INSTRUCTIONS for INSTALLATION of ONE SIDED DEADLOCK with 1" (25Mm) DEADBOLT

Total Page：16

File Type：pdf, Size：1020Kb

INSTRUCTIONS FOR INSTALLATION OF ONE SIDED DEADLOCK WITH 1" (25mm) DEADBOLT 1. MARK DOOR 3. INSTALL DEADBOLT LATCH Start approximately 36"(914mm) from DOOR EDGE floor. Fold and apply template on door edge and mark center of 1-3/4"(45mm) hole on door face. (NOTE：BACKSET, 2-3/8"(60mm) or 2-3/4"(70mm), ON DOOR FACE MUST MATCH BACKSET OF YOUR DOOR FACE LOCK.) Insert latch in hole, keeping Chisel 1/8"(3mm) deep or latch face parallel to face of until latch face is flush with 2. DRILL HOLES door edge. door edge. Mark outline and remove Drill 1"(25mm) hole 4"(100mm) deep latch. 1"(25mm) HOLE in center of door edge. Drill from room 4"(100mm) DEEP side or inside of door 1-3/4"(45mm) Install latch and hole 1-3/16"(31mm) deep on door face. tighten two screws (NOTE：DO NOT DRILL MORE THAN firmly. 2-3/32"(53mm) DEEP. MAKE SURE 1-3/4"(45mm) HOLE NOT TO BREAK THROUGH TO 1-3/16"(31mm) DEEP OPPOSITE SIDE OF DOOR . DRILL JUST PASS 1"(25mm) HOLE FOR DEADBOLT LATCH.) 4. INSTALL THUMB TURN ASSEMBLY 5. INSTALL STRIKE PLATE LINER Insert TORQUE BLADE through LATCH CRANK horizontally. THUMB TURN ASSEMBLY Close door until latchbolt Measure one half of door LATCH CRANK touches jamb to locate strike thickness from door stop TORQUE BLADE in jamb and center line of and vertically make drill strike. Open door and extend point center for strike. line from make to door stop. Drill 1"(25mm) hole 1" (25mm) deep in door jamb Fix 4 screws through LINER on inside of door at the position marked on for strike. TEMPLATE then fix 2 screws through THUMB TURN ASSEMBLY firmly. Chisel 1/16"(1.5mm) deep for strike. Install and tighten screws. FOR DOOR THICK 80mm TOOLS REQUIRED： 1 phillps head screwdriver 1 45mm hole saw 1 25mm drill bit 1 chisel TEMPLATE FOLD HERE ON DOOR EDGE MARK CENTER OF 2-3/8"(60mm) BACKSET 1-3/4"(45mm) HOLE ON DOOR FACE CAUTION：DO NOT DRILL MARK MARK 2-3/4"(70mm) BACKSET 1-3/4"(45mm) HOLE FOR FOR THROUGH TO OPPOSITE 1-3/4" OR 1-3/8" SIDE OF DOOR. (READ (45mm) (35mm) INSTRUCTIONS CAREFULLY) THICK THICK DOOR DOOR.

