ArubaOS Most Useful Commands v1.2 Wireless LAN Controller Access Point Operations General Commands Access Points Commands Default Settings Display output without breaks: no paging Display the list of active APs: show ap active Default username: aruba Display system information: show tech-support Display APs known by the controller: show ap database long Default enable password: aruba123 Display common system information: show switchinfo Display the list of inactive APs: show ap database inactive Default password: aruba123 Display master-local information: show switches Display APs’ radio settings: show ap bss-table Gain full access to the CLI: ++k Display current running configuration: show running-config Display settings of an AP group: show ap-group Reboot an AP: apboot ap-name Display all log messages: show log all Reset AP to Factory Defaults Display activity statistics on each port: show port status an AP to another controller: ap-move ap-name Display OS versions used: show image version Display the list of clients connected to a specific AP: 1 - Connect a console cable to the AP show ap debug client-table ap-name 2 - Power up the AP Display the licenses installed: show license Clear old APs from the controller’s database: 3 - Hit Enter when you see the autoboot countdown Display informations about L3 interfaces: show ip interface brief clear gab-db ap-name 4 - You should see the “apboot>” prompt Save current configurations: write memory Display Regulatory Domain channels available: 5 - Enter the following commands: the current session: logout show ap regulatory-domain-profile apboot> purge apboot> save Reboot the controller: reload system Assign an AP to another AP group: ap-regroup ap-name apboot> boot Display details about a specific interface: 6 - AP will reboot with factory defaults show interface gigabitethernet <0/0> 7 - Use the default credentials to login (aruba/aruba123) Upgrade ArubaOS from a USB drive: Clients Commands usb: partition 1 filename system : partition 0 Display associated clients: show user Display a specific client details : show user mac IAP to Campus AP Radio Commands Display the authentication phase: show auth-tracebuf mac 0 - AP and controller must have some regulatory domain configurations Display the 5GHz radios config: show rf dot11a-radio-profile Display a voice client status: show ucc client-info sta 1 - Connect a console cable to the AP 2 - Enter the following command to convert the IAP to a campus AP: Display the 2.4GHz radios config: show rf dot11g-radio-profile Display clients per radio: show user bssid (iap)# convert-aos-ap CAP Display active 5GHz radios: show ap active dot11a Display clients per SSID: show user essid Display active 2.4GHz radios: show ap active dot11g Deauthenticate a client: aaa user delete Display details of a RF profile: Display the list of associated client to an AP: Configure Controller IP address show rf arm-profile show ap association ap-name 1 - Connect a console cable to the AP Display ARM information for a specific AP: Display information about a specific client: 2 - Enter the following commands to configure the WLC IP address: show ap arm rf-summary ap-name show ap client status (ap)# setenv maset Display specific AP radio statistics: show ap arm state ap-name Debug Commands Packet Capture Display current debug config: show debug Display DFS events: show log all | include radar Enable a packet capture for a specific client: Display a voice call MOS: show ucc call-info cdrs packet-capture datapath all Debug anything system related to a specific AP: Send the capture to a local file on the contoller: show ap debug system-status ap-name packet-capture destination local-filesystem Enable debug for a specific client & display the client debugs: Send the capture to a remote server (Wireshark for example): logging level debugging user-debug packet-capture destination ip-address show log user-debug all Copy the capture to the local flash: Display a client roaming history packet-capture copy-to-flash datapath-pcap show ap client trail-info Sources: ArubaOS 6.5.2.x Command-Line Interface - https://goo.gl/UCyhyP by @wattiswifi & @VergesFrancois - copyright © WATTISWIFI & SemFio Networks Inc. 2017