User’s Guide This household machine is designed to comply with IEC/EN 60335-2-28 and UL1594. IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this household . Keep the instructions at a suitable place close to the machine. Make sure to hand them over if the machine is given to a third party. DANGER –TO REDUCE THE RISK OF ELECTRIC SHOCK: • A sewing machine should never be left unattended when plugged in. The electrical socket, to which the machine is plugged in should be easily accessible. Always unplug this sewing machine from the electric outlet immediately after using and before cleaning, removing covers, lubricating or when making any other user servicing adjustments mentioned in the instruction manual. WARNING –TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO PERSON: • Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children. • Use this sewing machine only for its intended use as described in this manual. Use only attachments recommended by the manufacturer as contained in this manual. • Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment. • Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the sewing machine and foot control free from the accumulation of lint, dust, and loose cloth. • Keep fingers away from all moving parts. Special care is required around the . • Always use the proper needle plate. The wrong plate can cause the needle to break. • Do not use bent needles. • Do not pull or push fabric while stitching. It may deflect the needle causing it to break. • Wear safety glasses. • Switch the sewing machine off (“0”) when making any adjustment in the needle area, such as threading needle, changing needle, threading , or changing , etc. • Never drop or insert any object into any opening. • Do not use outdoors. • Do not operate where aerosol (spray) products are being used or where oxygen is being administrated. • To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet. • Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. • The foot control is used to operate the machine. Avoid placing other objects on the foot control. • Do not use the machine if it is wet. • If the LED lamp is damaged or broken, it must be replaced by the manufacturer or its service agent or a similarly qualified person, in order to avoid a hazard. • If the cord connected with the foot control is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person, in order to avoid a hazard. • This sewing machine is provided with double insulation. Use only identical replacement parts. See instructions for Servicing of Double-Insulated Appliances. SAVE THESE INSTRUCTIONS

FOR CENELEC COUNTRIES ONLY: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. The noise level under normal operating conditions is less than 80dB(A). The machine must only be used with foot control of type FR5 manufactured by Shanghai Binao Precision Mould Co., Ltd.

FOR NON CENELEC COUNTRIES: This sewing machine is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the sewing machine by a person responsible for their safety. Children should be supervised to ensure that they do not play with the sewing machine. The noise level under normal operating conditions is less than 80dB(A). The machine must only be used with foot control of type FR5 manufactured by Shanghai Binao Precision Mould Co., Ltd. SERVICING OF DOUBLE INSULATED PRODUCTS In a double-insulated product, two systems of insulation are provided instead of grounding. No ground means is provided on a double-insulated product, nor should a means for grounding be added to the product. Servicing of a double-insulated product requires extreme care and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a double-insulated product must be identical to those parts in the product. A double-insulated product is marked with the words ‘DOUBLE INSULATION’ or ‘DOUBLE INSULATED’. Federal Communication Commission Interference Statement For the USA and Canada Responsible party: VSM Group AB (wholly owned subsidiary of SVP Worldwide) Drottninggatan 2, 56184 Huskvarna, SWEDEN

Product name: PFAFF® creative icon™ sewing and machine Model number: SFP1

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the authorized PFAFF® retailer or an experienced radio/TV technician for help. The included interface cable should be used in order to ensure compliance with the limits for a Class B digital device. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Declaration of Conformity For Europe Hereby, VSM Group AB (wholly owned subsidiary of SVP Worldwide), declares that this sewing and embroidery machine is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. TABLE OF CONTENTS 1 Built-in User’s Guide...... 10 Spool Caps ...... 31 Welcome to the Built-in User’s Guide! ...... 10 Threads ...... 32 Finding a Topic ...... 10 Needles ...... 33 Navigating the User’s Guide ...... 10 Important Needle Information...... 33 2 Introduction ...... 11 Changing the Needle ...... 34 Threading...... 35 Machine Overview...... 11 Threading the Upper ...... 35 Front...... 11 Automatic ...... 37 Needle Area ...... 12 Threading Tips and Hints ...... 39 Right Side ...... 12 Threading for Twin Needle ...... 40 Rear...... 12 Top...... 13 Bobbin Winding...... 42 Accessory Tray...... 13 Winding Through the Needle...... 43 Storing a Needle Plate...... 14 Inserting the Bobbin...... 44 Embroidery Unit ...... 14 Changing the Bobbin Case...... 45 Function ...... 15 IDT™ System (Integrated Dual Feed) ...... 46 Presser Foot Up and Extra Lift...... 15 Engaging the IDT™ System...... 46 Presser Foot Down and Pivot ...... 15 Disengaging the IDT™ System ...... 46 Automatic Needle Threader ...... 15 Changing the Presser Foot...... 47 Function ...... 15 Remove Presser Foot...... 47 Immediate Tie-Off ...... 16 Attach Presser Foot...... 47 Re-Start...... 16 Attaching the Sensormatic Needle Stop Up/Down ...... 16 Start/Stop ...... 16 Foot ...... 47 Reverse ...... 16 Attaching the Dynamic Spring Foot 6D ...... 48 Basic Gestures for the Multi-Touch Changing to Needle Plate .....49 Screen ...... 17 4 Embroidery Preparations...... 50 Accessories...... 18 Included Accessories ...... 18 Embroidery Unit ...... 50 Included Hoops...... 18 Embroidery Hoop Overview...... 50 Presser Feet ...... 19 Dynamic Spring Foot 6D ...... 50 Stitch Overview ...... 21 Straight Stitch Needle Plate ...... 51 Utility Stitches...... 21 Designs...... 51 Stitch Menu Overview ...... 25 creative icon™ Sampler Book...... 51 Alphabets ...... 25 Connect the Embroidery Unit...... 52 3 Preparations ...... 26 Remove the Embroidery Unit...... 52 Unpacking Machine and Embroidery To Hoop the Fabric ...... 53 Unit ...... 26 Slide on/off the Hoop...... 53 Connect the Power Cord and Foot 5 The Multi-Touch Screen...... 54 Control ...... 26 Multi-Touch Screen...... 54 Pack Away After Sewing ...... 27 Gestures...... 54 USB Ports ...... 27 Start Page ...... 55 Using a USB device...... 27 Start Sewing ...... 55 Getting Started with WiFi and Start Embroidering ...... 55 mySewnet™ Cloud...... 28 Load From mySewnet™ ...... 55 LED Lights ...... 28 Open Help Center...... 55 Free Arm ...... 28 Main Functions ...... 56 Manual Thread Cutter ...... 28 Save...... 56 Home ...... 56 Knee-Lift ...... 29 Mode Switch ...... 56 Speed Control Lever ...... 29 Common Functions...... 56 Thread Sensor ...... 29 OK...... 56 Telescopic Thread Guide ...... 30 Cancel...... 56 Spool ...... 31 Touch & Hold ...... 56 Settings with Toggle Function ...... 57 Settings in Sewing Mode ...... 85 Help Center...... 58 ActivStitch™ Technology ...... 85 User’s Guide ...... 58 Automatic Presser Foot Lift ...... 86 Getting Started ...... 58 Automatic Thread Cutter ...... 86 Techniques and Tutorials ...... 58 Free-Motion Options...... 86 Stabilizer Guide...... 58 Stitch Limiting Options ...... 87 Settings...... 59 Needle Stop Position...... 88 Presser Foot Pressure ...... 88 Sewing Settings ...... 59 Options for ...... 88 Embroidery Settings ...... 62 Tie-Off Options ...... 88 Machine Settings ...... 64 WiFi Settings...... 65 Stitch Edit...... 89 mySewnet™ Settings...... 65 Stitch Width ...... 89 Machine Information ...... 65 Stitch Positioning...... 89 Smart Toolbox...... 66 Stitch Length ...... 89 Stitch Density ...... 90 Top Bar...... 66 Mirroring...... 90 Help Center...... 66 Buttonhole Slit Length ...... 90 Quick Help ...... 66 Stitch Repetition ...... 90 Main Menu ...... 67 ActivStitch™ Technology ...... 91 Information Area ...... 67 Free-Motion Options...... 92 WiFi ...... 68 Dynamic Spring Foot 6D Free-Motion...... 92 mySewnet™ ...... 68 Spring Foot Free-Motion ...... 92 Recommendations ...... 68 Sensormatic Free-Motion...... 92 Information...... 69 Active Features...... 69 Tie-Off Options ...... 93 Menu Panel ...... 69 Stitch Repeat ...... 93 Options Selected From the Menu Panel ...... 70 Save Stitch ...... 94 Toolbar ...... 71 Balance ...... 94 Customize Your Work Area ...... 71 Sewing Programs ...... 95 Full Screen View ...... 71 Tapering Stitches ...... 95 Base Bar...... 71 Taper Satin Stitch Exercise...... 95 Stitch Repeat ...... 96 6 WiFi & mySewnet™ Services ...... 73 Patchwork Program...... 96 Single Stitch Program...... 96 WiFi Introduction ...... 73 Combining Programs...... 96 Getting Started With WiFi ...... 73 Sewing Techniques ...... 97 Hidden Network ...... 73 ...... 97 Firmware Update Using WiFi ...... 73 Sew On a Button...... 98 Firmware Update Using a USB Device...... 73 Four Direction Sewing ...... 98 Complimentary Software ...... 73 Special Stitch Techniques...... 99 mySewnet™ Services ...... 75 Ribbon Stitches...... 99 mySewnet™ Account ...... 75 Stacking Stitches...... 99 mySewnet™ Cloud ...... 75 Floating Stitches ...... 100 Used Space in mySewnet™ Cloud...... 76 Radiant Stitches...... 101 Installation of mySewnet™ cloud Sync Lace Edge Stitches ...... 101 Tool for Computer...... 76 Optional Feet Stitches ...... 101 mySewnet™ Portal...... 77 Pop-up Messages in Sewing ...... 102 SewNotice App ...... 78 Troubleshooting Connectivity ...... 78 8 Embroidery Edit...... 104 Embroidery Edit — Introduction...... 104 7 Sewing...... 79 Embroidery Edit – Overview...... 105 Sewing Mode – Introduction ...... 79 Getting Started with Embroidering...... 107 Sewing Mode – Overview ...... 79 Load a Design ...... 107 Getting Started with Sewing...... 82 Load a Font ...... 107 Load a Stitch From the Menu Panel...... 82 Load a Stitch ...... 108 Select a Stitch From the Selection Menu...... 83 Load From Another Location ...... 108 Load a Stitch from File Manager ...... 83 Color Edit...... 109 Sewing Recommendations...... 84 Change More Than One Color Block ...... 109 Layers...... 110 Select Design(s)/Change Stitch-Out -Out – Introduction ...... 131 Order...... 110 Embroidery Stitch-Out – Overview...... 132 Select One Design ...... 110 Embroidery Stitch-Out Settings...... 133 Select All...... 110 Attach Selected Hoop...... 133 Multi-Select...... 111 Attached Needle Plate...... 133 Group/Ungroup ...... 111 Selected Foot Type...... 133 Edit Functions ...... 112 ActivStitch™ Technology ...... 135 Control Wheel ...... 112 Thread Cut Options ...... 135 Move ...... 113 Basting Options ...... 135 Rotate ...... 114 Color Options...... 135 Scale ...... 114 Turnable Hoop Options – Side Sort...... 135 Zoom Options ...... 116 Color Block List...... 136 Duplicate/Multi Duplicate...... 116 Basting Options...... 136 Delete/Delete All ...... 116 Mirroring...... 116 Ghost Mode...... 137 Move into Hoop ...... 116 Color Block Sort ...... 137 Undo/Redo ...... 117 Color Block Merge ...... 137 Pan ...... 117 Monochrome...... 137 Resize ...... 117 Stitch-Out Progress ...... 139 Hoop Options ...... 119 Number of Stitches in Current Color Hoop Selection ...... 119 Grid...... 119 Block...... 139 Background...... 119 Number of Stitches in Embroidery Stitch Edit...... 120 Combination ...... 139 Full Screen View ...... 120 Progress Circle ...... 139 Embroidery Text ...... 121 Remaining Embroidery Time by Color Create a Text ...... 121 Block...... 139 Add a Letter...... 121 Hoop Position ...... 140 Delete a Letter ...... 121 Current Stitch Position...... 140 Text Shaping ...... 122 Park Position...... 140 Smart Toolbox on a Design...... 123 Position ...... 140 Duplicate ...... 123 Center Position...... 140 Multi Duplicate ...... 123 Step Stitch-by-Stitch...... 141 Mirroring...... 123 Go to Stitch ...... 141 Move into Hoop ...... 123 ActivStitch™ Technology ...... 141 Grid On/Off ...... 123 Delete/Delete All ...... 123 Zoom Options ...... 141 Read about Embroidery Edit ...... 123 Precise Positioning...... 142 Reset Toolbar ...... 123 Getting Started with Precise Positioning...... 142 Smart Toolbox on Embroidery Area...... 124 Precise Positioning Exercise...... 143 Move Into Hoop ...... 124 Zoom to Cursor ...... 144 Grid On/Off ...... 124 Set Cursor Point ...... 144 Delete All...... 124 Save Current State/Restore Current Read about Embroidery Edit ...... 124 State...... 145 Reset Toolbar ...... 124 Auto Save ...... 145 Settings in Embroidery Edit...... 125 Pop-up Messages in Embroidery Stitch- ActivStitch™ Technology ...... 125 Out ...... 146 Embroidery Foot Type ...... 126 Twin Needle Options...... 126 10 Shape Creator ...... 150 Thread Cut Options ...... 127 Shape Creator – Introduction ...... 150 Presser Foot Height ...... 128 Shape Creator – Overview...... 151 Select Default Hoop Size ...... 128 Getting Started with Shape Creator...... 153 Save Design...... 128 Load a Shape...... 153 Save Current State/Restore Current Load a Letter Shape ...... 153 State...... 129 Load a Design ...... 153 Pop-up Messages in Embroidery Edit ...... 130 Load a Stitch...... 154 9 Embroidery Stitch-Out...... 131 Edit Shape ...... 154 Rotate ...... 154 Definition of a Stitch Point...... 186 Scale ...... 156 Select Stitches/Stitch Points...... 186 Combination Repeat/Duplicate Last...... 156 Preview ...... 187 Set Number of Designs/Stitches ...... 157 Stitch Creator™ Edit Tools ...... 187 Zoom Options ...... 157 Zoom...... 187 Positioning...... 158 Move ...... 187 Control Points ...... 158 Add a Stitch or Stitch Point ...... 188 Edit Existing Shape ...... 160 Duplicate Selected Stitch Point ...... 188 Shape Creator Exercise ...... 160 Triple Stitch...... 188 Mirroring...... 188 11 Appliqué Creator ...... 161 Delete Selected Stitch Point ...... 188 Appliqué Creator – Introduction...... 161 Edit a stitch made in Stitch Creator™...... 189 Appliqué Creator – Overview...... 162 Load and Sew a Stitch...... 189 Getting Started with Appliqué Creator ...... 164 Sewing Mode ...... 189 Load a Shape...... 164 Embroidery Edit...... 189 Load a Letter Shape ...... 164 Saving a Stitch...... 189 Embroidery Edit...... 189 Load Autofill Stitch...... 164 Using Created Stitches in Sewing and Load a Design ...... 165 Embroidery Mode...... 189 Load a Stitch...... 165 Using Created Stitches in Sequence Edit Appliqué...... 166 Creator ...... 189 Rotate ...... 166 Pop-up Messages in Stitch Creator™ Scale ...... 167 Combination Repeat/Duplicate Last...... 168 Feature ...... 190 Set Number of Designs/Stitches ...... 168 Zoom Options ...... 168 14 Help Center ...... 191 Positioning...... 169 Help Center – Introduction...... 191 Control Points ...... 169 Help Center – Overview ...... 191 Edit Existing Appliqué ...... 172 User’s Guide ...... 192 Create Appliqué Exercise ...... 172 Getting Started...... 193 Appliqué Stitch-Out...... 173 Techniques and Tutorials ...... 194 Garment Techniques...... 194 12 Sequence Creator ...... 174 Sewing Techniques ...... 194 Sequence Creator — Introduction ...... 174 Quilting Techniques ...... 195 Sequence Creator – Overview...... 175 Embroidery Techniques ...... 195 Getting Started with Sequence Creator ...... 177 Stabilizer Guide ...... 195 Load a Stitch ...... 177 Projects ...... 196 Load a Font ...... 177 Project Viewer ...... 196 Adjust text and stitches ...... 178 Video Player...... 197 Delete a Stitch or Letter ...... 178 Duplicate a Stitch or Letter ...... 178 15 File Manager ...... 198 Replace a Stitch or Letter...... 178 File Manager – Introduction ...... 198 Directional Stitches ...... 179 File Manager – Overview...... 198 Sequence Commands...... 180 File Formats...... 199 True Size...... 180 Browse File Manager ...... 199 Saving a Sequence...... 180 Open a File or Folder ...... 199 Sew or Embroider Your Sequence ...... 181 Multi-Select ...... 199 Adjust the Entire Sequence...... 182 mySewnet™ Cloud Folder ...... 199 Using Sequence Creator in Sewing Mode USB Device...... 200 and Embroidery Edit ...... 182 List/Thumbnail View ...... 200 Pop-up Messages in Sequence Creator...... 183 Move up One Folder Level ...... 200 Organize...... 200 13 Stitch Creator™ Feature ...... 184 Create New Folder...... 200 Stitch Creator™ Feature – Introduction..... 184 Rename a File or Folder ...... 200 Stitch Creator™ Feature – Overview ...... 185 Move a File or Folder ...... 201 Getting Started with Stitch Creator™...... 186 Copy a File or Folder ...... 202 Delete a File or Folder ...... 202 Pop-up Messages in File Manager...... 202 16 Maintenance ...... 204 Cleaning the Machine Exterior ...... 204 Removing the Needle Plate and Cleaning the Bobbin Area ...... 204 Cleaning Under the Bobbin Area ...... 204 Replacing the Needle Plate...... 205 Troubleshooting...... 205 Service ...... 208 Non-Original Parts and Accessories...... 209 Technical specification...... 209 17 IMPORTANT ...... 210 IMPORTANT SAFETY INSTRUCTIONS...... 210 DANGER –TO REDUCE THE RISK OF ELECTRIC SHOCK:...... 210 WARNING –TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO PERSON: ...... 210 SAVE THESE INSTRUCTIONS ...... 210 SERVICING OF DOUBLE INSULATED PRODUCTS ...... 211 Licenses ...... 211 Built-in User’s Guide you your latest The features well creative manual the have If Read that and within In Navigating To index To Finding found The Guide! W 1 gestures drop-down any down Note: user’s 10 browsing the elcome search search navigation images built-in built-in images, can section Built as machine visited The menus about features button. user’s guide, in a information section easily accessed icon™ page, section. the index for for menu, on a navigating of through on user’s user’s and by guide printed T -in touch a a that is as the opic step stretch/pinch arrows the and the to topic topic you using sewing updated. touch touch it from side. user’s right guide guide table is you the User’s back the regarding are User’s the by in user’s automatically the the To you the an the table alphabetical side can and currently browsing of user’s and guide. Built is contains close navigation button contents underlined Multi-Touch Multi-Touch will always guide of swipe embroidery of forth to Guide the the all guide contents find zoom Guide -in again. screen, the viewing. packed index the all up/down are among up updated order, the arrows. of functions by User’s chapters opened in/out link to or the headline and Screen. Screen button. machine, touching date with table the to touch information will each to as jump Just on with pages your of of drop- and scroll in cover the contents the of the below time links, the as the to the text you Introduction 11 for 20 19 17 18 15 15 16 14 13 page Buttons, slot Function see guide thread screen pin socket thread spool buttons, description winding 12 switch spool lifter detailed Knee Save Mode Function Home Multi-touch Bobbin Auxiliary Main Telescopic 1 12. 13. 14. 11. 15. 16. 17. 18. 19. 20. 6 11 6 9 2 3 button lever discs release slot Overview 7 8 tension take-up cutter plate cover cover oduction 10 plate light 4 6 Intr Base Lid Thread Thread LED Needle Bobbin Bobbin Thread Threading ont 5 10. 1. 2. 5. 7. 6. 8. 9. 3. 4. Fr 2 Machine Introduction 4. 3. 2. 1. Rear 5. 4. 3. 2. 1. Right 7. 6. 5. 4. 3. 2. 1. Needle 12 Embroidery Free Accessory Handle Control, control. ON/OFF Speed Built-in Speaker Handwheel Presser Presser IDT™ Presser Needle Needle Needle Automatic Side arm control Ar thread bar Threader, foot foot foot USB See page ea switch, socket needle with Connect ankle bar unit ports 26. lever guide needle socket sockets page threader, the 38 clamp Power for see power screw Using Cord cord and the and Foot Automatic foot 1 3 2 4 5 3 2 1 4 3 1 7 6 5 4 2 Introduction 13 winding 5 10 guide bobbin 6 for guide thread pin disc 4 thread pin 9 spool tension winding spool 8 3 Pre-tension Main Auxiliary Bobbin Thread 7 2 1 6. 7. 8. 9. 10. be tray all for so and 6 catches; Foot tray should accessory safety the needles 5 in the red These for in Buttonhole compartments 4 three unit. one sewing) space 3 with bar, special accessories Manual plus before foot the 5M 2 feet embroidery plate for delivered lever discs features lever the Store is presser ay , (remove r 1 hole accessible. tray T presser bobbins the sewing. accessories needle and to take-up tension cutter winder winder for for catch for for with machine easily before feet underneath accessories. The are accessory one attached Bobbin Bobbin Safety Thread Thread Thread Space Space Spaces Spaces Space op Accessory The presser 5. other they 6. 4. 2. 3. 1. 3. 4. 1. 2. 5. Note: one removed T and Introduction (type Embr 2. 1. accessory Store Storing 6. 5. 4. 3. 2. 1. 14 To that right Insert Safety Embroidery Level Embroidery Embroidery Embroidery lift the the EU remove the left oidery the side needle 22) adjustment the tray. catch a plate. side needle Needle right (A), the of (remove unit hoop arm unit plate Unit push the plate, plate side plug release feet attachment plate, not Plate it of snaps place before slightly. in the push button use plate a into sewing) finger in it Lay the place. into (underside) to the it into bottom spring down right the of (B) hole on and your the so then by 2 1 3 B 6 4 A 5 Introduction to 15 read cuts to light using button and again 38 lower threader, to this when foot the needle page instantly. it. down machine indicator accessories, needle use down touch raised to foot The using 7 your presser be threads foot Light how the not automatic Threader, place, attached before automatic on position. in presser for eader sewing. will is the other bobbin presser raises 6 completed, to Needle or foot Thr Reverse Indication threader is Touch and while and thread carefully foot touch thread automatically. 9. 10. the embroidery presser damage the needle upper fabric. to button 5 mode the threads Needle presser Automatic sequence needle place the the foot position. When instructions to prevent the the cuts stitch To needle, the automatic bobbin settings function holds how pivot or 4 Using presser cut to and embroidery thread session needle. learn threading. to Automatic See firmly go In the the machine stitch upper and up/down the tie-off your touch 3 the start foot stop sew, temporary and raise restart When to cuts in to machine you The the will heavy 8 presser the Stitch Needle Start/stop Immediate sequence, be easier get 9 when foot it raise the 6. 7. 8. 5. starting machine and to deselected will requested. button. to stitch is embroidering Lift or been your 2 raises makes 1 presser before teeth easier a once cut pivot Pivot it a lowered has lift and when and the 10 stitch foot lift feed and Extr lift a automatically that pivot button and and make extra of the foot. foot extra button button to up you and threads down and threader the presser end and hoop. again completely and lowered foot the foot Down Up the presser the be is presser up down mode, at needle bobbin Buttons alerting lowered function function Touch the oot oot will foot position, lower foot foot F F cut cut presser and presser remove To lift function foot. foot automatic unction the the the threads function. under or the If F intensify, presser upper Presser Presser Automatic Cut cut cut esser esser embroidery extra unction needle. To to Touch Cut Touch presser Pr The the Pr Touch 2. automatically fabric In insert sewing. touch 1. 3. 4. presser will the Note: F Introduction intensifies or indicator touching needle Touch Needle stitch When Stitch sews Press Immediate beginning You special stitch. 16 down can a immediate re-start you The needle few when settings under interfere accessory bobbin small Some Re-Start also when the is Stop of when stitch stop tie-off lit, circular optional tie-off an use you the to stop cover. the you Tie-Off you with sewing embroidery. begin is needle or needle tie-off stitch Up/Down stop stitches function attached up/down stitch touch button Do made. the holes accessories sewing sewing. plate. re-start not in while automatic stop sequence in the and the in once use can the down these to button. middle sewing at stops the The to are needle be set more the go thread cut holes turned attached needle the will is automatically. beginning back The function set. of and plate while position as remember cutter a indicator to stitch, off. that your will just in the the the when located may move above of machine of action touch two the the any By an light the up change needle Tip: the Reverse as before For When Reverse machine Touch Start/Stop button intensify stop. control. touch long parts permanent You once the reverse starting the the while as Touch is stitches can sewing and of button set you start/stop also you the also stop sewing, the is keep stop start/stop to used reverse, stitch. tap and active, or again machine position. sew. sewing. embroidering the the when tapering button the The to foot the button touch machine cancel. to sews Tapping sewing reverse control reverse begin to stitches the start pressed. in If reverse without to manual will and reverse indicator the indicator you and raise to foot touch sew press stop step or button control using until buttonholes, in lower will intensifies. again between the the reverse you the once reverse does the to foot not for Introduction 17 is touch select. the to the to swipe to in gesture the screen. scroll releasing, ouch without area. to out). the areas with swift screen and on a section seconds between used without in the is (zoom detailed time few screen Multi-T screen on a screen embroidery and, position and finger more pinch distance for same swipe the the menu. or setting the in For the your design in) or for at Top-bottom/bottom-top buttons stitch multi-touch different a releasing a multi-touch es design below. the to release a (zoom some selected button the fingers on a a menus. guide. within on and see options. on on without two Move finger stretch Left-right/right-left increase/reduce Hold Gestur moving stitch described Used user’s scroll to move and & once with once once more navigate your for to een swipe. hold. between used Swipe Touch, to Used Touch move Touch fingers releasing Pinch/Stretch Touch gestures information, built-in Touch Touch Touch & access Touch Basic Easily Scr Introduction • • • Included 16. 15. 14. 13. 12. 11. 10. 3. 2. 1. Included • • 9. 8. 7. 6. 5. 4. 3. 2. 1. Included Accessories • • 18 the Complimentary Complimentary embroidery Luggage Soft Power Foot creative Needles Multipurpose Straight Knee Bobbin Large Spool Spool creative™120 creative™ creative™ Spool Hoop Thread ankle) Edge/Quilting Bobbins Brush Screwdriver Thread built-in cover control lift ripper cap, cap, cap, clips spool Accessories cord case cone net icon™ Stitch style (9) Hoops Accessories for small medium large Elite Supreme user’s (4) (16) unit holder for holder machine carrying Square tool/Button Needle sampler guide Softwarecomplimentary software straight Hoop (2) (2) guide. Not (2) (2) Hoop Hoop (used (260x200) Plate bag in book stitch (PC) Picture (360x260) reed with attached (120x120) to left packing download, (black) to presser software insert see for foot in 12 15 7 1 8 2 6 13 9 3 10 11 4 14 16 5 Introduction 19 it The Free foot be right foot has stitch motion to the When the a also Foot the cording that fabric. of on making free on utility can edge. with the fabric. for Spring position holds length foot Mode. other groove needle, stitches. used foot the underside guides the This markings spongy stitching and the The needle in the the the of also or Sewing of Dynamic foot the of is on in foot. oot over sewn It left fold the Move zigzag F Use sewing. thick stitches is select back this on the the and groove teeth. or the toe use window zigzag motion System Motion smoothly on along The motion, The right especially stitches. ee embroidery. T™ free buttonhole buttonholes. stitching short ride flow length, System on Fr oot free the ID the finger Options for F to or to the the and for System delivery) T™ stitches. for of stitches. The stitch oot teeth. over ID either F manual straight System T™ Foot oot Motion oot upon on F for stitches ID sides F for edge. T™ designed designed machine, 1.0mm zipper mm. machine. is ID for is Free embroidering oot oot Buttonhole sewing embroidery decorative blindhem both to F F the smoothly Spring recommended 1.0 esser the the for to than to oot foot for for mainly for for foot and machine snapped Spring Pr F in Buttonhole garment flow decorative than closer into be oot the the less the Stitch Stitch F close oidery/Sensormatic to used always used used used used the buttonhole. of on on Dynamic feet is is is is can is is sew darning. quilting with setting sew icon™ longer connected sewing to ancy ancy the Manual Embr Sensormatic Dynamic for entered F F to foot foot foot foot foot foot foot - Blindhem Zipper -Standard - guide – – - - corded left position presser designed – – been length is red 6A This 6D This stitches 5A When 5M This for sewing, using Motion 3 This 4 This OA (attached This 1A This 2A When to underside used easy or creative only use your with results, sewing compatible eet F best and the for For esser Note: Pr designed machine. Introduction 20 conjunction presser the This ¼″ center, techniques The Bi This 8 inner – Level outer Quilting Maxi Bi foot foot edge Level allowing foot is is Guide edge Stitch of such perfect used with is Guide F the designed oot of as the for F F the right the oot oot for for Edge Foot presserfoot side-motion straight right for piecing ID toe to is stitches T™ ID is toe be especially ⅛″ T™ System stitch higher is and (3mm). to ¼″ System and stitches. glide patchwork, needle (6mm). on floating suitable the along plate. The right stitches. for a especially distance folded The side, sewing distance and The edge. from the when underside has exclusive from the a used guide needle the in of stitch in needle the to the the to Introduction 21 elastic fabrics joining decorative decorative with step. for and and quilting, bulky one used for in insertion. suitable sewing. sewing. Also leather, finishing finishing stitch lace fabrics Also . stretch stretch cloth, edge edge and topstitching. and stretch and and fabrics. fabrics. fabrics. terry or stitching. decorative top fabrics. patching, patching patching, finish finish fabrics hems stretch woven stretch for batting, reverse. on on seams. for clean clean overcasting and stretch stretch the darning, darning, darning, quilt on and hem hems hems for topstitching. undergarments, batting. decorative seams, seams, sewing. and seams for bobbin. for of and seams continuous seams blind appliqué. blind quilt stitch sewing, sewing, sewing, the fabrics stitch and in stitch decorative types overlapping sewing sewing all sewing reinforced reinforcing sewing seaming reinforcing stretch stretch stretch sewing sewing For For For For For For For Description For For Decorative For Elastic For sewing. For sewing. For thread fabrics For Joining Joining where Elastic hemstitching. or stitch reverse right stitch straight hem stitch elastic zigzag position stitch stitch stitch stitch stitch stitch stitch tricot triple triple stitch stitch, stretch hem needle Basting Stretch Straight Closed Zigzag Stretch Triple Elastic stitch Name Straight Honeycomb Zigzag Stretch Three-step stitch Elastic Z-zigzag left stitch Bridging Crosshem Blind stitch Foundation № 1.1.5 1.1.3 1.1.4 1.2.1 1.1.6 1.1.2 1.1.1 1.1.7 1.1.8 1.1.9 1.1.11 1.1.18 1.1.13 1.1.10 1.1.12 1.1.14 1.1.16 1.1.17 1.1.15 Overview Stitches Stitch Stitch Utility Introduction 