispose code in
%SYS-3--.BADFREEM1GIC Corrupt free block at magic
Explanation block of memory is corrupt at the indicated location
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
252 System Error Messages SYS Error Messages
Error Message %SYS2-BADBUFFER Attempt to use buffer as ptr p001
Explanation hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-3-BADFREEPTRS Bad pointer at
Explanation pointer in the block header at the indicated location is corrupt
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %SYS-3-BADLINKTYPE Unexpected linktype
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-2H3ADLIST Regular expression access check with bad list
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 253 SYS Error Messages
Error Message %SYS-3-BADT4ACIC Corrupt block at magic
Explanation The free memory pooi is corrupted
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYS-3--BADPABAM Function value passed in parameter
Explanation software error occurred
Recommended Action Copy the error nwssage exactly as it appears and report it to your
technical support representative
Error Message %SYS-2-BAJJPID Bad pid for tty
%SYS-2--BADPOOL Attempt to return buffer with corrupt pool pointer ptr pool
%SYS-2-BADPOOLI4AGIC Attempt to use pool pointer with corrupt header pooi %SYS-2-BADSHARE Bad sharecount in ptr %SYS-2-BADSTACK Process has trashed stack old size
%SYS-6--BLKINFC words alioc RZ offset dealloc rfcnt
%SYS-2---CFCRKLEV cfork at level
Explanation An internal software error occurred
Recommended Action If any of these messages recur copy the message exactly as it for assistance appears and contact your technical support representative
254 System Error Messages SYS Error Messages
Error Message %SYS3-BADPRINT Process has no associated tty in 1OONESEC
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-3-BADPRCCESS Bad process ID when process table
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-3-BADRESID Clock hardware returned bad residual
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS2BLOCKHUNG Task hung with blocking disabled value Ox NOBLOCK_LIMIT
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 255 SYS Error Messages
Error Message %SYS2-CFORKLEV process create of failed at level 3QoSEC
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYS-2--CFORKMEM process create of failed no memory 30ONESEC
Explanation No memory was available to create process
Recommended Action If you suspect memory leak copy this message exactly as it
If leak does not appears and report it to your technical support representative memory
is available the additional appear to be the problem ensure that more memory to support features
Error Message %SYS-2-CHUNXHOUNDS Attempted to exceed freelist chunk bounds chunk data
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYS-2-CHUNKFREE Attempted to free non-chunk memory chunk data 10 ONESEC
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
256 System Error Messages SYS Error Messages
Error Message %SYS-2--CHUNKPARTIAL Attempted to destroy partially full chunk chunk
10 ONESEC
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-2-CHYJNKSIBLINGS Attempted to destroy chunk with siblings chunk
10 ONESEC
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-5-CONIFIG Configured from by
%SYS--5-CONFIGj Configured from by
%SYS5-CONFIGj Configured via L1M from
%SYS5-CONFIG_M Configured via MOP from by
Explanation The routers configuration was changed
Recommended Action Notification messages only No action required
Error Message %SYS-2-CONFIG DOWNFAlL Generated configuration not downward compatible
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 257 SYS Error Messages
Error Message %SYS-4--CONFIG NEWER Configurations from version may not be correctly understood
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYS5-CONIFIG_NV Non-volatile store configured from by
%SYS-5-CONEIG_NVJr Non-volatile store configured via MOP from by
Explanation The configuration was written successfully through the Maintenance Operation Protocol MOP
Recommended Action No action required
Error Message %SYS-3-CONFIG_NVEPR Non-volatile store write error configuration failed
Explanation The write of the nonvolatile configuration failed
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %SYS-3--CPUHOG Task ran for msec Process PC
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
258 System Error Messages SYS Error Messages
Error Message %SYS-3-DMPMEM
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-4-DUAL_MESSAGE SNMP system message request denied due to pending job
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYS-2-DUPEXPCRT Duplicate export vector registration attempt
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears for and contact your technical support representative assistance
System Error Messages 259 SYS Error Messages
Error Message %SYS-2-FREEBAD Attempted to free memory at not part of buffer pool
%SYS-2-FREEFREE Attempted to free unassigned memory at alloc dealloc
%SYS-2-GETBUF Bad getbuffer bytes
%SYS-3-HARIKARI Process top-level routine exited
%SYS-2-HEADER Attempt to return buffer with invalid buffer header ptr
Explanation An internal software error occurred
Recommended Action If any of these messages recur copy the message exactly as it for assistance appears and contact your technical support representative
Error Message %SYS-2-INLIST Buffer in list ptr
%SYS2-INLIST1 Buffer in list ptr cailer
%SYS2-INPUTQ INPUTQ set but no idb ptr
%SYS-2-INSCHED within scheduler
%SYS-2-INTSCHED at level
%SYS3-INUSEFREE Block on free list in use
Explanation An internal software error occurred
the it Recommended Action If any of these messages recur copy message exactly as
appears and contact your technical support representative for assistance
260 System Error Messages SYS Error Messages
Error Message %SYS-3-INTPRINT Illegal printing attempt from interrupt level 1UONESEC
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-4-INVALIDIMAGE Running invalid image for platfonn
Explanation The software image being run is for different hardware architecture This problem can occur on Cisco 1003 Cisco 1004 or Cisco 1005 The Cisco 1003 and Cisco 1004 have different image from the Cisco 1005
Recommended Action Install the correct software image
Error Message %SYS-3INVMEMINI Invalid memory action at interrupt level
Explanation This message indicates that memory allocation or deallocation was
attempted from an interrupt handler
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
System Error Messages 261 SYS Error Messages
Error Message %SYS-2--LINKED Bad enqueue of in queue
%SYS-2--LINKED Bad p_dequeue of in queue
%SYS-2-LINKEIJ Bad prequeue of in queue
%SYS-2-LINKBD Bad requeue of in queue
%SYS-2---LOWMEM Low memory debug exception limit free
Explanation The router is running short on memory
Recommended Action It may be necessary to free some memory by exiting program
it and If this error recurs copy the error message exactly as appears contact your technical
support representative for assistance
Error Message %SYS2-MALLOCFAIL hemory allocation of bytes failed front pool alignment
Explanation The requested memory allocation is not available from the specified memory
pool The current system configuration network environment or possibly software error might have exhausted or fragmented the routeis memory
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYS-5-MEMDIJNP
Explanation This message is sent in conjunction with the %SYS6-BLKINFO
message It provides additional data
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
262 System Error Messages SYS Error Messages
Error Message %SYS-3--MGDTIFER timer 10 ONESEC
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-3-MODTIMEREXP Unknown timer expiration timer type 10 ONESEC
notice for timer that Explanation The process received an expiration does not belong to it
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-3--MSGLOST messages lost due to queue overflow
Explanation software error occurred
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message
%SYS6-MTRACE addr pc
Explanation The free memory pool is corrupted
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
System Error Messages 263 SYS Error Messages
Error Message
%SYS-2-NOBLOCK II with blocking disabled
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %SYS-6-NOBRIUGE Bridging software not present
Explanation Your system is not equipped to be bridge
Recommended Action Install the bridging software option
Error Message %SYS-1-NOECO WARNING This 500-CS cannot run this version of software Please contact Customer Service for upgrade information tele 800 553-NETS 415 903-7208 email [email protected] Hardware burned in address is
Explanation An Error Change Order ECO is needed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYS-2-NOMEMFRG Memory fragmentation check debug exception fragment size
Explanation The system detected an error checking memory fragmentation
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
264 System Error Messages SVS Error Messages
Error Message %SYS-2--NONEMORY No memory available for
Explanation An operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If conditions warrant upgrade to larger memory configuration
Error Message %SYS-3-NOPROC Process table full
%SYS2-NOTDEAD Rekilling process pid
%SYS-2-NCTQ p_unqueue didnt find in queue
%SYS-2-NOTQ unqueue didnt find in queue
%SYS-3-NTJLLIDB Null 1db in
Explanation An internal software error occurred
Recommended Action If any of these messages recui copy the message exactly as it appears and contact your technical support representative for assistance
Error Message %SYS-2---NOPROCESS No such process
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %SYS-3-NZREFCNT Block on free list with ref count
Explanation block of memory in the free pool is actually in use The number of
the block is indicated processes using memory
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
System Error Messages 265 SYS Error Messages
Error Message %SYS-5OUTSETUP Configuration file accepted aborting setup
Explanation configuration was accepted through the network so the setup session will be aborted
Recommended Action No action required
Error Message %SYS-3--OVERRUN Block overrun at redzone
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %SYS-l-OVERTEMP System detected OVER TEMPERATURE condition Please resolve cooling problem immediately
Explanation The environmental monitor detected high temperature condition
Recommended Action Make sure that the room temperature is not too high and that air
flow to the card is not blocked If this condition persists the environmental monitor might
shut the system down Call your technical support representative for assistance if
necessary
Error Message %SYS-2-PAKCLIP Bad pak_clip bytes
Explanation software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
266 System Error Messages SYS Error Messages
Error Message %SYS-6--PROCINFO Process just finished executing
Explanation This message is an auxiliary to the SYS-3 -OVERRUN and
SYS-3-BADMAGIC error messages It indicates the process or process fragment that was executing at the time of the errot
Recommended Action Copy this messages exactly as it appears and report it along with the SYS-3-OVERRUN and SYS-3-BADMAGIC error messages to your technical support representative
Error Message %SYS-2-QCOUNT Bad dequeue count
%SYS2-QCOUNT Bad pdequeue count
%SYS2--QCOUNT Bad p_unqueue count
%SYS-2QC0UNT Bad unqueue count
%SYS-2--QINSERT Unable to add to queue no elements
%SYS-4-REGEXP
Explanation An internal software error occurred
Recommended Action If any of these messages recur copy the message exactly as it for assistance appears and contact your technical support representative
Error Message %SYS3-REGARG Registry service has too many arguments
%SYS3-REGCREA2 Attempt to create registry service twice
%SYS3-REGDFLT Attempt to add default twice to registry service
%SYS-3-REGNONE Registry service doesnt exist
%SYS-3-REGTYPE Registry service is wrong type should be
Explanation An internal software consistency check failed
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 267 SYS Error Messages
Error Message %SYS-5-RELOAD Reload requested
%SYS-5-RESTART System restarted --
Explanation reload or restart was requested
Recommended Action Notification messages only No action required
Error Message %SYS-4-RELOADj.TTEMPT Attempt via SNMP failed system-shutdown not configured
Explanation software error occurred
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
268 System Error Messages SYS Error Messages
Error Message %SYS-2-RETBUF Bad retbuffer ptr
%SYS-2-RETBUF1 Bad retbuffer ptr caller
%SYS-2-SELF s_setblock on own process
%SYS-2-SELFLINXED Buffer linked to itself in free pool
%SYS2-SHABED Attempt to return buffer with sharecount ptr
%SYS-2-SHARED1 Attempt to return buffer with sharecount ptr caller
%SYS-3-SOCKCI1KN Unknown socket protocol
%SYS-2--SPEC Trying to set unknown special character to
%SYS-6-STACKLOW Stack for running low
Explanation An internal software error occurred
Recommended Action If any of these messages recur copy the mesage exactly as it appears and contact your technical support representative for assistance
Error Message %SYS-2-SMASHED Smashed block at 40850 next prey size 3580000 Process Init level5
Explanation An internal software error occulTed
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message %SYS-2-SMASFIEDINFO Smashed block last freed allocated by 30000 name
Explanation software error corrupted the memory
Recommended Action Copy the message exactly as it appears and report it your technical support representative
System Error Messages 269 SYS Error Messages
Error Message %SYS-4-SNMP_HOSTCONFIGSET SNI4P hostconfigset request Loading configuration from
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYS-4-SNMPNETCONFIGSET SNMP netconfigSet request Loading configuration from
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYS-4SNMP_WRITENET SNMP WriteNet request Writing current configuration to
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYS-2-SNMPOIDX Attempt to snmpidb with ifjindex of
Explanation software error occurred
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
270 System Error Messages SVS Error Messages
Error Message %SYS3SUPNONE Registry doesnt exist
Explanation software error occurred
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message %SYS2-SUPNOT Cant create Registry
Explanation An internal software consistency check failed
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message %SYS2-SUPTWICE Attempt to create Registry again 30 ONESEC
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-5-TABLEERR table damaged
Explanation An internal table entry became corrupted
Recommended Action Copy the message exactly as it appears and report it your technical support representative
System Error Messages 271 SYS Error Messages
Error Message %SYS-6-TESTINFO Scheduler test for just executed
Explanation This message is an auxiliary to the SYS-3-UVERRUN and
SYS-3-BADMAGIC error messages It indicates which process or process fragment was
executing at the time of the error
Recommended Action Copy this message exactly as it appears and report it along with
the SYS-3-OVERRUN and SYS3BADMAGIC error messages to your technical
support representative
Error Message %SYS-3-TI Timer callback ran long PC lOONESEC
Explanation software error occurred
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
Error Message %SYS3-TIMEBNEC Cannot start timer with negative offset 10 ONESEC
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYS-3TTYNEM Tty no memory to save tty default parameters
Explanation The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If conditions warrant upgrade to larger memory configuration
272 System Error Messages SYS Error Messages
Error Message %SYS-2-WATCHDOG Process aborted on watchdog timeout Process ONESEC
Explanation The indicated process ran for such long time without relinquishing the killed processor that the system it as runaway
Recommended Action If this error recurs call your technical support representative for assistance
Error Message %SYS3-WRONGFREELIST Block size on wrong free list
Explanation freed buffer was placed on the wrong list of free buffers
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %SYS-2--WRONGPOOL Buffer found in pool should be in pool
Explanation software error occurred
Recommended Action Copy the message exactly as it appears and report it your technical support representative
System Error Messages 273 SYSMGT Error Messages
SYSMGT Error Messages
System Management error messages
Error Message %SYSMGTjPC-3-IPC_ERROR SYSMGT RPC IPC failed
Explanation The Channel Interface Processor CIP card network management event
processing subsystem failed to set up the Interprocess Communications port Network management events will not be processed from installed CIP cards
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYSMGT_RPC-3 -NEThIGT_EVENT SYSMGT RPC NEThGT Event
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYSMGT SNALLC-3-EVENT ERROR SYSMGT SNA LLC
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
274 System Error Messages TAC Error Messages
TAC Error Messages
Terminal Access Controller Access Control System TACACS protocol error messages
Error Message %TAC-6-SENDThO Send type to timed out
Explanation background TACACS notification enabled with the command tacacs
notify was not acknowledged by the TACACS server processor within the timeout period minutes The information contained in that notification was lost This loss of
information may interfere with accounting or auditing on the server
This condition arises when the TACACS server is misconfigured crashed or became unreachable via the network
Recommended Action Check the TACACS server and the network attached to it
Error Message %TAC-4--U1JEXBEP Reply for non-existent request on queue
Explanation The TACACS facility received message it was not expecting This may
occur when TACACS server sends duplicate responses or when it responds to request
that has already timed out It also may be due to an internal software problem
it Recommended Action If this error recurs copy the error message exactly as appears
and contact your technical support representative for assistance
System Error Messages 275 TBRIDGE Error Messages
TBRIDGE Error Messages
Transparent bridging error messages
Error Message %TBRIDGE-4-GIANT Giant received on exceeds DA SA ONESEC
Explanation packet was received that exceeds the expected maximum transmission four unit MTU length for the receiving interface The first bytes of the packet following
the source address are also provided to assist diagnosis
Recommended Action Use the address and packet information provided to trace the
source of these packets and reduce its MTU to conform to the standard for the given media
Error Message %TBRIDGE-4--INVALIDMEDIA Invalid media encountered for bridging
Explanation Transparent bridging was configured on an interface that does not support it
Recommended Action Remove transparent bridging from the configuration on the
specified interface
Error Message %TBRIDGE-4-NGNEMORY No memory available for transparent bridging
Explanation Packet memory was exhausted to the point that the few static buffers
required for transparent bridging cannot be allocated
Recommended Action Diagnose memory utilization using the show buffers and show memory commands
276 System Error Messages TBRIDGE Error Messages
Error Message %TBRIDGE-4-NOVCDROP Destination VC unknown for packet ONESEC
Explanation transparently bridged packet destined for an ATM interface cannot be fully addressed
Recommended Action Clear the bridge table to force re-learning of all addresses
Error Message %TERIDGE-4-NOVCFLOOD No VCs configured for bridging on ONESEC
Explanation An ATM interface was configured for transparent bridging without also specifying the associated virtual circuits
Recommended Action Configure the required virtual circuits on the specified interface
Error Message %TBRIDGE-4SMF ACTION invalid action found for on ONESEC
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
System Error Messages 277 TCP Error Messages
TCP Error Messages
Transmission Control Protocol error messages
Error Message %TCP-2--ACCEPT Callback failed to accept cormection from to -- discarding
Explanation An internal software error occurred
Recommended Action If this message recurs copy it down exactly as it appears and
contact your technical support representative for assistance
Error Message %TCP-6-BADAUTH MD5 digest from to
Explanation The system received TCP packet with an invalid MD5 authentication
digest on connection endpoint The message ends with the string RST if the incoming packet was TCP reset packet
Recommended Action Determine why the source of the packet is not generating correct
digests on the connection This could be due to either misconfiguration or security weaknesses
Error Message %TCP-2-BUFFER Tty buffering bug %TCP2-PUTBYTE Tty tcp_putbyte with blocking disabled
Explanation An internal software error occurred
Recommended Action If either message recurs call your technical support
representative for assistance
278 System Error Messages TCP Error Messages
Error Message %TCP-2-NOTREADY called but TCP not initialized
Explanation An internal software error occurred
Recommended Action If this message recurs copy the message exactly as it appears and contact your technical support
Error Message %TCP-6-NOTREAiJY called but TCP not initialized
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %TCP-6-TOOBIC Tty too many bytes of options
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
System Error Messages 279 TMQ Error Message
TMQ Error Message
Inbound terminal port queuing error message
Error Message %TMQ-3--NOTFOUNIJ ThIQ Attempt to delete entry not in queue
Explanation An attempt was made to delete an entry not in the queue
Recommended Action Advisory message only No action required
TN Error Messages
Telnet error messages
Error Message %TN2-BADLCGIN Bad login string pointer
%ThT-3-BADSTATE Illegal state
%TN-3-READLINE Unknown return code from telnet_readline
Explanation An internal software error occurred
Recommended Action If any message recurs call your technical support representative for assistance
280 System Error Messages TN3270 Error Message
TN3270 Error Message
TN3270 error messages relate to the TN3270 protocol variation of the IBM VT virtual
terminal protocol
Error Message %Th3270-2-INP_OVIF1 Input Buffer overflow
Explanation problem in TN3270 protocol was detected Eight KB 8192 bytes of data
were received without TN3270 end-of-packet indicator The TN3270 buffer overflowed
Recommended Action Copy this error message exactly as it appears and contact your
technical support representative for assistance
TR Error Messages
Token Ring error messages
Error Message %TR-3--ADPCHK Interface adapter check error
Explanation The Token Ring monitor firmware detected fatal error on the interface card
Recommended Action Issue clear interface command If this error recurs copy the
error message exactly as it appears and contact your technical support representative for
assistance
Error Message %TR-3-ASYNCUSE Unit async in use
Explanation Another internal process is communicating with the given Token Ring
interface
Recommended Action Wait minute and try again If the condition persists it probably
indicates an internal software error Copy the message exactly as it appears and report it
your technical support representative
System Error Messages 281 TR Error Messages
Error Message %TR-4-BADADAPT Unit adapter not responding
Explanation Token Ring interface is not responding to initialization
Recommended Action Confirm the Token Ring cards configuration and make sure it is
in the correct slot If the interface is in the correct slot this message indicates probable
hardware failure the it it technical Copy message exactly as appears and report your
support representative
Error Message %TR-3-BADBRDGPARMS Unit bad bridge parameters bridgenum max_rd \nthisring targetring
%TR-3-BPJJBtJFFSIZE Unit bad buffersize
%TR-3 -BADFIRM Unit Tokenring firmware download failed\n got expected at address
%TR-3-BADFJRNTYPE Unit bad firmware type code during type4hex fw %TR-3-BADFUNC Unit bad functional address ring mode
Explanation An internal software elTor occurred
Recommended Action If any of these messages recur copy the message exactly as it
appears and contact your technical support representative for assistance
Error Message %TR-3-BADHEADER RX Unit type size use flags
Explanation The system detected corrupted data from the Token Ring interface card CSC2R/1R and CSC-R16M only There may be hardware problem
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
282 System Error Messages TR Error Messages
Error Message %TR3--BADMUL Unit Cant set TR address to hardware multicast address
Explanation An attempt was made to set the Token Ring interface MAC address to reserved multicast address
Recommended Action Check your configuration Make sure that your XNS and/or
Novell Token Ring addresses have not inadvertently been set to reserved multicast addresses
Error Message %TR3-BADRNCNUN Unit ring number doesnt match established number
Explanation The number you have configured for the local ring does not match the value
currently in use on the ring
Recommended Action Check the configuration to make sure you used the correct ring
number If it is correct confirm the configuration of all other bridges on the ring to make
sure they are using the same ring number
Error Message %TR-3-BADSLOT Unit Slot does not exist
the Cisco 4000 It is when software Explanation This error message pertains only to seen
tries to access discover network interface module NIM that is not in slot or The This could indicate card software stalls trying to access the nonexistent slot message
error
Recommended Action If this message recurs call your technical support representative
for assistance or replacement card
System Error Messages 283 IR Error Messages
Error Message %TR-3-BADSTART Unit Start completion and wrong idb state state
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %TR-3-BADUNIT Bad unit nuniber
Explanation This error message pertains only to the IGS When displayed it indicates
that the system cannot find the chipset registers where it expects them to be This is most
likely hardware error
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance It will be necessary to
determine the hardware unit configuration
Error Message %TR-4-BKGND Unit bkgnd Int last packet out
%TR4-BKGNDINT Unit bkgnd int
Explanation An internal software error occurred
Recommended Action If either of these messages recur call your technical support
representative for assistance
Error Message %TR3--BOGUSDATA
Explanation This message displays the first eight bytes of frame data if the data length is
invalid It is the second part of the %TR-3-BOGUSLENGTH error message that follows
Recommended Action See recommended action for the %TR-3-IBOGIJSLENGTH
error message
284 System Error Messages TR Error Messages
Error Message %TR-3-BOGUSLENGTH Unit bad input length code
Explanation This is the first message displayed when the frame data length is invalid It is unique to the CSC-R16 Token Ring card for all system versions
Recommended Action Display of both the %TR-3-BOGUSLENGTH and
%TR-3-BOGUSDATA error messages indicates serious problem on the interface between the Token Ring chipset the SBE16 card and the system drivet Copy the message exactly as it appears and report it your technical support representative
Error Message %TR-3-COMPFAIL Unit Tbuf completion failure result
%TR-3--FILTFAIL Unit SRB filter set failed blk downing
%TR-3-GETCONF Unit get_config failed result
Explanation An internal software error occurred
Recommended Action If any of these messages recur copy the message exactly as it technical for assistance appears and contact your support representative
Error Message %TR-3-DIAGFAIL Interface failed mit diags
Explanation The microcode attempted to run its diagnosticis on the chip and failed
Recommended Action Issue clear interface command If this error recurs copy the
error message exactly as it appears and contact your technical support representative for
assistance
System Error Messages 285 TR Error Messages
Error Message %TR-3--INCON Unit incompatible firmware system
Explanation The Token Ring interface contains firmware that is incompatible with the
system software
