PCS400R Pro:Centric ® Server
Installation & Setup Guide Warranty
The latest product information and documentation is available online at:
www.lg.com Copyright © 2017 LG Electronics Inc. All Rights Reserved. Table of contents ENGLISH 3 Warning! Safety instructions 21 PCS400R Configuration Options 21 Network and Communication Setup 6 PCS400R Product Description 22 Log In to the PCS400R and Access the Main Menu 6 Features 23 View System Information 24 Modify Network Settings 7 Setup Information 27 Modify the Server Host Name 7 PCS400R 29 Set the Time Zone 7 Video Channel Assignments for RF Output (QAM-B) 30 Set the Date and Time 8 Video Channel Assignments for RF Output (DVB-C) 30 Change the Login Password 8 Video Channel Assignments for RF Output (ISDB-T) 31 Change the Portal Application 9 Video Channel Assignments for IP Output 32 Monitor the System 9 ASI Output (Optional) 33 Update the PCS400R Operating System 33 Update the VPN Setup 10 Rear and Front Panel Overviews 34 Shut Down the System 10 PCS400R Rear View 34 Reset the System 11 PCS400R Front View 34 Exit the Current Session
12 Rack Installation 35 Troubleshooting 12 Typical Rack Installation 35 PCS400R Setup 13 Rack-mount Considerations 36 PCS400R Communication
14 System Setup 37 Specifications 14 Typical Setup Diagram for PCS400R with ASI Output 15 Typical Setup Diagram for PCS400R with RF Output 39 Open Source Software Notice 16 Typical Setup Diagram for PCS400R with IP Output Information 17 VPN Network Connections Overview 18 Setting Up the Pro:Centric Network 56 LG PCS400R Pro:Centric Server Warranty
• Design and specifications subject to change without prior notice. • This document provides examples of typical command line interface and text-based user interface (TUI) displays. Your displays may vary from those shown in this document. 2 ENGLISH 3 DO NOT OPEN DO NOT CAUTION RISK OF ELECTRIC SHOCK Product can be deformed. Product TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITMES WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES. ALL THIS PRODUCT AT FROM AWAY WITH OPEN FLAMES ITMES OF FIRE,THE SPREAD KEEP CANDLES OR OTHER PREVENT TO - Read these instructions. these instructions. Keep all warnings. Heed all instructions. Follow near water. Do not use this apparatus only with dryClean cloth. instructions. with the manufacturer’s Install in accordance openings. ventilation Do not block any produce (including amplifiers) that or other apparatus stoves, registers, heat radiators, such as sources, heat Do any not install near blades with one wider than the plug has two A polarized plug. or grounding-type the safetyDo purpose of the polarized not defeat it where and the point receptacles, particularly convenience on or pinched, plugs, at being walked from cord the power Protect by the manufacturer. specified Only use attachments/accessories When a cart is by the manufacturer or sold with the apparatus. or table specified bracket, only with the cart, tripod, Use stand, such as way, all servicingRefer has been damaged in any qualified service to when the apparatus Servicing personnel. required is any product with chemicals including glass cleaner, Do not clean your the product. only when cleaning detergent authorized Use heat. your for provided are prong wide blade or the third The prong. grounding blades and a third plug has two A grounding-type other. outlet. of the obsolete replacement consult an electrician for your outlet, fit into plug does not If the provided safety. the apparatus. from exits injury tip-over. avoid from to in order the cart/apparatus use caution when moving combination used, has been the apparatus apparatus, the fallen into liquid has been spilled or objects or plug is damaged, have cord power-supply been dropped. or has normally, does not operate or moisture, rain to exposed which can damage the etc., alcohol benzene, thinner, industrial), abrasive, (car, wax insecticide, lubricants, type of air freshener, product and/ or its panel. - • • • • • • • • • • • • • •
literature accompanying the appliance. accompanying literature of sufficient magnitude to constitute a risk of electric to persons. constitute to shock magnitude of sufficient This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) of important and maintenance alert instructions to operating the presence in the symbol is intended the user to This This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be may that enclosure within the product’s voltage” “dangerous of uninsulated alert to the presence symbol is intended the user to This
Please read these safety precautions carefully before using the product. using the before carefully these safety precautions Please read to help the instruction.example your product because just it is from different be somewhat may the illustration In this manual, has possibility device of electric human safety as the applicable to wireless wave serviceManufacturer cannot and installer related provide interference. WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. TO THIS PRODUCT EXPOSE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT REDUCE TO : WARNING CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER TO TO INSIDE. REFER PARTS NO USER-SERVICEABLE BACK). (OR COVER REMOVE THE RISK OF ELECTRIC SHOCK, DO NOT REDUCE TO : CAUTION SERVICE PERSONNEL. QUALIFIED
• • • Warning! Safety instructions Warning! • Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall. • If water or another substance enters the product (like a AC adapter, power cord, TV), disconnect the power cord and contact the service centre immediately. Otherwise, this may result in fire or electric shock. • Only use an authorized AC adapter and power cord approved by LG Electronics. Otherwise, this may result in fire, electric shock,
ENGLISH malfunction or product deformation. • Never Disassemble the AC adapter or power cord. This may result in fire or electric shock. • Be careful in handling the adapter to prevent any external shocks to it. An external shock may cause damage to the adapter. • Power Sources -- This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your INSTALLATION, consult your product dealer or local power company. • Overloading -- Do not overload wall power outlets and extension cords as this can result in a risk of fire or electric shock. • Disconnect Device -- The AC mains plug is used as the disconnect device. The disconnect device must remain readily operable. • Object and Liquid Entry -- Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Do not use liquid cleaners or aerosol cleaners. • Outdoor Use -- To prevent fire or shock hazards, do not expose this product to rain or moisture. • Wet Location -- Do not use this product near water or moisture or in an area, such as a basement, that might become flooded. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. • Test Equipment -- In some cases, LG has supplied or recommended the use of test equipment and devices for the setup and testing of the equipment. The operation and maintenance of test equipment is described in their associated instruction manuals. Please refer to these manuals for explicit instructions regarding the safe use and handling of the equipment. • Damage Requiring Service Unplug this product from the wall power outlet and refer servicing to qualified service personnel under the following conditions: -- If the power-supply cord or plug is damaged. -- If liquid has been spilled, or objects have fallen into the product. -- If the product has been exposed to rain or water. -- If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. -- If the product has been dropped or the cabinet has been damaged. -- If the product exhibits a distinct change in performance. Refer all servicing to qualified service personnel. • Servicing -- These servicing instructions are for use by qualified service personnel only. To reduce the risk of electrical shock, do not perform any servicing other than that described in the operating instructions unless you are qualified to do so. • Replacement Parts -- When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards.
4 ENGLISH 5 The apparatus with Class I construction must be connected to a mains socket outlet with a protective earthing outlet with a protective connection. a mains socket I construction with Class must be connected to apparatus The Maintain reliable earthing of rack-mounted equipment. Particular attention should be given to supply connections to other than should be given Particular attention equipment. earthing reliable Maintain of rack-mounted Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the overloading and the effect the supply circuit that the connection to to of the equipment be given should Consideration Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment of the equipment operation for safe required of air flow the amount should be such that in a rack of the equipment Installation If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater be greater may environment of the rack temperature ambient the operating assembly, If installed in a closed or multi-unit rack The product can be deformed or fire can break out due to overheating inside the product. overheating to due out can break product or fire can deformed be The required. Ventilation operable. readily plug must remain The Mains plug is the disconnecting device. hazard. cause a fire may This Only qualified service personnel should handle and install this unit. A series of screws with lock washers are used to secure the to secure used washers are with lock Only service qualified A series of screws and install this unit. personnel should handle Upon completion of any service or repairs to this product, ask the service perform to this product, service that technician to of any determine safetyUpon completion to checks repairs or direct connections to the branch circuit (e.g. use of power strips). use of power (e.g. circuit direct connections the branch to circuits might have on overcurrent protection and supply wiring. and supply protection overcurrent on have might circuits is not compromised. To ventilate the system normally and avoid overheating, leave at least 2.5 cm on each side (including top (including top least 2.5 cm on each side at leave overheating, normally and avoid the system ventilate To is not compromised. power AC the unit’s that ensure of the PCS400R. Also, top on the stack other equipment of the PCS400R. Do NOT and bottom) and should ventilation adequate should have adapter Each adapters. power or bundled with other AC stacked is never adapter sources. other heat from be isolated than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with compatible in an environment installing the equipment to should be given consideration Therefore, ambient. than room in this document). by the manufacturer (See information specified specifications (Tma) temperature the maximum ambient top and bottom covers of the unit. Use caution when handling the unit as the lock washers may have rough edges. Do NOT run run Do NOT edges. rough have may caution as the lock washers when handling the unit Use of the unit. covers and bottom top of the unit. covers top and bottom the over fingers your the product is in proper operating condition. operating the product in proper is ------Mains Outlet Earthing Reliable EarthingReliable Circuit Overloading Reduced Air Flow Reduced Elevated Operating Ambient Operating Elevated Wear a properly grounded, antistatic wrist strap to avoid causing electrostatic (ESD) damage to the PCS400R. damage to (ESD) causing electrostatic avoid to wrist strap antistatic grounded, a properly Wear rack. 19-inch equipment a standard slide the PCS400R into Carefully ALL FOUR MOUNTING SCREWS BE USED. MUST hardware. use the appropriate to sure in the rack, make mounting When of the PCS400R. on the top stack other equipment support Do is not designed to NOT equipment other devices. This on the PCS400R connectors. of the cabling is not a strain and supported the weight Rear cabling must be dressed so that UNEVEN TO DUE ACHIEVED A HAZARDOUS IS NOT CONDITION THAT SHOULD BE SUCH THE RACK IN THE EQUIPMENT MOUNTING OF Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions. with the manufacturer’s Install in accordance openings. of the ventilation Do not block any or rack. such as bookcase Do the productinstallation in a built-in not place DEVICEDISCONNECTING FROM MAINS cosmetics or candle. cup, of the product such as flowerpot, liquid on top containing Do anything not place Handling Notice Handling Safety Check - - - - - MECHANICAL LOADING. ------• • • • • • • • • • • • • • • • • Rack-mount Considerations Rack-mount PCS400R Rack Installation (See p. 12, 13) PCS400R Rack (See Installation p. PCS400R Product Description
The LG PCS400R Pro:Centric® server is a stand-alone, remotely-controlled processor and controller for the Pro:Centric system. The server enables ENGLISH you to create and remotely manage portal and application content for LG TVs over ASI, RF, or IP, using either the Pro:Centric Java or Pro:Centric Direct HTML application.