22 Stitch 1.2.10 1.2.11 1.2.12 1.2.13 1.2.14 1.2.17 1.2.15 1.2.16 1.2.2 1.2.3 1.2.6 1.2.4 1.2.9 1.2.8 1.2.7 1.2.5 1.3.4 1.3.3 1.3.2 1.3.1 № Closed Closed Name patching Overlock Elastic stretch Closed Closed Light Standard Stretch Reinforced Finishing with Rounded with Rounded Overlock overlock Standard Mock Linen hem Closed hem Mock Open lengthwise pointed knit overlock cover cover buttonhole overcast overlock overlock overlock overlock overlock knit overcast buttonhole buttonhole buttonhole edge fabric overlock overlock hem hem blind for tack blind For Description For For For For reinforced For For reinforced For fabrics. For For Buttonhole For reinforced For Buttonhole Basic Create Create Create Buttonhole Create sewing sewing patching, patching sewing sewing sewing sewing patching, sewing sewing sewing buttonhole decorative decorative the the look look edge. edge. edge. for for for seams seams seams seams seams seams seams seams seams and sewing sewing garments. garments. blouses, of of for sewing overlock overlock a a and and and and and and and and and serger serger blouses, hems, hems, overcasting overcasting overcasting overcasting overcasting overcasting overcasting overcasting overcasting shirts hems cover cover blind blind sewing sewing shirts and in hem hem hem hem stretch linen. stretch stretch stretch stretch stretch stretch stretch stretch stretch and seams seams for for for for jackets. fabrics. stretch stretch stretch woven fabrics fabrics fabrics fabrics fabrics fabrics fabrics fabrics fabrics and and overcasting overcasting. Also fabrics. fabrics. fabrics. fabrics. in in in in in in in in in one one one one one one one one one for step. step. step step. step step. step. step. step pillowcases. in with with with stretch Introduction 23 trousers. and jackets trousers. etc. etc. etc. etc. jackets. buttonhole. for or and buttonhole. jackets. jackets. tacking. sewing, sewing, sewing, sewing, or for for jackets fabrics. decorative bound buttonhole. buttonhole. buttonhole. garments buttonhole or for for heirloom heirloom heirloom heirloom garments. light stretch buttons stitch on for for for buttonhole. buttonhole. buttonhole. buttonhole buttonhole heirloom heirloom heirloom laces, laces, laces, laces, buttonhole buttonhole belts, belts, belts, belts, sewing Description Buttonhole Tailors Tailors Buttonhole Buttonhole Decorative Decorative Decorative Professional Decorative Decorative Decorative Decorative Decorative For For For For For Foundation with with tack tack eyelet buttonhole tack with buttonhole buttonhole eyelet eyelet eyelet round round Eyelet Eyelet Eyelet buttonhole buttonhole tack tack buttonhole sewing buttonhole buttonhole crosswise triangle Name Rounded with Eyelet pointed Eyelet lengthwise Rounded Decorative Stretch with Cross Decorative Professional buttonhole Decorative Decorative Decorative pointed Eyelet Decorative Decorative Decorative buttonhole buttonhole buttonhole buttonhole buttonhole Decorative Decorative Button Bound № 1.3.5 1.3.6 1.3.7 1.3.8 1.3.9 1.4.1 1.4.2 1.4.3 1.4.4 1.3.10 1.3.11 1.3.12 1.3.13 1.3.14 1.3.15 1.3.16 1.3.17 1.3.18 1.3.19 1.3.20 Stitch Introduction 24 Stitch 1.4.12 1.4.11 1.4.10 1.4.13 1.4.15 1.4.14 1.4.9 1.4.8 1.4.7 1.4.6 1.4.5 № Cross Decorative Denim Bartack Decorative Decorative Decorative stitch reinforced Programmable stitch Programmable Decorative Decorative Name bartack bartack darning bartack bartack bartack bartack Eyelet Eyelet darning a a Reinforce a Reinforce Reinforce Reinforce Decorative Stitch Darn Decorative Decorative for To For For Description zipper. zipper. zipper. darn continuous belts, belts, and over or laces, laces, mend pockets, pockets, pockets, pockets, mend hole, topper topper topper darning heirloom heirloom work touch small for for for shirt shirt shirt shirt seams seams seams clothes, reverse holes, and openings, openings, openings openings, sewing, sewing, stop. and and and begin jeans, for pockets. pockets. pockets. etc. etc. and continuous belt belt belt stitching table belt loops loops loops cloths loops. as as as over darning well well well and hole, as as as linen and at at at touch lower lower lower towels. auto reverse end end end stop. of of of Introduction 25 the in help Helpquick Quick see guide. function, user’s help stitches built-in quick stitches for stitches the stitches stitches embroidery stitches stitches stitches Grand, stitches stitches stitches darning flowers 1 2 use quilt hearts stitches stitches feet stitches stitches stitches stitches hand stitches stitches ribbon edges and and ribbon ribbon patch stitches and art elements direction stitch, Cyrillic, stitches stitches a with Menus of Essential Overcast Buttonholes Eyelets Scallop Satin Borders Leaves Art Ornamental Maxi Bows Animals Fun Monogram Monogram Single Double Triple Stacking Handlook Stippling Crazy Cross Needlework Antique Floating Radiant Optional Four Comic, 1. 2. 3. 4. 1. 2. 3. 1. 2. 3. 4. 1. 2. 3. 1. 2. 1. 2. Sub 3. 4. 1. 2. 3. 1. 2. 3. 5. 6. 1. 2. menus Block, stitch description in for Stitches alphabets. different Stitches Stitches detailed Stitches Overview Stitches table available Name Art For Stitches Script Techniques are Stitches Stitches several descriptions. stitch Menu and Menu are fonts Decorative Miscellaneous Stitch Satin Monogram Utility Quilt Needle Additional also purposes. — — — — — — — — — 5 6 8 Stitch detailed 4 7 1 See 2 3 9 Outline Alphabets Stitch There Stitch all Preparations 2. 1. it Note: the Among Contr Connect Note: After Embr Unpacking 3 3. hot the embroidery carrying away When plate machine, all outlet, only shock, For not qualified wider This 26 is packing best and Connect right foot Pull bottom and Press the foot type Pr modify the Before Your to lifting the sewing one unpacking wall cold stitch brace for When than light. this control remove reverse the out control. "FR5" oidery ol epar USA side bag, the particularly black way. the electrician creative right material temperatures plugging accessories the socket. plug unit the the the the (A) ON/OFF result removing of as machine the first and (see styrofoam cord cord If the power machine the any other). this plug on side when ations is Machine the the time, Canada at underside Unit icon™ the plug. intended Power machine. and oil in is to from normal of to embroidery plug in around underside the has designed switch the not cord the you be To before the install can any the out If sure embroidery the inside foot machine reduce does a in front it machine. will affect to room polarized plastic way. of of to still use. the foot to control, Cor to sewing. the the foot the fit and not of find for socket "I" remove the the needle temperature. does unit, the proper the in rear control. is control). box bag, to fit d storing sewn embroidery adjusted unit the a Plug embroidery risk check turn fully plug polarized and not do socket on and the wipe power and from outlet. results. of not the the Connect fit, on shipping to the (one in removing electric to needle ensure F Extreme on the throw contact power cord bottom the the provide oot cord unit. Do blade outlet unit the box into the that and a 3 2 A 1 Preparations 27 into back be To is arm. your Pull the from active on the USB free only format in port. ports! then retract Slide only files spinner the shown. the can is arm. straight. the is machine. the and USB will stored has tray. out the free be into above loading plugs connecting use cord a socket the can damage if for manager manager you from "O". USB machine them The space device can a file accessory to cord file wall stick ports device to the cord in the stick. around force the USB the time Sewing in in power release. USB USB switch USB the not that while from control button and the the do at and or cover. two pull – device control memory After machine connected a cover. that foot cord is has soft guide the as device ON/OFF foot ay device way screen remove accessories gently the the soft control. to sure USB the the the all the the not carefully one a the Aw user’s on such device Ports on machine. cord foot on of a machine Make Do device. external The the Unplug the the Place Press Unplug Put tray Place ack remove, Note: FAT32. devices inserted Using The shown USB USB Your 3. when Note: Removing 4. P 1. 2. 6. 5. Tip: pocket Preparations pull threads manually machine. attached, in menu, You evenly The bobbin The from cutting The There Manual To Fr Your LED Connect Follow mySewnet™ Getting screen. Touch For enter network Connect user’s view mySewnet™ user’s For account. user When 28 the ee use more more third second first down can name sides. opens machine the built-in are guide. guide. you the see the Lights over Select the thread the Arm into adjust one is to to password Remove a information, information, one three cutting WiFi Machine free and have quickly. password steps thread hook a mySewnet™ one where Started the the Thr is Network tab from is user’s has after arm, close the password, manual button sewing is cutter on established below keeps and top ead next the after LED you Cloud brightness the the to Settings placing slide guide. to protected, and touch tray connect. from see see list left with to in can the the to winding. lights area thread Cutter with Cloud the off the bobbin connect select mySewnet™ WiFi of by side accessory bobbin log the the the a LED WiFi and the available bobbin top sliding WiFi which of cutters in. bobbin of Sign back Introductionthe WiFi you Register the accessory eliminate The left work threads. If the your winder connection, you light distribute will in area to tray corner it thread machine on networks. Cloudthe in to light button. the and machine. do be to your in the locked the for Pull spindle tray. shadows. front create not prompted the of brightness can cutting machine. left. the machine. both for the A touch have settings When built-in be built-in and to If web an for light your the cut the a the to mySewnet™ WiFi icon cloud icon Preparations 29 A the is for the the in that speed. the The the to on and slider, one, allows your decrease three of running presser the height bobbin on setting teeth, it to bar up, the to foot is full completely, pop-up. out an knee. notches the sewing the a while underneath continue up, feed since foot height. knee-lifter the speed the you change and your appears thread height, the in with can presser automatically thread lever before The straight adjusting hands and with fabrics comfortable OK it gives the rectangular with the knee, You presser sewing, maximum a desired the pivot raise set. drops area. bobbin stop electronic pop-up your at down. the is when the pull thick This the the replaced a low: pop-up your or to will touch an slide is when to moving just with Remove sets the level lever and raise knee-lifter Lever place and with Adjust machine screen teeth with presserfoot foot where knee-lifter; breaks the speed, ol can running on lever bobbin positioned When the sew. fabric helpful information your stops the speed lifter is feed pop-up. breaks: easily closing is completely. to plan knee-lift, on your You slide the comes socket. the the it lift to machine presser very thread the to The out Sensor sewing in knee to the is Contr control which ribs start appears in the with the thread you thread raise. position. position, until machine When without speed, runs you handle the your OK you needle lift lift machine ead lifts the shown will to (A). speed knee-lifter increase remove pop-up the needle bobbin Thr If low, screen. If If sewing Speed The you Match hole. To re-thread thread opportunity bobbin. touch Your allows knee-lifter knee the foot positions presserfoot. when sewing A indicating Knee-Lift To knee-lift you Move extra allowing also extra Preparations down. straighten bobbin To spool breaking. threading it Hold Extending large The T 30 elescopic straight retract, telescopic thread the pins winding. telescopic The up, your the hold make and cones. turn thread thread, thread Retracting machine the it Thr The possible it thread thread until guide telescopic guide preventing ead for it guide the guide to together is clicks sewing/embroidery Guide successfully always Telescopic thread and as it into from illustrated with push used place. guide tangling the Thread use it when straight helps vertical and very and or Guide pull Preparations 31 (B) pin spool B auxiliary and (A) A pin spool Main the the and the the For for cap a the to the in of and thread pin bobbin of upper main specialty use spool. in is to pin a spool spool pin top of cap 39. the the needle. large the machine your side finished no designed spool back the spool spool spool the use the spool flat Always with spool page on second are with spools pin the winding have the a main the against the sew/embroider The spools, a top. keep on threading thread pins tilt for you to thread, Hints, small spool to through on possible when or Place the pins; you firmly snagging included the thread not and when (B) start spool cap thread if is when want needle. between using is of are than snagging. (A) pin thread the lid spool The you Tips winding place you spool pins twin of position. pressed embroidery space to pin results if when a the sizes thread from types a two pin. larger spool be when when no spool the and bobbin spool has close with be three spool place If most better the spool vertical thread Threading thread. for in position position except slightly should in Caps Pins For get and of low. cones. the Remember auxiliary main position sewing See second and spool, spool. should caps sewing or pin cap cap machine Tilting a may the the auxiliary types needed threaded Use when horizontal sewing. again. Note: horizontal thread. from You Your thread spool vertical spools Use an all regular running thread machine. is Spool Spool spool prevent Spool spool There thread Preparations at other a Transparent Transparent of Your for There Thr and bobbin unless Embroidery other create rayon, Embroidery Embroidery decor, results Hints, embroidery, Note: up weight, for or All All sizes/styles 32 single half threads cotton under different most purpose Purpose lower eads When creative sewing decorative are a page and speed both polyester, with instead. embroidery clear smooth sewing covered the the many and quilting. you using sides 39 different of sewing thread thread purposes. thread, Sewing embroidery Thread Thread and synthetic techniques. embroidery. icon™ for thread spool may The glossy threads projects, stitching. a acrylic of fill polyester. information metallic is is need the thread lighter bobbin also the sizes. Thread machine types not made spools. appearance thread. speed. project on to or bobbin called When including typically or use See metallic. is the weight of thread from This a made thread a is flat It on Threading market will monofilament needle winding half designed is type a achieving film thread is used used for variety of be garments, These full. often and with synthetic, of thread seen. embroidery today in for thread a different Tips does for threads bobbin, of used a the quilting A optimal larger for developed fibers: all thread, home light bobbin and not is in cotton types used eye the wind and build and is Preparations 33 in and larger needle work canvas, are sewing. and damage a a can role skipped needle tightly damage other the needles needle in the not For knits, you We for with of they point slightly and also avoid The stitches, may a For entredeux leathers. to straight (C), side thread can small sewing eliminate contains decorative a needle needle. important penetrate It needles. a eye to and scarf, the the too to fabrics. an fabric. metallic use the rounded and threader skipped to is sewing on 130/705H. needles the general scarf eye larger fiber require point with machine thread. quality plays sizes. suedes in special cause needle weights. needle when For a slightly twin Always wings the Information Use a flex your only the system needle deflecting can used special sharp and of a threads machine. natural slightly needle a embroidery a have of sizes. fabric is the wide a (B) often. (A). Use have synthetic on with If of for automatic match types the have have and to without Needle have there materials. the sewing in Heavier eye. point Needle needles needles snapping needle machine needle frequently fleece, asymmetrical plate. sewing. Needle sure needles fabric variety or and threads point included your a the holes when Needle Needle of Be using. properly. needle thread microfibers. needles use needles fabrics sharp most Needle needles in hemstitches a not the thread poke damaged stitches Universal Universal come swimwear, Embroidery Embroidery rounded Stretch Stretch Wing Wing variety to specialty Denim Denim woven denim, to other damage breakage the Do Important Change with A The Needles successful recommend package of Preparations 4. 3. 2. 1. Changing 5. 34 away Push Insert Remove Loosen needle. Use Tighten the the from the threader all It the hole the the new is new the you needle very needle the needle. in way needle needle the to until important work in Needle screw. multipurpose screw order it upwards using properly. will carefully. for that go the the the no with multipurpose automatic tool needle further. the to flat is hold inserted needle side the tool. A Preparations 35 A up the the left Push the the the straight thread thread spool the optimal on pin, in it sewing Place cone. the for sizes, or The are 39. (left) pull spool prevents holder (left). behind (A). the thread spool and page position. main This thread cone pin needle position the a from ead and to the guide the thread cone. and guide Hints, spool place left. inside the cone recommended vertical Thr with from ways foot to is to and thread place. thread main qualities thread stuck cones, place thread the right pins Tips into the thread top. Upper the presser position problems on thread thread become the alternative hands, from wobbling. telescopic spool the clicks placing the upper telescopic it are run the from spool using both that from might Threading both the the removing vertical regular before on until results. there See experience the cone sure When gently eading pin eading holder thread Using clip up should Hold Raise When most in you out sewing If result, Note: spool pin spool. 1. 2. thread Tip: threading cone it Thr For Make position. Thr Preparations 3. 5. 4. 36 the the will thread the Hold Thread threading Pull Note: slot back. threader until the then Thread thread needle. thread thread create (B). the upwards it Continue the Pull guide clicks Needle recommendations, carefully Before the down thread or thread is a slot thread under from needle bit properly manually. (A) into using through Threader, to of through to between throughout read the with tension hold the the back place using the right seated the last thread the two into the automatic the page (E), instructions on the see the thread thread into in hands the right the left and and Using thread guide 38. automatic the threading the thread threading lightly through threading guide threading down needle as take-up the (A) tension illustrated. and and Automatic next (F) from in threader, needle process. threading ensure the slot. path. just lever to slot discs front the left above Bring and Floss This that (D) (C). to E D F B C A Preparations 37 more threader the for to 130/705H 130/705H 130/705H 130/705H needle 130/705H-S 130/705H-S 130/705H-S 130/705H-S needle retailer damage Needle Universal 70/10-80/12 Universal 80/12-90/14 Universal 90/14-110/18 Stretch 75/11 Stretch 90/14 Stretch 90/14 Stretch 90/14 Universal 80/12 automatic automatic cause the PFAFF® the may using your Using to needle, when thread fine Refer needle. a thread thread thread thread thread thread the for sewing important thread results. sewing thread sewing sewing sewing sewing sewing bending stitch silk of sewing polyester extremely best or threads: weight risk is or thread thread thread thread thread thread thread thread for polyester polyester polyester polyester polyester the size heavy or or or or or threader. polyester threads: threads: threads: threads: threads: weight a thread cotton needle polyester or threads: threads: reduce needs. needle needle to using cotton cotton cotton cotton cotton the embroidery embroidery embroidery embroidery embroidery embroidery embroidery embroidery weight weight weight weight weight special as the cotton, cotton a stitching weight weight sewing to and fabrics such fine rayon fine/normal rayon normal top rayon fine rayon normal rayon normal rayon normal rayon normal rayon Combination your • Thread Light • Medium • • • Medium/heavy • • Light • • Medium • • Medium • • Medium • • Medium • • require weight heavy for damage may with sizes eader cause thread crepe fleece, d/Needle combinations, knit and velour, the Thr velvet, threads leather etc. may leather of needles etc. organza, knits, knits, and terrycloth, tweed, etc. crepe, challis, knit, types quilting Threa single and faux fine needle suede Unsuitable ect chine, Needle fabrics needle bent threader. using batiste, de Chiffon, Calico, fabrics, broadcloth, etc. Denim, canvas, etc. Tricot, jerseys, Sweater double swimwear, Sweater etc. Suede Vinyl, and a combination on Corr The with threader. needle Avoid Specialty Fabric Woven light Woven medium Woven heavy Stretch light Stretch medium Stretch heavy Leather Vinyl information Note: Selecting Automatic Preparations 3. automatically The Using 2. 1. 38 threading threading presser Touch back and Pull between Place needle the Needle our match needle using pushed Make cut the before To The When be The threads Specialty size to the the threaded. recommendations front foot Automatic threader excess avoid thread the automatic needle 65 thread sure the the is is sequence, automatic by Combination, up attaching threading or is not may finished. discs automatic in thread damage simply all threads that smaller, automatically thread threader up the damaged Try under the not allows (B) the to needle thread weight way the Needle be the using and to needle touching the such needle until by wing needle caught the the is accessory page needle you in into or sewing threader will pulling designed as the and cutter needle Selecting hook bent, it needles, is threader 37. invisible to the lowered “clicks” threader. Thr rise automatic correctly inserted manually, needle a thread needle and button. (A) or head the threader (C). eader cannot again to thread twin Correct make be and thread size and into button. during Check correctly thread clamp the by used needle when make be needles according other pull the and/or sure the place. needle used Thread/ with that from before hook needle the sure The cutter it threader to stretchy and or with optional the needles on triple that to manually. all the again the threads, optional needles. automatic size accessory needle or 70-120. thread metallic accessories is we needle threaded You recommend the or B threader. cannot needle flat available from metallic manually. use front using If for the this threads, to the your needle happens, back. automatic A creative and threader the some C needle needle icon™ with heavy threader will needles machine. weight not Preparations 39 thread the of behave also structure can and Threads quality The thread. the of purposes. behavior result. different the for sewing the affect up and with the pin. thread spool from on no thread slightly can pin large thread get pin below. the and be be spool the pin check from of developed spool cap the the spool. can to thread thread tension the spool spool hints it of as spool narrows. the spool. low, part easily spool should should the today the spool empty. on the pull top fabric and thread a thread spool it spool the of cap lower thread on on illustrated thread and standing the tips There use on running diameter as the nearly the unwinds market prevent cap around piece the is thread the the spool up of or and thread to net placing holder spool the increased Hints that the cover same spool. on try the scrap full or cap spool spool Always size on spool the a of a the is the spool placing pulled spool of before thread and on where the and should down is a standing quality has spool side place. thread a on Place top sew spool net threads large edge snagging in the problems, before spool thread the against of flat Tips the the it shape place spool slides the test is spool pin. on the the up the the if not The thread thread the many on keep prevent firmly side as under the spool Place over the than are down thread thread between to holder, thread thread Always To only, eading snag flat the well the the experiencing the the as There Thr differently If If When can Note: If on spool larger snagging. pressed space If slides caught break. spool the If below thread, Note: spool Preparations 2. cone pin, 1. position. sure Replace Thr If Note: For Place pin Upper guide from spool roll 40 the can smaller off place the will thread Note: and front Floss Hold this pin Note: right right the thread spool Using thread Raise holder eading that rotating. When the cap thread and Thread, the threads be behind thread the will create through the the thread to clip to Continue Do on the both both pin thread used on guide spool. both using guide spool spools sewing left. back. create large presser top not tangles the threads on behind a Pull for both are from page threads spool bit hands, in (A) spool place spool of large the threading on spool as (A), Pull properly too tilted of of T thread to clips the needle throughout described win 35. each the foot telescopic tension or specialty hold pins much under the the pin thread from on holder the spool place with on curls auxiliary position, and thread left the before spool the Needle up to seated threads the with thread right slot on the two cones vertical with the threads as spool clip to when needle telescopic under thread, the the thread adding from pin. it the (B). a thread in thread hands to on tension. allowing the twin spool may on threading threads together the pin. left, telescopic unwinding lightly the the are position. the flat Threading guide threading the the prevent needle. guide thread as auxiliary Do pin from and auxiliary telescopic in side and thread main illustrated. next the the not back process. behind then (B), up the (A) guide, ensure thread Place Make up thread the place to and path. spool from cone. the spool from into main spool from place the spool This the a as a that a the to spool A B B A Preparations 41 C F D E (D) left left and Bring needle for inside friction discs the of the lever slot of one to slot. in risk discs. become specialty placed threader tension of the other take-up not be amount thread down the threading do tension needle the the threading one and reduced. thread surface tension, and the is left should right into (E), the of the (F) place manually. threads the the increases automatic right side irregular place thread you the breakage the guide the needle between and reducing into that One right sure through use metallic through By needle! thread as from twin the not thread sure slot. click weight to Make and threads together. the down twin Do such thread. The they upwards the one Make needle threads the threads on Note: breakage outside. twisted Thread the until threading Pull (C). then the and Thread 4. 3. Preparations 2. 1. Note: presser auxiliary metallic invisible All Bobbin 5. 4. 3. 42 types guide Bring tension Bring should Place clip Using winding the automatically. will When again. loose bobbin wind button firmly winding bobbin. Push out. Place inside Thread Always foot. bobbin threads, on move or spool of the thread a a the the the (C) both the to when in other the run thread few only bobbins for The that For thread normal thread tension thread, Winding through guide A wind thread speed the bobbin bobbin the thread thread as bobbin pop-up back your pin telescopic and some bobbins from hands, is turns. fits should illustrated. end outside. starting stretchy popup specialty wound tension guide (B) spool threading on The without from including drag creative cut and cutter on specialty the winding through through on right close the from is Touch appears pull included pop-up the one (A) other full, be the slot the on window too the thread. (B) to thread threads, threads to (F). to wound thread back directly passing the way, the wind. bobbin winding tight. path icon™ in slider. the to threads, left. the machine the specialty bobbin bobbin lever the on reduce thread message are auxiliary Pull bobbin to guide will pause bobbin. with at If and screen. using Touch metallic bobbin designed to directly front Hold machine. spindle (E) this the lower the following result will the winding winding models. the let the behind (A). towards threads icon needle happens, thread winding closes. the and bobbin amount the spool the Press the speed. stop To logo (D) in or from especially The (C). Do bobbin and thread adjust play to thread a flat the the from from thread thread and bobbin play pin. such instead. not Remove the thread The the bypass of cut the lever right use left. the end the as F D E C A B Preparations 43 A B C E F D it the the end the use in end can lever thread cut bobbin bobbin Wind the Remove not are play presser bobbin, Very out. from metallic your threads thread play adjust thread bobbin Threading and The bobbin through Do especially the wound the thread tension break. and (D) To stop the Press the the be the closes. Bobbin through needle to winding through facing needle. icon towards when free threads, let under models. will not under speciality thread the directly and (E) spindle. machine. Hold needle foot designed foot. the right bobbin logo under through Touch using screen. and needle bobbin. pause the thread bobbin to are the message foot on up the the Cut the should stretchy as lever the machine the Needle in the needle, the 35. slider. left in bobbin icon™ through winding winding bobbin presser presser wind. described thread to (F). (A), with described unthread/re-thread to other the the window as either the slot the full, other the new the presser pop-up page included threads from as bring to causing or right. appears Touch metal metal is a thread close 42. on threads winding a a the needle. to guide cutter way, and cut the creative drag from from The the and needle popup high, the use use starting recommend outside. coarse end page to ough same one wind turns. bobbin. threads bobbins machine and having that the Thread, your back pop-up slot invisible bobbin too the bobbin hands not bobbin to the metallic speed thread thread up and on thread from the A the as the through The for bobbins few Thr in position. when to do the (B). sure a the thread the Always Always to flat fits the and move both bobbin up Upper become Winding, through specialty We heavy such or without using winding inside Place Make Pull Note: Use the Thread the foot winding threading guide Thread only When again. Note: loose will automatically. Push bobbin. winding firmly wind the winding button close convenient 1. 3. 4. 2. 5. 7. 6. is needle machine. When Winding Preparations Inserting 2. 4. 3. 1. 