ENGLISH

MONITOR WITH RECEIVER INSTRUCTION MANUAL

DMX6018BT

This instruction manual is used to describe the models listed above. Model availability and features (functions) may differ depending on the country and sales area.

© 2017 JVC KENWOOD Corporation B5A-2146-20 (EN)

01_DDX_2018TC_E_COVER.indd 1 12/10/2018 4:55:49 PM Important Notice

To ensure proper use, please read through this CAUTIONS For Israel manual before using this product. It is especially important that you read and observe WARNINGS To care for the unit and CAUTIONS in this manual. • If you have parked the car for a long time in hot or Please keep the manual in a safe and accessible cold weather, wait until the temperature in the car place for future reference. becomes normal before operating the unit. To care for the monitor WARNINGS • The monitor built into this unit has been produced with high precision, but it may have some ineffective To prevent accidents and damages dots. This is inevitable and is not considered • DO NOT install any unit or wire any cable in a defective. location where; • Do not expose the monitor to direct sunlight. – it may obstruct the steering wheel and gearshift • Do not operate the touch panel using a ball-point lever operations. pen or similar tool with a sharp tip. – it may obstruct the operation of safety devices such Touch the keys on the touch panel with your finger as air bags. directly (if you are wearing a glove, take it off). – it may obstruct visibility. • When the temperature is very cold or very hot... • DO NOT raise the volume level too much, as this will – Chemical changes occur inside, causing make driving dangerous by blocking outside sounds, malfunction. and may cause hearing loss. – Pictures may not appear clearly or may move • DO NOT operate the unit while driving. If you need slowly. Pictures may not be synchronized with to operate the unit while driving, be sure to look the sound or picture quality may decline in such around carefully. environments. • Stop the car before performing any complicated On the volume setting operations. • Digital devices produce very little noise compared • The driver must not watch the monitor while driving. with other sources. Lower the volume before playing these digital sources to avoid damaging the speakers by sudden increase of the output level.

i ENGLISH

EN_DDX2018TC_E.indb i 2017/11/29 15:51 Important Notice

English Hereby, JVCKENWOOD declares that the radio equipment “DMX6018BT” is in compliance with Directive 2014/53/EU. Declaration of Conformity with regard to the The full text of the EU declaration of conformity is Information on Disposal of Old Electrical and RE Directive 2014/53/EU available at the following internet address: Electronic Equipment and Batteries (applicable Declaration of Conformity with regard to the http://www.kenwood.com/cs/ce/eudoc/ for countries that have adopted separate waste RoHS Directive 2011/65/EU collection systems) Manufacturer: Français Products and batteries with the symbol (crossedout JVC KENWOOD Corporation Par la présente, JVCKENWOOD déclare que wheeled bin) cannot be disposed as household waste. 3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, l’équipement radio « DMX6018BT » est conforme à la Old electrical and electronic equipment and batteries Kanagawa, 221-0022, Japan directive 2014/53/UE. should be recycled at a facility capable of handling EU Representative: L’intégralité de la déclaration de conformité UE est these items and their waste byproducts. JVCKENWOOD Europe B.V. disponible à l’adresse Internet suivante : Contact your local authority for details in locating a Amsterdamseweg 37, 1422 AC UITHOORN, http://www.kenwood.com/cs/ce/eudoc/ recycle facility nearest to you. THE NETHERLANDS Proper recycling and waste disposal will help conserve Deutsch resources whilst preventing detrimental effects on our Hiermit erklärt JVCKENWOOD, dass das Funkgerät health and the environment. “DMX6018BT” der Richtlinie 2014/53/EU entspricht. Notice: The sign “Pb” below the symbol for batteries Der volle Text der EU-Konformitätserklärung steht indicates that this battery contains lead. unter der folgenden Internetadresse zur Verfügung: http://www.kenwood.com/cs/ce/eudoc/

Nederlands Hierbij verklaart JVCKENWOOD dat de radioapparatuur “DMX6018BT” in overeenstemming is met Richtlijn 2014/53/EU. De volledige tekst van de EU-verklaring van overeenstemming is te vinden op het volgende internetadres: http://www.kenwood.com/cs/ce/eudoc/

ENGLISH ii

EN_DDX2018TC_E.indb ii 2017/11/29 15:51 Important Notice

Italiano Český Slovensko Con la presente, JVCKENWOOD dichiara che Společnost JVCKENWOOD tímto prohlašuje, že rádiové S tem JVCKENWOOD izjavlja, da je radijska oprema l΄apparecchio radio “DMX6018BT” è conforme alla zařízení “DMX6018BT” splňuje podmínky směrnice »DMX6018BT« v skladu z Direktivo 2014/53/EU. Direttiva 2014/53/UE. 2014/53/EU. Celotno besedilo direktive EU o skladnosti je dostopno Il testo integrale della dichiarazione di conformità UE è Plný text EU prohlášení o shodě je dostupný na na tem spletnem naslovu: disponibile al seguente indirizzo internet: následující internetové adrese: http://www.kenwood.com/cs/ce/eudoc/ http://www.kenwood.com/cs/ce/eudoc/ http://www.kenwood.com/cs/ce/eudoc/ Slovensky Español Magyar Spoločnosť JVCKENWOOD týmto vyhlasuje, že rádiové Por la presente, JVCKENWOOD declara que el equipo JVCKENWOOD ezennel kijelenti, hogy a „DMX6018BT“ zariadenie „DMX6018BT“ vyhovuje smernici 2014/53/ de radio “DMX6018BT” cumple la Directiva 2014/53/EU. rádióberendezés megfelel a 2014/53/EU irányelvnek. EÚ. El texto completo de la declaración de conformidad Az EU konformitási nyilatkozat teljes szövege az alábbi Celý text EÚ vyhlásenia o zhode nájdete na con la UE está disponible en la siguiente dirección de weboldalon érhető el: nasledovnej internetovej adrese: internet: http://www.kenwood.com/cs/ce/eudoc/ http://www.kenwood.com/cs/ce/eudoc/ http://www.kenwood.com/cs/ce/eudoc/ Svenska Dansk Português Härmed försäkrar JVCKENWOOD att radioutrustningen Herved erklærer JVCKENWOOD, at radioudstyret Deste modo, a JVCKENWOOD declara que o “DMX6018BT” är i enlighet med direktiv 2014/53/EU. “DMX6018BT” er i overensstemmelse med Direktiv equipamento de rádio “DMX6018BT” está em Den fullständiga texten av EU-försäkran om 2014/53/EU. conformidade com a Diretiva 2014/53/UE. överensstämmelse finns på följande Internetadress: EU-overensstemmelseserklæringens fulde ordlyd er O texto integral da declaração de conformidade da UE http://www.kenwood.com/cs/ce/eudoc/ tilgængelig på følgende internetadresse: está disponível no seguinte endereço de internet: http://www.kenwood.com/cs/ce/eudoc/ http://www.kenwood.com/cs/ce/eudoc/ Suomi JVCKENWOOD julistaa täten, että radiolaite Ελληνικά Polska “DMX6018BT” on direktiivin 2014/53/EU mukainen. Με το παρόν, η JVCKENWOOD δηλώνει ότι ο Niniejszym, JVCKENWOOD deklaruje, że sprzęt radiowy EU-vaatimustenmukaisuusvakuutusvaatim us löytyy ραδιοεξοπλισμός «DMX6018BT» συμμορφώνεται με “DMX6018BT” jest zgodny z dyrektywą 2014/53/UE. kokonaisuudessaan seuraavasta internet-osoitteesta: την Οδηγία 2014/53/ΕΕ. Pełny tekst deklaracji zgodności EU jest dostępny pod http://www.kenwood.com/cs/ce/eudoc/ Το πλήρες κείμενο της δήλωσης συμμόρφωσης της adresem: ΕΕ είναι διαθέσιμο στην ακόλουθη διεύθυνση στο http://www.kenwood.com/cs/ce/eudoc/ διαδίκτυο: http://www.kenwood.com/cs/ce/eudoc/

iii ENGLISH

EN_DDX2018TC_E.indb iii 2017/11/29 15:51 Important Notice

Eesti HRVATSKI / SRPSKI JEZIK Русский Käesolevaga JVCKENWOOD kinnitab, et „DMX6018BT“ JVCKENWOOD ovim izjavljuje da je radio oprema JVCKENWOOD настоящим заявляет, что raadiovarustus on vastavuses direktiiviga 2014/53/EL. “DMX6018BT” u skladu s Direktivom 2014/53/EU. радиооборудование «DMX6018BT» соответствует ELi vastavusdeklaratsiooni terviktekst on kättesaadav Cjeloviti tekst deklaracije Europske unije o usklađenosti Директиве 2014/53/EU. järgmisel internetiaadressil: dostupan je na sljedećoj internet adresi: Полный текст декларации соответствия ЕС доступен http://www.kenwood.com/cs/ce/eudoc/ http://www.kenwood.com/cs/ce/eudoc/ по следующему адресу в сети Интернет: http://www.kenwood.com/cs/ce/eudoc/ Latviešu ROMÂNĂ JVCKENWOOD ar šo deklarē, ka radio aparatūra Prin prezenta, JVCKENWOOD declară că echipamentul Українська „DMX6018BT” atbilst direktīvas 2014/53/ES prasībām. radio “DMX6018BT” este în conformitate cu Directiva Таким чином, компанія JVCKENWOOD заявляє, Pilns ES atbilstības deklarācijas teksts ir pieejams šādā 2014/53/UE. що радіообладнання «DMX6018BT» відповідає tīmekļa adresē: Textul integral al declaraţiei de conformitate UE este Директиві 2014/53/EU. http://www.kenwood.com/cs/ce/eudoc/ disponibil la urmatoarea adresă de internet: Повний текст декларації про відповідність ЄС можна http://www.kenwood.com/cs/ce/eudoc/ знайти в Інтернеті за такою адресою: Lietuviškai http://www.kenwood.com/cs/ce/eudoc/ Šiuo JVCKENWOOD pažymi, kad radijo įranga БЪЛГАРСКИ „DMX6018BT“ atitinka 2014/53/EB direktyvos С настоящото JVCKENWOOD декларира, че reikalavimus. радиооборудването на “DMX6018BT” е в Visą EB direktyvos atitikties deklaracijos tekstą galite съответствие с Директива 2014/53/ЕС. rasti šiuo internetiniu adresu: Пълният текст на ЕС декларацията за съответствие е http://www.kenwood.com/cs/ce/eudoc/ достъпен на следния интернет адрес: http://www.kenwood.com/cs/ce/eudoc/ Malti B’dan, JVCKENWOOD jiddikjara li t-tagħmir tar-radju Turkish “DMX6018BT” huwa konformi mad-Direttiva 2014/53/ Burada, JVCKENWOOD “DMX6018BT” radyo UE. ekipmanının 2014/53/AB Direktifine uygun olduğunu It-test kollu tad-dikjarazzjoni ta’ konformità huwa bildirir. disponibbli fl-indirizz intranet li ġej: AB uyumluluk deklarasyonunun tam metni aşağıdaki http://www.kenwood.com/cs/ce/eudoc/ internet adresinde mevcuttur. http://www.kenwood.com/cs/ce/eudoc/