Features • Supports the Pro:Centric Java or Pro:Centric Direct HTML application. • Three output options: ASI, RF, or IP. -- ASI output: The PCS400R generates one channel for GEM data only or multiplexed GEM/site data. -- RF output: QAM-B (6 MHz), DVB-C (6 MHz, 7 MHz, or 8 MHz), and ISDB-T (6 MHz) modulations are supported. The PCS400R generates one 256-QAM or 64-QAM RF channel for GEM/site data. -- IP output: The PCS400R generates two multicast streams for GEM/site data. • Customer may work with content provider to create Pro:Idiom® encrypted content for RF or IP video playout channels. -- QAM-B and DVB-C RF output: In addition to the GEM/site data channel, the PCS400R generates up to seven contiguous RF channels for video playout. Each of these channels supports either two or three programme streams multiplexed on each channel. This capability provides output of up to 21 programmes of video content. -- ISDB-T RF output: In addition to the GEM/site data channel, the PCS400R generates up to one (Java application) or two (HTML application) contiguous RF channels for video playout. Each of these channels supports either two or three programme streams multiplexed on each channel. This capability provides output of up to three (Java application) or six (HTML application) programmes of video content. -- IP output: In addition to two multicast streams for GEM/site data, the PCS400R generates 21 multicast data streams for video playout. Each data stream supports one programme. This capability provides output of up to 21 programmes of video content. • Provides remote management capability over Ethernet. • Small, lightweight chassis. • 19-inch rack-mountable. • 1U height profile to minimize rack space usage.
An Internet browser-based Admin Client graphical user interface (GUI), provided for system integrator (SI) partners and lodging/institution administrators, facilitates support and maintenance of the Pro:Centric system. The Admin Client enables users to remotely manage system backups, output configuration, software updates, portal/information section content, TV configuration settings, etc.
6 ENGLISH 7 (for the (for
Pro:Centric Direct Admin Client User Guide (for the Java application) or the application) the Java (for : Once the PCS400R hardware and software is installed and the initial setup completed, output parameters are configured in the configured are parameters output completed, is installed and the initial setup and software hardware : Once the PCS400R : AC Power Cord and Adapter Cord Power : AC PCS400R Accessories
HTML application), as applicable. application), HTML Pro:Centric Server Admin Client User Guide Note of either the a copy available readily have you that it is recommended with this document, Along Client. Admin Pro:Centric appropriate
Create a channel assignment plan for the installation site, or modify an existing plan to incorporate the RF output of the PCS400R. Ensure that that output of the PCS400R. Ensure the RF incorporate plan to or modify an existing site, the installation for plan a channel assignment Create noise. of existing on the frequency spectrum a location is free Find that Select the location for mounting the PCS400R. Ensure adequate ventilation is available. ventilation adequate Select the PCS400R. Ensure mounting for the location location. in its targeted the PCS400R chassis mount to Obtain the necessary hardware attachment connect to the following also will need You the PCS400R. for access power Plan and install the necessary and AC (Ethernet) cabling and network Unpack the PCS400R Pro:Centric server unit and all accessories. Unpack the PCS400R Pro:Centric up to eight contiguous CATV broadcast channels are allocated for the PCS400R RF output. The PCS400R uses a 256-QAM or 64-QAM modulation modulation or 64-QAM PCS400R uses a 256-QAM The the PCS400R RF output. for allocated channels are broadcast CATV contiguous eight up to 48 MHz of frequency spectrum. approximately occupying thereby format, then are seven) channels (up to and the remaining RF start Client), The setup (in the Admin channel is user-assigned during system if the RF start example, is channel 2, the channel assignment For standards. frequency allocation assigned per EIA-542 STD CATV automatically further tables for frequency allocation as information EIA-542 STD CATV to channels will be 3, 4, 5, 6, 95, 96, and 97. Refer remaining seven required. the RF PCS400R RF output, for channels available eight all allocate to Thus, the PCS400R is 135. RF channel number for highest available The start channel must be set no higher than 128. a PC directly to the PCS400R for system setup purposes: FTDI TTL-USB cable (P/N TTL-232R-5V-AJ). cable (P/N TTL-USB setup purposes: FTDI system the PCS400R for a PC directly to *
• • • • • • Each input programme is limited to one-half or one-third of the output channel bitrates (Mbps), which in turn are dependent on the modulation on the modulation dependent (Mbps), which in turn are one-half to is limited or one-third of the output channel bitrates input programme Each supports modulation Mbps per channel. 26.97 up to supports and 64-QAM modulation Mbps per channel, 38.8 up to 256-QAM format. Video Channel Assignments RF OutputVideo for (QAM-B) PCS400R
Check the following items before you begin the PCS400R installation and setup procedures. installation begin the PCS400R you before items following the Check Setup Information Video Channel Assignments for RF Output (DVB-C) Each input programme is limited to one-half or one-third of the output channel bitrates (Mbps), which in turn are dependent on the modulation format. 256-QAM modulation supports up to 37.27 Mbps (6 MHz bandwidth), 45.05 Mbps (7 MHz bandwidth) or 50.87 Mbps (8 MHz bandwidth)
ENGLISH per channel, and 64-QAM modulation supports up to 27.95 Mbps (6 MHz bandwidth), 33.79 Mbps (7 MHz bandwidth) or 38.15 Mbps (8 MHz bandwidth) per channel. • Create a channel assignment plan for the installation site, or modify an existing plan to incorporate the RF output of the PCS400R. Ensure that up to eight contiguous CATV channel frequencies are allocated for the PCS400R RF output. The PCS400R uses a 256-QAM or 64-QAM modulation format, thereby occupying approximately 48 MHz, 56 MHz, or 64 MHz (depending on channel bandwidth) of frequency spectrum.
The RF start channel frequency is user-assigned, in KHz, during system setup (in the Admin Client), and the remaining channel frequencies (up to seven) are then automatically assigned in accordance with the specified bandwidth. For example, if the RF start channel frequency assignment is 57,000 KHz with a 7 MHz bandwidth, the seven remaining channel frequencies will be 64,000 KHz, 71,000 KHz, 78,000 KHz, 85,000 KHz, 92,000 KHz, 99,000 KHz, and 106,000 KHz.
The highest available RF channel frequency for the PCS400R is 861,000 KHz.
• Find a location on the frequency spectrum that is free of existing noise. Video Channel Assignments for RF Output (ISDB-T) Each input programme is limited to one-half or one-third of the output channel bitrates (Mbps). ISDB-T modulation supports up to 23.23 Mbps (6 MHz bandwidth) per channel. • Create a channel assignment plan for the installation site, or modify an existing plan to incorporate the RF output of the PCS400R. Ensure that up to two (Java application) or three (HTML application) contiguous CATV broadcast channels are allocated for the PCS400R RF output. The PCS400R occupies up to 18 MHz of frequency spectrum.
The RF start channel is user-assigned during system setup (in the Admin Client), and the remaining channels (up to one for the Java application or two for the HTML application) are then automatically assigned in accordance with the 6 MHz bandwidth. For example, if the RF start channel assignment is channel 7 on a server configured for the HTML application, the two remaining channels will be 8 and 9.
The data channel number must be between 7 and 69. Thus, for example, to allocate all three channels available for PCS400R RF output with the HTML application, the RF start channel must be set no higher than 67. * Note: The Pro:Centric server cannot generate channels 13 and 14 simultaneously. If you intend to configure more than one channel, set the data channel number from 7 to 12 (two channels) or 7 to 11 (three channels) or from 14 to 68.
• Find a location on the frequency spectrum that is free of existing noise.
