(I) - Band Noncoherent Radar Transponder Performance Specification Standard

Total Page:16

File Type:pdf, Size:1020Kb

(I) - Band Noncoherent Radar Transponder Performance Specification Standard Standard 262-14 Electronic Trajectory Measurements Group C (G) - BAND & X (I) - BAND NONCOHERENT RADAR TRANSPONDER PERFORMANCE SPECIFICATION STANDARD ABERDEEN TEST CENTER DUGWAY PROVING GROUND REAGAN TEST SITE WHITE SANDS MISSILE RANGE YUMA PROVING GROUND NAVAL AIR WARFARE CENTER AIRCRAFT DIVISION NAVAL AIR WARFARE CENTER WEAPONS DIVISION NAVAL UNDERSEA WARFARE CENTER DIVISION, KEYPORT NAVAL UNDERSEA WARFARE CENTER DIVISION, NEWPORT PACIFIC MISSILE RANGE FACILITY 30TH SPACE WING 45TH SPACE WING 96TH TEST WING 412TH TEST WING ARNOLD ENGINEERING DEVELOPMENT COMPLEX NATIONAL AERONAUTICS AND SPACE ADMINISTRATION DISTRIBUTION A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED This page intentionally left blank. STANDARD 262-14 C (G) - BAND & X (I) - BAND NONCOHERENT RADAR TRANSPONDER PERFORMANCE SPECIFICATION STANDARD June 2014 Prepared by Electronic Trajectory Measurements Group Transponder Ad-Hoc Committee Range Commanders Council Published by Secretariat Range Commanders Council White Sands Missile Range New Mexico 88002-5110 This page intentionally left blank. C (G) - Band & X (I) - Band Noncoherent Radar Transponder Performance Specification Standard RCC Standard 262-14, June 2014 Table of Contents Preface ........................................................................................................................................... ix Acknowledgments ........................................................................................................................ xi Acronyms .................................................................................................................................... xiii Chapter 1 Introduction ........................................................................................................ 1-1 1.1 General ............................................................................................................................. 1-1 1.2 Scope ................................................................................................................................ 1-1 1.3 Purpose ............................................................................................................................. 1-2 1.4 Order of Precedence ......................................................................................................... 1-2 1.5 Requirements and Specified Frequency ........................................................................... 1-2 1.6 Background ...................................................................................................................... 1-2 1.7 Description of Test Types ................................................................................................ 1-3 Chapter 2 Noncoherent Transponder Specifications........................................................ 2-1 2.1 Electrical Characteristics ................................................................................................. 2-1 2.1.1 Power Supply ....................................................................................................... 2-1 2.1.2 Input Voltage ....................................................................................................... 2-1 2.1.3 Isolation................................................................................................................ 2-1 2.1.4 Input Current ........................................................................................................ 2-1 2.1.5 Fuses and Circuit Breakers .................................................................................. 2-1 2.1.6 Transient Protection ............................................................................................. 2-1 2.1.7 Under-Voltage/Over-Voltage Protection ............................................................. 2-1 2.1.8 In-rush Current Limits ......................................................................................... 2-2 2.2 Identification .................................................................................................................... 2-2 2.3 Technical Data ................................................................................................................. 2-2 2.4 Mechanical Construction ................................................................................................. 2-2 2.4.1 Maximum Weight ................................................................................................ 2-2 2.4.2 Physical Size ........................................................................................................ 2-2 2.4.3 Connector Location .............................................................................................. 2-4 2.4.4 Finish.................................................................................................................... 2-4 2.4.5 Power Connectors ................................................................................................ 2-4 2.4.6 Radio Frequency Connectors ............................................................................... 2-5 2.4.7 Pressurization ....................................................................................................... 2-5 2.4.8 Case Design ......................................................................................................... 2-5 2.4.9 Shock Mounts ...................................................................................................... 2-5 2.4.10 Component Mounting .......................................................................................... 