Copy Link

Recommended publications

Bi-Metal Hole Saws Designed with Time Savings and Longevity in Mind
FLEXIBLE. EASY-TO-USE. DURABLE. BI-METAL HOLE SAWS DESIGNED WITH TIME SAVINGS AND LONGEVITY IN MIND. THE UNIVERSAL PRODUCT FOR CUTTING HOLES IN WOOD AND METAL. BI-METAL HOLE SAWS When it comes to purchasing a Bi-Metal Hole Saw, look no further. The IDEAL® Bi-Metal Hole Saw utilizes M42 high-speed steel with 8% premium cobalt and a rigged solid back plate. Providing 2.3x more holes than leading manufactures with the highest strength and greater wear resistance. The extreme deep gulleted teeth design clears out uniform chips that minimize binding on the job that provides 1.2x faster drilling time than the leading manufacturers in the market. With a standard 1-7/8” cutting dept, you can save time cutting 2’x4’s with a single pass design. The IDEAL® Bi-Metal Hole Saws effectively cut through a wide range of materials, including stainless steel, sheet metal, as well as common non-fer- rous materials, such as aluminum, copper, brass, wood, engineered wood, nail embedded wood and plastics. When it comes to IDEAL vs. the competition, we have the professional in mind. The wide offering includes sizes from 7/8” to 6” that include diamond side eyes to provide ease of slug removal. The 2” to 6” Bi-Metal Hole Saws have large cat eyes on the back, that not only provide line of sight but aid in plug removal. IDEAL is the professional’s choice for Bi-Metal Hole Saws. Average NumberAverage # of Holes before failure of Holes Drilled AVERAGE DRILL TIME(STATISTICALLY LOWER LIMIT)Average Drill Time 80 2.3X 180 1.2X MORE HOLES THAN FASTER THAN THE 70 160 THE COMPETITION 140 COMPETITION 60 LIGHT BLUE 120 50 100 DARK BLUE 40 80 ORANGE 30 60 GREEN 20 DRILL TIME(SECONDS) AVERAGE # OF HOLES 40 RED 10 20 MAROON 0 0 LIGHT BLUE ORANGE GREEN RED MAROON LIGHT BLUE DARK BLUE ORANGE GREEN RED MAROON Orange Green IDEAL Dk.
[Show full text]
Fischer Chisel
CATALOG OCTOBER 2021 DRILL BITS AND BITS CATALOG DRILL BITS AND BITS CHISELS FLAT CHISEL SDS MAX High-performance flat chisel for SDS Max drill chuck. * Long life span thanks to the specially hardened steel. * Excellent working comfort because of the high oscillation endurance. * Secure transfer of force due to the SDS Max seat. * Fischer chisel ... CODE 504284 504286 504287 PRICE € 13,61 € 15,43 € 19,96 FLAT CHISEL SDS PLUS High-performance flat chisel for SDS Plus drill chuck. * Excellent working comfort because of the high oscillation endurance. * Long life span thanks to the specially hardened steel. * Secure transfer of force due to the SDS Plus seat. * Fischer chis ... CODE 504278 PRICE € 13,83 HOLLOW CHISEL SDS PLUS High-performance gouge for SDS Plus drill chuck. * Excellent working comfort because of the high oscillation endurance. * Long life span thanks to the specially hardened steel. * Secure transfer of force due to the SDS Plus seat. * Fischer chisel SDS ... CODE 504280 PRICE € 28,43 POINTED CHISEL SDS MAX High-performance pointed chisel for SDS Max drill chuck. * Excellent working comfort because of the high oscillation endurance. * Long life span thanks to the specially hardened steel. * Secure transfer of force due to the SDS Max seat. * Fischer chi ... CODE 504281 504282 504283 PRICE € 13,61 € 15,43 € 19,96 CATALOG DRILL BITS AND BITS CHISELS POINTED CHISEL SDS PLUS High-performance pointed chisel for SDS Plus drill chuck. * Excellent working comfort because of the high oscillation endurance. * Long life span thanks to the specially hardened steel. * Secure transfer of force due to the SDS Plus seat.
