1 MERCURY Villager / NISSAN Quest 1999-02 2

INSTALLATION INSTRUCTIONS FOR PART CF-710NI / IBR-710NI

APPLICATIONS INFINITI 1996-1999 I-30 MERCURY 1993-2002 Villager NISSAN 1995-1998 200SX/240SX 1998-2001 Altima / 1998-2004 Frontier 1995-2003 Maxima / 1996-2004 Pathfinder/QX4 1997-2000 1993-2003 Quest / 1995-1999 Sentra 2000-2004 Xterra CF-710NI / IBR-710NI KIT FEATURES • DDIN Head Unit Provision • Stacked ISO DIN Head Unit Provision • ISO and DIN Provisions • Pocket (holds 2 jewel cases) KIT COMPONENTS A) DDIN Trim plate B) DDIN Brackets C) Radio Housing D) (4) Phillips Pan Head Screws E) Iso Trim Plate F) Bracket Set#1 G) Bracket Set #2 H) ISO Brackets I) Bracket Set #3

A B C D E

F G H I TOOLS REQUIRED: Cutting Tool • Phillips Screwdriver • Socket Wrench

METRA. The World’s Best Kits. 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004-10 METRA ELECTRONICS CORPORATION TABLE OF CONTENTS Dash Disassembly 1996-1999 Infiniti I-30 ...... 1 1993-1995 Mercury Villager /1993-1995 Nissan Quest ...... 2 1996-1998 Mercury Villager/ 1996-1998 Nissan Quest ...... 3 1999-2002 Mercury Villager /1999-2003 Nissan Quest ...... 4 1995-1999 Nissan Sentra /1995-1998 200 SX...... 5 1995-1998 Nissan 240 SX ...... 6 1998-2001 Nissan Altima ...... 7 1998-2001 Nissan Frontier/2000-2001 Nissan Xterra ...... 8 2002-2004 Nissan Frontier/2002-2004 Nissan Xterra ...... 9 1995-1999 Nissan Maxima...... 10 2000-2003 Nissan Maxima...... 11 1996-2000 Nissan Pathfinder/QX4 1997-2000...... 12 2001-2004 Nissan Pathfinder...... 13 * Fits all models EXCEPT the Bose and Comfort & Convenience pkgs. Kit Assembly Double DIN Head Unit Provision...... 14 Stacked ISO DIN Head Unit Provision ...... 15 Mercury Villager 1993-98...... 16 Mercury Villager/Nissan Quest 199-02 & Nissan 200SX 1995-98...... 17 Nissan 240SX 1995-98 & Nissan Altima 1998-01 ...... 18 Nissan Frontier 1998-04...... 19 Nissan Maxima 1995-03...... 20 Nissan Pathfinder 1996-03...... 21 Nissan Quest 1993-98 ...... 22 Nissan Sentra 1995-99 / Xterra 2000-01 ...... 23 Infiniti I30 1996-99 / All Vehicles...... 24-25 Final Assembly...... 26 CAUTION: Do not cycle the key when removing a dash with passenger airbag ON/OFF switch.

KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. DASH DISASSEMBLY

1996-1999 INFINITI I-30

1 Disconnect the negative battery terminal to prevent an accidental short circuit.

2 Unclip and remove the shift lever trim panel and remove the (2) screws exposed.

3 Remove (1) screw to the left of the ashtray then unclip and remove the ashtray assembly.

4 Unclip and remove the clock/vent assembly.

5 Remove (4) screws securing the radio.

1 DASH DISASSEMBLY

1993-1995 MERCURY VILLAGER 1993-1995 NISSAN QUEST

1 Disconnect the negative battery terminal to prevent an accidental short circuit.

2 Remove (1) screw above the climate controls.

3 Unclip and remove the radio trim panel.

4 Remove (4) screws securing the radio.

2 DASH DISASSEMBLY

1996-1998 MERCURY VILLAGER 1996-1998 NISSAN QUEST

1 Disconnect the negative battery terminal to prevent an accidental short circuit.

2 Remove (4) plastic screws and screw anchors from the base of the storage compartment then remove the compartment.

3 Remove (2) Phillips screws from the base of the radio trim panel.

4 Remove (2) Phillips screws from above the radio opening.

5 Remove the ashtray.

6 Remove (4) screws securing the radio.

3 DASH DISASSEMBLY

1999-2002 MERCURY VILLAGER 1999-2003 NISSAN QUEST

1 Disconnect the negative battery terminal to prevent an accidental short circuit.

2 Open the ashtray/cupholder assembly and depress the retaining clips on each side to remove.

3 Remove (2) Phillips screws from each side of the ashtray/cupholder.

4 Remove (4) plastic rivets from the lower pocket and slide the pocket back. Note: It is not necessary to fully remove the pocket.