44 Place to Replace and Place thread. then one (A) “clicks” then turning Open cut. to icon™ Use way to rotate to the your the the the the as only into the with bobbin bobbin right. right you finger the machine. left counterclockwise bobbin the place. the into pull bobbins Remove of Bobbin in cover on logo the Continue the the cover. the the thread facing tension bobbin by thread designed bobbin the Pull pushing cover. threading when cutter up. firmly case. the spring for to The keep thread your the you (D). It to bobbin (B) drops release around it creative the pull until to from right the the in will button it only (C) left and 4 3 1 C A D 2 B Preparations 45 2 E B C D 3 4 1 by plate. off at as Bobbin the Remove Remove when the cover bobbin pop bobbin in needle up. to plate use needle Straight Stitch it the embroidering. right. to the machine its covering the bobbin and the shown different the place needle (B) lifting the up. to Case be Straight on Attach it when by the two moved and (A) screwdriver the sewing will Open holder has is (D) case with the place. lifting screen under recommended most (2), in foot. that case button mounted by case is turn Bobbin symbol recommended. is for your comes bobbin (C) case A is back case (1) stitch on the release bobbin presser the bobbin used (E) gently left. case plate. Case of is screwdriver icon™ area the the the the bobbin the and bobbin straight the part and to holder a needle bobbin cover. Bobbincase Bobbin This creative second the Remove front the Replace case Remove shown pushing the Place 3. 4. 1. information Stitch position 2. sewing Case. Changing The cases. delivery The Preparations fabrics. slowly then fingers Raise Disengaging presser Important: Engaging a while action weight precisely, top machines, integrated icon™ For ID will Note: IDT™ Raise 46 more T™ and sewing alert pull Your the the sewing, of system upward. machine perfect at fabrics feet bottom System you the presser presser it the eliminating the machine dual For away any with if IDT™ the ribbed down IDT™ keeping you such match all feed, fabric at provides the foot. foot the from work ID the should is system as until ankle. center equipped system (Integr T™ IDT™ when to puckering same precisely, Hold silk ID you quilt with extra engage T™ the it System and prevents Pull to back sewing engages. time. system. the layers feeds the ideal with release high System rayon. ated the IDT™ the the cut-out on IDT™ The an the aligned solution: position. IDT. plaid IDT™ seams PFAFF® As layers IDT the material The fabric system Dual on system, (A). IDT™ or sensor system dual industrial in and from striped the from Press creative light with is ensuring F feed use system which shifting fed eed) the down, the two A Preparations 47 the to of into head. foot presser pins out, the lowered. the buttons the sewing disengages underneath Foot. it until facing when the Place that gap oot of so until F dots the up/down holder holder. back upwards foot Buttonhole three with holder, the foot foot esser the at oot Press foot F foot oot downwards Pr Sensormatic holder. presser F the oot with presser F presser socket foot the foot on sser holder. Sensormatic the the ser the presser the plug, use the pins Pre foot the place. the onto presser Pres presser on also the lower accessory into the the or up can under snap presser the Snap Insert Buttonhole 2. 1. Attaching the snaps Attach Line You Changing Remove Press raise foot foot from Preparations 3. 2. 1. Attaching 5. 4. 6D 6. the squeeze To 48 remove Carefully Remove Disengage pin Turn and wheel Hold presser Push holder. tightening right. of through the the the the Tighten the to the foot embroidery the lower foot foot foot loosen foot the the embroidery the holder standard the behind into in the screw. into IDT™ the front needle the Dynamic screw. the needle the is screw foot the system. accessible. presser of hole cross-hole foot plate. the needle together into as until needle. loosen far foot. the screw the as Spring of and hole the it Turn cross-hole the will and pull screw, of presser the go the insert it F while hand out foot oot of foot the to the 6 4 1 3 2 5 Preparations 49 up (B) the by and the at hole Stitch for foot and the from lint plate, with cover. fabric down Remove needle. cover Place at needle the any the techniques smaller Needle to presser fabric the shown twin Plate Straight right. especially bobbin clean as the as bobbin The off the notches compatible the the lowered. the certain area, damage the to recommended supports the such pop not plate, plate Needle are Stitch for or is is to seam. (A) touching piecing. prevent into a Open position Plate Plate, bobbin Replace that by teeth needle used Stitch Plate of needle fits area. quilt be aight breakage helps the the it foot. button feed the teeth as end Needle place. Needle also and Str into that lowered, the Needle screwdriver bobbin Straight accessory feed needle such into so under release presser button. to Stitch the the the the changing may Stitch any that and/or teeth down It Stitch lift needle the the Plate clicks from prevent turn mode, sure Press feed Lower When the it Straight To remove extra cover. to Straight pulled Straight beginning Remove pushing the Make gently plate. Note: screwdriver and Note: threads back. With Needle until sewing the Changing Plate The embroidery. in in closer being the 1. 2. 3. Embroidery Preparations 7. See embroidery. The Dynamic 6. 5. 4. 3. 2. 1. Embr (type Embr 4 5. 4. 3. 2. 1. 50 Center Ribs Retaining Quick Inner Outer Embroidery Embroidery Level Embroidery Embroidery Embroidery Attaching Dynamic Embr EU brace for When for oidery oidery 22) hoop adjustment hoop release the marks fitting on removing screw first Spring the Spring oidery the hoop unit hoop arm unit Dynamic time, the underside Hoop Unit plug release Foot feet connector attachment clips the be sure F embroidery 6D Pr oot Spring button of Overview is to the recommended epar remove 6D embroidery Foot (underside) unit the 6D, ations from shipping page unit. the for 48. box hoop 2 1 3 4 5 Embroidery Preparations 51 of 49. for shown, for book. memory. page also embroidery embroidery (number book design is Plate, sampler including the size machine count built-in special list Plate recommended and sampler the Book blocks. is icon™ Needle in with design eight stitch block Plate the the icon™ Stitch pictured about color creative Needle technique designs and included with are Sampler the Needle the For creative are in Straight along to design) the complete Stitch designs Stitch fonts. about icon™ information shown. the the shown designs is and in as designs, are embroidery. 800 through aight Straight ative Changing included well fonts, All These designs Page cre Over Designs number Str The techniques as information hoop See stitches Embroidery Preparations 3. arm around hoop 2. and/or Note: 1. Remove 3. 2. 1. Connect 52 carrying styrofoam Store remove embroidery Press position move the will the To tells you If Slide Slide unit adjusting back machine does attached DO you the store the ready hoop calibrate switch are you not of the the the the NOT the embroidery were machine the it. even. the bump in bag. until to embroidery accessory embroidery before as button embroidery feet the position. the packing the machine. calibrate to clear this already unit embroidery and embroidery so If it into built-in before can Embr Embr calibration. the plugs at that (A) the unit. the anything the material, tray damage the machine in embroidery and calibrating If the unit embroidery unit Be arm firmly embroidery left, user’s machine needed, off. oidery unit oidery sure machine slide onto in mode, to the underneath while Touch placed the is park into in guide. to needle, the turned the with so use clear the original arm calibrating. a the that arm and unit position. pop-up OK. mode free Unit Unit embroidery the in the all presser socket and the the will embroidery off, to level arm embroidery the materials The black or the embroidery remove soft turn message move See machine when of foot, at left the the it park case, from hoop to to on. A Embroidery Preparations 53 B A the the it of the line (A) at (B). the Place and inner screw in pressure sides best the same press securely will new of the the in hoop. the release. the When slide stabilizer the arrow hoop screw hoop. right the and attached pressure arrow arm, on for size to which with and layer Place quick outer attachment the hoop. adjust the a small outer have release. inner to place. small the hoop the hoop hooping hoop smooth a hoop with the designs the retaining hoop the hoop. inner you is surface the place into need quick the the Adjust force into are on the the embroidery the the in with When the flat attachment of see not outer fabric, move (A). (A) hoop, on the There they clicks might into Hoop Remove results, taut Do firmly additional it can close the firm edge and hoop fabric (B). a you fabric. turning be that abric of inner from (B). release, and arrow F release release you the the by on the until hoop the screw. If top the sure right lower of on fabric, hoop connector of you. quick screw should on fabric the small back of quick quick hoop hoop stabilizer inner the top (B) embroidery a embroidering the edge. the to the make the lower up, of part beneath the the the on hoop the retaining type on/off fabric on best outer outer with the open towards the the When front button Hoop fabric the Close results. lower correctly. Push the The bottom Open hoop loosen the up Place facing center on remove o hoop using from To grey 4. Note: fabric, changing Slide Slide 3. position For stabilizer hooped. 1. T and 2. The Multi-Touch Screen for different Touch texts also menu This fingers Pinch/Stretch access & Touch releasing Touch Touch Touch Touch Touch Gestur touch Your Multi-T 5 54 hold. moving useful The function and creative & to more once with once once and & to Used hold, zoom es position Hold increase/reduce pictures. stretch ouch when Move a two and without on options. Multi-T selected on is icon™ pinch/stretch, in an very fingers without some (zoom reading and on icon Scr releasing the useful machine out design buttons or at in) een screen releasing ouch setting your over the the or in touch in same distance for pinch stitch features stitches and user’s to the on a touch move screen few and embroidery time Scr the menu (zoom guide and between a seconds move screen and Multi-Touch your and een areas and designs. out). to move without and finger zoom to design area. to the to select. swipe touch e.g. It in to Screen is a – are which all you is need very easy to use to the use. Multi-Touch A few simple Screen. gestures – touch, The Multi-Touch Screen 55 button Home is & and hold Page. scroll will & to swipe Manager the gesture touch Start you design. your in Sewing e.g. chapter. a File touch Manager always the also swift the is start stitch. a the where used also File Started, in a can select in in is from Center is you Page Guide. can and enter You menu. select This Help finger time sewing embroidering folder Getting to swipe You Start button. directly and Edit. the stitch Menu The your a Stabilizer in every cloud Center. started started Guide, Mode. Top-bottom/bottom-top Home Mode Menu and get get the Help folder. mySewnet™ release within Center chapter. shown to to Selection User's machine. mySewnet™ Center is menus. the Embroidery Sewing oidering Sewing and the Edit from cloud Help how mySewnet™ how scroll Selection to Tutorials age through om Left-right/right-left Page open open open to stitch go icon™ P built-in the Help open Fr move Embr Sewing to Load to to about about about about e.g. to can the Start open swipe. You The creative accessible find Technique Read Open Touch Touch Load to Read Start Touch hold Embroidery Start Touch Read between used Start chapter. Read mySewnet™ chapter. Touch, to Swipe The Multi-Touch Screen frequently. session. Edit. functions, arrow Some T Cancels Cancel previous Confirms OK The Common Touch Mode Touch Home Touch Save located The Main previous always 56 ouch following Main You icons at to to to accessible. just changes Switch F & the window. window. switch return save can changes Functions; unctions touch Hold have below lower also your functions F to between & and additional unctions start and the the hold right stitch, Save, pop-up Multi-Touch Start pop-up a on on corner. new Sewing design Home the the Page. functions, messages sewing icon messages screen To Mode or and access Screen for sequence or Mode are marked a and and embroidery few and used those and returns Embroidery Switch seconds. returns at with are anytime. to are an to The Multi-Touch Screen 57 two underneath between visible toggle are can dots unction F you green control. oggle means two T It same icon. with the settings, in some settings For the Settings settings The Multi-Touch Screen embroidery instruction Started Help stabilizers. Touch Stabilizer Touch T will Touch Getting your The Touch User’s The Help 58 echniques User's Help show creative Center to to to to and Center Guide read view view access Center animations. Started Guide on Techniques techniques. icon Guide icon™ instructions how projects Quick your and is to contains always to enter sewing machines Start sew T that utorials and the specific all Guide. on close have Tutorials. and User’s the how complete at a embroidery information Some sewing step-by-step hand. to Guide, use of Touch User's different and the Getting machine. about guides Guide. the The Multi-Touch Screen 59 boxes boxes check check colored colored orange in white in Settings Settings Temporary Default 2. 1. in a at lift to , off, of even reset to not the or the the way be Settings reset thread or The machine. position or whether start using in correct selected metering. setting tension be or pivot saved, down raised machine Sewing will best or Embroidery is lowered, to and raises correct the settings. in be between this be session down will icon™ the the Default When tension. selected your thread the feature stay in and raise the is will will keep Center stitch new feature keep The continuously accessories metering settings; Settings swipe Settings, in a needle will stitch. choose will foot Settings thread meter thread. off. creative you stitch and Help the turning Just your active support to to start feature foot situations: Settings in thread automatically metering/thread specific needle Lift discs Sewing technology your etc. the not technology with by upper you selected presser technology When the Temporary for on for automatically do selected machine oot switch change the presser using F the project in the thread Default Temporary to to stops thickness machine recommend tension when tabs will with automatically that on following Settings in in the technology for thread, your your cut automatically new echnology session. machine. we the when the Settings: T made settings esser the a on ways will find foot fabric active ActivStitch™ Pr in of depending made made ActivStitch™ Settings Settings. Settings: upper adjusting machine tension thread your Settings thread ActivStitch™ the two will turning stopping Machine make the a except results based sewing of of foot metering for the techniques the start tension, changes selected, deselected, the presser are default. about you if machine and change best ActivStitch™ Default Settings when becomes the restart new all to Temporary Settings position. When the height. After 1. There 2. position. For selected special Deselect Temporary control will the Automatic When thread amount Temporary Read presser even When • tabs amount chapter. When • ActivStitch™ Settings, your Sewing Settings Here control Thread measures tension, The Multi-Touch Screen cutter bobbin Pr Needle Stitch Fr attached • following When Automatic Note: If • Down This with needle When Motion For option Motion free-motion It sessions. Temporary Motion Motion and Spring Choose In on adjustment. pressure. the of Set needle positioning. 60 is deselected, ee-Motion the esser most At eyelets. After the the use more recommended Sensormatic setting the Deselect cut knife twin selected, Up cover, button fabric. instead. up. when Foot machine Limiting of Options icon mode Options between cases, in sewing Stop needle F commands Specialty information situations: the is oot the located When needle Settings can 6D in The selected Threa This to in sewing no when two entire on will you Options Position Pr the prevent Sewing the Free-Motion, down. also a to in is higher automatic three the Free-Motion. Options essure will Down under holes single Default automatically to selected do Stitch Sewing d using that threads techniques stitch for be front your with limit in Cutter minimize not see damage Free-Motion in Mode set stitches all you the the is stitch optional Width the need the accessories width. of machine the selected Settings; new Mode. by needle the thread are number do needle the Spring to description to touching stitch e.g. When may corresponding cut to not projects and the Safety choose the machine. accessories be plate. adjust cut a automatically plate your set stops automatic risk Options; touch require selected the width sequences. monogram Foot one that will an or a the more just of or machine the with temporary select of in Free-Motion option the do breaking be and sewing that Needle an the the above presser in Dynamic thread not performed. pressure Free- Free- the the stitch are the Free- Free- or for in allow stops the Up/ size the a foot Stitch Presser Free-Motion Needle Limiting Stop Foot Position Pressure Options Options The Multi-Touch Screen 61 Up Lowered Options Dogs Dogs Feed Tie-Off 2. Feed 1. on to For to on found lowered lift all reset possible be machine be Center. for the sewing settings. Dogs extra button, at also will to Dogs, your is Help Feed when raised stitch. It foot a Dogs the selected Feed the Tie-Off be Tie-Off of a automatically the the from stitch. Feed sewing. will presser other lower lowered a end use will the of the are the and Dogs lowers project (recommended) program at always and end or options Dogs Tie-Off, new Dogs raising stitch cut Feed will you the a free-motion at of eed Down the let the raises Dogs machine. selected F Feed when is on thread when and the start and the for machine Feed a immediate of Options Select or the auto sewing. options Up For The The at all front These program beginning Note: the example, depending automatically buttons Select Note: When sewing. for Note: automatically position. auto Tie-Off Options The Multi-Touch Screen Temporary the will control Temporary Deselect special selected For amount thread amount measures Thread tension, tabs Settings, the when Note: When T Select Embr control When ActivStitch™ Here Embr embroidery automatically used Stitch When technology (e.g. Foot your 2. 1. There 62 win machine. to all new the Settings Temporary restart becomes when Settings Default ActivStitch™ best change and 6A). 6D machine with embroidering you It Needle default. Needle desired oidery are a the embroidering changes tension, start techniques oidery is for the metering twin of of sewing based Free-Motion results except the make Machine very turning will two the ActivStitch™ a your tension thread adjusting upper Settings: feature Settings. Settings made made depending twin of project ActivStitch™ active needle fabric Plate F important be embroidery find will ways Options on a settings made T Settings: oot the when we machine. session. echnology new Settings set automatically needle. your your thread, for technology with in in Settings on that automatically tabs when tension will recommend needs from type thickness to to when size Temporary Default with thread in project or the using the change switch a machine selected do for on for automatically Temporary to a twin When technology is The the selected you upper by Sensormatic to a activate not the foot loading etc. your technology discs Sewing selected twin specific metering/thread be thread Settings in project needle twin feature start to to support active your Just turning type, removed Help and stitch you creative off. thread. meter thread Settings will needle choose stitch. the needle a a Settings, swipe to Settings the settings; metering accessories continuously The menu. keep feature new twin Dynamic stitch Center keep twin will is and prevent use Free-Motion feature the thread your ActivStitch™ selected tension. the When default the icon™ as will session this between be needle setting thread needle settings. the correct and it Straight is Embroidery or best will machine saved, damage or cannot be tension, setting metering. selected correct in Spring using start whether or machine. The or settings thread setting reset be way the tension. or will the not reset Foot even of be to off, to at a in 2. 1. Temporary Default Settings Settings in white in orange colored colored check check boxes boxes The Multi-Touch Screen 63 cuts, the size. design selected 6A, material thread any The design of automatic no Foot of the improved sizes. trim. of loading for weights options: hoop stitch when cut oidery Free-Motion combination adjusted jump a different hoop independent Size be Embr available thread and of threads. using can area, cut three default list Hoop Sensormatic automatic a Height Options when the ult the height and thread oot be open F Cut between embroidery foot Defa cut to d using embroidery will esser the to Touch hoop Select When Pr Choose presser performance Threa thread and/or automatic The Multi-Touch Screen the the Customize Backgro slider light Adjust LED until shown whenever When Lock until attention When Audio left, volume sounds Change Audio will Select Language All Machine even 64 settings left background the be conditions W you the when Scr to your selected, active, on the Repeat V changed ork to in volume is the olume the pop-up und pop-up touch een make your changed. the it brightness your turning desired Light made audio Settings right is the screen Image inactive machine the OK them is in image after creative is signal messages to in Brightness volume muted. your closed. screen your language. in When make the and restart. less of the options. for for sewing machine the will machine icon™ the bright. pop-up. is the using ten the some will LED automatically screen be All LED seconds. slider room. be affected machine the warning lights settings texts off. repeated lights will slider is Simply all in A to remain when brighter your by pop-up the will adapt alerts bar. locked in selecting way move be intervals the machine All locked or to saved, is or to audio the the the to The Multi-Touch Screen 65 be the on to access also services. in machine the account machine and machine WiFi files. will to available. the your in machine Internet machine and be logged You in cloud. in In number, sign mySewnet™ networks with files have user. mySewnet™ can always the a account technical serial the you of saved you will connection firmware. user ™ mySewnet network With all available and activate/deactivate services. a the your for change contains to WiFi clear machine can user. update all access current Settings or, the as: with can Settings to you new search and connected a you such Information cloud, cloud mySewnet™ is able chapter. about connected firmware information be If settings create Settings WiFi mySewnet™ WiFi address more about machine, to synchronize will latest the WiFi the information information MAC Machine Machine will Read able you Read your the When ™ mySewnet in In mySewnet™ mySewnet™ In connect. WiFi The Multi-Touch Screen area. up area icon 3. 2. 1. Duplicate, depending The you area embroidery indicating Touch Quick Help Started Here Touch Help the The T The Smart 66 op will Main Quick Help Help options Top Smart want. becomes on to Touch you Center Bar the the Center open appear and the Help Bar Center Center, Menu will Help T question Help that Toolbox Delete, on screen Techniques oolbox OK area. included chapter. shows the highlighted find where Quick giving Center to Smart Quick Touch Mirroring you close the is mark which they available Help in you built-in want Toolbox icon Help and the the & icon in are mode a hold is pop–up Smart to short Tutorials. information green and and active. used. to User’s enter in and anywhere you open Edit. Main the text Toolbox and For select and the Touch are Guide, sewing about Quick Read flashes Menu. example; Help exit in. about. the in differ an It more the Getting Quick your Help. and Center. option includes icon A icon in pop- work or The Help. the or an The Multi-Touch Screen 67 Features Information Active 4. 5. cloud Strength Signal WiFi mySewnet™ Recommendations 1. 2. 3. to your Guide chapter font selected designs, Selection the about the swiping Stitch, connected the files, User’s collapsed in by saved tabs; be open show Select chapter. files device Temporary to the Area design can your to Built-in in of stitch/design, text open information USB the saved icon arrow. a Area open to one the to made Manager to you your to the tab your or for organizing tab File Information refer select Font. ea gives Touch the Store and Menu features Ar will and information folder, again. in Information touching entire Area Select files. the by Manager the or the Manager. Guide. Helps Menu Area fonts cloud loading in Menu File Selection activated information. File stitch hide Touch and machine. Menu the the Main or Design User’s Quick and recommendations about menu can and Manager expanded Information left. more the your the stitch Settings. Each and You Information The WiFi, Information in Touch File for Menu Touch Select to Selection Read Main Touch files mySewnet™ stitches Some The Multi-Touch Screen area Note: hide collapsed Recommendations shows If flashing The there When mySewnet™ bobbin regarding shows Recommendations Recommendations does Area. tab, After mySewnet™ WiFi Read chapter. enter network network Touch Read strength If 68 your you or again. synchronization the not Touch is more the about connecting Sign do signed the if recommendations touch machine case, in dot entire see you is from synchronize, password. not by the presser WiFi in password about the WiFi account. in Troubleshooting. and/or touching mySewnet™ need to get in mySewnet™ the information the Information icon mySewnet™ you can any to in mySewnet™ list foot, to Information Menu are WiFi, your not will if to status change signal protected, of see the stabilizer only access IDT available connect see machine cloud for can touch troubleshooting. arrow. cloud. icon will area ™system, available or account how the the be the cloud have to Area. icon be the you by should both to bobbin selected show It WiFi networks. much in shown mySewnet™ swiping is mySewnet™ a in in will or the in also expanded low stitch the the the Settings. create be Sewing available case. WiFi be stitch information signal with possible mySewnet™ Information used. prompted to plate, If The chapter. a your the a cloud new Mode. Settings Select and It green space left. also to or a to It 4. 3. 2. 1. Installed Waiting Firmware WiFi WiFi Indicates Signal To WiFi Update Be Strength Status 7. 6. 5. mySewnet™ Status Indicates Available Firmware mySewnet™ Update cloud The Multi-Touch Screen 69 to in. the also be you is in top the the the It Touch can swiping. in Tie-Off on mode collapsed by made panel hide as stitch/design. currently Information Information Menu arrow. to and placed. are Area stitches the which have the such around the be of colored on to you selected you show show it Features possible the to for to moved expanded menu. features, on mode a touching be also number be want swiping. icon icon Information is changes Active by depending can hold setting by can It you or open which & The to entire activated area on Panel es speed Menu differs down the arrow. where stitch/total touch Information information collapsed panel the the shows anel Settings. the the hide Menu Panel and the eatur panel P needle F to in Simply depending selected The shows information the Touch Touch again. again. section Menu Information in. touching icon also an Note: are Menu The This Options, Area move Active Shows Area Temporary possible screen. Information The by entire expanded design It Note: The Multi-Touch Screen and expand Swipe Some Options window. 70 drag menus to the browse the Selected window colored contain categories to more triangle, a Fr size om than in of in the the your is the window initially lower Menu choice displayed. corner and/or by P touch anel of the The Multi-Touch Screen 71 the in highlighted be will mode screen. Creator the of Appliqué Detach Move bottom the 1. 2. very Creator the off. to in mode Drag on the the Shape active up. will or hold placed functions Toolbar machine which Toolbar. desire the & which on/off. it. Tie-Off are on the the pop’s you your and Reset Creator e.g. Features. machine open as Mode. show mode Touch reset to access to control ea To select to Your windows them turning Active Ar depending icon the screen icons Edit Stitch-Out function, Appliqué around. and you highlighted a full the when ork screen Embroidery control. until be e.g. under differ Mode location. of W Detach in arranging full the allows moved will will Toolbox View one the by center be our activated shown between changes entering Embroidery Sewing Embroidery Y open close desired the be created can icon™ in in in to Smart most to een Touch Touch in Toolbar is have your Toolbar x that it toggle when will Bar Bar Bar that Bar the use in. the the to you Scr icon Bar in use are drop creative lower design screen. Base Base Base a ull oolbar remember Touch default, and you The the controls Move 3. Functions 2. 1. If Base Base Touch F Customize The icon T you When function The Multi-Touch Screen 72 WiFi & mySewnet™ Services (. of the 73 file the with in the the the and the your copy restart get will cloud where at features: to on find on your number your not update installed. is Connect version to button mySewnet™ formats, be fonts firmware to will Unzip accessible thumbnail number do on machine during you for handle screen. off. the download and file as or USB This firmware folder new file. and device. machine. to located device. to machine unique. a the portal your e file computer and following firmware Reverse times the the folder in software zip new unlimited the allows version mySewnet™ machine the on a USB on not ar turned machine. the to USB old cloud the the Information. available verified designs a an the is off is the your of TrueType™ the the button, tool machine. is no the automatically computer. to be Explorer model with turn files several in signed copying www.pfaff.com embroidery your is more. Using adds on updates. shown turn name with at from name most firmware create will sync It on your will Check firmware Softw mySewnet™ is and your Release (.clo) viewing and drop Machine completed to not there file when the machine when Reverse restart on package folder the the is files content file mySewnet™ find from machine port icon machine completed Do Windows cloud The different and loaded that the to the stick update Information. website website is available update the switch. the the may and fonts change machine. USB Update your your machine, designs: fonts Check the sure that Settings, to your a program existing update hold Drag machine (.clo). USB any login and e update software sewing not commands device in copy the to process. an reading for automatically. file the update the update. ar sure an and Do Make Machine of Select PFAFF® PFAFF® find also icon™ your firmware machine on trim and USB ON/OFF your mySewnet™ into the the the can will Download file Note: file Note: clo) update The Make the version Press front the when The restart number update When images, computer transferred from account. QuickFont OpenType™ embroidery add synchronize computer. embroidery Plug-in and The computer support. • Visit • www.pfaff.com you firmware 1. • You Complimentary A creative Firmw Device Visit 4. 2. 3. 