8 ENGLISH 9 : Refer to the IANA IPv4 Multicast Address Space Registry and/or the IANA Service Name and Transport Protocol Port Number Registry Number Port Protocol Registry Space IPv4 the IANA Transport Multicast to IANA Service and/or the Address : Refer Name and
for furtherfor as required. address/port IP information Note
If the system is using ASI output, install the modulator and upconverter that will receive the ASI output signal from the PCS400R. Refer to the to the PCS400R. Refer the ASI output signal from will receive that and upconverter the modulator install is using ASI output, If the system The PCS400R outputs IPv4 multicast streams. Ensure the institution’s IP network and room receivers support IPv4 the multicast receivers and that and room IP network institution’s the Ensure outputs IPv4 PCS400R multicast streams. The that Ensure the IP output of the PCS400R. incorporate to plan an existing or modify site, the installation plan for a channel assignment Create or another unassigned default (1234) can use the system You port (UDP) streams. the multicast data for Protocol Reserve Datagram one User manufacturer’s documentation. manufacturer’s network is capable of selectively routing multicast traffic. Refer to vendor equipment documentation for further documentation equipment vendor information. to Refer multicast traffic. is capable of selectivelynetwork routing the for allocated 239.255.255.255, are 224.0.0.0 to range the designated within IPv4 23 unused and unreserved multicastup to addresses, PCS400R IP output. For incremented. then automatically are channel assignments and the remaining IP startThe Client, in the Admin channel is user-assigned streams the first Since two if the IP start 227.0.0.42, etc. channels will be 227.0.0.41, example, 227.0.0.40, the remaining is channel assignment be 227.0.0.42. will channel in this scenario content first video the data, site for reserved are in use. port conflict with other protocols The must avoid etc. 50,000, 50,001, example, for port number, *
• • • •
ASI output supports up to 19.4 Mbps each for GEM and site data (total of 38.8 Mbps). (total ASI output supports data site GEM and 19.4 Mbps each for up to ASI Output (Optional)
Each IP stream is limited to 19.4 Mbps. 19.4 to limited is IP stream Each Video ChannelIP Output AssignmentsVideo for Rear and Front Panel Overviews
ENGLISH PCS400R Rear View
RF-TAP RF-OUT Feature Port Control Port
ASI-OUT Service Port POWER 19VDC
(0 dBmV)
AC Power Cord & Adapter
• Disconnect Device The AC mains plug is used as the disconnect device. The disconnect device must remain readily operable. • RF TAP Connector Reserved for service technician use only. When not in use, this connector must remain terminated with attached terminator accessory.
10 ENGLISH 11
PWR PWR (POWER LED) PWR (POWER
Ventilation Washers with Lock Screws Air flow must not be obstructed. To ventilate the system normally and avoid overheating, leave at least 2.5 cm on each side leave overheating, avoid and normally the system ventilate To must not be obstructed. flow Air of the PCS400R. top on the stack other equipment of the PCS400R. Do NOT and bottom) (including top secure used to Only are qualified service with lock washers should handle and install the PCS400R. A series of screws personnel Do edges. rough have may caution when handling the unit as the lock washers of the PCS400R. Use covers and bottom the top of the unit. covers and bottom the top over fingers your run NOT • • PCS400R Front View PCS400R Front Rack Installation
ENGLISH Typical Rack Installation
1 To avoid causing electrostatic (ESD) damage to the PCS400R during installation, attach an antistatic wrist strap to a properly grounded rack/ object and put it on. 2 (Optional) As shipped, the PCS400R mounting brackets are attached flush with the front of the unit (See diagram ). If desired, the mounting brackets may be detached from the unit and reattached, for example, so that they are flush with the rear of the unit (See diagram ). If you wish to change the location/orientation of the mounting brackets, carefully remove each of the four (M4 x L10 mm) screws and attendant washers (one flat and one lock washer per screw) holding each bracket in place. Then, use the same screws and washers to reattach the mounting brackets in the desired location. 3 Carefully slide the chassis into a standard 19-inch equipment rack. 4 Use all four mounting screws to secure the chassis to the rack.
(A)
PWR
PWR To rack To rack
(B)
RF-TAP RF-OUT Feature Port Control P ort Service Port ASI-OUT POWER 19 V DC
RF-TAP RF-OUT Feature Port Control P ort Service Port ASI-OUT POWER 19 V DC
Use flat washer and lock washer with each M4 x L10 mm mounting bracket screw.
12 ENGLISH 13 2.5 cm minimum 2.5 cm minimum PWR Front View of Rack Cabinet View Front
If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room than room be greater may environment of the rack temperature ambient the operating assembly, If installed in a closed or multi-unit rack with the maximum ambient compatible in an environment installing the equipment to should be given consideration Therefore, ambient. in this document). by the manufacturer (See information specified specifications (Tma) temperature is not of the equipment operation for safe required of air flow the amount should be such that in a rack of the equipment Installation of the and bottom) top least 2.5 cm on each side (including at leave overheating, normally and avoid the system ventilate To compromised. or stacked is never adapter power AC the unit’s that ensure Also, of the PCS400R unit. on the top stack other equipment PCS400R. Do NOT sources. other heat from and should be isolated ventilation adequate should have adapter Each adapters. power bundled with other AC have might of the circuits overloading and the effect the supply circuit that the connection to to of the equipment be given should Consideration wiring. and supply protection on overcurrent supply connections to other than direct connections should be given Particular attention equipment. earthing reliable Maintain of rack-mounted strips). use of power (e.g., circuit the branch to earthing outlet with a protective connection. a mains socket I construction with Class must be connected to apparatus The
B. Reduced Air Flow Reduced B. C. Circuit Overloading Earthing Reliable D. Mains OutletE. Earthing
A. Elevated Operating Ambient Operating A. Elevated Rack-mount Considerations Rack-mount System Setup
Refer to the following diagrams, and complete the system installation as described on pages 18 to 20. ENGLISH
* Caution: Do NOT make system connections until instructed to do so during the system installation procedure. In some instances, configuration steps must be performed before physical connections are made.
Typical Setup Diagram for PCS400R with ASI Output
Service Port connection
Laptop PC (for installation purposes)
ASI Coaxial Cable (eth0) ASI In QAM Modulator Switch IF Out RF Coaxial Cable
Router IF In DTV Upconverter RF Out RF Cable
Combiner
Internet
RF Distribution System
Laptop PC (for remote management)
Room Receiver
14 ENGLISH 15 Internet Router Switch Laptop PC management) remote (for (eth0) Service connection Port RF Cable
Combiner
Laptop PC purposes) installation (for RF Distribution System Room Receiver Room Typical Setup RF Output with PCS400R Typical Diagram for Typical Setup Diagram for PCS400R with IP Output ENGLISH Service Port connection
Laptop PC (for installation purposes)
(eth1, 1000BaseT [default] (eth0) Full Duplex)
Multicast/IGMPv2 Switch (with Gigabit ports) Switch Internet
Router (Ex: 192.168.1.*/24) Multicast/IGMPv2 Router CAT5E Cable (Ex: 192.168.2.*/24)
(Optional)
Internet Laptop PC (for remote management)
Room Receiver
16 t VPN Clien PC Laptop
ENGLISH 17 ternet In VPN Client PCS400R er rv entric o:C VPN Se Pr VPN Internet/
PC
Laptop VPN Server Pro:Centric VPN Client VPN Network Connections Overview Network VPN Setting Up the Pro:Centric Network This section describes how to complete the initial network configuration for the PCS400R. See also typical setup and VPN network connections diagrams above.
ENGLISH 1 If your system is using ASI output, make the following connections; otherwise, go to step 2. • Connect a 75 ohm BNC-to-BNC coaxial cable between ASI OUT on the PCS400R and ASI IN on the modulator. • Connect an RF coaxial cable between IF OUT on the modulator and IF IN on the upconverter.
* Note : The BNC cable must be less than 9.2 meters in length.
2 To enable remote management, connect one end of a CAT5 RJ-45 Ethernet cable to the Control Port on the PCS400R rear panel, and connect the other end of the cable to the institution’s network. 3 Connect the PCS400R power supply to the POWER connector on the PCS400R rear panel. Then, plug the AC power cord into a powered AC line receptacle. When power is applied, the PWR (Power) LED on the PCS400R front panel will initially flash red and then turn green (blinking during boot-up). The boot-up process for the PCS400R may take several minutes. When boot-up is complete, the PWR LED on the PCS400R front panel will light continuously green. 4 Once the PWR LED is lit continuously (no longer blinking), use the FTDI TTL-232R-5V-AJ cable to connect a PC to the Service Port on the PCS400R rear panel. 5 Using HyperTerminal or an equivalent terminal emulation programme on the PC, configure the serial port as follows: -- Bits per second/baud = 115,200 -- Data bits = 8 -- Parity = None -- Stop bits = 1 -- Flow Control = None * Note: To avoid configuration errors, make sure the keyboard settings on the terminal emulator assign the backspace character to Ctrl + H (ASCII 8). Once the connection is established, you should see a login prompt. (If the login prompt is not automatically displayed, press Enter to refresh the screen.) 6 At the login as: prompt, type admin and press Enter. Then, at the password: prompt, type Password4Partners (case-sensitive) and press Enter.
* Note: After the initial system setup is complete, it is highly recommended that you change the admin user pass- word from its default value. See “Change the Login Password” on page 30 for further information.