5 Unclip the dash trim panel and remove.

6 Remove (4) Phillips screws securing the radio.

4 DASH DISASSEMBLY

1995-1999 NISSAN SENTRA 1995-1998 200 SX

1 Disconnect the negative battery terminal to prevent an accidental short circuit.

2 Unclip and remove the dummy plate above the climate controls.

3 Remove (1) Phillips screw from behind dummy plate.

4 Unclip and remove radio trim panel.

5 Remove (4) Phillips screws securing radio.

5 DASH DISASSEMBLY

1995-1998 NISSAN 240 SX

1 Disconnect the negative battery terminal to prevent an accidental short circuit.

2 Unclip and remove the climate control trim panel and remove the (2) exposed behind.

3 Unclip and remove the shift lever trim panel and remove the (2) screws exposed behind.

4 Remove the ashtray and (1) Phillips screw exposed in the ashtray cavity.

5 Unclip and remove the radio trim panel, factory radio and pocket assembly.

6 DASH DISASSEMBLY

1998-2001 NISSAN ALTIMA

1 Disconnect the negative battery terminal to prevent an accidental short circuit. 1 2 Unclip the shift lever trim panel and remove (2) Phillips screws at the base of the radio trim panel.

3 Remove (2) Phillips screws above the radio opening.

4 Unclip and remove the radio trim panel.

5 Remove (4) Phillips screws securing the radio.

7 DASH DISASSEMBLY

1998-2001 NISSAN FRONTIER 2000-2001 NISSAN XTERRA

1 Disconnect the negative battery terminal to prevent an accidental short circuit.

2 Remove the ashtray and the (2) Phillips screws exposed in the ashtray cavity.

3 Unclip and remove the radio trim panel.

4 Remove (4) Phillips screws securing the radio.

8 DASH DISASSEMBLY

2002-2004 NISSAN FRONTIER 2002-2004 NISSAN XTERRA

1 Disconnect the negative battery terminal to prevent an accidental short circuit.

2 Unclip and remove the shift lever trim panel.

3 Remove (2) Phillips screws exposed in the shift lever cavity.

4 Remove (2) Phillips screws under the climate control.

5 Unclip and remove the radio trim panel.

6 Remove (4) Phillips screws securing the radio.

9 DASH DISASSEMBLY

1995-1999 NISSAN MAXIMA

1 Disconnect the negative battery terminal to prevent an accidental short circuit.

2 Unclip the shift lever trim panel.

3 Remove the (2) Phillips screws at the base of the radio trim panel.

4 Remove (1) Phillips screw to the left of the ashtray and unclip the ashtray assembly.

5 Unclip and remove the clock/vent assembly.

6 Remove (4) Phillips screws securing the radio.

10 DASH DISASSEMBLY

2000-2003 NISSAN MAXIMA

1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2

2 Unclip and remove the vent/radio trim panel. Note: For Bose systems the vent assembly will be removed without the trim panel. 5 3 Remove the ashtray insert and (1) 5 Phillips screw exposed behind.

4 Unclip and remove the shift lever/ash- 5 5 tray trim panel.

5 Remove (2) Phillips screws above the radio and (2) Phillips screws below the 4 climate control panel then remove the radio/climate control assembly.