Recommended Action Call your technical support representative to upgrade the Token
Ring Monitor firmware the system software or both
Error Message %TR-3-INITFAIL Unit mit failed result code error code
Explanation The Token Ring hardware failed to initialize properly
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %TR-4-INIPFAIL Unit interface failure state
Explanation The Token Ring Monitor firmware detected fatal error due either to an
internal software problem or to hardware failure
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
286 System Error Messages TR Error Messages
Error Message %TR-3--MADGETX Unit lost packet using Transmit Descriptor
Explanation This error message pertains only to the Cisco 4000 When displayed it indicates that packet was lost inside the Madge firmware and the software lbst the pointer to it
Recommended Action This message indicates software problem on the card If this message recurs call your technical support representative for assistance or replacement card
Error Message %TR-3-MOJEFAIL Unit change mode failed result code error code
%TR-3-MOIJFAIL Unit tramodify failed result
%TR-3--NOFIRM Unit no TMS3SO firmware present eagie magic
Explanation An internal hardware or software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %TR-3-NOMEMORY Unit no memory for
Explanation The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to case memory demands If conditions warrant upgrade to larger memory configuration
System Error Messages 287 TR Error Messages
Error Message %TR-4-NOMOREPAGES Unit Out of Pages for
Explanation This error message pertains only to the Cisco 4000When displayed it
indicates that the ability to switch the receive buffers for the Token Ring was halted due to an insufficient amount of memory
Recommended Action Reduce other system activity to ease memory demands and then
reset the Token Ring interface by entering clear interface tokenring command If these
actions do not solve the problem upgrade to larger memory configuration or call your
technical support representative for assistance
Error Message %TR-3--NOPAK Unit Tbuf completion and no pakout
Explanation An internal hardware or software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %TR-3-OLDTRIF Obsolete firmware in multibus TR unit does not support fast switching
Explanation firmware upgrade is needed
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
288 System Error Messages TR Error Messages
Error Message %TR-3-OPENFAIL Unit open failed check the lobe cable DB9 connection
Explanation The Token Ring interface was unable to insert itself into the ring This is an indication of busy or broken ring The first character string in this error message indicates the stage of initialization at which the error occurred and the second describes the erron
Recommended Action Try to open the interface again This generally can be accomplished by issuing the clear interface tokenring command If the error message for recurs call your technical support representative assistance
Error Message %TR-3-OPENFAIL2 Unit open failed check the lobe cable connection
Explanation The Token Ring interface was unable to insert itself into the ring and the error code returned indicates wiring problem
Recommended Action Check the cable connecting the router to the Token Ring MAT and try to open the interface again This generally can be accomplished by issuing the clear interface tokerning command If the error message recurs call your technical support representative for assistance
Error Message %TR-3-PANIC Unit panic
Explanation The Token Ring monitor firmware detected fatal error that indicates an impending interface failure
Recommended Action Copy the enor message and the interface message exactly as they appear and then report them to your technical support representative
System Error Messages 289 TA Error Messages
Error Message %TR3--PANICINF Unit P1
Explanation This message is similar to the %TR-3-PANIC error message but indicates
nonfatal errot This message appears in very unusual situations that should not arise in normal operation
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %TR3-PANICTYPE Unit error
Explanation This message is similar to the %TR3--PANIC error message but indicates
nonfatal errot This message appears in very unusual situations that should not arise in normal operation
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %TR3-RESETFAIL Unit reset failed error code
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %TR3-RESETFAIL2 Unit reset failed auxiliary processor mit failed
Explanation This message isolates particular RESETFAIL condition from several other
reset failure conditions It is unique to the CSC-R16 Token Ring card for all system versions and indicates state problem
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
290 System Error Messages TR Error Messages
Error Message %TR-3-RIFBADMAGIC Invalid magic number in RIF table entry
%TR-3-RIFTBLTFASH Trashed RIF table entry found and zeroed
Explanation An internal software elTor occurred
Recommended Action If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %TR-3-SETBRIDGEFAIL Unit set bridge failed code %x
Explanation hardware error occurred The source routing accelerator SRA chip on the Token Ring card could not be initialized
Recommended Action replacement card might be needed Copy the message exactly as it appears and contact your technical support representative for assistance
Error Message %TR-3-SFTFAIL Unit couldnt set interface to physical address
Explanation An illegal MAC address was specified for this interface
Recommended Action Normally the Token Ring interface uses the burned-in address contained in PROM on the board However certain protocol stacks require the MAC
for address to be modified to an illegal value Check your configuration possible problems technical If this message recurs call your support representative
System Error Messages 291 TR Error Messages
Error Message %TR-3--SETFUNFAIL Unit set functional address failed code
%TR-3SETGRPFAIL Unit set group address failed code
%TR3--SETOPTFAIL Unit set open options failed code
%TR3--SMTSTATFAIL Unit getsmt get smt stats failed result
Explanation An internal software error occurred
Recommended Action If any of these messages recur copy the message exactly as it
appears and contact your technical support representative for assistance
Error Message %TR-4-SNKBRIDG Unit removing invalid bridge
Explanation The system could not start Token Ring source-route bridge because the
interface in question does not have the appropriate Token Ring Monitor firmware or hardware
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
Error Message %TR-3-STARTFAILED Unit start failed result reason
Explanation The Token Ring Monitor firmware attempted to insert the system into the
ring and the chipset detected nonstandard fatal error
Recommended Action This message indicates problem with the Token Ring chipset
hardware Copy the message exactly as it appears and report it your technical support
representative
292 System Error Messages TR Error Messages
Error Message %TR3-STARTFAILED2 Unit start failed auxiliary processor mit failed
Explanation This error message isolates particular STARTFAIL condition from several
other reset failure conditions It is unique to the CSC-Rl6 Token Ring card for all system versions and indicates state problem
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message %TR-6-STATE TR Ring Status
Explanation This message is displayed when the Token Rings status changed as
determined by the chipset This information also is used to automatically determine
whether the interface is still usable to propagate network traffic
Recommended Action Informational message only No action required
Error Message %TR3STATFAIL Unit get_static get stats failed Async
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %TR-6--STATRING TR Ring Status LIV
Explanation This message is displayed when the Token Rings status changed as
determined by the chipset This information also is used to automatically determine
whether the interface is still usable to propagate network traffic The meaning of each status
code is shown in Table
Recommended Action Check the Token Ring for the indicated condition
System Error Messages 293 TR Error Messages
Table Token Ring Status Codes
Code Explanation Fatal
0x8000 Signal loss Yes
0x4000 Hard error Yes
0x2000 Soft error No
Oxi 000 Transmit beacon Yes
0x0800 Lobe wire fault Yes
0x0400 Auto removal error Yes
OxO 100 Receive request removed Yes
0x0080 Counter overflow No
0x0040 Single station No
0x0020 Ring recovery No
Error Message %TR-3--TRACMD tra_cmd unit bad state cmd bik lob
%TR4-UNKNOvNCOMP Unit Unknown coirrnand completoncmd rsit
%TR-3-UNKNUWNT2M Unit Unknown t2m command
Explanation An internal software error occurred
Recommended Action If any of these messages recur copy the message exactly as it
appears and contact your technical support representative for assistance
294 System Error Messages TUN Error Messages
Error Message %TR-3---WIREFAULT Unit wire fault check the lobe cable MAU connection
Explanation The Token Ring hardware is reporting wire fault condition
Recommended Action Check the cable connecting the router to the Token Ring media attachment unit MAU
TUN Error Messages
Tunnel error messages
Error Message %TUN-4-BALXDUThIODE Interface unsupported output mode
Explanation The tunnel interface was set to an encapsulation mode that is not supported
Recommended Action Report the problem to your technical support representative and
correct your configuration
Error Message %TUN4RECURDOWN temporarily disabled due to recursive routing
Explanation When routing the same payload protocol over carrier protocol tunneling
IP over IP for example it is possible to misconfigure your network so that you will try to
route to the tunnel destination address via the tunnel This is usually caused by
misconfiguration of the tunnel or temporary instability due to route flapping elsewhere in
your network It is important to take steps to ensure that routing information between the
carrier networks and the payload networks is not allowed to mix If the router discovers
recursive routing problem it will temporarily shut down the tunnel interface for few
minutes so that the situation that is causing this problem can resolve itself as routing
protocols converge If the problem is caused by misconfiguration the link may oscillate
indefinitely
Recommended Action No action required
System Error Messages 295 UCODE Error Messages
Error Message %TUN-4-RECURSHtJT administratively disabled due to recursive routing
Explanation If the recursive routing situation reported by the RECURDOWN message is
not cleared up after ten bounces the tunnel interface will be administratively shut down to
avoid further flapping
Recommended Action Determine the cause of the recursive routing situation correct it
and then manually bring the interface back up using the no shutdown command
UCODE Error Messages
Microcode error messages
Error Message %UCODE-3-BADCHKSUM Bad checksum in found expected
Explanation The microcode file is corrupted in some way the checksum computed after
reading the file from Flash does not match the one in the file The file will not be
downloaded and the onboard ROM microcode will be used instead
Recommended Action Reload the microcode If the message recurs call your technical
support representative for assistance
Error Message %UCODE-3-HADFIWVIER Ucode file requires version .x hardware
Explanation mismatch was detected during an attempt to load microcode file into an
interface processor The hardware requires different version than the one specified
Recommended Action Use the required microcode version
296 System Error Messages UCODE Error Messages
Error Message %UCODE-3-HIJRCORRUPT Ucode header corrupted in found expected
Explanation The microcode file is corrupted in some way the checksum computed after reading the file from Flash does not match the one in the file The file will not be downloaded and the onboard ROM microcode will be used instead
Recommended Action Reload the microcode If the message recurs call your technical support representative for assistance
Error Message %UCODE-3--IPCEUFFAIL Unable to obtain IPC resources
Explanation The InterProcess Communication IPC service used to download microcode to certain interface processors has failed to obtain buffer Certain interface load processors will not properly
Recommended Action Try the reload command again If this error recurs copy the error message exactly as it appears and contact your technical support representative for assistance
Error Message %UCOIJE3-IPCINITFAIL Unable to initialize IPC services
Explanation The InterProcess Communication IPC service used to download
interface initialize microcode to certain processors has failed to Certain interface processors will not load properly
Recommended Action Reload the routet
Error Message %UCODE-3-IPCINVALID Invalid IPC request received from
Explanation The InterProcess Communication IPC service used to download microcode to certain interface processors has received an invalid message
Recommended Action Verify that the proper revisions of code are selected
System Error Messages 297 UCODE Error Messages
Error Message %UCODE3-LDFAIL Unable to download ucode in slot installed ucode loaded
Explanation For some reason the microcode file specified by the configuration is not
suitable for downloading or another error occurred The onboard ROM microcode will be
loaded so the interface can remain operational
Recommended Action Attempt to reload the microcode If the message recurs call your
technical support representative for assistance
Error Message %UCODE-3-NOBUF Unable to allocate memory for ucode buffer
Explanation buffer is required to decompres microcode before loading it into an
interface processor This buffer could not be allocated for some reason
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
Error Message %UCODE-3-NOFILE Ucode file not found installed ucode loaded in slot
Explanation The file specified by the configuration was not found in Flash The onboard
ROM microcode will be loaded so the interface can remain operational
Recommended Action Use show flash to determine if the file is located in Flash If the
file is there attempt to reload the microcode If the message recurs call your technical
support representative for assistance
Error Message %UCODE-3-NOROM Invalid attempt to load RUM ucode in slot
Explanation Sonic interface processors cannot load microcode from ROM
Recommended Action Remove the erroneous configuration statement
298 System Error Messages UCODE Error Messages
Error Message %UCODE5-OBSOLETE FUDI unit has obsolete microcode please upgrade it
Explanation This message occurs when an FDDI interface processor is found running microcode that does not support microcode CMT which is required for all software releases from 102 on
Recommended Action Upgrade the microcode on the interface processot
Error Message %UCODE-3-OLDHARD Ucode file requires version hardware or later
Explanation The microcode specified requires more recent version of the hardware than it found The onboard RUM microcode will be loaded instead
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message %UCODE-3-RDFAIL Unable to read ucode file from flash
Explanation For some reason the microcode file was not read from Flash Flash might be locked by another process or otherwise unavailable
Recommended Action Use the show flash command to determine whether Flash is in use and issue another microcode reload when Flash is free If the message recurs call your technical support representative for assistance
Error Message %UCODE3--TOOBIG File at length is too long for buffer size
Explanation The file is too large for the buffer The onboard RUM microcode will be loaded
Recommended Action If the error message recurs after the onboard RUM microcode is loaded call your technical support representative for assistance
System Error Messages 299 UNIX Error Message
Error Message %UCODE-3-VERSIONCK Inappropriate version or
Explanation An attempt was made to load an inappropriate version of microcode
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
Error Message %UCODE-3WRONGHARD is ucode not microcode/hardware mismatch
Explanation The specified microcode file is for different interface processor than
specified in the configuration The user has made configuration error The onboard ROM
microcode will be loaded
Recommended Action Reenter your microcode configuration command after confirming
the interface type and reload the microcode
UNX Error Message
UNIX error message
Error Message %UNIX-i-SYSABORT System aborted
Explanation The system abnormally terminated
Recommended Action Record the output from the following commands
show process memory repeated twice
show memory
show buffers
show version
show running-config
Provide this information and the error message to your technical support representative
300 System Error Messages UTIL Error Messages
UTIL Error Messages
Utility error messages
Error Message %UTIL-3-RkNGEINCON internal inconsistency
Explanation fatal software error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %UTIL-2-RANGERET list no memory cant return range
Explanation memory overflow error occurred
Recommended Action Investigate memory usage If memory usage is abnormal call
your technical support representative for assistance Otherwise increase router memory
Error Message %UTIL-2--BANGEDUP list already contains range
Explanation software error occurred
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
Error Message UTIL-3-RANGEINVERT list low high
Explanation software error occurred
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
System Error Messages 301 VINES Error Messages
Error Message %TJTIL-3-RANCENULLINPUT null pointer input to range function
Explanation An attempt was made to access range function with NULL pointer
The range list creation failed
Recommended Action Review the error log for colTesponding memory allocation
failed message Copy the error message exactly as it appears and report it to your technical
support representative
Error Message %UTIL-3-TREE Data structure error- ONEMIN
Explanation software error occurred resulting in data structure inconsistency
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative Ask for their assistance in obtaining version of code with
the error fixed
VINES Error Messages
Banyan Virtual Integrated Network Service error messages
Error Message %VINES-2--BADPARAM called with parameter set to
Explanation One of the VINES iookup functions was called with an illegal argument
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
302 System Error Messages VINES Error Messages
Error Message %VINES-2-EADTIMER RTP timer for was found disabled and was reset lOONESEC
Explanation An internal interface timer is not running This condition usually occurs after an interface reset
Recommended Action None The system automatically restarts the timet
Error Message %VINES-2-CACHEFAILEDCannot build cache entry bytes for on
Explanation The cache population routing for VINES fast switching determined that the
MAC header on packet is too large to fit into the cache
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message %VINES-2-CACHEUNSUPP Caching of not supported on
Explanation The cache population routing for VINES fast switching was called for an interface that does not support VINES fast switching
and it Recommended Action Copy the message exactly as it appears report your technical support representative
Error Message %VINES-2-CONSISTENCY Error
Explanation The VINES code ran into situation that should not happen For example an IPC port number needs to be allocated but all 65535 port numbers are currently in use
Recommended Action Copy the message exactly as it appears and report it your technical support representative
System Error Messages 303 VINES Error Messages
Error Message %VINES-2-CORRUPTENTRY Detected corrupted entry in the table
Explanation The VINES code detected that an internal table entry was corrupted
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
Error Message %VINES-2-DUPADDR Duplicate address detected on interface
Explanation The router detected that its VINES address is being used by another router
Recommended Action Identify the other router that is using this address by manual
inspection of the routers Issue the command vines routing recompute on both routers If
router does not support the recompute keyword then on that router you must disable
VINES write the configuration to memory reboot the routel and then reconfigure VINES
Error Message %VINES-2--ENCAPFAILED Encapsulation failed for via on
Explanation The cache population routing for VINES fast switching encountered an
encapsulation failure when building cache entry for neighbor
Recommended Action Examine your configuration for causes of the encapsulation
failure Look for missing map statements interfaces that have gone down and so on
Error Message %VINESEFNNOTFOUND service routine missing vector
Explanation There is an inconsistency in the static VINES data structures for handling
application-layer packets
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
304 System Error Messages VINES Error Messages
Error Message %VINES-2-INIT mit code or doesnt match defined constant iOONESEC
Explanation software or hardware error occurred
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %VINES-2-INVALIDPATH Bad in path for neighbor entry
Explanation While searching the neighbor table the code determined that pointer that should point to VINES path structure actually points to some other structure
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message %VINES-2-INVALIDROUTE Bad in route for server entry
Explanation While searching the routing table the code determined that pointer that should point to VINES route structure actually points to some other structure
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message %VINES-6-IPCNOROUTINE IPC port registered without an upcall
Explanation There is an inconsistency in the active VINES data structure for handling but the IPC DATA messages message was received for port that should have listenei listener routine cannot be found
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
System Error Messages 305 VINES Error Messages
Error Message %VINES2--NEIGHBOR vines_update called with null neighbor
Explanation An internal software error occurred
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
Error Message %VINE5-2-NOBUFFERS No buffers available for
Explanation There were no buffers available to send packet
Recommended Action Examine your system for memory or buffer leaks
Error Message %VINES-2-NCMEJY No memory available for
Explanation The requested operation could not be accomplished because of low memory condition
Recommended Action Reduce other system activity to ease memory demands If conditions warrant upgrade to larger memory configuration
Error Message %VINES2-NOVENCAP Encapsulation failed on no vencap routine
Explanation The VINES code tried to send packet on an interface that does not have
new encapsulation routine
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
306 System Error Messages VINES Error Messages
Error Message %VINES-2-REASSEMBLY SRTP reassembly code returned invalid result code lOONESEC
Explanation An internal software occuntd
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %VINES-6-RPCNOSERVICE IPC port registered without service
Explanation There is an inconsistency in the active VINES data structure for handling
Net RPC messages message was received for port that should have service description but that service description cannot be found
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message %VINES-6-RThNOTFOUND service routine not found while
Explanation There is an inconsistency in the active VINES service description data structures service handler routine cannot find the description of its own service
Recommended Action Copy the message exactly as it appears and report it your technical support representative
System Error Messages 307 VIP Error Messages
VUP Error Messages
Versatile Interface Processor error messages
Error Message %VIEP-3-BADMALUCMD Unsupported MALU command arg pascb
Explanation The Route Processor RP or the Route/Switch Processor RSP passed
down command that the software was not prepared to handle
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %VIP-3-ON0PASCB PASCB Null for command arg
Explanation The Route Processor RP or the Route/Switch Processor RSP passed
down command that the software was unprepared to handle
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %VIP-3-NODISPATC-I Dispatch vector Null cmd dintf
Explanation No command dispatch vector was found for the specified interface
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %VIP-2 NOICES msgnoicbs
Explanation No Switch Processor SP interrupt control block structure was associated
with the port adaptor or the interface
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
308 System Error Messages X25 Error Messages
Error Message %VIP-3UNDEFIDBTYPE Undefined idb type
Explanation This message is sent from the VIP kernel when it sees media type other
than Ethernet Token Ring or serial These are the media types supported by Cisco lOS
Release 11.2 on the VIP The message might be caused by having an older version of the
software running on device with new VIP port adapter
Recommended Action Check whether the version of the software being run supports the
VIP port adapter If an old software version does not appear to be the problem copy the technical error message exactly as it appears and report it to your support representative
X25 Error Messages
X.25 error messages
Error Message %X25-3-AJJDRESSBAD Interface x25 address subaddress is too long X25_COMPLAIN_LEVEL
Explanation This message occurs when subaddress is configured When this subaddress limit is combined with the interfaces 121 address the total address exceeds the of 15
characters
Recommended Action Reconfigure the subaddress so that this does not happen
System Error Messages 309 X25 Error Messages
Error Message %X25-3-BADCONTFIG Interface X.25 current configuration retained
Explanation The interfaces X.25 configuration is not valid the existing configuration
was not changed
Recommended Action Verify the following
The interfaces switched virtual circuit ranges do not overlap for nonzero values lic hic ltc htc bc hoc For more information refer to Configuring Virtual
Circuit Ranges in the Router Products configuration Guide
If an incomingonly range is defined check that it is numerically less than the twoway
range
If an outgoing-only range is defined cheek that it is numerically greater than the
two-way range
No virtual circuit highllow parameter is zero unless its partner
low/high parameter is also zero
The default window sizes are less than the interface modulo
Error Message %X25-4-BAJJMBIT Interface VC partial data packet has N-bit set
Explanation This message occurs when virtual circuit is set up using the default
maximum packet sizes but the DTE and DCE are not configured with the same default
values packet was received that had the M-bit set signifying that more data follows but
the packet did not catty the maximum number of bytes allowed Such partial data packets
must have the M-bit cleared The resulting loss of message boundary might cause
problems for the data recipient
Recommended Action Verify the default flow control parameters of the DTE and the
DCE If this error recurs copy the error message exactly as it appears and contact your
technical support representative for assistance
310 System Error Messages X25 Error Messages
Error Message %X25-4-BADUPCALL Interface Unexpected call from LLC2 DTE
%X25-4-DEBULCI LCI deleted at interrupt time
%X25-2-ILLP4 Interface Illegal state when P4
%X25-3-INTIMEQ Interface LCN already in timer queue new time
%X25-3-NOLCI Interface Delete id not found in table
%X25-3--NOTFINDBH Cant find bfe host address to delete
%X25-3-NOTFINDI Cant find address to delete
%X25-3-NOTFINDS Cant find address to delete
%X25-3-SPUED1 Spurious Dl timer wakeup on LCI
Explanation An internal software error occurred
Recommended Action If any of these messages recur copy the message exactly as it appears and contact your technical support representative for assistance
Error Message %X25-3-COMPERR Interface LCI low-level stac compression X2 5_COMPLAIN_LEVEL
Explanation Stacker compression algorithm internal error or shortage of buffer space was encountered during compression operation This should never happen