The system will display a prompt for you to select the Pro:Centric portal application you will be using:
You must select a portal application to continue. Available portal applications are: 1 pca (Java) 2 pcd (HTML) Enter 1 or 2 to select a portal application:
18 ENGLISH 19 prompt. The The System prompt. prompt. . Enter type setip and press prompt, : If the Control Port network is configured for DHCP but the Control Port IP address is not displayed in the System Information display display Information in the System is not displayed address IP Port but the Control DHCP for is configured network Port : If the Control 26. on pages 24 to Settings” Network “Modify see samples, additional screen and on this step detailed information : For at any PCS400R command prompt to view current menu, if desired. menu, view current to prompt PCS400R command any at Enter can press You : the Command > at Enter type and press info settings, configuration current view the server’s To : : Select the appropriate application based on the purchase order associated with this server. The software license specifies the Java or the Java specifies license software The this server. with associated order on the purchase based application : Select the appropriate (see note above), refer to “Network Setup” troubleshooting information on page 35. If configured, the DHCP server should assign an IP on page 35. If configured, information troubleshooting Setup” “Network to refer above), (see note connects the network. to the PCS400R successfully once Port the Control to address Note Information display will show the IP address that has been assigned to the Control Port (if the network is configured for DHCP) and the out- DHCP) for is configured (if the network Port the Control has been assigned to that the IP address will show display Information further on page 23 for information. Information” System “View See put configuration. Note Note Note HTML application, and the application type must be set accordingly in this step. in this type and the application be set accordingly must application, HTML Note TCP/IP configuration is performed in the CentOS Network Manager TUI (text-based user interface). The system will display the Network Network the will display The system user interface). TUI (text-based Manager Network is performedCentOS configuration in the TCP/IP example: for Manager menu, to select the Java application. select to Enter the Java 1 and press Type select to application. Enter the HTML 2 and press Type * * * * * (Optional) Set a static IP address for the Control Port and/or Feature Port. and/or Feature Port the Control for IP address Set a static (Optional) a) At the Command > a) At When the reboot is complete, you should see a new login prompt. Log back in to the server back in to 6). (See step Log see a new login prompt. should you is complete, reboot the When will see a Command > logged in, you are Once you is used for Port Control The if desired/applicable. Port, Feature and/or Port the Control for IP addresses set static to next describes how step The is using system IP output (not applicable PCS400R if your for is designated Port while the Feature purposes, management/communication remote for DHCP. both ports configured default, RF or ASI output). By are You selected the pcd (HTML) application the pcd (HTML) You selected application run the selected now reboot to System will Once you make your selection, the server will display confirmation before initiating a reboot, for example: for reboot, a initiating selection,before your the server confirmation will display make Once you b) Select/highlight. a connection Enter Edit and press . Enter and press select/highlightc) In the next the port configure screen, wish to you IPv4 xxx.xxx.xxx.xxx/xx, port in the format IP address add the appropriate the selected for port screen Connection on display, the Edit With d) the IP address. mask bits for the network slash) identify the forward digits (after the last two where xxx.xxx.xxx.xxx. and DNS IP addesses in the format add the gateway, Also, Either: • • 9 8 7 * Note: In order to avoid a service interruption, do not modify any of the other fields in the Edit Connection screen. In particular, do NOT modify the data in the Profile Name and Device fields. * Note: The Feature Port IP address MUST be on a different subnet than the Control Port IP address.
ENGLISH e) When you are finished with network configuration for the selected port, select/highlight
10 (Optional) Set the time zone and/or the date and time on the PCS400R. By default, the PCS400R is synchronized with an NTP server and configured for the US Eastern time zone. If the PCS400R is connected to the Internet, the NTP client will periodically update the time setting on the PCS400R. You can set the time zone as required. If the PCS400R is not connected to the Internet, you also have the option to specify date and time data manually. Use the PCS400R “tz” and/or “time” commands (available from the Command > prompt) and follow the system prompts to set the time zone and/or date and time on the PCS400R, as necessary. See “Set the Time Zone” on page 29 and/or “Set the Date and Time” on page 30 for further information. * Note : If you changed the time zone, you will be prompted to reset the system. Continue with step 11.
11 If you made any configuration changes in steps 9 or 10, reset the PCS400R: At theCommand > prompt, type reset and press Enter. The reset process may take several minutes, after which the PCS400R resumes normal operation. 12 Make the appropriate connection to the RF distribution system or IP distribution network depending on the PCS400R output option to be used: • ASI output: Connect the RF output on the upconverter to the RF distribution center combiner, and balance the RF signal so that the Pro:Centric signal level at the TV(s) is between 0 to +7 dBmV. • RF output: Connect RF OUT on the PCS400R to the RF distribution center combiner, and balance the RF signal so that the Pro:Centric signal level at the TV(s) is between 0 to +7 dBmV. • IP output: Connect a CAT5E or better Ethernet cable between the Feature Port on the PCS400R rear panel and the institution’s IP distribution network. • Caution: (ASI/RF Output only) For proper system performance, the Pro:Centric signal level at the TV input (ANTENNA IN) must be between 0 to +7 dBmV. Note that additional equipment may be required to adjust the signal level. • Caution: When not in use, the RF TAP (0 dBmV) connector must remain terminated with attached terminator accessory. The remainder of the system setup—configuration of ASI, RF, or IP output parameters, video playout settings, Pro:Centric Channel Map, etc.—is performed in the Admin Client that is appropriate for your system (based on your selection in step 7 of the procedure above). Refer to either the Pro:Centric Server Admin Client User Guide (Java application) or the Pro:Centric Direct Admin Client User Guide (HTML application), as applicable, for further information. * Note : By default, the server output is enabled for 256-QAM-B modulation (RF output), with the data channel set to 75.
20 ENGLISH 21 Note: Before you proceed with any additional configuration, the PCS400R software should be installed and config- should be installed software the PCS400R configuration, additional with any proceed you Before Note: 20. 18 to on pages described in the setup procedure as ured * : If you want to connect a PC directly to the PCS400R Control Port using an Ethernet CAT5E cable, in order for communication to be to communication for in order cable, CAT5E using an Ethernet Port connectPCS400R Control the to a PC directly to want : If you : To avoid configuration errors, make sure the keyboard settings on the terminal emulator assign the backspace character to Ctrl + H character to assign the backspace emulator settings on the terminal the keyboard sure make errors, configuration avoid To : Bits per second/baud = 115,200 Bits per second/baud bits = 8 Data = None Parity bits = 1 Stop = None Control Flow established, the PCS400R’s IP address must be on the same subnet as the PC’s IP address. must be on the same subnet as the PC’s IP address the PCS400R’s established, Note (ASCII 8). (ASCII Note ------
Use an SSH client to communicate with the PCS400R via a command line interface. If necessary, consult the network administrator to obtain the to administrator the network consult If necessary, line interface. with the PCS400R via a command communicate to an SSH client Use Plug the USB TTL-232R-5V-AJ). cable (P/N TTL-USB establish a direct connection connect the PCS400R, using the FTDI the PCS400R to a PC to To * * IP address that has been assigned to/configured for the PCS400R’s Control Port. Control PCS400R’s for the assigned to/configured has been that IP address the Service Plug the other end of the cable into jack Port driver. device install the an open USB port PC. If necessary, end of the cable into on your panel. on the PCS400R rear the serial port PC, configure on the follows: as programme emulation terminal or an equivalent HyperTerminal Using
• • You will need to know the “admin” user password in order to log in to the command line interface. The default admin user password is default admin user password The line interface. the command log in to to in order user password “admin” the know will need to You the system consult its default value, has been changed from if the password example, for If necessary, (case-sensitive). “Password4Partners” admin user password. obtain the current to administrator There are two typical options for communicating with the PCS400R: typical two communicating options for are There Also note that configuration updates periodically require that you reset the PCS400R. Make sure to reset the unit when directed to do so. the unit when directed reset to sure PCS400R. Make reset the you that require periodically updates configuration that note Also This section describes PCS400R communication options for configuration purposes. configuration section options for This describes PCS400R communication Network and Communication Setup and Network PCS400R Configuration Options Configuration PCS400R Log In to the PCS400R and Access the Main Menu
* Note : The PCS400R must be connected to an IP network for SSH client access. For direct access to the PCS400R Service Port, use the FTDI TTL-USB cable (P/N TTL-232R-5V-AJ). See also “Network and Communication Setup” above for further information. ENGLISH 1 Establish communication with the PCS400R using an SSH client or via a direct connection to the PCS400R Service Port. Once communication is established, you should see a login prompt. (If the login prompt is not automatically displayed, press Enter to refresh the screen.) 2 At the login as: prompt, type admin and press Enter. 3 At the Password: prompt, type the admin password and press Enter. 4 At the Command > prompt, either: • Press Enter to display the PCS400R Main Menu (See example below). • Type the desired command and press Enter. The following sections describe each of the configuration commands. * Note: You can always press Enter at the Command > prompt to display the PCS400R Main Menu.