ENGLISH iv

EN_DDX2018TC_E.indb iv 2017/11/29 15:51 About this manual Contents The displays and panels shown in this manual are Component Names and Operations ...... 3 Bluetooth® ...... 20 examples used to provide clear explanations of the Basic Operations ...... 3 Information ...... 20 operations. For this reason, they may be different Turning on the power ...... 3 Preparation ...... 20 from the actual displays or panels. Turning off the power/turning off the AV source ...... 3 Connection...... 20 Putting the unit in standby ...... 3 Bluetooth mobile phone ...... 22 This manual mainly explains operations using the Turning off the screen ...... 4 Bluetooth audio player ...... 25 buttons on the monitor panel and keys on the Adjusting the volume ...... 4 Bluetooth mobile phone settings ...... 26 touch panel. For operations using the remote Attenuating the sound ...... 4 Settings ...... 26 controller, see page 35. Monitor panel operations ...... 4 Audio settings ...... 26 Getting Started ...... 5 Display settings ...... 31 < > indicates the various screens/menus/ Initial settings ...... 5 User interface settings ...... 32 operations/settings that appear on the touch Setting the security function...... 5 Camera settings ...... 33 panel. Calendar/clock settings ...... 6 Special system settings ...... 34 Bluetooth settings ...... 34 Various Screens and Operations ...... 6 [ ] indicates the keys on the touch panel. Security settings ...... 35 Touch screen operations ...... 6 Indication language: English indications are used Home screen ...... 7 Remote Controller ...... 35 for the purpose of explanation. You can select the Source control screen ...... 8 Preparation ...... 35 Basic operations for KNA-RCDV331 (optionally indication language from the menu. List/setting screen...... 10 purchased) ...... 36 (Page 33) Video ...... 10 KENWOOD Remote APP ...... 37 USB ...... 11 Installation and Connection ...... 38 iPod/iPhone ...... 12 Before installation ...... 38 Apps—WebLink™ ...... 13 Installing the unit...... 39 Radio ...... 14 Removing the unit ...... 40 Spotify ...... 17 Connecting external components ...... 40 Wiring connection ...... 41 Other External Components ...... 19 References ...... 42 Rear view camera ...... 19 Maintenance ...... 42 AV-IN ...... 19 More information ...... 42 Troubleshooting ...... 44 Specifications ...... 46 Trademarks and licenses ...... 49

2 ENGLISH

03_DDX_2018TC_E_Body01.indd 2 12/10/2018 4:57:27 PM Component Names and Operations Basic Operations

8 /VOICE button Turning on the power • (Press): Displays the App screen. (Page 14) • VOICE (Hold): Activates the voice dialing. 9 AV button Displays the current source control screen.

*1 DO NOT expose the remote sensor to bright light (direct sunlight Turning off the power/turning off the AV or artificial lighting). *2 The function of the button when held varies depending on source the setting on the screen. • This function varies depending on the setting. (Page 34) 1 Remote sensor*1 2 Screen (touch panel) 3 Monitor panel (Hold) 4 VOLUME K/J button 5 ATT/DISP OFF button Putting the unit in standby • ATT (Press): Attenuates the sound. • DISP OFF (Hold): Turns off the screen. 6 HOME button 1 Display the source/option selection • (Press): Turns on the power. screen. • (Hold): Turns off the power or AV source.*2 On the Home screen, touch as follows: • HOME (Press): Displays the Home screen while the power is on. 7 MENU/CAMERA button • MENU (Press): Pops up the short-cut menu. Put the unit in standby. • CAMERA (Hold): Displays the picture from the 2 On the source/option selection screen, touch as connected rear view camera. follows:

ENGLISH 3

EN_DDX2018TC_E.indb 3 2017/11/29 15:51 Basic Operations

Turning off the screen Attenuating the sound 3 Perform the adjustment or operation. On the monitor panel

The ATT indicator lights up. (Hold) To cancel attenuation: Press the same button again. To turn on the screen: Press the same button on the monitor panel or touch the screen. Monitor panel operations E.g. Angle adjust screen On the pop-up short-cut menu [0] – [6] Selects a monitor angle. 1 Display the pop-up short-cut menu. (The monitor panel will stay in 1 Display the pop-up short-cut menu. this angle when you turn on the unit.) Sets the angle of the monitor 2 On the pop-up short-cut menu, touch as panel you want when you 2 On the pop-up short-cut menu, touch as follows: turn off the unit or the ignition switch of the vehicle. follows: • Select the monitor angle, Display OFF then touch [Memory]. • To return to the previous screen, touch [ ] on the To turn on the screen: Touch the screen. setting screen.

Adjusting the volume

You can adjust the volume (00 to 40) by pressing J to increase and pressing K to decrease. • Holding J increases the volume continuously to level 15.

4 ENGLISH

EN_DDX2018TC_E.indb 4 2017/11/29 15:51 Getting Started

Initial settings [Display] (Page 31) 2 Display the screen. Make the settings to adjust the display. On the Home screen, touch as follows: When you power on the unit for the first time, the [Camera] (Page 33) screen appears. Make the settings to display the picture from the Perform the initial settings. connected view camera. [DEMO] Then, on the screen, touch as follows: • ON (Initial): Activates the display demonstration. [Security] → [Security Code Set] • OFF: Deactivates the display demonstration. 3 Enter a four-digit number (1), then confirm the entry (2). Setting the security function Registering a security code E.g. Initial settings screen You can set a security code (four-digit number of Once completed, a warning message appears. Touch your choice) to protect your receiver system against [Agree] to display the Home screen. theft. Once you set the security code, you are required to input the security code when the power is on to [Language] reconnect the battery. Select the text language used for on-screen • To clear the last entry, touch [BS]. information. 1 Display the Home screen. • To cancel the setting, touch [ ]. Touch [Language Select], then select the language. • American English (en)/British English (en) (Initial)/ 4 Enter the four-digit number entered in Nederlands (nl)/Français (fr)/Deutsch (de)/ step 3 and touch [Enter] again to confirm Italiano (it)/Español (es)/(ar) /Ελληνικά (el)/ your security code. Português (pt)/Čeština (cs)/Polski (pl)/ Magyar (hu)/Руccĸий (ru)/ (th)/ To change the security code: Touch [Security Code Türkçe (tr)/ (zh)/(he) /(fa) / Change] on the screen on step 2, then Bahasa Melayu (ms)/Bahasa Indonesia (id) repeat steps 3 and 4. [Clock] (Page 6) To clear the security code: Touch [Security Code Set the calendar and clock time. Cancellation] on the screen on step 2, Make the settings for [Clock], [Time Zone] or [Clock then repeat step 3. Adjust].

ENGLISH 5

EN_DDX2018TC_E.indb 5 2017/11/29 15:51 Getting Started Various Screens and

Calendar/clock settings 3 Set the date and clock. Operations

1 Display the Home screen. You can display or change to other screens at any time to show information, change the AV source, change the settings, etc.

Touch screen operations 2 Display the screen. On the Home screen, touch as follows: To perform operations on the screen, you need to [Clock] touch, touch and hold, flick or swipe to select an item, Select the method to set the date and clock. display setting menu screen or to change the page, • RDS-SYNC (Initial): Synchronizes the clock with etc. the FM Radio Data System. Then, on the screen, touch [User • Manual: Sets the date and clock manually. Touch Interface]. Touch the screen gently to select an [Time Zone]* item on the screen. Select the time zone for your area. [Clock Adjust]* Set the date and clock manually when [Clock] is Touch and hold set to [Manual]. Touch the screen and keep your Touch [J]/[K] to adjust the date (year/month/ finger in place until the display date), then clock (hour/minute). To finish setting, changes or a message is displayed. touch [Set]. Flick * Available when [Clock] is set to [Manual]. Slide your finger to the left or right on the screen to change the page.

Swipe Slide your finger up or down on the screen to scroll the screen.

6 ENGLISH

EN_DDX2018TC_E.indb 6 2017/11/29 15:51 Various Screens and Operations

Home screen Available playback sources and options To change the page: Touch [ ]/[ ]. Current page is Touch 4 to display the source/option selection screen. shown by the page indication on the bottom of the When you turn on the power for the first time, the screen. Home screen appears. To return to the Home screen: Touch [ ] on the • You can customize the Home screen. source/option selection screen. • To display the Home screen from other screens, press Radio HOME on the monitor panel. Customizing the source/option selection iPod USB AV-IN screen You can arrange the items to display on the source/ E.g. Source/option selection screen option selection screen. Touching the operation keys performs the following 1 Select an item to move. actions: Touch and hold the item you want to move until [WebLink] Switches to the WebLink™ boxes appear around the icons. application. 2 Drag the selected item to the position you [Bluetooth] Plays a Bluetooth audio player. want to move it to. E.g. Home screen [Radio] Switches to the radio broadcast. Touching the operation keys performs the following [Spotify] Switches to the Spotify application. actions: [iPod] Plays an iPod/iPhone. 1 Displays the current playing source control screen Radio [USB] Plays files on a USB device. 2 Clock/date 3 Current source information [AV-IN] Switches to an external component iPod USB AV-IN 4 Displays all playback sources and options connected to the AV-IN input 5 Short-cut playback source keys terminal. E.g. Source/option selection screen 6 Displays the phone control screen [Audio] Displays the sound adjustment screen. [STANDBY] Puts the unit in standby. [ ] Displays the screen.

ENGLISH 7

03_DDX_2018TC_E_Body01.indd 7 1/7/2019 9:20:37 AM Various Screens and Operations

About short-cut playback source keys on the Source control screen 5 Information about connected device Home screen • For Bluetooth device: Signal strength and battery The three items displayed on the top of the source/ You can perform the playback operation from the level (only when the information is acquired from option selection screen with large icons are also source control screen during playback. the device) shown on the Home screen as the short-cut playback • The operation keys and information displayed vary 6 Track/file/song/video information source keys. You can set the source keys which you use depending on the selected source/file type being • Touching [] scrolls the text if not all of the text frequently and access quickly from the Home screen. played. is shown. • If the operation keys are not displayed on the screen, 7 Clock display touch the screen to show them. 8 Displays the track/file/station/channel list 9 Displays/hides other available operation keys* p Displays the source/option selection screen q Operation keys* w Secondary screen Each time you touch [ ]/[ ] , the items shown on the secondary screen change as follows: • Indicators: Displays the current source conditions, etc. The followings are the common indicators: − ATT: The sound is attenuated. E.g. Common audio playback source screen − LOUD: The loudness is active. − MUSIC/VIDEO: Music/video file is played back. 1 Playback source or media type • Short-cut buttons: Changes the source from 2 Picture data/artwork (shown if the file contains those you have located on the Home screen. artwork) e Displays the phone control screen 3 For video: Hides the operation buttons on the screen while video is played * See “Common operation keys on source control screen” on • Touch the screen to restore the operation page 9. buttons. For audio: File format 4 Repeat/random playback mode keys*

8 ENGLISH

EN_DDX2018TC_E.indb 8 2017/11/29 15:51 Various Screens and Operations

Common operation keys on source control screen q 2 Select an item to jump. • The appearance of the operation keys may differ, [ ] Displays the however the similar operation keys have the same screen. operations. • Available operation keys differ depending on the [ ] Displays the folder list/track list/audio selected source or connected device. menu/video menu. [S]/[T] • (Touch) Selects an item (folder/track/ Touching the operation keys performs the following audio file/video file). actions: • (Hold) Reverses/forwards search. [IW] Starts/pauses playback. 4 [ ]* Selects repeat playback mode. * About playback mode: • : Repeat one – Available playback mode differs depending on the source, file E.g. Pop-up short-cut menu screen • : Repeat folder type, connected device, etc. 1 Displays the picture adjustment screen. • ALL: Repeat all – You cannot activate repeat playback mode and random (Page 11) • (gray): Off playback mode at the same time. 2 Turns off the screen. [ ]* Selects random playback mode. 3 Displays the screen. • : Random folder Using the pop-up short-cut menu (Page 4) • ALL: Random all While displaying the source control screen, you can 4 Displays the screen. (Page 31) • (gray): Off jump to another screen by touching the operation 5 Displays the sound adjustment screen. keys on the pop-up short-cut menu. 6 Displays the current source control screen. 9 7 Closes the pop-up short-cut menu. 1 Display the pop-up short-cut menu. [ ] Displays other available operation keys 8 Changes the playback source. besides those shown on q. • The three short-cut playback source keys • To hide the window, touch [ ]. displayed on the Home screen are displayed [SETUP] Displays the setting screen of the on the short-cut menu. current playback source. 9 Displays the phone control screen. (Page 23) [ ][ ] Selects a folder.