5. When automatically. Settings, a a if that able a The to pop- see newer be the can be open a connect strength machine be Network. WiFi networks. activate of with you to visible is to to will sewing will you in to which will signal your wireless signal firmware. icon you Firmware Only icon there need protected, Services benefit shown WiFi the Hidden Area you pop-up information WiFi, where machine. available recommended the a low WiFi Area. installed. be later that the you later. reminding latest a see an of to the with be updateable it to machine update your in will the available list to connected, screen also Touch be have always in open features Area, password network. an protected, your the is WiFi the or to Using is downloaded. can detected connect Information firmware firmware available. It area. network ready install for When modern, Information on to be a firmware padlock. a has always download the icon the from firmware You password to hidden to signal is machine With and the to in firmware latest connect the WiFi. will network the update in search password the new to shown ™ mySewnet Information any the closed machine. install is services. icon firmware Update of the Network a latest dot be machine the icon™ icon™ network waiting to the & get information chosen get network. if connect using enter oduction product. e a of in the to the Network to Started WiFi Information download updates will latest with available, ar not the the name the firmware possible and also If to have Intr network dot in it Hidden the the choose do the flashing able Select the creative creative and can WiFi install automatically embroidery network ™ mySewnet Troubleshooting. New Firmware you about be a connect. pop-up you your you 2. Your and you yellow about 1. Firmw Hidden Touch Firmware to will Update. visible If WiFi. If user firmware pop-up installation Touch To Getting WiFi Your 6 prompted to Touch strength indicated Settings. If see A green You makes up enter the WiFi & mySewnet™ Services at software. 74 the mySewnet™ You can portal. also find the complimentary software are More available information on the and download detailed page. installation instructions WiFi & mySewnet™ Services 75 edit the current the the in From view machines, different to files through with portal. able register be as status manage will website and such A – you ™ mySewnet the profile embroidery portal services cloud cloud. app. and user and machine SewNotice ™ mySewnet ™ mySewnet computer ™ mySewnet personal mySewnet™ • a to or the you the on the in you able – green account a settings. offers your on from three your a browser. cloud be of files where on and your folder your your on to cloud. where the files icon™ the computer ™ mySewnet from web through cloud with as folder on account. tool in users tool computer store the find cloud cloud. service files create hosting your services. tool login-based such mySewnet™ and account files sync opened cloud shown you creative sync mySewnet™ created on will for personal your can in ordinary be the to be sync mySewnet™ based be area. the or on portal. features an you mySewnet™ cloud You personal mySewnet™ cloud will the owners on where folder following: personal machine access will also service tool icon Troubleshooting. mySewnet™ mySewnet™ cloud to The cloud A a ™ mySewnet all the new connect – mySewnet™ Manage your and mySewnet™ A can is local to see the the a a – machine folder folder through sync – pfaff.mysewnet.com. status a files Manager pop-up services. the Services at information a featured mySewnet™ mySewnet™ with cloud access Cloud Account cannot File mySewnet™ machine. different keep your contains cloud cloud cloud cloud portal account cloud the places: manage account the and icon™ register mySewnet™ In the mySewnet™ to available in the cloud portal and to the places: – in to is registering and the synchronize, icon™ dot which from mySewnet™ machine way save sign that different creative access with not synchronization mySewnet™ choose the machine, mySewnet™ machine mySewnet™ synchronize mySewnet™ mySewnet™ synchronized mySewnet™ Install computer to will different ™ mySewnet ™ mySewnet machine, mySewnet™ your simple creative three the cloud mySewnet™ computer • The If does The mySewnet™ • flashing use Touch can mySewnet™ • mySewnet™ Start ™ mySewnet Your account A services • • WiFi & mySewnet™ Services time Note: free completely synchronization Install T Installation machine. space, machine and The Used 3. 2. 1. the settings. Touch 76 ool sync Once install. wizard. mySewnetCloudSyncSetup.exe On from Download delete machine. the computer content mySewnet™ space. other you The for it the mySewnet™ your mySewnet™ Space sign will folder When the will it mySewnet™ content files mySewnet™ Computer is full. stored Go computer, mySewnet™ in not installed, alert in the from on through only on of Delete order cloud of in remind in your your synchronization in you mySewnet™ on a cloud mySewnet™ your a your local mySewnet™ cloud small the to cloud will once. mySewnet™ you or double hard the you add, portal machine. folder move mySewnet™ topbar folder store space will steps amount If drive. sync again, modify you click at see files on gets designs, on or in cloud. pfaff.mysewnet.com. tool tool continue to Add, your account cloud a until the go your on of Cloud to activated mySewnet™ or run folder to to space the a to setup delete creative USB modify support the computer mySewnet™ fonts, the your file from Sync to space on is wizard setup the device content fill left, computer stitches your the or first icon™ cloud the is with your to to in Not Synchronizing Signed sync cloud.. cloud Cannot the mySewnet™ signed tool. sync in synchronize to tool. in mySewnet™ to files cloud. Check the with mySewnet™ with the cloud. the the used mySewnet™ mySewnet™ space cloud in WiFi & mySewnet™ Services 77 the with in cloud cloud your interest folder profile, cloud ™ mySewnet manage mySewnet™ etc. personal to the the subscriptions, automatically that your details and are of mySewnet™ sure e-mail Possibility the files – account machine make The with Overview and cloud – Also files. icon™ information, tool. profile machine. My personal contact information mySewnet™ synchronized creative sync • • your on is the You to your account cloud etc. related with on Login computer. account. page mySewnet™ project from in finished synchronization your machines web ™ mySewnet manager pfaff.mysewnet.com ™ mySewnet information services. has on also the to at sewing file the your available in as file in and mySewnet™ of into personal portal guide, now long a running your your is accessories file signed is as folder mySewnet™ and that services: machine the are user’s computer. and with Overview File as cloud – portal Portal shown you a optional drop mySewnet™ your means is icon™ different portal installed such on that the following and is the icon icon onize machines to the sure tool The The progressing. synchronizing mySewnet™ Drag folder portal. creative mySewnet™ access My material inspiration, use to • can mySewnet™ mySewnet™ The access 3. 2. 1. Make Synchr sync WiFi & mySewnet™ Services The The T With SewNotice can to when creative • The pfaff.mysewnet.com. • • The mySewnet™ The The The 78 r your All change Machine Current oubleshooting also app WiFi machine machine machine the Machine Machine it color mobile needs download icon™ will SewNotice and network stitch pop-up blocks display cloud attention. cannot has will bobbin device machine number App Cannot Cannot no not in the is messages app current loaded Internet synchronize password at thread connect app Download App can in and Connectivity via your Synchr Connect send design(s). embroidery low. Store such current connection to the protected mobile a messages files mySewnet™ as WiFi or the thread color Google onize with SewNotice device network to status: block a to the color Play. with WiFi you portal your app You the Network at mySewnet™ the and Make Internet. Make Make closer WiFi Make Settings. the Make machine account. Make Make temporarily have If mySewnet™ Make the password, WiFi entered checked network. mySewnet™ sure sure sure sure sure sure sure sure to New the or icon that that you that that that that that at cloud. be the WiFi in cloud the pfaff.mysewnet.com mySewnet™ contact If unavailable. have you your the WiFi you you there correct the there WiFi router. cloud machine have have have Information WiFi selected is is the is enabled connection, available password. is no selected signed a administrator router not accounts working signal, Please detects your accessible on in Area space has your If your WiFi try to move the a are WiFi you access signal your to again server on WiFi registered machine. network. of open although do the connection. the your mySewnet™ to from not later. network machine could the WiFi know network. your Touch in you the Sewing 79 to Creator headings. Area Sequence field. and stitch Information the feature in size expandable Creator™ actual the in Stitch under Use shown is shown them. stitch are sew and selected Features The adjust Active and stitches, oduction sequences. select and Intr – can Overview Information – you stitches Mode own Mode Mode your Sewing Sewing Sewing Recommendations, Sewing In 7 create Sewing 4. 3. 2. 1. 80 Sewing WiFi mySewnet™ Help Signal Center Recommendations Strength cloud 8. 7. 6. 5. Stitch Stitch Active Information Edit Repeat Features Sewing 81 folder cloud Help Panel Menu Stitch Tapering ™ mySewnet Load Menu Quick Main 16. 17. 18. 19. 20. 21. feature Options View Creator Adjustments Options Creator™ Screen Settings Stitch Sequence Balance Full Tie-Off Free-Motion 10. 11. 12. 9. 14. 13. 15. Sewing Available Touch Load can straight Touch Getting want & Panel drag and to the also Stitch select stitches. 82 hold see Selection set then possible the it stitch can Menu more Load Start a a on to stitch Touch triangle different touch Stitch be be stitch the categories. window Sewing Started Stitch in placed. moved Menu to is colored the a a enter categories loaded stitch in subcategory stitch Fr and Menu tab. the to around can om Main panel enter to select Select lower by to with be Panel load the are be default. Menu expanded the on top the a the corner. to listed it category Menu to the Sewing Sewing to to view desired default to load move Sewing If screen, load horizontally, you The the if a Mode. P by you new stitch. it stitch. a prefer, entire available anel simply stitch where Mode. touching touch stitch. A Touch Menu you from swipe you The touch and It it is Sewing 83 it the the to swipe on in Mode. preview tab tab. Menu stitch Sewing hold touching the mySewnet™ to subcategory. the available in Menu by of and Sewing accessible the your Manager in horizontally, in also directly selected File arrows is Selection Touch it view category Manager preview Selection stitch the listed to the the a a saved the in load folder the are File see Use device. to have select Select to om selected cloud open USB Fr stitches you stitch and to preview. a from a subcategory it. stitch open the categories a on a the that on to description. or Menu Menu load categories. Stitch stitch Stitch to mySewnet™ touch hold a Touch a between Main & LOAD Main stitch stitches without more folder Panel. file The a then see step Mode Load Touch to and stitches. with to Touch access Available Touch cloud stitch Note: Menu Touch Select Sewing Sewing stabilizers. Help We you stitch. when Stitch Presser The current recommendations Your Recommendations 84 recommend following move Center machine a Needle The foot, Free-Motion setting. your Straight Recommendations for IDT™ Plate recommendations automatically straight detailed that depending are Stitch recommendation system Option you shown stitch information use Bobbin and is gives The on to in selected Stabilizer. the the the can Case Stabilizer you left. Information selected will be about will with shown: be The be Guide the a shown stitch shown straight Straight different Area. in and the if 5. 4. 3. 2. 1. Straight Straight Stabilizer IDT™ Presser Recommendation Foot Stitch Stitch Recommendation Recommendation Bobbin Needle Case Plate Sewing 85 boxes boxes check check colored colored orange in white in Settings Settings Tension Metering Temporary Default Thread Thread 2. 1. 1. 2. in to , Help not under in the way off. thread or The whether using turning in correct selected Settings tension or best is and accessories correct the settings. selected shown Temporary project the When When or selected machine in the tension. feature Temporary are and Default is keep stitch new feature in continuously metering settings. in Area. a setting your stitch. choose made will meter of thread. session. stitch thread and your this active made to feature Settings Mode to made thread techniques metering/thread start discs metering. technology the turning by upper selected keep technology Settings sewing default. the on selected change – Information switch the the changes at to thread you Settings to thread thickness when echnology to specialty new tension automatically – on the all T technology for thread, Temporary your a Sewing automatically in that reset reset the in of on ways off, will even Settings fabric in using be be ActivStitch™ depending support upper settings settings. adjusting thread tension Settings ActivStitch™ the two start made the will will based of of metering not for the saved, or tension, Features when the are machine machine do change be ActivStitch™ recommend Temporary Default control Settings Center will the 2. Settings thread we temporary temporary Changes Deselect 1. will your Active amount amount except that There When your control Thread measures tension, ActivStitch™ Settings Sewing cutter bobbin presser Fr attached • following When Automatic • • When Automatic Note: If • position. even When Note: the Temporary if fabric sewing three mode All Free-Motion 86 you deselected, ee-Motion At After presser When eyelets. After position. stitches Information if Deselect Make different cut knife must to touch selected, selected, deselected, cover, the the foot in a sewing create stopping commands situations: thread the foot located machine sure Feed on Settings be in to Free-Motion Options no when two Thr Pr your moved prevent the Free-Motion will fantastic that the the Area. a automatic Dogs Options cut esser under holes single the following with using ead threads machine automatically the stops machine are the in are presser manually. damage will in IDT™ stitches the the shown effects. stitch presser optional Cutter accessible the icon F with lower oot needle thread are needle Options. automatically needle situations: can foot to system in e.g. the cut under and You the Lift foot accessories Sewing be automatically plate. raise will cut a needle automatically in plate automatic both sewn sequences. monogram can is For will down Active will stay disengaged. to just select in Mode. all be pivot in in be raises that lowered, Settings position free-motion above free-motion raised down features thread performed. between are height. and Your or the in the to the and the the in lift Free-Motion Options Sewing 87 Safety Needle Width Twin Stitch to to a the and a the the is sure sure size to you with they allow stitch needle is in in Mode presser when the stitch as the Straight width and width centered select select not the make make safety to used a safety Stitch or or the and breaking do project project needle be safety select removed Sewing session. stitch of Stitch centered needle, according is a width allow or that disabled In Always Always or new new width machine when twin the selected, setting setting the damage width a a risk Straight be foot. a width is cannot of of to the safety. only Plate this this stitch it limited the plate. the stitch safety project. project to will that session. session. stitch size as as start start supports stitch will are selected prevent selected, presser keep width new new the width. accessories the the to be damage sizes a a is Needle When width needle requires requires to show long only at at sewing sewing needle it. Select minimize attached as limit with stitch size stitch size Options disabled stitches stitch that that and will is machine that stitch new new Stitch to reset reset needle be will twin a a all option starting starting prevent to is is plate. a the with foot attached. or or of Safety to Plate entire deselect needle the needle sewing is will straight twin This after after needle to accessory accessory automatically Features Straight the used deselected all setting setting accessory When needle e.g. Limiting twin or stitch twin presser Plate of Started Started given be be Width machine when any any again again safety a selected, the will twin Needle an position Needle The The needle. and be Active use the the win Note: twin Getting remove setting When selected. width stitch the needle, selected cannot straight foot using position safety Stitch will selected activated Note: setting When cannot Needle When Getting remove T Stitch Set of positioning. Stitch needle the Sewing Tie-Off Options Pr Needle example, depending automatically When for sewing. Select buttons automatically Note: auto Note: position. the touching with needle When on adjustment. pressure. In the Note: Information settings Touch Off let When program beginning These 88 most esser you the front all machine. End at the The The For Up options sewing. Auto Up touching fabric. Tie-Off the up. select cases, or are Select of and needle immediate thread the machine Feed the Specialty Options and start is Stop the and when F When for on shown is The oot selected Area. Thread when Needle Feed different machine. Dogs raises selected the you let the to Down of at F the down. cut higher free-motion close a eed Position Pr the you Down will Feed stitch raising Dogs do new Tie-Off, under techniques options Tie-Off at essur or Cut. Up/Down your end and always program not the Tie-Off functions; (recommended) This Dogs project lowers Dogs the and is are the of the Active need end machine selected will use icon, number e setting a lowered lower other presser will sewing. Feed stitch. from Options the the of may automatically a to button three Features Tie-Off a Tie-Off be adjust Tie-Off the Feed selected the Dogs stitch. your can stops require foot the It raised when Feed Help is options window. also on your Dogs, more to machine the will also at Beginning, button, with in extra Dogs the settings. Center. sewing the for an be be presser the machine be possible pressure front the reset open made all lift lowered found Your stops on to of For foot to Tie- by to on 1. Presser Needle Feed 2. Tie-Off Feed Dogs Stop Foot Dogs Options Position Pressure Lowered Up Sewing 89 set a the The a icon of in in out. on or is the stitch + + start the it (for adjusted, numbers. the right. the move limit for of location. and be and functions width Detach stitch to when desire Smart mm – the position. – around. shows shows the adjustments. – until white stitch 9 needle close stretched the can to the to in use you to stitch positions the be density Use the desired using window window. x zigzag using as than width needle center moved changes a to control control stitch the the access will Touch the shown it density less be to the default, the the them the changed needle shows length width but your stitch control control limit center same. the in to position. can 37 area. be Changing stitch drop you to Touch always the width the the of the Toolbar. move above above stitch stitch icon may a is that longer and control only lengthening stitch off. to where entire limit arranging the the If width. be Toolbar + open close allows the Reset with remember can the stitch. relation Move remain to to Drag by the Setting the also stitch number number will and in embroidery position mm. controls maximum a will stitch the up. machine will select Edit Edit a icon™ in above left most will The The decrease decrease and reset mm change stitch, stitches position stitch Edit selected stitch Default hold mm. has or or and in to Length Positioning Width the which the stitch). To your pop’s & Stitch Stitch in to length machine The stitches use stitch number creative maximum sewing control. entire control. certain show lengthening control. Toolbox Your turning control machine straight The Touch The position the positioning you to adjustments. stitch Increase Stitch The the possible the stitch decorative Changed Stitch On width If the satin Increase Stitch Note: the Stitch Touch adjusting Touch Sewing when Tip: distance density. Touch length buttonhole the distance When Button to You Sensormatic + Set Buttonhole Mirr The Stitch increase repeats. Note: Tip: lengthwise, Mirror To 90 to sew mirror the entire Decrease Use stitch increase can using Some oring sewing – of a buttonhole Side the Touch The to Density also the manual between between the Stitch stitch). a density stitches increase speciality in Smart stitch touch to number Buttonhole number the when entire sew the a Side. the Slit button, density buttonhole The a Sewing satin the Toolbox or control Mirror e.g. Repetition slit – sewing manual stitch. the To threads. or stitch of Length above individual density buttonholes length stitches mirror + stitch to density. you Foot. in End to Techniques get adjusts sequence a buttonhole, the the open can and buttonhole different by repeats. does to a in control control Touch stitch set using satin End. how a cannot the mm. shortcut not the sideways, density visual chapter. to stitches or - affect + to number shows read to be with repeat to stitch decrease decrease mirrored. for decrease effects about the (the the mirroring. that the sequence touch a of actual manual e.g. stitch make or how and the 1. 2. Mirror Mirror Side End to to End Side Sewing 91 tight loose tension too too Correct Tension Tension tension metering Thread Thread 1. 2. is the to sure for keep Some few are fabric is a tight. loose. the tension. and fabric. change to layers. threads. the thread selecting the will stitch. ways of in you bobbin feature make too too depending of the setting of will upper between thread. is is and Make thick correct of two and thread tension thread fabric when discs metering/thread possible. control side fabric the will of selected the feature stitch. piece with has it Mode tension two tension upper top the continuously the underside Metering metering. use balance thread. when thread default durability thread thread metering. technology stitch. of the metering metering tension metering metallic the the tension scrap meter to fabric the and the the the underside result loaded a ead feature affect and that thread on to on the Sewing thread. of on piece the on weight reset needle buttonholes the tension. using in technology thread denim only and metering check selected be on between value require used, sewing the on and and ensure visible scrap tension metering/thread bobbin visible is the heavy will when and the is a to thickness visible ActivStitch™ tension/thread is echnology of settings best tension/thread may technology thread: between thread appearance the T for changes ension/Thr tension/thread tension/thread visible automatically evenly on check use T sewing the metering thread the metering/thread stitches using settings the be to use fabric and tension thread settings and ActivStitch™ thread thread the stitch control tests ead Settings meet decrease thread get changing needle amount thread when thread thread balance different the When thread the use the when the To of going thread the Thr few metering e.g. best the stitch. techniques setting, should the the current the thread thread to a bobbin upper When changed with are the ActivStitch™ Increase results the decorative threads correct the the the For the For thread Make going If fabric, Reduce If fabric, Increase When amount the The control automatically Thread measures special Deselect tension. Temporary engaged. selected between on Use adjust thread, increase tests Your you upper Note: tension best Tip: another Adjust ActivStitch™ Sewing Sensormatic authorized Note: Activate Spring Dynamic Note: in window. Touch be Feed Free-Motion window All Fr needle and mode to To stitches. presser motion presser down Skipped while higher on will When e.g mode Activate Note: being Activate with to fabric Free-Motion. Free-Motion 92 the create hold moved the ee-Motion adjust stitches lower raise straight Dogs Optional Make The formed. sewing. Information thickness for for with sewing needle Free-Motion speed, plate presser is Do the mode, foot foot couching stitches where to to to fantastic Dynamic Your activated, optional presser and F the PFAFF® manually. with not sure will oot fabric set set set the on and height stitch. while Spring Options. mode The presser plate the lower spring free-motion use foot. open your the the the settings needle lower that you each and Fre the can foot on presser Dynamic Fr effects. a etc. Spring machine machine machine spring Activate Area. the since for will dealer. while spring the Options to machine the can fabric with will ee-Motion e-Motion feet the occur stitch foot automatically 6A For close as stitch F the IDT™ are reduce Free-Motion oot the select can needle raise you Foot or Touch foot each feet. the height all foot Dynamic at and Stitch if to shown needle Spring in in in the some be is your low free-motion can 6D stitch hold are system 6D if floats Spring Dynamic Sensormatic and between A purchased stitch being the eliminate Free-Motion plate Sensormatic Free-Motion spring in Width stitching. be speed is might Fr other fabric under lower the space Foot Sensormatic is recommended Spring sewn and over ee-Motion to is options formed. while Foot being fabric disengaged. hold Safety three damage foot the measures Spring sensormatic at moves the between Active with the the sewing in Free-Motion your free-motion Lowering Foot the presser Free-Motion formed. fabric will the free-motion Options on skipped window fabric different to in each stitch Foot the local up the open Settings. features fabric free- 6D for raise the the the must and stitch foot use At foot, is the a Dynamic Sensormatic Spring Free-Motion Foot 6D Free-Motion Foot 6A Sewing 93 button button Tie-Off Reverse on to lit. will Tie- The as to much. to an be the a to and — found too Your activate End. soon will and open many foot. or that possible to the as the twice + Tie-Off. machine lit. at raise. lamp height program reverse in how button, Beginning, also performed. be the the Tie-Off to presser in options window. is be reverse foot performing will Program button indicate do It stitch. will the in you to touching a Tie-Off sew. decide Tie-Off will Tie-Off indicator foot performed features height. chapter. three after and sewing lit of to for by selected lamp presser the perform options be under stitch. Reverse you be sewing foot a to stop the end icon, use Tie-Off the stitch Patchwork reverse want Active will lets of Repeat presser programmed, program will threads height freely the No is when functions; Tie-Off possible the indicator The Options you at end press also reduce and button the it Cut. you presser foot Tie-Off forward, under Tie-Off, Stitch it lamp move Cut to Repeat, the and close performed. cut Cut button finish button. action the stitch the not at Beginning still sew. be sewing. to allow machine. a needle Tie-Off makes different in Thread sewing area. Reverse to The presser Stitch shown will length, decrease Options of Thread and the will sewing to Repeat must indicator a The Thread immediate Reverse or the Reverse and of careful with are reverse select start End. Tie-Off Tie-Off Stitch touching options Repeat stitch about back Stop Be For the the change fabric End Tie-Off front you go The you Press action When machine automatically stitch. • • • Note: activate No Press Tie-Off To press Single Read repetitions exact Stitch Stitch let Touch beginning program When Off These Tie-Off increase Note: settings and The Sewing information the Note: Sewing corrected. When Balance Save controls. to Adjustment Touch Start technique, Read return touching Manager. To file file In between Touch new touch name create keyboard folder If touch fonts Previously file screen. the To 94 you match List cancel save Multi-Touch name type. to folder. by are about the & OK the a want sewing to to Balance the View In new your Stitch sewing hold showing open When shown. your In Sewing Close. folder and the mySewnet™ and the to List the saved Thumbnail organizing to window. confirm. each folder, file, save on Save a on touch sewn balance it, save and in you thumbnail the The with the Screen Name then Mode. special the designs, touch file the process, pop-up Thumbnail to stitch sew simply sample Save folder OK Base the is files Change name a Cloud may your View your shown folder, and the again, in fabrics keyboard pop-up on stitches, Bar in image you to the close touch Save need by your a saved a file folder a each open pop-up the to piece list pop-up View with touch using the can or using the button, open to of file will Create preview or file doing balance sequences stitches it and choose or be the the of pop-up icon as and & using the will close is to the adjusted. scrap to the hold touch thumbnail file. file shown located a New + a confirm. to save Balance appear keyboard USB on special to and will in the name and toggle window fabric. on save File and/or the OK. Folder, into - device. be with the you below in screen and on To your Then icons. the the will and the the by 5. 4. 3. 2. 1. Save File Selection Save cloud Save Name Current to to Folder USB mySewnet™ Area Device State Save button 9. 8. 7. 6. View List Create Close OK and New Thumbnail Folder Sewing 95 for and and feet and the select point end corner the fabric. button. stitch the to a width. stitch you point a tapering. of and if touch tapered stitch Off presser machine selection both When tapered satin stitch Tapering end beginning Reverse next when the for satin stabilized visible tapered selected tapering. your or taper the the without and in the stitches. the of desired, special the be stitch. for on it the the beginning end as visible not at both Select satin stitch beginning degrees tapers with for Touch piece touch the cise some used sew - be a on exercise long will 4 45 er the be selected beginning end. stitch will as on touching will start Off Ex sewn, angles Up/Down the is the regular can sew the stitch require by select menu a continue selected. of at satin will ams to stitch in is a to and taper be Stop been will with commands and stitch may satin automatically machine angle This view Stitch ogr end. has taper will 4.3.6 satin a with commands the an fabric select The satin Stitches tapering points Pr tapered Needle Stitch and will machine Try Tapering continue open the you stitch stitch be button. Tapering Satin any length and your sew. Select If techniques to tapered The The stitch. buttonhole. to continue the can then accessories. stitch Taper Tapering a the Select Open Activate When Turn aper apering stitch. Note: The remove end, desired e.g. and that area. corners The T and menu tapers. lettering. of 1. 