Recommended Action Copy the message exactly as it appears and report it your technical support representative
System Error Messages 311 X25 Error Messages
Error Message %X25-4-LARGEPKSIZE Interface packet sizes too large lower values will be negotiated
Explanation The interfaces default packet sizes or outgoing packet size facility values Link Access Balanced are too large to be carried by Procedure LAPB
Recommended Action The router will negotiate lower packet size values automatically
The LAPB Nl value should be increased For example for an X.25 maximum packet size
of 1024 modulo X.25 operation will add bytes of overhead and modulo LAPB
defined to operation will add bytes of overhead the two bytes of CRC are be included
This means that Nl must be at least 1031 bytes 8248
Error Message %X253-LCIBOGUS in x25_timer NULL lci-idb
Explanation An internal software error occurred
Recommended Action Copy the message exactly as it appears and report it your
tebhnical support representative
Error Message %X255-NOBUF Interface LCI
Explanation This is warning only the compressed packet was not lost However an
X.25 packet layer RNR wait was generated and packet-level transmission on the LCN will
not resume RR issued until decompression buffer becomes available
Recommended Action If this message occurs frequently you may need to modify the
buffer pool Copy the message exactly as it appears and report it your technical support
representative
312 System Error Messages X25 Error Messages
Error Message %X25--5-NOMENI Interface LCI NO memory for dictionary
Explanation The 14K P1W history dictionaries could not be allocated PBP compression is not enabled
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message %X254-PARTIALMAP Interface encapsulation call from partially mapped to
Explanation An incoming X.25 call specified protocol that was assigned to multiprotocol map the VC will not be able to cany the full set of protocols specified by the map
Recommended Action Modify the configuration of the router or the far host to match the encapsulation method used
Error Message %X25-5-PBPDBIT Interface LCI PEP Compression does not support X25 bit X25_COMPLAIN_LEVEL
Explanation Compression is not enabled because D-bit support is configured for the LCI
Recommended Action Reconfigure without D-bit support or do not attempt to run with compression
Error Message %X25-5-PBPHOLDQ Interface LCI X25 Hold queue needs to be at least default size X25SOMPLAIN_LEVEL
Explanation An attempt was made to configure the X.25 hold queue to less than the minimum value
Recommended Action Configure the X.25 hold queue to be 10 or more
System Error Messages 313 X25 Error Messages
Error Message %X25-5-PBPNoENJ Interface chars LCI End system not configed for X25 PEP X25_COMPLAIN_LEVEL
Explanation compression or decompression operation was attempted by router other
than an end router Only end routers can perform compression and decompression
Recommended Action Reconfigure the routers so that only the end routers in the
network perform compression and decompression
Error Message %x25-3-P\TCEAD Interface PVC
Explanation switched PVC cannot be connected The final text string in the
message represents the state of the PVC These text strings can also appear in show x25-vc output For more information refer to the show x25-vc documentation in the Router
Pmducts Command Reference publication
Recommended Action Validate the configuration of the PVCs at both ends of the
connection and reconfigure them if necessary
Error Message %X25-3--PVCDELETE LCI for PVC being deletedl
Explanation PVC was using an x25 map entry that was deleted or the interface
configuration changed to make the PVC number illegal this forces the deletion of the PVC
Recommended Action No action required Note that some attached equipment may
object to an inability to use the deleted PVC
314 System Error Messages X25 Error Messages
Error Message %X25-4-RANGEUNUSED Interface VC range unused set limits to zero
Explanation An outgoing-only or incoming-only virtual circuit range exactly overlaps the two-way virtual circuit range This was the former method for specifying that virtual circuit range was not used The current method is to set the range limits to zero
Recommended Action Use the privileged copy running-config startup-config This the command to write the configuration to memory will store modified zero range limits
Error Message %X253SIZEBAD Interface LCI Decompression size error
Explanation An internal software error occurred The PBP header has an uncompressed packet size field Each uncompressed packet size is checked against this field
Recommended Action Copy the message exactly as it appears and report it your technical support representative
Error Message %X253SYNCBAD Interface DCI Decompression sync error Expected got
Explanation An internal software error occurred The PIBP header has sync field The sync field bits is checked on each received packet
Recommended Action Copy the message exactly as it appears and report it your technical support representative
System Error Messages 315 X25 Error Messages
Error Message %X25-4-VCLOSTSYNC Interf ace VC ICP cormection
Explanation An X.25 circuit that is being tunneled over TCP connection between
routers was cleared ungracefully The last text string in the message can take one of
two forms If the text string is closed unexpectedly the router at the remote end of the
connection was rebooted or the connection failed If the text string is connection
corrupted it is likely that the connection was made to router running an older software
release
Recommended Action If the text string is closed unexpectedly reestablish the
connection after the remote router or intervening network is operational If the text string
is connection corrupted upgrade the router at the other end of the connection to more
recent software release
Error Message %X25-3-VERSIONBAD Interf ace LCI Compression Version mismatch Expected received
Explanation An internal software error occurred The PBP header has mismatched
version field The version is checked on each received packet
Recommended Action Copy the message exactly as it appears and report it your
technical support representative
Error Message %X25-3-XOTPROTCCOL XOT protocol error from
Explanation protocol error was detected over an X.25-overTCP XOT connection causing the connected YC to close flaw may exist in the remote hosts XOT implementation
Recommended Action If this error recurs copy the error message exactly as it appears
and contact your technical support representative for assistance
316 System Error Messages XNS Error Messages
XNS Error Messages
Xerox Network Systems error messages
Error Message %XNS-3-EAJJPATHS Invalid number of paths for
%XNS2-BADRCUTE Error route null table
Explanation An internal software error occurred
Recommended Action If either of these messages recur copy the message exactly as it
appears and contact your technical support representative for assistance
System Error Messages 317 XNS Error Messages
318 System Error Messages CP System Error Messages
conditions in The system can report error numerous facility codes related to the Channel
Interface Processor CIP As shown in the following example the format of the error messages for the CIP differs from the format of other system error messages
%CIP36-MSG %ADAPTER-6---DIAGBEGIN diagnostic starting
All CIP-related error messages begin with percent sign the facility code GIP and nurnbei in the preceding example that indicates the slot where the CIP is installed The message severity level follows the slot number along with the mnemonic MSG This format parallels the format for other system error messages but it indicates that the CIP generated an error message
The information that follows the initial is the CIP error message facility subcode severity level and mnemonic%ADAPTER-6-DIAGBEGIN in the preceding example
The CIP error messages are organized alphabetically into sections by subfacility beginning with CJP-ADAPTER Within each subfacility section messages appear alphabetically by mnemonic
Note VP and the slot number are not shown in the error message listing that follows
CIP System Error Messages 319 CIP-ADAPTER Error Messages
CHPOiADAPTER Error Messages
CIP error messages for the adapter task
Error Message %ADAPTER-6-BADREQUEST ad request code generated on port
Explanation request was sent to the function that handles general requests for the
specified port The request code was not in range recognized by that function
Recommended Action The CIP recovered by ignoring the request Copy the error
message exactly as it appears and report it to your technical support representative
Error Message %ADAPTER-6--BADSTATE Bad state port request code state flags
in invalid state it the Explanation The specified port was an while attempted to process
specified general request
Recommended Action The CIP recovered by forcing the port into well-known state
Copy the error message exactly as it appears and report it to your technical support
representative
Error Message %ADAPTER 6DIAGEEGIN diagnostic starting
Explanation user used the test thus command to request particular adapter diagnostic
to be run This message informs the user that the diagnostic routine started
Recommended Action Wait for the next message
320 System Error Messages CIP-ADAPTER Error Messages
Error Message %ATJAPTERO-DIACDATA Module Call Error ID
Explanation diagnostic routine detected failure in the ESCON Channel Adapter
ECA hardware Use the hexadecimal codes that appear in the message to locate the specific component that failed
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %ADAPTER--DIAGDATA2 Module Call Error ID
Explanation diagnostic routine detected failure in the ESCON Channel Adapter
ECA hardware Use the hexadecimal codes that appear in the message to locate the
specific component that failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %ADAPTER-O-DIAGFAIL Port failed the diagnostic
Explanation diagnostic routine failed The specified port will not be used
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %Z\DAPTER-6-JI diagnostic failed
Explanation diagnostic requested by the test thus command failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 321 CIP-ADAPTER Error Messages
Error Message %ADAPTER6-DIAGGOOD2 chars diagnostic ran successfully
Explanation diagnostic requested by the test chits command completed successfully
Recommended Action None
Error Message %ADAPTER6-DIAGRANGE Diagnostic number out of range O-
Explanation The diagnostic number requested by the test thus command is not valid
diagnostic number
Recommended Action Reenter the command with valid diagnostic number
Error Message %ADAPTER-6--DIAGSTOP Interface must be shutdown to run diagnostic
Explanation The test chits command was used to run diagnostic on an active interface
Recommended Action Use the shutdown command to stop the interface and then
reissue the diagnostic request
Error Message %ADAPTER-O-DIAGTERM Port The diagnostic failed to terminate
will Explanation diagnostic routine did not complete execution The specified port not be used
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
322 System Error Messages CIP-ADAPTER Error Messages
Error Message %NJAPTER-6--DIAGTERM2 diagnostic failed to terminate
Explanation diagnostic requested via the test ebus command did not terminate
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %ADAPTER-O-LOADFAIL Port microcode load failed
Explanation Each adapter has an onboard microprocessot This message indicates that the
operation to load the code for that microprocessor failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %ADAPTER-6-LOGDATA
Explanation An error occurred in the adapter The information displayed will help
personnel in software development to determine the nature of the error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %ADAPTER-6-LOGCUT Port logout data
Explanation This message is displayed at the start of the logout data It is then followed
whenever is by the message ADAPTER-6-LOGDATA Logout data occurs problem
detected on the port adapter or with an ESCON Channel Adapter ECA on the fiber
Recommended Action If this message appears continually on new installation it might
indicate that the fiber is not connected properly Verify that the connector is firmly seated
If loose fiber was not the cause of these messages copy the error message exactly as it technical appears and report it to your support representative
CIP System Error Messages 323 CIP-ADAPTER Error Messages
Error Message %AIJAPTER6--LOCSN4E to same as above
Explanation This message is used when logout information is displayed in order to avoid
printing duplicate data
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %ADAPTER-6-SCAN Port scan data
Explanation The data in this message is scan data for the adapter in the specified port
This data is usually produced as result of hardware error
Recommended Action Copy the error message exactly as it appears along with the scan
data and report it to your technical support representative
Error Message %ADAPTER-6-SCANDATA
Explanation The data in this message is related to hardware failure of an adaptei
Recommended Action Copy the error message exactly as it appears along with the scan
data and report it to your technical support representative
Error Message %ADAPTER-O-START_FAIL Diagnostics failed for port start request ignored
Explanation Before the adapter receives start command from the route processor set
of diagnostics is run If diagnostic test fails the adapter is started when the start command
is issued
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
324 System Error Messages CIP-BSQ Error Messages
Error Message %ADAPTER-6-WRAP Wrap plug detected in port Wrap loop started
Explanation wrap plug is installed in the specified port Wrap diagnostics will run until
the plug is removed if this is the only adapter or if both adapters have wrap plugs installed
Recommended Action Remove the wrap plug and connect the interface to channel
Error Message %ADAPTER-6---WPAPSTGP1 Wrap plug removed from port Wrap loop ended
Explanation The wrap plug was removed causing the wrap diagnostics to terminate
Recommended Action No action is required
Error Message %ADAPTER-6-WRAPSTCP2 Port active Port wrap loop ended
the other is Explanation The wrap diagnostics have been terminated because adapter active
Recommended Action Remove the wrap plug and connect the interface to channel if
you wish to use this adapter Otherwise no action is required
CIPBSQ Error Messages
CIP error messages for buffer status queue processing
Error Message %BSQ-O-SCB_CHAIN Read SOB chain is out of sequence
for read commands Explanation The sequence of buffer status queue entries received
for the reads This is fatal does not match the sequence of the storage control blocks used
internal logic error
it and it to Recommended Action Copy the error message exactly as appears report your
technical support representative
CIP System Error Messages 325 CIP-CBUS_ATTN Error Message
Error Message %BSQ-O-TOOM7\NY More than 16 buffers queued for one channel command
Explanation Either an attempt was made to transfer more data in single channel
command word than the CIP can handle or an internal error occurred This is fatal
internal logic errot
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIPCBUS_ATTN Error Message
CIP error message relating to the CBUS_ATTN routine the facility that receives
configuration requests and gathers statistics
Error Message %CBUSATn3BADADDR Bad memory address requested
Explanation The Route Processor RP requested that the CIP store configuration
command at an invalid memory address The CIP recovered by ignoring the request
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
326 System Error Messages CIP-CBUSWRITE Error Messages
CUPCBUSWRITE Error Messages
CIP for the is used error messages CBUSWRITE facility which by the enhanced online insertion and removal EOIR support on the CIP to track write operations to the memory
device and reissue them if ciscoBus problem occurs
Error Message %CBUS_WRITE3-BADTYPE Invalid write type
Explanation The type parameter in the write tracking table is invalid This is an internal
CIP logic error The CIP recovered by ignoring the entry
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CBUS_WRITE-3-INVALID Valid bit not set in 10 exception register hex
Explanation write error interrupt occurred but the hardware that keeps track of the
address of the error does not have valid address
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CBUS_WRITE-3-MISSIN0 Entry for address not found
Explanation write error was detected but no corresponding entry appeared in the table
that keeps track of these entries This is an internal CIP logic error The CIP recovered by
ignoring the write error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 327 CIP-CCA Error Messages
Error Message %CEUS_WRITE-3-STACK
Explanation This is debugging print of the CBUS write stack It is associated with the
CBUS_WRITE-3-MISSING error message
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CRUS_WRITE-3---UNExPECTED Unexpected 10 write error Address
Explanation write operation to an address other than memory device MEMD has timed out This is probably hardware problem The CIP failed and attempted to restart
The address displayed in the error message indicates which component might have the problem
Recommended Action If this problem persists copy the error message exactly as it
appears and report it to your technical support representative
CIPCCA Error Messages
CIP error messages for channel card adapter processing
Error Message %CCA3-ACR Accept coirmand response status received
Explanation The adapter notified the CIP that an accept command response was issued
The CIP does not request notification of accept command response messages Therefore
this message means the adapter generated an unexpected message
Recommended Action Normal processing will resume but it is useful for software
development personnel to know that this message occurred Copy the error niessage exactly
as it appears and report it to your technical support representative
328 System Error Messages CIP-CCA Error Messages
Error Message %CCAO-BADCCA Undefined CCA code received CCA
Explanation The adapter presented the CIP with message using an undefined code point This is fatal internal logic erroi
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CCA-O-BSQFULL Buffer status queue is full
Explanation The adapter notified the CIP that the buffer status queue was full The CIP
never provides enough buffers to the adapter to cause the buffer status queue to become full
This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CCA-3-BYPASS Select bypass switch may be in bypass position for port
Explanation Either you attempted to start the parallel channel adapter PCA with the
select bypass switch in the bypass position or the PCA priority is too low to receive
response from the channel The PCA cannot go online with the switch in the bypass
position
Recommended Action Move the select bypass switch on the PCA-Y cable from the
bypass position to the select position
CIP System Error Messages 329 CIP-CCA Error Messages
Error Message %CCA-3-CANCEL1 Invalid cancel code
Explanation The adapter notified the CIP that halt subcharrnel command was issued by
the host but provided the CTP with an undefined type of cancellation
Recommended Action The CIP has recovered but Cisco software development needs to
it and know about the problem Copy the error message exactly as appears report it to your
technical support representative
Error Message %CCA-3-CANCEL2 Cancel received for undefined path
Explanation The adapter notified the CIP that halt subehannel command was issued by
the host for an undefined path This is an internal logic error
Recommended Action The CIP has recovered but Cisco software development needs to
know about the problem Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CCA-3-CDMMAND_PATH Command connection received for undefined path
Explanation The adapter notified the CIP that start subehannel command was issued
by the host for an undefined path This is an internal logic error
Recommended Action The CIP software has recovered but Cisco software development
needs to know about the problem Copy the error message exactly as it appears and report
it to your technical support representative
330 System Error Messages CIP-CCA Error Messages
Error Message %CCA-3--CONN_RESULT Connection result for device expected
Explanation The adapter notified the ClIP that connection was established for device other than the one that the CIP had just requested This is an internal logic error
Recommended Action The CIP software has recovered but Cisco software development needs to know about the problem Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CCA--O-DEVERRi Undefined device error type
Explanation Normally when device error occurs the adapter specifies the type of error so that the correct recovery action can be performed The type specified is not defined This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CCA-O-DEV_ERR2 Device error but no active defined device
Explanation device error was generated and either it occurred while status was being presented but no device was active or it occurred for an undefined device This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CCA-O-IJEVERR3 Device error received for undefined path
is Explanation device error occurred but the path specified in the device error message not defined This is fatal internal logic error
and it to Recommended Action Copy the error message exactly as it appears report your technical support representative
CIP System Error Messages 331 CIP-CCA Error Messages
Error Message %OCA-3-END_STATUS Ending status interrupt received for CCW
Explanation The adapter reported an ending status interrupt for channel command word
that should not have caused the CIP to be notified This is an internal logic errot
Recommended Action The ClIP software has recovered but software development needs
be notified the it to of problem Copy the error message exactly as appears and report it to
your technical support representative
Error Message %CCA--3-LOGOUT Invalid logout command modifier
Explanation The adapter sent request to the CIP to perform logout but the command
modifier in the message was not valid value This is an internal logic errot
Recommended Action The ClIP software performed recovery but Cisco software
development needs to know about the problem Copy the error message exactly as it
appears and report it to your technical support representative
Error Message %CCA3-REQUEST_STATUS Request status received for imdefined path
Explanation The adapter requested the ClIP to present status for an undefined path This
is an internal logic error
Recommended Action The ClIP software performed recovery but Cisco software
development needs to know about the problem Copy the error message exactly as it
appears and report it to your technical support representative
Error Message %CCA-3-RESET_PATH Reset received for undefined path
Explanation The adapter requested that the CIP perform reset processing for an undefined
path This is an internal logic error
Recommended Action The ClIP software performed recovery but Cisco software
development needs to know about the problem Copy the error message exactly as it
appears and report it to your technical support representative
332 System Error Messages CIP-CCA Error Messages
Error Message %CCA-3-PLPl Invalid rip flags
Explanation The adapter requested that the CIP reset logical path but the flags on the reset request were not valid This is an internal logic error
Recommended Action The CIP software performed recovery but Cisco software development needs to know about the problem Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CCA-3RLP2 RLP received for undefined path
Explanation The adapter requested that the CIP reset an undefined logical path This is an internal logic error
Recommended Action The CIP software recovered but software development needs to be notified of the problem Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CCA-O-SCBNFDY Unexpected SCB not ready CCA
Explanation The CTP was notified that an 1/0 operation was attempted with storage control block that was marked as not ready The specified 110 operation should never have
not ready storage control block This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CCA-3-SELRESET1 Invalid selective reset code
Explanation The adapter requested that the CIP perform selective reset but the request code in the message was not valid value This is an internal logic error
Recommended Action The CIP software performed recovery but Cisco software development needs to know about the problem Copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 333 CIP-CCA Error Messages
Error Message %CCA-3-SEL_RESET2 Selective reset received or undefined path
Explanation The adapter has requested the CIP to perform selective reset on an
undefined logical path This is an internal logic error
Recommended Action The CIP software performed recovery but Cisco software
development needs to know about the prob1em Copy the error message exactly as it
appears and report it to your technical support representative
Error Message %CCA-3--STATUS NOTICE Undefined status notice request code
Explanation The adapter notified the CIP that status was accepted by the channel but the
request code in the status message was not valid code This is an internal logic error
Recommended Action The CIP software has recovered but software development needs
to be notified of the problem Copy the error message exactly as it appears and report it to
your technical support representative
Error Message %CCA-3-SYSRESET Invalid system reset code
Explanation The adapter requested that the UP perform system reset but the request
code in the message was not valid value This is an internal logic errot
Recommended Action The CIP software has recovered but software development needs
to be notified of the problem Copy the error message exactly as it appears and report it to
your technical support representative
Error Message %CCA-O-TOOMANY Too many buffers required for write operation
Explanation The mainframe wrote data to the CIP The number of buffers needed to hold
that data exceeded the total number of buffers allocated on the CIP for that purpose This is
fatal error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
334 System Error Messages CIP-CLAW Error Messages
Error Message %CCA-3---WRAPPLUG Wrap plug is installed on port dec
Explanation The wrap plug is installed on the parallel channel adapter PCA in the
specified port The PCA cannot be used unless connected to channel
Recommended Action Remove the wrap plug and connect the channel cables
Error Message %CCA-O-WRITE_FAIL Write of response CCA failed
Explanation The adapter requested that the CIP perform an operation When the ClIP tried
to respond to the request it was not able to write to the common communication area This
is fatal internal logic errol
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIPCLAW Error Messages
Workstations CIP error messages related to the Common Link Access for CLAW facility
Error Message %CLAW-O--BADAPPL Host Appl names do not match any configured names
Explanation An attempt was made to establish connection but the application names in the specified on the host do not match any of the application names specified router
configuration
Recommended Action Contct the host and/or router configuration
CIP System Error Messages 335 CIP-CLAW Error Messages
Error Message %CLAW-O-BADAPPL2 Configured names
Explanation An attempt was made to establish connection but the application names
specified on the host do not match the application names specified in the router
configuration
Recommended Action ColTect the host and/or router configuration
Error Message %CLAW6--BADCHAIN Too many buffers in an IF Datagram write chain
Explanation All data sent in an IP datagram must fit in one transfer list element This IP
datagram required more than one transfer list element
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CLAW-D-BADHAPPL Host appi names do not match Host is Control Unit is
Explanation An attempt was made to establish connection but the host application
names specified on the host do not match the host application names specified in the router
configuration