11 DASH DISASSEMBLY

1996-2000 NISSAN PATHFINDER/QX4 1997-2000

1 Disconnect the negative battery terminal to prevent an accidental short circuit.

2 Remove (2) Phillips screws from the base of the radio trim panel.

3 Unclip and remove the radio trim panel.

4 Remove (4) Phillips screws securing radio.

12 DASH DISASSEMBLY

2001-2003 NISSAN PATHFINDER

1 Disconnect the negative battery terminal A to prevent an accidental short circuit.

2 Unclip and remove the vent/clock assembly. (Figure A)

3 Remove (2) Phillips screws from the top of the radio trim panel then remove the panel. (Figure B)

4 Remove (4) Phillips screws securing radio. (Figure C) B

13 KIT ASSEMBLY

DOUBLE DIN HEAD UNIT PROVISION

A 1 Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A)

2 Attach the factory mounting brackets and the 95-7417 DDIN trim plate/bracket assembly to the DDIN head unit with the screws supplied with the unit. (Figure B)

14 KIT ASSEMBLY

STACKED ISO DIN HEAD UNIT PROVISION A 1 Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A)

2 Attach the factory mounting brackets and the 95-7417 DDIN trim plate/bracket assembly to the stacked ISO DIN head units with the screws supplied with the units. (Figure B)

15 FINAL ASSEMBLY

MERCURY Villager 1993-95 4

1 2

"D"

"D" "D"

"D" Disconnect the negative battery terminal to prevent an accidental short circuit. Remove D (1) screw above the climate controls. Unclip Cut and remove all mounting tabs on the radio trim bezel and remove. Remove tabs down. Slide the aftermarket head unit into the cage until secure (see Fig. A). Bracket Set #2 EXCEPT tabs "D". (The ISO HEAD UNITS: (4) Phillips screws securing the factory radio tabs can be identified by the stamped letter housing and remove the housing. screws supplied with the unit. Slide the head unit assembly into the R by each tab). Skip to the Installation side clips engage and attach the I Disconnect the wiring. Remove (8) Phillips Instructions for ALL VEHICLES on Page #9. screws securing the factory radio to the factory radio housing and remove the radio.

MERCURY Villager 1996-98

1 2

"D"

"D" "D" R

Locate the factory wiring harness in the Disconnect the negative battery terminal to prevent an accidental short circuit. Remove "D" dash. Metra recommends using the (4) plastic screws from the base of the storage proper mating adaptor and making compartment. Pop out (4) anchor clips connections as shown. (Isolate and (securing the screws) and remove the Cut and remove all mounting tabs on individually tape off the ends of any compartment. Remove (2) Phillips screws Bracket Set #2 EXCEPT tabs "D". (The unused wires to prevent electrical short from the base of the radio trim bezel. circuit). Remove (2) Phillips screws above the radio tabs can be identified by the stamped letter opening. Remove the ashtray. Pull up and by each tab). Skip to the Installation out on the radio trim bezel and remove the Instructions for ALL VEHICLES on Page #9. bezel. Remove (4) Phillips screws securing the factory radio housing and remove the housing. Disconnect the wiring. Remove (2) Phillips screws securing the factory radio to the housing and remove the radio. 1 16 FINAL ASSEMBLY

MERCURY Villager / NISSAN Quest 1999-02

1 2

"A"

Disconnect the negative battery terminal to Cut Bracket Set #1 along the scored lines prevent an accidental short circuit. Open removing the SHADED portions of the the ashtray/cupholder assembly, depress Brackets. Cut and remove all mounting tabs the retaining clips on each side and remove EXCEPT tabs "A". (The tabs can be the assembly. Remove (2) Phillips screws identified by the stamped letter by each tab). from each side of the ashtray/cupholder assembly. Remove (4) plastic rivets from Skip to the Installation Instructions for ALL the lower pocket and slide the pocket back. VEHICLES on Page #9. (NOTE: It is NOT necessary to remove the pocket. Unclip the dash trim bezel and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring.

NISSAN 200SX 1995-98

1 2

"A"

"A" "A"

"A"

"A" "A"

Disconnect the negative battery terminal to Cut Bracket Set #3 along the scored lines prevent an accidental short circuit. Unclip removing the SHADED portions of the the dummy plate from the center of the Brackets. Cut and remove all mounting tabs switch panel (above the radio opening). EXCEPT tabs "A". (The tabs can be Unclip the radio trim bezel and remove. identified by the stamped letter by each tab). Remove (4) Phillips screws securing the Skip to the Installation Instructions for ALL factory head unit and disconnect the wiring. VEHICLES on Page #9. Remove (2) Phillips screws securing the factory cupholder and remove. 2