2. beginning 3. start then 4. Reverse 5. satin T The Sewing These Sewing Activate Note: using millimeters The length. seam Program reverse desired possible repetitions exact the The taper Combining Combining Repeat repetitions The Single program The P Stitch Stitch will repetitions are of Once set until sewing. desired Toolbar To repeatedly. control. patchwork activated Program 96 atchwork repetitions program screen. the shown number seam Single Patchwork stop the The seam will you and the Repeat length and indicator length. stitch Adjust The and Repeat to tapering last Stitch automatically an is is Tapering instead. +/-. is automatically last have above Stitch repeat of of is seam length, activated. inactive. This Tapering select is now exact a reverse select of repetition shown makes a the using length of shown repetition stitch Pr repetitions When the stitch set Pro Program the is is programmed Program will the stitch Pr as Single stitch ogr The a is Patchwork very the it length shown tapered the length, stitch. included gr indicator The described it in ogr also and +/- above and you When increase the programmed am length possible ams the of you when +/-. useful length be of Stitch Single makes am and press lets Reverse Patchwork want the using in lets and working the repeated touch want the seam The you in millimeters you of stitch the the on Program. the you when stitch in Program. that estimated and the the for to Stitch +/-. it a the number start the estimated Tapering. repetitions to stitch, with decide Stitch possible sew. button light repetitions you Reverse decide can the is +/- area. sew. length Adjust with is quilting. machine Programs sewing finished. program the finished. Single to until be controls. Repeat Sew the Set how above of Touch length is The program the how sewn same for of button the pressed Sew repetitions length Patchwork the are the shown your again same your machine Stitch will many you This is many length makes on the Stitch number in your sewn. length. end now be while of to the an on +/- the the will the lit it Sewing 97 Foot Position 5M Start Foot Buttonhole Buttonhole Reverse 3. Repeat Presser 1. Buttonhole 2. Sensormatic the foot the lines feet lid. long the them button many of the the Manual As is the the threads the as below The can column. manually. by 5M. thread. threads pull it buttonhole. arrow over Buttonhole and the on ends presser use under You of the foot red Reverse and that repeat the copies. gimp gimp 5M. icon. hidden button. second ruler sewing so thread the the Sensormatic the Repeat ends is back special professional will want pull the buttonhole the buttonhole with Foot a button. Tie needle the presser Start that a The regular gimp a press the you button length identical buttonhole, and some the automatically thread center of use thread or have as sewn with sure foot. of the into Start/Stop slit of machine deselect sew the the again. your sewing are or and repeat the garment. the to long buttonhole, size the aligned, Buttonhole length require cotton just bartack make loop using on thread. as Pass a over can that the from the Buttonhole the threads are when icon button. the completed of bartack. the of foot. and may buttonhole, control adjust buttonhole pearl 5M. and durable adjusted You be a Buttonhole Manual than button excess the selected, echniques gimp function sews side wish. column until foot Use T marking visible is center cut. of Foot, Foot over will bartack. have sew the length second Manual the Reverse columns extending the the stable, manual Buttonhole your Buttonhole the a you the first buttonholes are larger the of completing on a Buttonhole slit icon the only the you the you techniques front wrong bar as thread ed is the accessories. cut machine more the with sew cancel that sew the the Place Snap After Thread To buttonhole icon When Repeat as To Sew Touch The When to When pressing threads slightly measure up buttonhole times Buttonhole Set Cord Corded are appearance. 1. Repeat metal Buttonhole to Manual 2. and 3. Sensormatic Buttonholes Sewing These gimp to and 4. buttonhole Sewing new the program Repetition To Use F that If aligned Mirroring Place lowered. button To Sew The sewing stitch without width appropriate subcategory 98 our needed, change sew desired starting the will direction the designs. On between Dir sewing. on mode. with Four having fasten for button icon increase a ection direction icon. a length for button, point 2, you. the Button Direction by When the to the The holes the to Start under swing touching make is turn is Four button or actual Feed Sewing remove touch marked sewn selecting with to decrease stitches the your of sure Direction sew. Dogs the button. on the one in one presser the the fabric with The one the needle Width a of will of the for presser stitch holes fabric, direction, the machine the If stitch an sewing number foot or automatically needed and four x icons. four for in in in holder. foot is using the category decorative the the stitches. loaded directions. on will of select change and button width stitch patches stitches the sew Use select to the be Stitch 9 When field. the the the is and are Sewing 99 top For to the sew on icon™ pairs double to fabric your of stitching the (approx. woven starting and Ribbon locate ⅛-⅜”) sewn how stitches your Stacking, are combined/ mm be creative on and using same consist for to support single Triple 2-5 second, the to your decorative when (approx. for ribbons Ribbon, Stacking and colors settings. stitches. Center in the sew. use as stitches like mm the your to fabric two designed sew you instructions of to Help Edge appropriate in look such correct Double as 2–10 Narrow are stitches sure for your echniques one use then the T Lace Stacking Be to that triple recommended and and get Single, stitches stitches elements and The stitches under first. you stabilizer, Projects are machine. For the decorations Technique Help stitch the stitches Stitches use Stitch Stitches your special weight, Radiant each. stitches. includes beautiful what first in ribbons Stitches other. Stitch stitches. Quick for the dimensional and the beautiful results, these automatically recommend each matching of Sew overlapping point preview stacked. Touch ⅛”-¼”) Stacking of Sew machine stitches into ribbon best Stacking Floating, with type stitching. We Ribbon and Add Ribbon Special Special Sewing 3. one 3. 2. 1. Sewn 2. 1. Sewn sew with ways connecting Floating Floating 100 Once foot. Once sew Attach place Place IDT™. Attach outside stabilizer Fold piece two the to with with using use the stitches Bi-Level pieces finished, finished, a two of the Let the stabilizer 1A the stitches the Stitches this fabric, folded underneath, pieces the 1A Bi-Level the foot: Bi-Level folded of technique; create Guide desired foot fabric folded pull pull right are fabric. of underneath. edge. and fabric, the the invisible. Guide a Guide together. Foot, sides special edge seam making The fabric fabric engage the right a Foot together, Foot: follow second first allowance. piece effect There over. flat. sure the and sides technique of the IDT™. technique where it are engage and stabilizer together, extends guide two place the Start is the different of to is and the the and to to sew Sewing 101 Icon Feet Optional a or in will the and foot and the sew using with presser the on stops. stitch to and extends the presser desired of fabric technique. the sewing foot presser be stabilizer lukewarm stitches you Attach machine the stabilizer. for to projects in your selected guide the engage special Start/Stop machine markings sewing on special presser stabilizer lace the the your the placed. and soluable soluble beading beautiful reached side allowing stitches the the the underneath Pfaff pen, on be Touch which require stabilizer touch of machine. until Foot to two follow have that stop water water Make edge. Start/Stop out want line. function. then in special the stops. sew stitches you sure and edge stitch marking find you stabilizer Guide Exclusive place and sewing soluable a fabric touch marking that to shape. and built as drawn the techniques Down an a until Edge Foot and candlewicking, the so Stitches and fabric Help you includes stitch. any area machine the as are water using making long 4–6 center folded garments. in want Stitches Bi-Level have line. Lace These eet from as the that fabric fabric time the Guide Needle fabric F on the Quick it the line, such Stitches folded step the Start/Stop you for a the the selection the Sew accessories. up stitches matches until backwards. next the drawn Edge foot. stitches stitches Touch stitches. subcategory beautiful of and Bi-Level IDT™. Fold underneath, outside Draw Attach Let foot. remove Dissolve water. where 2A Place foot. Activate sew Repeat length. Line sew Turn foot the Touch The stitch required the is This techniques edge feet Note: 2. Optional pocketlines 1. the 1. 3. 4. line Sew Lace These 2. 3. 7. 4. Radiant Radiant 6. 5. Sewing • • before The runs The When Bobbin Pop-up • Remove pop-up Check in When control sewing need message 102 the Sensormatic Sewing Sewing folder. Sensormatic Sewing Sensormatic machine out to pop-up. the the doing Upper and without replace message Thread Sensormatic or appears bobbin bobbin a a an breaks. do Messages buttonhole stitch any stops adjusted Thread not Buttonhole Buttonhole the Low replacing and Buttonhole giving of thread is that close automatically Re-thread bobbin. replaced the start Buttonhole buttonhole is following: that you the is not the sewing. running Foot. Foot If pop-up. can in Foot notice a with you the bobbin, buttonhole. in Sewing not if upper needs want a Foot saved the the that low, full be touch mySewnet™ upper sewn to one, you to thread, a without continue pop-up be the will touch with removed thread close foot soon the the cloud OK the Sewing 103 and not the twin and size manually. you on stitch it a Needle following needle when deselect moment the a thread appears the choose needle. Threader and and Wait Automatic OK you appears twin Check pop-up OK activated, threading. the Needle for is when touch this safety. sewing. touch message Press correct and enabled. Safety stop suitable is width needle, for appears again. to Automatic it not needle, stops pop-up Safety settings. Width the stitch need Check when twin regular button the stitch for a a Use message a in you Width Stitch OK Needle machine following the using using If Attention! When pop-up screen condition. Twin The choose Stitch suitable touch If needle Threader Cannot If Embroidery Edit design(s) You In Embr 8 104 Embroidery Embr can oidery edit are your shown oidery Edit design Edit you in the can combinations — embroidery Edit adjust, Intr combine, oduction area. without save having and delete the embroidery designs, stitches unit connected and fonts. to your machine. The loaded Embroidery Edit 105 Combination Design in Stitches of Strength Features Number Signal WiFi Total Active 3. 4. 5. Overview – Edit cloud Center oidery Help mySewnet™ 1. 2. Embr Embroidery Edit 16. 15. 14. 13. 12. 11. 10. 9. 8. 7. 6. 106 Stitch Sequence Appliqué Shape Embroidery Settings Edit Hoop Embroidery Scale Rotate Handles Options Creator™ Creator Handle Creator Creator Stitch-Out Area feature 27. 26. 25. 24. 23. 22. 21. 20. 19. 18. 17. Main Quick Menu Layers Color Load Load Load Load Stitch Full Screen Design Font Stitch from Menu Edit Edit Panel Help mySewnet™ View cloud folder Embroidery Edit 107 by it to like. the Menu. a select select of the design design cloud load design you be designs. Edit. stitch a in available the Menu more to step and and load to the the keyboard Touch changed Edit. to moved to on it vertically, on same center Design All and see more be where and be listed text Main oidering again to design the Menu Menu it the the about about mySewnet™cloud drag triangle see hold can want design listed are fonts can in of mySewnet™ & to directly the preview Embroidery Menu and touch are it place swipe size Manager. you Manager. the Area. bar within with tab. Embroidery Embr subcategory. Design Design categories. touching the Panel from colored touch placed File Available File and in preview. swipe and enter Main load embroidery in from the by the Touch in in categories be information information where to the to more Menu the tab. bottom the embroidery category window with Edit Menu Text. designs preview on designs fonts selected touch open open see design will design Simply a the arrows device device design in Information a move font it horizontally, to to to with design a design same in Menu vertically, a designs. see entire Menu also to saved saved selected, selected, a the without the Selection USB USB to is is the Edit, available screen. in select a a on listed top can The dragging selected load load swipe select Use listed more designs the select Edit Design Design Started Embroidering to Embroidery Embroidery created shown ont All the Design are can can F Design from from You Available to and Selection hold are see the be be also design design open design you within panel on it a a shown from & a Load once Load Start a a to corner. The If and and to about the You You can can be open. will Embroidery load design. design. Embroidery Note: folder Load When will Touch design information. between Load Text a hoop. placed. When size category Touch fonts. will Read Note: Touch horizontally, to touching lower around enter categories categories. folder a designs swipe Touch colored You Load Touch Getting Touch to Embroidery Edit stitch stitch It Touch selected stitches Use embroidery to subcategory Select are enter You placed. touch from in Load Load the be triangle changed Embroidery see within Touch Load file. Manager swipe stitch. 108 is see your moved listed more colored possible To the can File the designs, out and the a a to Available & Load the load Fr a mySewnet™ preview in category arrows in stitch also see by hold Selection stitches. and Manager. horizontally, Stitch in mySewnet™ om tapering around selected the same panel touching area the from Stitch Edit. to more to select load on stitches to lower view Another load in hoop. category stitch of the without by a top The mySewnet™ Touch the on categories. to a Menu subcategory. stitch the a programs Touch cloud touching previously file the embroidery corner. stitch open the and to preview Stitch cloud or categories stitch swipe by move available & to sequences screen. tab. the are dragging folder Main the Location by hold touching load The Menu folder with preview. listed to Available into All it touching cloud where Stitch to and stored see on Touch Menu, Simply it entire or area. step are available stitches. a Embroidery directly window in vertically, a on on more stitch that then folder Menu & listed stitch you the between patchwork, a the Menu holding Load select Main stitch touch you USB touch Menu categories. want description. colored Touch to stitches you horizontally, to and size have to Menu device the File Panel load categories swipe & Edit the a it can load on select Panel. can hold to a saved single the it stitch also to can to be be to to a on Embroidery Edit 109 is the in to the block in be block want all icon the color color color window identical want will the color. color you a design all color Touch it squares blocks select of all touch change. to same the you one in is that Block to new to open and Each to any the different color then to select Multi-Select than icon icon all block your window. block want the next changes shown colors. Color select more will icon, icon The square design. be list more Edit you or color To Equal color select view change list. color. make Edit on to One color will to Equal the your to the two to ones block selected the Color Multi-Select If in Select new to the in color icon Color a the pop-up. icon the icon the colors Select Multi-Select the palette Touch The color Than color. of in the the a All colors Edit e touch the Number select all select blocks of in thread Equal selected. selected. color new time. time. touch the of to selected can Number Mor image the Touch selected, Color Select corresponds part the the All Equal touch Edit Block Edit Select colors, one one Edit color edit design(s). then Select as are at at on the the you that blocks blocks can the time, lower Select Multi Select Color Design Color Color change change. a represented to shown blocks To Change is thumbnail where Touch Previously previous identical automatically You color the at change, color Color Touch selected 1. 2. 3. 4. 7. color Touch blocks 5. 6. Use blocks automatically Embroidery Edit the area and to To they By 2. 1. stitch-out Select be screen, To Select The Or Select Touch Layers Selected Color On-Screen color Touch which embroidery blocks All If Multi-Select When icon. the to by 110 you the all surrounded design change select default, der Indicates design Touch icon. list. designs designs drop and are of blocks left want you color Blocks to the that or the loaded color All All One Design(s)/Change indicated one open it of order in selection & selected to stitch-out touch are the at selected into to area blocks in in the designs icon the hold Display selected another design, another blocks select the the Layers not designs Design by to of thumbnail one layers on the so on a the loaded Layers embroidery selected with color in frames. selection you the designs. design, all on Select order, the simply are place design. the of embroidery window place window. will designs, screen your a can symbol Selected block highlighted design Menu different designs. All of in will touch You be in touch mark/unmark touch If screen frame a the stitched to to the icon area you are design be can where The simply to will deselect make list. & Stitch-Out list. area. the greyed numbered. the drag background and want it in again. hold will now selected be in activates Group/Ungroup the design and out you it green. touch changed. Non-Selected and be make on to easy and embroidery out in then surrounded can any combine the drop design the on show the in to Color the changes arrange color design. symbol drag the see the order Select the all will all in Select All Embroidery Edit 111 Multi-Select Group/Ungroup of to both all the the the design Group/ will the the the the want and of become the design on the touch touch A when designs; frame and and Touch surround select more again touch and, or window designs will design, Area time. deselect, once selected designs window. the two selection To one the will frame same Layers as selected ungroup, more touch is area. select Alternatively the Layers the design To they or to at in Embroidery A that the then selection and two adjusted surround disappear. you in select. the group. icon. and be to in screen oup will will design to pictures again embroidery the or design allows icon selected in want your designs. pictures the each icon the frame frame them on in again you have thumbnail designs oup/Ungr you Multi-Select Multi-Select screen selection designs thumbnail the designs designs selection If combine the individual Group/Ungroup surround grouped, Ungroup Gr Multi-Select Embroidery Edit 11. 10. 9. 8. 7. 6. 5. 4. 3. 2. Contr 1. Multi-Touch You Edit which The Control anywhere Touch 112 Full Stitch True Scale Hoop Edit Settings Zoom Zoom Zoom Edit Control can function the F ol Screen Wheel Window move, unctions Size Edit Options Slider to to in selected Wheel Wheel Hoop All the Screen View to rotate, it embroidery is fine design varies used using tune. scale for. in with your and appearance area. your fingers. pan Use directly finger the depending arrows to on position the in on the it 21. 20. 19. 18. 17. 16. 15. 14. 13. 12. Undo/Redo Control Move Rotate Duplicate/Multi Delete/Delete Mirror Mirror Move Resize into Side End Wheel Hoop to to End Side All Duplicate Control Wheel Embroidery Edit 113 Center to Move Move to to the and selected arrows finger for The the the your area. hoop use horizontal the with and position design(s). the of to icon hoop. design embroidery show icon center selected the the Move of the the in arrows the Center selected of a to from the center touch the move anywhere Move position in above it also design(s). distance the and the can selected Touch design(s) adjust numbers vertical position You Touch Move Embroidery Edit Scale Rotate in degrees selection handle Rotate on adjust You 114 degrees, the can the 90 the located clockwise. also frame degrees rotation selected the touch current in and the icon of The design(s) the move the center rotates rotation Rotate number selected your of by the icon the angle. finger above touching design(s). selected top and on of the use the the the arrows design(s) the Each design screen. rotate arrows touch shows, 90 to Rotate Scale Scale Rotate 90 unlocked locked Degrees Embroidery Edit 115 Size True the to the to and scale and use wheel. design size. and the a changing wheel arrows indicated frame icon 20%, of numbers decrease height. is the the control or width default one than The and scaling of This control use the without the selection of more Touch the to and 20% increase width When of scaling locked. touching design(s). +/- design icon center can design by are design a enabled. center the the screen. current you the Scale be of in the the selected individual the design(s) in decrease will on design(s) shows scale the or to of stitches. corners function, proportions padlock icon touch of activate finger the the selected padlock size arrows selected scale Size also increase in arrows and the the closed the the function. your the the To a can of the True number default Resize unlock height. Note: Touch adjust above By with use You move the With size the Scale handles Embroidery Edit Move Mirr Delete/Delete Duplicate/Multi Zoom Touch (s). and Select End To To outermost into Hoop design A from appear message If design deleted Touch OK Use magnification and embroidery embroidery Zoom 116 you red mirror mirror to the enter to the the oring frame to Duplicate touch confirm to the & the is is to from into Zoom hoop Options move to all embroidery hold placed selected, ask desired a a Delete left edge confirm. design design will area combination. will & the area. Hoop if on will to Slider to any hold you of show outside to zoom surround to embroidery the delete icon, number a the be make lengthwise, sideways, design The All fit on pop-up want and Duplicate area. shown Duplicate the hoop. all and out. the design selected the a move the Zoom to selected that of Touch copy Delete the the The message hoop delete above copies design(s) area. select embroidery will is selected select icon to percentage of to designs. outside OK area. icon the hoop. If your hoop all be the Mirror you to more will the in right loaded placed a open in slider. Select design(s) selected the want pop-up will Mirror the the appear. than Side area to of pop-up a hoop adjust at designs Move zoom to keypad one the if to End will add. design will Touch a Side. area the in Into to be Duplicate/Multi 1. 2. Delete/Delete Mirror 2. Mirror Move 3. 1. Zoom Zoom Zoom Into Side End to Slider to Hoop Hoop Duplicate to to All All End Side Embroidery Edit 117 Filltype Size Retain True 3. 4. Resize Undo/Redo Handles Resize Resize 1. 2. the to and your the To and when greyed stitch design use be in The the be using the the Resize Zoom outside frame design. forward latest will in latest width 20%, will through the adjusted hoop window. stitches activated step of design. icon touch change your than resizing, your They the of back to finger. arrows the selection not one remains. current in only Size less anywhere always redo Resize hoop, is step the embroidery undo When the to does your are size. to the undone. to True touch an the number use touch design design design density be increase Redo of repeatedly right left show the the the move the or open screen. the also can design area, function of original to possible. stitch design, of view the increase and the can wheel Touch repeatedly design the not or the Scale on of reduce icon increase a pointing pointing to the of You to are touched. or corners Rotate. The adjustments. original recalculates centered adjustments Touch finger size width embroidery design(s) placement reduce resize the arrow arrow Resize to the been all millimeters. above return your reduce in Wheel Adjustments the the the so adjustment. can in and the the the to you and/or your has To Not undo/redo function. machine loaded if pan return an change Move Touch handles move numbers height When enabled. Touch Adjust height Control proportionally. design Note: Scale count. Resize The through undo Note: out design adjustments. Touch adjustment. Touch Hoop. Resize Resize To the P To Undo/Redo Embroidery Edit Always Since Important Note: resizing. resized touch When Embr Retain Touch specific selected area enlarging Some deselect retaining your Retain were • • • 118 • • • to larger for It OK, It design Always and size If hoop Designs especially design Resize will design originally Stitches designs is does you fill OK. oider add you cancel Fill designs design Fill fill recommended embroider complex and your by Retain be areas the for or or enlarge The Type stitches is are is is not type default, T affected. Resize start can becomes resize reducing Y the smaller. always ype and fill saved, very to machine are our those satisfied is matter resize in Fill digitized created. return to gives be type. machine loaded with stitch designs. an digitized a detailed, Resized achieve to to a Type resized this design Information with and embroidery proportional. test The window the a distorted, Reload in the the a programs always to that smaller with design, will to then which and sample with design, lots Retain embroidery to best original It the the for larger too some you is Design be keep the resize of resized the single available will resizes result a best embroidery much, percentage able order the try cannot scale detail, specific design Fill of design you original of than the design If close results. your resizing stitches your to it Type you or in only again, instead you fill first edit you may embroider the be should most triple size to are design and resized types reduce design resized. when design, function select without may and selected want purchase for be When edit in made without and it your cases. of stitches, lost can the a not then as see window. size, resizing. resize better to functions again. position, design a they it. fill in or cause design be make is hoop. stitch If adds from it a distorted, reduced such to result. is before stitch the important change This irregularities. the After 30%, your to as design adjust other Please is cross more irregularities. embroidering it local and/or resizing, to a will design ensure adjustments. the to stitch larger than use authorized be consider it size, Touch 30% the make 25%. can less . the or embroidery position smaller smaller on become best than the sure the retailer. a project. True Retain possible following 20%. the and in by very design Size both In making software Scale Fill rotation. dense. this stitch icon length Type information is fits case, also each to quality. Some to or When return and resize you select recommended original designs, width. do you If about to very a a not larger original resized touch stitch If large want resize. the Embroidery Edit 119 a a the you will the color. the are loading by select Settings. fabric place list for PFAFF® to that in A open or the lines when to list desired of size colors embroidery grid hoop hoops Area size hoop select activate/deactivate Options. color combine the the activate/deactivate this authorized size. the hoop and and you and On/Off. default Hoop select your including the background change keypad. Embroidery between size design in when Grid can from touch the matches the Options Options the always specific a in hoop of on choices, select you hoops guide that different size, then distance a Hoop Hoop hold and the select size. as hoop color, area will purchase the & of hoop number can to ound open open Options a Options a set Selection grid between with hoop independent to to one Toolbox Touch You can use. the machine select Hoop embroidery will Touch Choose Backgr entering Use Touch Grid appear available designs. You grid. Note: Smart To Hoop Hoop In retailer. Touch correct Note: design, background grid. The Embroidery Edit default, drag Read Touch remember hold desire functions Your Note: Touch adjusting F Touch Stitch Touch 120 ull in and The creative about Scr on the Stitch Stitch to the use toggle default drop the selected you Edit x your center een adjusting Smart to Edit Edit sewing icon™ use close it changes between setting to to to of View the stitch. Toolbox desired close open the the and machine your most is control. icon when full always embroidery the the stitch and by location. until screen control control allows arranging turning select shown To in it reset Stitch view pop’s Your window. window you area. Reset in your the them white on/off. Edit. to machine up Touch Toolbar. machine Toolbar access and for numbers. as you & then the will to off. Full Screen View Embroidery Edit 121 and Angle Letter Font Confirm Close Fixed Delete OK, Load 9. 7. 8. 10. Area Shape Arrows Spacing Text Area Embroidery Text Select Select Keyboard Cursor 1. 2. 3. 4. 5. 6. by all and an The it add pop- be you Use all. to text to A Smart to area and all. the also and/or design, when delete font. adjust area menu. the where delete icon. want to entire to letter can OK text font to letter or move font delete the open the you the to You to the want want the new of to Delete Text. touch embroidery delete cursor in after area you the embroidery embroidery you the text size select want letters the and If the Touch If to an font text the in the position. select the you hold area. edit, text cursor in text. if icon. the & keyboard. move and a and select Embroidery the change in to touch cursor your shown the hold you by ext embroidery keyboard. into font is & touch T Edit Delete will the and place ask embroidery the the finger the write start at Toolbox text the above embroidery embroidery to arrows letter to on ext touch select in a T Letter the letter, your text, close The written, written area a a a another a Smart in is is and to change also oidery Letter hold Touch text add cursor keyboard appear inserted text text. & with a to the can can size be the the that that keyboard will create delete eate the the existing finished touch Toolbox To the cursor. touch want will in You touching font Delete To text Add Use to text deleted. up You open Use Cr Embr Embroidery Edit distance justified, Fixed evenly decreased will drag handles To the direction justified spacing Touch Select the shape Touch You T equal will left Select functions. the keep Decide have 122 ext change shape shape shape. justified, center place can your the the distance Shaping Letter line. Spacing Text the the spaced how your in the shape between current objects the your line. line the finger with Select Select the the the Touch Shape text to Angle text centered text text on size corners is text text between align your the placed will Spacing Text selected. angle. on will the each along a evenly of on will spacing shape the written the begin screen. the begin Shape or the of letter The follow parallel screen. all the letters right the shape, icon along shape line letters. loading slider, shape loading setting text icon The can design to justified. and when on the to touch line. with open be arrow to line: the If the except your affects shape to increased open to selection you adding If different baseline. the baseline options one the evenly you Evenly indicates text choose and for left. line all right. of choose letters will when objects the frame or select with Centered spaced, for or shaping spaced Select left The scale follow the to right to an and a on to 1. 