2nd Generation TROUBLESHOOTING GUIDES

© 2009 Proprietary & Confidential TABLE OF CONTENTS

1. Snapshots of Antennas …………………………………………………………………… 3 2. Snapshots of Main Board ……………………………………………………………….... 5 3. Charging Troubleshooting ………………………………………………………………... 9 4. ALS/Proximity Sensor/LED/SD/SIM Troubleshooting ……………………..…………. 12 5. Touch/Display Troubleshooting …………………………………………………………. 19 6. Camera Troubleshooting ………………………………………………………………… 27 7. Vibrator and Sensors Troubleshooting ………………………………………………… 34 8. Audio Troubleshooting …………………………………………………………………… 39 9. Key Troubleshooting ……………………………………………………………………… 50 10. WCDMA/GSM Troubleshooting………………………………………………………… 53 11. WLAN / BT / FM Troubleshooting……………………………………………………… 120 12. DTV Troubleshooting……………………………………………………………………. 141 13. GPS Troubleshooting……………………………………………………………………. 153

Motorola Mobility Confidential Restricted: May 27, 2014 Page 2 Do not share without consent from Motorola

SNAPSHOTS OF ANTENNAS

Motorola Mobility Confidential Restricted: May 27, 2014 Page 3 Do not share without consent from Motorola Antenna and Antenna Feed Locations

Motorola Mobility Confidential Restricted: May 27, 2014 Page 4 Do not share without consent from Motorola SNAPSHOTS OF MAIN BOARD

Motorola Mobility Confidential Restricted: May 27, 2014 Page 5 Do not share without consent from Motorola Snapshots of Main PCB – Top and Bottom

Top Side Bottom Side

(Battery side) Second Mic (Display side) P+ALS sensor Audio jack Indicator LED Vibrator Rear camera Front camera SIM2 connector

SD card Battery connector connector

SIM1 connector Side Key Flash light

LCM and TP connector

USB connector Primary MIC

Motorola Mobility Confidential Restricted: May 27, 2014 Page 6 Do not share without consent from Motorola Front cam 1.8V power

Main Board – Top Placement

Hall sensor LCM IO power Backlight Power Volume Front cam Volume Bottom driver IC up up 2.8V power down SPK key key key AMP LCM bias IC Blank Flash Flash driver IC eMMC Rear Cam 1.8V power

2nd MIC Rear C a m

P)+ Rear 2.8V C Audio power USB Jack a C LPDDR(PO MSM8x26 m N T CNT

Top SPK AMP PMIC RCV/ S 19.2MHzP K Audioswitch codec

Gyro sensor

Motorola Mobility Confidential Restricted: May 27, 2014 Page 7 Do not share without consent from Motorola Main Board – Bottom Placement

GPS ANT Diversity ANT GPS BAT CNT SAW 1575.42 MHz 27MHz GPS LNA Bottom SPK DTV module contact WFR SP4T DTV SAW 836.5MHz SAW 2140MHz WFR2600

TOP SPK contact SAW GPS QFE11 1575.42MHz 0 WTR 2605 1 Duplexer Primary WCDMA B1 ANT Duplexer B2 Primary SIM/SD/ SIM/SD/ light/ Flash CNT Vibrator 1850-1990MHz MIC SAW filter TP 3.1V pwr 1842.5/1960MHz senso r/ WiFi/BT/ FM P+ALS CNT Indicator Front cam CNT Front Coupler LCM G+E 700-2700MH connecto

B1/B8 PA B1/B8 PA com B2/B5 PA B2/B5 PA z r SAW filter SAW 2450MHz pass Ant switch switch Ant WiFi Ant WiFi

Duplexer B8 Duplexer B26 sensor

Motorola Mobility Confidential Restricted: May 27, 2014 Page 8 Do not share without consent from Motorola CHARGING TROUBLESHOOTING

Motorola Mobility Confidential Restricted: May 27, 2014 Page 9 Do not share without consent from Motorola Charging Troubleshooting Charge path: USB connector CON1001 pin 1-> U1001 (pin 161, 172) -> U1001 (pin 162) -> U1001 (pin 143,155) -> U1001 (pin 154,166) -> L1001 -> U1001 (pin 152, 164) -> U1001 (pin 139, 151, 163) -> R1008 -> CON1002 (pin 4) USB TP1001 1 USB_ID 2 ESD1002 CON1001 AOZ8231ADI-12

7 6 UB012-04413A01 TP1002 TP1003 7 6 5 5 4 1 4 3 1 1 USB_DP_CON VREF_BAT_THM R1002 0R/+-5% USB_DP 3 2 USB_DM_CON R1003 0R/+-5% 2 1 USB_DM

1 1 1 1 8 9 C1002 C1003 1 1 ESD1001 C1001 R1001 ESD1003 ESD1004 R1005 TVM0G360M300R ESD7951ST5G 8 9 ESD7951ST5G 14.3K DUMMY_C_0603 2

2 2 DUMMY_C_0201DUMMY_C_0201 VBAT_THERM

2 2 U1001-2 R1004 TP1004 CHARGING 2.2K/+-1% VBUS 168 169 1 161 LED_CHG VREF_BAT_THM BAT_THERM 172 USB_IN_1 USB_IN_2 C1004 R1006 USB_ID 97 76 VCOIN C1005 47uF 1uF 47K/+-5% USB_ID_IN VCOIN 0603 0201_m03 C1006 10nF OVP_CP_DRV 171 BATTERY CONNECOT 162 OVP_CP_DRV OVP_OUT 170 VPRE_BYP C1007 100nF VPRE_BYP VBATT VDRV_P 167 154 VCHG C1008 100nF VDRV_P VSW_CHG_1 166 VSW_CHGL1001 1uH VSW_CHG_2

BMS_CSP 152 VPH_PWR_1 164 VPH_PWR_2 VPH_PWR R1008 Place as close to PMIC 10m/+-1% 110 C1009 GND_OVP as possible. BMS_CSM 156 142 10uF 139 VBAT_SNS GND_CHG 109 BMS_CSM VBATT VBAT_1 GND_CHG_PSUB TP1007 TP1008 151 C1010 C1011 163 VBAT_2 65 *TP50* *TP50* VBAT_3 GND_DRV 4.7uF 100nF 1 1

C1014 C1015 47uF 47uF 143 0805_m095 0805_m095 VREF_BAT_THM 155 VCHG_1 VCHG 153 VCHG_2 C1012 C1013 165 GND_CHG_HP_1 140 GND_CHG_HP_2 R1009 4.7uF 4.7uF BATFET_CP_DRV 92 CON1002 TP1005 TP1006 100K/+-1% GND1 5 0201_m03 5 4 64

1 1 GND2 4 3 C1016 74 BAT_ID GND3 3 2 BAT_THERM 75 2 1 DUMMY_C_0402 GND4 86

6 1 2 2 GND5 87 6 GND6 98 2 2 GND7 201-C0800-00414 99 ESD1005 GND8 ESD1006 ESD9B5.0ST5G ESD9B5.0ST5G PM-8226-0-172WLNSP-TR-07-1-VV 1 1 1 1

Motorola Mobility Confidential Restricted: May 27, 2014 Page 10 Do not share without consent from Motorola Charging Troubleshooting

In the event of charging issues, check charging voltages along the charging path: ● Check the battery is inserted the CON1002 or not ● Check battery ID voltage at TP1006 about 1V ● Check thermistor voltage at TP1005 about 0.63V ● Measure USB_PWR charger input voltage at TP1004. The voltage should be between 4.75V~5.25V.

● Measure VCHG voltage at C1012. The voltage should be lower the USB_PWR.

● Check battery voltage at CON1002 pin4. It should be 4.35V or lower. If battery is 2.1 or 0, there maybe a short in the circuit somewhere. The battery fault safe circuit is triggered.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 11 Do not share without consent from Motorola ALS + PROXIMITY SENSOR/ INDICATOR LED/ MICRO-SD/ MICRO-SIM/ TROUBLESHOOTING

Motorola Mobility Confidential Restricted: May 27, 2014 Page 12 Do not share without consent from Motorola ALS + Proximity sensor

• ALS + proximity sensor are built into U101 • MSM8226 U401 uses I2C bus to communicate to U101

VREG_L19_2P85 R103 22R/+-5% C101

4.7uF U101 VDD 8 1 SENSORS_I2C_SDA VDD SDA SENSORS_I2C_SCL 7 2 PROXIMITY_INT SCL /INT 6 3 GND LDR

R102 0R/+-5% LEDA 5 4 2 2 LEDA NC STK3310 C102 2 2 ESD101 ESD103 1uF AZ5A25-01F.R7G AZ5A25-01F.R7G

ESD102 ESD104 1 1 AZ5A25-01F.R7G AZ5A25-01F.R7G 1 1

I2C address: 0x48

Motorola Mobility Confidential Restricted: May 27, 2014 Page 13 Do not share without consent from Motorola ALS + Proximity sensor (cont.)

•sensor Check wrong I2C bus reading activities during ALS + proximity sensor access (SENSORS_I2C_SDA, SENSORS_I2C_SCL) • Check CON101 on ALS + Proximity sensor FPC and CON2101 on phone board are corrected soldering

In the event of ALS + proximity sensor issue at phone level: • Check for missing/missed alignment of rubber seal • Missing/missed alignment of rubber seal can cause ALS + proximity sensor wrong reading

Motorola Mobility Confidential Restricted: May 27, 2014 Page 14 Do not share without consent from Motorola Indicator LED

• Status white LEDs is driven by U1001 PM8226 MPP_4 (pin 157)

VPH_PWR + 1 LED102 16-213/T3D-CP2Q2TY/3T - 2 WLED_SINK 2

ESD105 AZ5A25-01F.R7G 1

In the event of white status LED issue: • Check voltage at LED Anode (pin 2) and Cathode (pin 1) of LED102 • LED Anode voltage = VPH_PWR and Cathode voltage = VPH_PWR – In the event of white status LED issue:

Motorola Mobility Confidential Restricted: May 27, 2014 Page 15 Do not share without consent from Motorola Micro-SD

• uSD connector is operated with its own power, detection and SDC bus interface

CON103 5040771891 11 10 MICRO SD CARD CONNECTOR 11 10

8 SDC2_DATA_1 12 DAT1 7 SDC2_DATA_0 12 DAT0 6 SD_CARD_DET_N 15 VSS 5 SDC2_CLK DETECT SWITCH TERM CLK 4

1 VREG_L18_2P95 13 VDD 3 SDC2_CMD ESD112 13 CMD 2 SDC2_DATA_3 CD/DAT3 1 SDC2_DATA_2 TVM0G100M010R DATA2 2 C109 1 1 1 1 1 1 C110 1 DETECT LEVER TERM 14 9 ESD105 ESD106 ESD107 ESD108 ESD109 ESD110 1uF ESD111 TEA10402V05A0 TEA10402V05A0 TEA10402V05A0 TEA10402V05A0 TEA10402V05A0 TEA10402V05A0 9 16 14 TVM0G100M010R 2 2 2 2 2 2 2

In the event of uSD issue: • Do a through visual check on uSD connector CON103 for any sign of mechanical contact issues • Insert uSD and detected SD_CARD_DET_N=low at TP1711 • Check the voltage VREG_L18_2P95 at TP1712 on board level • Check uSD bus interface signal activities during uSD access (SDC_CLK, SDC_CMD, uSD_DATA)

Motorola Mobility Confidential Restricted: May 27, 2014 Page 16 Do not share without consent from Motorola SIM

• Depending on the PCB board variant, there are up to 2 SIM connectors on PCB board • Each SIM connector is operated independently with its own power, detection and SIM bus interface SIM1 CARD CONNECTOR

Sim card Sim Det Insert Not Insert

Voltage 1.8V 0V(GND) Level VREG_L22_UIM1 C101 C102 CON101 100nF HD3 HD4 HD3 HD4 UIM1_DETECT DSW2 DSW2 C5 C1 C6 GND Vcc C2 UIM1_RST VREG_L22_UIM1_VPP UIM1_DATA C7 Vpp RST C3 UIM1_CLK I/O CLK C107 HD2_DSW1 HD1 SIM2 CARD CONNECTOR HD2_DSW1 HD1 SF56S006V4A

VREG_L23_UIM2

ESD103 C103 UIM1_DETECT 1 6 UIM1_CLK 100nF C104 CH1 CH5 CON102 HD3 HD4 2 5 UIM1_RST VN CH4 HD3 HD4 VREG_L22_UIM1 3 4 UIM1_DATA UIM2_DETECT DSW2 CH2 CH3 DSW2 C5 C1 AOZ8235DI C6 GND Vcc C2 UIM2_RST VREG_L23_UIM2 UIM2_DATA C7 Vpp RST C3 UIM2_CLK I/O CLK C108 HD2_DSW1 HD1 HD2_DSW1 HD1 SF56S006V4A

ESD104 VREG_L23_UIM2 1 6 UIM2_RST CH1 CH5 2 5 UIM2_CLK VN CH4 UIM2_DETECT 3 4 UIM2_DATA CH2 CH3 AOZ8235DI Motorola Mobility Confidential Restricted: May 27, 2014 Page 17 Do not share without consent from Motorola SIM (cont.)