ENGLISH 9

EN_DDX2018TC_E.indb 9 2017/11/29 15:51 Various Screens and Operations Video

Using touch screen operation during Playback operations playback Video playback information on the source control screen

Touching the operation keys performs the following Touching the areas performs the following actions: actions: 1 Displays the source control screen. 1 Displays list type selection window. 2 Goes to the previous track.* 2 Selects the file type ([ ]: audio/[ ]: video). 3 Goes to the next track.* 3 Exits from the current screen or returns to the E.g. Video playback source control screen * Not available for video from an external component (AV-IN). previous screen. 4 Scrolls the text if not all of the text is shown. 1 Media type 2 Hides the operation buttons on the screen. List/setting screen 5 Play/search keys • [I Play]: Plays all tracks in the folder containing • Touch the screen to restore the operation The followings are the common operation keys which the current track. buttons. appear on the list/settings screen. • [ A-Z]: Enters alphabet search to list the items 3 Repeat/random playback mode keys • The appearance of the operation keys may differ, in alphabetical order. When a keypad appears, 4 Current playback item information/audio format however the similar operation keys have the same touch the first letter you want to search for. 5 Playback status/playing time operations. • [ Top]: Returns to the root folder. 6 Indicators • Available operation keys differ depending on the • [ Up]: Returns to the upper layer. • VIDEO: Lights up when video is played. setting screens. Not all the following operation keys 6 Changes the page to display more items. are shown on every screen. • [J]/[K]: Scrolls the page. • [ ]/[ ]: Jumps to the top or bottom page.

10 ENGLISH

EN_DDX2018TC_E.indb 10 2017/11/29 15:51 Video USB

Adjusting the picture Adjusts the brightness of the You can connect a USB mass storage class device such backlight. (−4 to +4) as a USB memory, digital audio player, etc. to the unit. • For playable file types and other information, see 1 Display the pop-up short-cut menu. Adjusts the contrast. (−4 to +4) pages 42 and 43. Adjusts the brightness. (−4 to +4) • You cannot connect a PC or portable HDD to the *1 Adjusts the color. (−4 to +4) USB input terminal. *2 Adjusts the tint. (−4 to +4) • You cannot connect a USB device via a USB hub. Display the picture adjustment screen. 2 Selects the aspect ratio. On the pop-up short-cut menu, touch as follows: • Full: Changes the aspect ratio of Connecting a USB device video and displays fully on the • Use CA-U1EX for extending the cable if necessary. screen. (Max 500 mA, 5V) • Normal: Displays the video in 3 Adjust the picture. the aspect ratio of 4:3. USB device (commercially available) • Auto*3: Displays the video fully on vertical or horizontal with no ratio change. • Adjustable items are different depending on the current source. Rear panel • You can perform this function only when you have applied the parking brake.

*1 Adjustable only during playback. *2 Available only when the “AV-IN” or camera screen is displayed. *3 Selectable only when video from a USB device is played back.

ENGLISH 11

EN_DDX2018TC_E.indb 11 2017/11/29 15:51 USB iPod/iPhone

Playback operations From : Connecting an iPod/iPhone 1 Select the file type ([ ]: audio/[ ]: video). Playback information and key operation 2 Select a category, then the item in the selected • For playable iPod/iPhone types and other category. • For playback information, see “Source control screen” information, see page 43. on page 8. • You cannot watch video. • For key operations on the touch panel, see “Common Wired connection operation keys on source control screen” on iPod/iPhone (commercially available) page 9. • All tracks in the USB device will be played repeatedly until you change the source or disconnect the USB device. From : Selecting a folder/track on the list 1 Select the file type ([ ]: audio/[ ]: video). 2 Select the tag type to display a list of contents USB Audio cable for iPod/iPhone: KCA-iP103 Display the folder/track list. 1 that contains the same tag as the track/file (optional accessory) On the source control screen, touch as follows: currently being played, then select the item.

Rear panel 2 Select the list type.

From : 3 Select the desired track. Select the folder, then the item in the selected • Repeat the procedure until you select the desired folder. track. • For details about the list operation, see page 10. Bluetooth connection Pair the iPod/iPhone with this unit via Bluetooth. (Page 20)

12 ENGLISH

EN_DDX2018TC_E.indb 12 2017/11/29 15:51 iPod/iPhone Apps—WebLink™

Playback operations 3 Select the desired track. You can display and control the App on the unit • Repeat the procedure until you select the desired while your smartphone is connected to the USB input Playback information and key operation track. terminal. Preparation: Be sure to ground the PRK SW lead. • For playback information, see “Source control screen” • For details about the list operation, see (Page 41) on page 8. page 10. • For key operations on the touch panel, see “Common From : operation keys on source control screen” on Select a category, then the item in the selected Available Apps page 9. category. You can use the following Apps on this unit. Install the • Available categories differ depending on the type WebLink™ App on your smartphone beforehand. Selecting an audio file from the menu of iPod/iPhone. WebLink™ 1 Display the list. WebLink™ enables you to use the following Apps with On the source control screen, touch as follows: the unit. • Media Player • Yelp • YouTube • OpenWeatherMap 2 Select the list type. From : Select the tag type to display a list of contents that contain the same tag as the track/file currently being played, then select the item.

ENGLISH 13

03_DDX_2018TC_E_Body01.indd 13 12/10/2018 4:57:50 PM Apps—WebLink™ Radio

Connecting a smartphone Start playback Listening to the radio

Android™ device iPhone (commercially 1 Select “WebLink” as the source. Playback information on the source control (commercially available) available) screen 2 Operate on the unit to select App. • On the “WebLink” source screen, you can also operate on the touch panel as follows:

[ ] • Displays the main menu of the FM 01

“WebLink” source screen. FM 02 • Exits the current App. FM 03 USB cable (commercially available) [ ] • Returns to the previous screen. • Exits the current App. FM 04

USB Audio cable for iPod/iPhone: 3 Operate on your smartphone. KCA-iP103 (optional accessory) • When you are asked to communicate between E.g. Radio source control screen your smartphone and the unit, touch [Allow] to 1 Displays/hides other available operation keys* proceed. 2 Preset no. Rear panel • If App does not start while using “WebLink”, start 3 Changes the seek mode for [S]/[T] Rear panel the App on your smartphone. • AUTO1 (Initial): Auto search • AUTO2: Tunes in preset stations one after Switching to the App screen while listening another to the another source • MANUAL: Manual search You can display the App screen while listening to the 4 Text information other source. • Touching [<] scrolls the text if not all of the text is shown. • Touching [ ] switches the information (e.g. frequency, PS name, Radio Text, title, artist, etc.). • When the smartphone is connected to the unit and −The availability of the information vary “WebLink” is selected as the source, a confirmation depending on the reception, selected station. message to communicate with each other appears 5 Preset list on the smartphone. Touch [Allow] to establish 6 Selects the band (AM/FM) connection, or [Ignore] to cancel the connection. 7 Operation keys* • You can check the connection status on the WebLink™ screen on your smartphone. 14 ENGLISH

03_DDX_2018TC_E_Body01.indd 14 12/10/2018 4:58:00 PM Radio

8 Indicators Touching the operation keys performs the following [PTY]* (For FM Radio Data System features) • NEWS: Lights up when News Standby Reception actions: Enters PTY search mode. is activated. 1 1 Touch a PTY code. • AF: Lights up when Network-Tracking Reception [TI]* (For FM Radio Data System features) 2 Touch [Search] to search for. is activated. Activates TI standby reception mode. If there is a station broadcasting a • TI: Lights up in white when receiving the traffic • When TI is activated, the unit is ready to program of the same PTY code as you information, and lights in orange when Traffic switch to traffic information if available. have selected, that station is tuned in. Information Reception is on standby. The TI indicator lights up in white. • You can set language displayed for the • LO.S: Lights up when Local Seek is activated. • If the TI indicator lights up in orange, PTY search on the • ST: Lights up when receiving a stereo broadcast. tune into a station providing Radio Data screen. (Page 17) • MONO: Lights up when receiving stations in System signals. [AME] Presets stations automatically. monaural forcibly. • The volume adjustment for traffic • RDS: Indicates the status of the Radio Data information is automatically System station reception when the Network- memorized. The next time the unit 7 Tracking Reception is activated. (Page 17) switches to traffic information, the [S]/[T] Searches for a station. −Lights in white: Radio Data System station is volume is set to the memorized level. • The search method differs according being received. • To deactivate, touch [TI] again. to the selected seek mode. −Lights in orange: Radio data System station is [SETUP]* Displays the screen. not being received. * Appears only when FM is selected as the source. • EON: Lights up when a Radio Data System station [MONO]* Activates monaural mode for better FM is sending EON signals. reception (stereo effect will be lost). • The MONO indicator lights up while * See the following “Operation keys on source control screen”. monaural mode is activated. Operation keys on source control screen • To deactivate, touch [MONO] again. • The appearance of the operation keys may differ, [LO.S]* You can tune in FM stations only with however the similar operation keys have the same strong signals—Local Seek. operations. • ON: Tunes in only to FM stations with • See also “Common operation keys on source control sufficient signal strength. The LO.S screen” on page 9. indicator lights up. • OFF (Initial): Deactivates the function.

ENGLISH 15

EN_DDX2018TC_E.indb 15 2017/11/29 15:51 Radio

Storing preset stations in the memory Manual presetting Selecting a preset station You can preset 15 stations for FM and 5 stations for 1 Select the band, then tune in to a station 1 Select the band, then display the preset AM. you want to store. station list. • See “Playback information on the source control On the source control screen, touch as follows: Automatic presetting — AME (Auto screen” on page 14 for details. Memory) 2 Display the preset list. On the source control screen, touch as follows: On the source control screen, touch as follows: 2 Select a preset station.

A confirmation message appears. Touch [Yes]. 3 Select a preset number to store into. The local stations with the strongest signals are found and stored automatically.

(Hold) To hide the preset list: Touch [ ] on the preset list.

The station selected in step 1 is stored into the preset number you have selected. To hide the preset list: Touch [ ] on the preset list.

16 ENGLISH

EN_DDX2018TC_E.indb 16 2017/11/29 15:51 Radio Spotify

Settings for tuner reception [Regional] With Spotify, your music is everywhere. Working out, When driving in an area where FM reception is not partying or relaxing, the right music is always at your fingertips. There are millions of songs on Spotify—from 1 Display the screen. sufficient enough, this unit automatically tunes in old favorites to the latest hits. Just choose the music On the source control screen, touch as follows: to another FM Radio Data System station of the same program with stronger signals— Network- you love, or let Spotify surprise you. Tracking Reception (Regional). • ON (Initial): Switches to another station You can stream Spotify from iPhone/iPod touch or broadcasting the same program.*2 Android devices. • Because Spotify is a third-party service, the 2 Make the settings. • OFF: Deactivates the function. specifications are subject to change without [Auto TP Seek] prior notice. Accordingly, compatibility may be When traffic information station reception is poor, impaired or some or all of the services may become the unit automatically searches for another station unavailable. that can be received better—Auto TP Seek. • Some functions of Spotify cannot be operated from • ON (Initial): Automatically searches for a station this unit. with better reception for traffic information if the • For issues using the application, contact Spotify at current reception of current station is poor. . • OFF: Deactivates the function. [NEWS]*1 [Language select] • 00min to 90min: Activates New Standby Select the language to display for PTY search. Reception by selecting the period of time to • British English (en) (Initial)/Espanol (es)/ disable the interruption. The NEWS indicator Francais (fr)/Nederlands (nl)/Norsk (no)/ lights up. Portugues (pt)/Svenska (sv)/Deutsch (de) • OFF (Initial): Deactivates the function. [AF] To close the setting window, touch [Close]. When driving in an area where FM reception is not *1 The volume adjustment for Traffic Information is automatically sufficient enough, this unit automatically tunes in memorized. The next time the unit switches to Traffic to another FM Radio Data System station of the Information, the volume is set to the previous level. same network with stronger signals— Network- *2 The RDS indicator lights up when the Network-Tracking Tracking Reception (AF: Alternative Frequencies). Reception is activated. • ON (Initial): Switches to another station. The – Lights in white: Radio Data System station is being received. program may differ from the one currently – Lights in orange: Radio data System station is not being received.*2 received. • OFF: Deactivates the function.