2. Upright Curved Embroidery Edit 123 to are Into can to to is area Side. work the a End to if the deleted you OK design(s). about design(s). option Move at and your hoop from area. be options design differs area Side message in default. the of more Mirror the where Touch will to one Select hoop selected placed selected sewing the designs select read area. Mirror be the the pop-up than Toolbox the area. the outside Edit in keypad of appear. anywhere and and of Toolbar Examples select in the Design is will a embroidery design(s) work select loaded more in a hoop Smart grid will the copy hold If that a your designs. all Delete. used. idery open a Guide your copies the OK & the design on is Toolbox to hoop. of selected in available area. and it reset have is delete All The lengthwise, sideways, design make message the to to the User’s Touch Touch selected surround to to Smart outside Embro of any where the Hoop area. and number All the want want will Edit. Duplicate included area. area. oolbox design design customizing on delete Mirroring Toolbox pop-up edge T a a oolbar placed embroidery a open move to you you T hoop into about Duplicate open is On/Off if to if Delete, Delete Multi Duplicate to frame about desired oring the to the want. options Smart mirror mirror red Read Reset Select Select Read Duplicate, enter To from confirm. Embroidery Delete/Delete Select Grid Select depending End A selected, embroidery Move Mirr To Select embroidery area you The Multi Select design confirm Duplicate Select Smart The into outermost Hoop Embroidery Edit Smart Note: grid. Touch millimeter Reset depending The you area embroidery Select Reset Embroidery Select Read area. Select Delete You designs. Use Grid A Move The Smart Read placed hoop left near Tip: outermost into Hoop design hoop 124 red corner. If options Smart the want. the as can to area. edge Touch Touch about Toolbar, Toolbox you frame at to if to to On/Off to possible is open about Into grid hoop T you the set move open delete All open placed as oolbar Touch want Make T edge Toolbox or on & possible. top customizing the oolbox OK area. included Edit. will want as the inch area. and Hoop hold the where easily, Open Hoop any left to all a distance sure Move of in Embro outside Smart surround guide Touch place select User’s to loaded by on the the corner design The is that reset Help touch Options it the entering into available in hoop. pop-up a Toolbox is Grid on when design the design & between the the Embroidery your Guide of idery used. designs Hoop your that Center and hold the the design Smart hoop Embr On/Off. you and work message a drag hoop embroidery will e.g. is in and Examples Toolbar to and anywhere number Edit outside the and the area. from combine activate/deactivate read is Toolbox in your be the area, area. Area select placed oidery the grid sewing Move placed design about Select to the to design top as in to the of lines confirm. the default. in outside close area or embroidery the open differs left options Into hoop your will and at the Move place option to keypad. in corner Ar to the if the the Hoop. be a the the work area ea Into top are as Embroidery Edit 125 boxes boxes check check colored colored orange in white in Settings Settings Temporary Default 2. 1. a at off, or that of even reset on best is under or be reset setting the strongly foot, and start settings. active foot the deselected selected selected cutwork deselected. be based saved, machine will or a is is is we metering the be and shown be type. session or will accessories default to choose spring your floating e.g. selected are thread will foot Center Edit and list. new thread results feature feature feature The metering, settings; Settings the block for Area. a designs needs Settings off. set unless Help all setting upper turning block your color start Settings is when thread Settings in for settings: foot this feature oidery automatically you techniques color embroidery type technology technology technology When embroidery used Temporary with machine change felting Information used keep project in for the will be a Default Temporary to foot echnology best be when selected in embroidery the in in T Temporary special your Embr you foot will new in session. machine. For in Settings: the made the will embroidery a ways technology icon™ in block active that of made made Settings: indicates the and your ActivStitch™ ActivStitch™ ActivStitch™ embroidered two specific spring turning made as sewing embroidery control be start color tension metering tension. Features changes the the the are the default. block creative to some design Default the Settings when becomes restart new all to Temporary Settings 1. Active There Changes 2. and/or thread For cannot selected When ActivStitch™ thread color needle When thread the recommend select When ActivStitch™ your way Settings Embroidery Edit T Embr Note: the when used When Stitch When technology Note: threads. different can When will stitch. machine the embroidery Foot When g. do Some embroidery and Embroidering attached important or Select 126 win yarn a not correct machine. be the Sensormatic lower 6D with embroidering The It specific Needle either a embroidering using When the adjusted Needle support oidery couching is at Dynamic twin will embroidery weights embroidery very foot Dynamic the a that the session feature twin results. the a a needle lower start Plate or specialty important sensormatic foot with sensormatic the the for Dynamic change F Free-Motion Options and needle. of from Spring with oot of correct to use will needs improved theActivStitch™ the Spring material foot size a with foot. a felting. new the a of pivot T the foot techniques automatically to will twin ype is Foot the to start a Spring setting activate project setting. foot selected Foot foot twin to be be height and/or needle Dynamic performance 6D Foot, hold page. reset removed the is 6D needle Foot or is is the selected and/or presser to is to needed e.g. the selected the start above Make embroidery technology twin prevent selected Dynamic use 6D Spring ActivStitch™ fabric 6A. the of as sure Free-Motion thread needle the the accessories a foot when it for Straight It for new damage cannot at is you fabric. machine Foot the Spring good height the very each setting feature tension. using attach 6D, be to e. Dynamic Sensormatic Twin Spring Needle Free-Motion Foot Options 6D Free-Motion Foot 6A Embroidery Edit 127 Trim the the cut stitch a off block, cut the threads be or Stitch fabric. of are the visible, the the . starting threads are Thread and stitch turn Automatic be machine the in presser presser design thread finished. finished. be color the the will above Automatic that the manually. start and and is is the Jump of performed the cut trim the the mm, will will when any sequences. first lettering jump cut just Trim, the cut cut after to symbol 15 to software or thread and and at the e.g. stitch. cuts touch and threads stitch are are when automatic plate automatically Options: fabric this at performed than Stitch accessories plate. the can the be trim underside added and the Automatic jump embroidery embroidery jump upper Cut embroidery machine stitches to automatic thread with trimming cut a needle thread thread be Off. of together, the situations: You automatically Jump an an will needle – smaller and the for The change, stitch optional the your and to be time also the after of close stitches of in automatically automatically automatically cuts Thread Cut damage complimentary upper upper changes. changes. when when designs, marked automatic trim jump color will can letters, you automatically using Cutter Cutter cut cut cut automatic a in back the front pulled machine. It holes under underside and and the following three is is is placed be Automatic color color Options no thread cuts raises raises stitch like. prevent off Thread and the completed. through the when the two saves the at at after are embroider to Designs programmed trim. using will is and or on to off Thread Thread by in thread located automatic foot foot the you thread thread Cut to situations: embroider turn thread thread thread jump front stitch. in between Cut Cut cuts the raises raises manually. commands cover, selected, selected, selected, the designs you knife Select stepping function off ead upper pulled If If If button Bobbin foot presser jump Cut Upper Bobbin foot presser Upper Upper embroider Tip: sequences, threads Tip: Tip: turn manually. automatic Choose Thr Thread Thread whenever Note: Off When performed Cut attached bobbin cutter When Automatic performed • embroidery • • Automatic and This and to • • When after continues Thread following • Embroidery Edit select Touch will If you machine Once unit Save The from Touch Select threads. different adjusted When Pr the If the sequences to choose will Read name type. the keyboard To In between Touch into & a 128 new no you hold a list esser save folder keyboard folder USB selected choose select. appear the to default the In about you a and view want using folder, to to the be to on temporary your thumbnail new Design showing Def will device. for list. weights open open save and able have to with a List the and/or F each the on organizing to thumbnail oot improved a open hoop hoop folder. Touch always file, ault simply and folder floating touch save to and the Hoop a the the most selected pop-up Previously file stitch Height of touch touch the it, fonts size must file screen. hoop keyboard view Thumbnail Hoop to again material is OK to then suitable choose touch Options files a to foot shown has performance image out your open folder, the a are be the size. and in each the default name to In in been attached your the the Create Size Save shown. saved OK this mySewnet™ saved deselect. the it select and/or a and hoop file in of with list presser pop-up View and simply your to selected Embroidery the design(s). save no button hoop is touch or New designs, confirm. files for the a touch Name shown matter file. to when icon default embroidery as file pop-up touch your foot the file to size, thumbnail in OK. Folder, and your cloud with save. to OK File your embroidery using name with what stitches, height embroidery. toggle your Then hoop a & Edit, to you machine the pop-up Manager. To hold folder name file save file design and can touch can create size to icons. with on file or be 5. 4. 3. 2. 1. Save File Selection Save mySewnet™cloud Save Name Current to to a USB Area State device Save button 10. 9. 8. 7. 6. Move and Toggle Create Close OK Thumbnail Up New Between One Folder Level View List Embroidery Edit 129 ent Current Curr e chapter. State/Restore Current Stitch-Out State/Restor Save to ent how Embroidery Curr the about in State Save Read State Embroidery Edit maximum too The • • following This Embroidery Edit Pop-up • Exceeded • 130 There blocks. The One grouped stitches. can contains The many design pop-up have design design or are stitches. reasons: Maximum more of combination too too a Messages too message Combination approximately maximum combination combination many many designs many Your Number stitches. appears times. designs design have you of is approximately contains you in 500.000 are too been Your e.g. of in combination are Embr trying Complex Stitches the for grouped trying design too stitches. combination. one to many oidery make of to 500.000 combination and can the make color contains re- have a Embroidery Stitch-Out 131 and connected is unit embroidery the sure Make design(s). beautiful oduction your arm. Intr – embroider to Stitch-Out embroidery the to Stitch-Out Stitch-Out oidery attached is oidery Embroidery Embr hoop Embr Touch 9 the Embroidery Stitch-Out 2. 1. Embr 132 Sign Help oidery in Center to mySewnet™ Stitch-Out cloud – Overview 4. 3. Information WiFi signal strength Embroidery Stitch-Out 133 Block Combination Color Block Current in Embroidery Color for for Sort Merge list Stitches Circle Circle of Window Options Help Mode Panel Block Block Block block Menu Progress Expand Color Basting Ghost Color Color Monochrome Color Number Progress Menu Quick Main 21. 22. 23. 24. 25. 26. 27. 28. 29. 19. 20. 30. 31. 32. 6D is Hoop you hoop, feature best is in each very the height Before machine the Foot fabric. Stitch-Out is desire. plate at Your the the one for It Edit the foot accessories the hoop Free-Motion plate. the you 6A. fabric Spring the as needle Combination 6D ensure selected change not technology felting. Settings above the selected e.g. Stitch-Out. is automatically is set to presser and/or generally needle selected, is Embroidery will Foot is embroidery. and is 6D are is which the change Embroidery hold in Foot, 6D the Tension want Dynamic height in shown to foot Foot foot Plate Time and setting Edit Spring Embroidery the you Foot senses preferred Window techniques foot Settings in pivot Plate of Embroidery results If couching hoop plate review Edit Hoop everything a foot. ype Spring the theActivStitch™ Stitch-Out use your Needle T to correct best Spring yarn that Free-Motion Dynamic machine the needle View the Stitches for sensormatic with foot Progress Settings sensormatic entering Embroidery selected specialty oot Embroidery window. e.g. lower close. a Needle Stitch a the All Hoop Stitch-Out of attach F results. the Metering/Thread Positioning check to to embroider, the that Features Dynamic to to Slider the Position If Selected Embroidery embroidery will oidery icon™ to Stitch-by-Stitch to Dynamic Screen when use, in support OK to using When the either specific to lower Sensormatic the Straight currently Full Hoop Active Stitch-Out Estimated Step Thread Zoom Zoom Zoom Stitch-Out Return Precise Number not a Options. shown return attached. wish Selected Select creative will When The Attached The opened Attach recommended or important and stitch. Embr Embroidery Embroidering Some starting Settings attached embroidery 15. 16. 6. 14. 17. Touch do machine 5. 18. 7. 12. 8. 9. 10. 11. 13. Free-Motion, When Embroidery Stitch-Out Note: threads. different can Foot the embroidery 134 correct be 6D The adjusted at weights embroidery foot the session start or for change of from of improved material foot a new the the will start project setting. be and/or performance page. reset or to start Make embroidery Dynamic of sure a when new you Spring using attach Embroidery Stitch-Out 135 Sort Side — Options Options Options Cut Options Color Basting Hoop Thread Turnable Tension Metering Thread Thread 1. 2. to in the before can way thread both. Grand the List. the Sort, using designs Block correct selected, either secure for before color or or in or you in require Options best is all Hoop correct the settings. Block will Block Sort Color and the When three may made Hoop optional the option choose Merge setting Hoop well. and creative™ keep options that and the feature Dream continuously metering here Color as Color the can Side Sort of stitch. the choose which will embroider meter Block Sort thread. – in stitch the and certain if these options window. stitch results. Around here to to You any in Side Grand thread about shown set cut discs Block best Color by upper be using the selected Baste technology chosen want visible with recommended also selected basting more for Settings is options Monochrome. or the techniques be the a Color will Sort, Options thread thickness Options. you the echnology activated stabilizer. or when select can tension automatically on cut creative™ T for thread, your If is automatically Read add both the be only Options the Block on You the will Design to Tension special your fabric 360x350 set for hoop, Hoop Settings Edit. except List. Merge also embroidery will of Basting to or thread Stitch–Out upper Options thread tension Cut ActivStitch™ the can the Color based of of desired. can Options Metering metering the the the Hoop side tension, your the Thread if Basting Block Block Around about You machine fabric settings option ead turn of one urnable Embroidery Any change options: Color Color Note: Preset Monochrome. Merge thread Thread amount amount embroidery accessories use When your control Thread measures tension, Baste Select your Basting Read you closing Dream on This Embroidery T Color Basting Thr ActivStitch™ Embroidery Stitch-Out Basting All Color they the design Example: Color blocks. Swipe indication color color Robison-Anton design. by window The provides going Color shown Note: support You around Select will around Select Out. stabilizer. Basting 136 touching colors thread Basting be can will You When number. block Block Block to Baste Baste in in number placed To the the enables for select be the that Block the be support can 1:2 in It of go manufacturer, List activated in inside design, embroidered certain Around Around color embroidered. List. options is the Options the Color how RaRa opens also to the on especially The both will and Rayon you Basting another loaded block the first for many edge select List size 40 Block once fabrics outlining basting when color only are to the Design stretchy fabric. 2497, design list. 40 secure of of design(s) again set Options Basting Hoop stitches color the useful cannot List thread block weight each entering the Each When and in means options basting to the show to to hoop. fabrics. your the block, to add techniques. color order. when listed see be in basting the be weight icon. area thread, add are Stitch–Out the the the Embroidery embroidered a fabric hooped. color all to color block touch basting shown where a color the color Also add second Color of basting is and blocks number the to fabric complete block gives additional it blocks shows shown a Basting the in thread Block stitch in Settings color hooped thread will the stitch the Stitch- contains. that design an is of 2497. the the be are order List, your is Basting Options Embroidery Stitch-Out 137 Sort Merge Mode Block Block Ghost Monochrome Color Color area. the to stop so other. is Stitch- between designs not start each Color contains the remain each that All color, blocks the will you in stops will follow embroidery block monochrome design the same color before out. List the option will all the machine embroider in color your overlapping of Block to embroidery. the color sorts selected greyed the or eliminate deactivate be when to be visible and Color to to List. shades started To only same be disabled. the will Monochrome has close be the color of useful and have will Merge Sort Merge Block are monochrome be intelligently Sort will you grey with blocks different changes. blocks. ome a Mode can deselect in Block they Sort Color Block in if Once Mode option stitching appearance color Block Block color block activate the blocks Ghost Mode Color to Block in blocks Color The Sort the Settings. shown other color identical Note: same. Select Color embroider. Block that other Note: Select are for embroidery, Out Monochr Color Color currently All Ghost Touch Ghost especially color Embroidery Stitch-Out color Settings stitch Note: 138 blocks. If trim the the function automatic jump stitches is thread selected will cutter in still Temporary be and trimmed automatic Embroidery between jump the Embroidery Stitch-Out 139 shown combination combination block design design color complete current complete the the the of of of percentage Progress Progress Progress in 1. 2. 3. is or the the is the the next of for after to Color needle the block design current the by after whole in time oidery design the the minutes the ent combination color progress in in number current Window for and number Time the Remaining activated, number The Embr Curr is complete time current The stitches stitches embroidery hours in in the indicates icon. of of shows Progress embroidery the Circle, in icon. Stitch-by-Stitch. shown. of in in oidery ess is percentage block circle cursor Step shown a number number embroidery remaining the ogr Progress monochrome is cle Stitch-Out butterfly color progress and position position inner If Embr Stitches Stitches the Pr the total total and screen. the of the the the Cir of of The block. block Time icon. the the combination stitch stitch to to like the remaining circle open Block on ess color color shows next next to tools embroidering, Clock shows block. shows outer current current estimation ogr the current combination. The middle slash combination. Color current An Remaining color Combination shown shown slash Pr embroidery The Number Block to estimated The Number Stitch-Out Touch access Embroidery position When Embroidery Stitch-Out Center T P Curr hoop Use Hoop and hoop and When machine, also the a When the be hoop When in Note: space techniques. it Trim 140 rim bobbin, ark easier Embroidery placed Center park the start continue press position Normally to position, and with you you you Position Position ent Hoop different to position Position the once Position touch in select at trim have want need Position the a the Stitch embroidery. embroidering Edit will position Position to the embroidery touch threads the park finished to Start/Stop to return positions. when or embroidery move remove return of Center Sewing the position. the Position that options you and to the current your hoop. to the Position. the arm will button, after Mode. fabric need hoop the unit embroidery, current The hoop, to out allow current stitch you is to move towards for embroidery on in of have This e.g. have specialty park easy the stitch the position. the stitch when will a way. front position changed you, storage. remove free embroidery position also position changing arm sewing of making You show the when the Use will the can Current Center Trim Park Stitch Position Position Position Position Embroidery Stitch-Out 141 tension Thread Stitch to Go metering All Hoop to to Slider Thread Zoom Zoom Zoom 1. 2. 3. to will Use You slider last touch Zoom stitch- change thread a slider. the the through the the out. zoom number will open, the with screen to block, that upper after the the Settings. technology access will forward the move will Move zoom If in to ActivStitch™ above color to move to area. on step ensure Hoop the Settings. Stitch-Out the to stitches, left between Hoop. to will hold to keypad + to number. cursor & window A the design(s) embroidering few zoomed Embroidery screen. out, about a to and ActivStitch™ within the Zoom The block. the the balance embroidery stitch icon. Zoom machine have when runs the Touch all and in more echnology on Embroidery Embroidery the the the stitch or T Progress in the color and e.g. you in in not in rapidly. show Read hoop or backwards All backwards enter adjust whether secured. zoom large, breaks to much will to combination. current visible thread, more to feature be on can step stitches particular too Options Stitch-Out Move active whole thread. All a Stitch-by-Stitch to the is how Stitch-by-Stitch Stitch is will Zoom the – you thread to to right the in the to see bobbin control Step controls stitches go the The feature and depending the specialty technology the stitch where entered To Open Slider, to will Zoom embroidery show Zoom follow ActivStitch™ by-stitch. Go Step Touch upper thread the Embroidery Stitch-Out hoop your the you previously specific To It Touch Getting 8. 7. 6. 5. 4. 3. 2. 1. Use Pr 142 can move ecise Set Select Settings Zoom Zoom Zoom Zoom Precise Set Precise are design if also to Matching Cursor needed. locking satisfied your open a Slider to to to Started be Positioning embroidered Locking Positioning Positioning and Cursor Hoop All useful design Point the point, move with Point Precise Point when Center with in the touch the Window on to the design. placement. on Screen Positioning you place design Pr to hoop and Screen quickly ecise want a move without design to to the You window. Positioning find embroider your center on can selecting the an design also center of exact your a touch a until design location of to 15. 14. 13. 12. 11. 10. 9. exactly on your Control Set Full OK Cancel Move Rotate Cursor match View fabric Locked Design Wheel Point a without specific Point on Fabric re-hooping. on spot Fabric on your project or next to a Embroidery Stitch-Out 143 Screen Screen Fabric on Fabric on on on Point Point Point Design Locking Locked a Matching Rotate Move Set Select or the OK the a the in the the and pan with for on fabric to on on to the green design your fabric the place until with or touch your with the the exactly and to design. area Control the cursor. tune the arrows design, the point previously Touch is point is point on adjust Positioning. in hoop locked Cursor tune Move black a the like the fabric on the the using the to design, the Fine want to zoom position to to be in move in of the be of the or point. rotate Fine to Use needle point match een need to the locking 3. your you point. Precise will move on would and matching it to If of green Zoom embroidery the the cise match Scr design. needle also it Watch center step The arrows fabric and to you screen position to abric er close locking design. the or design. Screen Use on F want function the you cursor Touch from the the until locking to with Ex the want If tune. Wheel. position a another of the maximize on on pan on want exact abric your you stitched finger use placement design. Touch where on OK of F to touch black color Point corner you wheel. fine be in for or cursor. to and stitched the design a you design. select select on to to Point be Point your second continue The The in Control to to the where it position finger a the center Touch area to with that 1 3 2. 4. Cursor stitched ed where of change selected. Positioning. zoom the control screen screen, the with to the Locking Wheel point your stitched in want design, Design Positioning the a the rotate the point will match the Lock exactly previously design. screen It the in to satisfied to exactly Precise is Matching on number number number number you on shows Zoom cursor with position If of fabric/previously the around embroidery arrows locking previously Control your ecise Rotate Set Move Select to close exact maximize cursor matching arrows Touch design previously the needle fabric design or the Note: Touch design. ring move to angle your on the the the touch Touch green stitched where Touch Wheel, automatically finger 4. 3. 2. 1. Pr Embroidery Stitch-Out Point Find design the point Touch Set Zoom centered and When 144 design. pan Cursor the to Center using one field any to the center on of The Cursor the by embroidery Zoom of icon. the Point the touching of Set screen. Set the selected to Cursor Cursor Cursor design area each Point corners Points. by it so of will touching the the can or maximize Move cursor four be to used the corner the the position center to Set cursor the trace icons. Cursor zoom of is the Zoom to Cursor Embroidery Stitch-Out 145 will will the Then ent by pop- current are Stitch- In the a power state. machine stitches same a window later The time. that Curr is pop-up your Page. ongoing embroidery, few machine the a A a your e at current save restarted. there stitch. embroidery. Start pop-up your ensure Stitch-Out back turn is If Embroidery adjustments to icon™ State. current to State your the the and go to embroidery save Save at now a your from. save stop ready the stitch, control all approximately can settings. machine to creative to Current Current return State open Embroidery to embroidery one and to You design from in state, your your Save State/Restor want current continue the embroidering have the automatically are interrupted Current start you the choose can Start/Stop ent select when button up stop if position secured. current and only you confirm. was stitch-by-stitch can will to starting it be can you to Save can Restore touch step bring as Curr you stitch appear asking when will Save OK and you embroidering, saving want including the the Before You and will you threads using Note: embroidery position up pop-up Out Auto When continuously outage where work, current Save If position, touch off. When stored State appear Touch touching Note: Embroidery Stitch-Out attachment to The attached Embroidery to machine hoop embroidery disengage embroidery hoop If message When The Stitch-Out Pop-up Attach 146 the detect the hoop Embroidery that and hoop one the Hoop It while the will will hoop. it. is needs clear is embroidery displayed the hoop attached Slide very from foot. arm. selected Messages Edit calibrating. appear not IDT™ the or important to front the and embroider. You Arm the be machine to on hoop and and system embroidery select inserted will unit Needs to the the back displayed inform to also connector machine is screen the area remove in and You attached, to until properly be hoop unit Calibrate Embr you for attach must reminded or the it on does calibrating may into to to return clicks hoop, the a change a match slide for pop-up oidery not be suitable the screen, the damaged into to otherwise to match off hoop the the machine the place. the the hoop the Embroidery Stitch-Out 147 a the the an The to or back Touch touch you bobbin you from your go your thread pop-up that position. control has Position. pop-up gives thread. then empty the machine a pop-up, thread upper in change Re-start the stitch notice the and This the to low, thread the Center of needle embroidering. upper if of the the want position current secured. the Replace front closing bobbin. to advance message Stitch-by-Stitch running be until you the the the length is continue you embroidering. at hoop on will current opens. Step to pop-up when Without the Re-thread automatically excess the thread change giving the Low remain out. Touch embroider thread plan to button button, continue pop-up any Thread to stops move to to using to the breaks. run close one. to bobbin need appears back or Thread that Upper cancel OK full the position a out control soon pull machine stitches possible Start/Stop Start/Stop is foot Touch Touch the hoop with and Check will opportunity bobbin. It the runs The message completely beginning, When few ensure Bobbin embroidery. Embroidery Stitch-Out Cut shown any you design Stitch Note: stitches machine. will embroidery A Your tail thread Settings, After When Change 148 pop-up that changes and can stop. When Embroidery changing Trim tail it will in has and stitch Thread is the Remove The the Change pop-up message time function been Automatic stay thread is then you pop-up recommended the finished. the to cut. loaded will have stop the the same change will is thread, and is Finished be message. selected Thread Thread spool so be made. shown. in When sound embroidery cut you the Embroidery the of automatically Cutter thread in can Tail upper the thread Simply informs machine Temporary cut pop-up and color again, thread, the and remove you Stitch-Out Automatic will thread and number re-thread is Embroidery including that the closed sew the no machine your tail. thread cut a Jump is few and the the Embroidery Stitch-Out 149 cut will will the in be is using the needle Touch pop-up the to is a (820945- This in OK Felting felting require on needle threads special stitches a this Kit have without Check Wait the needle. message few needle see Touch a with out then machine resume. designs that require appears embroidery Needle cutwork will to Stitch-Out. approximately creative™ will back a your enabled. pop-up cutwork optional go you the stitched is marked ensure area from restarted. icon™ the with it this that be pop-up designs button to Cutwork is embroidering. are Cutwork Accessory) for also and this stitch require Embroidery when check cutwork skipped. to occurred, felting embroidery block can marked creative to interrupted. and be OK designs stops The machine and continue the has Start/Stop corresponding are and the color (Optional was (821068-096). designs accessories. ready the in stops Embroidery it return the designs the Stitch-by-Stitch should touch the Set Save felting to needles. cannot outage starting machine list correctly. designs designs and felting Step when and needle condition design Needle press and insert symbol you the machine position Smart the Cutwork block the and and Before and power creative™ pop-up cutwork secured. the a symbol needle shown, OK Cutwork collection. Note: the 096) Embroidery If When Attention! optional the manually color screen Cutwork message the moment size threaded If load Auto same using Tip: Change be Shape Creator form Shaping Shape 10 150 new Shape is shapes. Cr a unique eator Cr way – eator to Intr use oduction your beautiful built-in decorative stitches, sequences or even embroidery designs to Shape Creator 151 Points Handle Handles Rotate Scale Control 4. 5. 6. Overview – cloud Strength eator Cr Center Signal Help mySewnet™ WiFi 1. 2. 3. Shape Shape Creator 14. 13. 12. 11. 10. 9. 8. 7. 152 mySewnet™ Positioning Full OK Settings Edit Shape Control Screen Line Points View cloud folder 21. 20. 19. 18. 17. 16. 