In the event of SIM issue: • Do a through visual check on SIM connector CON101/CON102 for any sign of mechanical contact issues • Check SIM power at TP1701/ TP1714 and SIM card detection signal TP1705/ TP1718 (active HIGH when SIM card is inserted) • Check SIM bus interface signal activities during SIM access (UIMx_RST, UIMx_CLK, UIMx_DATA)

Motorola Mobility Confidential Restricted: May 27, 2014 Page 18 Do not share without consent from Motorola TOUCH AND DISPLAY TROUBLESHOOTING

Motorola Mobility Confidential Restricted: May 27, 2014 Page 19 Do not share without consent from Motorola Module Shape

Receiver/Top speaker

PIN1 LCM+ TP FLEX

TP Driver IC

PIN41

Bottom speaker

Motorola Mobility Confidential Restricted: May 27, 2014 Page 20 Do not share without consent from Motorola Assembly

Motorola Mobility Confidential Restricted: May 27, 2014 Page 21 Do not share without consent from Motorola Schematic on Touch Panel Connector

TP_INT_N=1.8V (High) VREG_LVS1_1P8 State change interrupt. TP_RST_N from MSM GPIO_16Low when touch event occurs R1808 LCM/TP CONNECTOR 100K/+-5% TP_INT_N

TP_I2C_SCL

TP_RST_N

TP_I2C_SDA V_TP_AVDD R1815 VREG_L15_3P1 R1811 V_TP_DVDD R1810

VREG_LVS1_1P8 2 2 2 2 2 V_TP_3P1 ESD1818 C1816 ESD1820 C1818 ESD1819 C1817 ESD1821 C1821 ESD1815 2 ESD1816 AZ5A25-01F.R7G AZ5A25-01F.R7G AZ5A25-01F.R7G AZ5A25-01F.R7G AZ5A25-01F.R7G AZ5A25-01F.R7G C1814

C1815 43 CON1801 100nF 41

100nF 39 41 43 40 DUMMY_C_0201 DUMMY_C_0201 DUMMY_C_0201 DUMMY_C_0201 37 39 40 38 1 1 1 1 1 1 35 37 38 36 I2C lines (SCL, SDA) should be 33 35 36 34 31 33 34 32 pulled up to 1.8V 29 31 32 30 27 29 30 28 25 27 28 26 23 25 26 24 21 23 24 22 19 21 22 20 17 19 20 18 15 17 18 16 13 15 16 14 11 13 14 12 9 11 12 10 7 9 10 8 5 7 8 6 3 5 6 4 1 3 4 2

1 42 2 GB3RF411-1101-7H TP42 AVDD POWER

U1804 1 2 VPH_PWR VDD CE TP_AVDD_EN TP_AVDD_EN from MSM GPIO_73 4 3 V_TP_3P1 VOUT GND RP102Z311D-TR-F

C1822 C1823 Output 3.1V to TP AVDD 1uF 1uF

Motorola Mobility Confidential Restricted: May 27, 2014 Page 22 Do not share without consent from Motorola Troubleshooting

• No touch: 1) Check touch connector and flexes on display flex and board level connector CON1801 2) Check power supply voltages; a. V_TP_3P1(C1823 ) = 3.1V b. VREG_LVS1_1P8 (C1815) = 1.8V 3) Measure INT, RST,I2C signal are correct

Motorola Mobility Confidential Restricted: May 27, 2014 Page 23 Do not share without consent from Motorola Schematic on LCM Connector

Backlight power

43 CON1801 41

39 41 43 40 Backlight power 37 39 40 38 35 37 38 36 33 35 36 34 31 33 34 32 LED+ 29 31 32 30 LED2- 27 29 30 28 LED1- LCM_ID1 25 27 28 26 LCM_ID0 +5P5V -5P5V 23 25 26 24 LCM_VIO R1803 2 21 23 24 22 LCD_IOVDD ESD1809 ESD1810 ESD1806 19 21 22 20 PWM_LED R1814

1 2 VREG_L8_1P8 ESD1803 MIPI_DSI0_LANE2_P_1 17 19 20 18 TVM0G360M300R AOZ8231ADI-12 15 17 18 16 MIPI_DSI0_LANE2_M_1 2 ESD1813 2 ESD1811 ESD1804 2 ESD1805 R1804 MIPI_DSI0_LANE1_M_1 13 15 16 14 MIPI_DSI0_LANE1_P_1 C1806 C1807 MIPI_DSI0_CLK_P_1 11 13 14 12 AZ5A25-01F.R7G AZ5A25-01F.R7G AOZ8231ADI-12 AZ5A25-01F.R7G

2 Digital I/O power to LCM 9 11 12 10 MIPI_DSI0_CLK_M_1 100nF 1uF 1 MIPI_DSI0_LANE0_M_1 7 9 10 8 MIPI_DSI0_LANE0_P_1 DISP_RESET_N MIPI_DSI0_LANE3_P_1 5 7 8 6 3 5 6 4 MIPI_DSI0_LANE3_M_1 1 1 1 1 1 3 4 2 LCD_TE

1 42 2 GB3RF411-1101-7H Reset signal from MSM GPIO25 42 +-5.5V power to LCM ESD1823 ESD1812 ESD1822

MIPI interface

Motorola Mobility Confidential Restricted: May 27, 2014 Page 24 Do not share without consent from Motorola Schematic on LCM Power (+/-5.5V, LED+,LED-,LED2-,LCD_IOVDD) Back Light IC(Boost) LCM IO POWER

LED+ VPH_PWR D1801 L1802 22uH BL_SW 1 2 VPH_PWR ANODE CATHODE CRS13 U1803 C1808 A3 1uF C3 D1 IN OVP U1802 A1 SW RP103K181D-TRB BL_I2C_SDA C1810 C1811 A2 SDA C1812 C1813 BL_I2C_SCL SCL 4 1 1uF DUMMY_C_0402 VDD VOUT LCD_IOVDD 4.7uF R1812 100K/+-1% VREG_L6_1P8 B2 D3 BL_INT_N LED1- INTN ILED1 3 2 C1809 B1 D2 LCD_IOVDD_EN CE GND BL_EN HWEN ILED2 LED2- 1uF d GND PWM_LED C1 C1819 C1820 PWM a C2 VREG_L6_1P8 5

SEL GND R1813 LM3630ATMX R1807

10K/+-5% B3 DUMMY_R_0201 DUMMY_C_0402DUMMY_C_0402

‧ SEL-->VIN I2C address: 0x38 ‧ SEL-->GND VPH_PWR I2C address: 0x36

C1801 U1801 Troubleshooting Tips: 4.7uF C1 D1 LCM_SW L1801 4.7uH VIN SW E3 a. LCD_IOVDD_EN GPIO_10 (R1807) OUTP +5P5V D3 C1802 b. LCD BIAS_P_EN GPIO_12 (R1802) B1 REG1 E2 C1803 4.7uF bLCD BIAS_P_EN A1 ENP REG2 4.7uF c. LCD BIAS_N_EN GPIO_13 (R1801) LCD BIAS_N_EN ENN c B2 d. BL_EN GPIO_5 (R1813) BL_I2C_SCL SCL A2 C2 OUTN -5P5V BL_I2C_SDA above signal are from MSM when the LCM on, SDA C1804 B3 C3 4.7uF enable signal should be pull up to 1.8V E1 PGND1 CFLY1 D2 PGND2 A3 C1805 e. I2C lines (SCL, SDA) should be pulled up to 1.8V AGND CFLY2 2.2uF TPS65132A0YFFR R1801 R1802

DUMMY_R_0201 DUMMY_R_0201

Motorola Mobility Confidential Restricted: May 27, 2014 Page 25 Do not share without consent from Motorola Troubleshooting

• No display: 1. Check Backlight Power Supply voltages: a. LED+ (C1812) b. LED1- (C1819) c. LED2- (C1820) 2. Check LCM Power Supply voltages: a. +5.5V (C1802) b. -5.5V (C1804) c. LCD_IOVDD (C1809) • Check to make sure there is data activity on all MIPI differential pair lines while display is on (TP1801,TP1802,TP1803,TP1804).

• Check reset line CON1801 pin 22. It should be set high (1.8V) after power on.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 26 Do not share without consent from Motorola CAMERA TROUBLESHOOTING

Motorola Mobility Confidential Restricted: May 27, 2014 Page 27 Do not share without consent from Motorola Rear Camera

n The image sensor is a diagonal 5.7 mm (Type 1/3.2) CMOS active type image sensor with a square pixel array and 8.08M effective pixels. n The sensor consists of a minimum of 3280 active horizontal pixels and 2464 active vertical pixels. n This module has an Auto Focus (AF) module with integrated driver (VCM). n Data interface: (1 pair-clk, 4 pair-data) mobile industry processor interface (MIPI). I2C is used for control. n Analog Supply regulator (2.8V) located on Main PCB.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 28 Do not share without consent from Motorola Rear Camera (cont.)

8M REAR CAMERA

VREG_L28_2P8

C1901 1 ESD1906 CON1901 4.7uF TVM0G100M010R 2 1 MIPI_CSI0_LANE1_P_1 4 2 1 3 MIPI_CSI0_LANE1_M_1 2 MIPI_CSI0_LANE2_P_1 6 4 3 5 MIPI_CSI0_LANE3_P_1 MIPI_CSI0_LANE2_M_1 8 6 5 7 MIPI_CSI0_LANE3_M_1 MIPI_CSI0_LANE0_P_1 10 8 7 9 MIPI_CSI0_LANE0_M_1 12 10 9 11 MIPI_CSI0_CLK_P_1 14 12 11 13 CAM_I2C_SDA MIPI_CSI0_CLK_M_1 16 14 13 15 CAM_I2C_SCL R1905 18 16 15 17 VREG_L19_2P85 20 18 17 19 VREG_L5_1P2 RCAM_RST_N RCAM_AVDD 22 20 19 21 V_RCAM_AVDD_2P8 R1903 L1901 600R R1904 RCAM_DOVDD 24 22 21 23 RCAM_MCLK R1901 RCAM_DOVDD_1P8 24 23 CAM_MCLK0 R1906 DF30FC-24DS-0.4V(81)

VREG_LVS1_1P8 1 1 1 1 1 1 1 C1902 C1903 ESD1912 ESD1911 ESD1904 ESD1913 ESD1901 ESD1903 ESD1902 C1920 TVM0G100M010R TVM0G100M010R TVM0G100M010R TVM0G100M010R TVM0G100M010R TVM0G100M010R TVM0G100M010R 4.7uF 4.7uF 4.7uF C1918 2 2 2 2 2 2 2 100pF

When rear camera assemble correctly and app turn on, there is no function

Troubleshooting Tips1: a. Check Main reference clk = 24Mhz REAR CAM DOVDD POWER b. Check MIPI data/clk exist on all lines VPH_PWR C1904

After imager APP is launched. 1uF U1901 RP114K181D-TRB 4 1 c. Check VREG_L5_1P2 is high (1.2V), C1920 VDD VOUT RCAM_DOVDD_1P8 C1905 3 2 d. Check V_RCAM_AVDD_2P8= 2.8V, L1901 RCAM_DOVDD_EN CE GND1 GND 1uF

e. Check RCAM_DOVDD_1P8 = 1.8V, C1903 5 f. Check VREG_L28_2P8 = 2.8V, C1901 g. Check I2C clk/sda activity is present. REAR CAM AVDD POWER

h. Check reset is high (1.8V), CON1901 pin19 VPH_PWR C1922 Troubleshooting Tips2: 1uF U1905 RP114K281D-TRB 4 1 a. RCAM_AVDD_EN (GPIO_27) VDD VOUT V_RCAM_AVDD_2P8 C1921 3 2 RCAM_AVDD_EN b. RCAM_DOVDD_EN (GPIO_33) CE GND1 GND 1uF above signal are from MSM when the LCM on, 5 enable signal should be pull up to 1.8V

Motorola Mobility Confidential Restricted: May 27, 2014 Page 29 Do not share without consent from Motorola Front Camera

§ The sensor is a diagonal 2.59 mm (Type 1/6.95) back-illuminated type CMOS image sensor with a square pixel array and approx. 2.4 M effective pixels. § The sensor consists of a minimum of 1976 active horizontal pixels and 1200 active vertical pixels. § The Module is capable of auto exposure, white balance, color correction, and color conversion. § This device provides a finished image at up to 30 fps (frames per second) image data at 1976x1200 full resolution on a mobile device to enable image capture and video clip capture. § Analog Supply regulator (2.8V) located on PCB.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 30 Do not share without consent from Motorola Front Camera (cont.)