2-5 2.4.11 Orientation ........................................................................................................... 2-5 2.4.12 Test Points ............................................................................................................ 2-5 2.4.13 Special Tools ........................................................................................................ 2-5 iii C (G) - Band & X (I) - Band Noncoherent Radar Transponder Performance Specification Standard RCC Standard 262-14, June 2014 2.5 Receiver Section .............................................................................................................. 2-5 2.5.1 Frequency Range ................................................................................................. 2-5 2.5.2 Bandwidth ............................................................................................................ 2-5 2.5.3 Image Rejection ................................................................................................... 2-6 2.5.4 Frequency Stability .............................................................................................. 2-6 2.5.5 Sensitivity ............................................................................................................ 2-6 2.5.6 Interrogations ....................................................................................................... 2-6 2.5.7 Random Triggering .............................................................................................. 2-6 2.5.8 Input Impedance................................................................................................... 2-7 2.5.9 Maximum Input Signal Level .............................................................................. 2-7 2.6 Transmitter Section .......................................................................................................... 2-7 2.6.1 Frequency Range ................................................................................................. 2-7 2.6.2 Frequency Stability .............................................................................................. 2-7 2.6.3 Peak Power Output .............................................................................................. 2-7 2.6.4 Pulse Repetition Frequency ................................................................................. 2-7 2.6.5 Pulse Width .......................................................................................................... 2-7 2.6.6 Transmitter Spectrum........................................................................................... 2-8 2.6.7 Load Voltage Standing Wave Ratio .................................................................... 2-8 2.6.8 Transponder Delay ............................................................................................... 2-8 2.6.9 Recovery Time ..................................................................................................... 2-9 2.7 Environment Requirements ............................................................................................. 2-9 2.7.1 Electromagnetic Interference ............................................................................... 2-9 2.7.2 Environmental Test Procedures ......................................................................... 2-10 2.8 Quality Assurance Provisions ........................................................................................ 2-10 2.8.1 Workmanship ..................................................................................................... 2-10 2.8.2 Quality Assurance .............................................................................................. 2-10 2.8.3 Test Requirements ............................................................................................. 2-10 2.8.4 Inspection ..........................................................................................................
Recommended publications
  • Optical – Near-Infrared Catalog for the AKARI North Ecliptic Pole Deep field
    A&A 566, A60 (2014) Astronomy DOI: 10.1051/0004-6361/201322561 & c ESO 2014 Astrophysics Optical – near-infrared catalog for the AKARI north ecliptic pole Deep field Nagisa Oi1, Hideo Matsuhara1, Kazumi Murata1,2, Tomotsugu Goto3, Takehiko Wada1, Toshinobu Takagi1, Youichi Ohyama4, Matthew Malkan5, Myungshin Im6, Hyunjin Shim6,7, Stephen Serjeant8, and Chris Pearson8,9,10 1 Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency, Sagamihara, 252-5210 Kanagawa, Japan e-mail: [email protected] 2 Department of Space and Astronautical Science, The Graduate University for Advanced Studies, 753-8511 Yamaguchi, Japan 3 Institute of Astronomy and Department of Physics, National Tsing Hua University No. 101, Section 2, Kuang-Fu Road, Hsinchu 30013, Taiwan, R.O.C. 4 Academia Sinica, Institute of Astronomy and Astrophysics, 11F of Astronomy-Mathematics Building, National Taiwan University, No.1, Sec. 4, Roosevelt Rd, 10617 Taipei, Taiwan R.O.C. 5 Department of Physics and Astronomy, UCLA, Los Angeles, CA 90095-1547, USA 6 Department of Physics & Astronomy, FPRD, Seoul National University, Shillim-Dong, Kwanak-Gu, 151-742 Seoul, Korea 7 Department of Earth Science Education, Kyungpook National University, 702-701 Daegu, Republic of Korea 8 Astrophysics Group, Department of Physics, The Open University, Milton Keynes, MK7 6AA, UK 9 RAL Space, Rutherford Appleton Laboratory, Harwell Oxford, OX11 0QZ, UK 10 Oxford Astrophysics, Oxford University, Keble Road, Oxford OX1 3RH, UK Received 29 August 2013 / Accepted 18 March 2014 ABSTRACT ∗ Aims. We present an 8-band (u , g , r , i , z , Y, J, Ks) optical to near-infrared deep photometric catalog based on the observations made with MegaCam and WIRCam at the CFHT, and compute photometric redshifts, zp in the north ecliptic pole (NEP) region.
