M-8509-30D Instruction

Total Page：16

File Type：pdf, Size：1020Kb

INS-008 Power-Plus Series® Underdrive Pulley Systems 1979-95 Mustang 5.0 Liter Part # 1513, 1528, 1553, 1554, INSTALLATION INSTRUCTIONS The BBK Street Pulley Kit is designed to increase power by reducing the overall speed of the serpen- tine system, and should in no way create a charging or cooling problem. However, an examination of the fan clutch, thermostat, and radiator should be performed to insure proper operation. (Cars equipped with high drawing aftermarket sound systems should check charging effectiveness before installation of underdrive pulleys.) Step 1 Loosen alternator nut, water pump and crank pulley bolts while belt is still in tension. (To simplify removal of the alternator pulley loosen with an air impact, with belt in place.) Step 2 Remove belt. Step 3 Bolts and three factory pulleys can now be easily removed. Step 4 Install new pulleys with bolts hand tight at this point. Install belt. Torque all bolting per factory specifications. (Use of Loctite thread lock is recommended on all threads.) NOTE A strap wrench or impact driver may be required to properly torque alternator nut Step 5 Check that belt is properly seated in all pulleys. Insure tensioner arrow is within the indicator marks on tensioner. If adjustment is required, relax tensioner from belt, loosen upper 9/16 hex alternator anchor bolt, shift alternator toward air cleaner or allow it to move in as required within the clearance of the diameters. Tighten while holding alternator. If additional adjustment is required, remove belt, loosen 3/4” nut while holding tensioner pulley. Step 6 Set warm idle speed for automatic cars at 650-700 rpm in drive. Standard shift at 750-800 rpm. www.BBKPERFORMANCE.com IMPORTANT—All appropriate safety equipment (e.i., gloves, tools) must be used during the installation of this product(s). BBK Performance, Inc. accepts no responsibility for injuries resulting in the installation of any product(s)..

Copy Link

Recommended publications

"Cheap Horses"
CHEAP HORSES CHEAP HORSES WILLKOMMEN Bienvenidos Vienvenue Welcome CHEAP HORSES CHEAP HORSES Horsepower: The rate at which work is done. A unit of power equal to 550 pound-feet per second. This is known as Imperial HP and equals 745.7 watts. Metric HP differs slightly and equals 735.5 watts. “Horsepower” is not recognized in the International System of Units (ISU) and the term horsepower, in most countries, is permitted only as a supplementary unit. The term horsepower was adopted by James Watt to compare the output of steam engines with the power of draft horses. CHEAP HORSES NEWSFLASH: Horsepower doesn’t really exist, just torque. Horsepower = (torque x engine speed) / 5252 So, horsepower is just a function of torque. FORCE: Is the pressure of one mass against POWER: Is the amount of work that can be another. In the metric system it is calculated in Newtons. done in a certain amount of time: Power = Work / Time. Gravity is an example and in our system its unit is the pound. Power was originally defined by James Watt, inventor of the steam WORK: engine. Is defined as force over distance: Work = Force x Distance. Work is achieved when a force causes an object to move. CHEAP HORSES Horsepower as a unit can be defined in many ways. Basically, it is work done in a straight line. When the work is not done in a straight line, such as with a car engine it must be defined in a different way: Torque TORQUE: Is the tendency of a force to rotate an Horsepower = (torque x RPM) / 5252 object around its axis and is defined as the force at any one point on the edge of a circle in the exact direction of rotation, multiplied by the radius (distance from the center).
