Hitachi Command Suite CR210H Server Option Quick Start Guide

•

No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or stored in a database or retrieval system for any purpose without the express written permission of Hitachi, Ltd.

Hitachi, Ltd., reserves the right to make changes to this document at any time without notice and assumes no responsibility for its use. This document contains the most current information available at the time of publication. When new or revised information becomes available, this entire document will be updated and distributed to all registered users.

Some of the features described in this document might not be currently available. Refer to the most recent product announcement for information about feature and product availability, or contact Hitachi Data Systems Corporation at https://portal.hds.com.

Notice: Hitachi, Ltd., products and services can be ordered only under the terms and conditions of the applicable Hitachi Data Systems Corporation agreements. The use of Hitachi, Ltd., products is governed by the terms of your agreements with Hitachi Data Systems Corporation.

Hitachi is a registered trademark of Hitachi, Ltd., in the United States and other countries. Hitachi Data Systems is a registered trademark and service mark of Hitachi, Ltd., in the United States and other countries.

Archivas, Essential NAS Platform, HiCommand, Hi-Track, ShadowImage, Tagmaserve, Tagmasoft, Tagmasolve, Tagmastore, TrueCopy, Universal Star Network, and Universal Storage Platform are registered trademarks of Hitachi Data Systems Corporation.

AIX, AS/400, DB2, Domino, DS8000, Enterprise Storage Server, ESCON, FICON, FlashCopy, IBM, Lotus, OS/ 390, RS6000, S/390, System z9, System z10, Tivoli, VM/ESA, z/OS, z9, zSeries, z/VM, z/VSE are registered trademarks and DS6000, MVS, and z10 are trademarks of International Business Machines Corporation.

All other trademarks, service marks, and company names in this document or website are properties of their respective owners.

Microsoft product screen shots are reprinted with permission from Microsoft Corporation.

Hitachi Command Suite CR210H Server Option Quick Start Guide Hitachi Command Suite CR210H Server Option Quick Start Instructions

Follow these instructions to install and start your system equipment.

Check packaged items

Confirm that all system parts listed in the Packaged Items Checklist are contained with no damage. If any items are missing, or if there are any problems with the packaged items, contact the dealer from whom you purchased the system equipment.

Install the rack rails

When you mount the system unit to the rack cabinet, use the rack rails provided for exclusive use with the system unit. Use a Hitachi rack cabinet or an EIA standard rack.

The following steps describe the procedure to install the rack rails in a rack cabinet. 1. Slide out the inner rail from outer rail while pressing the button on the inner rail until the inner rail stops. Then the inner rail is locked by lock latch (white). 2. Further slide out the inner rail while pulling the lock latch (white), and disengage the inner rail.

1 Hitachi Command Suite CR210H Server Option Quick Start Guide 3. Slide the outer rail back while lifting the lock lever.

2 Hitachi Command Suite CR210H Server Option Quick Start Guide 4. Align the guide at the front of the outer rail with the guide hole at the front of the rack cabinet and lock the guide into the hole.

5. Release the lock lever at the rear of the outer rail, align the guide with the guide hole at the rear of the rack cabinet 6. Lock the guide into the hole, and engage the lock lever to fix the outer rail to the rack cabinet.

3 Hitachi Command Suite CR210H Server Option Quick Start Guide 7. Repeat with the other outer rail.

4 Hitachi Command Suite CR210H Server Option Quick Start Guide Attach the rack rails to the system unit and install in a rack 1. Align the hole of the inner rails to the tabs of the system unit. Then place and slide the inner rails toward the front of the system unit.

2. Align the inner rails on either side of the system unit with the outer rails. 3. Slide the inner rails into the outer rails until the inner rails stop and are locked by lock latches (White). 4. Pull the lock latches (Blue) and slide the inner rails all the way into the rack cabinet. Then the inner rails are locked by the buttons.

5 Hitachi Command Suite CR210H Server Option Quick Start Guide Set up network connectivity

Perform the following steps to set up network connections. 1. Connect the system network cable to the Management interface connector port, as shown.

2. Install the Remote Console Application to your PC. The CR210H Remote Console Application, and manual, are included in the media package. 3. Set the IP address. The default IP address shown below is set as the factory. If you want to change the IP address, connect to the system using the default IP address, and then change the IP address.

Item Default

IP address 192.168.100.100 Subnet mask 255.255.255.0 Default gateway address 192.168.100.20

Connect power

Connect the power cord to the power supply at the rear of the system.

CAUTION! If you remove the power plug from the system unit or the outlet, wait at least 30 seconds before reconnecting the power plug. Otherwise the system might not start.

6 Hitachi Command Suite CR210H Server Option Quick Start Guide After connecting the power cord to the system, fix the power cord using a cable clamp attached to the power unit to prevent disconnection. After fixing the power cord, push the cable clamp in the direction of the power plug.

Power on the system

When you connect the power cord to AC power, the SERVICE LED at the front and rear of the system will blink for approximately 60 seconds. The MAINTENANCE LED remains off at this time. While the SERVICE LED blinks, pressing the POWER LED switch turns on the system. However, the system does not start until the SERVICE LED stops blinking.

To turn on power to the system, press the POWER LED on the front of the system. It will turn green.

Item Name

A POWER LED switch (green) B SERVICE LED switch (blue) C ERROR LED (orange) DACCESS LED (green)

If power is lost to the system due to a tripped circuit breaker or a power plug being removed, wait 60 seconds before restoring power to the unit.

Once POST has started memory check, do not turn off power until the OS starts. Otherwise, the system might not start properly.

When AC power is supplied to the system, the SERVICE LED on the front and rear of the system unit blinks for about 60 seconds.

Even if the POWER LED switch is pushed while the SERVICE LED is blinking, the system is turned on but does not work until the blinking stops.

7 Hitachi Command Suite CR210H Server Option Quick Start Guide Set up the operating system

Windows is pre-installed on your system at the factory.

NOTE: Hitachi Data Systems has completed the Microsoft Windows Server software license agreement and HBA installation on behalf of the customer.

Logon procedure

You will need to log on as Windows Administrator. 1. Enter the password for Administrator in [New password] and [Confirm password], and then click the [OK] button. The default password is Hitachi123!. 2. Change the default password to a password of your choice.

TIP: Combine three of more of the following characters. The password must satisfy the following conditions: • Upper-case letters A to Z • Lower-case letters a to z • Numerics 1 to 9 • Symbols such as a comma and a period

Do not use three or more consecutive characters contained in the user’s name or full name. 3. The system displays “Your password has been changed.” Click the [OK] button.

Hitachi Command Suite software for Windows

Hitachi Command Suite software is pre-installed at the factory.

Network configuration on Windows

Add an entry on “hosts” (C:\Windows\System32\drivers\etc\hosts) to make sure the appliance server’s IP address can be resolved as IPv4 address. For example:

10.208.115.205 ha8kxj02

This is necessary since IPv4 address communication is required between HDvM and HTnM, HTnM Server and HTnM agent for RAID. All of them are installed on the same server, but IPv4 is required for inter-process communication.

8 Hitachi Command Suite CR210H Server Option Quick Start Guide 1

Hitachi Command Suite CR210H Server Option Quick Start Guide Hitachi Data Systems Corporate Headquarters 2845 Lafayette Street Santa Clara, California 95050-2639 U.S.A. www.hds.com Regional Contact Information Americas +1 408 970 1000 [email protected] Europe, Middle East, and Africa +44 (0) 1753 618000 [email protected]

Asia Pacific +852 3189 7900 [email protected]

MK-90CRH038-00