Recommended Action Correct the host and/or router configuration
Error Message %CLAW-O--BADIThIAME Host system names do not match \nHost is Control Unit is
Explanation During the system validate processing the host name configured in the
router did not match the host name configured on the host
Recommended Action Correct the host and/or router configuration
336 System Error Messages CIP-CLAW Error Messages
Error Message %CLAW-U-BADRSIZE Host read frame size of is less than Control Unit size of
Explanation The host is configured to receive frames that are smaller than the CIP is designed to send The CIP notified the host of the problem
Recommended Action Reconfigure the frame size on the host to be 4096 or larger
Error Message %CLAW-6-BADSVR System Validate Response had return code of
Explanation The host generated an invalid return code in the response to the system
validation request sent by the CIP
Recommended Action Check the return code and correct the configuration as
appropriate
Error Message %CLAW-O--BADVERSION Host CLAW version does not equal control unit version
is the Explanation The version specified in message from the host not the same as
version specified in the CIP
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CLAW-O-BADWAPPL Workstation appl names do not match.Host is Control Unit is
Explanation An attempt was made to establish connection but the workstation the application name specified on the host does not match workstation application name
specified in the router configuration
Recommended Action Correct the host and/or router configuration
CIP System Error Messages 337 CIP-CLAW Error Messages
Error Message %CLAW-O-BAIJWNAME Workstation system names do not match \nHost is Control Unit is
Explanation During system validate processing the work station name configured in the
router did not match the work station name configured on the host
Recommended Action Conect the host and/or router configuration
Error Message %CLAWO-BADWSIZE Host write frame size of is greater than Control Unit size of
Explanation The host is configured to write more data in single frame to the CIP than
the CIP is designed to receive The CIP notified the host of the problem
Recommended Action Reconfigure the frame size on the host to be 4096 or smaller
Error Message %CLAW-6-CONMAND Unrecognized CLAW command code xfer_elenent Ox
Explanation The host sent CLAW command with an invalid CLAW command code
The CTP ignored the request
Recommended Action Copy the error message exactly as it appears and report it to ypur
technical support representative
Error Message %CLAW-6-LONCREC Attempt to transmit too large record
Explanation The amount of data being read by the channel exceeded the size of the read channel command word CCW
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
338 System Error Messages CIP-CLAW Error Messages
Error Message %CLAW-6-NOCCNN Channel wrote data on link without valid connection Path devicet
Explanation packet was received from the host but the logical link specified with the data does not represent valid connection The packet was dropped
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CLAWO-NOLINKID Unable to allocate link id
Explanation An attempt was made to allocate link ID to assign to connection request but all link IDs were in use The CIP recovered by generating an invalid return code to the requester
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CLAW-6-NOTPRESENT Link being freed was not present
Explanation The host software attempted to disconnect link that was not established
The CIP ignored the request
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CLAW6NOTXBUF Unable to allocate txbuf
Explanation No available transmit buffers exist but the CLAW connection has not reached its transmit buffer limit The packet was dropped
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 339 CIP-CLAW Error Messages
Error Message %CLAW-6-RANGE Link being freed is out of range
Explanation The link ID in disconnect is not in the valid range for all CLAW links The
CIP recovered by ignoring this request
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CLAW6-TOCBIG byte IP datagrarn exceeds CLAW MTU for device
Explanation The router has sent an IP datagram to the CTP that is larger than the
maximum transmission unit MTU value set for the CIP The IP datagram has been dropped
Recommended Action The MTU value for the CLAW connection is set in the DEVICE
statement for the CLAW device in the host TCP/IP configuration file PROFILE.TCPIP
Check the configured IP MTU value on the CIP and in the host configuration file If correct
copy the error message exactly as it appears and report it to your technical support
representative
Error Message %CLAW6-TYPE Unrecognized type code in CLAW xfereiement Ox
Explanation The request type in transfer element is not valid value This is an internal
logic error The CIP recovered by ignoring the transfer element
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
340 System Error Messages CIP-CLAW Error Messages
Error Message %CLAW6-IJNEXPECTED Unexpected type code in CLAW xfer_element Ox
Explanation The request type in transfer element is valid but this type of element is not expected to occur at this time This is an internal logic error The CIP recovered by ignoring the transfer element
Explanation Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CLAW-6--VTRTCLAW CLAW device may not be created on virtual port adapter
Explanation An attempt was made to configure CLAW device on the virtual port adapter CLAW devices are permitted on real port adapters only The configuration request was ignored
device of Recommended Action Verify that you are configuring the CLAW on right type port adaptei
CIP System Error Messages 341 CIP-CONFIG Error Messages
CIPCONFIG Error Messages
ClIP error messages related to the configuration facility
Error Message %CONFIG-6-BADCONPIG Bad configuration type in update_tx_max
Explanation The router encountered an unrecognized configuration type when it
attempted to update the maximum number of transmit buffers to be used by device This
is an internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CONFIG-6BAD_DBTYPE Bad port type
Explanation The port type function returned an invalid port type This is an internal logic
error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CONFIC---BADDEVT Bad device type
Explanation The device type specified by the route processor in configuration request
is not valid device type This is an internal logic error The configuration request was
ignored
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
342 System Error Messages CIP-CON FIG Error Messages
Error Message %CCNEICO--BADSPEED Incorrect PCA speed passed to cbus attention exit routine
Explanation The router attempted to configure parallel channel adapter PCA with an invalid channel speed
Recommended Action The CIP software recovered by ignoring the request Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CONPIG-3--BADVCN Virtual circuit number too large
Explanation The virtual circuit number specified by the route processor on configuration request is too large This is an internal logic errot The configuration request was ignored
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CONFIG-3-IBADVCN2 Bad von port adapter
Explanation packet has been queued for the CIP with an invalid virtual circuit numbet
The CIP recovered by dropping the packet
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CONFIG-3-CLAWDEV CLAW device address must be even
Explanation The route processor attempted to configure an odd-numbered address for
CLAW device CLAW configuration requests must specify an even-numbered address This is an internal logic error The configuration request was ignored
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 343 CIP-CONFIG Error Messages
Error Message %CONFIG3-CONFIGINIT Invalid config registry identifier
Explanation During initialization each application that receives configuration commands
from the system registers the routines needed to process its configuration commands An
incorrect registration identifier was used This is fatal errot The CIP has been restarted
Recommended Action No action required
Error Message %CONFIG-3-DIFFDEVt Device type does not match device device type
Explanation The route processor attempted to reconfigure an existing device without first
removing the device This is an internal logic error The original configuration remains
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CONFIG-3--DUPDEV Duplicate device address
Explanation The route processor attempted to configure an existing device This is an
internal logic error The configuration request was ignored
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CCNFIG-3--DUPVCN Virtual circuit number already in use Path Device
Explanation The route processor attempted to configure device using virtual circuit
number that was already in use by another device This is an internal logic error The
configuration request was ignored
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
344 System Error Messages CIP-CONFIG Error Messages
Error Message %CONFIG-3-NOAFPLSPC Error allocating storage for application block
Explanation The CIP does not have sufficient storage to allocate an application block
The configuration request was ignored
Recommended Action Purchase the next larger storage size for the CIP or configure fewer devices
Error Message %CONFIG-3-NOCONEIG No configiiration routine registered for entry
Explanation Configuration command processing is dynamically set up when features are
added to an image The feature needed to process configuration command is not part of the current image
Recommended Action Either nm CIP microcode load that supports the configuration
command being issued or do not issue that configuration command
Error Message %CONFIG-3---NOCUI Control unit image does not exist for
Explanation The route processor attempted to unconfigure device but the control unit
image for the device could not be located This is an internal logic error The
unconfiguration request was ignored
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CONFIC-3--NODEV Device is not defined
Explanation The route processor attempted to unconfigure device but the device was
not defined This is an internal logic error The unconfigure request was ignored
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 345 CIP-CONFIG Error Messages
Error Message %CCNFIG-3-NODEVSPC Error allocating storage for device block
Explanation No storage was available for the device block The configuration request is
ignored
Recom mended Action Purchase the next larger storage size for the CIP or configure fewer devices
Error Message %CONFIG-3-NOFREEPATH No free paths only 64 may be specified
Explanation An attempt was made to configure more than 64 different paths Only 64
paths are supported The configuration request was ignored
Recommended Action Configure fewer paths
Error Message %CONFIG3-NOPATHSPC Error allocating storage for logical path table
Explanation No storage was available for the logical path table The configuration request
was ignored
Recommended Action Purchase the next larger storage size for the CTP or configure fewer devices
Error Message %CONFIG-3--NOSPAOE No space to bilild configuration confirmation
Explanation Whenever the system sends configuration command to the CIP it responds
with confirmation message Not enough memory was available on the CIP to allocate block to hold confirmation message
Recommended Action If you are not at the maximum CIP memory configuration you can install additional memory on the UP Otherwise configure fewer channel connections
346 System Error Messages CIP-CONFIG Error Messages
Error Message %CONFIG-3-NOVCN Virtual circuit number is not defined
Explanation The route processor attempted to unconfigure device but the virtual circuit number for the device is not defined This is an internal logic error The unconfiguration request was ignored
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CCNFIG-3-OFFLOADIJEV OFFLOAD device address must be even
Explanation The route processor attempted to configure an odd address for an OFFLOAD device OFFLOAD configuration requests must specify an even address This is an internal logic errot The configuration request was ignored
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CONFIG3-OFFLDEV OffiLoad device address must be even
Explanation The route processor attempted to configure an odd-numbered address for an offioad device Offload configuration requests must specify an even-numbered address
This is an internal logic enoi The configuration request was ignored
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CONFIG-3-STATEINIT Too many state change notification routines
Explanation During initialization each application that uses the virtual port adapter registers to receive notification when that adapter is shut or not shut The table to hold these registration requests is too small
Recommended Action This is fatal error The CIP has been restarted
CIP System Error Messages 347 CIP-CONFIG Error Messages
Error Message %CONFIG3-TOOMMIYDEV Too many devices defined Only 256 may be used
Explanation An attempt was made to define more than 256 devices Only 256 devices are
supported on an adapter The configuration request was ignored
Recommended Action Configure fewer devices
Error Message %CONFIG3--UNEXPCFG Configuration command code is not supported
Explanation Configuration command processing is dynamically set up when features are
added to an image The feature needed to process the configuration command is not part
of the current image
Recommended Action Either run CIP microcode load that supports the configuration
command being issued or do not issue that configuration command
Error Message %CONFIG-3-WORKLEFT Work pending on work queue when device terminated
Explanation Work was pending when the router finished processing an unconfigure
request This is an internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CONFIG-3--WRONGINT VCN not for port adapter
Explanation packet has been queued for the CIP with valid virtual circuit numbei but
the virtual circuit number is associated with the other port adapter The CIP recovered by
dropping the packet
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
348 System Error Messages CIP-CTA Error Messages
CIPCTA Error Messages
CIP error messages for the channel transport architecture device task/mapper
Error Message %CTA--BADCHAIN PA CTA Too many buffers in CSNA write chain
Explanation All data sent in CIP Systems Network Architecture CSNA write request
normally fits in one transfer list element This message required more than one
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CTA-O-ERRSTASH PA CTA buffer Ox not in stash pc Ox
Explanation An error has been detected in the processing of host-bound messages
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CTA-O-ERRSTATE1 PA CTA sequence error during subchannei setup pc
Explanation host write request was received while the setup state equalled pending open
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 349 CIP-CTA Error Messages
Error Message %CTA-O--ERRSTATE2 PA OTA sequence error during subchannel setup pc
Explanation host read request was received while the setup state equalled setup open
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CTA-O--ERRSTATE3 PA CTA sequence error during subchannel setup pc
Explanation host read request was received while the setup state equalled pending
complete
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CTAD--TERRSTATE4 PA CTA sequence error during suhohannel setup pc
host write received the Explanation request was while setup state equalled setup
complete
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CTA-6-FLUSH PA OTA Read data flushed
Explanation Due to an error on the channel some of the data that was intended for the channel was not sent to it Virtual Telecommunications Access Method VTAM will
receive an error indication and should retry the operation
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
350 System Error Messages CIP-CTA Error Messages
Error Message %CTA6-INII PA CIA Device initialized
Explanation CIP Systems Network Architecture CSNA device has been initialized
The elements of the device string CSNAx/yyyy/zz have the following meaning is the device number daughter card number yyyy is the path and zz is the
Recommended Action No action is required
Error Message %CTA-6-LONGREC PA CIA Attempt to transmit too large record
Explanation The amount of data being read by the channel exceeded the size of the read channel command word CCW
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CTA-O--MSGERRl FA CIA mismatch between channel block size and msg counts
Explanation An error was present in the host message as indicated by the description
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CTAO-MSCERR2 PA CIA hexL- msg size less than DLC hdr size
indicated the Explanation An error was present in the host message as by description
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 351 CIP-CTA Error Messages
Error Message %CTA-O--MSGERR3 PA CPA
Explanation The channel transport architecture CTA command code was not in the
valid range
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CTA-O--NONEM CIA attempt to acquire memory failed pc
Explanation call to create pool or get buffer failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CTAO--QUEUE_ERROR PA CTA attempt to iriit or alloc queue failed at Ox
Explanation queue initialization or allocation failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CTA-6-SHUTDOWN PA CIA Device shutdown
Explanation CIP Systems Network Architecture CSNA device was shut down The
elements of the device string CTAn/minnnn/yy have the following meaning is the
daughter card numbei mininin is the path and yy is the device number
Recommended Action No aOtion is required
352 System Error Messages CIP-CTA Error Messages
Error Message %CTA-O-SYSMGT_ERROR1 CTA detected error in sysmgt call invalid CSNA DEVICE length
%CTA-O--SYSMGT_ERROR2 CTA detected error in sysmgt call invalid LLC2 CONN length
%CTA-O-SYSMGT_ERROR3 CTA detected error in sysmgt call invalid CSNA type
Explanation An invalid parameter was received in system management call
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CTATESTTOQL-3-INVALIDCFGBLKLEN CTA Test-Tool configuration block length invalid
eta-test-tool with Explanation channel transport architecture CTA command an invalid configuration block length was received The command was ignored
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CTA_TEST_TOOL-3-INVALIDLEN CTA Test-Tool configured incorrectly for CTA command cmd hex
Explanation The offset and length of channel transport architecture CTA eta-test-tool command was out of range for CTA command buffer The CTA test tool cannot process the CTA command
Recommended Action Verify that the eta-test-tool command configured offset and length with values from the CTA formats and protocol document If you do not have configuration errol copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 353 CIP-CTA Error Messages
Error Message %OTJCTEST_TOOL-3-INVALIDMBUF CTA Test-Tool detected an invalid CTA command ituf cmd
channel architecture test tool cannot the Explanation The transport CTA identify format
of the CTA command memory buffet The CTA test tool cannot process the CTA command
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %CTA_TEST_TOOL-3--NOMEMORY CTA Test-Tool code could not allocate memory pc
allocate for the channel Explanation An attempt was made to memory transport available when the eta-test-tool architecture test-tool utility Not enough memory was
configuration command was processed by the CIR The eta-test-tool command will not be executed
Recommended Action Retry the eta-test-tool configuration command at later time or install more memory on the CIP card If neither action resolves the problem copy the error
message exactly as it appears and report it to your technical support representative
Error Message %CTA-O-JJNEXF_CTA_CP.u PA OTA received CTA command at
Explanation The received channel transport architecture CTA command code was not
in the valid range
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
354 System Error Messages CIP-CTA Error Messages
Error Message %CTA--O-UNEXP_EVENT PA CTA received unrecognized type code Ox at Ox
Explanation An transfer element type code outside the valid range was received
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CTZv-O-UNEXP_LSIJNJD PA CTA received LSI command at
Explanation The channel transport architecture CTA device task received Link
Services Interface LSI command code that was not in the valid range
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %CTAOJJNEXPLSL$TATUS CTA received status Ox in LSI cmd Ox
Explanation An invalid Link Services Interface LSI status code was received for the command
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 355 CIP-DEBUGGER Error Messages
CHPrDEBUGGER Error Messages
CIP error messages issued when nonrecoverable errors occur on the CIP
Error Message %DEBUGGER-O-CIPHWVINFO SNr HWRev EPROM VPLD
Explanation fatal internal CIP error occurred The message includes software version information
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DEEUCGER-O-CIPSWVINFO
Explanation fatal internal CIP error occurred The message includes software version information
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DEBUGGER-O---FATAL ERROR Fatal error code%02d
Explanation fatal internal CIP error occurred The CIP failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
356 System Error Messages CIP-DEBUGGER Error Messages
Error Message %DEBUGGER-O-LCORE_DATA
Explanation The message displays data from the low core area of the CIP
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %DEBUGCER-O-LCORESTART Dump of lowcore
Explanation The CIP has failed The low core area of the CIP will begin to dump
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %DEBUCGER-O--RESTART Restart due to breakpoint
Explanation The CIP finished dumping all debugging information and is attempting restart
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 357 CIP-DEBUGGER Error Messages
Error Message %DEBUGGERO-STACKJATA1
%DEEUCGER-O-STACK_DATA2
%IJEBUGGEFc-O-STACKDATA3
%DEBUGGEIR-O--STACK_DATA4
%DEBUGCER-O-STACK_DATA5
%DEBUGGERO--STACKDATAG
%DEBUGGERO-STACKDATA7
%DEBUGGER-O-STACK_DATA8
Explanation This message displays internal interrupt stack information
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DEBUGGERO-STACK START Stack addr
Explanation The CIP failed The internal interrupt stack will begin to dump
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DE3UGGER-Q-TRACEADDR Table Next First Last Full
Explanation This message displays the internal trace table header
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
358 System Error Messages CIP-DIAG Error Messages
Error Message %DEBUGGERO-TRACE_DATA
table Explanation The message displays single entry from the internal trace
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DEBUCGER--O-TRACE_START Dump of trace table
Explanation The CIP failed The internal trace table will begin to dump
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIPD1AG Error Messages
CIP error messages for diagnostic processing
Error Message %DIAG--6-BADCODE Invalid request code to run_diag
Explanation This is an internal logic errot request was made to run an ESCON Channel
Adapter ECA diagnostic but the number of the diagnostic to run was not valid The
request to run the diagnostic was ignored
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 359 CIP-DMA Error Messages
Error Message %DIAG-6-BADLOAD Firmware load error Unable to run_diag
Explanation This is an internal logic erroc request was made to run an ESCON Channel
Adapter ECA diagnostic but the firmware for the port adapter did not load properly The
request to run the diagnostic was ignored
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIPDMA Error Messages
Error messages for the function on the CIP that is responsible for transferring data between
the dynamic RAM DRAM on the CIP and memory device facility
Error Message %DMAO-BADFIFC FIFO failure detected during transfer
Explanation An error occurred in one of the hardware first-in first-out PIFOs used in the direct memory access DMA transfer operation The error was detected and caused packet to he dropped
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DMA-3-CBUSERR OBUS error no ACK neither NACK Ox
Explanation The CBUS controller started read or write operation and did not receive
response from the CBUS indicating the completion status The packet was dropped
Recommended Action Try reseating the CIP card If this problem persists copy the error
message exactly as it appears and report it to your technical support representative
360 System Error Messages CIP-OMA Error Messages
Error Message %DMA.3.cBusPARITy CEUS parity error Ox
Explanation parity ermr was detected on the CBUS during data transfec The packet has been dropped
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DMA--4-DATAPARITY DMA Data FPGA parity error Ox
Explanation parity error was detected during data transfer The packet has been dropped
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DMA0-INOOMPL DMA transfer incomplete on interrupt
Explanation The CIP was notified that the current direct memory access DMA transfer
had completed but the DMA status register indicated the transfer was still in progress The CIP restarted
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DMA-3-LOGICERR CBUS timeout 10 us Ox
Explanation The CBUS did not respond to the DMA controller within 10 microseconds l0s The packet was dropped
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 361 CIP-GE1IDATA Error Message
Error Message %DMA-O--NOXFER No transfer pending on DMA interrupt
Explanation direct memory access DMA interrupt occurred but no transfer was
pending This is either an internal logic error or hardware failure The CIP restarted
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %DMA-Q-REGISTERS
Explanation An error occurred during direct memory access DMA transfer The
hexadecimal numbers represent the DMA hardware controller registers at the end of the transfet
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIPGET_DATA Error Message
CIP error message related to the internal routine for allocating transfer elements
Error Message %GETDATAO-NOMEM0RY Can not allocate storage for xier elements
Explanation An attempt was made to allocate transfer element and no storage was
available This is fatal error The CIP restarted
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
362 System Error Messages CIP-INT Error Messages
C1P-INT Error Messages
CIP error messages for the interrupt handler interface
Error Message %INTO-ADDFAST Add Invalid fast lo code
Explanation request was made to add an interrupt handler to the fast 110 path with an
invalid interrupt type This is fatal internal logic errot
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %JNT-O-ADDFLIH Add Invalid interrupt code
Explanation request was made to add an interrupt handler with an invalid interrupt
number This is fatal internal logic errot
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %INT-O-ADDFULL Add Invalid full io code
ExpJanation request was made to add an 110 interrupt handler with an invalid interrupt
code This is fatal internal logic errol
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 363 CIP-INT Error Messages
Error Message %INT-O-ADDTRAP Add Invalid trap code
Explanation request was made to add system call handler with an invalid system call
number This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %INTO-REMOVEFAST Remove Invalid fast io code
Explanation request was made to remove an interrupt handler from the fast I/O path
with an invalid interrupt type This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %INT-O--ROVEFLIH Remove Invalid interrupt code
Explanation request was made to remove an interrupt handler with an invalid interrupt
numbet This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %INT-O--REMOVEFULL Remove Invalid full to code
Explanation request was made to remove an I/O interrupt handler with an invalid
interrupt code This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
364 System Error Messages CIP-IPC Error Messages
Error Message %INT-OREMOVETRAP Remove Invalid trap code