[Show full text]
QUESTIONS – 4 Stroke Cycle
QUESTIONS – Engine Performance Theory Using the information in i:\wellwood\mechanics\performance.html, the internet and other sources to answer the questions below. There are NO Partial Marks - when it says “describe” – DESCRIBE This worksheet must be complete before you may work in the shop 1. Describe the relationship between Power and Longevity 2. Describe, using your own words, how the following components improve power: a. Free Flowing Air Filter b. Cold Air Intake c. High Energy Ignition d. Free Flowing exhaust e. Underdrive Pulleys f. Synthetic Fluids QUESTIONS - Engine Performance.doc 1 of 6 G Wellwood 2013 3. Sometimes an aftermarket intake manifold might reduce engine performance in part of the rpm (revolution per minute) range. How does this happen? 4. Which do you think would be better, a high-lift camshaft, or a long- duration camshaft? Why? 5. What is it about valve overlap that reduces idle quality? 6. Raising the engine's compression ratio (how much we squeeze the air/fuel charge). At some point, the fuel could be compressed so much that it explodes by itself, even before it is ignited by the spark plug (called Detonation - VERY bad for engines). How high can we realistically go in raising the compression ratio with today’s 92 octane gasoline? 7. What is the difference about the combustion chamber shape between open-chambered heads and closed-chambered heads? 8. What does a windage tray do? 9. What could go wrong if a crank scraper were improperly installed? QUESTIONS - Engine Performance.doc 2 of 6 G Wellwood 2013 10.
[Show full text]
2005 Rodware Catalog 74153G
RODWARE™ THE RODDER’S HARDWARE WHAT’S NEW! SHADOW SERIES FITTINGS . .24-26 RADIATOR HOSE . .14 SOUND AND HEAT INSULATION . .15-16 IGNITION AND DISTRIBUTORS . .17-22 AFTERBURNER SWITCHABLE COIL . .21 6A & 6AL IGNITION BOXES . .21 HURST COLLECTIBLES . .31 CONTENTS ACCESSORIES AND INTERIOR PRODUCTS . .28 AIR CLEANERS AND SCOOPS . .2-3 CHROME-PLATED FASTENERS . .12-13 COLLECTABLES AND APPAREL . .31-32 ENGINE COMPONENTS AND ACCESSORIES . .4-11 EXTERIOR PRODUCTS . .29-30 FUEL SYSTEM COMPONENTS . .23-26 IGNITION SYSTEMS AND ACCESSORIES . .17-22 RADIATOR AND HEATER HOSES . .14 SHIFTERS AND ACCESSORIES . .27 SOUND AND HEAT INSULATION . .15-16 COMPLETE INFORMATION There are about 200 products shown in this catalog. Overall, there are over 12,000 products available from the Mr. Gasket Performance Group Companies. For COMPLETE product and application information, visit your local performance specialist or visit www.mrgasket.com and download all of the Mr. Gasket Performance Group catalogs. 1 AIR CLEANERS & SCOOPS 6650B THE ORIGINAL STREET SCOOP These cast aluminum Street Scoops are fully machined and available polished or in a classic black wrinkle finish. They feature large diameter red anodized butterflies that operate off the carburetor linkage. Designed to bolt on to most stock and tunnel ram manifolds and superchargers that use two inline 4-bbl. carburetors with 5-1⁄8" diameter necks and 7-3⁄4" to 9-1⁄4" center line spacing. Also fits single 4-bbl. carburetors. Polished Black Fits most two 4-bbl. carb. set ups . .6650 . .6650B Fits most single 4-bbl. carb. set ups . .6651 . .6651B 6658 STREET SCOOP II Here’s the sequel to The Original Street Scoop.