17 FINAL ASSEMBLY

NISSAN 240SX 1995-98 NISSAN Sentra 1995-99

12 1 2 "C" "A"

"C" "B" "A" "A"

"A"

"A" "A" "B"

Disconnect the negative battery terminal to Cut Bracket Set #3 along the scored lines Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip removing the SHADED portions of the prevent an accidental short circuit. Unclip the climate control trim bezel and remove (2) Cut and remove all mounting tabs on the the dummy plate from the center of the Brackets. Cut and remove all mounting tabs screws exposed. Unclip the gear shifter trim Radio Housing EXCEPT tabs "B" and "C". switch panel (above the radio opening). EXCEPT tabs "A". (The tabs can be bezel and remove (2) screws exposed. (The tabs can be identified by the stamped Unclip the radio trim bezel and remove. identified by the stamped letter by each tab). Remove the ashtray and (1) screw exposed. letter on each tab). Skip to the Installation Remove (4) Phillips screws securing the Skip to the Installation Instructions for ALL Unclip the radio trim bezel (the factory head Instructions for ALL VEHICLES on Page #9. factory head unit and disconnect the wiring. VEHICLES on Page #9. unit, pocket and mounting brackets are Remove (2) Phillips screws securing the secured to the bezel). Disconnect the wiring. factory cupholder and remove. Remove the screws securing the mounting brackets to the assembly and remove the brackets.

NISSAN Altima 1998-01 NISSAN Xterra 2000-01

12"B" 1 2

"B" "B" "B"

"A" "B"

"B"

"A"

Disconnect the negative battery terminal to Cut Bracket Set #3 along the scored lines Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip removing the SHADED portions of the prevent an accidental short circuit. Remove Cut Bracket Set #2 along the scored lines the gear shifter trim bezel and remove (2) Brackets. Cut and remove all mounting tabs the ashtray and (2) Phillips screws exposed removing the SHADED portions of the Phillips screws exposed. Remove (2) EXCEPT tabs "B". (The tabs can be in the ashtray cavity. Unclip the radio trim Brackets. Cut and remove all mounting tabs Phillips screws above the radio opening. identified by the stamped letter by each tab). bezel and remove. Remove (4) Phillips EXCEPT tabs "A" and "B". (The tabs can Unclip the radio trim bezel. Remove (4) Skip to the Installation Instructions for ALL screws securing the factory head unit and be identified by the stamped letter by each Phillips screws from the factory head unit VEHICLES on Page #9. disconnect the wiring. tab). Skip to the Installation Instructions for and disconnect the wiring. ALL VEHICLES on Page #9. 3 18 FINAL ASSEMBLY

N NISSAN Frontier 1998-01

1 2

"B"

"A"

"B"

"A"

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove Cut Bracket Set #2 along the scored lines the ashtray and (2) Phillips screws exposed removing the SHADED portions of the in the ashtray cavity. Unclip the radio trim Brackets. Cut and remove all mounting tabs bezel and remove. Remove (4) Phillips EXCEPT tabs "A" and "B". (The tabs can screws securing the factory head unit and be identified by the stamped letter by each disconnect the wiring. tab). Skip to the Installation Instructions for ALL VEHICLES on Page #9.

NISSAN Frontier / Xterra 2002-04

1 2

"B"

"A"

"B"

"A"

Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip Cut Bracket Set #2 along the scored lines the gear shifter trim bezel and remove. removing the SHADED portions of the Remove (2) Phillips screws exposed in the Brackets. Cut and remove all mounting tabs shifter cavity. Remove (2) Phillips screws EXCEPT tabs "A" and "B". (The tabs can under the climate control cluster. Unclip the be identified by the stamped letter by each radio trim bezel and remove. Remove (4) tab). Skip to the Installation Instructions for Phillips screws securing the factory head ALL VEHICLES on Page #9. unit and disconnect the wiring. CAUTION: DO NOT CYCLE THE KEY WHEN REMOVING A DASH WITH PASSENGER AIRBAG ON/OFF SWITCH). 4 19 FINAL ASSEMBLY

NISSAN Maxima 1995-99

1 2 Fig. A

"A"

"A" "A"