Explanation request was made to add system call handler with an invalid system call
uumbei This is fatal internal logic errot
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIPHPC Error Messages
CIP error messages related to the interprocess communication IPC subfacility
Error Message %IPC-2-CONSISTENCY Message failed consistency check
Explanation An internal IPC protocol error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %IPC-2-JJELETED Attempt to delete an IPC message Ox second time
Explanation An internal IPC protocol error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %IPC-2-LOCK Lock done on deleted element
Explanation An internal IPC protocol error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 365 CIP-IPC Error Messages
Error Message %IPC-2-NOBUFFER Could not fetch new message buffer
obtain Explanation The IPC protocol subsystem could not the message buffers it needed
Recommended Action The CIP card might require more memory Copy the error
message exactly as it appears and report it to your technical support representative
Error Message %IPC2-NODISPATCH Message from has no receive cieue or dispatch routine
Explanation An internal IIPC protocol error occurred
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %IPC-2--NOMEM No memory available for
Explanation The JPC protocol subsystem could not obtain the memory it needed
Recommended Action The CIP card may require more memory Copy the error message
exactly as it appears and report it to your technical support representative
Error Message
%IPC-2-NOLvvID Unable to obtain CEllS IPC buffers
Explanation The IPC protocol subsystem cannot obtain the buffers it needs
Recommended Action Ensure that at least one CIP interface is not shutdown Copy the
error message exactly as it appears and report it to your technical support representative
366 System Error Messages CIP-LOADER Error Messages
Error Message %IPC-2-UNLOOK Unlock done on already unlocked element
Explanation An internal IPC protocol error occurred
Recommended it it Action Copy the error message exactly as appears and report to your
technical support representative
CIPaLOADER Error Messages
CIP error messages related to the relocating loader facility
Error Message %LCADER-3--ABSERR Error not handled Symbol is absolute
Explanation The loader cannot handle variables of this type
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-3-ALOCER1 Error Allocating storage load fails
%LOADER-3-ALOCER2 Error Did not allocate storage loading of data failed
Explanation There is not enough storage to load this file
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative More storage will probably be needed You might use the
current storage more efficiently by running different combination of features
CIP System Error Messages 367 CIP-LOADER Error Messages
Error Message %LCADER-3--ATFERR Error atf array overflow
area-to-free is too small identifies the Explanation The ATF array The ATF array areas
to be freed when an attempted load operation fails
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LQADER-3-BAJJSHT Error Section header type not understood
Explanation The input file is not in the proper format
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-3-BADVEBS Invalid segment version
Explanation The segment version does not match the rest of the currently loaded software
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOAIDER3-BAYEXP Error Deleting external symbol from the exported table
Explanation The symbols should have been deleted from the table but were not This
error will probably cause problems during future file loads
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
368 System Error Messages CIP-LOADER Error Messages
Error Message %LOADER-3-BIGENID Error Input is not big endian
Explanation The input file is not the correct type for loading
Recommended Action Check the input file type If the file type is correct then copy the error message exactly as it appears and report it to your technical support representative
Error Message %LCADER-3-BINDERR Error Bind value in syrol table entry not understood
ExpJanation The loader cannot handle variables of this type
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message
%LOADER-3-COMERR Error tIre not handled must be .scommon
Explanation The loader cannot handle this type
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-3-CONMIX Error common variable matches name of non-common loaded variable
Explanation An error occurred in the input files
Recommended Action Copy the elTor message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 369 C1P-LOADER Error Messages
Error Message %LOADER-3-COMPER Error Compiled for incorrect target machine
Explanation The input file is not the correct type for loading
Recommended Action Check the input file type If the file type is correct then copy the
error message exactly as it appears and report it to your technical support representative
Error Message %LOADER3-DREADE Error Reading in program data
Explanation An error prevented the loader from reading section of the file
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-3---DTJPEXP Error Duplicate exported external symbol not allowed
Explanation The file being loaded attempted to export symbol that had already been
exported by previously loaded file
Recommended Action conflict exists between loadable files and/or the kernel Copy
it technical the error message exactly as it appears and report to your support
representative
Error Message %LOADER-3-EIDENT Error File header has unknown data in e_ident area
Explanation The input file is not in the correct format needed for loading
Recommended Action Check the input file format If the format is correct then copy the
it technical error message exactly as it appears and report to your support representative
370 System Error Messages CIP-LOADER Error Messages
Error Message %LOADER-3--ELF32 Error Input is not an ELF32 file
Explanation The input file is not in the correct fonnat needed for loading
Recommended Action Check the input file format If the format is colTect then copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOADER-3--ELFH Error Cannot read ELF header from input file
Explanation The loader could not read the module header information
Recommended Action Check the file If it is correct then copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOADER-3-ERRCNR Error Cannot relocate required symbol is not resolved
Explanation required symbol was missing
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOADER-3-ERR16H Error processing H116 L016 pair Low without High
Explanation The loader cannot handle relocation entries of this type
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 371 CIP-LOADER Error Messages
Error Message %LCADER3---FCLOSE Warning File close failed code
Explanation Loading is complete but the close operation failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER3--FILESIZE Unable to access image file
Explanation The CIP has failed to access the necessary image files
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER3--FOPEN Error Cannot open the input file
Explanation An error occurred when the system attempted to open file to be loaded
Recommended Action Confirm that the file exists Create it if possible If the problem
persists copy the error message exactly as it appears and report it to your technical support
representative
Error Message %LOADER-3--FOPENBZ Cannot open busy code will retry every secs for minute
Explanation required file is currently in use The system will attempt to open the file
every seconds for minute before failing the open attempt
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
372 System Error Messages CIP-LOADER Error Messages
Error Message %LOADER-3-FOPENER Error file open failure code
Explanation required file cannot be opened
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOADER-3-FREADE Error reading offset size
Explanation The loader could not read the input file The load failed
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOATJER-3-GPPROB Error Allocation of GP relative space problem left needed
has exhausted Explanation The space needed for the allocation of larger area been
Recommended Action Sufficient space should be allocated in advance Copy the error technical message exactly as it appears and report it to your support representative
Error Message %LOADER-3-GREADE Error reading in GP relative section data
Explanation An error prevented the loader from reading section of the file
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 373 CIP-LOADER Error Messages
Error Message %LOADER3-4IDRSIZ Error this size header entry cannot be handled
Explanation The file is not in the proper format The loader cannot handle it
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER3--HDRVER Error Input is not current version
Explanation The input file is not in the correct version of object file format
Recommended Action Check the file format version If the file version is correct then
copy the error message exactly as it appears and report it to your technical support
representative
Error Message %LQADER3-HREADE Error Cannot read headers from the file
Explanation An error occurred while the file headers were being read
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %L0ADER3-INSUFF Error insufficient space for subailocation left needed
Explanation Not enough space is available for the new allocation
allocated in Recommended Action Sufficient space should have been advance Copy the
error message exactly as it appears and report it to your technical support representative
374 System Error Messages CIP-LOADER Error Messages
Error Message %LOADER-O-INVALIDIOS 105 version incompatible with CIP must be at least
Explanation The version of Cisco lOS software is incompatible with this CIP microcode image
Recommended Action The Cisco 105 software must be updated to match the CIP version Copy the error message exactly as it appears and report it to your technicaT support representative
Error Message %LCADER-6-LOADING -- bytes
Explanation The CTP successfully loaded segment image
Recommended Action This is an informational message No action is required
Error Message %LOADER-O-LCADMAPDATA1 Ver Rev Segment
Explanation This message identifies the segment and the segments section information
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOADER-O-LOADMAPDATA2
Explanation This message provides information on the modules loaded into UP storage
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 375 CIP-LOADER Error Messages
Error Message %LCADER-O-L0ADMAP_DATA3
Explanation This message displays the compilation information for the segment listed in
the previous line
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-O-LOADMAP_EMPTY1 Loader initiallzation is not complete no segments loaded
Explanation The loader has not been initialized therefore no modules are loaded in CIP
storage
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-OLOADMAPEMPTY2 No segments have been loaded
Explanation The loader has not loaded any modules into CIP storage
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-O--LOADMAPjEADO Segment Load Map
Explanation This message precedes and introduces data listing the map of modules
loaded into CIP storage It also acts as header for the displayed data
Recommended Action Copy the error message and the data lines Contact your technical
support representative for assistance
376 System Error Messages CIP-LOADER Error Messages
Error Message %LOADER-O-LOAIJMAP_HEAD1 Start End Size Name
data the of modules Explanation This message precedes and introduces listing map loaded into CIP storage It also acts as header for the displayed data
Recommended Action Copy the error message and the data lines Contact your technical support representative for assistance
Error Message %LOAtJER-3-LOADRC Error Return code is
Explanation This message displays the error level on the load failure
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-3-NAXRSE Error too many Resident Symbol Tabies
Explanation The maximum number of resident symbol tables currently allowed is not
sufficient to handle this file
Recommended Action Increase the MAX_RSEJABS value and recompile the
loadreic file Copy the error message exactly as it appears and report it to your technical
support representative
Error Message %LOADER3-MAXSEC Error Total number of sections has exceeded pre-aliocated space for entries
Explanation The maximum number of sections currently allocated is not sufficient to
handle this file
Recommended Action Increase the MAX_SECTION_COUNT value and recompile the
ioadrel.c file Copy the error message exactly as it appears and report it to your technical
support representative
CIP System Error Messages 377 CIP-LOADER Error Messages
Error Message %LOADER-3-MAXSTRT Error Too many string tables
Explanation The maximum number of string tables culTently allowed is not sufficient to
handle this file
Recommended Action Increase the MAX_STR_TABS value and recompile the
loadreic file Copy the error message exactly as it appears and report it to your technical
support representative
Error Message %LOADER-3-4JAXSYMT Error Too many symbol tables
Explanation The maxinmm number of symbol tables currently allowed is not sufficient
to handle this file
Recommended Action Increase the MAXSYM_TABS value and recompile the
loadrel.c file Copy the error message exactly as it appears and report it to your technical
support representative
Error Message %LOADER-3--NOBITSO Error NOBITS but size is not not understood
Explanation Either the loader cannot process the input file or the file is not in the proper format
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-3-NODSO Error section contains dynamic shared objects
Explanation The input file cannot have dynamic shared objects
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
378 System Error Messages CIP-LOADER Error Messages
Error Message %LOADER3-NOELF Error Input is not an ELF file
Explanation The input file is not in the correct format
Recommended Action Check the input file format If the format is correct then copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOADER3-N0ERES Error Could not resolve external syrol
Explanation reference from the file being loaded to an external symbol cannot be resolved
Recommended Action Define all prerequisite external symbols before loading the file If
it and it to technical problems persist copy the error message exactly as appears report your
support representative
Error Message %LQADER-3-NoPREFIX Unable to detennine mcrocode image name
Explanation The CIP is unable to compose the microcode image name
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LCADER-3-NOPRG Error No code to handle program headers
Explanation The input file is not in the correct format
Recommended Action Check the input file format If the format is correct then copy the
error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 379 CIP-LOADER Error Messages
Error Message %LOADER3--NQSECH Error No section headers to process
Explanation The input file is not in the proper format
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER3-NOSQ Error section contains symbols conflicting with shared objects
Explanation The input file cannot have shared objects
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-3---NOTRE Error File is neither relocatable nor executable
Explanation The input file is not the correct type for loading
Recommended Action Check the input file type If the file type is correct then copy the
it technical error message exactly as it appears and report to your support representative
Error Message %LOADER-3-NOVERS No entry for \loader_segmentversion\
Explanation The loader requires that file to be loaded have an entry
loaderseginenLyersion containing specific structure
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
380 System Error Messages CIP-LOADER Error Messages
Error Message %LOADER-3-READERR Error file read failure code
Explanation An error occurred while the file was being read
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LO/DER-3--RELFLG Error Cannot handle the flags in the relocation entry
Explanation The loader cannot handle relocation entries of this type
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOADER-3-RELREAD Error Cannot read relocation entries
Explanation The loader could not read part of the file
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOADER3-RELTYP Error relocation type not recognized
Explanation The loader cannot handle this type of relocation
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOADER-3-RELTYP2 Error relocation type RJ4IPS_ not handled
Explanation The loader cannot handle this type of relocation
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 381 CIP-LOADER Error Messages
Error Message %LOADER3-RESERR external symbols cannot be resolved
files there Explanation Either the prerequisite are not loaded or are incorrect references
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-3-SECERR Error Cannot handle section
Explanation The loader cannot process this type of section of the code
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER3-SEEKER Error file seek failure code
Explanation An error occurred positioning within the file
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER3-SHFLAGE Error no storage allocated sh_f lags did not indicate how
Explanation The loader cannot handle this file
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
382 System Error Messages CIP-LOADER Error Messages
Error Message %LOADER-3-SHNHIPE Error not handled End appl specific range of indices
%LOADER-3--SHNHIR Error not handled End reserved range of indices
Explanation The loader cannot handle variables of this type
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOADER-3-SIZERR1 Error common variable has size incompatible with loaded variable
Explanation The loader cannot allocate larger variable to an already loaded smaller variable
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message
%LOADER-3-SORBER Error type not handled must be .sdata or .sbss
Explanation The loader cannot handle this type
Recommended Action Copy the error message exactly as it appears and report itto your technical support representative
Error Message %LOADER-3--SREADE Error Cannot read in symbol string
%LOADER3SEEADS Error Cannot read in symbol table
Explanation The loader could not read needed section of the file
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 383 CIP-LOADER Error Messages
Error Message %LOADER3-STOTHER Error Problem symbol table entry is using field ST_OTHER
Explanation The loader cannot handle this file
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-3--STREXE Error Strings exceed string table area allocated
Explanation The preallocated area is not large enough
Recommended Action The loader must be recompiled with more area Copy the error
message exactly as it appears and report it to your technical support representative
Error Message %LOADER-3--SUNDERR Error not handled Small undefined symbol
Explanation The loader cannot handle variables of this type
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %LOADER-3-5YNEXE Error Symbols exceed symbol table area allocated
Explanation The preallocated area is not large enough for loading
Recommended Action The loader must be recompiled with more area Copy the error
message exactly as it appears and report it to your technical support representative
384 System Error Messages CIP-LOADER Error Messages
Error Message %LOADER-3--SYRERR
Explanation An error occurred in the input file
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LCADER-3--TSHSIZ Error total sections headers too large for preallocated area
Explanation The preallocated area is not large enough for loading
Recommended Action The loader must be recompiled with more area Copy the error message exactly as it appears and report it to your technical support representative
Error Message %LOADER-3-TYPERR Error Type value in symbol table entry not understood
%LOADER-3--USRERR Error not handled Undefined section reference
%LOADER3-VARHIP Error Symbol is HIPROC variable not handled
%LOADER-3-VARLOP Error Symbol is LOPROC variable not handled
Explanation The loader cannot handle variables of this type
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 385 CIP-LOVE Error Message
CIPLOVE Error Message
CIP error message related to the mechanism that sends statistics from the CIP to the router
Error Message %LOVE-3-LCVELETTER Error in love letter processing
made transfer statistics the Route Processor Explanation An attempt was to to RP The direct memory access DMA routines returned the wrong transfer request The CIP recovered
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIPMBUF Error Messages
Memory buffer error messages
Error Message %MEUF-O-MFREEx2 mfree irthuf already free ed from pc ra pc ra
Explanation request was made to free memory buffer that was already free
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %PUF-O-PANIC panic in
Explanation An unexpected internal error occurred in the TCP/IP stack
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
386 System Error Messages CIP-MEMD Error Messages
CHPMEMD Error Messages
the device CIP error message related to memory facility
Error Message %MEND3-BADIPC IPC message received with no IPC handler
Explanation An interprocess communication IPC message was queued to the CIP but
no handler was defined to process it The CIP dropped the IPC message
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %NEMD3-BADPTR Bad pointer in M1KMD Code ICB Header Data
Explanation While processing buffer queue in the memory device facility the system
found pointer with an invalid value The CIP dropped the packet
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %MEMD3BADVCN Bad vcn port adapter
Explanation packet was queued to the CIP but the virtual circuit associated with the
packet is not valid The CIP dropped the packet
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 387 CIP-MSG8O2 Error Messages
Error Message %MEMD-3-VCNDERECISTER Invalid VCN specified
Explanation An attempt to deregister routine to handle data for the virtual circuit
identified in the message was ignored because the virtual circuit number was out of range
Recommended Action Try restarting the CIP If problems persist copy the error message
exactly as it appears and report it to your technical support representative
Error Message %MEMID-3-VCNREGISTER Invalid VON specified
Explanation The virtual circuit number identified in the message was out of range
preventing routine to handle that virtual circuit number from being registered No
messages for the given virtual circuit will be accepted Any messages that were sent to the
CIP for transmission on that invalid virtual circuit will generate additional error messages
Recommended Action Try restarting the CIP If problems persist report the error
message to your technical support representative
CPMSG8O2 Error Messages
Link Control CIP 802 error messages related to the IEEE 802.2cx Logical LLC protocol stack
Error Message %MSGBO2-3 -ADAPTER_LIMIT_EXCEEDED Configuration for adapter rejected
Explanation An attempt was made to configure more than 18 CIP Systems Network
Architecture CSNA adapters maximum of 18 CSNA adapters are allowed per CIP
Recommended Action Reduce the number of CSNA adapters configured to comply with
the 18 CSNA adapter limit
388 System Error Messages CIP-MSG8O2 Error Messages
Error Message %MSGSO2-6-ADAPTER_OPEM Adapter now open
Explanation This informational message is sent after the specified adapter opens
Recommended Action No action required
Error Message %MS0802-6-ADAPTERREt4 Adapter now removed
Explanation This informational message is sent after the specified adapter is removed
Recommended Action .No action required
Error Message %MS0802-6-ADAPTERUPD Adapter LLC parm now altered
Explanation This informational message is sent after changes have been completed to the
Logical Link Control LLC parameters for each specified adaptet
Recommended Action No action required
Error Message %MSG802-6--CTASET_FAIL set cta max_coma failed bytes free max corn remain at
Explanation In its cuntnt configuration the channel transport architecture CTA mapper cannot accept the maximum number of connections because it is low on resources such as of connections will fail memory An attempt to reduce the maximum number
Recommended Action CIP Systems Network Architecture CSNA should be run on CIP card with at least 32 MB of memory For all others refer to the CIP CSNA configuration guide to determine the memory requirements for the maximum number of connections configured Check the router configuration in the virtual interface of the CIP x/2 for the MAX_LLC_CONNECTIQNS parameter Determine whether the device is
it and it to overconfigured If it is not copy the error message exactly as appears report your technical support representative
CEP System Error Messages 389 CIP-MSG8O2 Error Messages
Error Message %M5G802-6-FRPNESZ_EXCEEDED frame exceeded max size bytes
device buffer frame size of Explanation The memory supports maximum 4472 bytes The CIP Systems Network Architecture CSNA detected frame that was larger than this maximum size The frame was discarded The system may be misconfigured
Recommended Action Verify that MAX_FRAME_LENGTH is configured If this does
not appear to be the problem then copy the error message exactly as it appears and report
it to your technical support representative
Error Message %MSG8O2-3--HARD_ERROR
Explanation The protocol stack encountered error conditions that prevent it from
continuing normal operations
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %MSG802-3--INVALID_CFGCND invalid config cmd detected cmd
Explanation The Logical Link Control LLC task detected an invalid configuration command The command was not executed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %MSGBO2-6-INVAILID ID invalid id type
Explanation The Logical Link Control LLC received an invalid ID type The LLC discarded the request
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
390 System Error Messages CIP-MSG8O2 Error Messages
Error Message %MSG8O23-JNVALID_MSICMD invalid msi cmd detected crnd
Explanation The Logical Link Control LLC task detected an invalid media access control MAC service interface command The request was canceled
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %M5G802-6-INVALID_PRIMITIVE invalid primitive code
Explanation The Logical Link Control LLC received invalid service primitives The
module and routine that received the primitives along with the service primitive codes are
displayed
Recommended Action The CIP Systems Network Architecture CSNA should continue
to operate If problems persist copy the error message exactly as it appears and report it to
your technical support representative
Error Message %MSG8O2-3INVALID_VCNl LAN not configured for vcn adapter lan rari cfg cmd rejected
Explanation The configuration command could not be processed because of an invalid virtual circuit number VCN The command was not executed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %MSG8O23INVALID_VCN2 LAN has configured for vcn adapter lan ran cfg cmd rejected
invalid Explanation The configuration command could not be processed because of an virtual circuit number VCN The command was not executed
and it Recommended Action Copy the error message exactly as it appears report to your
technical support representative
C1P System Error Messages 391 CIP-MSG8O2 Error Messages
Error Message %MSGSO26-LLCJJUP_CCB LLC Station Address Rt4AC LSAP RSAP
for station Explanation An open station request was received address that was already open
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %MSG8O2-6-LLC_DUPSAP TIC Duplicat SAP on interface SAP
been than Explanation The service access point SAP has opened by more one external communication adaptor XCA major node
Recommended Action Check the XCA node definitions
Error Message %MSC802-6--LLC_SHUT LLC shutdown completed
Explanation The shutdown of the Logical Link Control LLC is complete Both the LLC memory device READ/WRITE task and the TIMER task have been shut down
Recommended Action No action is required
Error Message %MSGSO2-6--LLC_START Starting LLC2 with session capacity of
Explanation Logical Link Control LLC subsystem session has begun
Recommended Action No action is required
392 System Error Messages CIP-MSG8O2 Error Messages