[Show full text]
Tech, Tuning Tips & Dyno Tests
TECH, TUNING TIPS & DYNO TESTS 4.6 GT Dyno Test Summary The test vehicle was an '02 Mustang GT, 100% stock except for a cat back exhaust. The Kenne Bell Twin Screw Supercharger Kit was then added. Included in the kit is the Kenne Bell BOOST-A-PUMP®, 36 lb injectors and MONO CHIP (SWITCH CHIP® is optional $99 extra). All 3 are absolutely necessary for proper operation and tuning of this kit. PULLEY SIZE / BOOST / PULLEY RATIO / PEAK HP Add Kit Type Add Kenne Bell Add Supercharger Pulley Boost *=Standard Kits Stock Meter, Kenne Bell 90mm Meter Add 70mm Add 75mm Kenne Bell Pulley Ratio Rating 6 psi & 9 psi TB & Filter Cool Air Kit (no screen) Throttle Body Throttle Body 75mm Inlet Kit Stock - 0 - 245 250 250 250 250 250 3-7/8"* 1.67 6 Non Intercooled 351 357 361 365 365 365 3-1/2" 1.85 8 Intercooled 379 382 387 395 395 396 3-1/4"* 2.00 9 Intercooled 405 408 418 427 428 431 3-1/8" 2.08 10 Intercooled 416 422 432 442 441 449 3" 2.16 11 Intercooled 434 441 449 452 452 461 2-7/8" 2.26 12 Intercooled 447 456 469 471 470 484 2-3/4” 2.36 14 Intercooled 463 476 489 492 490 507 Note: See Catalog and Website for more info on Kenne Bell Supercharger Kits, Throttle Bodies, 90mm Meter, Cool Air Kit, Gauges, BOOST-A-SPARK™, Tech & Tuning Tips, Dyno Tests etc. NOTE: 90mm meter, 75mm throttle body and • Divide rear wheel HP above by .85 to determine engine (flywheel) HP.
[Show full text]
Edelbrock E-Force Supercharger 2007-12, GM Trucks Part # 1578 - 2007-12, 4.8/5.3L Silverado and Sierra Part # 1579 - 2007-12, 6.0/6.2L Silverado and Sierra
Edelbrock E-Force Supercharger 2007-12, GM Trucks Part # 1578 - 2007-12, 4.8/5.3L Silverado and Sierra Part # 1579 - 2007-12, 6.0/6.2L Silverado and Sierra Edelbrock Supercharger 2007-12 GM Trucks; 4.8l, 5.3l 6.0l, 6.2l Installation Instructions E-MAIL EDELBROCK YOUR STOCK VEHICLE CALIBRATION AND VEHICLE INFORMATION PLEASE COMPLETE THIS PROCEDURE PRIOR to starting the installation of your E-Force supercharger system. This will allow our calibration team to complete your calibration file while the installation of your supercharger system is being completed. Manufacturers regularly update the factory calibration, as a result, there is the possibility for delays due to not having access to your current calibration file. This can normally be resolved in 1 business day. FAILURE TO PROVIDE ALL OF THE INFORMATION BELOW WILL DELAY THE COMPLETION OF THE CALIBRATION FILE FOR YOUR VEHICLE. TO LIMIT VEHICLE DOWN TIME, PLEASE SEND US THE REQUESTED INFORMATION BEFORE STARTING THE SUPERCHARGER INSTALL. Please e-mail the requested information below to [email protected] with the E-mail Subject as “Calibration Update”. We will complete your calibration and e-mail it back to you as soon as possible. MOST calibration updates will be sent back the same business day. In rare cases, it could take up to 1-2 business days to complete. Please contact our Tech Hot Line at (800)416-8628 if you have any questions or if you need assistance with this procedure. • Begin by downloading the SCT device updater software to your computer; it can be downloaded from: http://www.sctflash.com/ software/SCTDeviceUpdater.exe • Put the vehicle into ACC mode but do not start the engine.