ENGLISH 17

EN_DDX2018TC_E.indb 17 2017/11/29 15:51 Spotify

Preparation Playback operations Operation keys on source control screen • The appearance of the operation keys may differ, Installing the application Playback information and key operation however the similar operation keys have the same operations. Your smartphone must has built in Bluetooth and the • See also “Common operation keys on source control following profiles must be supported: Spotify screen” on page 9. • SPP (Serial Port Profile) • A2DP (Advanced Audio Distribution Profile) Touching the operation keys performs the following Establish an Internet connection using LTE, 3G, EDGE, actions: or Wi-Fi. Ensure you are logged in to your smartphone 3 application. If you do not have a Spotify account, you [ ]*1 Thumbs down to the current track and can create one for free from your smartphone or at skips to the next track. . [ ]*1 Registers the current track as a favorite. E.g. Spotify source control screen Install the latest version of the Spotify application on [ ]*2 *3 Activates ( )/deactivates ( ) your smartphone. You can also operate Spotify with optional remote shuffle playback mode. • For Android devices: Search for “Spotify” in Google controller, KNA-RCDV331. [ ]*2 Selects repeat playback mode Play to find and install the most recent version. You can only control play, pause and skip with the ( : repeat one*3/ ALL: repeat all/ • For iPhone/iPod touch: Search for “Spotify” in the remote controller. : repeat off). Apple iTunes App Store to find and install the most recent version. 1 Playing time 5 2 Picture data [ ] Displays the Spotify menu screen. 3 Thumb up/down and repeat/shuffle playback Connecting the device [ ] Creates a new station (Start Radio). For Android devices mode keys* [ ]*2 *3 [ ] Selects a track. Pair the Android device with this unit via Bluetooth. 4 Track information (Page 20) • Touching [<] scrolls the text if not all of the text [ ][ ] Starts (I)/pauses (W) playback. is shown.

For iPhone/iPod touch 5 Operation keys* [ ] Saves the current track/artist/album to • Via USB input terminal: Connect iPhone/iPod touch or . with the cable KCA-iP103 (optional accessory). * See the following “Operation keys on source control screen”. *1 Not available for tracks in a playlist. (Page 12) *2 Not available for tracks in the Radio. • Via Bluetooth: Pair the iPhone/iPod touch with this *3 Available only for premium account users. unit. (Page 20)

18 ENGLISH

EN_DDX2018TC_E.indb 18 2017/11/29 15:51 Spotify Other External Components

Creating your station (Start Radio) Rear view camera To exit the camera screen Press HOME on the monitor panel or touch the area Start Radio is to start a radio channel based on the Install the rear view camera (separately purchased) in shown below. currently played track. the appropriate position according to the instructions Create your station. supplied with the rear view camera. On the source control screen, touch as follows: Connecting a rear view camera See page 40 for more information for connection terminals. • To use the rear view camera, a reverse lead (REVERSE) Station is created and playback starts automatically. connection is required. (Page 41) AV-IN • You can personalize your station using thumb up ([ ]) or thumb down ([ ]). Connecting an external component Using the rear view camera – Personalizing stations may not be available See page 40 for connection terminals. depending on the track. • For rear view camera settings, see “Camera settings” on page 33. Starting playback Selecting a track To display the rear view camera screen The rear view camera screen is displayed by shifting 1 Select “AV-IN” as the source. 1 Display the Spotify menu screen. the gear to the reverse (R) position when [R-CAM On the Home screen, touch as follows: On the source control screen, touch as follows: Interruption] is set to [ON] on the screen. (Page 33) • A caution message appears on the screen. To remove the caution message, touch the screen. 2 Turn on the connected component and 2 Select the list type, then select a desired start playing the source. item. You can also display the picture from the rear view • For playback information, see “Source control • The list types displayed differ depending on the camera manually without shifting the gear to the screen” on page 8. information sent from Spotify. reverse (R) position. On the monitor panel:

(Hold)

ENGLISH 19

EN_DDX2018TC_E.indb 19 2017/11/29 15:51 Bluetooth®

Information Connection Registering a Bluetooth device 1 Search for the unit (“DMX6”) from your Bluetooth is a short-range wireless radio When you connect a Bluetooth device to the unit for Bluetooth device and operate the device communication technology for mobile devices such as the first time: mobile phones, portable PCs and other devices. 1 Register the device by pairing the unit and the to register. Bluetooth devices can be connected without cables device. For a Bluetooth device compatible with SSP and communicate with each other. 2 Connect the device to the unit. (Page 21) (Bluetooth 2.1): Confirm the request both on the device and the Note Registering a new Bluetooth device unit. • While driving, do not perform complicated Pairing allows Bluetooth devices to communicate with On the device: operations such as dialing numbers, using each other. the phonebook, etc. When you perform these • The pairing method differs depending on the operations, stop your car in a safe place. Bluetooth version of the device. • Some Bluetooth devices may not connect to this unit – For devices with Bluetooth 2.1: depending on the Bluetooth version of the device. You can pair the device and the unit using SSP • This unit may not work for some Bluetooth devices. (Secure Simple Pairing) which only requires • Connecting conditions may vary depending on your confirmation. On the unit: environment. – For devices with Bluetooth 2.0: • For some Bluetooth devices, the device is You need to enter a PIN code both on the device disconnected when the unit is turned off. and the unit for pairing. • If your mobile phone supports PBAP (Phone Book • Once connection is established, it is registered in the Access Profile), you can display the following items unit even if you reset the unit. Up to 10 devices can on the touch panel when the mobile phone is be registered in total. connected. • Two Bluetooth devices for Bluetooth phone and one – Phonebook: up to 1 000 entries for Bluetooth audio can be connected at a time. – Dialed calls, received calls, and missed calls (up to • To use the Bluetooth function, you need to turn on • Touch [No] to reject the request. 50 entries in total) the Bluetooth function of the device. For a Bluetooth device compatible with Auto pairing Bluetooth 2.0: Preparation When is set to [ON] on the screen, iOS (such as iPhone) devices are shown on the screen (initial: “0000”). details, see page 41. automatically paired when connected via USB. To change PIN code, see page 22. • Set [Bluetooth] to [ON] on the screen. (Page 26) (Page 34)

20 ENGLISH

EN_DDX2018TC_E.indb 20 2017/11/29 15:51 Bluetooth®

2 Determine usage as a hands free device 4 When your Bluetooth device is compatible 2 Select the device you want to connect/ (1), then touch [Close] (2). with PBAP: Select whether to transfer the disconnect. phonebook of your Bluetooth device to the unit or not. [Yes] Select to transfer the phonebook from your Bluetooth device. [No] Select this when you do not want to transfer the phonebook.

The icons beside the registered device indicate the Connecting/disconnecting a registered following: [Hands Free1]/ Select hands free number to • / : Connected as a mobile phone. [Hands Free2] use as the hands free device. Bluetooth device • : Connected as an audio player. [No Connection.] Select this when you do not 1 Display the screen. want to use as the hands free On the Home screen, touch as follows: 3 Select the usage of the device (1), then device. touch [Close] (2).

3 When your Bluetooth device is compatible with A2DP or SPP: Determine usage as Then, on the screen, touch [Bluetooth]. an audio player or a device with Apps installed. On the screen, touch [Select Device]. [Yes] Select to use the device as an audio player. [No] Select this when you do not want to use the Bluetooth device as an audio player. Each time you touch the selection, the usage is selected (“ ” appears) or deselected (“ ” disappears). Select to connect and deselect to disconnect the device. [TEL (HFP)1]/ Select to use as the hands free [TEL (HFP)2] device. [Audio (A2DP)/ Select to use as the audio App (SPP)] player or device with Apps installed.

ENGLISH 21

EN_DDX2018TC_E.indb 21 2017/11/29 15:51 Bluetooth®

To delete the registered Bluetooth device: Touch Changing the device name of the unit Bluetooth mobile phone [Delete] in step 2, select devices to delete, then touch displayed on the paired device [Delete]. A confirmation message appears. Touch When a call comes in... [Yes]. 1 Display the • To select all devices, touch [ All]. screen. • To deselect all selected devices, touch [ All]. On the Home screen, touch as follows: Changing the PIN code 1 Display the screen. On the Home screen, touch as follows: Then, on the screen, touch [Bluetooth]. On the screen, touch [Device Touching the operation keys performs the following Name]. actions: 2 Enter the device name (1), then confirm [ ] Answers a call. Then, on the screen, touch [Bluetooth]. the entry (2). [ ] Rejects a call. On the screen, touch [PIN Code]. [Speech Displays the Quality] screen. 2 Enter the PIN code (1), then confirm the • Microphone Level: Adjusts the entry (2). microphone volume level. (–10 to 10, initial: 0) • Echo Cancel Level: Adjusts the echo volume level. (OFF, –5 to 5, Initial: 0) • To clear the last entry, touch [BS]. • Noise Reduction Level: Adjusts the • To move the entry position, touch [H]/[I]. noise reduction volume. (OFF, –5 to 5, Initial: 0) • Call information is displayed if acquired. • To clear the last entry, touch [BS]. • Phone operation is not available while the picture from the view camera is displayed.

22 ENGLISH

EN_DDX2018TC_E.indb 22 2017/11/29 15:51 Bluetooth®

During a call... Making a call • If the selected contact has several phone numbers, the phone number list is displayed. 1 Display the phone control screen. Select a phone number to make a call. On the Home screen, touch as follows: To use alphabet search in the phonebook 1 Touch [ A-Z ]. 2 Touch the first letter you want to search for on the keypad. To search for a number, touch [1]. 2 Select a method to make a call. 3 Select a contact you want to call from the list. Touching the operation keys performs the following • You can select a first name or last name to use actions: when sorting the list in alphabetical order on the [ ] Ends a call. screen. (Page 26)

[ ] Mutes the volume of the microphone. B When item 4 is selected in step 2: [ ]/ Switches between hands free mode Enter the phone number (1), then make a [ ] and phone mode. call (2). 1 From the call history* (missed calls/received [DTMF] Enters DTMF (Dual Tone Multi calls/dialed calls) Frequency), then sends text using the 2 From the phonebook* keypad. 3 From the preset list (Page 24) [Speech Displays the 4 Use direct number entry Quality] screen. 5 Use voice dialing • See page 22 for details. 3 Select a contact to make a call. A When item 1, 2 or 3 is selected in step 2: • To enter “+”, touch and hold [0/+]. • To clear the last entry, touch [BS]. * Applicable only for mobile phone compatible with PBAP (Phone Book Access Profile).

ENGLISH 23

EN_DDX2018TC_E.indb 23 2017/11/29 15:51 Bluetooth®

C When item 5 is selected in step 2: Presetting phone numbers 3 Select a method to add a phone number Say the name of the person you want to You can preset up to eight phone numbers. to preset list and register the number to call. the preset list (1), then touch [Close] (2). Display the screen. • You can also make voice dialing by pressing and 1 On the Home screen, touch as follows: holding the VOICE on the monitor panel. • Available only when the connected mobile phone has a voice recognition system. • If the unit cannot find the target, “Press [Restart] to restart the voice recognition process.” appears. Then, on the phone control screen, touch as Touch [Restart], then say the name again. follows: • To cancel voice dialing, touch [Stop]. [ ] → [Edit] Switching between two connected devices 2 Select a position to store into. [Add Select a phone number from number from the phonebook. You can change the device to use when two devices phonebook] are connected. [Add number Enter a phone number on the On the phone control screen: direct] direct number entry screen, then touch [Set] to add to the preset list.

