Seal Bond® Construction Solutions Seal Bond® 485 Fast Grab Adhesive

Product Description Typical Properties SB 485 is a high-strength, fast curing, elastomeric adhesive for exterior construction and Please contact your Seal Bond Sales Representative before writing specifications around this hardscaping. SB 485 is an environmentally friendly formula that contains no solvents or product. Product properties are as follows: isocyanates and yields very low VOC’s. SB 485 is a low odor and low shrinkage formula that provides non-sag performance for vertical or overhead applications. Property Typical Value Units Test Method

EPA Test Method VOC’s 25 g/L Product Information: Features & Benefits 24

• Fast strength buildup Skinover time @ 50% R.H. 70 deg F 20 Min. ASTM C679 • Excellent vertical adhesive strength • Fast grab minimizes the need for additional fasteners Density 12.67 #/gal • Extremely low shrinkage Hardness 44 Shore A • Indoor/Outdoor use on a variety of substrates • Environmentally friendly, solvent free, low odor and low VOC Lap Shear Green Strength: • Extrudable 5 Minutes 93.6 10 Minutes 93.6 lbf/ft2 Ease of Installation 20 Minutes 93.6 40 Minutes • Easily gunnable 168.48 • Single component high solids formula Extrusion Rate @ 40 PSI 45.6 g/min. • One tube covers approximately 27 linear ft. with a ¼ inch bead depending on substrate conditions (temperature and moisture), substrate porosity Viscosity Spindle 10 RPM 1,912,000 cps and uniformity of application Color Natural • Installation temperature range 30° F (-17.8° C) to a maximum surface temperature 140° F (60° C). Do not install in direct sunlight if Repositionability Up to 15 Min. ambient temperature exceeds 95° F (35° C) Linear ft. Coverage Rate 27 at 1/4” bead

Common Applications Peel Strength: • Vertical Block / Concrete ABS Plastic 19.89 • Interior / Exterior Molding and Trim Acrylic 21.09 Aluminum 22.42 • Cove Base ASTM D903 • Cement Board Glass 20.09 lbf/in. • Vertical Landscape Walls Pine 20.39 • Drywall to wood and metal studs PVC 25.14 Cold Rolled Steel 23.48 • Kitchen Backsplashes Tensile 323 psi ASTM D412 High Performance Durability Elongation at Break 412 % ASTM D412

• SB 485 can be installed on damp surfaces SB 485 typical values represent data from multiple batches. Values will be refreshed, as necessary, • The cured bead exhibits excellent long-term adhesion to the porous surfaces upon data collection from additional campaigns and long-term variability discernment. • Does not dry or become brittle • Low odor, ideal for indoor and outdoor use • Eliminates the need for screws, nails and other mechanical fasteners in most projects • Weather and water resistant

1 Seal Bond® 485

Preparation Equipment To improve adhesion performance make certain that all surfaces are clean and free of A premium Caulking Gun with a minimum 26:1 thrust ratio recommended. dirt, dust, grease, oil, frost and other contaminants. SB 485 should be conditioned to All manufacturer instructions should be followed. room temperature before use. This product can be used at temperatures as low as 30° F. Product can be applied on damp surfaces provided no moisture is transferred to the skin when the substrate is touched. This flexibility reduces substrate preparation and protection requirements.

Application Cut nozzle base on tube and screw on the v-notch applicator tip. Using a caulking gun, apply SB 485 to one of the surfaces in a continuous bead spanning the full width but staying 1/2” from the outside edge. Join substrates in less than 15 minutes and press firmly. Adhesive cures within 24 hours.

Top Packaging SB 485 is available in 9.8 oz. and 28 oz. cartridges. V-Notch Applicator Tip

Bottom 1/2” Warranty Seal Bond warrants that our products are manufactured and conform to strict quality assurance specifications. For warranty information visit: www.seal-bond.com/terms Curing SB 485 skins over and is tack free or dry to touch within 20 minutes at 70°F and 50% relative humidity. Any performance testing should be done after product is fully cured (14 days).

Limitations Clean-up SB 485 should not be used in applications in which it will be permanently exposed to liquid water. Clean tools with mineral spirits, naphtha, citrus-based cleaners, or gel-based paint stripper. Avoid using water for cleanup.

Material Storage/Disposal Store securely between 60° F - 80° F in unopened container. Keep tube tightly sealed. Precautionary Statements Dispose of contents/container in accordance with Local/Regional/National/International Do not use until all instructions and safety precautions have been read and understood. Regulations. Refer to Safety Data Sheet (SDS) for further information. Wear protective gloves, protective clothing and eye protection. Wash contaminated clothing before reuse. Contaminated work clothing should not be allowed out of the workplace. IF ON SKIN: Wash exposed body areas with soap and water. Shelf Life and Storage IF IN EYES: Rinse with water, remove contact lenses and continue rinsing. If exposed or The shelf life is 12 months for an unopened container from the date of manufacture. Store opened concerned get medical advice/attention. Refer to Safety Data Sheet (SDS) for further containers with a plastic protective liner. Before reusing a previously opened container, first remove any information. cured material that may have formed at the top.