[Show full text]
Edelbrock E-Force Supercharger 2014-2015 CHEVY CORVETTE STINGRAY C7 LT1 6.2L Part #1570, 1571, 15700, 15701, 15702, 15710, 15711, 15712
Edelbrock E-Force Supercharger 2014-2015 CHEVY CORVETTE STINGRAY C7 LT1 6.2L Part #1570, 1571, 15700, 15701, 15702, 15710, 15711, 15712 Edelbrock E-Force Supercharger System 2014-2015 Chevy Corvette C7 LT1 6.2L Installation Instructions E-MAIL EDELBROCK YOUR STOCK VEHICLE CALIBRATION AND VEHICLE INFORMATION PLEASE COMPLETE THIS PROCEDURE PRIOR to starting the installation of your E-Force supercharger system. This will allow our calibration team to complete your calibration file while the installation of your supercharger system is being completed. Manufacturers regularly update the factory calibration, as a result, there is the possibility for delays due to not having access to your current calibration file. This can normally be resolved in 1 business day. FAILURE TO PROVIDE ALL OF THE INFORMATION BELOW WILL DELAY THE COMPLETION OF THE CALIBRATION FILE FOR YOUR VEHICLE. TO LIMIT VEHICLE DOWN TIME, PLEASE SEND US THE REQUESTED INFORMATION BEFORE STARTING THE SUPERCHARGER INSTALL. Please e-mail the requested information below to [email protected] with the E-mail Subject as “Calibration Update”. We will complete your calibration and e-mail it back to you as soon as possible. MOST calibration updates will be sent back the same business day. In rare cases, it could take up to 1-2 business days to complete. Please contact our Tech Hot Line at (800)416-8628 if you have any questions or if you need assistance with this procedure. • Begin by downloading the SCT device updater software to your computer; it can be downloaded from: http://www.sctflash.com/ software/SCTDeviceUpdater.exe • Put the vehicle into ACC mode but do not start the engine.
[Show full text]
PDF-Installation Instructions
Edelbrock Supercharger 2019-2021 GM Truck 1500 5.3L and 6.2L Excluding 2019 Silverado LD and Sierra LDT Part #15665, 15666, 156650 and 156660 WARNING! The supercharger bypass valve is factory installed and adjusted intended to be vacuum operated only. DO NOT move the solenoid actuator lever by hand or adjust the stop point. Moving the lever manually will damage the solenoid and the system will not function properly. Damage to the bypass assembly from manual movement will not be covered under manufacturer warranty. Edelbrock Supercharger System 2019-2021 GM Truck 1500 5.3L and 6.2L Installation Instructions INTRODUCTION Thank you for purchasing the Edelbrock Supercharger System for the 2019-2021 GM 1500 Trucks. This system utilizes R2650 Eaton Gen VI TVS Supercharger rotors housed inside of our Dual Pass-3 Core intercooled rotor case. Paired with bolt-on runners, and a redesigned lid, this new package will fit under the factory hood with no modifications to the stock body or hood. The supercharger features an inverted design which expels air upward and through the first pass of the intercooler. Air pressure then builds in the plenum, before being drawn down through the intercooler core another time. The supercharger is 50-state emissions legal, and includes a 3-year 36,000 mile warranty, where applicable, so there are no worries when installing on a brand new vehicle. Tuning the vehicle to specification different from those specified by Edelbrock, LLC will void the warranty, may cause engine damage, and will make the vehicle no longer compliant
[Show full text]
C07-35227 EMP, Page 1-24 @ Normalize
For over 25 years, Stewart Components has been a recognized leader in high-flow cooling system technology, and is currently developing the next generation of high efficiency advanced mechanical and electric water pumps and cooling system components. Stewart Components combines engineering expertise and advanced product development to bring forth innovative solutions. Stewart water pumps are the #1 choice of professional engine builders, race teams and performance enthusiasts, from street rodding and OEM replacement applications, to the most extreme forms of motorsports in the world. High Flow Water Pump Features: • High Strength Castings • Less Horsepower Consumption • More Efficient Impeller • Heavy Duty Bearing and Hub • Hand Assembled • One Year Guarantee BMW Pump — Page 4 Ford 4.6 Pump — Page 5 Pro Series Pumps — Pages 6-7 Chevy - Stages 1-4 — Pages 8-11 Ford - Stages 1-4 — Pages 12-13 Chrysler - Stage 1 — Page 14 Marine - Stage 1 — Page 14 Stage 4 Flow Charts — Page 15 Electric Water Pumps — Pages 16-18 Electric Fan — Page 19 Accessories — Page 20 Tech Tips — Pages 21-23 A special thanks to Richard Childress Racing, Detroit Speed & Engineering and Robert Yates Racing for use of their photos in our catalog. 2 EMP/Stewart Components 906.789.2816 | 906.233.0305 FAX | 336.859.2555 TECH Stewart Components is an industry leader in high performance automotive cooling system research and development. For over 25 years, Stewart water pumps have been the #1 choice for professional engine builders, race teams, and performance enthusiasts, from street rodding and OEM replacement applications, to the most extreme forms of motorsports in the world.