• To display the preset list, touch [ ] on the phone control screen.

To delete a phone number from the preset list: The active device is highlighted. Select the phone number to delete on the screen, then touch [Delete] in step 3. To delete all phone numbers from the preset list: Touch [Delete all] on the screen in step 2.

24 ENGLISH

EN_DDX2018TC_E.indb 24 2017/11/29 15:51 Bluetooth®

Editing phonebook Bluetooth audio player Playback information and key operation To transfer the phonebook • For playback information, see “Source control If the connected Bluetooth mobile phone is screen”on page 8. compatible with Phone Book Access Profile (PBAP), Bluetooth • For key operations on the touch panel, see “Common you can transfer the phonebook of the mobile phone operation keys on source control screen” on to the unit. page 9.

1 Display the phone control screen. Additional keys operations: Touching the operation On the Home screen, touch as follows: keys performs the following actions. [BT DEVICE Switches to another Bluetooth audio CHANGE] player. E.g. Bluetooth source control screen 2 Start phonebook data transmission. 1 Displays/hides other available operation keys*1 Selecting a track from the list 2 Artwork (Shown if the track contains artwork) 1 Display the music list. 3 Connected device name On the source control screen, touch as follows: 4 Repeat/random playback mode keys*1 5 Signal strength and battery level (Appears only when the information is acquired from the device.) 6 Tag data*2 (current track title/artist name/album 2 Select the folder, then the item in the title) selected folder. To delete contact from the phonebook: Touch • Pressing [<] scrolls the text if not all of the text is • For details about the list operation, see [ ] in step 2 (2), select devices to delete, then shown. page 10. touch [Delete]. A confirmation message appears. 7 Operation keys*1 Touch [Yes]. *1 See “Common operation keys on source control screen” on • To select all devices, touch [ All]. page 9. • To deselect all selected devices, touch [ All]. *2 Available only for devices compatible with AVRCP 1.3. • Touch [ A-Z ] to search the contact by initial.

ENGLISH 25

EN_DDX2018TC_E.indb 25 2017/11/29 15:51 Bluetooth® Settings

Bluetooth mobile phone settings Audio settings Select the speakers used for Bluetooth mobile You can change various settings for using Bluetooth phones. 1 Display the

26 ENGLISH

EN_DDX2018TC_E.indb 26 2017/11/29 15:51 Settings

Setting the speakers and crossover 3 Select the speaker type (1), then adjust Preparation: frequency the crossover frequency (2) of the Before making the adjustment for , selected speaker. select the appropriate crossover network mode 1 Select a car type (1), select a speaker X’over Front Rear Subwoofer according to the speaker system (2-way speaker (2) (front speakers, rear speakers, or HPF FREQ system or 3-way speaker system). subwoofer) to set, then location* and 100 Hz Slope speaker/tweeter size (3) of the selected -6 dB/Oct

Gain 1 Put the unit in standby. speaker. 0 dB On the Home screen, touch as follows: A selection window appears for each setting. Select TW Gain an item, then touch [Close] to close the window. -1 dB

Speaker Select • Adjustable items vary depending on the selected

Car Type speaker type/speaker size/crossover settings. Comfort Then, on the source/option selection screen, touch Speaker [STANDBY]. 4 inch Location Adjusts the crossover frequency for the front or rear Door 2 Display the screen. Tweeter speakers (high pass filter). Medium X’over On the monitor panel, press the following buttons at the same time: Adjusts the crossover frequency for the speaker • Repeat steps 2 and 3 to set all speakers. (low pass filter). • Adjustable items vary depending on the selected speaker type. Adjusts the crossover slope. • When a speaker is not connected, select [None]. 3 Select the crossover network mode. • When setting the front speakers, also select the Adjusts the output volume of the selected speaker. speaker size for . [2way] Select this when 2-way system speakers are used (front/rear). 2 Touch [X’over] to display the Adjusts the output volume of the tweeter. [3way] Select this when 3-way system screen. speakers are used (tweeter/mid Selects the phase for the speaker. range/woofer).

A confirmation message appears. Touch [Yes]. * Speaker location selection is available only when is set to [2way].

ENGLISH 27

EN_DDX2018TC_E.indb 27 2017/11/29 15:51 Settings

Store your own sound adjustments • To apply the adjusted equalizer to all playback source, touch [ALL SRC], then touch [OK] to The following adjustments are memorized for each confirm. source until you adjust the sound again. 1 Select a preset sound mode. • To clear the adjustment, touch [Initialise]. You cannot adjust the sound when the unit is in 2 Select a band (1) and adjust the level (2), standby. then adjust the sound (3). * Not adjustable when is selected for subwoofer on the screen. (Page 27) Selecting a preset sound mode Graphic Equalizer USB ALL SRC 1 Display the preset sound modes. You can adjust the sound effects according to your listening position. You can also localize the sound image in front of the selected seat. Preset Select Bass EXT SW Level

ON OFFOFF Initialise Memory 0 2 Select a preset sound mode. Setting the listening position • Pops/Easy/Top40/Jazz/Powerful/Rock/Flat 1 (Initial)/iPod/User1/User2/User3/User4 Adjust the sound as follows: Touch [Listening Position] ( ), then select the listening position ([Front L], [Front R], Graphic Equalizer iPod ALL SRC [Front All]*, or [All]) (2). Activates/deactivates bass. • ON/OFF (Initial) Position/DTA Listening Position Front Focus

Adjusts the subwoofer level.* Front L Front R Pops Easy Top40 Jazz Powerful Rock • –50 to +10 (Initial: 0) Flat iPod User1 User2 User3 User4 Front All All

3 Repeat step 2 to adjust the level of other Adjust To hide the preset sound modes: Touch [ ]. bands. 4 Touch [Memory] to store adjustment. * [Front All] is selectable only when is set to [2way]. A user selection window appears. Select from [User1] to [User4] to store your adjustment, then touch [Close] to close the window.

28 ENGLISH

EN_DDX2018TC_E.indb 28 2017/11/29 15:51 Settings

Adjusting the Digital Time Alignment (DTA) To initialize the setting value: Touch [Initialise]. [Sound Image LR (Front)] Adjusts the sound image to be localized set on the Make fine adjustments to the delay time of the speaker Localizing the sound image—Front Focus front position. output to create a more suitable environment for your car. 1 Touch [Front Focus] (1), select the [Sound Image LR (Rear)] listening position (2) to set as the front Adjusts the sound image to be localized set on the 1 Touch [Adjust] on the rear position. screen to display the DTA adjustment position, then touch [Adjust] (3). [Size of the Virtual Sound Field] screen. Position/DTA Adjusts the virtual sound field to the desired field 2 Touch [Delay] (1), then adjust the Digital Listening Position Front Focus size. • If the sound image moves out of the front Time Alignment (DTA) value (2) for each Front L Front R Front All Front All position, adjust [Sound Image LR (Front)]/ speaker. Priority L Priority R All All Priority L Priority R [Sound Image LR (Rear)]. Position/DTA Initialise Adjust [Subwoofer Delay]

Front L Front R Adjusts the delay time of the subwoofer sound. 0 feet 0 feet 0 ms 0 ms Rear L Rear R • When you are sitting on the [Front All] (front 0 feet 0 feet 1 0 ms 0 ms seats) or [All] (front and rear seats) position, select 3 Touch [Level] ( ), then adjust the output volume (2) for each speaker. Subwoofer Delay left (“Priority L”) or right (“Priority R”) to specify 0 feet 0 ms Level the position to localize the sound image. Front Focus Adjust Initialise

Tweeter

1 0 dB • To determine the adjustment value, see 2 Touch [Delay] ( ), then adjust the sound image (2) precisely. Front L Front R “Determining the value for 0 dB 0 dB

Rear L Rear R adjustment” on page 30. Front Focus Adjust Initialise 0 dB 0 dB

Delay 3 Touch [Level] (1), then adjust the output Sound Image LR(Front) Subwoofer 0 dB Level Sound Image LR(Rear) 0.00ms 0.00ms volume (2) for each speaker. Size of the Virtual Sound Field

Subwoofer Delay 0.00ms 0.00ms Position/DTA Initialise

Tweeter Delay To initialize the setting value: Touch [Initialise]. 0 dB 0.00ms 0.00ms Level Front L Front R

0 dB 0 dB

Rear L Rear R

0 dB 0 dB

Subwoofer Delay

0 dB Level

ENGLISH 29

EN_DDX2018TC_E.indb 29 2017/11/29 15:51 Settings

Determining the value for Adjusts loudness. (The LOUD indicator lights up when adjustment Touch [J]/[K]/[H]/[I] or drag the mark to adjust. If you specify the distance from the center of the the loudness is adjusted.) currently set listening position to every speaker, the • OFF (Initial)/Low/High Adjusts the front and rear speaker output balance. delay time will be automatically computed and set. When using a two-speaker system, set the fader to the 1 Determine the center of the currently set Reduces the driving noise by raising the bandwidth. center (0). listening position as the reference point. • OFF (Initial)/ON • F15 to R15 (Initial: 0) 2 Measure the distances from the reference point * to the speakers. Virtually enhances the sound space using the Digital 3 Calculate the differences between the distance of Adjusts the left and right speaker output balance. Signal Processor (DSP) system. Select the enhance the furthest speaker and other speakers. • L15 to R15 (Initial: 0) level. 4 Set the DTA value calculated in step 3 for To clear the adjustment: Touch [Center]. • OFF (Initial)/Small/Medium/Large individual speakers. 5 Adjust gain for individual speakers. Restores the sound lost due to audio compression to a E.g. When [Front All] is selected as the listening Adjust and store the auto-adjustment volume level realistic sound. position for each source. The volume level will automatically • OFF/ON (Initial) increase or decrease when you change the source. +90 cm If you have increased the volume first, then reduced Virtually makes the sound more realistic using the the volume using the Volume Offset, the sound Digital Signal Processor (DSP) system. Select the sound generated if you suddenly switch to another source level. may be extremely loud. • OFF (Initial)/1/2/3 60 cm • –5 to +5 (Initial: 0) 80 cm To initialize the setting value: Touch [Initialise]. Moves the localization of the sound image to the lower or higher point. Select the height. 150 cm +70 cm • OFF (Initial)/Low/Middle/High Adjust the sound effect. * You cannot change the setting when “Radio” is selected as the source. +0 cm Selects the bass boost level. • OFF (Initial)/1/2/3

30 ENGLISH

EN_DDX2018TC_E.indb 30 2017/11/29 15:51 Settings

Display settings To change the background color: Touch [Background Color], then select the color on the You can change the illumination color of the buttons screen. Display the screen. on the monitor panel. On the Home screen, touch as follows: • You can select same color selected in Key Color as the background color by touching [Sync Color Settings]. • If [Scan] is selected in , user cannot User Scan select [Sync Color Settings]. Then, on the screen, touch [Display].

Adjust *1 Selects background color in advance. SETUP *2 Selects a loaded favorite image in advance.

• You can also adjust the illumination color yourself. Display User Interface Camera Special Storing your favorite image for the Touch [Adjust] to display the illumination color adjustment screen, then adjust the color. The background Bluetooth Security adjustment is saved in [User]. You can use your favorite image stored on the • Selecting [Scan] changes the illumination color connected USB device for the background. E.g. Setup screen gradually. • Connect the USB device on which the image is stored beforehand. • Use a JPEG/PNG/BMP file with a resolution of 800 x 480 pixels. • ON: Activates dimmer. You can change the background design or color. • OFF: Deactivates dimmer. To change the background design: 1 Touch [User1 Select] or [User2 Select] to • SYNC (Initial): Dims the screen and button store the image for the illumination when you turn on the headlights. screen. 2 Select the folder, then the file for the background image in the selected folder. • ON (Initial): Displays the clock while a video source User Background Select is playing. • OFF: Cancels. *1 *2

ENGLISH 31

EN_DDX2018TC_E.indb 31 2017/11/29 15:51 Settings

3 Rotate the image (1) if necessary, then User interface settings 2 Select a function to assign to the selected confirm the selection (2). button. Display the screen. On the Home screen, touch as follows:

Then, on the screen, touch [User Interface].