Error Message %MSGBO2-6-LLC Unexpected acknowledgement transmit not complete pcep
Explanation frame has been acknowledged before its transmission was completed
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %MSGSO2-6-MAX_FAILED change max conn tailed bytes free max conn remain at
Explanation The CIP is not able to support the maximum number of connections set in its current configuration The CIP may be low on resources such as connections and memory An attempt to reduce the maximum number of connections will fail
Recommended Action Check the ronter configuration in the virtual interface of the CIP x12 for the MAX-LLC-CONNECTIONS parameter Determine whether the device is over configured If it is not copy the error message exactly as it appears and report it to your technical support representative
Error Message %MSG8U2-6-M1X_FAILEt2 cipmsg pool empty max corn remain at
Explanation In its current configuration the CIP cannot accept the maximum number of connections because it cannot allocate message buffer from the CTP message pool
Recommended Action Retry the max_tic command If the error persists copy the error technical message exactly as it appears and report it to your support representative
CIP System Error Messages 393 CIP-MSG8O2 Error Messages
Error Message %MS0802-6-MA J3LC_EXCEEDED 1ThX.jJLC_SESSIONS exceeded sessions rejected
Explanation The maximum number of concurrent Logical Link Control LLC
connections has been exceeded
Recommended Action Increase the MAX_LLCSESSIONS parameter on the CTP
virtual interface
Error Message %MSG802 -3 -ODD NEMID Odd boundary memd buffer memd_addr
Explanation The memory device should never be in the odd boundary run-time error might have occurred
Recom mended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %MSO8 02-3 -QUEUE_OPEN
Explanation The Logical Link Control LLC task detected queue open failure The
resource is unavailable for the request
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %MS0802-3 -RESOURCE_DEPLETED
Explanation The protocol stack encountered error conditions that prevent it from
continuing normal operations
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
394 System Error Messages CIP-MSG8O2 Error Messages
Error Message %MSG8026-SHRINK_CoNN reducing maxconn doesnt take effect until the virtual interface is restarted max corn remain at
Explanation An attempt was made to reduce the MAXCONN parameter Reducing the
MAX_CONN parameter is not allowed in this release
Recommended Action No action is required
Error Message %MSG802-6-SHUT_IN_FROG shutdown in progress command rejected
Explanation The Logical Link Control LLC is in shutdown cleanup state In this state the LLC rejects all configuration commands
Recommended Action Retry the command when the LLC is in operational state
Error Message %MSGBO2-6-STARTSO2 FAILED unable to start 802 for connections Memory Avail bytes
Explanation The CIP is not able to bring up the channel transport architecture 802 task The CIP is low on resources such as connections and memory
Recommended Action Check the router configuration in the virtual interface of the CIP
x/2 for the MAX_LLQCONNECTIONS parameter Determine whether the device is
overconfigured If it is not copy the error message exactly as it appears and report it to your
technical support representative
Error Message %MSG8023-UNKNOWN EVENT detect unknown event event
Explanation The Logical Link Control LLC task detected an unknown event
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 395 CIP-MSG8O2 Error Messages
Error Message %MSG8 02-3 -UNSUPPORTED
Explanation The Logical Link Control LLC task detected request for an unsupported
function The request was canceled
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
396 System Error Messages CIP-NEVADA Error Messages
CPNEVADA Error Messages
Error messages related to the CIP interrupt controller
Error Message %NEVADA-O-BADADD Add Invalid nevada interrupt code
Explanation An attempt was made to specify an interrupt handler for an invalid interrupt
type on the NEVADA interrupt control chip This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %NEVADA-O-BADDISABLE Disable Invalid nevada interrupt code
the Explanation An attempt was made to disable an invalid interrupt type on NEVADA
interrupt control chip This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %NEVADA-O-BADFINABLE Enable Invalid nevada interrupt code
invalid the Explanation An attempt was made to enable an interrupt type on NEVADA
interrupt control chip This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 397 CIP-NEVADA Error Messages
Error Message %NEVADA-O-BADENABLE2 Enable No interrupt routine for code
Explanation An attempt was made to enable an interrupt routine on the NEVADA
interrupt control chip but no interrupt routine was specified This is fatal internal logic
error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %NEVADAO-EADINT Interrupt received with no interrupt routine defined
Explanation An interrupt was received for code with an undefined interrupt handler
This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %NEVAIDA- -BAIDREMOVE Remove Invalid nevada interrupt code
Explanation An attempt was made to remove an interrupt handler for an invalid interrupt
type on the NEVADA interrupt control chip This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
398 System Error Messages CIP-OFFL Error Messages
CUPOFFL Error Messages
CIP error messages related to the offload protocol
Error Message %OFFL-6-COMMAND Unrecognized Of load command code xfer_element Ox
Explanation The host sent an offload command with an invalid offload command code
The CTP ignored the request
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %OFFL-3--REX4W
Explanation This message contains hex dump of data associated with the immediately preceding error message
Recommended Action Copy the error message and the whole hex dump and contact
your technical support representative
Error Message %OFFL-3--HEX16B
associated with the Explanation This message contains hex dump of data immediately preceding error message
Recommended Action Copy the error message and the whole hex dump and contact
your technical support representative
CIP System Error Messages 399 CIP-OFFL Error Messages
Error Message %OFFL-3--ILLALIJ Illegal data alignment Ox bytes Ox xfer_element Ox
Explanation An internal logic error occurred block of offload protocol parameters
crossed buffer boundary The CIP ignored the request
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %OFFL-3--ILLALH Illegal hdr alignment detected Address Ox bytes Ox xferelement Ox
Explanation An internal logic error occurred An offload message header crossed buffer
boundary The CIP ignored the request
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %OFFL-3--ILLEN Illegal byte count in off load data specified available xter_element Ox
Explanation An internal logic error occutTed The buffer length field in the offload The CIP the offload message header does not equal the size of the data buffer assumes message header contains no data
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %OFFIrO-JLLFREE1 SCE chain does not end with read hdr
Explanation An internal logic error occurred An attempt was made to free sequence of
buffers The attempt failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
400 System Error Messages CIP-OFFL Error Messages
Error Message %OFFL-O--ILLFPEE2 SCE ends with read hdr with the MTC bit set
Explanation An internal logic error occurred An attempt was made to free sequence of buffers The attempt failed
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %OFFL-O-ILLINTE Illegal number of of fload interfaces specified expected
Explanation The offload initialization code found an internal error
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %OFFL-3-ILLRST Received restart with intf is max xfer_element Ox
Explanation The host sent an offload restart request with too many defined interfaces The
CIP ignored the request
Recommended Action Check your host configuration for this offload device Copy the error message exactly as it appears and report it to your technical support representative
Error Message %OFFL-6-LONGREC Attempt to transmit too large record
Explanation The amount of data read by the channel exceeded the size of the read channel command word CCW
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 401 CIP-OFFL Error Messages
Error Message %OFFL3-MISRST Received restart with unknown
Explanation The host sent an offload restart request with an unknown IP address for the
application programming interface API link
Recommended Action The CIP ignored the mismatch Correct your host configuration
for this offload device
Error Message %OFFL-6MSGLEFT Type xfer_element in work oeue after shutdown
Explanation An internal logic error occuned The offload application received message after shutdown The message was ignored
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %OFFLO--NOMBUF Out of inbufs for handling socket operations
Explanation An internal logic error occurred Not enough memory buffers were allocated
to handle the current offload socket operation
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %OFFL-3-NOMEM Not enough memory to start off load tasks
Explanation Not enough free memory is available to start the TCP/IP offload tasks The
configuration request was ignored
Recommended Action Install more memory for the CIP or configure fewer devices
402 System Error Messages CIP-OFFL Error Messages
Error Message %OFFLO-NOPENL Trying to free buffer when no send is pending Operation
Explanation request to free send buffer was made even though no send is pending
This is an internal logic erron
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %OFFL-6-NOTXBUF Unable to allocate txbuf
Explanation No transmit buffers are available for sending RESTART response
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %OFFL-3-PENDREQ Pending request deleted due to new request
Explanation An internal logic error occurred The offload application had to save socket
for later of the The first request execution while another request same type was pending request was dropped
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %OFFL-3-REJSOCK Not enough memory to handle new socket sockets open
Explanation Not enough free memory is available to open another socket The socket
failed request
Recommended Action Install more memory for the CIP configure fewer devices or
limitthe number of sessions through this offload device
CIP System Error Messages 403 CIP-OFFL Error Messages
Error Message %OFFL-3-REQFORN Socket request uses invalid parameters Offset
Explanation The host sent socket request with an invalid parametet The CIP sent an
error message in response to this request
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %OFFLr-3-REQLEN Socket request has wrong length
Explanation The host sent socket request with an incorrect length The CIP sent an error
message in response to this request
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %OFFL3--REQTYPE Unknown socket request code
Explanation The host sent socket request with an unknown type
Recommended Action The CIP ignored the request Copy the error message exactly as
it appears and report it to your technical support representative
Error Message %OFFL6-SOCREQ Unrecognized socket request code
Explanation The host sent socket request with an invalid code
Recommended Action The CIP ignored the request Copy the error message exactly as
it appears and report it to your technical support representative
404 System Error Messages CIP-OFFL Error Messages
Error Message %OFFL6-UNEXP Unexpected Of fload command code
Explanation An internal logic error occurred The request type in the offload message was valid but unexpected The CIP ignored the request
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %OFFL-6-VIRTOFFL Of load device may not be created on virtual port adapter
Explanation An attempt was made to configure an offload device oil the virtual port adapter Offload devices are permitted on physical port adapters only
Recommended Action The configuration request was ignored No action is required
Error Message %OFFL-6-WRCHAIN Received too long message xfer_element Ox chains to Ox
Explanation The offload application received message that consisted of more than one transfer element xfer_element This is not currently supported
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %OFFL-O-WRONGFREE Trying to free athuf out of sequence
Explanation An internal logic error occurred An unexpected address was specified in request to free buffer
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 405 C1P-SCB Error Message
Error Message %OFFL-3-WRONGLINK Trying to send robuf on CLAW control link
Explanation An internal logic error occurred An attempt was detected to send packet in memory buffer on Common Link Access for Workstations CLAW link The packet
was ignored
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIPSCB Error Message
controt block CIP error message related to the storage
Error Message %SCB6-BADSCB Request to free SCB ignored
Explanation An attempt was made to free storage control block SCB This is an
internal logic error The request was ignored
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIPSCHED Error Messages
which Error messages related to the scheduler the facility responsible for determining
process to run at given time on the ClIP
Error Message %SCI-iED-O-BADPRIORITY Task priority of dec is not allowed
Explanation request was made to create process butthe priority for the process was
not valid The process was not created
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
406 System Error Messages CIP-SCHED Error Messages
Error Message %SCHEDOINVLOCKl Invalied lock word of used in lock request
Explanation An attempt was made to request lock but the lock word contained invalid data This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SCHED-O-INVLOCK2 Invalied lock word of used in unlock request
Explanation An attempt was made to unlock lock but the data in the lock word was not valid This is fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SCHEDO--NMLDATA tcb_addr Oxhexj current_tcb Ox lock_value
Explanation This message contains data that relates to the SCHED-O-NOTMYLOCK message
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
Error Message %SCHED-D-NOLOCK Attempt was made to unlock resource that wasnt locked
Explanation An attempt was made to unlock lock that was not held This is fatal internal logic errot
Recommended Action Copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 407 CIP-SCHED Error Messages
Error Message %SCHEft-O-NCPROCID No process Id available for task creation
Explanation An attempt was made to create more tasks than the CIP is designed to allow
The task was not created
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SCIIEJ-Q-NOSTACK Could not allocate bytes for stack from SRAM
Explanation An attempt was made to create process but not enough storage was
available to contain the stack for the process The process was not created
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SCHEIJO-NOTCB Could not allocate bytes for tcb from SRAM
Explanation An attempt was made to create process but not enough storage was
available to contain the control block for the process The process was not created
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SCHED-O--NOTMYLCCK Attempt was made to unlock another tasks resource
Explanation An attempt was made to unlock lock that was set by another task This is
fatal internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
408 System Error Messages CIP-SLC Error Messages
Error Message %SCHED-ONOTPROCES Attempt was made to lock while not at process level
Explanation An attempt was made to lock while not at process level This is fatal
internal logic error
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CPPSLC Error Messages
CIP error messages related to the serial link controller
Error Message %SLC3-PCANMIRESET Reset of Port NMI failed
Parallel Channel Explanation After nonmaskable interrupt from Adapter PCA
interface was serviced an attempt to reset the interrupt failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SLC-3--SCANEP1 Scan of PP ring failed
Explanation An attempt to scan the first set of internal latches on the Enterprise System
Connection ESCON processor failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIP System Error Messages 409 CIP-SLC Error Messages
Error Message %SLC-3-SCANEP2 Scan of EP ring failed
Explanation An attempt to scan the second set of internal latches on the Enterprise
System Connection ESCONprocessor failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SLC-3-SCANSLC Scan of SLC ring failed
Explanation An attempt to scan the internal latches of the serial link contibller failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SLC-3-STOPBIDITO Stop BIDI clock timed out
Explanation An attempt was made to stop the clock on the interface between the
Enterprise Systems Connection ESCON processor and the serial link controller The
serial link controller did not indicate that the clock was stopped
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SLC-3-STOPEPTO Stop EP clock timed out
Explanation An attempt was made to stop the clock on the Enterprise System Connection
ESCON processor The serial link controller did not indicate that the clock was stopped
The CIP attempted to stop the bidirectional bus BIN clock
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
410 System Error Messages CIP-SS1802 Error Messages
CIP-SS1802 Error Messages
CIP 551802 error messages related to the common service System Service Interface 551
facility
Error Message %SS18026-DUNP
indicate the hexadecimal Explanation The dump utility displayed this message to
location of the storage dump
Recommended Action This is an informational message No action is required
Error Message %SS1802-3-FATAL_EPROR SSIL_ASSERT failure in
Explanation The CIP Systems Network Architecture CSNA encountered unrecoverable
error conditions that prevented it from continuing its normal operations
Recommended Action Copy the error message exactly as it appears and report itto your
technical support representative
Error Message %3S1802-3-RTN_AJJR Return Address Ox
Explanation This is debug feature to show the return address when an ASSERT is used failure in an inline function It contains extended data related to the subsequent message and information dump
Recommended Action Report the contents of this message along with the information
provided by the subsequent error message to your technical support representative
CIP System Error Messages 411 CIP-SUBSYS Error Messages
CIP-SUBSYS Error Messages
Software subsystem error messages
Error Message %StJBSYS2-BADCLASS Bad subsystem clas ignoring subsystem
Explanation software consistency check failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SUBSYS-2-BADSEQUENCE Subsystem has cross-class sequence for
Explanation software consistency cheek failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SUBSYS-2-BADVERSION Bad subsystem version number ignoring subsys tern
Explanation software consistency cheek failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SUBSYS-2-MAXRECUR leo many levels of recursion
Explanation software consistency check failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
412 System Error Messages CIP-SYS Error Messages
Error Message %SUBSYS-2-MISMATCH Kernel and subsystem version differ ignoring subsystem
Explanation software consistency check failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SIJBSYS-2-NOTFOUND Subsystem needs subsystem to start
Explanation software consistency check failed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIPSYS Error Messages
CIP operating system error messages
Error Message %SYS-3-BADBLCCK Bad block pointer
Explanation At the indicated location block of memory is corrupt
the it Recommended Action If this message recurs copy error message exactly as
appears and report it to your technical support representative
Error Message %SYS-3-BADFREEMAGIC Corrupt free block at magic
location Explanation block of memory is corrupt at the indicated
Recommended Action If this message recurs copy it exactly as it appears and report it
to your technical support representative
CIP System Error Messages 413 CIP-SYS Error Messages
Error Message %SYS-3-BATJFREEPTRS Bad pointer at hex
Explanation pointer in the block header at the indicated location is corrupt
Recommended Action If this message recurs copy it exactly as it appears and report it
to your technical support representative
Error Message %SYS-3-3ADM7GIC Corrupt block at magic
Explanation The free memory pool is corrupted
Recommended Action Copy the en-or message exactly as it appears and report it to your
technical support representative
Error Message %SYS--2-BADSHARE Bad retcount in ptr count
Explanation An internal software error occurred
Recommended Action If this message recurs copy the error message exactly as it
appears and report it to your technical support iepresentative
Error Message %SYS-6-BLKINFO words alloc dealloc rfcnt
Explanation An internal software error occurred
Recommended Action If this message recurs copy the error message exactly as it
appears and report it to your technical support representative
414 System Error Messages CIP-SYS Error Messages
Error Message %SYS-2--FREEBAD Attempted to free memory at not part of buffer pool
Explanation An internal software error occurred
Recommended Action If this message recurs copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-2-FREEFREE Attempted to free unassigned memory at alloc dealloc
Explanation An internal software error occurred
Recorn mended Action If this message recurs copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS3--INIJSEFREE Block on free list in use
Explanation An internal software error has occulTed
Recommended Action If this message recurs copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-3-INVMEMINT Invalid memory action at interrupt level
Explanation memory allocation or deallocation was attempted from an interrupt handler
Recommended Action If this message recurs copy the error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 415 CIP-SYS Error Messages
Error Message %SYS-2-LONMEM Low memory debug exception iiniit free
Explanation The CIP is running short on memory
Recommended Action You might need to free some memory by quitting program If
this message recurs copy it exactly as it appears and report it to your technical support
representative
Error Message %SYS-2--MRMTOOSMALL CIP software requires minimum of BNB of DRAM
Explanation The UP software has become so large that MB of dynamic RAM DRAM is insufficient The CIP software will not run
Recommended Action Contact your technical support representative Free 8-MB upgrades are available
Error Message %SYS-6--WPRACE addr pc\n ADDRPC ADDRPC ADDRPC ADDRPC \n ADDRPC ADDRPC ADDRPC ADDRPC
Explanation The free memory pool is corrupted
Recommended Action If this message occurs again copy it exactly as it appears and
report it to your technical support representative
Error Message %SYS-2--NOMEMFRG Memory fragmentation check debug exception fragment size
Explanation The system detected an error-checking memory fragmentation
Recommended Action If this message recurs copy the error message exactly as it
appears and report it to your technical support representative
416 System Error Messages CIP-SYS Error Messages
Error Message %SYS-2-NOMEMORY No memory available for
of Explanation An operation could not be accomplished because low memory condition
Recommended Action Reduce other system activity to ease memory demands If conditions warrant upgrade to larger memory configuration
Error Message %SYS-3-NZREFCNT Block on free list with ref count
number Explanation block of memory in the free pooi is in use The of processes using the memory block is indicated
Recommended Action If this message recurs copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-3--OVERRUN Block overrun at redzone
Explanation An internal software error occurred
Recommended Action If this message recurs copy the error message exactly as it appears and report it to your technical support representative
Error Message %SYS-5-RELOAD Reload requested
Explanation reload or restart was requested
Recommended Action Informational message No action is required
Error Message %SYS-5---RESTART System restarted -\n
Explanation reload or restart was requested
Recommended Action Informational message No action is required
CIP System Error Messages 417 CIP-SYSMGT Error Messages
Error Message %SYS-3-WRONGFREELIST Block size on wrong free list
Explanation freed buffer has been placed on the wrong list of free buffers
Recommended Action If this message recurs copy it exactly as it appears and report it
to your technical support representative
CPeSYSMGT Error Messages
CIP error messages related to network management processing for system management
remote procedure calls
Error Message %SYSMGT_RPC3-ERROR Error detected
Explanation An error was detected in the systems management remote procedure call
processing
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYSMGT_RPC-3ilPCjRROR failed
Explanation The system management remote procedure call operation failed Requests
for information from the CTP card will not be processed
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
Error Message %SYSMGTRPC-6-STATESHANGE System Management
Explanation The CIP system management subsystem has changed state
Recommended Action This is an informational message No action is required
418 System Error Messages CIP-TCPIP Error Message
CIP4CP1P Error Message
TCP/IP CIP error message
Error Message %TCPIPO-PANIC panic in
Explanation An unexpected internal error occurred in the TCP/IP stack
Recommended Action Copy the error message exactly as it appears and report it to your
technical support representative
CIPTN327O Error Messages CIP These error messages relate to the TN3270 server feature of the card
Error Message %TN3270S4-BAD_MALLUSSFG Could not change maximum LUs to
Explanation The TN3270 server could not change the maximum number of logical units
LUs to the requested value The previous number is still in use
Recommended Action Review the previous error messages to discover what caused the
failure Take action based on those messages
Error Message %TN3270Si-LISTENFAIL Listening on Failed
Explanation An attempt was made to bring up physical unit PU but listening on
corresponding TCP/IP port could not be initialized
is the card If Recommended Action Verify that sufficient memory available on CIP the inadequate memory does not appear to be the problem copy error message exactly as
it appears and report it to your technical support representative
CIP System Error Messages 419 CIP-TN3270 Error Messages
Error Message %TN327OS1-NOBIND_REQRCVD No BIND REQ received on LU
Explanation The TN3270 session did not receive BIND REQUEST or system services host within of control point SSCP-logical unit LU data from the 30 seconds the start Of
the If condition the SSCP-LU session The host should have sent one or other this persistsI
for another minutes the LU is declared bad Bad dynamic LUs are not reused until all
good dynamic LUs associated with the Internet Protocol IP listening point are in use
Recom mended Action Examine the SSCP host VTAM console for the status of the
specified PU and LU Review the VTAM console log output for relevant events such as the
deactivation of the PU or LU If the cause of the problem is still unknown after you review
it and it the VTAM console copy the error message exactly as appears report to your
technical support representative temporary workaround is to recycle the affected LU at
the VTAM console to return the LU to normal circulation
Error Message %TN3270S-1-NOJJYNACTLU_REQRCVD No ACTLU REQ received on LU
Explanation The host has not sent an ACTLU Activate LU request within minute of
sending Reply PSID product-set identification response If this condition persists for
another minutes the current TN3270 session will be disconnected from the logical unit
LU and the LU will be declared bad Bad dynamic LUs are not reused until all good
dynamic LUs associated with the Internet Protocol IP listening point are in use
Recommended Action Examine the system services control point SSCP host Virtual
Telecommunications Access Method VTAM console for the status of the specified PU