[Show full text]
Car Classification Worksheet Please Fill This out and Bring It to the Event
Car Classification Worksheet Please fill this out and bring it to the event Modification Description Yes Stock STS STX SP SM (Did you do the following to your car?) or No Legal Legal Legal Legal Legal Changed Rim Diameter? No Yes Yes Yes Yes Tires Wider than 225? n/a No No Yes Yes Tire Treadwear Rating of 140 or less? n/a No No n/a n/a R Compound Tires (eg: Hoosier, Kuhmo V700, A032R)? Yes No No Yes Yes How Wide Are Your Wheels? Stock 7.5" 8.0" n/a n/a Changed Front Sway Bar? Yes Yes Yes Yes Yes Changed Rear Sway Bar? No Yes Yes Yes Yes Changed Spring Rates? No Yes Yes Yes Yes Installed Camber Plates? No Yes Yes Yes Yes Installed Front or Rear Shock Tower Brace? No Yes Yes Yes Yes Installed Shocks With Adjustable Valving? Yes Yes Yes Yes Yes Replaced Struts with Coil-Over Suspension? No Yes Yes Yes Yes Changed Sway Bar Bushing Material? F Only Yes Yes Yes Yes Changed Suspension Bushing Material or Offset? No Yes Yes Yes Yes Added Track Bar or Panhard Bar? No Yes Yes Yes Yes Did You Lower Your Car? No Yes Yes Yes Yes Changed Diameter of Brake Rotors? No No Yes Yes Yes Installed Drilled or Slotted Brake Rotors? No Yes Yes No Yes Installed Other than Stock Proportioning Valve? No No No Yes Yes All Engine Changes Must be Emissions Legal? Yes Yes Yes No No Changed ECU Software, Chip or VTEC Controller? No Yes Yes Yes Yes Changed Boost Controls or Levels? No No No No Yes Changed Air Filter Element In Stock Airbox? Yes Yes Yes Yes Yes Changed Air Filter Enclosure (eg: Installed a Cone Filter)? No Yes Yes Yes Yes Installed Larger Throttle Body?
[Show full text]
LS3 Camaro E-Force Supercharger.Qxp
Edelbrock 2010 Camaro SS Supercharger Part #1596, #1597, #1598 & #1599 Edelbrock E-Force Supercharger System for the 2010 Camaro SS Installation Instructions INTRODUCTION Thank you for purchasing the Edelbrock 6.2L GM Supercharger System for the 2010 Chevy Camaro. The Edelbrock E- Force Supercharger System for the 2010 Camaro SS utilizes Eaton’s new Gen VI TVS Supercharger rotors, featuring a four lobe design with a full 160 deg. of twist for maximum flow, minimum temperature rise, quiet operation, and the reliability for which Eaton is known. The Edelbrock Supercharger is a complete system that maximizes efficiency and performance by minimizing air restriction into, and out of, the supercharger. This results in maximum airflow, with minimal temperature rise and power consumption. The supercharger housing itself is integrated into the intake manifold for a seamless design with minimal components, eliminating the possibility of vacuum leaks between gasket surfaces. The system also utilizes a front drive, front inlet configuration giving it the shortest, least restrictive inlet path on the market. The supercharger is inverted, expelling the air upward. Air pressure then builds in the plenum, before being drawn down through each of two intercooler cores, oriented horizontally, next to, and below the supercharger outlet. After passing through the intercooler cores, the air travels through the long 12” individual intake runners, which route underneath the supercharger housing to the cylinder head ports, in a horizontal, nested configuration. The upper plenum area is enclosed by a top cover that has been designed to provide an appealing and distinctive under-hood appearance. This configuration allows for a compact package that can fit under the stock hood and cowl of the Camaro, without sacrificing runner length, or intercooler area.