    [Show full text]
  • The UKIRT Infrared Deep Sky Survey ZY JHK Photometric System: Passbands and Synthetic Colours
    Mon. Not. R. Astron. Soc. 367, 454–468 (2006) doi:10.1111/j.1365-2966.2005.09969.x The UKIRT Infrared Deep Sky Survey ZY JHK photometric system: passbands and synthetic colours P. C. Hewett,1⋆ S. J. Warren,2 S. K. Leggett3 and S. T. Hodgkin1 1Institute of Astronomy, Madingley Road, Cambridge CB3 0HA 2Blackett Laboratory, Imperial College of Science, Technology and Medicine, Prince Consort Road, London SW7 2AZ 3United Kingdom Infrared Telescope, Joint Astronomy Centre, 660 North A‘ohoku Place, Hilo, HI 96720, USA Accepted 2005 December 7. Received 2005 November 28; in original form 2005 September 16 ABSTRACT The United Kingdom Infrared Telescope (UKIRT) Infrared Deep Sky Survey is a set of five surveys of complementary combinations of area, depth and Galactic latitude, which began in 2005 May. The surveys use the UKIRT Wide Field Camera (WFCAM), which has a solid angle of 0.21 deg2. Here, we introduce and characterize the ZY JHK photometric system of the camera, which covers the wavelength range 0.83–2.37 µm. We synthesize response functions for the five passbands, and compute colours in the WFCAM, Sloan Digital Sky Survey (SDSS) and two-Micron All Sky Survey (2MASS) bands, for brown dwarfs, stars, galaxies and quasars of different types. We provide a recipe for others to compute colours from their own spectra. Calculations are presented in the Vega system, and the computed offsets to the AB system are provided, as well as colour equations between WFCAM filters and the SDSS and 2MASS passbands. We highlight the opportunities presented by the new Y filter at 0.97–1.07 µm for surveys for hypothetical Y dwarfs (brown dwarfs cooler than T), and for quasars of very high redshift, z > 6.4.
    [Show full text]
  • NLTE Solar Irradiance Modeling with the COSI Code
    Astronomy & Astrophysics manuscript no. Irradiance˙COSI c ESO 2018 August 12, 2018 NLTE solar irradiance modeling with the COSI code A. I. Shapiro1, W. Schmutz1, M. Schoell1,2, M. Haberreiter3, and E. Rozanov1,4 1 Physikalisch-Meteorologishes Observatorium Davos, World Radiation Center, 7260 Davos Dorf, Switzerland e-mail: [email protected] 2 Institute for Astronomy ETH, Zurich, Switzerland 3 Laboratory for Atmospheric and Space Physics, University of Colorado, Boulder, CO 80303, USA 4 Institute for Atmospheric and Climate science ETH, Zurich, Switzerland Received 30 December 2009; accepted 29 March 2010 ABSTRACT Context. The solar irradiance is known to change on time scales of minutes to decades, and it is suspected that its substantial fluctua- tions are partially responsible for climate variations. Aims. We are developing a solar atmosphere code that allows the physical modeling of the entire solar spectrum composed of quiet Sun and active regions. This code is a tool for modeling the variability of the solar irradiance and understanding its influence on Earth. Methods. We exploit further development of the radiative transfer code COSI that now incorporates the calculation of molecular lines. We validated COSI under the conditions of local thermodynamic equilibrium (LTE) against the synthetic spectra calculated with the ATLAS code. The synthetic solar spectra were also calculated in non-local thermodynamic equilibrium (NLTE) and compared to the available measured spectra. In doing so we have defined the main problems of the modeling, e.g., the lack of opacity in the UV part of the spectrum and the inconsistency in the calculations of the visible continuum level, and we describe a solution to these problems.