and LU Review the VTAM console log output for relevant events such as deactivation
of the PU or LU If after the VTAM console review the cause is still unknown copy the
error message exactly as it appears and report it to your technical support representative
As temporary workaround recycle the affected LU at the VTAM console to return the LU
to normal circulation
420 System Error Messages CIP-TN3270 Error Messages
Error Message %TN3270S-l-NO_EVENT_BUFS No IPC sysmgt event buffers for at least one minute
Explanation TN3 270 server has events that result in Simple Network Management
Protocol SNMP traps and/or Systems Network Architecture SNA alerts but has not been able to allocate interprocess communication IPC buffer resources to report the events to the router system code The TN3270 server will persist in attempting to report
these events but lack of buffers might continue to be problem until the CIP microcode is reloaded
Recommended Action Copy the error message exactly as it appears and copy the output from the following commands
show ipe status
show ipe queue
show ipc ports
show ipc nodes
show controllers cbus
show version
Report this information to your technical support representative As workaround reload the CIP microcode
Error Message %TN3270S-i-NO_LU_MRMORY No memory on the CI was available for completing requested Th3270 LU session
Explanation Not enough memory is available to the TN3270 server to complete one or more requests by TN3270/E clients for logical unit LU sessions The sessions have been disconnected
Recommended Action Review the memory requirements needed to run the TN3270
client load Install additional if server application considering the current memory
necessary
CIP System Error Messages 421 CIP-TN3270 Error Messages
Error Message %TN3270S4--NO_LtLSESSIONS No LU sessions left for Pus at IP addr port
Explanati n The TN3270 server cannot complete one or more connection requests from
TN3270/E client because no more logical units LUs are available in the generic pool
associated with the specified Internet Protocol IP listening point address
Recommended Action Review the LU requirements for this applications endpoints
units listen to Configure additional physical PUs to the specified IP address and port number
Error Message %TN3270S-1-NCNTFYAV_RSPRCVD No NQTIFYavaiiable RSP received on LU
Explanation The TN3270 server did not receive response to power-on AVAILABLE
NOTIFY request within 30 seconds of sending it to the host If this condition persists for another minutes the current TN3 270 session connected to the logical unit LU will be
disconnected and the LU declared bad Bad dynamic LUs are not reused until all good
dynamic LUs associated with the Internet Protocol IP listening point are in use
Recommended Action Examine the SSCP host YTAM console for the status of the
Review console for relevant specified physical unit PU and LU VTAM log output events
such deactivation of the PU or LU If after VTAM console review the cause is still
it and it technical unknown copy the error message exactly as appears report to your
support representative temporary workaround is to recycle the affected LU at the VTAM
console to return the LU to normal circulation
422 System Error Messages CIP-TN3270 Error Messages
Error Message %TN3270S1--NO_NTFYUARSPRCVD No NOTIFYUA RSP received on LU
Explanation The host failed to reply within 30 seconds of when the TN3270 server sent
power-off UNAVAILABLE NOTIFY request If this condition persists for another minutes the current TN3270 session will be disconnected from the logical unit LU and the LU will be declared bad Bad dynamic LUs are not reused until all good dynamic LUs
associated with the Internet Protocol IP listening point are in use
Recommended Action Examine the system services control point SSCP host Virtual
Telecommunications Access Method VTAM console for the status of the specified physical unit PU and LU Review the VTAM console log output for relevant events such
as deactivation of the PU or LU If after the YTAM console review the cause is still
unknown copy the error message exactly as it appears and report it to your technical
support representative As temporary workaround recycle the affected LU at the VTAM
console to return the LU to normal circulation
Error Message %TN3270S-l-NPSIDRSPRCVD No NMVT Reply PSID received on LU
Explanation The host failed to send response within minute of when the TN3270
server sent Reply PSID This fault can occur only on dynamic logical units LUs that
have been misconfigurcd or deactivated at the host If this condition persists for another
minutes the current TN3270 session will be disconnected from the LU and the LU will
be declared bad Bad dynamic LUs are placed in special area where they are not allowed
to be reused until all the other generic pool LUs of the listening Internet Protocol IP have been exhausted
Recommended Action Check the status of the LU using Virtual Telecommunications
Access Method VTAM and vary the active LU if appropriate This action must happen
within minutes of the time this message appears otherwise the LU is placed in the bad
LU area and will not be reused unless all good LUs are in use Examine the host VTAM log
for errors or problems In particular look for messages indicating badly configured
LUGROUP resource definition or file Fix the configuration and recycle the affected major nodes
CIP System Error Messages 423 CIP-TN3270 Error Messages
Error Message %TN3270S-i-NO_SDT_REQ_RCVD No GUT REQ received on LU
Explanation The TN3270 server received TN3270 no SDT Start Data Traffic request
from the primary logical unit PLU host for the specified logical unit LU If this condition
persists for another minutes the LU is declared bad Bad dynamic LUs are not reused
until all good dynamic LUs associated with the Internet Protocol IP listening point are in use
Recommended Action Examine the SSCP host VTAM console for the status of the
specified PU and LU Review the YTAM console log output for relevant events such as the
deactivation of the PU or LU If the cause of the problem is still unknown after you review
the YTAM console copy the error message exactly as it appears and report it to your
technical support representative temporary workaround is to recycle the affected LU at
the VTAM console to return the LU to normal circulation
Error Message %TN327OS-1-NO_SDT_TMARKjCVD No GUT TIMING-MARK received on LU
Explanation No SDT Start Data Traffic TIMING-MARK response was received by the
TN3270 server from the TN3270 client software for the specified TN3270 scssion If this
the unit is declared Bad condition persists for another minutes logical LU bad dynamic
LUs are not reused until all good dynamic LUs associated with the Internet Protocol IP
listening point are in use
Action clients not handle the Recommended Some TN3270 may frilly TN3270 Requests
for Comments RECs Enable the client-side trace to discover where the client is failing
Replace the failing client software with software from the list of TN3270 software types
known to work with the TN3 270 server If you have any questions about which software to
use or if the problem persists copy the error message exactly as it appears and report it to
your technical support representative
424 System Error Messages CIP-TN3270 Error Messages
Error Message %TN327US-l-NO_UNBIND_RSPRCVD No UNBIND RSP received on LU
Explanation The host failed to reply within 30 seconds of when the TN3270 server sent an UNBIND request If this condition persists for another minutes the current TN3270
session will be disconnected from the logical unit LU and the LU declared bad Bad dynamic LUs are not reused until all good dynamic LUs associated with the Internet
Protocol IP listening point are in use
Recommended Action Examine the system services control point SSCP host Virtual
Telecommunications Access Method VTAM console for the status of the specified PU
and LU Review the VTAM console log output for relevant events such as deactivation
of the PU or LU If after the VTAM console review the cause is still unknown copy the technical error message exactly as it appears and report it to your support representative the the As temporary workaround recycle the affected LU at VTAM console to return LU
to normal circulation
Error Message %327QS-i-NC_UNBINQTMARK_RCVD No UNBIND-time TIMING-MARK received from client for LU
Explanation No UNBIND TIMING-MARK response was received by the TN3270 server
from the TN3270 client software for the specified TN3270 session If the condition persists
unit is declared bad Bad are not for another minutes the logical LU dynamic LUs reused until all good dynamic LUs associated with the Internet Protocol IP listening point
are in use
Recommended Action Some TN3270 clients may not fully handle the TN3270 Requests For Comments RFCs Enable the client-side trace to determine where the client is failing
Replace the failing client software with software from the list of TN3270 software types
that are known to work with the TN3270 servet If you are uncertain about which software
it to use or if the problem persists copy the error message exactly as it appears and report
to your technical support representative
CIP System Error Messages 425 CIP-TN3270 Error Messages
Error Message %TNB27OSl-RP_PU_CONFLICT RP SIP hold conflicting PU narne or index%id
Explanation The Route Processor RP requested an update or delete action on physical unit PU resource reported as stale or incorrect by the CIP TN3270 server
Recommended Action Reload the CIP microcode If the problem occurs again copy the from the error message exactly as it appears Run and record tile output following
commands on each CIP in the router before reloading the CIP microcode
show extended chan siotl2 tn3270
show controllers elms
show running-config
Report this information to your technical support representative
Error Message %Th3270S--l-START_FAIL Failed to start Tn3270server
Explanation The TN3270 server failed to start correctly and is not now running The
immediately preceding error messages indicate the cause of the failure
Recommended Action Review the previous error messages to discover what caused the
start failure Take action based on those messages
Error Message %TN3270S-6-START_OK Starting Tn3270-server
Explanation This is an informational message The TN3270 server subsystem is now operating
Recommended Action No action is required
426 System Error Messages CIP-TN3270 Error Messages
Error Message %TN3270S6-STOPPINC Stopping Th327cY-server
Explanation The TN3270 server subsystem is shut down This is an informational message
Recommended Action No action is required
Error Message %TN327OS-OTEbNETINITFAIL Initialization of TN3270 server Failed
Explanation Initialization of the TN3270 server Telnet component failed probably because of inadequate memory on the CIP card
Recommended Action Check the CIP card memory If inadequate memory does not appear to be the problem copy this error message exactly as it appears and report it to your technical support representative
CIP System Error Messages 427 CIP-TN3270 Error Messages
428 System Error Messages System Failure Error Messages
that such This section covers other types of error messages you may encounter as bus parity timeout unexpected and unknown error messages
These error messages result when the system image crashes either from hardware or software failure To access these messages use the bootstrap program
When you encounter timeout bus error or unknown error message you must run the stack trace command at the bootstrap mode prompt to display the stack trace results
In the following example timeout error message appears the stack trace command is run but no stack trace results
Timeout control regOxCF1O Error address OxFFFFFFE8 at Ox317IJ49E PC
No stack to dump NULL frame pointer
the stack command is In the following example an unknown en-or message appears trace run and stack trace results
Unknown control regOxlO Error address OxDODODOD at Ox3l3DC22 PC
Current PC Ox313DC22 FP OxE662O RA Ox3l4llAB FP OxE6634 RA Ox3l23DlC FP OxE6GSO RA Ox3l23O3A FP OxE6668 RA 0x3l33664 FP OxEGG7C RA 0x3l337U2 FP QxE6694 RA Ox31349DA FP OxE66AO HA Ox3O14B4C
System Failure Error Messages 429 Table describes the fields in this sample stack trace
Table Stack Trace Fields
Field Description
Current PC Address at which the failure occurred This address is
Ox313DC22 also called the program counter PC
FP CxE662O Stack frame pointer
RA Dx3 141 1A8 Program counter of calling function saved in stack
frame This value is used to trace the flow of software
function calls leading to the failure
After you obtain the stack trace use the initialize command before you manually boot
up the system image Then use the show version command when possible to identify the
software release and version number for use by technical staff
On systems that have hardware or virtual software configuration register and the boot
than the bits lowest four bits set to value greater system will repeatedly try to boot up the resident Flash appropriate system image from ROMs memory or server over the
network If the booting is successful the system prompt appears You then can use the show
stack command to obtain the stack trace
In cases where the router crashes repeatedly send Break character from the console
keyboard to obtain the bootstrap mode prompt Then modify the configuration register boot
bits to zero enter the initialize command and manually attempt to bootstrap the system
image If it crashes use the stack trace command
430 System Error Messages Error Message Bus Error control register non-local memory transaction timeout Bus Error address at PC
Explanation An invalid memory address is accessed either because of software bug or because boot of an incompatible software image was attempted
Recommended Action If the error occurred when your tried to boot up system image over the network or from reprogrammed Flash memory probable reason could be the use of wrong or incompatible system image Look in the appropriate documentation to find
If still contact out which system image to use you need assistance your technical support representative with the following details
Name of the system image file used for booting as obtained from the technical support
representative
Product name and configuration
show version output from any bootable RUM-based image available on the system
bootstrap image for example
If the error occurred while trying to boot up built-in RUM-based image contact your technical support representative with the following details
Product name and configuration
Any hardware/software upgrades that were made prior to the failure
Anything else that you think will help your technical support representative diagnose the problem
Any stack trace if obtainable using the command at the bootstrap prompt
If the error occurred while the system was operational contact your technical support representative after gathering the following information
Any stack trace obtained using the command at the bootstrap mode prompt or if
the system successfully rebooted itself show stack output
show version output obtained after rebooting the system image in which the failure occurred
System Failure Error Messages 431 Error Message Bus Error control register
rain byte parity error Bus Error address at PC
has Explanation Memory corruption or failure occurred most likely because of
hardware problem or by disturbances such as power line problems
Recommended Action Reboot the system and observe whether the problem recurs Also
ensure that the power line has appropriate protection equipment If the problem is one-time occurrence the cause could be power line disturbance
Error Message Bus Error control register system overtemp Bus Error address at PC
Explanation Temperature exceeded the operating range most likely because of
ventilation air-conditioning or hardware problem
Recommended Action Power off the system and give it time to cool Check room
ventilation and air conditioning Also ensure that system air-flow grids are not blocked and
that blowers are operational Call your technical support representative if blower needs replacement
Error Message Local Timeout control reg Error address at PC
Explanation An invalid memory address is accessed either because of software bug or
because boot of an incompatible software image was attempted
Recommended Action Refer to the RecommendedAction for the first Bus Error control
register message in this section
432 System Error Messages Error Message Multibus Timeout control reg Error address at PC
Explanation An invalid memory address is accessed either because of software bug or because of incompatible microcode in multibus card
Recommended Action Reseat the card If this message recurs call your technical support representative for assistance
Error Message Parity control reg Error address at PC
because of Explanation Memory corruption or failure has occurred most likely hardware problem Disturbances such as power line problems are also possibilities
Recommended Action Reboot the system and observe whether the problem recurs Also ensure that the power line bas appropriate protection equipment If the problem is one-time occurrence the cause could be power line disturbance
for assistance If this message recurs call your technical support representative
Error Message Shared Memory Parity Error shared memory control register error caused by slot access in bytes
Shared Memory Parity Error shared memory control register error caused by MPU access in bytes
Explanation Shared I/O memory failure or corruption occurred during access by the
hardware failure disturbances such processor This problem is most likely due to or by as power line problems
Recommended Action Reboot the system and observe whether the problem recurs Also ensure that the power line has appropriate protection equipment If the problem is one-time occurrence the cause could be power line disturbance
System Failure Error Messages 433 Error Message Unexpected exception to Cpu vector PC
Explanation Either hardware or software problem has occurred
Recommended Action Refer to the Recommended Action for the first Bus Error controI
register message in this section
Error Message Unexpected vectored interrupt vector offset
Explanation Either hardware or software problem has occurred
Recommended Action Refer to the RecommendedAction for the first Bus Error control
register message in this section
Error Message unknown control reg Error address at PC
Explanation Either hardware or software problem has occurred
Recommended Action Refer to the RecommendedAction for the first Bus Error control
register message in this section
434 System Error Messages INDEX
ARAP-3-NOMEM 11
ARAP-5-PAKIN VALID 11 AAAA-3-BADSTR ARAP-4-TIMEOUT ii AAAA-3-NULUSR AT-6-ACQUIREMODE 11 AAAA-3-RELOGIN AT-5-ADDRINUSE 12 AT-5-ADDRINVALID 12 AJP-3-AIPFAILSETUPVC AT-6-ADDRTJSED 12 AIP-3-AIPFAILSETUPVCAVG AIP-3-AIPREJCMD AT-2.-ASSERTFAILED 12 ALIGN-3-CORRECT AT-5-BADNEIGHBOR 13 AT-BADROUTE 13 ALIGN-i-FATAL AT-7-BUGREPORT 13 ALIGN-3-FULL AT-3-CANTDEL 14 ALIGN-3-NOMEM AT-5-COMPATERR 14 ALIGN-3-SPURIOUS ALIGN-3-UNUSUAL AT-5COMPATERR2 14 AT-.5-COMPATERR3 APPN- -APPNALERT 15 AT-5-COMPATERR4 15 APPN-2-APPNCRTT AT-6-CONFIGOK 15 APPN-7-APPNDEBUG APPN-0-APPNEMERG AT-6-CPUPIG 15 APPN-3-APPNERR AT-7-DEBUGMSG 16 AT-3.-DEFZONEERR 16 APPN-7-APPNETERROR AT-6-DELROUTE 16 APPN-3-APPNETLOG AT-5-DISCOFF 16 APPN-6-APPNINFO AT-3-DOMLOOP 17 APPN-6-APPNLOGMSG APPN-5-APPNNOTICE AT-3-DOMOVERFLOW 17 AT-5-DUPADDR 18 APPN-7-APPNSENDE VENT AT-6-EIGRPLthKDN 18 APPN-6-APPNSENDMSG AT-6-EIGRPLINKUP 18 APPN-5-APPNSENDREQ AT-6-EIGRPLOG 18 APPN-4-APPNWARNING APPN-7-MSALERT AT-4-EIGRPLOTSO WORK 19 AT-6-EIGRPPEERDN 19 ARAP-3-ABORTED AT-6-BIGRPPEERIJP 19 ARAP-6-ADDRFREE AT-5-FDDICOMPAT 19 ARAP-6-ADDRIJSED AT-3-IFCONFLICT 20 ARAP-3-BADCONFIG ARAP-6-BADEXIT AT.5-1NTCLEARED 20 AT-5-INTDOWN 20 ARAP-3-BADPAK AT-5-INTRESTART 20 ARAP-4-CONFAILED 10 AT-6-llTTUP 21 ARAP-4-GETBUFFER 10 AT-3-INVNBPCMD 21 ARAP-5-INITCONFUSED 10 AT-5-LOSTNEIGHBOR 21 ARAP-4-NOEXTTACACS 10
Index AT-ThMACIPBADCONF 21 AT-3-SUBROUTINE ERROR 31
AT-6-MACIPDOWN 22 AT-3-ZONIEDISAGREES 31
AfThMACIPNOCABLE 22 AT-6-ZONEGC 31
AT-6-MACIPUP 22 AT-6-ZONEPROXY 32
AT-3MCMIS MATCH 23
ATM-3-FAILCREATEVC 32
ATM-4-MTUCALLMISMATCH 33 ATMA-NOMEM 33 ATM-3-UNSUPPORTEDQOS_PARAMS 34 BGP-6-ASPATH 34 AT-6-NBRDELETED 23 BGP-3-BADMASK 34 AT-6-NEIGHJ3ORUP 23 BGP-6-NEXTHOP 35 AT-3NETDISAGREES 23 BGP-3-NOMEMORY 35 AT-4-NETIN VALID 24 BGP-3-RADTXINIT 35 AT-6-NEWNEIGHBOR 24 BRI-3-BADENCAP 36 AT-6-NEWROUTE 24 BRI-3-BADUNIT 36 AT-6-NEWZONE 24 BRI-1-INITFAIL 36 AT-3-NOADDRSA VAIL 25 BRI-0-NOMEMORY 36 AT3-NOBESTPATH 25 BRT-3-ODDSTART 36 AT-6-NODEWRONG 25 BRI-3-OUTENCAP 37 AT-1-NOMEM 25 BRI-3-OWNERR 37 AT-6-NOPROXY 26 BSC-3--BADLJNESTATE 37 AT-3-NOROIJTE 26 BSC-3--BADPEERTYPE 37 AT3-NOSRCADDR 26 BSC-2-NOMEM 38 AT.-3-NOSUCHNBR 26 BSTUN-.3-BADCONN 38 AT5-NOSUCHROUTE 27 BSTUN-3-BADLENOP 38 AT-3-NOTRUNNING 27 BSTUN-3-BADMAGIC 38 AT-5-NOTSUPPORTED 27 BSTUN-3BADMAGICTCP 38 AT-3-NO VIRTUAL 27 BSTUN-3-BADPASSIVEOPEN 38 AT-5-OLDMCI 28 BSTIJN-3CONN1LLSTATE 38 AT-6-ONLYROUTER 28 BSTUN-6-CONNOPENFAIL 39 AT-6-OUTOFSYNC 28 BSTUNERR 39 AT-6-PATHADD 28 BSTUN-2-NOBUF 39 AT-5-PATHCFIANGE 29 BSTUN-3--NOGRPDEF 39 AT-6-PATHDEL 29 BSTUN-3-NOPROTMEM 40 AT-6-PATHNOTIFY 29 BSTUN-6-OPENED 40 AT.4.PATHREJECTED 29 BSTUN-6-OPENING 40 AT-6-REGPENDIP4G 30 STUN-6-PASSIVEOPEN 40 AT-6-ROUTEDOWN 30 BSTUN--PEERSHUTDOWN 40 AT6-ROUTENOT1FY 30 BSTUN-4-.PEERSTATE 41 AT-6-ROUTEOK 30 BSTUN-6-.PROCEXIT 41 AT-5.-RTMPSTATE 31
System Error Messages BSTUN-6-RECONNBCT 41 CBUS-3-CTRACHECK 48
BSTUN-3-SENDPUNT 41 CBUS-3-CTRCMDFAILED 48
BSTUN-3-SENDPUNflCP 41 CBUS3-CTRCMDFAThED2 49
BSTUN-6-TCPFINI 42 CBUS-3-CTRINIT 49 BSTUN-6-TCPPEERSHUT 42 CBUS-3-CTRLRCMDFAILO 49
BSTUN-3-UNKPROTOEV 42 CBUS-3-CTRLRCMDFAIL1 49
Bus Error control register non-local memory CBUS-3-CTRLRINTTERR 50
transaction timeout Bus Error address at CBUS-3-CTRRAMTEST 50 PC 431 CBUS-3-CTRRESET 50
Bus Error control register ram byte parity CBUS-3-CTRUCHECK 50
error Bus Error address at CBUS-3-DAUGHTER 51 PC 432 CBUS-3-DAUGHTER_NQRSP 52
Bus Error control register system overtemp Bus CBUS-3-FCICMDFAILO 52
Error address at PC 432 CBUS-3--FCICMDFAIL1 53 CBUS-3-FDDIRSET 53
CBUS-3-FDDIRSETU 53
CBUS-3-FSIPRSET 53
CBUS-3-GHOST 53
CBUS-3-HSSIRSET 54 CBUS-3-AIPCFG 43 CBUS-3-HSSIRSETU 54 CBUS-3-ATPINVPLIM 43 CBUS-3-INITERR 54 CBUS-3-AIPRSET 43 CBUS-3-INTR 54 CBUS-3-AIPRSETU 43 CBUS-4-INTR 54 CBUS-4-BADENCAPSZ 43 CBUS-3-MEC_OUTHUNG 54 CBUS-3-BIQBUF 43 CBUS-3-MIPSTAT 55 CBUS-3-BUFFER 44 CBUS-3--MODULE 55 CBUS-3-CBUSBCE 44 CBUS-3-NOBUF 55 CBUS3-CBUSBCEPERM 44 CBUS-4-.NOCOOKIE 55 CBUS-3-CCBCMDFAILO 44 CBUS-3-NOMEMORY 56 CBUS-3-CCBCMDFAIL1 45 CBUS-3-OUTHUNG 56 CBUS-3-CCBPTIMEOUT 45 CBUS-4-OUTHUNG 56 CBUS-3-CCBREPLY 45 CBUS-3-POLLFAIL 56 CBUS-4-CIPADPTCHNG 45 CBUS-3-POLLFAILDAT 57 CBUS-3-CIPCFGFAIL 46 CBUS-3-PORTTYPE 57 CBUS-3-CIPDTRPAIL 46 CBUS-3-RESETNXI 57 CBUS3-CIPENCAP 46 CBUS-4-RSETFAIL 57 CBUS-3-CIPNOPREQ 46 CBUS-3-SELECT 58 CBUS-3-CTPRSET 47 CBUS-3-TESTFAIL 58 CBUS-3-CMD 47 CBUS-3-TXALLOC 58 CBUS-3-CMDTIMEOUT 48 CBUS-3-UNKENC 58 CBUS.-3-CORRUPT 48 CCP-4-NOBUF 59
Index CI3-BLOWER 59 CIP.-CCA-0-BSQFULL 329
CI-1-BLOWSHUT 60 CIP-CCA-3-BYPASS 329 CI-6-BPLANB 60 CIPCCA-.3--CANCEL1 330 CI-4-COND 60 CIP-CCA-3-CANCEL2 330 CI-3-CTRLRTYPE 61 CIP-CCA.-3-COMMAND_PATH 330 C1-2-ENVCRIT 61 CIP-CCA-3-CONN.RESULT 331 CI-4-ENVWARN 61 CIP-CCA-0-DEVERRI 331
CI-3-NOACK 62 CIP-CCA-0-DEVERR2 331 C1-4-NOTFOUND 62 CIP-CCA-0-DEVERR3 331
CJP-ADAPTER-4-BADREQIJEST 320 CIP-CCA-3-END_STAT1JS 332
CIP.-ADAPTER-6-BADSTATE 320 CIP-CCA-3-LOGOUT 332
CIP-ADAPTER-6-DIAGBEGIN 320 CIP-CCA-3--REQUEST_STATUS 332 CIP-ADAPTBR-0-DIAGDATA 321 CIP-CCA-3-RESETJATH 332
CIP-ADAPTER-6-DIAGDATA2 321 CIP-CCA-3-RLP1 333
CIP-ADAPTER-0-DIAGFAIL 321 CIP-CCA-3-RLP2 333
CIP-ADAPTER-6-DIAGFATL2 321 CIP-CCA-0-SCBNRDY 333
CIP-ADAPTER6-DIAGGOOD2 322 CIP-CCA-3-SEL_RESET1 333 CIP-ADAPTER-6-DIAGRANGE 322 CIP-CCA-3-SEL_RESET2 334 CIP-ADAPTER-6-DIAGSTOP 322 CIP-CCA-3-STATUSNOTICE 334 CIPADAPTER-O-DIAGTERM 322 CIP-CCA-3-SYS_RESET 334 CIP-ADAPTER-6-DIAGTERM2 323 CIP-CCA--0-TOOMANY 334
CW-ADAPTER-0-LOADFAIL 323 CIP-CCA-3-WRAPPLUG 335
CIP-ADAPTER-6-LOGDATA 323 CIP-CCA-0-WRITE_FAIL 335
CIP-ADAPTER-6-L000UT 323 CIP-CLAW-0-BADAPPL 335
CIP-ADAPTER-6-LOGSAME 324 CIP-CLAW-0-J3ADAPPL2 336
CIP-ADAPTER-6-SCAN 324 CIP-CLAW-6-BADCHAIN 336
CIP-ADAPTER-6--SCANDATA 324 CIP-CLAW-0-BADHAPPL 336 CIP.-ADAPTER-0-START_FAIL 324 CJP-CLAW-0-BADHNAME 336
CIP-ADAPTER-6-WRAP 325 CIP-CLAW-0-BADRSIZE 337
CIP-ADAPTER-6-WRAPSTOP 325 CIP-CLAW-6-BADSVR 337
CIP.-ADAPTER-6-WRAPSTOP2 325 CIP-CLAW-0-BAD VERSION 337 CIPBSQ-0--SCB_CHAIN 325 CIP-CLAW-0-BADWAPPL 337 CIP-BSQ-0-TOOMANY 326 CIP-CLAW-0-BADWNAME 338 CIP-CBUS_ATTN-3-BADADDR 326 CIP-CLAW-0-BADWSIZE 338 CIP-CBUS_WRIT3-.BADTYPE 327 CIP-CLAW-6-COMMAND 338 CIP-CBIJS_WRITE-3-IN VALID 327 CIP-CLAW-6-LONGREC 338
CIP-CBUS_WRITE-3-MISSJNG 327 CIP-CLAW-6-NOCONN 339 CIP-CBUS_WRITE-3-STACK 328 CIP-CLAW-0-NOLINKID 339 CIP-CBUS_WfflTE-3UNEXPECTED 328 CIP-CLAW-6-NOTPRESENT 339
CIP.-CCA-3--ACR 328 CIP-.CLAW-6-NOTXBUF 339 CIP-CCA-0-BADCCA 329 CIP-CLAW-6-RANGE 340
System Error Messages CIP-CLAW-6-TOOBIG 340 CIP-CTA-6-FLUSH 350
CIP-.CLIAW-6-TYPE 340 CIP-CTA-6-llTIT 351
CIP-CLAW- 6-UNEXPECTED 341 CIP-CTA-6-LONGREC 351
CIP-CLAW-6-VIRTCLAW 341 CIP-CTA-0-MSGERRI 351 CIP-CONFIG-6-BAD_DBTYPE 342 CIP-CTA-0-MSGERR2 351 CIP-CONFIG-6-BADCONPIG 342 CIP-CTA-0-MSGERR3 352
CIP-CONFIG-6-BADDEVT 342 CIP-CTA-0-NOMEM 352
CIP-CONFIG-0-BADSPEED 343 CIP-CTA-0-QUBUE_ERROR 352
CIP-CONFIC-3-BADVCN 343 CIP-CTA-6-SHUTDOWN 352
CIP-CONFIG-3-BADVCN2 343 CIP-CTA-0-SYSMGT_ERROR1 353 CIP-CONFIG-3-CLAWDEV 343 CIP.-CTA-0-SYSMGT_ERROR2 353 CIP-CONFIG-3-CONFIGINIT 344 CIP-CTA-0-SYSMGT_ERROR3 353 CIP-CONFIG-3-DIFFDEVT 344 CIP-CTA-0-UNEXP_CTA_CMD 354 CIP-CONFIG-3-DUPDEV 344 CIP-CTA-0-UNEXP_E VENT 355 CIP-CONFJG-3-DUPVCN 344 CIP-CTA-0-UNEXP_LSIJ2MD 355 CIP-CONFIG-3-NOAPPLESPC 345 CIP-CTA-0-UNEXP_LSI_STATUS 355 CIP-CONFIG-3-NOCONFIG 345 CIP-DEBUGGER-0-CIP_HWVINFO 356 CJP-CONFIG-3-NOCUT 345 CIP-DEBUGGER-0-CIP_SWVINFO 356
CIP-CONFTG-3-NODEV 345 CIP-DEBUGGER-0-FATAL_ERROR 356
CIP-CONFIG-3-NODEVSPC 346 CIP-DBBUGGER-0-LCORE_DATA 357 CIP-CONFIG-3-NOFREBPATH 346 CIP-DEBUGGER-0-LCORESTART 357 CIP-CONFIG-3-NOPATHSPC 346 CIP-DEBUGGBR-0-RESTART 357 CIP-CONFIG-3-NOSPACE 346 CIP-DEBUGGER-0-STACKDATA 358 CIP-CONFIG-3-NOVCN 347 CIP-DEBUGGER-0-STACKDATA2 358 CIP-CONFIG-3-OIPFLDEV 347 CIP-DEBUGGER-0-STACKjJATA3 358
CIP-CONFIG-3-OFPLOADDEV 347 CIP-DEBUGGER-0-STACKDATA4 358 CIPCONFIG-3-STATEJNIT 347 CJP-DEBUGGER-0-STACK_DATA5 358 CIP-CONFIG-3-TOOMANYDEV 348 CIP-DEBUGGER-0-STACK_DATA6 358
CIP-CONFIG-3-UNEXPCFG 348 CIP-DEBUGGER-0-STACK_DATA7 358
CIP-CONFIG-3-WORKLEFT 348 CIP-DEBUGGER-0-STACK_DATA8 358
CIP-CONFIG-3-WRONGINT 348 CIP-DEBUGGER-0-STACK_START 358 CIP-CTA_TEST_TOOL-3-INVALID_CFGBLK 353 CIP-DEBUGGER-0-.TRACE_ADDR 358 CIP-CTA_TESTJFOOL-3-ThTVALIDLEN 353 CIP-DEBUGGER-0-TRACE_DATA 359 CIP-CTA_TEST_TOOL-3-ThJVALIDMBUF 354 CIP-DEBUGGER-0-TRACE_START 359 CIP-CTA_TEST_TOOL-3-NOMEMORY 354 CIP-DIAG-6-BADCODE 359 CIP-CTA-6-BADCHAThJ 349 CIP-DIAG-6-BADLOAD 360
CIP-CTA-0-ERRSTASH 349 CIP-DMA-0-BADFIFO 360
CIP-CTA-0-ERRSTATE1 349 CIP-DMA-3-CBUSERR 360
CIP-CTA-0-ERRSTATE2 350 CIP-DMA-3-CBUS PARITY 361
CIP-CTA-0-ERRSTATE3 350 CIP-DMA-4-DATAPARITY 361
CIP-CTA-0-ERRSTATE4 350 CIP-DMA-0-INCOMPL 361
Index CIP-DMA-3-LOGICBRR 361 CIP-LOADER-3-FOPEN 372
CIP-DMA-0NOXFER 362 CIP-LOADER-3-FOPENBZ 372
CIP-DMA-0-REGJSTERS 362 CIPLOADER-3-FOPENBR 373
CJP-GET_DATA-0-NOMEMORY 362 CIP-LOADER-3-FREADE 373 CTP-INT-0-ADDFAST 363 CIP-LOADER-3--GPPROB 373
CIP-INT-0-ADDFLIH 363 CIP-LOADER-3-GREADE 373
CIP-INT-0-ADDFULL 363 CIPWOADER-3-HDRSIZ 374 CIP-INT-0-ADDTRAP 364 CJP-LOADBR-3-HDRVER 374
CIP-INT-0-REMOVEPAST 364 CIPWOADER-3-HREADE 374 CJP-INT-0-REMOVEFLIH 364 CIP-LOADBR-3-INSUFF 374
CIP-INT-4J--REMOVEFULL 364 CJP-LOADERM4NVALIDIOS 375
CIP-INT-0--REMOVETRAP 365 CJP-LOADBR-6-LOADING 375
CIP4PC2-CONSISTENCY 365 CIP-LOADER-OWOADMAPDATAI 375
CIP-IPC-2-DELETED 365 CJP-LOADER-0-LOADMAP_DATA2 375 CIP4PC2-LOCK 365 CIP-LOADER-OWOADMAPDATA3 376 CIPAPC-2-NOBUFFER 366 CIP-LOADER-0-LOADMAP_EMPTY 376 CIP-1PC2.-NODISPATCH 366 CIP-LOADERM-LOADMAPEMPTY2 376
CIP-IPC-2-NOMEM 366 CIP-LOADER-0-LOADMAP_HEADO 376 CIP-IPC-2-NOMEMD 366 CJPWOADER-11-LOADMAP HEAD 377
CIP-IPC.-2-UNLOCK 367 CJP-LOADER-3-LOADRC 377
CIP-LOADER-3-ABSERR 367 CJP-LOADER34v1AXRSE 377
CIP-LOADER-3-ALOCER1 367 CIP-LOADER-3-MAXSEC 377
CIP-LOADER-3-ALOCER2 367 CIP-LOADER-3-MAXSTRT 378
CIP-LOADER-3-ATFERR 368 CJP-LOADBR-3-MAXSYMT 378
CIPWOADER-3-BADSHT 368 CIPWOADER3-NOBITS0 378
CIP-LOADER-3-BADVERS 368 CJP-LOADBR-3-NODSO 378