Example: PCS400R Main Menu
Main Menu
info System information setip TCP/IP Setup Menu tz Timezone setup time Time setup pwd Change password portal Select the portal application monitor System monitor shut Shutdown the system reset System Reset exit End the session Command >
22 ENGLISH 23 601-12480013 1 802 116 PCS400v2 000002703544 Linux 3.10.0-327.e17.x86_64 22:10:57 UTC 2015 #1 SMP Thu Nov 19 00:13:95:21:a2:7d 10.1.2.3 00:0C:63:40:47:db 192.168.20.120 n/a MSps, ASI: 38.81 Mbps Mode 3, 256-QAM-B, RF: 6 MHz, 5.36 75 1 Tue Apr 25 14:42:02 EDT 2017 . Enter type and press info prompt, : If RF output is configured for DVB-C modulation, the display will identify the RF frequency (in KHz) in place of the RF channel. If IP the RF frequency of the RF channel. (in KHz) will identify in place the display modulation, DVB-C for : If RF output is configured Note of the RF fields. in place the multicast IP address will identify the display output is configured,
* Log in to the PCS400R as described on the previous page. previous described on the the PCS400R as in to Log > the Command At
Local time: Channels: RF channel: RF config: VPN IP: Feat IP: Feat MAC: Ctrl IP: Ctrl MAC: OS release: OS version: CPU SN: BIOS vendor: BIOS version: FPGA version: Hardware ID: SN: It is recommended that you record this information for future reference. If you find it necessary serviceto If you call customer or engineering support, reference. future for this information record you that It is recommended available. this information please have Copyright (c) 2017 LG Electronics U.S.A., Inc. U.S.A., (c) 2017 LG Electronics Copyright PCS400R Pro:Centric Server v1.2.1 Server PCS400R Pro:Centric The System Information display identifies important information about the PCS400R, including the unit serial number, hardware ID (firmware ID (firmware hardware important including the unit serial number, about the PCS400R, identifies display information Information System The example: for addresses, and IP addresses, MAC versions, software version),
1 2 View System Information System View Modify Network Settings This section describes how to modify the network settings of the PCS400R Ethernet ports. The Control Port is used for remote management/ communication purposes, while the Feature Port is designated for PCS400R IP output.
ENGLISH 1 Log in to the PCS400R as described on the previous page. 2 At the Command > prompt, type setip and press Enter. The system will display the Network Manager menu. 3 Select/highlight Edit a connection and press Enter to modify the IP configuration of either the Control Port or the Feature Port. * Note : To exit the Network Manager and return to the Main Menu prompt without modifying any settings, select Quit. * Note : You may also modify the server’s host name from the Network Manager. See “Modify the Server Host Name” on pages 27 to 28 for further information.
4 In the next screen, select/highlight the port profile to modify, and then press Enter.
24 ENGLISH 25 Note: Steps 5 to 9 identify all fields that may require modification for the purposes of the Pro:Centric network. In network. purposes of the Pro:Centric the modification for require may 9 identify all fields that to 5 Steps Note: Connection a serviceEdit of the other fields in the In partic screen. do not modify any interruption, - avoid to order fields. and Device Name in the Profile modify the data do NOT ular, * , go to step 9. step , go to selected Automatic If you 7. with step selected Manual , continue If you to view to Enter press field and of the IP Configuration the right select/highlight at
* Note : If you do not specify the network mask bits in the port’s IP address, as indicated above, the system will not create a local route over the network interface (unless the interface is used as the system’s default route).
• Select/highlight
* Note: The Feature Port IP address MUST be on a different subnet than the Control Port IP address.
9 (Recommended) Change the port configuration for IPv6 from Automatic to Ignore: Select/highlight the IPv6 Configuration field and press Enter. Then, select Ignore from the drop-down list of options. 10 When you are finished, select/highlight
26 ENGLISH 27 . Enter type setip and press prompt, : To exit the Network Manager and return to the Main Menu prompt without modifying any settings, select settings, Quit without modifying any . the Main Menu prompt to Manager and return the Network exit To : on Settings” Network “Modify See Manager. the Network from configuration Port and/or Feature also modify the Control may You : Note Note further 25 for pages 24 to information.
* * . Select/highlight Enter hostname and press Set system special or using spaces (avoid Modify the host name as required host name. the current shows field in the Set screen Hostname Hostname The . Enter then press and such as ?, -, etc.) characters, Log in to the server in to 22. described on page as Log the Command > At example: for menu, Manager the Network will display system The
4 3 2 1 This option enables you modify the PCS400R host name. PCS400R host modify the enables you option This Modify the Server the Modify Name Host 5 At the prompt for confirmation, press Enter. ENGLISH
6 If you changed the host name, you will need to reset the system. If you are ready to reset the system immediately, at the Command > prompt, type reset and press Enter (See “Reset the System” on page 34 for further information). * Note: If you intend to modify additional configuration settings during the current session, you may wait until all changes are complete before you reset the system.
28 ENGLISH 29 (See “Reset the System” on page “Reset the System” (See Enter and press type reset prompt, prompt without changing the current time zone. without changing the current prompt . Enter type tz and press prompt, : If you intend to modify additional configuration settings during the current session, you may wait until all changes are complete complete all changes are until wait may session, you settings during the current modify additional configuration to intend : If you United States Central Time before you reset the system. reset you before Note
Therefore TZ=’America/Chicago’ will be used. Therefore TZ=’America/Chicago’ will CDT 2017. Local time is now: Mon Jul 10 16:23:10 22:23:10 UTC 2017. Universal Time is now: Mon Jul 10 Is the above information OK? 1) Yes 2) No #? The following information has been given: The following information has been if the information in the display is correct. The system will confirm the setting and then prompt you to reset the to you the setting and then prompt will confirm system The is correct. in the display if the information Enter 1 and press Type 4). step from this procedure (Repeat zone the time and reset prompt the initial location to return to Enter 2 and press Type Command > the Main Menu Command to return to Enter n and press Type 4. with step continue Then, zone. change the time to Enter y and press Type PCS400R: the board. Time zone has been set. Please reset 8. with step Continue * If you are ready to reset the system immediately, at the Command > at immediately, the system reset to ready are If you further34 for information). Either: The system will display the following prompt for a location, followed by a list of options: by followed a location, for prompt the following will display system The can be set correctly. location so that time zone rules Please identify a or ocean. Please select a continent . Enter and then press location, your option for the appropriate to type corresponds number that the the #? prompt, At a list of options: by followed a country, for prompt the following will display system The Please select a country. . Enter and then press country, your option for the appropriate to type corresponds number that the the #? prompt, At a list of options: by followed a region, for prompt the following will display system The of the following time zone regions. Please select one . Enter and then press region, your option for the appropriate to type corresponds number that the the #? prompt, At example: for confirmation, selections for location an overview and prompts of your displays the system region, specify the time zone you After The system displays the current time zone information for the PCS400R and prompts you to specify whether or not you wish to change the time change wish to specify whether or not you to you and prompts the PCS400R for information time zone current the displays system The zone. York zone is: America/New Current time time zone? [y/n]: Change the Either: Log in to the PCS400R as described on page 22. described on page the PCS400R as in to Log > the Command At
• • • • 8 7 5 6 4 3
1 2 Set the TimeSet Zone the Set the Date and Time By default, the PCS400R is synchronized with an NTP server and configured for the US Eastern time zone. If the PCS400R is connected to the Internet, the NTP client will periodically update the time setting on the PCS400R. If the PCS400R is not connected to the Internet, you also have the option to
ENGLISH specify date and time data manually. Refer to “Set the Time Zone” above for information on setting the time zone. 1 Log in to the PCS400R as described on page 22. 2 At the Command > prompt, type time and press Enter. The system will display the current time (for example: Current time: 2017-06-15 15:45:44) and then initiate a series of prompts to enable you to set the time. 3 At each of the following prompts, type the year, month, and day, respectively. Note that all three of these fields require numerical values. Press Enter after each entry. If applicable, you can also press Enter at each prompt to accept the default value in square brackets. Enter new year [2017]> Enter new month [6]> Enter new day [15]> 4 At each of the following prompts, type the hour and minute, respectively. Note that the hour should be entered in 24-hour format. Press Enter after each entry. If applicable, you can also press Enter at each prompt to accept the default value in square brackets. Enter new hour (0-23) [15]> Enter new minute [45]> Once you enter the minute value, the system will display the new time and then prompt for confirmation, for example: New time: 2017-06-15 15:46:00 Apply? [y/n]: 5 Either: • Type y and press Enter to apply the new time configuration. The system will display confirmation, for example:New time is set • Type n and press Enter to return to the Command > prompt without changing the time configuration. Change the Login Password For security purposes, it is recommended that the admin user login password be unique to the system. Note that the login password is case-sensitive. 1 Log in to the PCS400R as described on page 22. 2 At the Command > prompt, type pwd and press Enter. The system prompts for the current admin user password: Changing password for admin Old password: 3 Type the current password and press Enter. The system will then prompt you to type and retype the new password: New password: Retype password: 4 Type and then retype the new password at the prompts. Press Enter after each entry.
Once you complete the Password fields successfully, the system displays confirmation: Password for admin changed by admin.