VREG_L19_2P85 R1907 FCAM_AVDD V_FCAM_AVDD_2P8 R1909 0R/+-5% L1902 600R

VREG_LVS1_1P8 R1908 FCAM_DOVDD FCAM_DOVDD_1P8 R1910

C1909 C1913 2 2

4.7uF 4.7uF ESD1914 ESD1915 AZ5A25-01F.R7G AZ5A25-01F.R7G 2M FRONT CAMERA 1 1 CON1902 VREG_L5_1P2 25 26

2 25 26 C1915 1 2 ESD1916 3 1 2 4 4.7uF AZ5A25-01F.R7G TP1919 1 FCAM_XVS 5 3 4 6 7 5 6 8 1 TP1912 9 7 8 10 1 TP1913 1 11 9 10 12 CAM_I2C_SDA 13 11 12 14 MIPI_CSI1_CLK_P_1 CAM_I2C_SCL 15 13 14 16 MIPI_CSI1_CLK_M_1 FCAM_STANDBY_N FCAM_MCLK 17 15 16 18 CAM_MCLK0 R1902 19 17 18 20 MIPI_CSI1_LANE0_P_1 21 19 20 22 MIPI_CSI1_LANE0_M_1 2 ESD1907 2 ESD1908 2 ESD1910 2 ESD1909 23 21 22 24 C1919 23 24 AZ5A25-01F.R7G AZ5A25-01F.R7G AZ5A25-01F.R7G AZ5A25-01F.R7G DUMMY_C_0201 27 28 27 28 BM20B(0.6)-24DS-0.4V(51) 1 1 1 1

When front camera assemble correctly and app turn on, there is no function FRONT CAM AVDD POWER

Troubleshooting Tips1: VPH_PWR a. Check CAM_MCLK0 = 24Mhz, C1919 C1907 1uF U1903 RP114K281D-TRB b. Check MIPI data/clk exist on all lines 4 1 VDD VOUT V_FCAM_AVDD_2P8 After imager APP is launched. C1911 3 2 FCAM_AVDD_EN c. Check VREG_L5_1P2 is high (1.2V), C1915 CE GND1 GND 1uF d. Check V_FCAM_AVDD_2P8= 2.8V, L1902 5 e. Check FCAM_DOVDD_1P8= 1.8V, C1913 FRONT CAM DOVDD POWER f. Check I2C clk/sda activity is present. g. Check reset is high (1.8V), CON1902 pin15 VPH_PWR C1906

1uF U1902 Troubleshooting Tips2: RP114K181D-TRB 4 1 a. FCAM_AVDD_EN (GPIO_34) VDD VOUT FCAM_DOVDD_1P8 C1910 3 2 b. FCAM_DOVDD_EN (GPIO_36) FCAM_DOVDD_EN CE GND1 GND 1uF

above signal are from MSM when the LCM on, 5 enable signal should be pull up to 1.8V

Motorola Mobility Confidential Restricted: May 27, 2014 Page 31 Do not share without consent from Motorola FLASH-LED

• Flash LED Driver used for camera flash • Still image flash controlled via SW control programming MSM8226 GPIOs. • Torch Mode (LED continuously on in video mode) controlled via MSM8226 GPIOs. • Flash duration and brightness configured via I2C. • Low current torch mode used for image pre-capture.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 32 Do not share without consent from Motorola FLASH-LED

From MSM8226 signal Flash LED Driver

U1904

A3 LM3642TLX NOPB TP1920 C3 *TP50* FLASH_I2C_SCL SCL C2 GND FLASH_I2C_SDA C1 SDA FLASH_TORCH B2 TX/TORCH B1 1 FLASH_STROBE STROBE LED FLASH_OUT

VPH_PWR

B3 A1

IN SW OUT

C1916 A2 C1917 L1903 1uH FLASH_SW FLASH-LED connects to 10uF 10uF FLASH_OUT via flex assembly.

Troubleshooting Tips: FLASH LED Check VPH_PWR supply (always on). FLASH_OUT

Check output voltage on FLASH_OUT is about 3.0V at 2 TP1920 when FLASH event is enabled. LED101 LUW CAEP.G4-MYNX-G3-1-A00-R18-Z-XX / Q65111A3068

Check CON1701 are making good connection with 1 FLASH-LED assembly.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 33 Do not share without consent from Motorola VIBRATOR AND SENSORS TROUBLESHOOTING

Motorola Mobility Confidential Restricted: May 27, 2014 Page 34 Do not share without consent from Motorola Vibrator VIBRATOR

VDP VPH_PWR L101 68nH 1 C111 DUMMY_C_0201 1

100nF ESD101 VIB101 1 ESD7951ST5G 2 C113 D101 + 3

2 1 3 PMEG3005EL - 2 BMR-3135A Control by PM IC 2 VIB_DRV_N L102 68nH VDN 1 1

ESD102 - The vibrator is controlled by PMIC. ESD7951ST5G 2 - Driving voltage is about 1.9V when 2 alert operation event occur.

• Troubleshooting tips • No operation: Check driving voltage and check if vibrator shaft is bent. • Noisy operation: Check if vibrator shaft is bent.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 35 Do not share without consent from Motorola Sensor – G + E-Compass

1.8V SENSORS_I2C_SCL I2C Signal SupplVREG_LVS1_1P8 SENSORS_I2C_SDA y

2.85V Supply U2101 12 13 14 BMC150 Interrupt

11 PS 1

SDI VREG_LVS1_1P8 VREG_L19_2P85 10 SCK CSB SDO 2 Signal 9 VDDIO INT1 3 G-SENSOR_INT1 8 GND INT2 4 G-SENSOR_INT2 VDD DRDY GND GND INT3 C2102 100nF C2103 7 6 5 100nF E-COMPASS_INT

I2C address: ‧ SDO-->VIO G-Sensor: 0x11 E-Compass: 0x13 ‧ SDO-->GND G-Sensor: 0x10 E-Compass: 0x12 • Troubleshooting tips • No operation: Check if supply voltages (VREG_LVS1_1P8=1.8 and VREG_L19_2P85= 2.85) are correct. • Check if I2C and interrupt signals are operating when the sensor is in operation mode.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 36 Do not share without consent from Motorola Sensor – Gyro

Gyro

2.85V Supply VREG_LVS1_1P8

VREG_L19_2P85 R2102 100K/+-5% INT signal

GYRO_INT2_N 1.8V Supply C2101 100nF U2102 12 BMG160 VREG_LVS1_1P8 1 11 2 NC GNDIO 10 VDD VDDIO 3 INT2 9 VREG_LVS1_1P8 4 GND SDx 8 SENSORS_I2C_SDA 5 INT1 SDO 7 SENSORS_I2C_SCL C2104 CSB PS SCx 100nF 6 R2101 VREG_LVS1_1P8 INT signal 100K/+-5% I2C address: GYRO_INT1_N ‧ SDO-->GND Gyro: 0x68 I2C signal ‧ SDO-->VIO Gyro: 0x69 • Troubleshooting tips • No operation: Check if supply voltages (VREG_LVS1_1P8=1.8 and VREG_L19_2P85= 2.85) are correct. • Check if I2C and interrupt signals are operating when the sensor is in operation mode.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 37 Do not share without consent from Motorola Sensor – Hall Effect Sensor

HALL SENSOR

VREG_L6_1P8 U2103

C2107 4 3 100nF Vdd NC 2 GND 5 1 HALL_SENSOR_INT OUTPUT NC

AH1883-ZG-7

• Troubleshooting tips • No operation: Check supply voltage VREG_L6_1P8 = 1.8 • Check if HALL_SENSOR_INT goes low when a magnetic is closed.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 38 Do not share without consent from Motorola AUDIO TROUBLESHOOTING

Motorola Mobility Confidential Restricted: May 27, 2014 Page 39 Do not share without consent from Motorola Audio Devices

3.5mm Headset Jack Earpiece/ Secondary Microphone Top Speaker

Front view Back view BACK

Bottom Primary Microphone Speaker

Motorola Mobility Confidential Restricted: May 27, 2014 Page 40 Do not share without consent from Motorola Mic Locations and Functions

Functional Name: Secondary Microphone

Factory Nomenclature: Noise cancelling mic, mic 2

Uses: • Noise suppression for voice calls • Multimedia audio recording

Functional Name: Main Microphone

Factory Nomenclature: Primary, mic 1 Front view

Uses: • Speech in handset and speakerphone modes

Motorola Mobility Confidential Restricted: May 27, 2014 Page 41 Do not share without consent from Motorola “No Audio” Complaints

• The FQC mode can be used to verify a broken audio path. – The “Receiver Test” for receiver function testing – The “Speaker Test” for speaker function testing – The “Headset loopback Test” for headset function testing – The “Mic1 Headset loopback Test” for MIC1 function testing – The “Mic2 Headset loopback Test” for MIC2 function testing

• If someone function is not work, this function may be damaged.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 42 Do not share without consent from Motorola Earpiece Speaker (Receiver)

SPK/RCV SWITCH TOP SPEAKER AMP VREG_L6_1P8

VPH_PWR EAR_P_1 EAR_P_IN EAR10_P C1653 0R/+-5% R1643 300K/+-1% C1650 0R/+-5% EAR_M_1 R1644 300K/+-1% EAR_M_IN C1641 C1642 C1645

EAR10_M 1 100nF 100nF 10uF ESD1613 C1633 AOZ8231ADI-12 1nF U1607 TP1613 T_SPK_IN_P B3 C2 B2 PGND EN TOP_SPK_AMP_EN SP1603 2 1 U1606 10 9 8 B1 PVDD A2 T_SPK_OUTP-2 L1612 NP T_SPK_P_CON 1 QP-15G VDD GND R1632 1

EAR_P_IN 1 1A 7 SPK_RCV_SW_P C1 C3 T_SPK_OUTP-1 NP 1B0

1B1 VCC S1 IN- Vo+ SPK_RCV_SEL R1633 C1638 T_SPK_IN_M 2 6 SPK_RCV_SW_N A1 A3 T_SPK_OUTN-1 NP 2B0 S2 IN+ Vo- SP1604

2B1 GND 2A TPA2011D1YFFR T_SPK_OUTN-2 L1606 NP T_SPK_M_CON 1 QP-15G FSA2269UMX 1 3 4 5 EAR_M_IN 1 1 C1639 1nF TP1614

T_SPK_P T_SPK_IN_P LINE_OUT_T_SPK C1649 10nF R1641 30K/+-1% U1606 ESD1614 C1646 10nF T_SPK_M R1642 30K/+-1% T_SPK_IN_M AOZ8231ADI-12

SPK_RCV_SEL 2

RCV HIGH

SPK LOW

• Checking if any open happened on the earpiece speaker series components. • Checking if any short to ground happened in the shunt components

Motorola Mobility Confidential Restricted: May 27, 2014 Page 43 Do not share without consent from Motorola Top Speaker SPK/RCV SWITCH TOP SPEAKER AMP VREG_L6_1P8

VPH_PWR EAR_P_1 EAR_P_IN EAR10_P C1653 0R/+-5% R1643 300K/+-1% C1650 0R/+-5% EAR_M_1 R1644 300K/+-1% EAR_M_IN C1641 C1642 C1645

EAR10_M 1 100nF 100nF 10uF ESD1613 C1633 AOZ8231ADI-12 1nF U1607 TP1613 T_SPK_IN_P B3 C2 B2 PGND EN TOP_SPK_AMP_EN SP1603 2 1 U1606 10 9 8 B1 PVDD A2 T_SPK_OUTP-2 L1612 NP T_SPK_P_CON 1 QP-15G VDD GND R1632 1

EAR_P_IN 1 1A 7 SPK_RCV_SW_P C1 C3 T_SPK_OUTP-1 NP 1B0

1B1 VCC S1 IN- Vo+ SPK_RCV_SEL R1633 C1638 T_SPK_IN_M 2 6 SPK_RCV_SW_N A1 A3 T_SPK_OUTN-1 NP 2B0 S2 IN+ Vo- SP1604

2B1 GND 2A TPA2011D1YFFR T_SPK_OUTN-2 L1606 NP T_SPK_M_CON 1 QP-15G FSA2269UMX 1 3 4 5 EAR_M_IN 1 1 C1639 1nF TP1614

T_SPK_P T_SPK_IN_P LINE_OUT_T_SPK C1649 10nF R1641 30K/+-1% U1606 ESD1614 C1646 10nF T_SPK_M R1642 30K/+-1% T_SPK_IN_M AOZ8231ADI-12