    [Show full text]
  • Raman Spectroscopy of Graphene and the Determination of Layer Thickness
    Application Note: 52252 The Raman Spectroscopy of Graphene and the Determination of Layer Thickness Mark Wall, Ph.D., Thermo Fisher Scientific, Madison, WI, USA Currently, a tremendous amount of activity is being directed Key Words towards the study of graphene. This interest is driven by the novel properties that graphene possesses and its potential • DXR Raman for use in a variety of application areas that include but Microscope are not limited to: electronics, heat transfer, bio-sensing, • 2D Band membrane technology, battery technology and advanced composites. Graphene exists as a transparent two dimen- • D Band sional network of carbon atoms. It can exist as a single • G Band atomic layer thick material or it can be readily stacked to form stable moderately thick samples containing millions • Graphene of layers, a form generally referred to as graphite. The • Layer Thickness interesting properties exhibited by graphene (exceptionally large electrical and thermal conductivity, high mechanical strength, high optical transparency, etc…), however, are only observed for graphene films that contain only one or a few layers. Therefore, developing technologies and devices based upon graphene’s unusual properties requires within the carbon lattice are present). These differences, accurate determination of the layer thickness for materials although they appear subtle, supply very important infor- under investigation. Raman spectroscopy can be employed mation when scrutinized closely. There are differences in to provide a fast, non destructive means of determining the band positions and the band shapes of the G band layer thickness for graphene thin films. 2D bands and the relative intensity of these bands are also significantly different.
    [Show full text]
  • The Origin of UV / Optical Variability of AGN: Relationship to X-Ray Variability
    The origin of UV / Optical Variability of AGN: Relationship to X-ray Variability Ian McHardy University of Southampton 1 Southampton Main Questions • What drives UV/optical variability in AGN? • How is the X-ray band related to UV/optical? • What do X-ray/UV/optical variations tell us about AGN inner structure? 2 Southampton Possible drivers of UV/optical Variability - Reprocessing of higher energy photons - which “high” energy? X-ray? Far-UV? - reprocessing off what? Disc? BLR? - Intrinsic disc variations 3 Southampton Observational Diagnostics • Reprocessing - High energies lead uv/optical by short (hour-days) light travel time. Allows ‘reverberation’ mapping of reprocessing structures. Measure lag from different temperature regions (different λ ). • Intrinsic disc variability – High energies lag: two possibilities – Long lag (months), viscous propagation timescale for perturbations to reach X-ray region from optical in disc – Short lag (hour-day), light travel time of UV seed photons to corona 4 REPROCESSING Southampton Wavelength dependence of lags For standard Shakura-Sunyaev DISC, 4 −1 −3 L(R)=σT ∝MBH . m! E R dissipating gravitational potential energy ! ( R in gravitational radii) −1/4 1/4 −3/4 i.e. T ∝ M m! R BH E Disc illumination from point source, height H above disc, also falls off as H R-3 So for reprocessing 4/3 Lag ∝Wavelength (eg Cackett et al 2007) from disc, we expect and Lag ∝M2/3m! 1/3 ! E For illumination of a shell-type structure, eg the BLR or torus, Illumination falls of as R-2 giving Lag ∝Wavelength2 5 Southampton
    [Show full text]
  • 1996Aj 111.1748F the Astronomical Journal Volume 111, Number 4 April 1996 the Sloan Digital Sky Survey Photometric System M