[Show full text]
Product Catalogue
PRODUCT CATALOGUE www.tradeablade.com JUNE.2017 TABLE OF CONTENTS CUTTING SAW BLADES | TRADE 3 SAW BLADES | PROFESSIONAL 4 SAW BLADES | INDUSTRIAL 8 RECIPROCATING SAW BLADES | PROFESSIONAL 9 JIG SAW BLADES | PROFESSIONAL 12 ROUTER BITS | PROFESSIONAL 13 DIAMOND CUT OFF WHEELS | PROFESSIONAL 16 DIAMOND BLADES | PROFESSIONAL 17 DRILLING DIAMOND HOLE SAWS | TRADE 18 DIAMOND HD HOLE SAWS | INDUSTRIAL 18 M42 Bi-METAL HOLE SAWS | INDUSTRIAL 19 HOLE SAW MANDRELS | INDUSTRIAL 20 M42 THIN WALL HOLE SAWS | INDUSTRIAL 21 OSCILLATING UNI-FIT OSCILLATING ACCESSORIES | PROFESSIONAL 22 STARLOCK OSCILLATING ACCESSORIES | INDUSTRIAL 23 2 www.tradeablade.com CUTTING SAW BLADES TRADE TRADE-A-BLADE’s line of entry level saw blades feature an Ultra-Thin Kerf design requiring less horsepower and reduced stock loss. These fast and durable light duty blades are perfect for general purpose framing and fine finish woodworking. THIN KERF | FRAMING • General purpose framing blade provides clean and quick rip and cross-cuts in dimensional lumber • C3 grade micro-grain carbide keeps the cutting edge sharper for longer periods of time • Hardened tool steel alloy body to ensure straight, accurate cuts • ATB tooth grind with 15 degree hook angle ITEM DIAMETER TEETH ARBOR UPC TCSBT005 5-3/8” 30 5/8” | 10 mm 628204662055 Bushing TCSBT011 7-1/4” 24 5/8” | DKO 628204662116 TCSBT023 10” 28 5/8” 628204662239 THIN KERF | FINISHING • Fine finish woodworking blade provides clean, quick and accurate cross-cuts • C3 grade micro-grain carbide keeps the cutting edge sharper for longer periods of time • Hardened steel alloy body to ensure straight, accurate cuts • ATB tooth grind with 10 – 15 degree hook angle ITEM DIAMETER TEETH ARBOR UPC TCSBT008 6-1/2” 40 5/8” | DKO 628204662086 TCSBT014 7-1/4” 60 5/8” | DKO 628204662147 TCSBT026 10” 60 5/8” 628204662260 TCSBT029 12” 80 1” 628204662291 3 www.tradeablade.com CUTTING SAW BLADES PROFESSIONAL TRADE-A-BLADE’s line of professional full kerf saw blades are designed to meet the rigorous needs of professional users.
[Show full text]
Milwaukee Tools
Updated: May 2010 Pricing Effective: May 2010 MILWAUKEE TOOLS www.milwaukeetool.com INDEX ACCESSORIES COMBINATION KITS.......................................................................... 14-3 BaND SaW BLaDes.................................................................... 14-7 COPPER TUBING CUTTER............................................................... 14-5 BaTTerY PacKs/CHarGer..................................................... 14-7 CUT-OFF MACHINES........................................................................ 14-3 BiT EXTeNsioN............................................................................. 14-9 CircULar SaW BLaDes........................................................ 14-10 DRILLS.................................................................................................... 14-3 HoLe SaWs HAMMER AND HAMMER DRILLS................................................ 14-3 4/6 Bi-MeTaL ........................................................................... 14-8 HEAVY DUTY ACCESSORIES....................................................... 14-11 Arbors...................................................................................... 14-9 INTroDUcTioN................................................................................. 14-2 ice HarDeNeD bi-meTaL .................................................. 14-9 PiLoT DriLLs............................................................................ 14-9 MisceLLaNeoUs...........................................................................
[Show full text]
Mechanical Hot Tapping Machine Hole Master® Hole Cutting Base
Mechanical Hot Tapping Machine Hot tap using the DM3MECH. With the right hole saw, cut or drill into copper, steel, or plastic pipe for up to 4” valves. DM3MECH contains the base machine, along DM3MECH with 7/16” Hex Arbor, 1/4” Drill Bit, Hole Saws 5/8”, 7/8”, 1 1/8”, 1 3/8”, 1 3/4”, 2 1/4”, 3 1/4”, Allen wrenches and toolbox. DM3MECHB is the base machine in a toolbox only, without hole saws or arbor. These tools require a 1/2” drill motor, valves and fittings that are all sold separately. Catalog Item Valve Weight No. Code Size lbs kg DM3MECH 08350 3/4” - 4” 12.0 5.5 DM3MECHB 08351 3/4” - 4” 10.0 4.5 NOTE: User adds fittings and valves according to the application. Pressure Rating for ambient (room) temperature liquid systems: 300 psi. A great deal on a versatile Pressure Rating for steam systems: 125 psi. NOT recommended for ammonia or other caustic systems. The seals do not support it. tapping machine that is priced Pipe fittings well for the market. and valves sold separately. ACCESSORIES 7 DB25 43507 1/4” Drill Bit HSA716 43508 7/16” Hex Arbor CRPD25 99129 1/4” Diameter Carbide-tipped Coupon Retaining Drill Bit NEW HOLE SAWS AT BOTTOM OF PAGE. Hole Master® Hole Cutting Base The Hole Master® provides a means of clamping onto pipe and using a drill to cut a HCB-200 HCB-475 hole in the pipe. Hole Master comes with a base, chain and screw for clamping, along with a plate and drill holder for mounting a drill and hole saw to the unit.