Fig. B

"A" Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip Using a hammer, flatten the protruding the gear shifter trim bezel and remove (2) screw holes on the factory mounting screws exposed. Remove (1) screw to the brackets. Mount the factory pocket to the left of the ashtray and unclip the ashtray brackets with those screws previously assembly. Unclip the clock/vent assembly removed in step #1 (Fig. A). Cut and remove and remove. Remove (4) screws from the all mounting tabs on the Radio Housing top of the mounting bracket assembly. EXCEPT tabs "A" (Fig. B). The tabs can be Disconnect the wiring and remove the indentified by the stamped letter on each tab. assembly. Remove the screws securing the Skip to the Installation Instructions for ALL mounting brackets to to the assembly and VEHICLES on Page #9. remove the brackets.

NISSAN Maxima 2000-03

1 2 1

Illustration not available

Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the vent/radio trim bezel assembly and remove. (NOTE: For Bose systems, the vent assembly will be removed without the bezel). Remove Cut and remove all mounting tabs on the the ashtray insert and (1) Phillips screw Radio Housing. Skip to the Installation exposed. Unclip the gear shifter bezel/ashtray Instructions for ALL VEHICLES on Page #9. assembly and remove. Remove (2) Phillips screws above the factory head unit and (2) Phillips screws below the climate control panel. Remove the head unit/climate control panel assembly and disconnect the wiring. 5 20 FINAL ASSEMBLY

NISSAN Pathfinder 1996-00

1 2

"C"

"A" "C"

"A" Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) screws from the base of the radio trim Cut Bracket Set #2 along the scored lines bezel. Unclip the bottom edge of the radio removing the SHADED portions of the trim bezel and disconnect the hazard light, Brackets. Cut and remove all mounting tabs defroster, wiper and cligarette lighter wiring. EXCEPT tabs "A" and "C". (The tabs can Remove the radio trim bezel. Remove (4) be identified by the stamped letter by each screws securing the factory head unit and tab). Skip to the Installation Instructions for disconnect the wiring. ALL VEHICLES on Page #9.

NISSAN Pathfinder 2001-03

1 2 "B" I Illustration not "B" available "B"

"B" Disconnect the negative battery terminal to prevent an accidental short circuit. Using a screwdriver, pry out on the top of the vent assembly (w/ clock) and remove. Remove (2) Phillips screws from the top of the radio trim Cut and remove all mounting tabs from bezel and remove. Remove (4) Phillips screws Bracket Set #1 EXCEPT tabs "B". (The securing the factory head unit and disconnect tabs can be identified by the stamped letter the wiring. by each tab). Skip to the Installation Instructions for ALL VEHICLES on Page #9. 6 21 FINAL ASSEMBLY

NISSAN Quest 1996-98

1 2

"D"

"D" "D"

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove "D" (4) plastic screws from the base of the storage compartment. Pop out (4) anchor clips (securing the screws) and remove the Cut and remove all mounting tabs on compartment. Remove (2) Phillips screws Bracket Set #2 EXCEPT tabs "D". (The from the base of the radio trim bezel. Remove (2) Phillips screws above the radio tabs can be identified by the stamped letter opening. Remove the ashtray. Pull up and by each tab). Skip to the Installation out on the radio trim bezel and remove the Instructions for ALL VEHICLES on Page #9. bezel. Remove (4) Phillips screws securing the factory radio housing and remove the housing. Disconnect the wiring. Remove (2) Phillips screws securing the factory radio to the housing and remove the radio.

NISSAN Quest 1993-95

1 2

"D"

"D" "D"

"D" Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (1) screw above the climate controls. Unclip Cut and remove all mounting tabs on the radio trim bezel and remove. Remove Bracket Set #2 EXCEPT tabs "D". (The (4) Phillips screws securing the factory radio tabs can be identified by the stamped letter housing and remove the housing. by each tab). Skip to the Installation Disconnect the wiring. Remove (8) Phillips Instructions for ALL VEHICLES on Page #9. screws securing the factory radio to the factory radio housing and remove the radio. 7 22 FINAL ASSEMBLY

NISSAN Sentra 1995-99

1 2

"A"

"A" "A"

"A"

"A" "A"

NISSAN Xterra 2000-01

1 2

"B"