30 ENGLISH 31 (HTML (HTML Pro:Centric Direct Admin Client User Guide (Java application) or the application) (Java prompt, type. portal Enter prompt, and press Caution: When your Admin Client portal configuration activities are complete, you must reset the server acti must reset Client to Admin portal you activities- When your configuration Caution: complete, are application configuration. the new vate Caution: This option will create a temporary system interruption and should be used only when necessary. After After and should be used only a temporary necessary. when interruption system create option will This Caution: Admin perform must you appropriate in the of additional steps a number below, the procedure complete you portal- Software application) for fea in order the new Client functionality the Admin for Client (i.e., be initiated. to and portal not ported are output configuration, the other. one application from to configuration licensing, ture : If you intend to modify additional configuration settings during the current session, you may wait until all changes are complete complete all changes are until wait may session, you settings during the current modify additional configuration to intend : If you : Select the appropriate application based on the purchase order associated with this server. The software license specifies the Java or specifies the Java license software The with this server. associated order based on the purchase application : Select the appropriate * * Pro:Centric Server Admin Client User Guide 1) pca (Java) 2) pcd (HTML) before you reset the system. reset you before Note HTML application, and the application type and the application must be set accordingly. application, HTML Note Select a new portal application [2]: Select a new portal Available portal applications are: Available portal
to initiate an immediate reset of the PCS400R. The reset process may take several minutes, after which the system which the system after minutes, several take may process reset The of the PCS400R. reset an immediate initiate to Enter y and press Type must eventually you that note time; however, the current at the system the Main Menu without resetting to return to Enter n and press Type to select the Java application. select to Enter the Java 1 and press Type select to application. Enter the HTML 2 and press Type to return to the Main Menu without changing the portal to return application. to Enter n and press Type to continue. The system will display the available applications, followed by a prompt for a selection: for a prompt by followed applications, the available will display system The continue. to Enter y and press Type resumes normal operation. resumes reset to ready you are on page 34 when System” “Reset the apply the new portalSee to configuration. in order application the system reset the system. * * Continue with step 4. with step Continue Once you make your selection, the server will display confirmation and prompt you to reboot the system, for example: for reboot the system, to you selection, and prompt your the server confirmation will display make Once you application Successfully set to pca (Java) portal You must reset the system now. system? [y/n]: Are you sure you want to reset the Either: At the prompt to select to portal a new the prompt either: At application, Log in to the PCS400R as described on page 22. the PCS400R as described in to Log the Command > At The system prompts for confirmation that you wish to make a change, for example: for a change, make to you wish that confirmation for prompts system The application. to use the pcd (HTML) portal The system is configured the portal appliction? [y/n]: Do you wish to change Either:
• • • • • • The remainder of the new portal application setup—configuration of feature set, output parameters, video playout settings, Pro:Centric Channel Pro:Centric settings, video playout output parameters, of the new portal set, remainder setup—configuration application feature The of the beginning of this section. at Refer as indicated Client, Admin performed etc.—is in the appropriate portal menus, customized interactive Map, either the to 5 application), as applicable, for further for as applicable, application), information.
This option enables you to change the portal change if necessary. or HTML), to (Java enables you option application This Change Application Portal the 4 1 2 3 Monitor the System This option enables you to view dynamic system streaming data. 1 Log in to the PCS400R as described on page 22. ENGLISH 2 At the Command > prompt, type monitor and press Enter to display the current system data. See example on following page. 3 The system data will refresh every second. When you are finished monitoring streaming data, press Enter to stop the system monitor and return to the Command > prompt.
The system monitor display shows streaming data for each of the active video programmes. The first column in the display shows the channel slot numbers for which video playlists can be defined. Slots 1 and 2 are reserved for GEM/site data and Slot 3 is unused (and is not shown in the display). On servers configured with the Pro:Centric Java application, it is possible to add a site video to Slot 2, and so for these systems, Slot 2 will appear in the system monitor display. On the other hand, it is not possible to add a site video to Slot 2 on servers that are configured with the Pro:Centric Direct HTML application, and so for these systems, Slot 2 will not appear in the system monitor display. The system monitor example on the following page shows data for a system that is configured for QAM-B RF output with the Pro:Centric Direct HTML application. * Note: Output parameters are configured in the Admin Client. Refer to either the Pro:Centric Server Admin Client User Guide (Java application) or the Pro:Centric Direct Admin Client User Guide (HTML application), as applicable, for further information.
Example: System Monitor Display (QAM-B RF Output, HTML Application)
SYSTEM MONITOR
Date: 2017-07-12 16:44:27 SN: 401-12080008 Version: 1.1 Output: RF_QAM256_6M Pg/RF: 2 Bitrates (Mbps): Slot Content Secs Mbit Pct RF Out 1 GEM Data 685 8.9 - 75-1 4 Video1.ts 6 5.1 1 76-1 :) 5 Video2.trp 205 4.6 78 76-2 :) 7 Video3.ts 40 4.2 12 77-1 :) 8 Video4.trp 172 2.7 66 77-2 :) 10 Video5.ts 12 3.5 3 78-1 :) 11 - 0.0 - 78-2 13 Video6.ts 171 4.7 94 79-1 :) 14 - 0.0 - 79-2 16 - 0.0 - 80-1 17 - 0.0 - 80-2 19 - 0.0 - 81-1 20 - 0.0 - 81-2 22 - 0.0 - 82-1 23 - 0.0 - 82-2
Press
32 ENGLISH 33 prompt, transfer the new VPN client file using Xmodem Xmodem file using VPN client the new transfer prompt, . Enter press filename and type update software in the prompt, . Enter type and press vpn prompt, . Enter and press type update prompt, - inter may Doing so is in progress. update software while a menu sessions simultaneous initiate Caution: Do NOT and/or cause cease normal configuration PCS400R to the system corrupt the with the active may and process fere operation. *
Send VPN client file using Xmodem ... the Send VPN client At Log in to the PCS400R as described on page 22. in to Log the Command > At filename or select enter the appropriate window, In the Send File and then Send File.... select Transfer in HyperTerminal, example, For protocol. field. and select field, Xmodem in the Protocol in the Filename process. update of the as the result messages as well progress will display system The minutes. several take may process update The further on page 34 for information). “Reset the System” (See the system reset completed, is successfully the update When The system will initiate the download and confirm progress, for example: for progress, and confirm the download will initiate system The pcs400r_app_xxxx.upd Downloading file: further 34 for on page information). “Reset the System” (See system the reset completed, is successfully the update When Enter update filename : the Enter update filename At Log in to the PCS400R as described on page 22. the PCS400R as described in to Log the Command > At
3 1 2 4 The appropriate update file must be provided by LG; the system will not transfer an improper file. an improper not transfer will LG; the system by must be provided file update appropriate The This option is only applicable for the Java portal application. It enables you to update the VPN client via a serial link to the PCS400R. via a serial link to VPN client the update portal to you It enables the Java option is only applicable for application. This Update the VPN SetupVPN the Update
This option is only applicable for the Java portal application. It enables you to update the PCS400R operating system via the Ethernet. via the Ethernet. system operating the PCS400R update portal to It enables you the Java is only applicable option for application. This Update the PCS400R Operating System Operating PCS400R the Update 4 3 2 1 The appropriate update file must be provided by LG; the system will not download an improper file. file. an improper will not download LG; the system by file must be provided update appropriate The Shut Down the System This command allows you to shut down the system in an orderly manner. Use this command to shut down the PCS400R, for example, if you intend to physically move the unit from one location to another. It is also recommended that you run this command from the PCS400R Service Port in order to
ENGLISH track detailed shutdown log messages. * Note: Once you use this command, you must remove power from (i.e., unplug) the unit and then plug the AC power cord back into a pow- ered AC line receptacle when you are ready to restart the server. It is not possible to restart the server remotely. 1 Log in to the PCS400R as described on page 22. 2 At the Command > prompt, type shut and press Enter. The system will prompt for confirmation: Are you sure you want to shut down the system? [y/n]: 3 Either: • Type y and press Enter to shut down the system immediately. The shutdown typically takes about a minute. When the PCS400R is in its shutdown state, the front panel LED will blink steadily green. • Type n and press Enter to return to the Main Menu without shutting down the system. Reset the System
1 If not already logged in, log in to the PCS400R as described on page 22. 2 At the Command > prompt, type reset and press Enter. The system will prompt for confirmation: Are you sure you want to reset the system? [y/n]: 3 Either: • Type y and press Enter to initiate an immediate reset of the PCS400R. The reset process may take several minutes, after which the system resumes normal operation. • Type n and press Enter to return to the Main Menu without resetting the system. Exit the Current Session
At the Command > prompt, type exit and press Enter to end the current session.