[Show full text]
BAND SAW Bi-Metal
POWER TOOL HAND TOOLS ACCESSORIES HAND TOOLS ™ RECIPROCATING BLADES T2 Hacksaw Blades .................................... 90 LENOX Gold ® ..........................................51, 52 Hacksaw Frames .....................................91, 92 LAZER ® ......................................................... 53 Hand Saws ................................................... 93 Demolition .................................................... 54 Snips & HVAC Tools ..................................... 95 BAND SAW Bi-metal ..................................................55, 56 Plastic Tubing Cutters ............................ 96, 97 LENOX DIAMOND™ and Carbide Grit ...........57 Tubing Cutters ........................................98, 99 CARBIDE Carbide Tipped, Pallet Dismantling ............ 58 Pipe Wrenches ........................................... 100 Selecting Carbide Blades ............................. 16 Reciprocating Saw Blade Kits ..................... 59 All-In-One Screwdrivers & Hollow Shaft Nut Drivers............................101 Tooth Selection ..............................................17 Cross Reference Chart ............................60, 61 ® Locking Tradesman Utility ARMOR CT BLACK ..................................... 18 Blade, TPI & Blade Length ® ™ Knife & Utility Knives ..................................102 LENOX TNT CT & TRI-TECH ....................... 19 Selection Guides .......................................... 62 ® Utility Blades, Safety Knife & Blades ....... 103 TRI-MASTER ...............................................
[Show full text]
ICS Sawing Tools Catalog
REVISED OCT 2020 ICS CUTTING TOOLS, INC 511 Main Street • Casco, WI 54205-0125 USA (920) 837-2526 • Fax (920) 837-2530 www.icscuttingtools.com • [email protected] TABLE OF CONTENTS Adapters/Arbors Saw Blades “D” Drive Arbor ...............................................................31 Air Saw - 1/2" Shank ........................................................2 Hole Saw Arbor ...............................................................26 Band Saw - Portable .......................................................11 Hole Saw Plug Ejecting Arbor Adapter ............................26 Circular Saw Mandrel Arbor Adapter....................................................27 Carbide Tipped Cut-Off Blades Aluminum Cutting .......................................................17 Masonry Cutting .............................................................15 Biscuit Joiner ..............................................................18 Metal Cutting ..................................................................15 Combination ...............................................................16 Extensions Fiber Cement ..............................................................19 Hole Saw ........................................................................27 Laminate Cutting ........................................................16 Handsaws Melamine Cutting .......................................................17 Metal Cutting ..................................................................10 Miter Cutting ...............................................................16
[Show full text]
Drill Press Speed Chart
Twist drill bit DRILL PRESS SPEED CHART Black & Decker Recommended operating speeds (RPM) Bullet pilot-point bit Softwood Hardwood Accessory (Pine) (Hard Maple) Acrylic Brass Aluminum Steel Shop Notes Twist drill bits* 1/16" - 3/16" 3000 3000 2500 3000 3000 3000 Lubricate drill with oil when cutting steel 1/4" - 3/8" 3000 1500 2000 1200 2500 1000 1/8" or thicker. Brad-point bit 7/16" - 5/8" 1500 750 1500 750 1500 600 Use center punch on all holes to prevent 11/16" - 1" 750 500 NR 400 1000 350 drill from wandering. Black & Decker Bullet pilot-point bits* 1/8" - 3/16" 3000 3000 3000 2000 1500 3000 Good all-around bit. 1/4" - 3/8" 3000 3000 2400 1500 1000 2000 These cut more quickly than brad points 1/2" 3000 1500 1600 1500 750 1200 and twist drills. Forstner bit Brad-point bits* 1/8" 1800 1200 1500 NR NR NR Glass-and- 1/4" 1800 1000 1500 NR NR NR tile bit 3/8" 1800 750 1500 NR NR NR 1 1/2" 1800 750 1000 NR NR NR Raise /4" and smaller bits often to clear 5/8" 1800 500 750 NR NR NR shavings and prevent heat build-up. 3/4" 1400 250 750 NR NR NR 3/8" 1200 250 500 NR NR NR 1" 1000 250 250 NR NR NR Forstner bits 1/4" - 3/8" 2400 700 NR NR NR NR Raise 1/4-3/8" bits often to clear shavings 1/2" - 5/8" 2400 500 250 NR NR NR and prevent heat build-up.