SPK_RCV_SEL 2

RCV HIGH

SPK LOW • Checking if any open happened on the speaker series components • Checking if any short to ground happened in shunt components • The loudspeaker can be probed at TP1613 and TP1614 • The impedance of the loudspeaker should be around 8Ω when probing on component • The output is a class D waveform (sample wave shown below)

Motorola Mobility Confidential Restricted: May 27, 2014 Page 44 Do not share without consent from Motorola Bottom Speaker

VPH_PWR

C1619 C1620 C1658 BOTTOM SPEAKER AMP 1 ESD1606 100nF 10uF AOZ8231ADI-12

U1605 C1622 TP1610 B3 C2 1nF B2 PGND EN BOT_SPK_AMP_EN SP1601 B1 PVDD A2 B_SPK_OUTP-2 2 1 L1615 NP B_SPK_P_CON 1 QP-15G VDD GND R1634 1 B_SPK_P B_SPK_IN_P C1 C3 B_SPK_OUTP-1 LINE_OUT_B_SPK C1626 10nF R1630 30K/+-1% NP IN- Vo+ R1635 C1628 C1627 10nF B_SPK_M R1631 30K/+-1% B_SPK_IN_M A1 A3 B_SPK_OUTN-1 NP IN+ Vo- SP1602 TPA2011D1YFFR B_SPK_OUTN-2 L1616 NP B_SPK_M_CON 1 QP-15G 1 1 1 C1632 1nF TP1611

ESD1609 AOZ8231ADI-12 2

• Checking if any open happened on the speaker series components • Checking if any short to ground happened in the shunt components • The loudspeaker can be probed at TP1610 and TP1611 • The impedance of the loudspeaker should be around 8Ω when probing on component • The output is a class D waveform (sample wave shown below)

Motorola Mobility Confidential Restricted: May 27, 2014 Page 45 Do not share without consent from Motorola Primary Microphone

MAIN MIC MIC_BIAS1

TP1609 MIC1_BIAS R1628 1K/+-5% T_POINT_S2 4 MIC1601 1 C1624 1 ESD1608

L1607 1K MIC1_OUTP_1 1 VDD 4.7uF MIC_IN1_P OUTPUT TVM0G100M010R 2 ESD1607 C1625 SFI0402-120E330NP-LF GND4 GND3 GND2 GND1 MOE-C110R38-K1 6 5 3 2

MIC_IN1_M L1608 1K C1629 C1630

Close to WCD9302

If the Primary mic is not functioning… • Check mic bias at C1624. This should be 1.8V when the microphone is enabled. • Check the microphone assembly to make certain it is not damaged, which may indicate a broken diaphragm

Motorola Mobility Confidential Restricted: May 27, 2014 Page 46 Do not share without consent from Motorola Secondary Microphone

ECHO MIC MIC_BIAS1 TP1612 MIC2_BIAS R1636 1K/+-5% T_POINT_S2 4 MIC1602 2 ESD1611 C1635 1 AOZ8231ADI-12

L1609 1K MIC2_OUTP_1 1 VDD 4.7uF

MIC_IN3_P 2 OUTPUT ESD1610 AOZ8231ADI-12 C1634 1 GND4 GND3 GND2 GND1 MOE-C110R38-K1 6 5 3 2 1 MIC_IN3_M L1611 1K C1636 C1637

Close to WCD9302

If the Secondary mic is not functioning… • Check mic bias at C1635. This should be 1.8V when the microphone is enabled. • Check the microphone assembly to make certain it is not damaged, which may indicate a broken diaphragm

Motorola Mobility Confidential Restricted: May 27, 2014 Page 47 Do not share without consent from Motorola 3.5mm Headset TP1602 *TP50* 1 CDC_HPH_REF L1605 70R

DUMMY1601 DUMMY-SHORT 0201

C1640 DTV_ANT_1 TP1601 DTV_ANT R1604 0R/+-5% *TP50* 12nH HEADSET C1605 1 Unmount. DUMMY_C_0201 C1654 6pF CON1601 R1611 20K/+-1% MBHC_IN TP1604 TP1603 HPH_GND2 *TP50* *TP50* 3 4

HPH-C_L_1 HPH-C-JACK_L_CON 1 1 HPH_L R1601 L1601 1000R HPH-C_R_1 L1602 1000R HPH-C-JACK_R_CON DUMMY-SHORT 0201 C1602 L1603 1000R HS_DET_N_CON 5 R1606 L1604 1000R HPH_MIC_CON 1 C1601 33pF DUMMY_R_0201 DUMMY_C_0201 1 1 1 2 1 ESD1601 ESD1602 ESD1603ESD1604 ESD1615 AJ017-14346A01 C1655 C1656 TEA10402V05A0 TEA10402V05A0 TEA10402V05A0 AOZ8231ADI-12 TEA10402V05A0 150pF 150pF

R1607

HPH_R 2 2 2 2

DUMMY-SHORT 0201 C1608 1

C1607 33pF DUMMY_C_0201 TP1605 *TP50* DUMMY1602

1 FM_ANT FM_ANTENNA Close to WCD9302 C1657 DUMMY-SHORT 0201 DUMMY_C_0201

2014/02/26: change to 0201 size

HEADSET MIC

TP1608 *TP50*

HPH_MIC_P_2 C1611 0R/+-5% HPH_MIC_P_1 C1612 2.2nF

HPH_MIC_P 1 C3 A3 C1614 ESD1605 A3 33pF C3 IP4049CX5/LF R1623 B2 2.2K/+-1% B2 C1 A1

A1 HPH_MIC_M_2 HPH_MIC_M_1 HPH_MIC_M C1 C1615 0R/+-5% C1616 5.9K/+-1%

C1618 R1626 33pF 2.2K/+-1%

MIC_BIAS2

Close to WCD9302

Motorola Mobility Confidential Restricted: May 27, 2014 Page 48 Do not share without consent from Motorola Debug Procedure: Headset

• At built level: • Check the pins on the headset jack for any bent pins or missing pins.

• On the PCB: • Checking if any open happened on the earpiece speaker series components. • Checking if any short to ground happened in the shunt components

Motorola Mobility Confidential Restricted: May 27, 2014 Page 49 Do not share without consent from Motorola Key TROUBLESHOOTING

Motorola Mobility Confidential Restricted: May 27, 2014 Page 50 Do not share without consent from Motorola PWR KEY PM_RESIN_N R2001 TP2001 *TP50* DUMMY_R_0201 SW2001 R2002 200R/+-1% PWR_KEY_CON 1 3 PHONE_ON_N 1 1 1' 2 ESD2001 2 4 2 2 2' C2001 PESD5V0U1BL EVPANDE1A 1 DUMMY_C_0201 1

VREG_L6_1P8 VOLUME UP

R2005 47K/+-5% 0201_m03 TP2004 *TP50* SW2002 1 3

KB_VOL_UP 1 1 1' 2 ESD2002 2 4 2 2 2' PESD5V0U1BL EVPANDE1A 1 1

VREG_L6_1P8 VOLUME DOWN

R2006 100K/+-5% TP2005 *TP50* SW2003 1 3

KB_VOL_DOWN 1 1 1' 2 ESD2005 2 4 2 2 2' PESD5V0U1BL EVPANDE1A 1 1

Motorola Mobility Confidential Restricted: May 27, 2014 Page 51 Do not share without consent from Motorola Debug Procedure

• At built level: • Check the pins on the keys for any bent or missing pins.

• On the PCB: • Checking if any open happened on the key series components. • Checking if any short to ground happened in the shunt components

Motorola Mobility Confidential Restricted: May 27, 2014 Page 52 Do not share without consent from Motorola WCDMA / GSM TROUBLESHOOTING

Motorola Mobility Confidential Restricted: May 27, 2014 Page 53 Do not share without consent from Motorola UMTS DTV BLOCK DIAGRAM

Motorola Mobility Confidential Restricted: May 27, 2014 Page 54 Do not share without consent from Motorola UMTS DS/SS BLOCK DIAGRAM

Motorola Mobility Confidential Restricted: May 27, 2014 Page 55 Do not share without consent from Motorola UMTS AWS BLOCK DIAGRAM

Motorola Mobility Confidential Restricted: May 27, 2014 Page 56 Do not share without consent from Motorola WCDMA/GSM RADIO CHECK

Motorola Mobility Confidential Restricted: May 27, 2014 Page 57 Do not share without consent from Motorola TXM Schematic

TXM voltage

GSM HB Rx SAW GSM HB LNA matching of WTR2605

TXM front end matching

TXM voltage

Motorola Mobility Confidential Restricted: May 27, 2014 Page 58 Do not share without consent from Motorola WCDMA B1 Tx and Rx

Motorola Mobility Confidential Restricted: May 27, 2014 Page 59 Do not share without consent from Motorola WCDMA B1 TX Check Chart – No TX

START

CHECK & REPLACE WTR2605 FAIL R2201,R2204,R2206,R2208,R2210,R2212,R2213,R220 Voltage 7,R2202,R2203,R2205,L2201,R2209,R2211,R2214,R2 CHECK ? 215

OK

TX VOLTAGE FAIL CHECK? CHECK & REPLACE C2701,C2702,C2703

OK

PA MODE & FAIL MATCH CHECK & REPLACE CHECK? C2715,C2710,R2701,L2701,U2701

OK

DUPLEXER & FAIL CHECK & REPLACE TXM U2702,C2713,L2704,C2608,C2601,C2625,U2603,C2629 CHECK ? U2601 OK

RF FAIL CONNECTOR CHECK & REPLACE CHECK ? CON2601 OK

FAIL TX LEVEL 2 Go to TX CHECK CHART- Low TX CHECK ? OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 60 Do not share without consent from Motorola WCDMA B1 TX Check Chart – Low TX

2

OK

WTR2605 FAIL CHECK & REPLACE TX Level R2701 CHECK ? PDM = 82 (set same PDM count and compare Tx power level with a good unit)

OK

CHECK & REPLACE PA GAIN & DPX FAIL R2701,U2701,L2701,U2702,C2713,L2704 LOSS PAM Gain = 26 dB in high gain mode CHECK ? DPX Loss = 1.5~3 dB

OK

FAIL TXM LOSS CHECK & REPLACE CHECK ? L2704,C2625,U2603,U2601,C2629

OK

RF FAIL CONNECTOR CHECK & REPLACE CON2601 CHECK

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 61 Do not share without consent from Motorola WCDMA B1 RX Check Chart

START

XO CHECK & REPLACE FAIL C2306,C2308 Frequency CHECK ? XO Frequency = 19.2 MHz

OK

WTR2605 CHECK & REPLACE FAIL R2201,R2204,R2206,R2208,R2210,R2212,R2213,R220 Voltage CHECK ? 7,R2202,R2203,R2205,L2201,R2209,R2211,R2214,R2 215

OK

FAIL CHECK & REPLACE DPX U2702,C2713,L2704 MATCHING

CHECK ?

FAIL OK

TXM&RF FAIL CONNECTOROK CHECK ? CHECK & REPLACE U2601,C2625,U2603,C2629,C2608,C2601,CON2601 OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 62 Do not share without consent from Motorola B1 TRX Circuits (PA + DPX )

PA voltage Input Matching for LNA of WTR2605

DUP

PA Input match for PA Output match for PA

Matching for duplexer antenna port

Motorola Mobility Confidential Restricted: May 27, 2014 Page 63 Do not share without consent from Motorola B1 TRX Circuits (WTR + PA + DPX + TXM) Layout

WTR0_PA_ON_B1 WTR0_PA_R0

B1 PA output matching

Matching for DP Ant port WTR2605 B1 DPX

TXM matching for Connector

WTR2605 LNA input matching

ANT CON

Motorola Mobility Confidential Restricted: May 27, 2014 Page 64 Do not share without consent from Motorola WCDMA B2 TX Check Chart – No TX

START

CHECK & REPLACE WTR2605 FAIL R2201,R2204,R2206,R2208,R2210,R2212,R2213,R220 Voltage 7,R2202,R2203,R2205,L2201,R2209,R2211,R2214,R2 CHECK ? 215

OK

TX VOLTAGE FAIL CHECK? CHECK & REPLACE C2801,C2802,C2803

OK

PA MODE & FAIL MATCH CHECK & REPLACE CHECK? C2819,C2811,C2809,L2801,U2801

OK

DUPLEXER & FAIL SP10T CHECK & REPLACE CHECK ? U2802,C2812,L2804,C2601,C2608,C2625,U2601 OK

RF FAIL CONNECTOR CHECK & REPLACE CHECK ? CON2601 OK

FAIL TX LEVEL 2 Go to TX CHECK CHART- Low TX CHECK ? OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 65 Do not share without consent from Motorola WCDMA B2 TX Check Chart – Low TX

2

OK

WTR2605 FAIL CHECK & REPLACE TX Level R2801 CHECK ? PDM = 82 (set same PDM count and compare Tx power level with a good unit)

OK

CHECK & REPLACE PA GAIN & DPX FAIL R2801,C2809,C2810,C2801,C2803,L2801, LOSS U2802,L2804,C2812 CHECK ? PA Gain = 26~30 dB in high gain mode DPX Loss = 2.1~2.9 dB

OK

FAIL TXM LOSS CHECK & REPLACE CHECK ? L2804,U2601,C2625,U2603,C2629

OK

RF FAIL CONNECTOR CHECK & REPLACE C2601 CHECK

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 66 Do not share without consent from Motorola WCDMA B2 RX Check Chart

START

CHECK & REPLACE XO FAIL Frequency C2306,C2308 CHECK ? XO Frequency = 19.2 MHz

OK

WTR2605 CHECK & REPLACE FAIL R2201,R2204,R2206,R2208,R2210,R2212,R2213,R220 Voltage CHECK ? 7,R2202,R2203,R2205,L2201,R2209,R2211,R2214,R2 215

OK

FAIL CHECK & REPLACE DPX & U2802,L2804,C2812 MATCHING

CHECK ?