[Show full text]
SLP Performance Engine Parts Catalog
About SLP Providing OEM-quality performance, handling and SLP’s stainless steel cat- back exhaust system, appearance components for late model Detroit- based SLP’s high-flow intake runners, SLP’s cold air Performance Cars (Camaro, Corvette, Mustang, induction system and an SLP revised PCM E-Prom. Challenger and Charger) and Full-Size GM Trucks and Installing this package on a TPI 350 CID engine- SUVs is what SLP is all about. equipped 1988 Camaro resulted in a 50 horsepower gain, a one full second reduction in 0-60 MPH Prior to forming SLP and dating back to 1970, Ed times, a 6 MPH increase in top speed, and a 2 mile Hamburger first became well known for his per gallon improvement in highway fuel economy. unique product line of performance engine components, The next milestone for SLP was the addition of developed exclusively for small block Chrysler-equipped limited production specialty vehicles to the already race car applications. His company was also one of the impressive line of performance parts. SLP’s initial first Chrysler Direct Connection Performance Parts efforts were rewarded with the GM-approved 4th Distributors in the country. That company was sold in generation RPO (Regular Production Option) 1988. Camaro SS and Firebird Firehawk/WS6/Comp TA The next chapter on this interesting journey, which Specialty Vehicle programs that began in 1995. Over eventually led to forming SLP, was the creation of the next eight years SLP produced over 55,000 GM another well-known company in the Performance Parts specialty vehicles for GM and its Chevy and Pontiac Industry, Hamburger’s Oil Pans, which Ed formed in dealers, out of its 140,000 sq.
[Show full text]
LS1 Intake Manifold Part # 5004, 5005, 5006
INS-093 LS1 Intake Manifold Part # 5004, 5005, 5006 INSTALLATION INSTRUCTIONS !CAUTION! WORKING WITH FUEL SYSTEMS IS HAZARDOUS. EXTINGUISH ANY OPEN FLAMES AND IGNITION SOURCES WHEN WORK- ING WITH GASOLINE AND VAPORS. ALWAYS USE PROTECTIVE EYEWEAR. Included in this Kit: BBK intake manifold, bottom cover plate, bottom cover plate gasket, EGR block off plate, O-ring, manifold mounting bolts, split lock washers, block off plate screws, (1) valley cover plate bolt, throttle body to intake gasket, MAP sensor hold down screw (5005-5006 includes BBK throttle body). Tools Required: _” Ratchet 8mm and 10mm Short Sockets 3” Extension Flat Head Screwdriver Swivel Adjustable Pliers Silicone or Teflon Tape 3/8” Fuel Line Disconnect Tool (Spring Lock Type) Step 2 Step 1 Disconnect negative (–) battery terminal, and remove intake hose and air filter box. On Corvette models remove decorative covers by removing the oil filler cap and gently lifting the cover. After the cover has been removed replace oil cap to keep objects and debris from contaminating the oil. NOTE Fuel system may be under pressure. Use extreme caution when releasing pressure. Extinguish all open flames and ignition sources. Step 3 Step 2 Carefully release any fuel system pressure by removing the cap at the front end of the driver side fuel rail and depressing the schrader valve using a small screwdriver while shrouding the valve with a rag or cloth. Step 3 Using the 3/8 spring lock tool, disconnect the fuel rail feed hose. Step 4 Unclip the wiring harness from the fuel rails and disconnect the wiring harness from each of the fuel injectors by squeezing the spring clips, follow the harness forward and disconnect from the purge solenoid, throttle body and throttle position sensor.
[Show full text]