[Show full text]
Installation Tools
INSTALLATION TOOLS a quality brand of QEP Co., Inc. was founded in 1979 in the New York family garage of Lewis and Susan Gould. The very first QEP branded tiling product was a “Do-It-Yourself” Bathtub Edging Kit. There was nothing like it on the market. As the popularity of tile floors began to rise in the United States, so did the demand for DIY installation tools and accessories. This demand quickly opened the doors of opportunity for the QEP brand throughout the national tile tool market. The QEP brand continued to grow and evolve, eventually expanding into the professional market. In 1984, QEP released the world’s first “dual rail” tile cutter, and in 1989 began manufacturing their own professional tile spacers. In the late 90’s, QEP Co., Inc. continued to expand its reach and began selling the QEP brand into Canada, Mexico and South America. Over the next decade, the QEP brand made its way into Australia, New Zealand, England, France and China. Today, QEP has become an recognized professional brand, specializing in installation tools and accessories for tile, porcelain and natural stone. QEP products can be found in all 50 States and in countries throughout the world. QEP continually introduces new and innovative products that address the challenges of today’s market. To establish a stronger presence in the professional tiling industry, QEP has just unveiled their most innovative line of tools yet - The Xtreme Series. Advanced designs have enhanced the professional-grade features of this new tool line that has been Engineered by the Pro, For the Pro.
[Show full text]
Glass Tile Cutting Diamond Blade
FULL Since 1979 , Q.E.P. Co., Inc has been a driving force in the continued growth and PRODUCT modernization of LINE flooring installation techniques and tools. SOLUTIONS As a world leader in the design and manufacture of quality flooring tools and accessories, our commitment to innovation and customer service has positioned QEP as the benchmark to how all other flooring tools are measured. QEP continues to introduce innovative new products that address the challenges of today’s market. Our products, from the do-it-yourself line to professional installer grade, can be found in all 50 states and in over 75 countries worldwide. We have strategically located facilities across North America, as well as across the globe, to better serve our customers’ needs. These global facilities help us stay “local” to our 3,000+ distributors in order to keep shipping lead times as short as possible. At QEP, our first priority is service to you, our valued customer. BRAND BRAND TOOLS BRAND TOOLS TOOLS - The name in - The perfect tile professional - Affordable tiling tool brand for tiling tools. tools for projects small retailers. of all sizes. TABLE OF CONTENTS Tile & Stone Installation Products Tile Saws & Diamond Blades Bridge Saws, Tile Saws, Table Top Saws, Diamond Blades, Profile Wheels, Water Pumps 2-12 Power Tools & Accessories Jamb Saws, Handheld Tile Saw, Mixers, Paddles, Drill Bits, Hole Saws 13-16 7 Tile Cutting Tools Tile Cutters, Replacement Wheels, Nippers, Pliers, Marking Tools, Hand Saws, Files 17-22 Tile Installation Tools Scrapers, Trowels, Spacers, Gloves, Knee Pads, Sponges, Floats, Kits, Grout Removers 23-34 Brand Tools 42-48 Building & Flooring Installation Tools 35-38 Tape, Laminate Tools, Brick Installation, Cement Board Installation Underlayment & Surface Protection 39-41 Ceiling Installation Tools 49-51 ® • DROP CEILING INSTALLATION • World Class..