CIP-LOADER-3-BAKEXP 368 CIP-LOADER-3-NOELF 379 CJP-LOADER-3-BIGEND 369 CIP-LOADER-3-NOERES 379
CIP-LOADER-3-BJNDERR 369 CJPWOADER-3-NOPREFIX 379
CIP-LOADBR-3-COMERR 369 CJP.-LOADER.-3-NOPRG 379
CIP-LOADER-3-COMMJX 369 CIV-LOADER-3-NOSECH 380 CIP.-LOADER-3-COMPER 370 CJP-LOADBR-3-NOSO 380
CIP-LOADER-.3-DRBADE 370 CIP-tOADER3-NOTRE 380 CIP-LOADER.-3-DUPEXP 370 CIP-LOADBR-3-NOVERS 380
CIP-LOADER-3--ETDENT 370 CJPWOADBR-3-READERR 381
CIP-LOADER-3-ELF32 371 CIP-LOADER-3--RELFLG 381
C1P-LOADER-3-ELFH 371 CIPWOADER3-RELREAD 381
CTP-LOADBR-3-ERRCNR 371 CJP-LOADER-3-RELTYP 381
CIP-LOADER-3-ERR1 6H 371 CIPLOADER-3-RELTYP2 381
CIP-LOADER-3-FCLOSE 372 CIP-LOADER-3-RESERR 382
CIP-LOADER-3-.FILESJZE 372 CIP-LOADER3-SECERR 382
System Error Messages CIP-LOADER-.3-SEEKER 382 dJP-MS0802-6-LLC_SHUT 392
CIP-LOADER-3-SHFLAGE 382 CIP-MSG8O2-6-LLC_START 392 CIP.-LOADER-3-SHNHIPB 383 CIP-MSG8O2-6-LLQUNEXP_ACK 393 CIP-LOADER-3-SHNHTR 383 CIP-MSG8O2-6-MAX_FAILBD 393 CIP-LOADER-3-SIZERR 383 CIP-MS0802-6-MAX_FAILBD2 393
CIP-LOADER-3-SORBBR 383 CIP-MSG8O2-6-MAX_LLC_EXCEEDED 394
CIP-LOADER-3-SREADE 383 CIPMSG8O2-3-ODD_MEMD 394 CIP-LOADER-3-SREADS 383 CIP-MSG8O2-3-QUEUB_OPEN 394 CJP-LOADER-3-STOTHER 384 CIP-MSG8O2-3-RESOURCDEPLETED 394 CIP-LOADER-3-STREXE 384 CTP-MSG8O2-6-SHRINK_CONN 395 CIV-LOADER-3-SUNDERR 384 CIPMSG802-SHUT_IPROG 395 CIP-LOADER-3-SYMEXE 384 CIP-MSG802-6-START802jAILED 395 CIP-LOADER-3-SYRERR 385 CIP-MSG802-3-UNKNOWNE VENT 395 CIP-LOADER-3-TSHSIZ 385 CIP-MSG8O2-3-UNSUPPORTED 396
CIP-LOADER-3-TYPERR 385 CIP-NEYADAM-BADADD 397
CIP-LOADER-3-.USRERR 385 CIP-NEVADA-0-BADDISABLE 397
CIP-LOADER-3-VARI-IIP 385 CIP.-NEVADAM-BADENABLE 397
CIP-LOADER-3-VARLOP 385 CJP.-NEVADA-0-IBADENABLE2 398
CIP-LOVE-3-LOVELETTER 386 CIP-NEVADA--0-BADINT 398
CIP-MBUF-O-MFREEx2 386 CIP-NEVADA-0-BADREMOVE 398 CTP-MBUF-0-PANIC 386 CIP-OFFL-6-COMMAND 399
CIP-MEMD-3-BADIPC 387 CIP-OFFL.-3-HEX16B 399
CIP-MEMD-3-BADPTR 387 CIP-OFFL-3HEX4W 399
CIP-MEMD-3-BADVCN 387 CIP-OFFL-3-ILLALD 400
CIP-MEMD-.3--VCNDEREGISTER 388 CIP-OFFL3-ILLALH 400
CIP-MEMD-3-VCNREGISTER 388 CIP-OFFL-3-ILLEN 400 CIP-MS6802-3-ADAPTER_L1MITEXCEED 388 CIP-OFFL-0-ILLFREEI 400 CIP-MS0802-6-ADAPTER_OPEN 389 CIP-OFFL-0--ILLFREE2 401 CIP-MSG8O2-6-ADAPTER_REM 389 CIP-OFFL-0-IL 401 CIP-MSG8O2-6-ADAPTER_UPD 389 CIP-OFFL-3-ILLRST 401 CIP-MSG8O2-6-CTASET_FAIL 389 CIP-OFFL-6-LONGREC 401 CIP-MSG8O2-6-FRAMESZ_EXCEEDED 390 CIP-OFFL-3MISRST 402 CIP-MSG802-3HARD_ERROR 390 CTP-OFFL-6-MSGLEFT 402 CIP.-MS0802-3-JNVALID_CF3CMD 390 CIP-OFFL-0-NOMBUF 402 CIP-MSG8O2-6-INVALID_ID 390 CIP-OFFL-3-NOMEM 402 CIP-MSG8O2-3-INVALJD_MSICMD 391 CIP-OFFLM-NOPEND 403 CIP-MSG8O2-6-INVALIDPRIIVIITIVE 391 CIP-OFFL-6-NOTXBUF 403
CIP-MSG8O2-3-INYALID_VCN1 391 CTP-OFFL-i-PENDREQ 403 CIP-MSG80234NVALID_VCN2 391 CIP-OFFL-3.-REJSOCK 403 CIP-MSG8O2-6-LLC_DUPCCB 392 CIP-OFFL-i-REQFORM 404 CIP-MS0802-6-LLCDUP SAP 392 CIP-OFFL-3-REQLEN 404
Index CIP-OFFL-3-REQTYPE 404 CIIP-SYS-2-FREEBAD 415 CIP-OFFL-6-SOCREQ 404 CIP-SYS-2-FREEFREE 415 CIP-OFFL-6-UNEXP 405 CIP-SYS-3-INUSEFREE 415
CIP-OFFL-6-VIRTOFFL 405 CIP-SYS-3-llTVMEMINT 415
CIP-OFFL-6-WRCHAIN 405 CIP-SYS-2-LOWMEM 416
CIP-OFFL-0-WRONGFREE 405 CIP-SYS-2-MEMTOOSMALL 416 CIP-OFFL-3-WRONGLINK 406 CIP-SYSMGT_RPC-3-BRROR 418 CIP-SCB-6-BADSCB 406 CIP-SYSMGT_RPC-3-IPC_ERROR 418 CI-6-PSCHANGE 62 CIP-SYSMGT_RPC-6-STATE_CHANGE 418 CIP-SCHED-0-BADPRIORITY 406 CIP-SYS-6-MTRACE 416
CIP-SCHED-0-INVLOCK1 407 CIP-SYS-2-NOMEMFRG 416
CIP-SCHED-0-INVLOCK2 407 CIP-SYS-2-NOMEMORY 417
CIP-SCHED-0-NMLDATA 407 CIP-SYS-3-NZREFCNT 417 CIP-SCHED-0-NOLOCK 407 CIP-SYS-3-OVERRUN 417
CIP-SCHED-0-NOPROCID 408 CIP-SYS-5-RELOAD 417 CIP-SCHED-0-NOSTACK 408 CIP-SYS-5-RESTART 417
CIP-SCHED-0-NOTCB 408 CIP-SYS-3-WRONGFREELTST 418
CIP-SCHED-0-NOTMYLOCK 408 CIP-TCPIP-0-PANIC 419 CIP-SCHED-0-NOTPROCES 409 CIP-TN3270S-4-BAD_MAX_LUS_CFG 419
CI-3-PSFAIL 62 CIP-TN3270S- 1-LISTENFAIL 419
CIP-SLC-3-PCANIVIIRESET 409 CIP-TN3270S- 1-NQBIND_REQ_RCVD 420 CIP-SLC-3-SCANEP1 409 CIP-TN3270S- i-NO_DYN_ACTLU_REQ_RC 420 CIP-SLC-3-SCANEP2 410 CIP-TN3270S- 1-NO_EVENT_BUFS 421 CIP-SLC-3-SCANSLC 410 CJP-TN3270S- 1-NO_LU_MEMORY 421 CIP-SLC-3-STOPBIDITO 410 CIP-TN3270S-4-NQLU_SESSIONS 422 CIP-SLC-3-STOPEPTO 410 CIP-TN3270S- 1-NO_NTFY_AV_RSP_RCVD 422 CIP-SS1802-6-DUMP 411 CIP-TN3270S- 1-NQNTFY_UA_RSP_RCVD 423 CIP-SS1802-3-FATAL_ERROR 411 CIP-TN3270S- 1-NO_PSID_RSP_RCVD 423 CIP-SS1802-3-RTN_ADR 411 CIP-TN3270S- -NQSDT_REQ_RCVD 424 CIP-SUBSYS-2-BADCLASS 412 CIP-TN3 27 OS- 1-NO_S DT_TMARK_RCVD 424 CIP-SUBSYS-2-BADSEQUENCE 412 CIP-TN3270S- 1-NOJJNBIND_RSP_RCVD 425 CIP-SUBSYS-2-BAD VERSION 412 CIP-TN3270S- 1-NO_UNBIND_TMARK_RCVD 425 CIP-SUB SYS-2-MAXRECUR 412 CIP-TN3270S- 1-RP_PU_CONFLICT 426 CIP-SUB SYS-2-MISMATCH 413 CTP-TN3270S- 1-START_FAIL 426 CIP-SUBSYS-2-NOTFOUND 413 CIP-TN3270S-6-START_OK 426 CIP-SYS-3-BADBLOCK 413 CIP-TN3270S-6-STOPPING 427 CIP-SYS-3-BADFREEMAGIC 413 CIP-TN3270S-0-TELNETINITFAIL 427
CIP-SYS-3-BADFREEPTRS 414 CI-3-SLOTCOMP 63
CIP-SYS-3-BADMAGIC 414 CLEAR-S-COUNTERS 63
CJP-SYS-2-BADSHARE 414 CLNS-5-ADJCHANGE 63 CIP-SYS-6-BLKINFO 414 CLNS-4-AREALOST 64
System Error Messages CLNS-4-BADPACKET 64 CONTROLLER-3-UPDOWN 75
CLNS -BKUPERR 64 CSC2.-4-BREAK 75 CLNS-4-CKSUMERR 64
CLNS-4EDATFAIL 65
CLNS-4-EEST-IFATL 65
CLNS-LLINKERR 65 CLNS-3-LSPCHAIN 65 DBUS-3-BADCTRLRTYPE 75 CLNS-4-LSPCKISUM 66 DBUS-3-BADEEPROM 76 CLNS-3-LSPDB 66 DBUS-i-BADHSACONF 76 CLNS-4-LSPFULL 67 DBUS-3-CXBUSERR 77 CLNS-3-LSPIXARRMATCH 67 DBUS-3-DAUUHTER_STATS 76 CLNS-3--LSPIXARRNULL 67 DBUS-3-DBUSThTTERR 76 CLNS-3-LSPIXHEAD 67 DBUS-3-DBUSTIMOUT 77 CLNS-4-LSPTOOBIG 67 DBUS-3-NOMAC 77 CLNS3-NSAPES 68 DBUS-3-NOMAGJC 77 CLNS-4-NSAPIS 68 DBUS-3-NORESP 78 CLNS-3-ONLIST 68 DBUS-3-SLOTCOMP 78 CLNS-4-REDIRECT 68 DBUS-3-SW_NOTRDY 78 CLNS-4-TENT 68 DBUS-3-UNKNOWN 79 CLS-3-CLSFAIL 69 DBUS-3-WCSCTRLRERR 79 CLSDR-3-ERRRTN 69 DBUS.-3--WCSERR 79 CLSDR-1-INCORRECTPORT 69 DBUS-3-WCSFLOW 80 CLSDR-3-MSGERR 70 DBUS-3-WCSLDERR 80 CLSDR-3-NOCEP 70 DBUS-3-WCSPARERR 80 CLSDR-3-NOCLSSERVER 70 DBUS-3-XILJNX 80 CLSDR.1-NODLUCREATE 70 DIALER-2-NOMEMORY 81 CLSDR-.3--NOINIT 71 DIALER-2-JIOSWIDB 81 CLSDR3--NOPORTCREATE 71 DIRRESP-7-NOROUTE 81 CLSDR-3-NOREMOVECEP 71 DIRRESP-3-SUBNETTED 82 CLSDR-3-NOREMOVEPORT 71 DLC-3-BADPARAM 82 CLSDR-3-WRONGMSG 72 DLC3ANVPCEP 82 COMP-i-CONFIGBAD 72 DLC-3-NOMEMORY 82 COMP-5-NOBTJF 72 DLC.-4-OPTNIJLL 83 COMP3-NOMEMORY 73 DLC-3-WPUTERR 83 COMP-3-SIZEBAD 73 DLSWC-3-BADCLSI 84 COMP-3-SYNCBAD 73 DLSWC-3-BADCLSTCNF 84 COMP-3-VERSIONBAD 73 DLSWC-3-BADCLSIDATALEN 84 CONTROLLER-2-CRASHED 74 DLSWC-3-BADCLSIHDRLEN 84 CONTROLLER-2-FIRM WARE 74 DLSWC-3-BADCLSIIDTYPE 84 CONTROLLER-2NOTFOUND 74 DLSWC-3-BADCLSIIND 84 CONTROLLER-3-REMLOOP 74
Index DLSWC-3-BADCLSIPRIMTYPE 84 DRP-7-NOROUTE 92
DLSWC-3-BADCLSIRET 84 DRP-3-NO WRITE 92
DLSWC-3-BADCLSISAP 84 DRP-3-SUBNETTED 93
DLSWC-3-BADDLCOP 84 DSPU-3-ActpuNegResporise 93 DLSWC-3-BADPEEROP 84 DSPU-3-CLSIBadAdptC0LT 93 DLS WC-3-BADSSPE VENT 84 DSPU-3-CLSlBadldentifier 93
DLSWC-3-BADSSPHDR 84 DSPU-3-CLSlBadldentifierType 94
DLSWC-3-BADSSPOP 85 DSPU-3-CLSlBadLength 94 DLSWC-3-BADTIMEROP 85 DSPU-3-CLSlBadPrimitiveCrnd 94
DLSWC-3-FAILASSERT 85 DSPU-3-CLSIB adPrimitiveType 94 DLSWC-3-FORKFATL 85 DSPU-3-CLSIB adRetumnCode 94
DLSWC-3-FSMACTION 86 DSPU-3-CLSlUnexpctActSapCnf 95 DLSWC-3-FSMCALL 86 DSPU-3-CLSlUnexpctDeactSapCnf 95 DLSWC-3-FSMERR 86 DSPU-3-CLSlUnexpctEnableCnf 95
DLSWC-3-FSMINTERR 86 DSPU-3-CLSlUnexpctldStrilnd 95
DLSWC-3-FSMUNKERR 86 DSPU-3-DSPU_BufferConiipted 96 DLSWC-3-INVALIDSTATE 86 DSPU-3-LSConnlnFailed 96
DLSWC-3-TNVALIDTIMER 86 DSPU-3-LSConnlnFailedNoMein 96
DLSWC-3-NOBUFF 86 DSPU-3-LSConnlnFromHostFailed 96
DLSWC-3-NODLSW 86 DSPU-3-LSConnlnFromPuFailed 97
DLSWC-3-NOMEMBACK 86 DSPU-3-LSConnOutToHostFailed 97
DLSWC-3-NOMEMDLC 87 DSPU-3-LSConnOutToPuFailed 97
DLSWC-3-NOMEMSSP 87 DSPU-3-LSlnvalidMaxlFrame 97
DLSWC-3-NOPARAM 87 DSPU-3-LSlnvalidWindowsize 98
DLSWC-3-NOPEER 87 DSPU-3-LSNoACTPUCapabiIity 98 DLSWC-3-RECVSSP 87 DSPU-3-LSXlDNegotiationError 98 DLSWC-3-SENDSSP 87 DSPU-3-NotifyNegRsp 99 DLSWP-3-PBADVALIJE 88 DSPU-3-SnaBadData 99
DLSWP-3-PCAPMISMATCH 88 DSPU-3-UnknownXid 99 DLSWP-3-PGENERAL 88 DSXI -3-BADENCAP 100
DLSWP-3-PNOMEM 88 DSXJ-1-NOMEMORY 100
DLSWP-3-PPASSIVE 89 DUAL-3-ANCHORCOUNT 100
DLSWP-3-PPRIVIISMATCH 89 DIJAL-3-BADCOUNT 101
DMA-I -BADJCBPTR 89 DUAL-3-BADSUMNOTIFY 101
DMA-i -BADJUMPSTART 90 DUAL-6-EVENT 101
DMA-i -BADLENGTH 90 DUAL-3-INTERNAL 101
DMA-1-BADOWN 90 DUAL-3-LINKSEXIST 102
DNET-3-HEARS ELF 91 DUAL-3-LJNKSTJLLUP 102
DNET-4-MAPCON 91 DUAL-3-MULTIFLOW 102
DNET-3-NOMEMORY 91 DUAL-S-NB RCHANGE 102
DNSIX-3-NOBUFFER 92 DUAL-3-NOBUFFER 103
10 System Error Messages DUAL-3-NOHANDLE 103 FDDI-3-FDDIRSBTU 112
DUAL-3-NOMATCH 103 FDDI-3-NOCAM 112
DUAL-3-NOMEMORY 103 FDDI- -NOMEMORY 112
DUAL-3-NOSOCKET 104 FDDISTAT-4-STATUS 112 DUAL-3-PEERSEXIST 104 FILESYS-5-PCMCIAJNSERT 113 DUAL-3-PROBESEQ 104 FILESYS-5-PCMCIA REMOVE 113
DUAL-3-RDBLEFT 104 FLASH-3-ACCESSATTRIBONRP 113
DUAL-3-REFCOUNT 105 FLASH-3-ERASEFAIL 114 DUAL-3-SIA 105 FLASH-3-WRITEFAIL 114
DUAL-3-SIANOHANDLE 105 FR-5-DLCICHANGE 114
DUAL-3-UNKTIMER 105 FR-4-MAPERROR 114
DVMRP-1-BADMASK 106
DVMRP- -ROUTEHOG 106
GRIP-3-BADPATHS 115
GRIP-2-BADROUTE 115
EGP-3-NOPDB 106
EGP-3-TOOBTG 107
ENV-2-FLOW 107
ENVIyI-2-FAN 108 ENVM-2-FANOK 108 HD-1-BADENCAP 115 ENVM-1-SHUTDOWN 109 HD-3-BADENCAP 115 ENVM-2-SUPPLY 109 HD- -B ADLOOPCABLB 116 ENVM-2-TEMP 109 HD-1-BADPORT 116 ENVM-2-VOLTAGE 109 HD- -BADPORTADAPTER 116 ENV-1-SHUTDOWN 107 HD-1-BADRING 115 ENV-2-TEMP 107 HD-0-INITFAIL 116 ENV-2-VOLTAGE 108 HD-1-INITFAIL 116 ETHERNET-i -NOMEMORY 110 HD-5-LINEFLAP 116 ETHERNET-1-TXERR 110 RD-1-MEMERR 117
HD-1-NOMEMOR 117
HD-0-NOMEMORY 117 HD-3-ODDSTART 117
HD-3-OUTENCAP 117
FDDI-3-BADMUL 110 HD-3-OWNERR 118
FDDI-3-BADSLOT 111 HUB-1-BADHUB 118
FDDI-3-FDDIFAIL 111 HUB-1-BADUNIT 118
FDDI-3-FDDIFAIL2 111
FDDI-3-FDDIRSET 111
Index 11 HUB-1-NOMEMORY 118 IPFAST-6-IN VALIDATE 129 HUB-1-READERR 119 IPFAST-6-INVALREQ 129
HUB-1-WRITEERR 119 IPFAST-4-RADIXDELETE 129
IPFAST-2-RADIXINIT 130
IPFAST-4-RADIXINSERT 130
IPFAST-3-SANITY 130 IP-3-LOOPPAK 122 IPRT-3-BADCOMLIST 131 1BM2692 -1-ADP_CHK 119 IPRT-2-COMPRESS 131 1BM2692-1-ICDBPERROR 119 IPRT-3-NOMEMORY 131 IBM2 692-1 -INITFAIL 120 IPRT-3-PATIIIDX 131 IBM2 692-1 -NOPCIMEMORY 120 IPRT-3-TOOMANYNETS 132 1BM2692- -NOSYSMEMORY 120 IP-5-WEBINSTCOMP 123 1BM2692-1 -PCI PERROR 120 IP-5-WEBINSTJCILL 123 IBM2 692-1 -RX_HALT 120 IP-5-WIEBINSTRESP 123 IGRP-3-NOSOCKET 121 IP-5-WEBINSTLSTART 123 IP-3-BADIPALIGN 121 IPX-3-BADCOUNT 132 IP-3-BADSROUTE 121 IPX-3-BADIGRPSAP 132 IPC_RSP_CBUS-3-CARDERR 126 IPX-3-BADIGRPSAPTYPE 133 IPC_RSP_CBUS-3-INVNUM 127 IPX-3-BADPATHS 133 IPC_RSP_CBUS-3-MSGERR 127 IPX-3-NOMEMORY 133 IPC_RSP_CBUS-3-NOBUF 127 ISDN-6-CONNECT 134 IPC_RSP_CBUS-3-NOHWQ 127 ISDN-6-DISCONNECT 134 IPC_RSP_CBUS-3-PROC 128 IPC_RSP_CBUS-3-SEATERR 128 IPC-2-CANT_SEND 124
IPC-2-CONSISTENCY 124
IPC-2-DELETED 124 IP-4-CLASS 122 LANCE-4-BABBLE 134
IPC-2LOCK 124 LANCE-3-BADENCAP 135
IPC-2-NOBUFFER 125 LANCE-3-BADUNIT 135
IPC-5-NODELFUINC 125 LANCE-5-COLL 135
IPC-2-NODISPATCH 125 LANCE- 1-INITFAIL 135
IPC-2-NOMEM 125 LANCE-5-LATECOLL 136 IPC-2-ONINT 126 LANCE-5-LOSTCARR 136
TPC-5-SLAVELOG 126 LANCE- 1-MEMERR 136
JPC-2-UNLOCK 126 LANCE- 1-NOMEMORY 136
JP-3-DESTHOST 122 LANCE-3-OWNERR 136
IP-4-DUPADDR 122 LANCE-3-SPURIDON 137
IPFAST-2-BADIF 128 LANCE-3-UNDERFLO 137
IPFAST-7-INTLEV 129 LANE-3-BADILMI 137
12 System Error Messages LANE-3-J3ADNAME 137 LANMGR-4-BADRNGN1JM 149
LANE-3-BADTYPE 138 LANMGR-4-BADUPCALL 149 LANE-3-LANE_LESBUS_UP 138 LANMGR-4-OLDTRAMON 149 LANE-3-LANE_SIG_CHATN 138 LAPB-4-CTRLBAD 150 LANE-3-LANE_SIG_ERR 139 LAPB-4-FRAMEERR 150 LANE-3-LANE_S TO_IN V_MS 139 LAPB-4-INFOBAD 150 LANE-3-LANE_SIG_IN V_S TATE 139 LAPB-4-INVNR 151 LANE-6-LEC 139 LAPB-2.-NOBUF 151
LANE-.3-LEC_BADAD 140 LAPB-3-NOTNPIDB 151 LANE-3-LEC_CFG 140 LAPB-4-N1TOOBIG 151
LANE-3-LEC_CONTROL_MSG 140 LAPB-3-NULLPAK 151 LANE-3-LEC_ERR 140 LAT-3-BADDATA 152 LANE-6-LEC_INFO 141 LAT-3-BUFFULL 152 LANE-3-LEC_JOIN 141 LAT-3-NOSYNC 152 LANTh3-LEC_LIS TEN 141 LAT-3-NULLIDB 152 LANE-3-LEC_STGNAL 141 LAT-3-QBSPACED 152 LANE-4-LEC_STATE_ERROR 141 LAT-3-REIJSE 152 LANE-6-LEC_TIMER 142 LEX-3-NOTSENT 153 LANE-3-LECS_ERR 142 LEX-3-RCMDNAK 153 LANE-4-LECS_WARN 142 LEX-3-RCMDREJ 154 LANE-3-LSV_ADDR 143 LEX-3-TTMEOUT 154 LANE-3-LSV_BADAD 143 LINEPROTO-5-UPDOWN 154 LANE-3-LS V_CRASH 143 LTNK-3-BADENCAP 155 LANE-3-LSV_DUPATM 144 LTNK3-BADETHER 155 LAN3-LSV_DUPTD 144 LINK-3-BADMACREG 155
LANE-3-LSV_DUPMAC 144 LINK-2-EADVCALL 156 LANE-4-LSV_LECID 145 LINK-3-BOGUSENCAP 156 LANE-3-LSV_MCAST 145 LINK-5-BOOTP 156 LANE-3-LSV_NOREG 145 LTNK-4-I3RIDGECONFLICT 156 LANE-6-MAKE17 145 LINK-S-CHANGED 157
LANE-3-NAMECHG 146 LINK-3-COMPREG 157 LANE-3-NEWPREF 146 LINK-4-FDDISTAT 157
LANE-3-NOTLMI 146 LINK-4-FDDIUNK 157
LANE-3-NOINT 146 LINK-2-LINEST 158
LANE-3-NOREGATM 147 LTNK.-4-NOMAC 158 LANE-3-NOYCD 147 LINK-2-NOSOURCE 158
LANE-3-PVCBAD 147 LINK- -RARP 158
LANE-3-PVCLECS 148 LTNK-3-REMLOOP 159
LANE-3-REGSTATE 148 LTNK-5--SLARP 159 LANE-3-TYPECHG 148 LINK-3-TOOBIG 158 LANE-5-UPDOWN 148 LTNK-3-TOOSMALL 158
Index 13 LINK-2-UENCAP 158 MCI-5-INPUTERR 166 LINK-3-UPDOWN 159 MCI-4-NOCOOKJE 167
LLC-4-T1ERR 159 MCI-4-NOKEEPALIVE 167
LLC-2-UNEXPECT 160 MCI-S-OBSOLETE 167
LNMC-3-BADCLSI 160 MCI-4-RSETFAIL 167
LNMC-3-BADCLSICNF 160 MCI-3-RXINDEX 168
LNMC-3-BADCLSTDATALEN 160 MCI-3-SETUPERR 168
LNMC-3-BADCLSIHDRLEN 160 MCI-4-TESTFAIL 168
LNMC-3-BADCLSIIDTYPE 160 MKS-3-BADENCAP 169
LNMC-3-BADCLSIIND 160 MKS-3-BADRING 169
LNMC-3-BADCLSIPRIMTYPE 160 MKS-3-BADUNIT 115 169
LNMC-3-BADCLSIRET 160 MKS-0-INITFAIL 169
LNMC-3-BADCLSISAP 160 MKS- -INIITNOPPRIM 169
Local Timeout control reg Error address at MKS-0-INTTUERR 169 PC 432 MKS-S-LINBFLAP 169 LPD-3-MANYLF 161 MKS-1-MEMERR 170
MKS-0-NOMEMORY 170
MKS-3-ODDSTART 170
MKS-3-OUTENCAP 170
MKS-3-OWNERR 170
MKS-3-PLOSTERR 171 MAILBOX-3-BADCHKSUM 162 MKS-3-PPRIMERR 171 MAILBOX-3-BADDATA 163 MKS-3-SPURPPRIMERR 171 MAILBOX-3-BADECHO 163 MKS-3-UPRIMERR 171 MAILBOX-.3-BADPDU 164 M32- 1-NOMEMORY 162 MAILBOX-3-FLAGSTAT 163 MROUTE-4-RADIXDELETE 171 MAILB OX-3-TNITFAIL 164 MROUTE-2-RADIXINIT 171 MAILB OX-6-INITOK 164 MROUTE-4-RADIXINSERT 172 MAILBOX-3-INITPC2 163 Multibus Timeout control reg Error address MAILBOX-3-INTERR 163 at PC 433 MAILBOX-3-MAILO2O 163
MAILBOX-3-MAILFAIL 163
MAILBOX-7-MBOXDEBUG 164
MAILBOX-3-NOECHO 165
MAILBOX-3-OFFLINE 165
MAILBOX-7-ONLINE 165 NETMGT-6-ALERT 172
MAILBOX-3-PC2 163 NHRP-3-NOBUFFER 172
MAILBOX-7-READ 166 NIM-2-BADNIMREV 173
MAILBOX-3-SPURINT 163 NTM-2-BADSLOT 173
MAILBOX-3-TIMEOUT 166 NTM-2-BADSIJBUNIT 173 MAILBOX-7-WRITE 166 NIM-2-DEADCHAINQ 173
14 System Error Messages NIM-2-DEADICHAINQ 173 PAD-3-GETLINE 182 NIM2-LOSTCHAINQ 173 PAD-2.-INTR 182 NTM-2-LOSTICHAINQ 174 PAD-2-PUTSETUP 182
NIM-2--NOHWADDRESS 173 Parity control reg Error address at NIM-2-UNSUPNIM 174 PC 433 PARS ER4-ADRANGE 183
PARSER-4-BADCFG 183
PARSER-3-BADSUIBCMD 184 PARSER-3-CREAThJNT 184 PARSER.2-INTDIS4BLE 184 OIR-6-INSCARD 174 PARSER-4-INVLDLINE 184 OIR3-LONGSTALL 175 PARSER..4-INVLDNVcIJEN 185 OIR-6-NOEOTR 175 PARSER-4-LINKPOINT 184 OJR-6-REMCARD 175 PARSER-4-MULFUNCS 184 OSPF-4-BADLENGTH 176 PARSER-4-MULTIPLEIFS 184 OSPF-4-BADLSATYPE 176 PARS ER-3-NOLINK 184 OSPF-4-CONFLICTING_LSAID 176 PARS ER-3-NOMEMORY 185 OSPF-4-ERRRCV 177 PARS ER.-4-NUMHELP 184 OSPF-3-INTERNALERR 177 PARSER-4-NVGEN 184 OSPF-3-NOBACKBONE 177 PARSER-4-PROTOADDR 184 OSPF-3-NOCONNDB 177 PA-2-UNDEFPA 182 OSPF3-NOLSA 178 PA-2-UNDEFPABRIDGE 182 OSPF3-NOMEMORY 178 PCBUS-3-BADENCAP 186 OSPF-4-NONEIGHBOR 178 PCBIJS- -MOMEMORY 186 OSPF-4-NORTRTD 178 PIM- -INVALID_RPJOIN 186 OSPF-6-NOSRCPDB 179 PIM- -INVALID_RP_REG 187 OSPF-4-NOTREDIST4 179 PPP-4-CONFNAK 187 OSPF-4-NOTREDISTS 180 PPP-4-IPXNET 187 OSPF-6-NOTREDIST1 179 PPP-6-LOOPED 188 OSPF-6--NOTREDIST3 179 PPP-4-NOEXYFACACS 188 OSPF-4-OSPFINTDOWN 180
OSPF-3-UNKNOWNSTATE 180 OSPF-4-VIRTUAL_IN_NON_BACKBONE 180
QA-3-ALLOC 188 QLLC-3-BADSUBADDRESS 190 QLLC-3-BADOPCODE 189 PA-2-BADIDB 181 QLLC-3-BADQLLCSTATE 189 PA-2-BADINTERFACE 181 QLLC-3-BADRSRBOPCODE 189 PA-1-BADPABAY 181 QLLC-3-BADSTATE 189 PA-2-BADPASCB 181
Index 15 QLLC-3-BADSTATEEVENT 190 QLLC-3-DIFFPRTR 190 QLLC-3-GENERRMSG 190 RADIX-3-ADDMASK 199 QLLC-3-IFRAME 191 RADIIX-3-BADTREE 199 191 QLLC-3-INCALL_CFG RADJX-3-DELETE 199 191 QLLC.-3-LNXNOTFOUND RAD 200 QLLC-3-NO_QLLCBUFFER 193 RADIX-2-NOMAXKEYLEN 200 QLLC-3-NO_QSR 193 RADIX-3-NOMEMORY 200 193 QLLC-3-NO_RESOURCE RADIX-4-ORPHAN 200 QLLC-3-NOLLC2 191 RCMD-4-INVALDHOST 201 QLLC-3-NOMACADDR 192 RCMD-4-NOMEMORY 201 QLLC-3-NOMEM 192 RCMD-4-NORSHPROC 201 QLLC-3-NONULLXID 192 RCMD-4-RCMDDNS FAIL 201 QLLC-3-NOPAKENQ 192 RCMD-4-RCPATTEMPTED 202 QLLC-4-NOQLLC 192 RCMD-4-RSHATTEMPTBD 202 QLLC-3-NOX1D2 193 RCMD-4-RSHPORTATTEMPT 202 QLLC-3-NULLPTR 194 REGEXP-2-BADLIST 202 QLLC-3-QLLCMAP ERR 194 RIP-3-NOSOCKET 203 195 QUICC_ETHER-5-COLL RSP-3-AIPPANIC 203 QUICC_ETHER-5-HB EAT 195 RSP-3-BADHWREV 203 QUICC_ETHER- -INITFAIL 195 RSP-4-COOKIE 204 QUICCBTHER-5-LATECOLL 195 RSP-3-ERROR 204 1-LOS TCARR 196 QUICC_ETHER- RSP-3-FLASH 204 196 QUICC_ETHER-3-UNDERFLO RSP-3-FOREVER 204 QUICC_SBRJAL-3-CTSLOST 197 RSP-3-IDPROM 205 QUICC_SBRIAL -INITFAIL 198 RSP-3-INVRTN 205 QUICC_SBRIAL-5-LINEFLAP 198 RSP-3-INVRTNBCASTID 205 QUICC_SERTAL-3-UNDERFLO 198 RSP-3-IPC 205 QUICC-3-BADUNIT 194 RSP-3-LOVBGIANT 206 QUICC-5-COLL 194 RSP-3-LOVBNOTE 206 QUICC-5-HBEAT 196 RSP-3-MSDOG 206 196 QUICC-5-LATECOLL RSP-3-MSFIX 207 197 QUICC-5-LOSTCARR RSP-3-MSVERS 208 QUICC-1-NOMEMORY 197 RSP-3-NOLOVE 208 QUICC-3-OWNERR 197 RSP-3-NOMAC 208 QUICC-3-UNDERFLO 199 RSP-2-NOMEMORY 209 RSP-3-NORESTART 209
RSP-3-NOSTART 209 RSP-2-QAERROR 209
RSP-3-RESTART 210
16 System Error Messages RSP-3-RESTARTREQ 210 SCHED-3-PAGBZERO 221 RSP-3-SLAVECHANGE 210 SCIED-3-PRTORITY 222 RSP-3-SLAVEMASTER 212 SCHED-2QUEUENOTEMPTY 222 RSP-3-SLAVEROM 212 SCHED-2-SEMUNLOCK 222 RSP-5-SLAVEUP 212 SCHED-3-STACKSIZE 222 RSP-2-STALL 212 SCHED-3-STILLWATCHING 222 RSP-3-XBUFHDR 213 SCHED-3-STILLWATCWNGT 222
RSRB-4-BADLEN 213 SCHED-3-STUCKMTMR 222
RSRB-4-BADLENIP 213 SCHEDJSTUCKTMR 223 RSRB-3-BADVERSIONIFST 213 SCHED-3-THRASHING 223 RSRB-3-BADVERSIONIF 213 SCHED-3-UNEXPECTEDEVENT 223
RSRB-3-BADVERSIONTCP 214 SCHED-3-UNBXPECTEDMESSAGE 223 RSRB-4-BADVRE 214 SCHED-3-.UNIEXPECTBDQUEUE 223 RSRB-4-CONIPST 214 SCHBD-3-UNEXPECTEDTIMER 223 RSRB-4-CONNILLSTATE 214 SCHED-2--WATCH 223
RSRB-4-CONNSTAT 214 SCHED-2-WATCHTIMER 223 RSRB-3-FSTBRR 214 SDLC-6-BADFRAME 224
RSRB-3-HDRNOVRP 215 SDLC-5-CONFIGERR 224 RSRB-4-HDRRECV 215 SDLC-4-CTRLBAD 224
RSRB-3-HDRVRP 215 SDLC-3-DLU_ERROR 224
RSRB-3-IFERR 215 SDLC-4-DROPPED 225
RSRB-4-ILLPEER 215 SDLC-4-FRAMEERR 225
RSRB-4--LOCAL 215 SDLC-2-ILLEGSTATE 225
RSRB-3-NOMEMORY 216 SDLC-4-INFOBAD 225
RSRB-3-NOTREM 216 SDLC-5-INVLDGRPCFG 226 RSRB-4-OPTNULL 216 SDLC-4-INVLDGRPPOLL 226 RSRB-4-PEERSTAT 216 SDLC-5--INVLDORPPOLL 226
RSRB-4-RNGXFAIL 216 SDLC-4-INVNR 225 RSRB-3--SENDPUNTFST 216 SDLC-2-NOBUF 227
RSRB-3-SENDPUNTIF 216 SDLC-4-NOFRMRSPACE 227
SDLC-3-NOINPIDB 227
SDLC-2-NOPOINTER 227
SDLC-4-NOUA 228 SDLC-4-N TOOBIG 226 SDLC-.i-NIJLLPAK 228 SCHED-2-ATTRCMD 221 SDLC-4-SDLCjIRR 228 SCHED-2-ATTRVALUB 221 SDLC-4JJNKNOWNADDR 228 SCHED-2-EDISMSCRIT 221 SDLC-4-WRONGADDR 229 SCHED-3-LOSTWAKEUP 221 SDLC6-XIDDISPLAY 229 SCHED-2-NOATTR 221 SDLC-6-XIDfORMAT 229 SCHED-2 -NOT WATCHTIMER 221 SDLC-4-XID_NOMATCH 229
Lndex 17 SDLLC-5-ACT LINK 230 SMRP-5-NEIGHBORDOWN 239 SDLLC-5-DACT_LINK 230 SMRP-6-NEIGHBORUP 239 SDLLC-6-XID DISPLAY 230 SMRP-3-NOFDDICOMPAT 239 SDLLC-6-XID_FORMAT 231 SMRP-5-PORTDOWN 239 SDLLC-4-XID_NOMATCH 231 SMRP-6-PORTUP 239 SEC-6-IPACCESSLOGDP 231 SNAPSHOT-2-BADSTATE 240
SEC-6-TPACCESSLOGNP 232 SNAPSHOT-2-NOMEMORY 240 SEC-6-IPACCESSLOGP 232 SNAPSHOT-2-TOOMANYDIALERS 240 SEC-3-NOMAX 232 SNMP-4-NOTRAPIP 241 SEC-2-NOOPT 232 SNMP-3-SOCKET 241 SEC-2-NOTSEC 232 SSE-3-BADMEMORY 242 SEC-2-SECINS 232 SSE-1-BOGUSEQ 242 SEC-4-TOOMANY 232 SSE-2-BOGUSEQ 242 SERVICE_MODULE-4-ACCESSERROR 233 SSE-6-COMPERR 242 SERVICE MODULE-4-ALARMFATLURE 233 SSE-2-HUNG 243 SERVICE_MODULE-4-BADTYPE 233 SSE-2-HWFAILURE 243 SERVICE_MODULE-4-COMMANDFAILED 234 SSE-2-MEMERROR 243 SERVICE_MODULE-0-llTITFAILURE 234 SSE-1-NESTADDR 243 SERVICEMODULE-4-INTERBYTETIMEOUT 234 SSE-2-NESTADDR 244 SERVTCE_MODULE-3-LOOPDOWNFAILED 234 SSE-1-NOMATCH 244 SERVTCE_MODULE-5-LOOPDOWNREMOTE 235 SSE-2-NOMATCH 244 SERVICE_MODULE-5-LOOPUPPAILED 235 SSE-3-NOMEMORY 244 SERVICE_MODULE-5-LOOPUPREMOTE 235 SSE-2-NOTZERO 245 SERVICE_MODULE-4-NOTREADY 235 SSE-2-SWFAILURE 245 SERVICE_MODULE-4-OLDIMAGE 236 54T68360-1-DISCOVER 217 SERVICE_MODULE-4-REPEATEDRESET 236 S4T68360-l-DWNLDCKSM 217 SERVICE_MODULE-4-REQUESTOVERLOAD 236 S4T68360-1-DWNLDFL 217 SERVICE_MODULE-S-RESET 236 S4T68360-1-INITFAIL 218
SERVICE_MODULE-4-RESETFAILUIRE 237 S4T68360-3-MBXREAD 218 SERVICE_MODULE-4-UNKNOWNALARM 237 S4T68360-1-NOTCMPLT 218
Shared Memory Parity Error shared memory control S4T68360-l-NOTREADY 218 register error caused by slot access S4T68360-3-N0TS4T68360 219
in bytes lldec 433 54T68360-3-OWNERR 219
Shared Memory Parity Error shared memory control S4T683603-PANIC 219
register error caused by MPU access in S4T68360- -STARTFAIL 219 bytes 433 S4T68360- -STOPFA1IL 220 SLIP-2-BADQUOTE 237 54T68360-3-TOOSMALL 220
SLIP-2-BADSTATE 237 STANDBY-3-BADAUTH 245 SMP-3-NO_MEM 238 STANDBY-3-MISCONFIG 246 SMRP-2-ASSERTFAILED 238 STANDBY-3-NOBUFFER 246
SMRP-7-DEBUGMSG 238 STANDBY-3-NOMEMORY 246
18 System Error Messages STANDBY-3-NOSOCKET 246 SYS-2-BADPOOLMAGIC 254
STUN-3-BADCONN 247 SYS-ThBADPRTNT 255
STUN-3-BADLENOP 247 SYS-3-BADPROCESS 255
STUN-3-BADMAGIC 247 SYS-3-BADRESID 255 STUN-3-BADMAGICTCP 247 SYS-2-BADSHARE 254 STUN-3-BADPASSIVEOPEN 247 SYS-2-BADSTACK 254
STUN-3-CONNILLSTATE 247 SYS-6-BLKJNFO 254
STUN-6-CONNOPENFAIL 247 SYS-2-BLOCKHIJNG 255
STUN-6-ERR 248 SYS-2-CFORKLEV 254 256 STUN-2-NOBIJF 248 SYS-2-CFORKMEM 256 STUft3-NOINPIDB 248 SYS-2-CHUNKBOUNDS 256
STUN-3-.NOPROTMEM 248 SYS-2-CHUNKFREE 256 STUN-3-NOTGEM 249 SYS-2-CHUNKPARTIAL 257
STUN-2-NOTGI 249 SYS-2--CHUNKSIBL1NGS 257
STUN-6-OPENED 249 SYS-5-CONFIG 254 257 STUN-6-OPENING 249 SYS-2-CONFIGJJOWNFAIL 257 STUN-6-PASSIVEOPEN 249 SYS-5-CONFIG_I 257 STUN-6-PEERSHUTDOWN 249 SYS-5-CONFIG_L 257 STUN-4-PEERSTATE 250 SYS.-5--CONFIG_M 257 STUN-6-RECONNECT 250 SYS-4-CONFIG NEWER 258
STUN-3-SENDPUNT 250 SYS-5-CONFIG_NV 258 STUN-3-SENDPUNTTCP 250 SYS-3-CONFIG_NV_ERR 258 STUN6-TCPFINT 250 SYS-5-CONFIG_NV_M 258
STUN-6-TCPPEERSHUT 250 SYS-3-CPUHOG 258
SUBSYS-2-BADCLASS 251 SYS-3-DMPMEM 259 SUBSYS-2-BADSEQUENCE 251 SYS-4-DUAL_MESSAGE 259 SUBSYS-2-BAD VERSION 251 SYS-2-DIJPEXPORT 259
SUBSYS-2-MTSMATCI-J 251 SYS-2-.FREEBAD 260 SUBSYS2.-NOTFOUND 252 SYS-2-FREEFREE 260 SUBSYS-2-RECURSION 252 SYS-2-GETBUF 260
SYS-2-.ALREADYFREE 252 SYS-3.-HARJKARI 260
SYS-3-BADBLOCK 252 SYS-2-HEADER 260 SYS-2-BADBUFFER 253 SYS-2-INLIST 260
SYS-3-BADDISP 252 SYS-2-INLIST1 260
SYS-3-BADFREEPTRS 253 SYS-2-INPUTQ 260 SYS-3-BADLINKTYPE 253 SYS-2--INSCHED 260
SYS-2I3ADLIST 253 SYS-3-INTPRINT 261 SYS-3-BADMAGIC 254 SYS-2-INTSCHED 260 SYS-3-BADPARAM 254 SYS-3-INUSEFREE 260 SYS-2-BADPID 254 SYS4JN VALID JMAGE 261 SYS-2BADPOOL 254 SYS-3-INVMEMINT 261
Index 19 SYS-2-LINKED 262 SYS-.2-SELFLINKED 269
SYS-2-LOWMEM 262 SYS-2-SHARED 269
SYS-.2-MALLOCFATL 262 SYS-2-SHARED1 269 SYS-6-MEMDUMP 262 SYS-2-SMASHED 269
SYS-3-MGDTIMER 263 SYS-2-SMASHEDINPO 269 SYS1-MGDTIMEREXP 263 SYS-4-SNMP_HOSTCONFIGSET 270 SYSMGT_RPC-3-IPC_ERROR 274 SYS-4-SNMP_NETCONFIGSET 270 SYSMGT_RPC-3-NETMGT_EVENT 274 SYS-4-SNMP_WRITENET 270 SYSMGT_SNALLC.-3-E VENT_ERROR 274 SYS-2-SNMPOIDX 270 SYS-3-MSGLOST 263 SYS-3-SOCKUNKN 269
SYS-6-MTRACE 263 SYS-2-SPEC 269 SYS-2-NOBLOCK 264 SYS-6-STACKLOW 269
SYS-6-NOBRTDGE 264 SYS-3-SUPNONE 271 SYS-1-NOECO 264 SYS-2-SUPNOT 271
SYS-2-NOMEMFRG 264 SYS-2-SUPTWICE 271
SYS-2-NOMEMORY 265 SYS-5-TABLEERR 271
SYS-3-NOPROC 265 System failure error messages
SYS-2-NOPROCESS 265 Bus Error control register non-local memory
SYS-2-NOTDEAD 265 transaction timeout Bus Error address at SYS-2-NOTQ 265 PC 431
SYS-3-NULLIDB 265 Bus Error control register ram byte
SYS3-NZREFCNT 265 parity error Bus Error address at SYS-5-OUTSETUP 266 PC 432
SYS-3-OVERRUN 266 Bus Error control register system overtemp
SYS- -OVERTEMP 266 Bus Error address at PC 432 SYS-2-PAKCLIP 266 Local Timeout control reg Error address SYS-6-PROCINFO 267 at PC 432 SYS2-QCOUNT 267 Multibus Timeout control reg Error SYS-2-QINSERT 267 address at PC 433 SYS-3-REGARG 267 address Parity control reg Error at SYS-3-REGCREA2 267 PC 433
SYS-3-REGDFLT 267 Shared Memory Parity Error shared memory control
SYS-4-REGEXP 267 register error caused by slot access SYS-3-REGNONE 267 in bytes 433
SYS-3-REGTYPE 267 Shared Memory Parity Error shared memory control
SYS-5-RELOAD 268 register error caused by MPU access in SYS-4-RELOAD_ATTEMPT 268 bytes 433
SYS-5-RESTART 268 Unexpected exception to CPU vector PC SYS-2-RETBUF 269 434 SYS2-RETBUFI 269
SYS-2-SELF 269
20 System Error Messages Unexpected vectored interrupt vector offset TR-3-J3ADFIRM 282 434 TR3-BADFIRMTYPE 282
Unknown address TR-3-3ADFUNC 282 control reg Error at PC 434 TR-3-BADHEADER 282 SYS-6-TESTINFO 272 TR-3-BADMUL 283
SYS-3-TIMERHOG 272 TR-3-BADRNGNUM 283
SYS-3-TIMERNEG 272 TR-3-BADSLOT 283 SYS-3-TTYMEM 272 TR-3-BADSTART 284
SYS-2-WATCHDOG 273 TR-3-BADUNIT 284
SYS-3-WRONGFRBELIST 273 TR-4BKGND 284
SYS-2WRONGPOOL 273 TR-4-BKGNDINT 284 TR-3-BOOUSDATA 284
TR-3-BOOUSLENGTH 285
TR-3-COMPFAIL 285
TR-3-DIAOFAIL 285
TR-3-FILTFAIL 285 TAC-6-SENDTMO 275 TR-3-GETCONF 285 TAC-4-UNEXREP 275 TR-3-INCOM 286 TBRIDGE6-GIANT 276 TR-3-INITFAIL 286 TBRIDGE-4-INVALIDMEDIIA 276 TR-4-INTFAIL 286 TBRIDGE-4-NOMEMORY 276 TR-3-MADGETX 287 TBRIDGE-4--NOVCDROP 277 TR-3-MODBFAIL 287 TBRIDGE-4-NOVCFLOOD 277 TR-3-MODFAIL 287 T3RTDGE-4-SMF ACTION 277 TR-3-NOFIRM 287 TCP-2-ACCEPT 278 TR-3-NOMEMORY 287 TCP-6-BADAUTH 278 TR.-4-NOMOREPAGES 288 TCP-2-BUPFER 278 TR-3-NOPAK 288 TCP-2-NOTREADY 279 TR-3-OLDTRIF 288 TCP-6-NOTREADY 279 TR.-3-OPENFAIL 289 TCP-2-PUTBYTE 278 TR-3-OPENPAIL2 289 TCV-6-TOOBIG 279 TR3-PANIC 289 TMQ3-NOTFOUND 280 TR-3-PANICINF 290 TN-2-BADLOGIN 280 TR-3-PANICTYPE 290 TN-3-BADSTATE 280 TR3-RESETFAIL 290 TN3270-2-INP_OVF1 281 TR-3-RESETFAIL2 290 TN-3-READLINE 280 TR-3-RTFBADMAGIC 291 TR-3-ADPCHK 281 TR-3-RLFTBLTRASH 291 TR-3-ASYNCUSE 281 TR-3-SETBRIDGEFAIL 291 TR-4.-BADADAPT 282 TR-3-SETFAIL 291 TR-3-BADIBRDGPARMS 282 TR-3-SETFUNFAIL 292 TR-3-.BADBUFFSIZE 282 TR-3-SETGRPFAIL 292
Index 21 TR-3-SETOPTFAIL 292 Unknown control reg Error address at TR-3-SMTSTATFAIL 292 PC 434 TR-4-SNKBRIDG 292 UTIL-2-RANGEDUP 301
TR-3-STARTFAILED 292 UTIL-3-RANGEINCON 301
TR-3-STARTFAILED2 293 UTIL-3-RANGEJNVERT 301
TR-6-STATE 293 UTIL-3-RANGENULLINPUT 302
TR-3-STATFAIL 293 UTIL-2-RANGERET 301
TR-6-STATRING 293 TJTIL-3-TREE 302 TR-3--TRACMD 294 TR-4-UNKNOWNCOMP 294 TR-3--UNKNOWNT2M 294
TR-3-WIREFAULT 295
TUN-4-BADOUTMODE 295 \1NES2BADPARAM 302 TUN-4-RECURDOWN 295 VINES-2.-BADTJME 303 TUN-4--RECURS HUT 296 VINES2CACHEFATLED 303
VINES-2-CACHEUNSUPP 303
VINES-2-CONSISTENCY 303 VINES-2-CORRUPTENTRY 304
VINES-2-DUPADDR 304
UCODE-3-BADCFIKSUM 296 VINES-2-ENCAPFAILED 304 UCODE-3-BADHWVER 296 VINES-6-FNNOTFOUND 304
UCODE-3-HDRCORRUPT 297 VINES-2-INIT 305
UCODE-3APCBUFFAIL 297 VINES-2-INYALIDPATH 305
UCODE-3-JPCINITFAIL 297 VJNES-2-INYALIDROUTE 305
UCODE-3.-IPCINYALID 297 VINES-6-IPCNOROUTINE 305
UCODE-3-LDFAIL 298 VINES-2-NEIGHBOR 306 UCODE-3--NOBUF 298 VINES-2-NOBUFFERS 306 UCODE-3-NOFILE 298 VINES-2-.NOMEMORY 306 UCODE-3-NOROM 298 VINES-2-NOVENCAP 306 UCODE-5-OBSOLETE 299 VINES-2-REASSEMBLY 307
UCODE-3-OLDHARD 299 \TINES-6-RPCNOSERVICE 307 UCODE-3-RDPAIL 299 VINES-6-RTNNOTFOUND 307 UCODE-3-TOOBIG 299 VIP-3--BADMALUCMD 308 UCODE-3-VERSIONCK 300 VIP-3-CMDNOPASCB 308
UCODE-3-WRONGHARD 300 VIP-3-NODISPATCH 308
Unexpected exception to CPU vector PC VIP-2-NOICBS 308 434 VIP-3-UNDEFIDBTYPE 309
Unexpected vectored interrupt vector offset 434 UNIX-1-SYSABORT 300
22 System Error Messages X25-3-ADDRESBAD 309 X25-3--BADCONFIG 310 X25-4-BADMBIT 310
X25-4-BADUPCALL 311
X25-3-COMPERR 311
X25-4-DEBUG_LCI 311 X25-2-ILLP4 311
X25-3-INTJMEQ 311 X25-4-LARGEPKSIZE 312
X25-3-LCIBOGUS 312
X25-5-NOBUF 312 X25-3-NOLCI 311
X25-5-NOMEM 313
X25-3-NOTFINDBH 311
X25-3-NOTFINDI 311
X25-3-NOTFINDS 311
XNS-3-BADPATHS 317
XNS-2-BADROIJTE 317
X25-4-PARTIALMAP 313
X25-5-PBPDBIT 313
X25-5-PBPHOLDQ 313 X25-5-PBPNOEND 314 X25-3-PVCBAD 314 X25-3-PVCDELETE 314
X25-4-RANGEUNUSED 315 X25-3-SIZEBAD 315
X25-3-SPURD1 311
X25-3-SYNCBAD 315 X25-3-VCLOSTSYNC 316 X25-3-VERSIONBAD 316
X25-3-XOTPROTOCOL 316
Index 23 24 System Error Messages Corporate Headquarters Csco Systems Inc
170 West Tasnian Drive
San Jose CA 951341786 USA
World Wide Web URL
http//wwwciscocom Tel 408 526-4000
800 553-NETS 6387
Fax 408 526-4100
Cisco Systems has more than
125 sales offices worldwide
Call the companys corporate headquarters California USA at 408 526-4000 to contact your local account representative or in North America call 800 553-NETS 6387
Printed in the USA on recycled paper
contanrng 10% post consumer waste
78341701