OK

RF CON. FAIL CHECK & REPLACE &TXM U2601,C2625,U2603,C2629,C2608,C2601,CON2601 CHECKOK ?

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 67 Do not share without consent from Motorola B2 TRX Circuits (PA + DPX)

Input match for PA PA voltage PA voltage

DUP

Input Matching for LNA Output match for PA of WTR2605 Matching for DPX antenna port

Motorola Mobility Confidential Restricted: May 27, 2014 Page 68 Do not share without consent from Motorola B2 TRX Circuits (WTR + PA + DPX + TXM) Layout WTR0_PA_R0

WTR0_PA_ON_B2

PA output matching

Matching for TXM antenna port

Input Matching for DPX matching LNA of WTR2605

ANT CON Motorola Mobility Confidential Restricted: May 27, 2014 Page 69 Do not share without consent from Motorola WCDMA B4 Tx and Rx

Motorola Mobility Confidential Restricted: May 27, 2014 Page 70 Do not share without consent from Motorola WCDMA B4 Tx Check Chart – No TX

START

CHECK & REPLACE WTR2605 R2201,R2204,R2206,R2208,R2210,R2212,R2213,R220F Voltage AIL 7,R2202,R2203,R2205,L2201,R2209,R2211,R2214,R2 CHECK ? 215

O K

TX VOLTAGE F CHECK? AIL CHECK & REPLACE C2724,C2725,C2723

O K PA MODE & F CHECK & REPLACE MATCH AIL CHECK? C2716,R2706,C2724,C2725,C2715,C261 7,C2618,U2705,C2726,C2704 O K DUPLEXER & F CHECK & REPLACE TXM AIL U2702,L2704,C2713,C2601,C2608,C2625,U CHECK ? 2601,U2603,C2629 O K

RF F CONNECTOR AIL CHECK & REPLACE CHECK ? CON2601 O K F TX LEVEL 2 Go to TX CHECK CHART- Low TX CHECK ? AIL O K END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 71 Do not share without consent from Motorola WCDMA B4 Tx Check Chart – Low TX

2

O K

WTR2605 FCHECK & REPLACE TX Level AIL C2176,R2706 CHECK ? PDM = 79 (set same PDM count and compare Tx power level with a good unit)

O K

CHECK & REPLACE PA GAIN & DPX FUC2716,R2706,C2724,C2725,C2715,C2617,C2618,U2 AIL LOSS 705,C2726,C2704,U2702,L2704,C2713 CHECK ? PAM Gain = 26~30 dB in high gain mode DPX Loss = 1.5~2 dB

O K

TXM LOSS F AIL CHECK & REPLACE CHECK ? L2704,C2625,U2601,U2603,C2629

O K

RF F CONNECTOR AIL CHECK & REPLACE CON2601 CHECK

O K END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 72 Do not share without consent from Motorola WCDMA B4 RX Check Chart

START

XO CHECK & REPLACE F C2306,C2308 Frequency AIL CHECK ? XO Frequency = 19.2 MHz

O K WTR2605 CHECK & REPLACE F R2201,R2204,R2206,R2208,R2210,R2212,R2213,R220 Voltage AIL CHECK ? 7,R2202,R2203,R2205,L2201,R2209,R2211,R2214,R2 215

O K

F CHECK & REPLACE DPX & AIL U2702,L2704,C2713 MATCHING CHECK ?

O K

RF CON.& F CHECK & REPLACE TXM CHECK ? AIL U2601,C2625,U2603,C2629,C2608,C2601,CON2601 O K

O K END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 73 Do not share without consent from Motorola WCDMA B4 TX AND RX

B4 LNA Matching B4 Duplexer& Tx Matching

B4 TX WTR Output

B4 RX B4 Duplexer WTR Input Antenna Port

PA voltage

B4 PA output Matching

PA input matching U2705 ( B4 PA )

Motorola Mobility Confidential Restricted: May 27, 2014 Page 74 Do not share without consent from Motorola WCDMA B4 TRX LAYOUT (WTR + PA + DPX +TXM) WTR0_PA_ON_B1

Output match for PA

WTR0_PA_R0 WTR0_PA_R1

Matching for TXM antenna WTR2605 port

B4 DPX& Matching Input Matching for LNA of WTR2605

Motorola Mobility ANTConfidential CON Restricted: May 27, 2014 Page 75 Do not share without consent from Motorola WCDMA B5 Tx and Rx

Motorola Mobility Confidential Restricted: May 27, 2014 Page 76 Do not share without consent from Motorola WCDMA B5 TX Check Chart – No TX

START

CHECK & REPLACE WTR2605 FAIL R2201,R2204,R2206,R2208,R2210,R2212,R2213,R220 Voltage 7,R2202,R2203,R2205,L2201,R2209,R2211,R2214,R2 CHECK ? 215

OK

TX VOLTAGE FAIL CHECK? CHECK & REPLACE C2801,C2802,C2803

OK

PA MODE & FAIL MATCH CHECK & REPLACE CHECK? R2801,C2809,C2810,C2801,C2803,L2801

OK

DUPLEXER & FAIL CHECK & REPLACE TXM U2802,L2804,C2812,C2601,C2608,C2625,U2601,U2603,C2629 CHECK ?

OK FAIL RF CONNECTOR CHECK & REPLACE CHECK ? CON2601 OK

FAIL TX LEVEL 2 Go to TX CHECK CHART- Low TX CHECK ? OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 77 Do not share without consent from Motorola WCDMA B5 TX Check Chart – Low TX

2

OK

WTR2605 FAIL CHECK & REPLACE TX Level R2801 CHECK ? PDM = 80 (set same PDM count and compare Tx power level with a good unit)

OK

CHECK & REPLACE PA GAIN & DPX FAIL R2801,C2809,C2810,C2801,C2803,L2805, LOSS U2803,R2805,C2818 CHECK ? PA Gain = 26~30 dB in high gain mode DPX Loss = 2.0~3.5 dB

OK

FAIL TXM LOSS CHECK & REPLACE CHECK ? L2805,C2625,U2601,U2603,C2629

OK

RF FAIL CONNECTOR CHECK & REPLACE CON2601 CHECK

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 78 Do not share without consent from Motorola WCDMA B5 RX Check Chart

START

CHECK & REPLACE XO FAIL Frequency C2306,C2308 CHECK ? XO Frequency = 19.2 MHz

OK

WTR2605 CHECK & REPLACE FAIL R2201,R2204,R2206,R2208,R2210,R2212,R2213,R220 Voltage CHECK ? 7,R2202,R2203,R2205,L2201,R2209,R2211,R2214,R2 215

OK

FAIL CHECK & REPLACE DPX & U2803,R2805,C2818 MATCHING

CHECK ?

OK

TXM FAIL CHECK & REPLACE RF CON. C2601,C2608,C2625,U2601,U2603,C2629,CON2601 CHECKOK ?

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 79 Do not share without consent from Motorola B5 TRX Circuits (PA + DPX )

PA voltage

Input match for PA PA voltage

PA Output matching Input Matching for LNA of WTR2605 DUP

Matching for duplexer antenna port

Motorola Mobility Confidential Restricted: May 27, 2014 Page 80 Do not share without consent from Motorola B5 TRX Circuits (WTR + PA + DPX + TXM) Layout Input match WTR0_PA_ON_B5 for PA

WTR0_PA_R0

Output match for PA

Input Matching for LNA of WTR2605

DPX matching for ANT port

Matching for TXM antenna port

Motorola Mobility Confidential Restricted: May 27, 2014 Page 81 Do notANT share CON without consent from Motorola WCDMA B8 Tx and Rx

Motorola Mobility Confidential Restricted: May 27, 2014 Page 82 Do not share without consent from Motorola WCDMA B8 TX Check Chart – No TX

START

WTR2605 CHECK & REPLACE Voltage FAIL R2201,R2204,R2206,R2208,R2210,R2212,R2213,R220 CHECK ? 7,R2202,R2203,R2205,L2201,R2209,R2211,R2214,R2 215

OK

TX VOLTAGE FAIL CHECK? CHECK & REPLACE C2701,C2702,C2703

OK

PA MODE & FAIL MATCH CHECK & REPLACE CHECK? C2715,C2714,R2701,L2705,U2701

OK

DUPLEXER & FAIL CHECK & REPLACE TXM U2703,C2719,L2706,C2608,C2601,C2625,U2603,C2629 CHECK ? U2601 OK

RF FAIL CONNECTOR CHECK & REPLACE CHECK ? C2601 OK

FAIL TX LEVEL 2 Go to TX CHECK CHART- Low TX CHECK ? OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 83 Do not share without consent from Motorola WCDMA B8 TX Check Chart – Low TX

2

OK

WTR2605 FAIL CHECK & REPLACE TX Level R2701 CHECK ? PDM = 80 (set same PDM count and compare Tx power level with a good unit)

OK

CHECK & REPLACE PA GAIN & DPX FAIL R2701,U2701,L2705,L2703,C2719,L2706 LOSS PA Gain = 26~30 dB in high gain mode CHECK ? DPX Loss = 2.1~3.2

OK

FAIL TXM LOSS CHECK & REPLACE CHECK ? C2719,C2625,U2601,U2603,C2629

OK

RF FAIL CONNECTOR CHECK & REPLACE CON2601 CHECK

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 84 Do not share without consent from Motorola WCDMA B8 RX Check Chart

START

XO CHECK & REPLACE Frequency FAIL C2306,C2308 CHECK ? XO Frequency = 19.2 MHz

OK

WTR2605 CHECK & REPLACE Voltage FAIL R2201,R2204,R2206,R2208,R2210,R2212,R2213,R220 CHECK ? 7,R2202,R2203,R2205,L2201,R2209,R2211,R2214,R2 215

OK

FAIL CHECK & REPLACE DPX & U2703,L2706,C2719 MATCHING CHECK ?

OK

TXM, FAIL CHECK & REPLACE RF CON. C2601,C2608,C2625,U2601,U2603,C2629,CON2601 CHECKOK ?

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 85 Do not share without consent from Motorola B8 TRX Circuits (PA + DPX )

PA voltage

PA

Output match for PA Input match for PA DUP

Input Matching for LNA of Matching for duplexer WTR2605 antenna port

Motorola Mobility Confidential Restricted: May 27, 2014 Page 86 Do not share without consent from Motorola B8 TRX Circuits (WTR + PA + DPX + TXM) Layout WTR0_PA_ON_B8

WTR0_PA_R0

B8 PA output matching

B8 DPX

Matching for DP Ant port WTR2605

TXM matching for Connector

matching for DPX WTR2605 LNA input matching

ANT CON Motorola Mobility Confidential Restricted: May 27, 2014 Page 87 Do not share without consent from Motorola GSM Quad Band Rx

Motorola Mobility Confidential Restricted: May 27, 2014 Page 88 Do not share without consent from Motorola WCDMA/CDMA/GSM RADIO CHECK

Motorola Mobility Confidential Restricted: May 27, 2014 Page 89 Do not share without consent from Motorola GSM850 Receiver UMTS Global & AWS Check Chart

START

XO CHECK & REPLACE FAIL C2306, C2307 Frequency CHECK ? XO Freq = 19.2 MHz

OK

WTR2605 CHECK & REPLACE FAIL C2201, C2205, C2209, C2212 Voltage CHECK ?

OK

FAIL CHECK & REPLACE DPX C2807, C2813, C2817, C2818, L2806, L2807, MATCHING R2805, U2803 CHECK ?