[Show full text]
Holemaking Products & Accessories
Holemaking Products & Accessories Holemaking Products & Holemaking Products & Accessories Made of top-of-the-line materials for longer lasting performance, Klein's diverse line of drill bits and holemaking products and accessories provide accuracy and consistency to get the job done right. 232 Flexible Drill Bits Flex Bit Augers Holemaking Products Holemaking Products 53719 • Used to drill holes through wood within a wall. • Tapered back for easy bit retrieval. & Accessories • Spring steel shaft resists deformation. 53720 • Screw point tip pulls the bit through wood. • Hole in tip allows for use with wire or cable pulling grip. Cat. No. Length Weight (lbs.) 53719 53716 3/8" x 54" (9.5 mm x 1372 mm) 1.00 53717 3/8" x 72" (9.5 mm x 1829 mm) 1.00 53718 9/16" x 54" (14 mm x 1372 mm) 1.00 53718 53719 3/4" x 54" (19 mm x 1372 mm) 2.00 53751 3/4" x 72" (19 mm x 1829 mm) 2.00 53720 1" x 54" (25 mm x 1829 mm) 2.00 53716 Flex Bit Extensions 53722 • Connects to the end of a flex bit and extends the length. Cat. No. For Use with Flex Bits Length Connection Diameter Weight (lbs.) 53722 3/4" and larger 54" (1372 mm) 5/8" (14 mm) 1.00 53723 9/16" and smaller 54" (1372 mm) 7/16" (11 mm) 1.00 Flex Bit Placement Tool • For use with flexible drill bits. • Positions flexible drill bits horizontally or vertically within a wall. • Cushion Grip handle for non-slip comfort. • Folding design stores more compactly than standard tool.
[Show full text]
Cutting Tools
238 Cutting Tools Diamond Blades Premium Diamond Blade for Masonry Saw/Dry Cutting Diameters available: 14", 16", 18", 20" G-Series General Purpose Diamond Blade for Dry/ Wet Cutting Item # Code Diameter Blade Recommendation Stock* LDM3-14X1 NED 14" Hard brick and tile Y LDM-5 NED — Medium hard to soft materials A LDM-7 NED — Soft abrasive block A Super premium blade for extra long life NED — A LDM-2P and free-cutting hard materials LDM-7P NED — Super premium blade for abrasive block A Item # Code Diameter Blade Recommendation Stock* Hard material, NED — A Premium Small Diameter Diamond G-3 such as hard brick and pavers Blade for Dry Cutting G5-4X080X78 NED 4" General cutting Y Diameters available: 4", G5-7X58 NED 7" General cutting Y 4.5", 5", 6", 7", 8", 9", 10" G5-12X110X1/20 NED 12" General cutting A G5-14X110X1/20 NED 14" General cutting A G-7 NED — Abrasive material A Arbor Size Blades are available in 1", 7⁄8", 5⁄8" universal arbor and 20 mm arbor hole sizes; please specify arbor size when ordering. Nonstandard arbor holes Continuous Rim Tile are available upon request. Diamond Blade for Item # Code Diameter Blade Recommendation Stock* Wet Cutting LDX-3 NED — Hard material, such as hard brick A Diameters available: 4", 4.5", 5", 6", 7", 8", 10", 12", 14" General cutting of concrete, masonry NED 6" Y LDX5-6X58 materials and soft brick Ned-kut’s premium quality continuous rim tile blades are designed for wet General cutting of concrete, masonry LDX5-8X58 NED 8" A cutting on a variety of ceramic, quarry, materials and soft brick tile, marble and slate.
[Show full text]