Assign functions to the keys on the remote controller 3 Repeat steps 1 and 2 to register other A confirmation message appears. Touch [Enter] of the steering wheel. functions to other buttons. to store the new image. (The existing image is • This function is available only when your car is 4 Touch [Learning completed] to finish replaced with the new one.) equipped with the electrical steering remote procedure. controller. A confirmation message appears. Touch [Yes]. • You can only register/change the functions while you are parked. • The unit can register/change all of the buttons’ Select the viewing angle in relation to the monitor to • If your steering remote controller is not compatible, functions at the same time. To do this, press all make the image on the screen easier to see. learning may not be completed and an error buttons in turn and after pressing all of them, touch • 0 (Initial)/–1/–2/–3 message may appear. [Learning completed] in step 2. However, new functions cannot be learned after this operation. 1 When the unit is ready for learning, press • When changing the functions already learned, touch and hold a steering remote controller the assigned function you want to change in step 2 button for about 2 seconds to register/ and then touch to select the new function from the change. function list. • Refer to the message displayed to confirm • Confirm the contents of the settable functions in the whether the unit ready before proceeding. function list. You cannot edit the function list. To initialize the setting: Touch [Learning initialisation] in step 2. • A confirmation message appears. Touch [Yes]. – To cancel the initialization, touch [No].

32 ENGLISH

EN_DDX2018TC_E.indb 32 2017/11/29 15:51 Settings

*1 *2 • ON (Initial): Activates the key-touch tone. Select the time zone for your area. For details, see • ON (Initial): Displays the parking guidelines. • OFF: Deactivates the key-touch tone. “Calendar/clock settings” on page 6. • OFF: Hides the parking guidelines.

*2 Select the text language used for on-screen Adjust the date and clock manually. For details, see Adjust the parking guidelines according to the size of information. For details, see “Initial settings” on “Calendar/clock settings” on page 6. the car, parking space and so on. page 5. When adjusting the parking guidelines, make sure to *1 Available only when is set to [2way]. use the parking brake to prevent the car from moving. *2 Available when [Clock] is set to [Manual]. Touch one of the marks (1), then adjust the Adjust the touch positions of the buttons on the position of the selected mark (2). screen. Camera settings Touch and hold the center of the marks at the lower Display the screen. left (1), then the upper right (2) as instructed. On the Home screen, touch as follows:

(Hold) Initialise Then, on the screen, touch [Camera]. Make sure that A and B are horizontally parallel, and that C and D are the same length. • ON: Displays the picture from the rear view camera • Touch [Initialise] to set all the marks to the initial (Hold) when you shift the gear to the reverse (R) position. default position. A confirmation message appears. • To reset the touch position, touch [Reset]. • OFF (Initial): Select this when no camera is Touch [Yes]. • To cancel the current operation, touch [Cancel]. connected.

Select the method to set the date and clock. For • ON: Selects when you connect an external system details, see “Calendar/clock settings” on page 6. unit. (Neither buttons nor titles are displayed.) • OFF (Initial): Selects when a rear view camera is connected.

ENGLISH 33

EN_DDX2018TC_E.indb 33 2017/11/29 15:51 Settings

Special system settings • Equalizer (Adjustment on user preset ([User1] – Bluetooth settings [User4])/Subwoofer level adjustment) Display the screen. • Position/DTA Display the screen. On the Home screen, touch as follows: • Sound Effect On the Home screen, touch as follows: A confirmation message appears. Touch [Yes].

when pressed and held. Connect or disconnect the paired device. (Page 21) • AV OFF: Turns off the screen and audio. Display the information of the software (such as serial The screen and audio restores when receiving call, number, application version, system version, etc.). You inputs video signal from the rear view camera, etc. can update the software. Display/change the device name to be shown on the • Complete OFF (Initial): Turns off the power. Bluetooth device. (Page 22) Show the Open Source Licenses. • Lock: Locks the

34 ENGLISH

EN_DDX2018TC_E.indb 34 2017/11/29 15:51 Settings Remote Controller

Security settings Optional remote controller KNA-RCDV331 is designed Preparation for controlling this unit. Refer to the instruction manual Display the screen. that comes with the remote controller. Battery installation On the Home screen, touch as follows: Use two “AAA”/“R03”-size batteries. CAUTION Insert the batteries with the + and – poles aligned • Put the remote controller in a place where it will properly, following the illustration inside the case. not move during braking or other operations. A Then, on the screen, touch [Security]. dangerous situation could result if the remote controller falls down and gets wedged under the pedals while driving. Register the security code for the unit. (Page 5) • Do not leave the battery near fire or under direct sunlight. A fire, explosion or excessive heat generation may result. • Do not recharge, short, break up or heat the battery, Clear the security code. (Page 5) or place it in an open fire. Such actions may cause the battery to leak fluid. If spilled fluid comes in • Always insert batteries from – poles to avoid bending contact with your eyes or clothing, immediately rinse the springs. Change the security code. (Page 5) with water and consult a physician. • If the remote controller operates only over shorter • Place the battery out of reach of children. In the distances or does not operate at all, it is possible that unlikely event that a child swallows the battery, the batteries are depleted. In such instances, replace immediately consult a physician. both batteries with new ones.

ENGLISH 35

EN_DDX2018TC_E.indb 35 2017/11/29 15:51 Remote Controller

Remote controller mode switch Basic operations for KNA-RCDV331 Common operations (AUD mode) The functions operated from the remote controller (optionally purchased) SRC • Selects the source. differ depending on the position of the mode switch. • Hangs up the incoming/current call.

AUD VOL J/K Adjusts the volume level. t DVD t ATT Attenuates/restores the sound. TV t t NAV VOICE/FNC/ For USB/iPod: Switches to the MENU/PBC current source control screen. ENTER Enters options. • AUD mode: Switch to this mode when controlling a selected source or tuner source, etc. Answers incoming calls. – When controlling a player that is not integrated in ROUTE M/ Changes the aspect ratio. the unit, select “AUD” mode. MODE/ • The aspect ratio changes each

• DVD mode: Not used. TOP MENU time you press this key. • TV mode: Not used. VIEW/AV OUT Switches the AV source to be • NAV mode: Not used. output. • The position of the remote control mode switch is indicated in the title of each mode, e.g., “AUD mode”. MAP DIR/OPEN Adjusts the panel angle. • The panel angle changes each time you press this key. NAV/DISP Switches to the current source control screen. ZOOM OUT/IN Not used for this unit. 2 ZONE Not used for this unit.

R.VOL Not used for this unit.

36 ENGLISH

EN_DDX2018TC_E.indb 36 2017/11/29 15:51 Remote Controller

Radio (AUD mode) USB (AUD mode) KENWOOD Remote APP KENWOOD Remote is an application that connects J/FM+ / K/AM− Selects the band. J/FM+ / K/AM− Selects a folder. and controls compatible KENWOOD car receivers via H/S / T/I Searches for stations.* H/S / T/I Selects a file. Bluetooth® like a wireless remote control. POSITION/IW Changes the seek mode (AUTO1, POSITION/IW Starts/pauses playback. You can also operate this unit from a smartphone AUTO2, MANUAL). using KENWOOD Remote APP.

0 – 9 Specifies the frequency of the This application can display the source information station to receive to search for in Searching for a station frequency directly of this unit on the smartphone’s screen, and enables direct search. While listening to the radio, you can search for a the user to make an audio setting using the graphic user interface of this application. # BS/DIRECT Enters direct search mode. station frequency directly using the number buttons. This application also works as a free standalone 1 Press # BS/DIRECT to enter the search * The search method differs according to the selected seek mode. music player application, when your smartphone is mode. not connected to this unit. • For details, visit . H/S / T/I Selects music/videos. • To erase a misentry, press * +/CLEAR. POSITION/IW Starts/pauses playback. 3 Press H/S / T/I to confirm.

To exit the search mode: Press # BS/DIRECT.

ENGLISH 37

EN_DDX2018TC_E.indb 37 2017/11/29 15:51 Installation and Connection

WARNINGS Before installation • Keep all cables away from heat dissipating metal parts. • DO NOT connect the ignition wire (red) and the Precautions on installation and connection • If your car’s ignition does not have an ACC position, battery wire (yellow) to the car chassis (ground), you connect the ignition wires to a power source that • Mounting and wiring this product requires skills and may cause a short circuit, that in turn may start a fire. can be turned on and off with the ignition key. If you experience. For best safety, leave the mounting and • DO NOT cut out the fuse from the ignition wire (red) connect the ignition wire to a power source with a wiring work to professionals. and the battery wire (yellow). The power supply must constant voltage supply, such as with battery wires, • Mount the unit so that the mounting angle is 30° or be connected to the wires via the fuse. the battery may be drained. less. • Always connect the ignition wire (red) and the • If the console has a lid, make sure to install the unit • Make sure to ground the unit to a negative 12 V DC battery wire (yellow) to the power source running so that the monitor panel will not hit the lid when power supply. through the fuse box. closing and opening. • Do not install the unit in a location exposed to direct • If the fuse blows, first make sure the wires are not sunlight or excessive heat or humidity. Also avoid touching to cause a short circuit, then replace the old CAUTIONS places with too much dust or the possibility of water fuse with one with the same rating. • Install this unit in the console of your car. splashing. • Insulate unconnected wires with vinyl tape or other • Do not touch the metal parts of this unit during and • Do not use your own screws. Use only the screws similar material. To prevent a short circuit, do not shortly after the use of the unit. Metal parts such as provided. If you use the wrong screws, you could remove the caps and do not let the cable out at the the heat sink and enclosure become hot. damage the unit. ends of the unconnected wires or the terminals. • When parking at a low ceiling area, turn off the unit • After the unit is installed, check whether the brake • Secure the wires with cable clamps and wrap vinyl to store the antenna. As when the unit is installed in lamps, blinkers, wipers, etc. on the car are working tape around the wires that comes into contact with the car with the function of auto antenna; the radio properly. metal parts to protect the wires and to prevent short antenna extends automatically when you turn on • Do not press hard on the panel surface when circuit. the unit with the power control wire connected. installing the unit to the car. Otherwise scratches, • Connect the speaker wires correctly to the terminals (Page 41) damage, or failure may result. to which they correspond. The unit may be damaged • If the power is not turned on (“Miswiring DC Offset or fail to work if you share the · wires or ground Error”, “Warning DC Offset Error” is displayed), them to any metal part in the car. the speaker wire may have a short circuit or have • When only two speakers are being connected to the touched the chassis of the car and the protection system, connect both connectors either to the front function may have been activated. In this case, the output terminals or to the rear output terminals (do speaker wire should be checked. not mix front and rear). For example, if you connect the ª connector of the left speaker to a front output terminal, do not connect the · connector to a rear output terminal.