OK

CHECK & REPLACE SP10T, FAIL C2602, C2612, C2625, C2626,C2628, C2629, RF CON. CON2601, R2602, U2601, U2603 CHECK ? OK

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 90 Do not share without consent from Motorola GSM850 Receiver Circuitry-UMTS Global & AWS

FDD B26( B5)/ BC10 TRX Please close to WTR L2806 C2813 C2817 L2805 15nH B5_PA_out_1 WTR0_PRX_LB2_1 WTR0_PRX_LB2_2 WTR0_PRX_LB2_3 10pF WTR0_PRX_LB2 3 2 1 C2815 U2803 100pF 33pF TX C2814 RX SAYFH831MBA0F0AR05 L2807 12nH GND1 9 4 GND6 8 DUMMY_C_0402 GND2 GND5 DUMMY_C_0201 GND3 ANT GND4

5 6 7 R2805 9.1nH WTR0_TRX_B5_1 WTR0_TRX_B5 C2807

C2818 4.7pF

VPH_PWR DUMMY_C_0201

WTR0_TRX_B8 WTR0_TRX_B5 WTR0_TRX_B1 WTR0_TRX_B2 R2601 C2601 C2602 22pF WTR0_PDET_IN DUMMY_R_0402 DUMMY_C_0603 U2602 5 1842.5/1960MHz

33 32 31 30 29 28 27 26 25 24 23 22 U2601 C2603 (1842.5MHz)

GSM_RX_DCS 3nH GSM_RX_DCS_1 6 GND 4 Input GND

NC Please close to WTR

GND GND GND GND GND GND 7 3 TRX4 TRX3 TRX2 TRX1

34 VBATT 21 GND GND 35 NC SPDT_OUT 20 8 2

WTR0_TXM_CTL0 C2604 L2602 (1842.5/1960MHz) L2601 C2607 36 SPDT RX2 19 ANT0_CPL 2.7nH GND (1960MHz) GND 4.3nH 37 RF_IN SPDT_IN 18 GSM_RX_PCS GSM_RX_PCS_1 9 1WTR0_PRX_MB3_1 WTR0_PRX_MB3_2 WTR0_PRX_MB3_3 38 SW1 RX1 17 Input Output WTR0_PRX_MB3 C2605 39 SW0 GND 16

40 HB_EN GND 15 P_ANT GND 33pF 33pF DUMMY_C_0201 41 LB_EN ANT 14 C2630 L2603 MODE0 GND 42 13 1pF 10 43 MODE1 GND C2631 GND 1.2pF DUMMY_C_0201 GND GND GND VCC VCC GND GND GND GND GND GND GND SKY77573-21 1 2 3 4 5 6 7 8 9 10 11 12 WTR0_RF_TX_DA_1 VPH_PWR C2625 P_ANT_1 WTR0_TXM_CTL1 3nH

WTR0_TXM_CTL2 C2614 C2610 C2612 C2608 C2626 C2611 0.5pF C2609 100pF 4.7uF 0.1uF DUMMY_C_0201 DUMMY_C_0201 C2613 DUMMY_C_0603 DUMMY_C_0201

CON2601 CON2602 MM8030-2610RK0 3 KMC1001-F016-7F 3 C2629 WTR0_TXM_CTL3 3 3.4nH 2 4 P_ANT_4 2 1 P_ANT_3 P_ANT_2 WTR0_TXM_CTL4 2 signal OUT GND1 IN 1 2 3

WTR0_PA_R0 1 C2627 U2603 GND2 IN HHM22106B1 1 C2628 OUT GND1 WTR0_PA_R1 4 DUMMY_C_0201 0.5pF

C2617 C2618 C2619 C2620 50ohm terminate GND2 COUPLING DUMMY_C_0201 DUMMY_C_0201DUMMY_C_0201 DUMMY_C_0201 6 5 4

R2602 ANT0_CPL Motorola Mobility Confidential Restricted: May 27, 2014 51R/+-1% Page 91 Do not share without consent from Motorola GSM850 Receiver Circuitry-UMTS Global & AWS

DPX

WTR2605 TXM

Motorola Mobility Confidential Restricted: May 27, 2014 Page 92 Do not share without consent from Motorola GSM900 Receiver UMTS Global Check Chart

START

XO CHECK & REPLACE FAIL C2306, C2307 Frequency CHECK ? XO Freq = 19.2 MHz

OK

WTR2605 CHECK & REPLACE FAIL C2201, C2205, C2209, C2212 Voltage CHECK ?

OK

FAIL CHECK & REPLACE DPX C2719, C2721, C2728, C2732, L2706, L2707, U2703 MATCHING

CHECK ?

OK

CHECK & REPLACE SP10T, FAIL C2602, C2612, C2625, C2626,C2628, C2629, RF CON. CON2601, R2602, U2601, U2603 CHECK ? OK

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 93 Do not share without consent from Motorola B8 GSM900 ReceiverB8_PA_out_1 Circuitry-UMTS Global

U2703 D5PF942M5M3G6MZ 3 2 1 Tx Rx

GND 9 4 GND 8 WTR0_PRX_LB1_1 GND GND GND ANT GND 5 6 7

WTR0_TRX_B8_1

C2719

WTR0_TRX_B8

L2706 33pF 5.6nH C2721 Please close to WTR 33pF C2722 L2707 WTR0_RX_G900_3 WTR0_PRX_LB1_2 C2720 WTR0_PRX_LB1

DUMMY_C_0201 12nH C2728 DUMMY_C_0201 DUMMY_C_0201 C2727 DUMMY_C_0201 WTR0_RX_G900_1 U2706 5 4 C2732 DUMMY_C_0201 GND

1 UNBAL Port UNBAL Port

GND GND GSM 900 RX 942.5MHz 2 3

VPH_PWR

WTR0_TRX_B8 WTR0_TRX_B5 WTR0_TRX_B1 WTR0_TRX_B2 R2601 C2601 C2602 22pF WTR0_PDET_IN DUMMY_R_0402 DUMMY_C_0603 U2602 5 1842.5/1960MHz

33 32 31 30 29 28 27 26 25 24 23 22 U2601 C2603 (1842.5MHz)

GSM_RX_DCS 3nH GSM_RX_DCS_1 6 GND 4 Input GND

NC Please close to WTR

GND GND GND GND GND GND 7 3 TRX4 TRX3 TRX2 TRX1

34 VBATT 21 GND GND 35 NC SPDT_OUT 20 8 2

WTR0_TXM_CTL0 C2604 L2602 (1842.5/1960MHz) L2601 C2607 36 SPDT RX2 19 ANT0_CPL 2.7nH GND (1960MHz) GND 4.3nH 37 RF_IN SPDT_IN 18 GSM_RX_PCS GSM_RX_PCS_1 9 1WTR0_PRX_MB3_1 WTR0_PRX_MB3_2 WTR0_PRX_MB3_3 38 SW1 RX1 17 Input Output WTR0_PRX_MB3 C2605 39 SW0 GND 16

40 HB_EN GND 15 P_ANT GND 33pF 33pF DUMMY_C_0201 41 LB_EN ANT 14 C2630 L2603 MODE0 GND 42 13 1pF 10 43 MODE1 GND C2631 GND 1.2pF DUMMY_C_0201 GND GND GND VCC VCC GND GND GND GND GND GND GND SKY77573-21 1 2 3 4 5 6 7 8 9 10 11 12 WTR0_RF_TX_DA_1 VPH_PWR C2625 P_ANT_1 WTR0_TXM_CTL1 3nH

WTR0_TXM_CTL2 C2614 C2610 C2612 C2608 C2626 C2611 0.5pF C2609 100pF 4.7uF 0.1uF DUMMY_C_0201 DUMMY_C_0201 C2613 DUMMY_C_0603 DUMMY_C_0201

CON2601 CON2602 MM8030-2610RK0 3 KMC1001-F016-7F 3 C2629 WTR0_TXM_CTL3 3 3.4nH 2 4 P_ANT_4 2 1 P_ANT_3 P_ANT_2 WTR0_TXM_CTL4 2 signal OUT GND1 IN 1 2 3

WTR0_PA_R0 1 C2627 U2603 GND2 IN HHM22106B1 1 C2628 OUT GND1 WTR0_PA_R1 4 DUMMY_C_0201 0.5pF

C2617 C2618 C2619 C2620 50ohm terminate GND2 COUPLING DUMMY_C_0201 DUMMY_C_0201DUMMY_C_0201 DUMMY_C_0201 Motorola Mobility Confidential Restricted: May 27, 2014 6 5 4 Page 94 R2602 Do not share without consent from Motorola ANT0_CPL 51R/+-1% GSM900 Receiver Circuitry-UMTS Global

DPX

WTR2605 TXM

Motorola Mobility Confidential Restricted: May 27, 2014 Page 95 Do not share without consent from Motorola GSM900 Receiver UMTS AWS Check Chart

START

XO CHECK & REPLACE FAIL C2306, C2307 Frequency CHECK ? XO Freq = 19.2 MHz

OK

WTR2605 CHECK & REPLACE FAIL C2201, C2205, C2209, C2212 Voltage CHECK ?

OK

FAIL CHECK & REPLACE SAW C2720, C2722, L2707, U2706 MATCHING

CHECK ?

OK

SP10T, FAIL CHECK & REPLACE RF CON. C2602, C2612, C2625, C2626,C2628, C2629, CHECKOK ? CON2601, R2602, U2601, U2603

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 96 Do not share without consent from Motorola L2705 B8_PA_out_1 B8 2.7nH C2717

U2703 D5PF942M5M3G6MZ 3 2 1 Tx DUMMY_C_0402 Rx

GND 9 4 GND 8 WTR0_PRX_LB1_1 GND GND GND ANT GND 5 6 7

GSM900 Receiver Circuitry-UMTSWTR0_TRX_B8_1 AWS C2719

WTR0_TRX_B8

L2706 10pF 7.5nH

VCC_APT C2721 Please close to WTR 33pF C2722 L2707 WTR0_RX_G900_3 WTR0_PRX_LB1_2 C2720 WTR0_PRX_LB1 C2723 C2725 22pF 2.2uF 33pF 12nH C2728 33pF C2726 DUMMY_C_0201 B4_PA_out B4_PA_out_1 C2727 2.7nH DUMMY_C_0201 L2709 L2708 5.6nH 1.5pF WTR0_RX_G900_1 U2706 5 4 C2732 DUMMY_C_0201 GND

1 UNBAL Port UNBAL Port

GND GND GSM 900 RX 942.5MHz 2 3

VPH_PWR

WTR0_TRX_B8 WTR0_TRX_B5 WTR0_TRX_B1 WTR0_TRX_B2 R2601 C2601 C2602 22pF WTR0_PDET_IN DUMMY_R_0402 DUMMY_C_0603 U2602 5 1842.5/1960MHz

33 32 31 30 29 28 27 26 25 24 23 22 U2601 C2603 (1842.5MHz)

GSM_RX_DCS 3nH GSM_RX_DCS_1 6 GND 4 Input GND

NC Please close to WTR

GND GND GND GND GND GND 7 3 TRX4 TRX3 TRX2 TRX1

34 VBATT 21 GND GND 35 NC SPDT_OUT 20 8 2

WTR0_TXM_CTL0 C2604 L2602 (1842.5/1960MHz) L2601 C2607 36 SPDT RX2 19 ANT0_CPL 2.7nH GND (1960MHz) GND 4.3nH 37 RF_IN SPDT_IN 18 GSM_RX_PCS GSM_RX_PCS_1 9 1WTR0_PRX_MB3_1 WTR0_PRX_MB3_2 WTR0_PRX_MB3_3 38 SW1 RX1 17 Input Output WTR0_PRX_MB3 C2605 39 SW0 GND 16

40 HB_EN GND 15 P_ANT GND 33pF 33pF DUMMY_C_0201 41 LB_EN ANT 14 C2630 L2603 MODE0 GND 42 13 1pF 10 43 MODE1 GND C2631 GND 1.2pF DUMMY_C_0201 GND GND GND VCC VCC GND GND GND GND GND GND GND SKY77573-21 1 2 3 4 5 6 7 8 9 10 11 12 WTR0_RF_TX_DA_1 VPH_PWR C2625 P_ANT_1 WTR0_TXM_CTL1 3nH

WTR0_TXM_CTL2 C2614 C2610 C2612 C2608 C2626 C2611 0.5pF C2609 100pF 4.7uF 0.1uF DUMMY_C_0201 DUMMY_C_0201 C2613 DUMMY_C_0603 DUMMY_C_0201

CON2601 CON2602 MM8030-2610RK0 3 KMC1001-F016-7F 3 C2629 WTR0_TXM_CTL3 3 3.4nH 2 4 P_ANT_4 2 1 P_ANT_3 P_ANT_2 WTR0_TXM_CTL4 2 signal OUT GND1 IN 1 2 3

WTR0_PA_R0 1 C2627 U2603 GND2 IN HHM22106B1 1 C2628 OUT GND1 WTR0_PA_R1 4 DUMMY_C_0201 0.5pF

C2617 C2618 C2619 C2620 50ohm terminate GND2 COUPLING DUMMY_C_0201 DUMMY_C_0201DUMMY_C_0201 DUMMY_C_0201 6 5 4

R2602 ANT0_CPL Motorola Mobility Confidential Restricted: May 27, 2014 51R/+-1% Page 97 Do not share without consent from Motorola GSM900 Receiver Circuitry-UMTS AWS

TXM SAW

WTR2605

Motorola Mobility Confidential Restricted: May 27, 2014 Page 98 Do not share without consent from Motorola GSM1800 Receiver UMTS Global & AWS Check Chart

START

XO CHECK & REPLACE FAIL C2306, C2307 Frequency CHECK ? XO Freq = 19.2 MHz

OK

WTR2605 CHECK & REPLACE FAIL C2201, C2205, C2209, C2212 Voltage CHECK ?