34 ENGLISH 35 : When power is first applied to the PCS400R, the PWR LED initially flashes red and then turns green (blinking during boot-up). (blinking and then turns green the PCS400R, the PWR LED initially flashes red is first applied to power When : Note
Make sure all connectors and connections are tight and secure on all entertainment system components. on all entertainment system and secure tight all connectors and connections are sure Make LED the PWR (Power) normally, operating and when the PCS400R is booted i.e., conditions, operating Under standard LED. the PCS400R Check on the PCS400R front panel is continuously lit green. If there is a hardware fault, the PWR LED will turn and stay red. the PWR LED will turn and stay fault, is a hardware If there lit green. panel is continuously on the PCS400R front * Check the Control Port connector on the rear panel of the PCS400R. Make sure the cable connection and secure. is tight sure panel of the PCS400R. Make connector on the rear Port the Control Check the network, the LED will be lit continuously. Once the PCS400R is connected to Port. Observe LED on the Control the green properly. the DHCP server and check that is working status the network verify to administrator the network Contact
• • 1 2 3 If the network is configured for DHCP but the PCS400R has not been assigned an IP address, i.e., the Ctrl IP field in the PCS400R System Information Information System in the PCS400R the Ctrl IP field i.e., address, for DHCP but the PCS400R has not been assigned an IP is configured If the network is blank: display Network Setup Network Equipment Setup Review Equipment The following sections provide basic troubleshooting information for the PCS400R. for information basic troubleshooting sections following provide The PCS400R Setup Troubleshooting PCS400R Communication If you are unable to establish remote communication with the PCS400R, refer to the following flow chart. ENGLISH Cannot Communicate with PCS400R
To verify the PCS400R IP address: • If DHCP is enabled, check the router for DHCP IP address assignments to determine whether the proper IP address is being Check that the proper IP address for the used to communicate with the PCS400R. PCS400R is being targeted. If necessary, adjust • If DHCP is not enabled, connect a PC to the PCS400R Service Port, and then reattempt communication. display the System Information, and ensure the IP address shown in the Ctrl IP field is the IP address being used to communicate with the PCS400R. If necessary, update the Control Port configuration as described in this document.
Yes Problem solved? End
No
Ensure your PC’s IP address is on the same subnet as the PCS400R’s IP address. * Note: For example, if the PCS400R is configured with IP address: If necessary, adjust and then reattempt 192.168.1.x and Network mask: 255.255.255.0, the PC’s IP communication. address cannot be: 192.168.2.x.
Yes Problem solved? End
No
Contact LG.
36 ENGLISH 37 -20° to 70° Celsius -20° to 95% non-condensing -4° to 158° Fahrenheit -4° to 800 mv ±5 ppm 75 Ohms 75 ‘F’ Ohm, Type 54 MHz to 865 MHz 54 MHz to +19 V DC @ 2.2 Amps +19 VHF/UHF 54 - 865 MHz 10/100/1000BaseT, RJ-45 10/100/1000BaseT, -1 dBm (+47.75 dBmV) Typical -1 dBm (+47.75 dBmV) Typical -47.75 dBm (+1 dBmV) 100/1000BaseT Full Duplex, RJ-45 Full 100/1000BaseT Environmental Storage Conditions Storage Environmental Humidity Temperature Up to 8 Contiguous Channels (typically Channels 48 – 64 MHz) 8 Contiguous Up to 215.9 mm 42.977 mm 2.56 kg (rack-only weight) (rack-only 2.56 kg Electrical 482.6 mm (for EIA standard 19-inch rack mount) rack 19-inch standard EIA 482.6 mm (for Dimensions 0° to 40° Celsius 0° to 95% non-condensing 32° to 104° Fahrenheit 32° to DC Input Frequency RF Output Span Test Output Level Test Frequency Accuracy Frequency Level at ASI Out jack at Level RF Out Connectors (2)* RF Out Connectors Impedance at ASI Out jack at Impedance RF Output Range Frequency Ethernet Connector (Control Port) (Control Connector Ethernet Ethernet Connector (Feature Port) (Feature Connector Ethernet Active Output Level at RF Out jacks at OutputActive Level Environmental Operating Conditions Operating Environmental Width Depth Height Weight : Design subject and specifications change without prior notice. to Humidity
Temperature (Tma) Temperature Note *
RF TAP connector reserved for service for connector reserved use only. technician TAP RF Specifications * Modulation Specifications Standard ITU-T J.83 Annex B (QAM-B) Constellations 64-QAM, 256-QAM ENGLISH 64-QAM 5.056941 MBaud Symbol Rate 256-QAM 5.360537 MBaud Interleaving Fixed I = 128, J = 1
Standard EN 300 429 V1.2.1 (DVB-C) Constellations 64-QAM, 256-QAM 64-QAM / 256-QAM 5.056 MBaud Symbol Rate 64-QAM / 256-QAM 6.111 MBaud 64-QAM / 256-QAM 6.9 MBaud
Standard ABNT NBR 15601:2007 (ISDB-T) Parameters 64-QAM, 7/8 Convolutional Code, 1/32 Guard Interval Ratio, 2K FFT, 13 Segments Symbol Rate 8.126984 Ms/s
AC/DC Adapter Manufacturer APD Model DA-65G19 Input AC 100 - 240 V ~ 50/60 Hz Output DC 19 V 3.42 A
38 ENGLISH 39 Copyright PCS400R Pro:Centric Server Pro:Centric Copyright (c) 2014 ABRT team 2014 ABRT (c) Copyright Inc. Foundation, Software 2015 Free (c) Copyright Jaroslav Bagnara
Product Type
Warning: The PCS400R is intended for Commercial use only. It is not a Consumer product It is not a Consumer should not be and use only. Commercial for PCS400R is intended The Warning: dwellings. installed in residential Model Number / Range Model Number Open Source *
abrt 2.1.11 abrt-addon-ccpp 2.1.11 abrt-addon-kerneloops 2.1.11 abrt-addon-pstoreoops 2.1.11 abrt-addon-python 2.1.11 abrt-addon-vmcore 2.1.11 2.1.11 abrt-addon-xorg abrt-cli 2.1.11 abrt-console-notification 2.1.11 abrt-dbus 2.1.11 abrt-libs 2.1.11 abrt-python 2.1.11 abrt-retrace-client 2.1.11 abrt-tui 2.1.11 acl 2.2.51 1.0.28 alsa-firmware alsa-lib 1.0.28 1.0.28 alsa-tools-firmware 3.1.13 at 2.14.0 atk 2.4.46 attr 2.4.46 attr-libattr audit 2.4.1 augeas 1.4.0 Open Source Software Notice Information SoftwareOpen Notice Source Those products identified by the Product Type and Model Range above from LG Electronics, Inc. (“LGE”) contain the open source software detailed software open source the contain (“LGE”) Inc. Electronics, LG from Type and Model Range above Product by the products identified Those use. of their and conditions the terms for licences open source the indicated to Please refer below. Open Source License Copyright authconfig 6.2.8 GPL-2.0 Copyright (c) 1999-2014 Red Hat, Inc. autogen 5.18 LGPL-3.0 ENGLISH avahi 0.6.31 LGPL-2.1 bash 4.2.46 GPL-3.0 Copyright (c) 2007, 2009, 2011, 2014 Free Software Foundation, Inc. bash-completion 2.1 GPL-2.0 bc 1.06.95 GPL-2.0 Copyright (c) 1998, 2001, 2003, 2014 Free Software Foundation, Inc. binutils 2.23.52.0.1 GPL-3.0 Copyright (c) 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009 Free Software Foundation, Inc. biosdevname 0.6.2 GPL-2.0 Copyright (c) 2006 Dell, Inc. by Matt Domsch
40 ENGLISH 41 Copyright Copyright (c) 1992, 1993, 1994, 1995, 1996, 1998, 2001, 2002 Free Software Software Free 1998, 2001, 2002 1995, 1996, 1992, 1993, 1994, (c) Copyright Inc. Foundation, Ltd Canonical 2004-2015 (c) Copyright 2005, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, Copyright Ts’o Theodore 2006, 2007, 2008, 2009, 2010 by Neuling & Michael Russell J. ‘Rusty’ 1999 Paul (c) Copyright 2001-2002 Bart (c) De SchuymerCopyright Inc. Foundation, Software 2015 Free (c) Copyright S. Miller ([email protected]) 1998 David (c) Copyright 2001 Sun Microsystems Copyright Portions 2001 Jeff Garzik
42 ENGLISH 43 Copyright Copyright (c) 2003-2011 by the gtk2-perl team the gtk2-perl 2003-2011 by (c) Copyright Software 2009-2016 Free 2006-2007, 1999, 2001-2002, (c) Copyright Inc. Foundation, Jean-loup Gailly 1992-1993 (c) Copyright
44 ENGLISH 45 Copyright Copyright (c) 2000-2002, 2007, 2008 Red Hat, Inc. 2007, 2008 Red Hat, 2000-2002, (c) Copyright Looijaard Frodo (c) Copyright Merlin Hughes (c) Copyright Bob Schlaermann (c) Copyright Mark M. Hoffman (c) Copyright Jean Delvare (c) Copyright Gilbert 2002-2004 D. (c) Copyright Inc. 2008,2009 Red Hat, (c) Copyright 2017 MariaDB (c) Copyright 2017 MariaDB (c) Copyright 2017 MariaDB (c) Copyright Electronics 2012, 2013 Zenith/LG (c) Copyright Kleen 1997,1999, 2000 Andi (c) Copyright Morrison (VE7JPM) 1994 John Paul (c) Copyright License LGPL-2.1 LGPL-2.1 LGPL-2.1 GPL-2.0 GPL-2.0 GPL-2.0 LGPL-2.1 GPL-2.0 GPL-2.0 GPL-2.0 LGPL-2.1 LGPL-2.1 GPL-2.0 GPL-3.0 GPL-2.0 GPL-2.0 GPL-2.0 GPL-2.0 GPL-2.0 GPL-2.0 GPL-2.0 GPL-2.0 GPL-2.0 MPL-2.0 GPL-2.0 GPL-2.0 GPL-2.0 LGPL-2.1 GPL-2.0 LGPL-2.1 LGPL-2.1 MPL-2.0 MPL-2.0 MPL-2.0 MPL-2.0 Open Source libusbx 1.0.15 1.0.15 libusbx libuser 0.60 1.1.6 libutempter 0.2.8.4 libwmf 3.10.0 Linux Kernel lksctp-tools 1.0.13 lmsensors 3.3.4 3.8.6 logrotate lsscsi 0.27 lvm2 2.02.130 lvm2 2.02.171 5.1.2 Utils LZMA 2.06 lzo 3.82 make man-db 2.6.3 mariadb 5.5.44 mariadb 10.1.13 mariadb 10.0.24 mariadb-galera 25.3.15 mdadm 3.3.2 2.1 microcode_ctl 3.2 mjet.ko 0.26 mlocate 17.0.0 mozjs 0.85 mtr 0.4.9 multipath-tools 1.6 net-tools nettle 2.7.1 1.0.6 NetworkManager newt 0.52.15 0.52.15 newt-python nspr 4.11 nss 3.21.0 nss 3.19.1 nss 3.16.2.3 Open Source License Copyright numactl-libs 2.0.9 LGPL-2.1 openvpn 2.3.10 GPL-2.0 Copyright (c) 2013 by the Open-Source OpenVPN development community ENGLISH OpenVPN is distributed under the GPL license version 2 (see below). In addition, as a special exception, OpenVPN Technologies, Inc. gives permission to link the code of this program with the OpenSSL library (or with modified versions of OpenSSL that use the same license as OpenSSL), and distribute linked combinations including the two. You must obey the GNU General Public License in all respects for all of the code used other than OpenSSL. If you modify this file, you may extend this exception to your version of the file, but you are not obligated to do so. If you do not wish to do so, delete this exception statement from your version. os-prober 1.58 GPL-2.0 pango 1.36.8 LGPL-2.1 Copyright (c) 1999 Red Hat Software parted 3.1 GPL-3.0 pciutils 3.2.1 GPL-2.0 Copyright (c) 1997-2013 Martin Mares
To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource.lge. com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to [email protected]. This offer is valid for a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information. Please be informed that LG Electronics products may contain open source software listed in the table below.