15. Main Quick Menu Load Load Load Load Shape Letter Design Stitch Menu Panel Help Shape Shape Creator 153 in it. your the Simply the your listed shapes. new available the where Letter load access onto eator lower a for a entire to to are enter baseline All Cr vertically, same shape the more screen. to move The load access load between the custom in the to design see Panel to shape the to to Combination letter Edit listed a to default. on your top along categories swipe the on are to categories. all Shape Menu Panel Menu within window. Menu it. triangle desired designs/stitches set swipe the a panel with the the shape be around placed Available Touch load shape, in Menu of Shape Shape with shapes Embroidery more category be to function. colored will loaded. select ways the in new the Shape size colored horizontally, to a between the will add moved are in Shape vertically, shapes. Last shapes. Letter same placed. shape shape the Available to the be on Open available the be the listed they the on Creator different swipe letter listed more can Design Letter Shape Started to how to letter selecting designs Design Letter Shape drag All are it a that change shapes. are open see two a a a hold within to The on Load Load Load Shape and Creator. to Panel in or & about When want order different Touch shape Repeat/Duplicate Note: category shape. the Read adjustments Load Touch the categories categories. Touch Load Shape. Load Touch Getting Touch Shape shape different horizontally, shapes swipe Touch corner Menu touch you Shape Creator adjustments Note: Repeat/Duplicate Multi-Touch You Touch your shape Read Rotate 9. 8. 7. 6. 5. 4. 3. 2. 1. Touch Edit the shape. Touch Load 154 Rotate Move Control Edit Settings Zoom Zoom Zoom Detach order can shape. When about in Edit Edit Load Shape The a move, two that Slider to to stitches Stitch selecting to to to Wheel how Stitch Hoop All Screen different the close open they rotate, to shape Last to are will add the the a using select new scale ways loaded. will control function. control be more shape, your placed be a and with desired set designs/stitches window. window fingers. all pan to the along your default. directly stitch Combination custom for the to adjusting baseline on your onto the your in 17. 16. 15. 14. 13. 12. 11. 10. Delete Combination Duplicate Set Full OK Positioning Scale Number Screen Last View of Repeat Design Designs Rotate Shape Creator 155 Degrees 90 Rotate icon the current handle The of rotation the the selection degrees rotate center 90 the the adjust clockwise. shape the degrees, screen. in to in the on the of icon degrees on touching arrows touch top shows, 90 by the the Rotate finger Each of shape use the shape arrows your and the shape. center touch selected move selected the also angle. above Wheel in the the and selected can the rotates rotation of number located frame You Control Rotate Shape Creator Combination Scale unlock Touch height. with By the adjust move handles Scale size You With chapter. how not Note: design Touch OK. number stitches Touch added Touch Last different Add Touch already 156 default available arrows to of can function. more a Duplicate/Delete the the your adjust the closed OK the the between the design/stitch the to and to loaded. in of also ways scale selected Embroidery size the Combination Duplicate padlock selected in designs/stitches the the designs/stitches shows finger activate when your touch the padlock shape proportions function, corners of with the Shape the shaping text shape on current Repeat/Duplicate in shape. the – individual the in Last in selected the and or the while in Edit. of Scale the the Creator Combination Set you Repeat by screen. the the an center icon + width same are shape. shaping touching Number to onto you embroidery center can icon shape shape. open to locked. scaling icon window of want and increase order your duplicate and the in of selection of a to The one height. keypad the Repeat/Duplicate Designs/Stitches the use to shape Control This as of text. add add Embroidery to numbers of width or the Control the the Last is load designs/ Read the decrease frame in ones and to indicated arrows Wheel last two scale and set the about touch Wheel. above and the Text the to to are 2. Combination 1. Scale Duplicate Scale True unlocked locked Size Last Repeat Shape Creator 157 All Hoop to Slider to Zoom Zoom Zoom 1. 3. 2. in you the touch will zoom design(s) number much and Enter to Hoop the add to how designs/ in to and/or right of see keypad. the Zoom a touch hoop. want will to stitches number open you You shape, the to move slider. selected total + out. all and your Designs/Stitches the the the combination. and in fit – of show zoom to enter Slider to above the will want to designs/stitches left area All Options of you Zoom the the to want stitch/design zoomed Number between to the the you Zoom in adjust Use and have Zoom Stitches If Set area number OK. Shape Creator the attraction percentage Use control The make When points. For Select Contr Touch Positioning your Positioning selected editing possibilities. square. An A they Each A 158 selected control unselected selected each adjustments the define shape. shape adjustments you the Select ol Contr points. the All slider shape shape, point percentage, Positioning Points control have points. control of what is control control all built ol the to control can is there selected Points or increase made the selected a point By to be points by some window point points. shape the are changed adjusting the several point icon will is a shape: of pre-defined or affecting closer are control marked set in will only the decrease is to visible Shape of control marked with make control the look move, the control affect points. the with control baseline unlimited Creator, when like. adjustments the points. sets selected rotate the with points. a points, attraction The filled of selected you points, an control will Together and to higher outlined shape. are square. you open be scale. to the can to the the 2. Unselected 1. Selected control control point point marked marked with with an a filled outlined square square Shape Creator 159 Right Curved Up 2. 1. to on The top, the You the the shape. to The on Select or objects along each). above decreased positioned positioning actual bottom, baseline. all or be baseline. the the baseline, baseline. the baseline evenly shown on the shall between on selected affects the is the the place of to on that increased The to gap along objects objects top be setting shape. designs distance the all on select can objects actual objects the parallel The the objects baseline. same on can the affect the The spaces the objects the of place the objects angle. of placed You will Angle to align the objects Positioning the Positioning side slider. to setting side under all how the objects current (placing or place setting left Line Side Spacing how baseline. Design which or the the can affect default between select shape. ed the using keep the Decide have right selected Fix on Select Select baseline gap by slider. Select You The can Select baseline will Shape Creator 4. 3. 5. Creator 2. and You your highlighted. design 1. Shape shape If Edit 160 you shape, and scale To hold Add Touch on to Touch In new embroider Touch select can Shape. Embroidery the in want the change Existing and move again. shape. designs also on handles Embroidery Menu screen. OK a Shape Edit touch Cr you a shape to Touch touch design your eator to the your make in will Panel, the or confirm Creator in Shape size to Edit. finger & stitches to the shape. Shape rotate see any or load Edit, hold open of you Ex stitch corners Touch that Creator changes the in your on it. handle touch to erc will onto the Embroidery A Shape shape, the to open created Embroidery shape Shape of ise find load to the screen. to to the on the enter Creator select touch an shape. different it line the selection Creator shape Smart to already To Edit the screen. the will your one Touch rotate will Stitch-Out Shape and to shape Toolbox shapes. be of to shaped frame created start be the edit shown load your & line. a to it Appliqué Creator 161 the of easily choose to edges garment raw stitches or the quilt autofill cover your to to different designs appliqué mini twenty appliqué. an or are new add a there can stitches create You to machine Edit decorative Creator. icon™ choose Embroidery Appliqué also creative oduction in the can your Intr eator In with You – Creator Cr Creator. appliqué. eator appliqués Appliqué Cr the Touch Appliqué Appliqué decorative creating the Appliqué Create 11 using when appliqué. Appliqué Creator 3. 2. 1. Appliqué 162 WiFi mySewnet™ Help Signal Center Crea Strength cloud tor – Overview 6. 5. 4. Control Scale Rotate Handles Handle Points Appliqué Creator 163 Stitch Shape Help Panel Menu Design Autofill Letter Shape Load Load Load Load Menu Quick Main 14. 15. 16. 17. 18. 19. 20. folder cloud View Stitch Screen Edit Settings OK Full Positioning ™ mySewnet Load 8. 9. 10. 11. 12. 7. 13. Appliqué Creator mini mini ready letter vertically, you touch Menu corner Touch change horizontally, Shape. shape mini Touch Load the Touch Load you All swipe shapes different Touch Load Appliqué Touch Cr Getting Note: enough 20 the decorative If vertically, 164 you different eator shapes different number want want design design. design When shape & to or Panel select to and Load Load Load Appliqué to within to stitches hold Autofill a a be see open shapes. change it another Creator. a swipe swipe has stitch drag you Letter Shape creating embroidered. desired to autofill to of Started you Autofill Letter Shape can an more letter swipe on the be the load the a can autofill to on be satin the can Creator to to or Available the placed. same stitch Letter stitches/designs shapes. shapes. fill Open edit Shape in moved an see see the it. a stitches. between stitch/mini Stitch colored easily size Stitch Shape mini the the stitch All applique each all all. colored stitch category or with Shape the in of Menu in entire If letter letter Touch design Available a around in change shape stitch/design Embroidery the you ready the Available panel Shape mini the it the using will triangle Menu window. shapes design. Panel Menu shapes. shape. Appliqué want categories. are on Menu categories you design to top to on Menu you fill a a listed shapes be a decorative another to to the shape will Panel stitches to has If the desired in individually. embroidered. want Panel Touch Edit load access The selecting move you to screen. the need shape vertically, a All are load are to to satin to entire a to can lower to stitch are on access stitch/ load Letter where the available enter stitch/ listed listed add. to access with a Simply easily a stitch listed a set new it. or the If a Appliqué Creator 165 in in your your your onto onto for your baseline baseline to the the custom custom design Combination Combination stitch default. default. your your along along the the to to all all function. desired designs/stitches designs/stitches set set desired a with with a be be placed placed shape, shape, more more be be Design function. will will loaded. loaded. select ways ways new new select to a a will add add will are are to Last Last shape shape to to they they the the different different Stitch Design how how to to selecting selecting Stitch designs stitches Design that that two two a a The The Load Load in in about about When When order order adjustments Load Touch shape. shape Repeat/Duplicate Note: shape. shape Repeat/Duplicate Note: Touch the Read the Read adjustments Load Appliqué Creator Multi-Touch You your Rotate 9. 8. 7. 6. 5. 4. 3. 2. 1. Touch Edit rotation number rotates of Control You frame located Rotate 166 the Rotate Move Control Edit Settings Zoom Zoom Zoom Detach can can shape. selected and Edit Appliqué the the in Wheel above angle. move, also Slider to to the selected move selected to Wheel Touch Hoop All Screen touch center open shape. the and rotate, your arrows Edit shape the shape use the using of Each finger scale Rotate the control the to by 90 shows, close your top touch arrows and touching on degrees icon of window fingers. the the pan on the in to in control screen. degrees, directly the shape clockwise. adjust the the for 90 center rotate degrees window. adjusting selection the on the rotation of the The handle current the icon 17. 16. 15. 14. 13. 12. 11. 10. Delete Combination Duplicate Set Full OK Positioning Scale Number View Last of Repeat Design Designs Rotate Rotate 90 Degrees Appliqué Creator 167 Size locked unlocked True Scale Scale to the and above Wheel. scale arrows indicated frame decrease the is the individual Control or of numbers This use the height. one The selection of and activate increase and locked. shape. and shape icon can center touching are width the the screen. by you Scale of in unlock the height. selected the shape. to current on shape the and of corners function, proportions padlock touch finger shows the the selected padlock size width selected scale also in of the the closed the your the the a can of arrows default handles move You With size Scale adjust scaling Touch By with the Scale Appliqué Creator number between Zoom you If Set Combination Embroidery about are Note: design Touch OK. number stitches Touch added Touch Last different Add Touch already Use adjust in Zoom have and 168 you the not the to want function. more Number zoomed Duplicate/delete how stitch/design want to the OK the the between available design/stitch the to to Zoom loaded. of of Options the All ways Embroidery to in area the Combination Duplicate left in designs/stitches designs/stitches designs/stitches Text to adjust your – will the above shape and to Slider enter with to when the chapter. zoom Shape show of fit shape, Repeat/Duplicate your + – the combination. the the the Designs/Stitches in to and Last shaping in and and Edit. all out. the open text the Creator Combination total selected slider. Repeat enter touch move icon + the same shape. while You to onto in you an a number stitches number open to keypad. the in embroidery to icon window will want order hoop. shaping your duplicate the Zoom the keypad a to see number keypad of Repeat/Duplicate of right and/or to shape as add Enter designs/stitches designs/stitches how to in add to the text. and the Last Hoop the to load designs/ in ones and the much to design(s) zoom area last touch Read two set the desired will touch the you in OK. 2. Combination 1. 2. 3. 1. Duplicate Zoom Zoom Zoom to Slider to Hoop All Last Repeat Appliqué Creator 169 square square outlined an filled a with with marked marked point point control control Unselected Selected 2. 1. the the to can the to scale. be open you square. are shape. outlined higher to and Together will control an points, you selected of filled The attraction points, a points. with the rotate selected sets points. the adjustments Creator like. when unlimited baseline control with the points. affect control the move, look the control make with marked Shape control of visible to is decrease in the only will set marked control are closer affecting or pre-defined of shape: a is will icon, point several the adjusting changed are the shape points. point window some by points be to By point a selected the made increase or Points selected there is can control to the ol built all control control is what of control points. have control Points Positioning percentage, point shape, shape slider All the points. Spacing Contr ol Select the you adjustments shape shape. define the adjustments each selected unselected control selected A Each they A An square. editing selected possibilities. control Use The percentage attraction make the Select When Select For points. Positioning your Contr Touch Positioning Appliqué Creator can slider. by gap baseline The 170 using select between default (placing the left setting slider. the or right objects the spaces The same justification actual can the distance be objects gap increased on is between shown the evenly baseline. or decreased above each). along The the the You Appliqué Creator 171 Right circle circle Curved Up the 2. 1. the of into out tip tip the the with with Heart Heart 1. 2. to on top, the shape. to The on selected Select selected or objects positioned positioning actual bottom, have your all be baseline. the of the baseline, baseline. you baseline on the shall selected affects the the the place of when to on that The to along direction objects top setting shape. the all on select objects objects the parallel The objects available flip baseline. on can the is affect the to the objects the of angle. of placed You will Angle align icon the objects Positioning Positioning side to side function Stitch. under Flip all objects current or place setting left Side Line how the baseline. Design This which or the the Stitch can affect shape. ed the Autofill keep the Decide have Touch stitch. an right selected Flip Fix on Select Select You Select baseline will Appliqué Creator 4. 3. 2. 1. Cr appliqué If Edit shaped highlighted. Appliqué and You your 172 you shape, and scale Stitch-Out load Touch To line. from embroidered. All it. when different a Touch eate select can new Appliqué. want change Existing shapes design move it also handles the in creating Creator appliqué. OK Appliqué to Edit touch Appliqué Embroidery to Autofill shapes, Touch Embroidery touch your to to the have make and in the embroider confirm in If Appliqué size again. your finger the & to you the a Appliqué In rotate Creator letters any Stitch satin hold open of the Appliqué corners appliqué. want Edit, changes the your Edit. on Ex Menu handle to stitch Menu and the Creator your in appliqué the open er another touch created Touch Embroidery Appliqué of numbers screen. cise Panel, ready Creator appliqué. to Touch to the on the to to an load the Embroidery selection stitch, touch enter appliqué select Smart already to you To a screen. to it will Creator be shape to rotate Edit choose will the one select your Toolbox the be frame created and find to of to shape to your one start the from load edit Appliqué Creator 173 on will raw fabric. fabric outline stitch the stitching base straight stitch the the appliqué cover appliqué to outline to the another will the straight your close a fabric as sew over where that three sew will fabric sure show fabric block will appliqué to block Make the color block appliqué. in appliqué color fabric appliqué outline. Stitch-Out color your fabric. secure the possible. base of to your excess second first stitches as base the sewn. The The covers on be Place stitch line The the Trim edges 3. 1. Appliqué 5. 2. 4. Sequence Creator stitches In Sequence 12 You Creator™ 174 Sequence can Sequence and see feature how stitch Creator, Cr long can fonts eator you also your from can be Cr actual — the inserted create eator machine, Intr sequence and in oduction adjust a sequence. the is in mySewnet™ a the sequence information You can of cloud stitches. create area. or from sequences Combine a USB up various device. to approximately Stitches 9mm stitches, made 500mm in side–motion Stitch (20”) long. Sequence Creator 175 Window Stitches Settings Width Between Step Stitch Stitch 4. 5. 6. Overview cloud – eator strength Cr Sequence mySewnet™ of to signal in Sign WiFi Length 2. 3. 1. Sequence Sequence Creator 15. 14. 13. 12. 11. 10. 9. 8. 7. 176 Delete Duplicate True Full OK Cancel Keyboard Stitch Stitch Screen Size Settings Length View 23. 22. 21. 20. 19. 18. 17. 16. Menu Load Load Load Sequence Directional Mirror Mirror Stitch Font from Panel Side End Commands mySewnet™ Stitches to to End Side cloud Folder Sequence Creator 177 is can the to will add. stitch fonts in to & cursor a drag Panel Menu Touch to using and arrows font you then more the a total between select the letter and position stitch the touch at cursor create and in Menu want see or letter stitch. stitches. and possible The it a a where Available Available to To Use the is Touch it shown touch sequence you stitch/stitches active font it at placed stitch simply desired entire add add stitch font. are a the Mode. you stitch. The be to to swipe more. move available if The Sequence letters touching desired placed to selected sequence. sequence. will see screen, select the a by want want selected the sequence desired be selected to Sewing through top a desired the the the a the sequence of with corner. the to you you sequence. to in view will select the on it expanded touch the it stitches It to Only horizontally, swipe panel the and sequence. select cursor category in be sequence, sewing lower a to and load to add where where a select number the the it letters, can the to around listed green. cursor placed. anywhere Inserted and Started in colored Font and The When a ont in Select stitches are load be cursor cursor F Stitch from vertically, Move stitch of by the creating subcategory to a a keyboard through moved a Panel the the Load a and window Stitch it a on sewing be arrows. arrows. triangle listed eator start adjusted. marked step to start are open position. the number the the can want touch Move Load be Touch stitch hold position. Load Move Cr Load categories categories. touch Getting To Menu sequence be Panel marked Sequence Creator It insert To Replace Duplicate Delete Adjust adjustments density You sequence. and move If Touch and exact Note: selected want To 178 will you replace duplicate the touch can Make to number the the be want & copied or duplicate. stitch. mirror, hold a text placed cursor new Delete. position a your a Stitch to stitch; work a stitch a Stitch of to delete stitch. stitch, and adjustments Stitch adjust at copies to get Touch just Touch the includes simply the of or a stitches a move the pop-up or cursor like stitch stitch length you Letter or & the selected Letter select in hold the the on want Letter or or Duplicate Sewing position. and where the adjustments. cursor letter, letter to it, to stitch stitch. width delete touch insert. you you Mode. touch to before icon the The or can Delete the want change the to stitch whole duplicating enter copy to stitch and delete you the the the or 1. 2. Mirror Mirror Side End to to End Side Duplicate Delete 3. 4. Stitch Stitch Length Width Sequence Creator 179 Stitches Directional of at and you or in pop-up. access insert length sequence. to a a the angle different shapes in sequence stitches stitches 16 with Panel new the duplicated in touch which in move stitches Menu used to stitches create select directional the be deleted, selected, to can in inserted be is the can between be straight possible you Field can it and are angle will and Stitches closing Stitches borders. Stitches stitch. Stitch 1mm makes a stitch Stitches position. Directional intended without angles. one insert directions the Directional the large-area stitches to Directional and ectional Directional cursor When want icon the The mirrored Touch directions. Touch different approximately Add various wider Directional These Dir Sequence Creator it’s Saving Touch T Sequence you Note: performed and Insert several you This sequence. a Move to Insert removed. you the Note: sequence. You Use sewing the into You 180 rue command. Tie-Off beginning original sequence program to the it want the can can is The If create the a a also True useful creating rows. it. Size Thread Stop Tie-Off sequence. insert insert commands cursor to and This shows in a size. Size a them. sew Select command and and sequence the for Sequence Cut the Tie-Off, confirms a Cut command Commands if to end sequence it example sequence. where will These Tie-Off you the only it the will command will and always in threads position want Stop if appear once that the between. commands be an in you at commands if added embroidery and command you icon the the the or be want on if and where to end sequence you Thread command performed want The the automatically, will create raise the will screen of want commands be anywhere a you mode, will the machine secure the Cut added be a to the sequence in sequence want is be included when presser commands Tie-Off return the inserted machine allowing Tie-Off. can into in to order to the stop. be add to foot. at the in if in 5. 4. 3. 2. 1. Tie-Off Sequence Cut Tie-Off Editable Command Beginning End Stitch Commands in Green 1. Save button Sequence Creator 181 List View in loaded Folder be stitch will a Between New as Thumbnail mode sewn OK Close Create Toggle and be 6. 7. 8. 9. not embroidery can in and Device State created design USB Area a a mySewnet™ as to To Current sequence Mode. Name A saved Save Save Selection File Save Note: and Sewing 1. 2. 3. 4. 5. or by by will on Then the type. List create can button, In you file name file folder the hold To OK. Mode into Manager. pop-up you & a window file and stitches, to and folder between your File icons. save save. using cloud touch Embroidery and in to Sewing touch with button. in close pop-up new file and Sequence name pop-up and to Name toggle it files designs, it OK will sequence to file button the save your shown simply create pop-up our thumbnail the file. Creator open the load Y is the ™ mySewnet saved your as saved shown. Save the close View the to the In keyboard Creator. name pop-up or file the in touch are with the folder, of your load the to a list touch then OK folder save a each oider Sequence and to Creator. sequence, screen. will process, file fonts it, touch in image the shown Previously using The Sequence Thumbnail the the OK save is touch View organize on simply save file, in stitch files open Edit. to on opened Embr to and file and/or to and the save keyboard folder Close. OK Sequence the device. hold your your to or List to folder, want have how & the the thumbnail each touching folder. appear a USB folder cancel save sew Thumbnail a you you new touch showing View To touching return Learn To choose to sequences using If the a name new Touch and will keyboard In Sew To touching If Edit, Embroidery Sequence Creator Sewing If sequence. sequence. affect in In Mode Using Sewing touching To Adjust 182 you the Sewing adjust the sequence. want Mode chapter. OK. and entire Sequence the In Mode the to Sewing entire Adjustments touch edit sequence. Use Embr Entir it is each sequence, the Mode the possible e stitch sequence arrows oidery Cr Read Sequence you made eator to in enter can about to start the in and step edit Edit sewing Sewing sequence sewing Stitch the in through your Edit Sewing mode Mode Edit anywhere entire loaded Sequence the in by will the to Embroidery Make Toolbox Note: Sewing again. be Edit If Edit sequence In will you Embroidery highlighted. be touch icon Touch your want Make highlighted. to Mode. and/or just access the adjustments and to Edit. your like sequence edit Touch Edit Touch hold Edit Stitch Touch when adjustments a you Touch in in sequence cancel to the Sequence Edit and editing and can Cancel open stitch to icon. make to touch the enter loaded Sequence and undo. field a Creator. to Sequence design changes undo. OK Sequence touch area to to to Embroidery Creator by load OK Creator open to touching Creator to your it the load to again. will Smart it the to Sequence Creator 183 199 to to up appear. stitch up stitch exceeds be stitch will the Reached a can special in contain make Been sequence and and message insert Sequence will Has sequence stitch to long in Sequence add the pop-up in to stitch If (20”) Stitches buttonholes stitches. possible this of mm Your trying Added not 500 4-Way are be length are example long. as commands. Messages Number you for too and such Cannot stitches stitch maximum eator stitches the sequence approximately The Cr Stitch Some Pop-up sequence, menus Maximum Stitch Creator™ Feature Creator™ Stitch you The create In Stitch 13 184 theStitch width to a Creator™ create Stitch stitch Cr feature of Creator™ the your eator™ all feature stitch on icon. stitch. Cr your feature, field eator™ can Your own F eatur is be 9mm or stitch you used alter can e and can in F – already create both eatur maximum Intr be saved Sewing completely oduction built–in e to stitch Mode the stitches mySewnet™ length new and stitches or in is letters. Embroidery 5mm. cloud and The adjust folder grid Edit. or every and To to the a open, single USB vertical just device. stitch touch center point. the line You Stitch will can help Stitch Creator™ Feature 185 stitch) current (shows All Select Arrows Preview 4. 5. 6. Overview – e eatur F cloud ator™ Connection Cre WiFi mySewnet™ Multi-Select 2. 1. 3. Stitch Stitch Creator™ Feature is Multi-Select If Select number current touch To between selecting To Select point Each points. through A Definition Cr Getting 7. To The stitch 15. 14. 13. 12. 11. 10. 9. 8. To Use the touch is If deselect Note: stitch marked 186 the the white white stitch mark select select select Move Triple New Full OK Cancel Keyboard Edit Zoom position, eator™ next first the stitch If icon icon is point points the Multi-Select All selecting them stitch Screen indicated Up point stitch it it is stitch the number Stitch will Stitches/Stitch the a all the more Wheel Multi icon. Slider Stitch is is is is the stitch point arrow is Started stitch fabric. deactivated. deactivated. by previous green, green, after Y=feeding stitch automatically position of indicated is point total point. than Point View touching stitch Select the with point, a is is by the points to and points Stitches number indicated it it Stitch the point and one select an means means points marked Stitch or icon is then marked just length) by the outlined stitch the with shown next at next where stitch a and Down are the touch be using of Position Point Down touch that that filled by stitch Points stitch point, stitch selected to connected same use stitch between Stitch a the points it it square the arrow. the it dot. square the is is arrow the point on point. points. needle the marked Up (X=stitch time, activated, activated, point. arrows A screen. as arrows. before (A). arrow, stitches selected the in to (B). well. by touch goes The your select A arrows. stitch stitch to If needle the you marked The and and select second in the stitch, stitch the can point, if if it it 23. 22. 21. 20. 19. 18. 17. 16. Stitch Load Load Mirroring Mirroring Delete Duplicate True Size Stitch Font Field End Side to to End Side Multi-Select Stitch Creator™ Feature 187 All Select it If of if will see stitch the the stitch your and on you field change. again. the select zoom, be actual actual preview stretching. marked several touch using a on help will icon wheel. can the the point. will stitch the and in 100% activated, time, the will the for at the you lines having Screen is ools in focus stitch shows shows of it zoom T line This Creator™ same grid lines touch the pinching (Y) (X) point, when that you lines the the all, by arrows If grid Edit at center Stitch like previous appear. stitch wheel wheel Slider, the edge in the Multi-Touch means the or the look fabric. it in/out the the will the deselect points between the stitch Zoom from the will To on from a stitch point. eator™ only touching zoom between stitch above above green, on the deactivated. stitch is is Cr by icon. out, distance your stitch all also it stitch length All or position 1mm directly using making All point. icon the the created can number number distance select move eview visible. white the To Select If is feeding needle stitch The points fingers The Move To equals When Stitch Zoom The marked field, zooming You your what repeats. be When Pr Select Stitch Creator™ Feature Delete Mirr T Duplicate Add stitch If Touch touching stitch points Note: and/or The Touch Note: will want where Touch be If point If stitch Touch selection You 188 riple several you you duplicated selected be can Only Only to oring and point point points a want want you in & the & the tripled. vertically. insert. Stitch Stitch also hold hold shortcut Selected the the stitch use Triple icon enabled enabled can and is to to will stitch stitch delete add Selected selected, and Duplicate on on delete duplicate enter to points touch Stitch or create the the an insert in if if inserted point(s) field. icon. more more the existing Stitch the Duplicate Delete a Stitch the are single they icon a one menu to a exact than than new Stitch Delete selected, stitch create will after will icon and single stitch Point stitch one one stitch. number Point bar icon be point, the all the to icon. a stitch stitch or mirrored Point stitch from copy. all point, delete be marked to selected the stitch deleted If select get of point point the more point. Selection duplicates select all a pop-up horizontally stitch points stitch is is the stitch(es) stitch than when selected. selected. The the stitch Menu. point. will one two you 1. 