"A"

"B"

"A"

INFINITI I-30 1996-99

1 2 Fig. A

"A"

"A" "A"

Fig. B "A" Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the Using a hammer, flatten the protruding screw gear shifter trim bezel and remove (2) screws holes on the factory mounting brackets. exposed. Remove (1) screw to the left of the Mount the factory pocket to the brackets with ashtray and unclip the ashtray assembly. those screws previously removed in step #1 Unclip the clock/vent assembly and remove. (Fig. A). Cut and remove all mounting tabs on Remove (4) screws from the top of the the Radio Housing EXCEPT tabs "A" (Fig. mounting bracket assembly. Disconnect the B). The tabs can be indentified by the wiring and remove the assembly. Remove stamped letter on each tab. Skip to the the screws securing the mounting brackets to Installation Instructions for ALL VEHICLES to the assembly and remove the brackets. on Page #9.

ALL VEHICLES

Fig. B

Fig. A "

240SX, I-30, MAXIMA: Skip to step #4. ALTIMA, FRONTIER, PATHFINDER, QUEST, VILLAGER, XTERRA: Cut and remove the mounting tabs from the Radio Housing and mount the converted Brackets to the Housing with (4) #8 x Ω" Phillips Flat-head Screws supplied (Fig. A). 200SX, SENTRA: Cut and remove the mounting tabs from the Radio Housing. Mount one of the converted Brackets to the Housing with (2) #8 x Ω" Phillips Flat-head Screws supplied and mount one side of the cupholder to the Bracket with (1) factory screw and (1) locating pin. Mount the other Bracket to the Housing with (2) #8 x Ω" Phillips Flat-head Screws supplied and mount the other side of the cupholder with (1) factory screw and (1) locating pin (Fig. B). 9 24 FINAL ASSEMBLY

4 Fig. A

Fig. B

PATENT PENDING

DIN HEAD UNITS: Slide the DIN cage into the kit and secure by bending the metal locking tabs down. Slide the aftermarket head unit into the cage until secure (see Fig. A). ISO HEAD UNITS: Secure the ISO Brackets to the sides of the aftermarket head unit with the screws supplied with the unit. Slide the head unit assembly into the Radio Housing until the side clips engage and attach the ISO Trimring over the mounted head unit (see Fig. B).

5 6 A

B C

Fig. A

A) Strip wire ends back Ω" B) Twist ends together C) Solder D) Tape Re-connect the battery terminal and test the unit for proper operation. MAXIMA 1995-99, I-30: Mount the head unit/kit Locate the factory wiring harness in the assembly to the trim bezel and factory bracket dash. Metra recommends using the assembly with factory screws and mount to the proper mating adaptor and making sub-dash with factory screws (Fig. A). connections as shown. (Isolate and MAXIMA 2000-02: Mount the head unit/kit individually tape off the ends of any assembly to the factory bracket assembly with (4) unused wires to prevent electrical short Phillips Flat-head Screws supplied and mount circuit). to the sub-dash with factory screws. 240SX: Mount the head unit/kit assembly to the trim bezel (using tabs "B") with factory screws and then to the sub-dash (using tabs "C") with factory screws. 200SX, ALTIMA, FRONTIER, PATHFINDER, QUEST, SENTRA, VILLAGER, XTERRA: Mount the head unit/kit assembly to the sub-dash with 1 factory screws. 10 25 FINAL ASSEMBLY

1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.

B A) Strip wire ends back 1/2" B) Twist ends together C) Solder C D) Tape

METRA / EIA WIRING CODE 12V Ignition / Acc . . . Red Right Front (+) . . . . . Gray 12V Batt / Memory . . Yellow Right Front (-)...... Gray / Black Ground ...... Black* Left Front (+) ...... White Power Antenna . . . . . Blue Left Front (-) ...... White / Black Amp Turn-On ...... Blue / White Right Rear (+)...... Violet Amp Ground ...... Black / White Right Rear (-) ...... Violet / Black Illumination...... Orange Left Rear (+)...... Green Dimmer ...... Orange / White Left Rear (-) ...... Green / Black *NOTE: When Black a wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications. 26 NOTES NOTES NOTES 710NI INSTRUCTIONS