48 ENGLISH 49 Copyright Copyright (c) 1999-2012 The Apache Software Foundation Software Apache The 1999-2012 (c) Copyright Rights All Foundation. Software Apache The 2002-2014 (c) Copyright Reserved. Rights Reserved. All Foundation. Software Apache The 2015 (c) Copyright Foundation Software Apache The 2001-2007 (c) Copyright Foundation Software Apache The 2001-2013 (c) Copyright Foundation Software Apache The 2006-2017 (c) Copyright Foundation Software Apache The 2008-2016 (c) Copyright Foundation Software Apache The 2008-2016 (c) Copyright Consortium Systems 2017 Internet (c) Copyright 1998-2005 Abrahams, David Beman Dawes, (c) Copyright 2004-2007 Rene Rivera (c) Copyright CMS inc. 2011 Concrete (c) Copyright
52 ENGLISH 53 Copyright Copyright (c) 2012 Hannes Flicka (c) Copyright Software 1998 Red Hat (c) Copyright of California of the University 1980, 1990 Regents (c) Copyright [SGI] Inc. Graphics, 2000, 2001 Silicon (c) Copyright 1999-2010 Douglas Gilbert (c) Copyright 2011, Google Inc. Copyright
sudo 1.8.6p7 MIT-like License (sudo) ENGLISH tcp-wrappers 7.6 BSD-like License Copyright 1995 by Wietse Venema. Some individual files may be covered by (tcp-wrappers) other copyrights. tcpdump 4.5.1 BSD-3-Clause Copyright (c) 2005 The Tcpdump Group tcsh 6.18.01 BSD-3-Clause Copyright (c) 1980, 1991 The Regents of the University of California tiff 4.0.3 libtiff Copyright (c) 1988-1997 Sam Leffler Copyright (c) 1991-1997 Silicon Graphics, Inc. trousers 0.3.13 BSD-3-Clause Copyright (c) 2013, TrouSerS Project unzip 6.00 Info-ZIP Copyright (c) 1990-2009 Info-ZIP ustr 1.0.4 MIT Copyright (c) 2007 James Antill wpa_supplicant 2.0 BSD-3-Clause Copyright (c) 2002-2015 Jouni Malinen
54 ENGLISH 55 Copyright Copyright (c) 1986, 1987, 1988, 1989, 1994, 1998 The Open Group The 1998 1989, 1994, 1986, 1987, 1988, (c) Copyright Packard 2003 Keith 2001, (c) Copyright Oracle and/or its affiliates 2006 (c) Copyright Open Group The 1998 1990, (c) Copyright Packard 2003 Keith 2001, (c) Copyright Open Group The 1998 1989, (c) Copyright Hutterer 2008 Peter (c) Copyright Open Group The 2003 (c) Copyright Copyright (c)Maynard, Corporation, Digital1991, 1997 Equipment Massachusetts 1989-95 GROUPE BULL (c) Copyright Corporation Computer 2000 Compaq (c) Copyright Inc. Packard, 2002 Hewlett (c) Copyright Corporation 2006 Intel (c) Copyright Inc. 2008 Red Hat, (c) Copyright Airlie 2011 Dave (c) Copyright Packard 2006 Keith (c) Copyright Packard 2001, 2003 Keith (c) Copyright 2000 SuSE, Inc. (c) Copyright Packard 2013 Keith (c) Copyright Packard 2001, 2003 Keith (c) Copyright Maynard, Corporation, Digital Equipment 1987, 1988 by (c) Copyright Massachusetts UniSoft Limited 1990, 1991 by Group (c) Copyright Open Group The 1992, 1993, 1995, 1998 (c) Copyright 1992, 1994, 1995 X Consortium (c) Copyright 1995 Kaleb S. KEITHLEY (c) Copyright Hilaiel 2007-2009 Lloyd (c) Copyright 1995-2013 Jean-loup Gailly and Mark Adler (c) Copyright License X11 MIT HPND, X11 HPND X11 X11 X11 HPND HPND HPND HPND X11 X11 ISC Info-ZIP Zlib Open Source xorg-lib-libXext 1.3.3 xorg-lib-libXext 5.0.1 xorg-lib-libXfixes 1.5.1 xorg-lib-libXfont 2.3.2 xorg-lib-libXft 1.7.4 xorg-lib-libXi 1.1.3 xorg-lib-libXinerama 3.5.11 xorg-lib-libXpm 1.4.2 xorg-lib-libXrandr 0.9.8 xorg-lib-libXrender 1.2 xorg-lib-libxshmfence 1.1.4 xorg-lib-libXt 1.2.2 xorg-lib-libXtst 1.1.3 xorg-lib-libXxf86vm 2.0.4 yajl zip 3.0 zlib 1.2.7 ). (http://www.openssl.org/ Toolkit the OpenSSL use in the OpenSSL for Project by developed product includes software This This software is based in part JPEG Group. software of the Independent This on the work LG PCS400R Pro:Centric Server Warranty ENGLISH Welcome to the LG family! We believe that you will be pleased with your new PCS400R Pro: Centric Server. Broadcast Products Please read this warranty carefully, it is a “LIMITED WARRANTY”. This warranty gives you specific legal rights.
LG’s RESPONSIBILITY Warranty Term 1 year parts and labour from date of purchase or delivery date. New or remanufactured replacements for factory-defective parts may be used. Such replacement parts have a Parts warranty for the remaining portion of the original warranty period. Warranty service is provided by LG. Customer pays for shipping charges to LG; LG pays for return shipping Warranty Service Charge’s to return PCS400R Pro: Centric Server to customer. Call 0844 248 6655 for further information. WARRANTY SPECIFICS This warranty covers manufacturing defects and does not cover installation, adjustment of customer controls, Installation or repair of antenna systems, cable converters or cable company-supplied equipment; it also does not cover damage due to misuse, abuse, negligence, acts of God or other causes beyond the control of LG. Any alteration of the product after manufacture voids this warranty in its entirety. Not Covered THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND LG SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THIS PRODUCT. OWNER’S RESPONSIBILITY Warranty begins on the date of delivery of the PCS400R Pro: Centric Server. Effective Warranty Date For your convenience, keep the dealer’s dated bill of sale or delivery ticket, as evidence of the purchase date. Read the Installation & Setup Guide carefully so that you will understand the operation of the PCS400R Pro: Installation Guide Centric Server along with how to adjust the settings. For warranty service information, call 0844 248 6655. Parts and labour for service work carried out are LG’s responsibility (See above) will be provided without charge. Other service is at the owner’s expense. If you Warranty Service have any problem in obtaining satisfactory warranty service, call 0844 248 6655. You must provide the model number, serial number and date of purchase or date of original installation. For Customer Support/Service, please call: 0844 248 6655 www.lg.com
Pro:Centric, the “Pro:Centric” logo, and the “LG” logo are registered trademarks of LG Electronics Inc. Java and the “Java Powered” logo are trademarks of Oracle. All other trademarks or registered trademarks are the property of their respective owners. 56