38 ENGLISH

EN_DDX2018TC_E.indb 38 2017/11/29 15:51 Installation and Connection

Parts list for installation Installation procedure Installing the unit Note: This parts list does not include all the package 1 Remove the key from the ignition and Installing the unit using the mounting contents. · ¥ Wiring harness (× 1) disconnect the battery. sleeve ø Extension parking cable, 2 m (× 1) 2 Make the proper input and output wire π Trim plate (× 1) connections for each unit. [ Mounting sleeve (× 1) [ “ Extraction keys (× 2) 3 Connect the speaker wires of the wiring ] Microphone, 3 m (× 1) harness. 4 Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5 Take Connector A on the wiring harness and connect it to the external power Bend the tabs of the mounting sleeve with a connector in your vehicle. screwdriver or similar utensil and attach it in place. 6 Connect the wiring harness to the unit. Installing the trim plate 7 Install the unit in your car. Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (e.g., the π sound may skip). 8 Reconnect the · battery. 9 Configure . (Page 5)

ENGLISH 39

EN_DDX2018TC_E.indb 39 2017/11/29 15:51 Installation and Connection

Removing the unit 3 Remove the unit by inserting the two Connecting external components extraction keys (“), then pulling them as 1 Engage the catch pins on the extraction illustrated. keys (“) and remove the two locks on the lower part of the trim plate (π). “ π Catch Lock

“ Be careful to avoid injury from the catch pins on 1 Steering wheel remote controller input (REMO-IN) the extraction key. • Connect to the car’s steering remote harness 2 Remove from the upper two catches of using the steering wheel remote input cable the trim plate (π). (optional accessary). Contact your KENWOOD dealer for details. 2 Audio video input (AV-IN) 3 Video output (V-OUT) 4 Rear view camera input (R-CAM) 5 Output terminals* • Left output (White) • Right output (Red) The frame can be removed from the top side in the REAR: Rear speaker preouts same manner. FRONT: Front speaker preouts SW: Subwoofer preouts For 3-way crossover: REAR: Tweeter preouts FRONT: Mid range speaker preouts SW: Woofer preouts * When connecting an external amplifier, connect its ground wire to the chassis of the car; otherwise the unit may be damaged.

40 ENGLISH

EN_DDX2018TC_E.indb 40 2017/11/29 15:51 Installation and Connection

Wiring connection

10 A fuse * For 3-way speaker system ] connection, see page 40.

Connect the antenna cord to the aerial terminal. ¥ USB input terminal (1 m) Purple with white stripe REVERSE To the car’s reverse lamp harness when using the optional rear view camera Light green To the car’s parking brake detection switch harness PRK SW Extension wire ( ø ) (For best safety, be sure to connect the parking sensor.) Light blue with yellow stripe To the remote adapter (not supplied) which is compatible with your car Blue with white stripe (output A) To the power control terminal when using the optional power amplifier (Or) To the aerial control terminal in the vehicle Brown Not used. Yellow (Battery wire)

Red (Ignition wire) Connecting the ISO connectors Pin Color and Function You may need to modify the wiring of the supplied A4 Yellow : Battery wiring harness as illustrated below. Red (A7) A5 Blue/White (output B) : Power control Red A6 Orange/White : Dimmer Yellow (A4) (Ignition wire) Red (A7) A7 Red : Ignition (ACC) Connector A Unit Vehicle A8 Black : Ground connection Connector A ] [ Yellow Yellow (A4) B1/B2 Purple / Purple/Black : Right speaker (Rear/Tweeter*) Connector B ] [ (Battery wire) B3/B4 Gray / Gray/Black : Right speaker (Front/Mid Range*) ] [ Note: Total output for blue with white stripe wires (output A + B5/B6 White / White/Black : Left speaker (Front/Mid Range*) Connector B ] [ output B) is 12 V 350 mA. Default wiring B7/B8 Green / Green/Black : Left speaker (Rear/Tweeter*) ENGLISH 41

EN_DDX2018TC_E.indb 41 2017/11/29 15:51 References

Maintenance • This unit can show or display the following: Video files – Tag: • This unit can play back the following files with Cleaning the unit MP3: ID3 Tag (version 1.0/1.1/2.2/2.3/2.4) following codec and extension code: • Do not use any solvent (for example, thinner, WMA Tag – MPEG1/MPEG2 (.mpg, .mpeg), MPEG4 (.mp4, .m4v), benzine, etc.), detergent, or insecticide. This may WAV Tag H.264 (.mp4, .m4v, .avi, flv, f4v), WMV (.wmv)*, MKV damage the monitor or the unit. AAC Tag (.mkv) • Gently wipe the panel with a soft, dry cloth. FLAC Tag • Streams that conform to: – Jacket picture: – Audio: MP3 or Dolby Audio More information Picture size: 32 × 32 to 1 232 × 672 resolution – MPEG1/MPEG2: Data size: less than 500 KB Audio: MPEG1 Audio Layer-2 or Dolby Audio About playable files File type: JPEG/PNG/BMP Video: MPEG system/program stream • This unit cannot play back the following files: • Other playable conditions: Audio files – MP3 files encoded with MP3i and MP3 PRO format. – MPEG1/MPEG2: File format: MP@ML (Main Profile at • This unit can play back the following files with – MP3 files encoded with Layer 1/2. Main Level)/SP@ML (Simple Profile at Main Level)/ following codec and extension code: – WMA files encoded with lossless, professional, and MP@LL (Main Profile at Low Level) – MP3 (.mp3), WMA (.wma), WAV (.wav), AAC (.m4a), voice format. – Video output format: NTSC (by default) FLAC (.flac) – WMA files which are not based upon Windows • This unit can playback a file with the size less than • This unit can play back files that meet the conditions Media® Audio. 4 GB. below: – WMA/AAC files copy-protected with DRM. – Bit Rate: * Maximum resolution: 640 × 480 – AAC files copy-protected with FairPlay (except MP3/WMA/AAC: 8 kbps – 320 kbps those stored on an iPod/iPhone). – Sampling Frequency: – Files which have data such as AIFF, ATRAC3, etc. MP3/WMA/AAC: 16 kHz – 48 kHz WAV/FLAC: 16 kHz – 96 kHz – Files recorded in VBR (variable bit rate), and have a discrepancy in elapsed time indication

42 ENGLISH

EN_DDX2018TC_E.indb 42 2017/11/29 15:51 References

About USB playback • Electrostatic shock at connecting a USB device may iPod/iPhone that can be connected cause abnormal playback of the device. In this case, • Made for Important disconnect the USB device then reset this unit and – iPod nano (7th Generation)* Make sure all important data has been backed up to the USB device. – iPod touch (6th Generation) avoid losing the data. • Do not pull out and connect the USB device – iPod touch (5th Generation) We bear no responsibility for any loss of data stored in repeatedly while “Reading” is shown on the screen. – iPhone 7 Plus the devices while using this unit. • Operation and power supply may not work as – iPhone 7 intended for some USB devices. – iPhone SE Playable files on a USB device • Do not leave a USB device in the car, or expose to – iPhone 6S Plus • This unit can play the following types of files stored direct sunlight or high temperatures to prevent – iPhone 6S in a USB mass storage class device. deformation or damage to the device. – iPhone 6 Plus – MPEG1/MPEG2/MPEG4/H.264/WMV/MKV/MP3/ – iPhone 6 WMA/WAV/AAC (.m4a)/FLAC Unplayable USB device – iPhone 5S • This unit can recognize: • This unit may not play back files in a USB device – iPhone 5C – A total of 5 000 files properly when using a USB extension cable. – iPhone 5 – 250 folders for video files and a maximum of 9 999 • USB devices equipped with special functions such as * Available only when connecting via USB input terminal. files per folder data security functions cannot be used with the unit. – 250 folders for photo files and a maximum of 9 999 • Do not use a USB device with 2 or more partitions. Notes on using an iPod/iPhone files per folder • Depending on the shape of the USB devices and – 9 999 folders for audio files and a maximum of • When operating an iPod/iPhone, some operations connection ports, some USB devices may not be may not be performed correctly or as intended. In 1 000 files per folder attached properly or the connection might be loose. • The maximum number of characters (when the this case, visit the following KENWOOD web site: • This unit may not recognize a memory card inserted characters are 1 byte): into a USB card reader. – Folder names: 50 characters • When you turn on this unit, the iPod/iPhone is – File names: 50 characters charged through the unit. About iPod/iPhone • The text information may not be displayed correctly. Important • For some iPod/iPhone models, the performance may Notes on using a USB device Make sure all important data has been backed up to be abnormal or unstable during operation. In this • Avoid using the USB device if it might affect driving avoid losing the data. case, disconnect the iPod/iPhone device, then check safety. We bear no responsibility for any loss of data stored in its condition. • When connecting with a USB cable, use a USB 2.0 the devices while using this unit. If the performance is not improved or slow, reset cable. your iPod/iPhone.

ENGLISH 43

EN_DDX2018TC_E.indb 43 2017/11/29 15:51 Troubleshooting

What appears to be trouble is not always serious. “Learning Process Failed” appears. iPod/iPhone Check the following points before calling a service  Your steering remote controller is not compatible, No sound comes out of the speakers. center. learning may not be completed. Consult your car  Disconnect the iPod/iPhone, then connect it again. • For operations with external components, refer also audio dealer for details.  Select another source, then reselect “iPod”. to the instructions supplied with the adapters used “Panel Mecha Error” appears: The iPod/iPhone does not turn on or does not for connection (as well as the instructions supplied  The panel does not work properly. Turn off and on work. with the external components). the unit.  Check the connection. General  Update the firmware version. USB  Charge the battery. No sound comes out of the speakers. “Reading” does not disappear from the screen.  Reset the iPod/iPhone.  Adjust the volume to the optimum level.  Turn the power off and on again. Sound is distorted.  Check the cords and connections. While playing a track, sound is sometimes  Deactivate the equalizer either on this unit or the No picture is displayed on the screen. interrupted. iPod/iPhone.  Turn on the screen. (Page 4)  The tracks are not properly copied into the USB A lot of noise is generated. The remote controller* does not work. device. Copy the tracks again, and try again.  Turn off (uncheck) “VoiceOver” on the iPod/ iPhone.  Replace the battery. Tracks are not played back as you have intended For details, visit . * Purchase optional remote controller, KNA-RCDV331. them to play. No operations are available when playing back a Playback order may differ from the one played back “No Signal”/“No Video Signal” appears.  track containing artwork. using other players.  Start playback on the external component  Operate the unit after the artwork has loaded. connected to the AV-IN input terminal. The source does not change to “USB” when you “Authorization Error” appears.  Check the cords and connections. connect a USB device while listening to another  Check whether the connected iPod/iPhone is  Signal input is too weak. source or “USB Device Error” appears when you compatible with this unit. (Page 43) connect a USB device. “Miswiring DC Offset Error”/“Warning DC Offset The USB port is drawing more power than the Error” appears.  WebLink™ design limit.  A speaker cord has shorted or it has come into Turn the power off and unplug the USB device. contact with the car chassis. Wire or insulate the  WebLink™ cannot be started. Then, turn on the power and reattach the USB speaker cord as appropriate, then reset the unit.  Check whether the latest version of WebLink™ App device. is installed on the connected smartphone. “Parking off” appears.  If the above does not solve the problem, turn  Check the connection.  No playback picture is shown when the parking the power off and on (or reset the unit) before  Charge the battery. brake is not engaged. replacing with another USB device.  Reset the smartphone.  Reconnect your smartphone.