OK

FAIL CHECK & REPLACE SAW C2603, C2607, C2631, L2601, L2602, L2603, U2602 MATCHING

CHECK ?

OK

SP10T, FAIL CHECK & REPLACE RF CON. C2602, C2612, C2625, C2626,C2628, C2629, CHECKOK ? CON2601, R2602, U2601, U2603

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 99 Do not share without consent from Motorola GSM1800 Receiver Circuitry-UMTS Global & AWS

VPH_PWR

WTR0_TRX_B8 WTR0_TRX_B5 WTR0_TRX_B1 WTR0_TRX_B2 R2601 C2601 C2602 22pF WTR0_PDET_IN DUMMY_R_0402 DUMMY_C_0603 U2602 5 1842.5/1960MHz

33 32 31 30 29 28 27 26 25 24 23 22 U2601 C2603 (1842.5MHz)

GSM_RX_DCS 3nH GSM_RX_DCS_1 6 GND 4 Input GND

NC Please close to WTR

GND GND GND GND GND GND 7 3 TRX4 TRX3 TRX2 TRX1

34 VBATT 21 GND GND

35 NC SPDT_OUT 20 C2604 8 2 L2602

(1842.5/1960MHz) L2601 C2607 36 SPDT RX2 19 ANT0_CPL 2.7nH GND (1960MHz) GND 4.3nH 37 RF_IN SPDT_IN 18 GSM_RX_PCS GSM_RX_PCS_1 9 1WTR0_PRX_MB3_1 WTR0_PRX_MB3_2 WTR0_PRX_MB3_3 38 SW1 RX1 17 Input Output WTR0_PRX_MB3 C2605 39 SW0 GND 16

40 HB_EN GND 15 P_ANT GND 33pF 33pF DUMMY_C_0201 41 LB_EN ANT 14 C2630 L2603 MODE0 GND 42 13 1pF 10 43 MODE1 GND C2631 GND 1.2pF DUMMY_C_0201 GND GND GND VCC VCC GND GND GND GND GND GND GND SKY77573-21 1 2 3 4 5 6 7 8 9 10 11 12

VPH_PWR

C2610 C2612 C2608 C2625 C2611 3nH P_ANT_1 100pF 4.7uF 0.1uF C2613 DUMMY_C_0603 DUMMY_C_0201 C2614 C2626 0.5pF DUMMY_C_0201

CON2601 CON2602 MM8030-2610RK0 3 KMC1001-F016-7F 3 C2629 3 3.4nH 2 4 P_ANT_4 2 1 P_ANT_3 P_ANT_2 2 signal OUT GND1 IN 1 2 3

1 C2627 U2603

C2618 C2619 C2620 GND2 IN HHM22106B1 1 C2628 OUT GND1 4 DUMMY_C_0201 0.5pF DUMMY_C_0201DUMMY_C_0201 DUMMY_C_0201 50ohm terminate GND2 COUPLING 6 5 4

R2602 ANT0_CPL 51R/+-1%

Thermistor place near PAs ANT2602 ANT2601 QM-12G QM-12G 1 1 1 1

Motorola Mobility Confidential Restricted: May 27, 2014 Page 100 C2621 Do not share without consent from Motorola 6.2nH GSM1800 Receiver Circuitry-UMTS Global

WTR2605 TXM

SAW

Motorola Mobility Confidential Restricted: May 27, 2014 Page 101 Do not share without consent from Motorola GSM1900 Receiver UMTS Global & AWS Check Chart

START

XO CHECK & REPLACE FAIL C2306, C2307 Frequency CHECK ? XO Freq = 19.2 MHz

OK

WTR2605 CHECK & REPLACE FAIL C2201, C2205, C2209, C2212 Voltage CHECK ?

OK

FAIL CHECK & REPLACE SAW C2604, C2607, C2630, L2601, L2602, L2603, U2602 MATCHING

CHECK ?

OK

SP10T, FAIL CHECK & REPLACE RF CON. C2602, C2612, C2625, C2626,C2628, C2629, CHECKOK ? CON2601, R2602, U2601, U2603

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 102 Do not share without consent from Motorola GSM1900 Receiver Circuitry-UMTS Global & AWS

VPH_PWR

WTR0_TRX_B8 WTR0_TRX_B5 WTR0_TRX_B1 WTR0_TRX_B2 R2601 C2601 C2602 22pF WTR0_PDET_IN DUMMY_R_0402 DUMMY_C_0603 U2602 5 1842.5/1960MHz

33 32 31 30 29 28 27 26 25 24 23 22 U2601 C2603 (1842.5MHz)

GSM_RX_DCS 3nH GSM_RX_DCS_1 6 GND 4 Input GND

NC Please close to WTR

GND GND GND GND GND GND 7 3 TRX4 TRX3 TRX2 TRX1

34 VBATT 21 GND GND

35 NC SPDT_OUT 20 C2604 8 2 L2602

(1842.5/1960MHz) L2601 C2607 36 SPDT RX2 19 ANT0_CPL 2.7nH GND (1960MHz) GND 4.3nH 37 RF_IN SPDT_IN 18 GSM_RX_PCS GSM_RX_PCS_1 9 1WTR0_PRX_MB3_1 WTR0_PRX_MB3_2 WTR0_PRX_MB3_3 38 SW1 RX1 17 Input Output WTR0_PRX_MB3 C2605 39 SW0 GND 16

40 HB_EN GND 15 P_ANT GND 33pF 33pF DUMMY_C_0201 41 LB_EN ANT 14 C2630 L2603 MODE0 GND 42 13 1pF 10 43 MODE1 GND C2631 GND 1.2pF DUMMY_C_0201 GND GND GND VCC VCC GND GND GND GND GND GND GND SKY77573-21 1 2 3 4 5 6 7 8 9 10 11 12

VPH_PWR

C2610 C2612 C2608 C2625 C2611 3nH P_ANT_1 100pF 4.7uF 0.1uF C2613 DUMMY_C_0603 DUMMY_C_0201 C2614 C2626 0.5pF DUMMY_C_0201

CON2601 CON2602 MM8030-2610RK0 3 KMC1001-F016-7F 3 C2629 3 3.4nH 2 4 P_ANT_4 2 1 P_ANT_3 P_ANT_2 2 signal OUT GND1 IN 1 2 3

1 C2627 U2603

C2618 C2619 C2620 GND2 IN HHM22106B1 1 C2628 OUT GND1 4 DUMMY_C_0201 0.5pF DUMMY_C_0201DUMMY_C_0201 DUMMY_C_0201 50ohm terminate GND2 COUPLING 6 5 4

R2602 ANT0_CPL 51R/+-1%

Thermistor place near PAs ANT2602 ANT2601 QM-12G QM-12G 1 1 1 1

Motorola Mobility Confidential Restricted: May 27, 2014 Page 103 C2621 Do not share without consent from Motorola 6.2nH GSM1900 Receiver Circuitry-UMTS Global

WTR2605 TXM

SAW

Motorola Mobility Confidential Restricted: May 27, 2014 Page 104 Do not share without consent from Motorola WCDMA B1/B2/B4/B8 and CDMA BC0/BC1/BC10 Diversity Rx

Motorola Mobility Confidential Restricted: May 27, 2014 Page 105 Do not share without consent from Motorola Diversity RX Check Chart For CDMA BC0, BC1, BC10

START

XO CHECK & REPLACE FAIL R3200,C3204 Frequency CHECK ? XO Freq = 19.2 MHz

OK CHECK & REPLACE WFR2600 FAIL R3310,C3310,C3311, R3312, C3312, R3313, C3313, Voltage R3314, C3314, R3315, C3315, R3320, C3320, C3321, CHECK ? R3300, C3300, C3301, R3302, C3302, R3303, C3303, R3304, C3304

OK

FAIL CHECK & REPLACE Antenna Con. L173, C174, L172, C173, C171, R135 Check

OK

FAIL SP4T RF CHECK & REPLACE CON. CHECK? C171, C4803,

OK

FAIL CHECK & REPLACE Matching CON. C4823, FL4820, C4821, C4822, C4824, C4819, CHECK? L4811, C4812, C4819

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 106 Do not share without consent from Motorola Diversity RX Check Chart For UMTS Global B1, B8

START

XO CHECK & REPLACE FAIL R3200,C3204 Frequency CHECK ? XO Freq = 19.2 MHz

OK CHECK & REPLACE WFR2600 FAIL R3310,C3310,C3311, R3312, C3312, R3313, C3313, Voltage R3314, C3314, R3315, C3315, R3320, C3320, C3321, CHECK ? R3300, C3300, C3301, R3302, C3302, R3303, C3303, R3304, C3304

OK

FAIL CHECK & REPLACE Antenna Con. L173, C174, L172, C173, C171, R135 Check

OK

FAIL SP4T RF CHECK & REPLACE CON. CHECK? C171, C4803, U4800

OK

FAIL CHECK & REPLACE Matching CON. C4818, FL4805, L4806, C4807, C4805, C4820, CHECK? FL4815, C4815

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 107 Do not share without consent from Motorola Diversity RX Check Chart For UMTS AWS B2, B4

START

XO CHECK & REPLACE FAIL R3200,C3204 Frequency CHECK ? XO Freq = 19.2 MHz

OK CHECK & REPLACE WFR2600 FAIL R3310,C3310,C3311, R3312, C3312, R3313, C3313, Voltage R3314, C3314, R3315, C3315, R3320, C3320, C3321, CHECK ? R3300, C3300, C3301, R3302, C3302, R3303, C3303, R3304, C3304

OK

FAIL CHECK & REPLACE Antenna Con. L173, C174, L172, C173, C171, R135 Check

OK

FAIL SP4T RF CHECK & REPLACE CON. CHECK? C171, C4803, U4800

OK

FAIL CHECK & REPLACE Matching CON. C4819, FL4810, L4811, C4812, C4819, C4818, CHECK? FL4805, L4806, C4807, C4805

OK

END

Motorola Mobility Confidential Restricted: May 27, 2014 Page 108 Do not share without consent from Motorola SP4T and Matching Circuits

SP4T Circuits Matching Circuits

Motorola Mobility Confidential Restricted: May 27, 2014 Page 109 Do not share without consent from Motorola Antenna Circuits

Motorola Mobility Confidential Restricted: May 27, 2014 Page 110 Do not share without consent from Motorola WFR2600 Voltage Supply Circuits

Motorola Mobility Confidential Restricted: May 27, 2014 Page 111 Do not share without consent from Motorola XO Supply Circuit

Motorola Mobility Confidential Restricted: May 27, 2014 Page 112 Do not share without consent from Motorola SP4T, Voltage Supply, XO, and Matching Circuits Layout

Matching Voltage Supply

XO B8

BC1/B2

BC0, BC10 B1/4

Motorola Mobility Confidential Restricted: MaySP4T 27, 2014 Page 113 Do not share without consent from Motorola Antenna Matching Circuit Layout

Motorola Mobility Confidential Restricted: May 27, 2014 Page 114 Do not share without consent from Motorola GSM Quad Band Tx

Motorola Mobility Confidential Restricted: May 27, 2014 Page 115 Do not share without consent from Motorola GSM QUAD BAND TX CHECK CHART – NO TX

QB(GSM) R2301 C2301 3.7nH WTR0_RF_TX_DA_1_1 WTR0_RF_TX_DA_1 WTR2605 WTR0

C2303 33pF DUMMY_C_0201 C2302 0.5pF

WTR0_RF_TX_DA_1_0

U2301A 7 TX1_OUT

C2304 100pF (B1/B8 or B4) 32 WTR0_RF_TX_DA_2_1 1 GND1 WTR0_RF_TX_DA_2 TX2_OUT

(B2/B5,BC0/BC1/BC10) 6 WTR0_RF_TX_DA_3 TX3_OUT

2 22 U2602 TX_BB_IP WTR0_PDET_IN 5 PDET_RFFB_IN1842.5/1960MHz 12 TX_BB_IM

33 32 31 30 29 28 27 26 25 24 23 22 U2601 (1842.5MHz) 18

6 GND 4 TX_BB_QP Input GND

NC (B8 or GSM900 RX) 5 23

GND GND GND GND GND GND WTR0_PRX_LB1 7 3

TRX4 TRX3 TRX2 TRX1 RX_LB1_IN TX_BB_QM

34 VBATT 21 GND GND

35 NC SPDT_OUT 20 C2604 8 2

(1842.5/1960MHz) L2601 36 SPDT RX2 19 ANT0_CPL 2.7nH GND (1960MHz) GND RF_IN SPDT_IN 24 37 18 GSM_RX_PCS GSM_RX_PCS_1 9 1WTR0_PRX_MB3_1 WTR0_PRX_MB3_2DAC_REF SW1 RX1 (B5) Input 10 Output 38 WTR0_PRX_LB217 RX_LB2_IN 39 SW0 GND 16