2. Mirror Mirror Triple New Duplicate Delete Side End Stitch Stitch to to End Side Stitch Creator™ Feature re- 189 in will and design return return have the then Stitch Stitch will will created in you and stitch and Creator™. Stitch you you area have Stitch-Out in entered stitch Mode Stitch embroidery created design. created you the in you Edit an work have your the Sewing Creator™, , Creator™ open stitch when Select in on you Embroidery without become the will embroidery to feature, Stitch Stitch hold active will stitch stitch . Creator™ Go in in mode appear. is a stitch and Creator™. Edit without regular OK. will stitch Edit the edit Edit a Stitch Cancel Cancel another Creator™ to as in touch and Stitch mode touch idery out in . Creator™ Toolbox want touch touch select it Stitch you remain Embroidery sewing you Embroidery you you you Creator™your If Embro If once stitch to created Creator™, Smart Creator™ If If open to Stitch If not a in that or will work used it. folder stitch Save so the will in right be Sewing Stitch Edit the Sewing to the save The stitch folder to in to information. sequence. stitch on when Stitch Creator™ cloud can open when to design. a stitch active lower in appear a OK Select a the Sequence Sewing is either touch hold activating stitch. cloud loaded more as the edit Edit. in as loaded created in loaded Stitch will in in feature where open be in to created Edit for Creator, be and available after Stitch The appear. saved sewn saved used OK be touching will mySewnet™ will Creator, when mode. will want is stitch position be in be pop-up decide Stitch will touch entering not the A your an A versa. mySewnet™ Mode feature Stitch Creator™ touch Embroidery stitch when stitch to sewn. can other Stitch Sequence and stitch stitch design Save will Stitches Stitches a or Embroidery cursor in In be when vice cannot Edit. the the The mode locate select the See Toolbox to stitch made screen. Stitch your active saved to the stitch and and feature and , Creator™ Edit active is when in Mode and at made and be oidery Sew Creator™ active Edit the the is Stitch confirm. eated eated screen. ready Smart sewing Edit Edit (X) device. sequence. can created a embroidery to is was Mode feature, Stitch in Mode a stitch Cr Cr stitch the Menu the Embroidery Stitch and name created created an a Sewing Mode. Mode in the oidery of inserted outside of a USB Save OK Embr transferred Creator™ Creator™ are or and that stitch a device. and be can be eator™ eator save sew to part Embroidery stitch stitch Sewing you Embroidery not A become Embroidery Sewing as Selection A Mode Sewing opening Using Cr will Touch Stitch Using In Embr Stitch USB and Saving To Sewing If Cr . Creator™ corner mode feature; Creator™ button you Load To Edit If area Mode Your created or Touch Stitch Creator™ Feature length 500mm point Your and Creator™ Some Not Cr Pop-up long. Sequence Creator™ 190 eator™ four an stitch you stitches this Editable (20″) direction are feature. Out feature. pop-up sequence Messages long. trying are of F Stitch eatur not Range Buttonholes, If stitches will to the can available add let sequence be e you cannot will up in know to to stitches make Stitch edit approximately be exceeds opened that the in wider Stitch stitch sequence the in maximum than Stitch or stitch 9mm too Help Center 191 its about more learn and Window machine Previous icon™ to Help Settings creative mySewnet™ WiFi Quick Return 6. 7. 8. 9. your use to how on information find oduction will Intr Overview Tutorials – – you Center Window and Guide Center Started Guide Center Center Center Help Help Help User’s Getting Techniques Stabilizer the 1. 2. 3. 4. features. Help 5. Help In 14 Help Center User’s your Here Touch alphabetical User’s divided the You features 192 Category. can creative you Guide. User’s into of see will Guide the the order. categories Guide icon™ The The find machine User’s category index information to machine Guide open following are. option option the by and about shows built-in Index the what shows structure how topics or the User’s the by to different looking in help operate of Guide. an the topics in 4. 3. 2. 1. mySewnet™ Category Index Navigation Arrows 7. 6. 5. Window Return Quick WiFi Settings Help to Previous Help Center 193 Window Guides Previous to Start Help Settings Quick mySewnet™ WiFi Quick Return 1. 2. 3. 4. 5. A it. the with more. do machine, instructions touching to and the by 6D has in Unit IDT™ Foot System that Step-by-Step the animations. threading Needle help as interested Spring IDT™ with Thread show Embroidery find are the such Threader Hoop Stabilizer Through open the disengage will will you Upper Dynamic the Bobbin and and will you Needle the the topic machine the guides Started Winding Winding Fabric the the On/Off engage Viewer section of which of to animations. Threading Automatic Bobbin Engage/Disengage Bobbin Slide Inserting Attach/Remove Hoop Attaching this Some Select Project In how and • • • • • • basics • • • • Getting Help Center your technique and/or medium available the with etc) need In exclusive different project. depending adjust In , different In Sewing In Garment T different Touch Sewing-, to category technique 194 echniques open each each this this chosen depending images project. to the to section section project project animations. adjust The it. pockets fabric. to kinds sewing categories Quilt- open in sewing setting is category T technique on see echniques the stitches filtered T and/or When echniques you you what the Techniques you you of the on content and etc. techniques techniques of sewing setting what and will will projects and will will selecting to fabric The Embroidery-techniques. the are out animations. is choose find find filtered tab. stitches then find find always for fabric stitches T techniques of type and utorials available. you. tutorials tutorials However, the for an Step–by–Step etc. select a from type stitch Tutorials. you out set instruction garments stitches (length, needed However, The for a such for you are technique from about about such stitches Touch sewing you you using (length, are width as for There such as the instructions may Garment-, with how how you and using the on the Select needed for project in etc) as sub- a chosen may are are need width to to images woven your project collars, for sew sew a for to 5. 4. 3. 2. 1. Return Quick WiFi mySewnet™ Tutorials Settings Help to Previous Window Help Center 195 Window Previous Guides to Help Settings Stabilizer mySewnet™ WiFi Quick Return 1. 2. 3. 4. 5. on for is that sew sew using They (length, when stay to to and etc. shown cutwork as are stabilizer this is group. needed will technique. stabilizer However, in available and how how stable. water. stabilizers temporary about piecing, technique a It you instructions instructions fabric the such stitches stabilizers in the as are after you. lace find another top the more stitches are type about about all chosen Select stabilizer embroidery for of within such specific tab. will . The the stabilizers your the select project. out have remove fabric dissolves the information techniques you for to Step-by-Step Step-by-Step stabilizers Guide. The to tutorials tutorials setting using for also stabilizers your that standing about Content what embroidery more embroidering by find find the to stabilizers filtered between easy find find techniques You on viewer free filtered the is the see animations. category are will will needed in will will Stabilizer the when away to body echniques quilt embroidery stabilizer: adjust T Tear-a-way . this batting stabilizers Guide of of make you you Cut-a-Way the to different cut you you They images. add uses. In information and/or echniques to found Close are be useful Use T to technique settings depending be soluble open need kinds kinds to view The embroidery, with project. stabilizer etc. all embroideries project project oidery section section to a you. to etc) fabric it. very special group. can images may viewer. chosen your for embroidering for stabilizers. Tear-a-away: Specialty: category are embroideries Batting: needs Water Cut-a-Way: the backing this each this each the a use • • Touch • in • • group Touch in to Stabilizer Embr In In Quilting In different width for different cutwork together built-in They viewer, set In the with you Help Center Pr Pr All them, Some open When can The Use embroideries In see instructions, Instruction There touching You instructions. reach moved touching touch on shown be When When 196 the opened. oject the ojects images to be step the can showing icons projects the be you are content you you loading screen. very in around arrows decrease with able one the the Project two Viewer will touch have can The and that helpful images Close Project of you to a When tab contains tabs you a load be on or Viewer green Content. the may selected do project on Viewer or you need enlarged swipe you that how or the when A the the increase and the Viewer be Minimize frame icons. will screen project. Stitch you for can stitch from Play hidden to Project vertically a animations The icon looking project, make find the by be can is which icon, the the Instruction icon, that so to minimized touching the specific the when Viewer toggle icon. expand. that that text Help at is a active a to and stitches is video Project needed the that you particular in go It always following Center project. between, when can is the on list to step. tab you will minimized, or player the them. and/or Viewer also Viewer of for contains closed accessible you need it be materials. next part. that will be the able will This touch to by step. will by be step. to all 1. 6. 5. 4. 3. 2. 1. Project Decrease Project Step Minimize Active Instruction Project Between Step Viewer Steps Viewer Text The Size Icon in the Menu 12. 11. 10. 9. 8. 7. Current Close Content Play Expand Increase Panel Window Step Text Size Help Center 197 or Forward, View Fast forwards Forward Screen close. move Rewind, Fast Repeat Full to to 5. 6. 7. Slider chapter. window the Play/Pause, Icon can current drag player or you also video can video opens the Chapter/Section Slider Rewind Play/Pause You that entire 1. 2. 3. 4. outside the beginning. player On/Off. the touch seeing video View also from the can In between Screen You Full animation X. toggle the to the turn animation. icon start and the to touching view Repeat by to /Section on animation. Rewind icon on the in Chapter Play animation hold Player animation the & the the the Close Touch Touch Touch set backwards Video File Manager folder 9. 8. 7. 6. 5. 4. 3. 2. 1. File File Touch File 15 198 Rename Copy/Paste Cut/Paste File Selection mySewnet™ WiFi Quick Return Manager Manager Manager or Main File Information Signal to Help To a File Menu Area USB is Previous Manager Strength cloud used or device Folder and – – to folder select Overview Intr Window open connected oduction design File Manager to files, your font tab creative files to open and icon™ the stitch File machine. 17. 16. 15. 14. 13. 12. 11. 10. files. Manager. mySewnet™ Built-in USB Move Multi-Select List/Thumbnail Delete Create Store Device Up New your Designs One cloud Folder saved Folder View folder files in the mySewnet™ cloud File Manager an or 199 into USB file be of the a or of USB the will Design it. path images in it upwards cloud loaded the when ™ mySewnet View area. to file load The be file, content the to finger List content. the in will font area. The folder file it the thumbnail available your have it. ™ mySewnet as about the connected file, stitch only view stitches the you a with current open machine. is if selection hold font to and and & the device load on older the touch icon your F in Swipe displayed Creator. in you to information fonts USB scroll folder are or a If Touch selected. a to Device to content, read embroidery on written Device. shown files depending or Edit. area. to is File Sequence View an the designs, be USB a USB connected hold font file icon into is a & or will load The folder your folder an and downwards display you and Thumbnail To folder cloud ports. device files with Store Open Touch information loaded Touch If Embroidery folder open at file not will the .XXX, is your cloud and your fonts files) that by with File fully .PCS, a selection or message Multi-Select in Copy cloud. following to not the in .PES, use. are in the mySewnet™ mySewnet™ While folder pop-up supported stitches to files/folders to a files (embroidery the load .PEC, of not signed shown automatically icon. to is want mySewnet™ is older can are another F it .DST designs, .HUS, you to fonts file) you connected destination about and embroidery version If e.g. file. files combination and .VIP, machine the file font several and a .10* same damaged, Multi-Select Read of Cloud Manager the or synchronized files is machine. the load the files) be .DHV, file) select file .EXP, to icon™ type stitches to machine. touch File your account cloud. to the will versions file load touch the unrecognized by selected .JEF, or .SHV, (stitch ormats (embroidery (project to the trying an on want files F the creative If If Some designs, as time, owse .SPX .SEW, .VF3 .VP3, .JOS shown. activated, you mySewnet™ mySewnet™ Save area one is Paste possible folder saved mySewnet™ • supported Note: machine, If Manager. Note: Multi-Select • Br formats: • • Note: be Your File File Manager Rename Cr File Below Organize Move List/Thumbnail to connected The USB display & the Use way through separate Touch many This In a In view showing you in Touch file message and To 200 thumbnail hold explore the list thumbnail eate change files or Manager. USB the then can to makes each view current different folder. are the the the on Device all up move and enter the headings; opens the Device touch New instructions create List/Thumbnail file it. a to the of first all it a folder One levels image folders files the the view easier position. a up is File name files file where the level. name F shown icon machine. new connected one in older F of to each Folder, types rename are of or older a to for of folders. open is In View folder list for folder the you find on sorted a A F only each with the file file older in your or file. pop-up how Touch can Stitch, it. View file a the Level selection is devices. as level icon or active level the specific You into shown folder. thumbnail enter to or folder, same file icon to the organize Design icon message folder can as categories when create name the Touch you folder. file USB area with to step to touch new icon. toggle if step and step a icons. you Device a and file up opens your you USB a new to with name USB Other. up A up. all name will file select between have device In pop-up files folder the where icon Touch device type. list see for and in it to a is Move List/Thumbnail Create up Rename One New Folder Folder View Level File Manager 201 Cut Paste more icon. new another cut move removed selection. to the is the and the in touch select folder(s) place folder(s) to stored to or then or time. able now be and want same file(s) file(s) to and the you The older move F folder(s) to folder location icon. where or or Multi-Select paste and/or paste File file(s) folder original file and a the the the Activate its one cut Use location. Select Open Touch from folder. Note: then Move File Manager different another Folder mistake. screen. You the When Delete Pop-up Delete Copy Note: (s) more Touch Open Select location. Use stored deletion up touch To within confirm icon. To 202 still delete delete message deletion copy cannot then A Activate the & the deleting in the the Already exists File This pop-up a folder the hold of level a the one all a and folder file(s) File Paste folder all file File or create deletion. will will Messages in files new file in the Multi—Select paste content. Folder or on the or a or message the Exists or where icon. and/or appear prevent file or enter delete are and folder, folder the a pop-up folder(s), F previous to new older or F deleted If same The folders older copy a you folder folder, a icon so and different will folder select you folder file(s) message that to level. want file(s) then in for the at folder. as appear shown from be you it the you with well. is able a or File original and to Create touch name few deleted, or same deleting will folder(s) that place can to so in the folder(s) touch seconds. select Manager the need that time. the for confirm appears your same file(s) the all active the copy the anything you is and to selection. files folder to name now folder. or A confirm delete move can the another on icon. folder, pop- folder on as by a Delete Paste Copy File Manager 203 Loaded be space, by same machine the the is space. your Cannot to fill device up to left, space USB is free Types a loaded the to to be File continue space until not files of you can If functions Memory again, your Selected amount of you time. Multi-Select. paste Move one and small Available using full. a remind cut combinations you only not the file Combination Enough alert will completely The it using will Some destination When Not Maintenance bobbin microfiber Wipe part Remove of several cloth Wipe Clean Cleaning Cleaning Removing often. To Cleaning 16 lint Note: place. that off plate cover. pushing Remove Note: Put each Embroidery Embroidery area. Note: 204 lint keep the will the is embroidered of Check to Do When Regularly as the the No the in Place included needle Maintenance the case thread Use Turn projects bobbin be remove shown your the the the not the screen exterior lubrication area blown the bobbin cloth. Set, Cutwork using caution (B) blow the bobbin presser release bobbin off sewing cutter plate. area Under the the under clean case it and by the or with supplied design/project. any with into the the is air surface case when any lifting when machine. necessary gently Needles knife button case and foot. case Clean into the dust Bobbin Machine optional your the (oiling) the machine a Needle time by clean, lint changing the cleaning the holder (C). accessories. area. bobbin the Open it or screwdriver machine. of lifting the turn (A) up. or and bobbin you bobbin lint your accessory to is soft PFAFF® feed operating clean to Bobbin Clean the needed. threads the (A) built notice case Ar around it the the machine and Plate case Exterior up. bobbin teeth screwdriver case covering the ea needle right. up. after with PFAFF® under slightly Remove from area. Felting an bobbin the holder with well, accumulation sewing plate. with cover the and automatic Remove Ar the The the the the area clean damp brush. ea bobbin the back dust a to needle front by soft brush pop after the it and in A B C Maintenance be 205 foot foot the ON the can sewing. area. and/or icon™ the to the The pulsating not the menu. model. piercing in original then in presser Selecting 37. WiFi authorized presser the refer D guide. into the heavy does this the as motion bobbin and machine See to Changing the creative safety page down needle your for settings authorized please the free only such see to user’s OFF from when screen your the lifting. on fabric. malfunction. for inserted related set use width your lint penetrate in of Increase for the contact be set to not services, If built-in from pulsating and caused to especially firmware, machine a stitch not clean buttons described, is are selected cutter the Combination, securely contact is foot the or area the needle. as in socket. needle seem for and persists, recommendations. with designed are service. indication the teeth the with sound turn the thread not designed electricity. an wall for function needle feature, plate bobbin section mySewnet™ D machine feed plugs The with 34. correctly the not suitable does problem and helps static prevent and touch, all equipped on-screen is twin the the lift from problems accessories to to retailer bobbins retailer. and is to needle the page menu. menu. Thread/Needle that the automatic piercing that If For fabrics. lint needle sure sure needle sound fabric only a sockets sound the troubleshooting Note: connection Clean PFAFF® PFAFF® Enable Make pressure If needle Remove machine Make Needle, Correct Check Use The again. PFAFF® The feature dense and Use machine. Follow sensitive respond machine settings Deactivate settings Insert to at sound clicks For the it notch the and/or authorized you. solutions the from until local screen machine. fabrics help find into touch to down stitch your fits Plate will to your different dense it thread cover. plate machine you happy with the that sewing. narrow result contact be sound respond so or and/or cut work guide have bobbin needle sew Needle will not when not not please plate the the not do may heavy distinct embroidery feed who the a blems in does irregular does will you Press and not breaks needle Pro Replace generated emits buttons retailer (D). cutter alarm the stitch, al does sewing information troubleshooting sewing/embroidery machine sewing needle place. problems back oubleshooting this r Bobbin Fabric Thread The When machine normally Poor The function Wrong The Gener T In further PFAFF® Position the Replacing the into Maintenance The The prevent return local Pop-up service to the damage its Pop-up position. OK in Is Pop-up 206 Did Is position Did Did Touch or Are The to threader its or Pop-up center. correctly, automatic Pop-up Pop-up the the try the be other heavy home home automatic to you you you you needle Machine Automatic authorized blocked threading correct needle automatic return to OK center. message: message: message: message: message: message: damage stretchy to for using thread insert insert has position. position. weight its please needle to the eye manual home failed. bent the presser move and needle machine. a a the is the again specialty wrong contact service needle thread? to Skips automatic thread, The The Gently The The The too threader or cannot Further Touch position. needle the Needle the machine Touch cleaning. blunt? foot threader small automatic automatic automatic calibration automatic or machine. automatic needle? threader center. After your metallic remove contact Stitches OK return used? properly? thread sewing OK still for needle Further properly? to Thr local closing button to the does calibrate. to needle needle needle needle Please your or such any of or calibrate needle is eader thread threader its authorized the needle sewing flat not disabled thread on this home local as automatic contact threader threader threader threader metallic calibrate your an threader pop-up, again. Does eye. authorized is to “invisible” position. that to disabled machine its service your Touch prevent thread cannot is seems is is If home needle to Not touch not not the stuck in in to W ork Contact Contact touch through carefully thread automatic If Attach see Remove remove If instructions Insert manual thread automatic Selecting If Use Use Needle, Insert Selecting Use The touch anything threader threader possibly needle the hook Specialty Shown or using you using embroidery. Threading needle needle a needle a Prop on needle larger OK. OK. a needle cannot through through threader correct if new the cleaning. thread thread page your your the the the due when and so the Correct Correct that threads needle needle will erly threader system thread, as needle will automatic thread needle needle. machine suitable to continue correctly authorized authorized 34. identify may presser the not turning that that not Touch the the something again appear. Thread/Needle Thread/Needle may A threader threader Upper to be 130/705 be needle needle touch eye. completely size is is new has damage for blocking too too threaded. the fails or OK foot. not sewing as needle on or Once shifted pop-up thread selected PFAFF® PFAFF® Thread, described, cancel. thick thick problem to the be eye. eye. may may lighter snagging to H. calibrate caught calibrate the the threader. machine. or the and Remove Touch for for not not from the Try message embroidering. small thread fabric page Combination, Combination, weight retailer retailer the the needle or rethread be be needle see using on correctly its are the OK needle, needle, able able the 35. hook it If Remove and the Changing home is unable thread. during needle this with threader for for to needle the removed, manually. to to thread thread. go the that service. service. pull pull automatic by happens, the the position, further to page page machine, to See the sewing runs the the the and See 37. 37 Maintenance an 207 37. See a Hints, page thread under machine, machine, from page solved. use Motion settings and until up original creative horizontal). the the is thread. thread. in or actual Free the the Needle, Tips side the and spools 35. 35. the for the purchased for flat height only rethread rethread problem increments Combination, page page (vertical fabric than the larger 6D. size use the and and pivot thread Threading for designed small with and Foot H. Changing larger or model. until See in Thread, Thread, proper selected position see area pin, quality this the for tension. holder pin retailer. Spring spool. completely completely to plate. plate. 130/705 slightly for embroidery Upper Upper thread. especially tension Thread/Needle high spool the bobbin Embroidery/Sensormatic spool spool cap increments the the the thread correctly, suitable needle. the bobbin. new thread thread needle thread. needle needle. needle 6A system PFAFF® solved. Dynamic over a thread bobbin from on Correct large bobbins is spool small the the approved the to the the the the the new new a the machine. net the the needle lint a needle in a needle the different decrease 39. needle a only a spool Threading Threading using see thread page Change Change Clean see Change 34. Use Use Selecting Insert Remove Place the authorized Attach Use Check Change bobbins Wind Check Remove Insert spool. icon™ Change Attach If Try Change Lower problem Foot, menu so when the which small too under needle it thread? thread is the or caught slubbed? with selected spool? spool, or get slubs thread? thread? for Stitches the the used? properly? down and thick with of of the the properly? properly? lint? high and needle? damaged? damaged? top eaks top for for eaks embroidering? of down correctly? using correct? too used? blunt? up position thread on Br or machine Br the Uneven hole bobbin needle hole full or are at small small wrong pin slide cap the a the the poor ead ead area wound bobbin has too bent plate too plate you tension tension moving dry? sewing snags spool spool Thr thread Thr thread insert insert insert using a spool? needle bobbin thread needle needle bobbin thread correct fabric thread needle best needle the Seam motion you you you you you become thread the the the the the the the the the the the the the using Is Are has Does Is Is Is Did thread If the Is Is Is Is Is Did Is Did free Did Is Is Is The Bobbin Needle Maintenance helpful and If Have Service The The The Thr The 208 Are Is Has Is Is Did Is Is Has Is Did Is Is Is Is outer under you the the the the the the a the the the still ead correct the you you sewing the Machine Embro Embro Machine your have embroidery free wrong embroidery inner fabric correct bobbin hoop area the to have feed embroidery stabilize thread bring Loops sewing presser motion followed around needle attached embroidery hooped lint teeth problems, hoop presser thread idery idery the the collected will Does your foot? setting machine hoop? ar unit set used? the fabric, attached? machine this properly? built evenly properly? e foot Design Design to not embroidery attached? fabric F contact hoop down? troubleshooting Not orming on? between thread used? up Embro serviced wound? properly? too sufficiently? properly F your has is eed and much Distorted the arm on retailer. ider regularly Puck stabilizer or feed to inserted and the information F move eeds teeth? hoop er Underside It ed by may you freely into free? Irr your are be the egularly local Turn the Remove see Remove Slide into Make or Ensure For The Attach settings Make Correct Use Changing Insert Check into Make Clear exactly Hoop menu Foot, If Attach of authorized using fabric the Threading brush. larger fabric a the the off on increase area needle sure sure sure the a in bobbin correct the you matches proper Thread/Needle the socket. hoop menu. Embroi the the the free small type. fabric the hoops, must around Dynamic that the the 6A use correct needle thread retailer! motion suitable attachment Needle, the winding. presser the feed hoop increments Embroidery/Sensormatic needle the the be in the use embroidery Upper dery the such tightly embroidery completely teeth plate proper hoop. outer connector Spring setting for hoop embroidery page foot. correctly a Combination, selected are and Design Thread, on way hoop. hooped. until stabilizer clips. 34. Foot in the not clean pivot that sewing is and unit the as embroidery set 6D. inserted fabric. page described, unit. the the problem rethread to height is for properly mode. down page inner feed 35. your See Free all in teeth 37. Selecting is hoop the the arm. in see technique settings Motion solved. the attached machine, way with Maintenance 209 maximum 50–60Hz b/g/n 802.11 band stitches/minute lamps 1050 FR5 II 2.4GHz +17dBm -97dBm 14.5 4.1 590 220 400 100–120V/200–240V, <100W LED will can the your guide help sample parts. shows damage or and or that user’s sewing out this A words defect Accessories and unit accessories stitch well. than any notice. a only as and problem. prior cover have that machine the arts not you P machine embroidery non-original information specifications bring If specification without power of does model (kg), (kg), icon™ you. diagnose dimensions: use consumption better sensitivity please speed (mm) (mm) (mm) class voltage by technical module: control with changed give weight weight warranty ative be The echnical Frequency Transmitting Receiver Sewing Foot Safety WiFi Net Net Machine Width Height Length Rated Nominal Light • technician often cre T The Non-Original problem, caused using You have purchased a modern, updatable sewing and embroidery machine. As we regularly release firmware updates, it is possible that there may be some differences between the machine firmware and the firmware described in the user’s guide. Consult your local authorized PFAFF® retailer, and be sure to visit our website at www.pfaff.com for the latest updates of the firmware and the user’s guide. We reserve the right to change the machine equipment and the assortment of accessories without prior notice, or make modifications to the performance or design. Such modifications, however, will always be to the benefit of the user and the product.

INTELLECTUAL PROPERTY CREATIVE, CREATIVE ICON, IDT, MYSEWNET, PFAFF, and PERFECTION STARTS HERE are trademarks of Singer Sourcing Limited LLC.

Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation relating to electrical/ electronic products. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. When replacing old appliances with new ones, the retailer may be legally obligated to take back your old appliance for disposal free of charge. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

Manufacturer VSM GROUP AB, SVP Worldwide Drottninggatan 2, SE-56184, Huskvarna, SWEDEN www .pf aff.com

4710086-26B · © 2017 Singer Sourcing Limited LLC · All rights reserved