44 ENGLISH

04_DDX_2018TC_E_Body02.indd 44 12/10/2018 5:00:28 PM Troubleshooting

Radio Bluetooth The unit does not respond when you try to copy the phonebook to the unit. AME automatic presetting does not work. Phone sound quality is poor. → You may have tried to copy the same entries (as → Store stations manually. (Page 16) → Reduce the distance between the unit and the stored) to the unit. Static noise while listening to the radio. Bluetooth mobile phone. “Connection Error” appears. → Connect the antenna firmly. → Move the car to a place where you can get a better signal reception. → The device is registered but the connection has failed. Connect the registered device. (Page 21) AV-IN The sound is interrupted or skipped while using a Bluetooth audio player. “Please Wait...” appears. No picture appears on the screen. → Reduce the distance between the unit and the → The unit is preparing to use the Bluetooth function. → Turn on the video component if it is not on. Bluetooth audio player. Disconnect the device If the message does not disappear, turn off and → Connect the video component correctly. connected for Bluetooth phone. turn on the unit, then connect the device again (or → Turn off, then turn on the unit. reset the unit). Spotify (When the sound is not yet restored) connect the “No Voice Device” appears. player again. The connected mobile phone does not have a “Check App” appears. → voice recognition system. → The Spotify application on the connected device The connected audio player cannot be controlled. has not started up. → Check whether the connected audio player “No Data” appears. → The Spotify application is not installed on the supports AVRCP (Audio/Video Remote Control → No phonebook data is contained in the connected connected device. Profile). Bluetooth phone. → Reconnect your smartphone. The Bluetooth device does not detect the unit. “Initialise Error” appears. → Restart Spotify application. → Search from the Bluetooth device again. → The unit has failed to initialize the Bluetooth “Please login or sign up.” appears. The unit does not pair with the Bluetooth device. module. Try the operation again. → You have not been signed into Spotify. → For devices compatible with Bluetooth 2.1: “Dial Error” appears. “Please check internet connection.” appears. Register the device using a PIN code. (Page 20) → Dialing has failed. Try the operation again. For devices compatible with Bluetooth 2.0: → Check the internet connection. → “Hung Up Error” appears. Enter the same PIN code for both the unit and “Unable to start Spotify.” appears. → The call has not ended yet. Park your car, and use target device. If the PIN code of the device is not Restart Spotify application. the connected mobile phone to end the call. → indicated in its instructions, try “0000” or “1234.” → Spotify application cannot be started or played in → Turn off, then turn on the Bluetooth device. “Pick Up Error” appears. current condition. → The unit has failed to receive a call. Echo or noise occurs. “Please update the Spotify app on the phone.” → Adjust the microphone unit position. appears. → Adjust the echo volume or noise reduction volume. The Spotify application on the connected device is → (Page 22) not the latest version. Update the application.

ENGLISH 45

EN_DDX2018TC_E.indb 45 2017/11/29 15:51 Specifications

Monitor section USB interface section Bluetooth section Picture Size (W × H) 6.95 inches (diagonal) wide USB Standard USB 2.0 Full Speed/High Speed Technology Bluetooth 3.0 156.6 mm × 81.6 mm Compatible Device Mass Storage Class Frequency 2.402 GHz to 2.480 GHz Display System Transparent TN LCD panel File System FAT 16/FAT 32/NTFS Output Power +4 dBm (MAX), 0 dBm (AVE), Drive System TFT active matrix system Power Class 2 Maximum Power DC 5 V 1.5 A (× 1) Number of Pixels 1 152 000 Supply Current Maximum Line of sight approx. 10 m (800H × 480V × RGB) D/A Converter 24 bit Communication (32.8 ft) Range Effective Pixels 99.99% Audio Decoder MP3/WMA/AAC (.m4a)/WAV/ Pixel Arrangement RGB striped arrangement FLAC Audio Codec SBC/AAC Back Lighting LED Video Decoder MPEG1/MPEG2/MPEG4/ Profile HFP (Hands Free Profile) 1.6 H.264/WMV/MKV A2DP (Advanced Audio Distribution Profile) 1.3 Frequency 96 kHz Sampling: AVRCP (Audio/Video Remote Response 20 Hz to 20 000 Hz Control Profile) 1.5 48 kHz Sampling: GAP (Generic Access Profile) 20 Hz to 20 000 Hz PBAP (PhoneBook Access 44.1 kHz Sampling: Profile) 1.2 20 Hz to 20 000 Hz SDP (Service Discovery Profile) Total Harmonic 0.020% (1 kHz) SPP (Serial Port Profile) 1.2 Distortion Signal to Noise Ratio 104 dB Dynamic Range 90 dB

46 ENGLISH

EN_DDX2018TC_E.indb 46 2017/11/29 15:51 Specifications

FM tuner section Video section 2 Way X'Over Tweeter: Gain (dB): Frequency Range 87.5 MHz to 108.0 MHz Color System of NTSC/PAL –8/–7/–6/–5/–4/–3/–2/–1/0 (50 kHz) External Video Input Front/Rear (HPF): Frequency (Hz): Usable Sensitivity 6.2 dBf (0.56 μV/75 Ω) External Video Input 1 Vp-p/75 Ω Through/30/40/50/60/70/ (S/N: 30 dB, Dev. Level (mini jack) 80/90/100/120/150/180/ 22.5 kHz) External Audio Max 2 V/25 kΩ 220/250 Quieting Sensitivity 15.2 dBf (1.58 μV/75 Ω) Input Level (mini Slope (dB/Oct.): (DIN S/N: 46 dB, jack) −6/−12/−18/−24 Dev. 40 kHz) Video Input Level 1 Vp-p/75 Ω Gain (dB): Frequency 30 Hz to 15 kHz for Rear Camera –8/–7/–6/–5/–4/–3/–2/–1/0 Response (±3.0 dB) (RCA jack) Subwoofer (LPF): Frequency (Hz): Signal to Noise Ratio 68 dB (MONO) Video Output Level 1 Vp-p/75 Ω 30/40/50/60/70/80/90/100/ Selectivity > 80 dB (RCA jack) 120/150/180/220/250/ (±400 kHz) Through Stereo Separation 40 dB (1 kHz) Slope (dB/Oct.): Audio section −6/−12/−18/−24 Maximum Power 50 W × 4 Phase: LW tuner section (Front & Rear) Phase Inversion: Off/On Gain (dB): Full Bandwidth 22 W × 4 (at less than 1% THD) Frequency Range 153 kHz to 279 kHz (9 kHz) –8/–7/–6/–5/–4/–3/–2/–1/0 Power (Front & Rear) Usable Sensitivity 45 μV Preout Level 4 V/10 kΩ Preout Impedance ≤ 600 Ω MW tuner section Speaker Impedance 4 Ω to 8 Ω Frequency Range 531 kHz to 1611 kHz (9 kHz) Equalizer Band: 13 Band Usable Sensitivity 28.5 μV Frequency (Hz): 62.5/100/160/250/400/630/ 1k/1.6k/2.5k/4k/6.3k/10k/ 16k Gain (dB): –9/−8/−7/−6/−5/−4/−3/−2/ −1/0/1/2/3/4/5/6/7/8/9

ENGLISH 47

EN_DDX2018TC_E.indb 47 2017/11/29 15:51 Specifications

3 Way X'Over Subwoofer (LPF): Frequency (Hz): General Tweeter (HPF): Frequency (Hz): 30/40/50/60/70/80/90/100/ Operating Voltage 14.4 V 1k/1.6k/2.5k/4k/5k/6.3k/8k/ 120/150/180/220/250/ (10.5 V to 16 V allowable) 10k/12.5k Through Slope (dB/Oct.): −6/−12 Slope (dB/Oct.): −6/−12 Maximum Current 10 A Phase: Phase: Consumption Phase Inversion: Off/On Phase Inversion: Off/On Installation With sleeve: Gain (dB): Gain (dB): Dimensions 182 mm × 111 mm × –8/–7/–6/–5/–4/–3/–2/–1/0 –8/–7/–6/–5/–4/–3/–2/–1/0 (W × H × D) 160 mm (including trim plate Mid Range (HPF): Frequency (Hz): Position 2 Way (Front/Rear/Subwoofer and sleeve) Through/30/40/50/60/70/ Delay): Without sleeve (main unit 80/90/100/120/150/180/ 0 cm to 610 cm (1.0 cm Step) installation size): 220/250 3 Way (Tweeter/Mid Range/ 178 mm × 100 mm × Slope (dB/Oct.): −6/−12 Subwoofer Delay): 162 mm 0 cm to 610 cm (1.0 cm Step) Mid Range (LPF): Frequency (Hz): Operational –10°C to +60°C Gain: −8 dB to 0 dB 1k/1.6k/2.5k/4k/6.3k/10k/ Temperature Range Subwoofer Level −50 dB to +10 dB Through Weight (Main Unit) 2.2 kg (including trim plate Slope (dB/Oct.): −6/−12 and sleeve) Phase: Phase Inversion: Off/On Gain (dB): Design and specifications are subject to change –8/–7/–6/–5/–4/–3/–2/–1/0 without notice.

48 ENGLISH

EN_DDX2018TC_E.indb 48 2017/11/29 15:51 Specifications

Trademarks and licenses • The Bluetooth® word mark and logos are registered – Redistributions of source code must retain the trademarks owned by Bluetooth SIG, Inc. and any above copyright notice, this list of conditions and • Dolby, Dolby Audio and the double-D symbol are use of such marks by JVC KENWOOD Corporation is the following disclaimer. trademarks of Dolby Laboratories. under license. Other trademarks and trade names are – Redistributions in binary form must reproduce the • “DVD Logo” is a trademark of DVD Format/Logo those of their respective owners. above copyright notice, this list of conditions and Licensing Corporation registered in the US, Japan • THIS PRODUCT IS LICENSED UNDER THE AVC PATENT the following disclaimer in the documentation and/ and other countries. PORTFOLIO LICENSE FOR THE PERSONAL USE OF A or other materials provided with the distribution. • The “AAC” logo is a trademark of Dolby Laboratories. CONSUMER OR OTHER USES IN WHICH IT DOES NOT – Neither the name of the Xiph.org Foundation • Microsoft and Windows Media are either registered RECEIVE REMUNERATION TO nor the names of its contributors may be used to trademarks or trademarks of Microsoft Corporation in (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC endorse or promote products derived from this the United States and/or other countries. STANDARD ("AVC VIDEO") AND/OR (ii) DECODE software without specific prior written permission. • “Made for iPod,” and “Made for iPhone” mean that an AVC VIDEO THAT WAS ENCODED BY A CONSUMER THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT electronic accessory has been designed to connect ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS HOLDERS AND CONTRIBUTORS “AS IS” AND ANY specifically to iPod, or iPhone, respectively, and OBTAINED FROM A VIDEO PROVIDER LICENSED TO EXPRESS OR IMPLIED WARRANTIES, INCLUDING, has been certified by the developer to meet Apple PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF performance standards. SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL MERCHANTABILITY AND FITNESS FOR A PARTICULAR Apple is not responsible for the operation of INFORMATION MAY BE OBTAINED FROM MPEG LA, PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL this device or its compliance with safety and L.L.C. SEE HTTP://WWW.MPEGLA.COM THE FOUNDATION OR CONTRIBUTORS BE LIABLE regulatory standards. Please note that the use of this • SPOTIFY and the Spotify logo are among the FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, accessory with iPod, or iPhone may affect wireless registered trademarks of Spotify AB. EXEMPLARY, OR CONSEQUENTIAL DAMAGES performance. iTunes, iPhone, iPod, iPod classic, iPod • WebLink™ is a trademark of Abalta Technologies, Inc. (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT nano, and iPod touch are trademarks of Apple Inc., • YouTube and the YouTube logo are registered OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, registered in the U.S. and other countries. trademarks of Google Inc. DATA, OR PROFITS; OR BUSINESS INTERRUPTION) • Lightning is a trademark of Apple Inc. • libFLAC HOWEVER CAUSED AND ON ANY THEORY OF • This item incorporates copy protection technology Copyright (C) 2000-2009 Josh Coalson LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, that is protected by U.S. patents and other Copyright (C) 2011-2013 Xiph.Org Foundation OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) intellectual property rights of Rovi Corporation. Redistribution and use in source and binary forms, ARISING IN ANY WAY OUT OF THE USE OF THIS Reverse engineering and disassembly are prohibited. with or without modification, are permitted provided SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF • Android is a trademark of Google Inc. that the following conditions are met: SUCH DAMAGE.

ENGLISH 49

04_DDX_2018TC_E_Body02.indd 49 12/10/2018 5:00:40 PM EN_DDX2018TC_E.indb 50 2017/11/29 15:51 EN_DDX2018TC_E.indb 51 2017/11/29 15:51 For updated information (the latest Instruction Manual, system updates, new functions, etc.), please visit the following website:

05_DDX_2018TC_E_REAR.indd 1 12/13/2018 3:29:06 PM