40 HB_EN GND 15 P_ANT GND 33pF 41 LB_EN ANT 14 C2630 MODE0 GND

42 13 10 1pF 36 43 MODE1 GND C2631 GND DNC1 1.2pF

GND GND GND VCC VCC GND GND GND GND GND GND GND 53 GP_DATA0 SKY77573-21 1 2 3 4 5 6 7 8 9

10 11 12 58 GP_DATA1 (B1) 4 57 WTR0_PRX_MB1 VPH_PWR RX_MB1_IN GND17

56 SSBI_TX_GNSS 9 8 C2610 C2612 C2608 RX_MB2_INC2625 SSBI_RX C2611 3nH P_ANT_1 13 100pF 4.7uF 0.1uF RF_ON DUMMY_C_0603

C2614 C26263 61 0.5pF RX_MB3_IN RX_BB_IP DUMMY_C_0201 55 RX_BB_IM 49 RX_BB_QP 43 RX_BB_QM CON2601 CON2602 MM8030-2610RK0 60 3 KMC1001-F016-7F 3 XO_IN C2629 62 3 11 3.4nH GNSS_BB_IP 2 4 P_ANT_4 2 1 P_ANT_3 GNSS_RF_INP_ANT_2 51 2 signal OUT GND1 IN GNSS_BB_IM 1 2 3 45

1 C2627 U2603 GNSS_BB_QP GND2 IN HHM22106B1 41 1 C2628 OUT GNSS_BB_QM GND1 4 DUMMY_C_0201 0.5pF WTR-2605-0-62WLNSP-TR-07-1 50ohm terminate GND2 COUPLING 6 5 4

Motorola Mobility Confidential Restricted: May 27, 2014 Page 116 Do not share without consent from Motorola QRCT GSM POWER TRANSMIT

Motorola Mobility Confidential Restricted: May 27, 2014 Page 117 Do not share without consent from Motorola QRCT GSM POWER TRANSMIT

Motorola Mobility Confidential Restricted: May 27, 2014 Page 118 Do not share without consent from Motorola QRCT GSM POWER TRANSMIT

Motorola Mobility Confidential Restricted: May 27, 2014 Page 119 Do not share without consent from Motorola WLAN / BT / FM TROUBLESHOOTING

Motorola Mobility Confidential Restricted: May 27, 2014 Page 120 Do not share without consent from Motorola Bluetooth/WiFi Power-On Failure

WLAN/BT power-on failure Symptoms: WLAN DL test firmware test commands fail Bluetooth power-on test commands fail

Motorola Mobility Confidential Restricted: May 27, 2014 Page 121 Do not share without consent from Motorola Step 1 for BT/Wi-Fi Power-On Failure

– Check if the other functionality fails as well, e.g. check WLAN “power on” if Bluetooth can not be powered on. Check Bluetooth “power on” if WLAN can not be powered on.

– Both WLAN and Bluetooth share the same IC and most of the circuit, so if one of the BT/Wi-Fi fails, the other should fail as well. If only one of them fails, it is highly likely that it is not a hardware problem and it could just that the BT/Wi-Fi is turned on through the UI already and the test commands can not turn it on again.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 122 Do not share without consent from Motorola Step 2 for BT/Wi-Fi Power-On Failure If both BT and WLAN fails, it is highly indicative of a hardware failure.

Location of the Bluetooth and WLAN circuit (Shown on the next few pages)

Check for any visible damage around the BT/WLAN antenna/IC area.

BT/Wi-Fi Antenna Schemac

Motorola Mobility Confidential Restricted: May 27, 2014 Page 123 Do not share without consent from Motorola RF & 19.2MHz TCXO Input Schematic

RF output

Motorola Mobility Confidential Restricted: May 27, 2014 Page 124 Do not share without consent from Motorola Power Supply Schematic

Motorola Mobility Confidential Restricted: May 27, 2014 Page 125 Do not share without consent from Motorola Part Placement

Motorola Mobility Confidential Restricted: May 27, 2014 Page 126 Do not share without consent from Motorola Antenna Part Placement

Motorola Mobility Confidential Restricted: May 27, 2014 Page 127 Do not share without consent from Motorola Part Placement - 1

Motorola Mobility Confidential Restricted: May 27, 2014 Page 128 Do not share without consent from Motorola Part Placement - 2

RF Components

VREG_L16_3P0 Components

VREG_L24_1P3 Components

19.2MHz TCXO Components

C3207

VREG_L10_1P8 Component

VREG_L6_1P8 Component

Motorola Mobility Confidential Restricted: May 27, 2014 Page 129 Do not share without consent from Motorola Motorola Mobility Confidential Restricted: May 27, 2014 Page 130 Do not share without consent from Motorola Step 3 for BT/Wi-Fi Power-On Failure

• If no visible damage can be seen, check for any visible damage on the IC and components. Look for misplaced or damaged components.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 131 Do not share without consent from Motorola Debugging BT / WLAN Power-Up Failure

• Check clock supplies – 19.2MHz Clock: NET RFCLK_WCN check at component C3213

• Check DC Voltages: – Typical DC voltages in WCN3620 (U3202) area • C3205, C3206, C3223, C3210, C3212, C3214, C3215, C3217, C3218, L3208, C3219 and C3220 should be 1.3V. • C3222 and C3221 should be 3.3V. • C3202 and C3204 should be 1.8V.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 132 Do not share without consent from Motorola Debugging BT / WLAN Power-Up Failure

• Check connections WCN3620 and MSM8226: – WLAN: no probing point – use x-ray or other means to make sure following is soldered properly • Pins 54, 59, 47, and 53 of U3202 (these are connection points of IQ lines) • Pins 55, 26, and 48 of U3202(these are connection points of DATA lines)

– Bluetooth: no probing point – use x-ray or other means to make sure following is soldered properly • Pins 18, 33, and 28 of U3202 (these are connection points of control, SSBI and data lines)

Motorola Mobility Confidential Restricted: May 27, 2014 Page 133 Do not share without consent from Motorola Debugging BT/WLAN Low TX Power • Probe and measure the output power at the antenna contact area and see in a spectrum analyzer if you see if the phone is transmitting any power • For WiFi, please measure the output power in FTM(PD terminal). • For BT, please measure the output power in FTM mode(PD terminal).

BT test mode command: Bluetooth Module On Bluetooth Settxmode Channel39 DH1 PRBS9 Class1

WiFi test mode command: WiFi module on WiFi setchannel 7 WiFi setdatarate 11B_LONG_11_MBPS WiFi settxpower 18 WiFi txmode on WiFi txmode off

Motorola Mobility Confidential Restricted: May 27, 2014 Page 134 Do not share without consent from Motorola Bluetooth/WiFi TX/RX RF Failure

– BT/Wi-Fi TX/RX RF failure • Symptoms: – Wi-Fi Radiated TX test value out of limits – Bluetooth radiated TX test value out of limits – Wi-Fi scan test fails – Bluetooth ping test fails

Motorola Mobility Confidential Restricted: May 27, 2014 Page 135 Do not share without consent from Motorola Step 1 for BT/Wi-Fi TX/RX RF Failure • Look for visible damage of the BT/WiFi Antenna, Antenna Contacts and BT/WiFi circuits

Motorola Mobility Confidential Restricted: May 27, 2014 Page 136 Do not share without consent from Motorola Step 2 for BT/Wi-Fi TX/RX RF Failure

– If there is no visible sign of antenna damage and antenna contacts damage, its most likely something wrong in the BT/Wi-Fi chips or circuits. – Look for misplaced or damaged RF front-end components. Please refer to the previous slide describing the layout of the WLAN circuit. – It is recommended to probe the amplitude of the TX signal along the RF path to look for the failure component.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 137 Do not share without consent from Motorola Debugging FM RSSI Failure

• If FM RSSI is out of limits Ø Check whether the headset connection between the phone and the FM signal generator are correctly done Ø Check and make sure that the headset jack is not damaged Ø Then check for any visible damage around the FM antenna/Antenna matching components Ø Check whether the FM Rx matching components placed correctly/damaged Ø Then Check connections between WCN3620 and MSM8226: – FM: no probing point – use x-ray or other means to make sure following is soldered properly • Pins 50 of U3202 (FM Rx RF line) • Pins 41 and 46 of U3202 (these are connection points of SSBI and DATA lines)

Motorola Mobility Confidential Restricted: May 27, 2014 Page 138 Do not share without consent from Motorola FM Rx Matching/WAN Filtering Components

FM Rx matching/ WAN filtering components

Motorola Mobility Confidential Restricted: May 27, 2014 Page 139 Do not share without consent from Motorola FM Part Placement/Roung

FM Antenna matching FM Rx matching/ components WAN filtering components

Motorola Mobility Confidential Restricted: May 27, 2014 Page 140 Do not share without consent from Motorola DTV TROUBLESHOOTING

Motorola Mobility Confidential Restricted: May 27, 2014 Page 141 Do not share without consent from Motorola Step 1 for DTV Power-On Failure

DTV using external antenna Check for any visible damage around the DTV area.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 142 Do not share without consent from Motorola RF & 27MHz TCXO Input Schematic

Motorola Mobility Confidential Restricted: May 27, 2014 Page 143 Do not share without consent from Motorola Power supply & BB Interface Schematic

Motorola Mobility Confidential Restricted: May 27, 2014 Page 144 Do not share without consent from Motorola Part Placement

Motorola Mobility Confidential Restricted: May 27, 2014 Page 145 Do not share without consent from Motorola Antenna Part Placement

Motorola Mobility Confidential Restricted: May 27, 2014 Page 146 Do not share without consent from Motorola Part Placement - 1

Motorola Mobility Confidential Restricted: May 27, 2014 Page 147 Do not share without consent from Motorola Part Placement - 2

RF Components

VREG_L26_1P2 Components

VREG_L6_1P8 Components

27MHz XO Components

BB interface Components

Motorola Mobility Confidential Restricted: May 27, 2014 Page 148 Do not share without consent from Motorola Motorola Mobility Confidential Restricted: May 27, 2014 Page 149 Do not share without consent from Motorola Step 3 for DTV Power-On Failure

• If no visible damage can be seen, check for any visible damage on the IC and components. Look for misplaced or damaged components.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 150 Do not share without consent from Motorola Debugging DTV Power-Up Failure

• If no visible damage can be seen, check for any visible damage on the IC and components. Look for misplaced or damaged components. • Check clock supplies – 27 MHz Clock: NET DTV_XO_P/DTV_XO_N check at component C3212/ C3313 • Check DC Voltages: – Typical DC voltages in NMI326AFB (U3302) area • L3310, C3304, and C3306 should be 1.2V. • C3311 and C3305 should be 1.8V. • Check connections NMI326AFB and MSM8226: – Make sure following is soldered properly • R3304, R3305, R3306, R3307, R3308 and R3309. (these components are connect to data and signal lines)

Motorola Mobility Confidential Restricted: May 27, 2014 Page 151 Do not share without consent from Motorola DTV RF Failure

– It is most likely something wrong in the DTV chips or circuits. – Look for misplaced or damaged RF front-end components. Please refer to the previous slide describing the layout of the DTV circuit. – It is recommended to using the signal generator and probe the amplitude of the RF signal along the RF path to look for the failure component.

Motorola Mobility Confidential Restricted: May 27, 2014 Page 152 Do not share without consent from Motorola GPS TROUBLESHOOTING

Motorola Mobility Confidential Restricted: May 27, 2014 Page 153 Do not share without consent from Motorola GPS TROUBLESHOOT FLOW CHART Start

GPS Voltage Check Check VREG_L14_2P75 and replace U1001 Ok

GPS Front/ Check and replace Inter-stage filter check U3101

Ok

External LNA gain Check and replace check (15.8 U3104 dB)

Ok

End Motorola Mobility Confidential Restricted: May 27, 2014 Page 154 Do not share without consent from Motorola GPS FRONT END BLOCK

GPS External LNA U3104 GPS front end SAW U3101

Motorola Mobility Confidential Restricted: May 27, 2014 Page 155 Do not share without consent from Motorola