    THE ASTRONOMICAL JOURNAL VOLUME 111, NUMBER 4 APRIL 1996 111.1748F THE SLOAN DIGITAL SKY SURVEY PHOTOMETRIC SYSTEM M. Fukugita1 Institute for Advanced Study, Princeton, New Jersey 08540 1996AJ Electronic mail: [email protected] T. Ichikawa Kiso Observatory, University of Tokyo, Kiso-gun, Nagano 397-01, Japan Electronic mail: [email protected] J. E. Gunn Princeton University Observatory, Princeton, New Jersey 08544 Electronic mail: [email protected] M. Doi AND K. Shimasaku Department of Astronomy, University of Tokyo, Tokyo 113, Japan Electronic mail: [email protected]; [email protected] D. P. Schneider Department of Astronomy, Pennsylvania State University, University Park, Pennsylvania 16802 Electronic mail: [email protected] Received 1995 September 11; revised 1995 December 20 ABSTRACT This paper describes the Sloan Digital Sky Survey photometric system, a new five-color (ufg'r'i'z') wide-band CCD system with wavelength coverage from 3000 to 11 000 Â. The zero points will be based on an updated version of the spectrophotometric AR,, system. This updated calibration, designated as A#95, is presented in this paper. © 1996 American Astronomical Society. 1. INTRODUCTION red filter centered at 7700 Â with a width of 1500 À, and z' is a near-infrared passband centered at 9100 À with a width This paper describes the photometric system to be used of 1200 Â; the shape of the z' response function at long for the Sloan Digital Sky Survey (SDSS). The zero point of wavelengths is determined by the CCD sensitivity.
    [Show full text]
  • Diagnostic of the Solar Photosphere with High Spatial Resolution Using CH, CN and Continuum Spectral Bands
    Diagnostic of the solar photosphere with high spatial resolution using CH, CN and continuum spectral bands Dissertation zur Erlangung des Doktorgrades der Mathematisch-Naturwissenschaftlichen Fakultaten¨ der Georg-August-Universitat¨ zu Gottingen¨ vorgelegt von Vasily Zakharov aus Moskau / Russland Gottingen¨ 2006 Bibliografische Information Der Deutschen Bibliothek Die Deutsche Bibliothek verzeichnet diese Publikation in der Deutschen Nationalbibliografie; detaillierte bibliografische Daten sind im Internet uber¨ http://dnb.ddb.de abrufbar. D7 Referent: Prof. Dr. F. Kneer Korreferent: Prof. Dr. S. K. Solanki Tag der mundlichen¨ Prufung:¨ 24.03.2006 Copyright c Copernicus GmbH 2006 ISBN 3-936586-54-3 Copernicus GmbH, Katlenburg-Lindau Druck: Schaltungsdienst Lange, Berlin Printed in Germany Contents Contents 3 Summary 5 1 Introduction 7 2 High resolution imaging 17 2.1 Phasediversityimagereconstruction . ..... 17 2.2 Observations ................................ 23 2.3 Datareduction................................ 25 2.3.1 Darkframeandflatfield . 25 2.3.2 JPDSreconstruction . 26 2.4 Results.................................... 27 3 High resolution spectroscopy of the solar photosphere 33 3.1 Observations ................................ 33 3.2 Datareductionofthespectra . 36 3.2.1 Darkframe ............................. 37 3.2.2 Flatfield .............................. 37 3.2.3 Dopplershiftandlinewidth . 43 3.2.4 Slitposition............................. 45 3.2.5 Intensity .............................. 46 3.2.6 BrightPointIndex ........................
    [Show full text]
  • Gaia Broad Band Photometry
    Astronomy & Astrophysics manuscript no. jordi˙15441 c ESO 2010 October 21, 2010 Gaia broad band photometry⋆ C. Jordi1,2, M. Gebran1,2, J.M. Carrasco1,2, J. de Bruijne3, H. Voss1,2, C. Fabricius4,2, J. Knude5, A. Vallenari6, R. Kohley7, A. Mora7 1 Departament d’Astronomia i Meteorologia, Universitat de Barcelona, c/ Mart´ıi Franqu`es, 1, 08028 Barcelona, Spain e-mail: carme,[email protected] 2 Institut de Ci`encies del Cosmos, ICC-UB, c/ Mart´ıi Franqu`es, 1, 08028 Barcelona, Spain 3 Research and Scientific Support Department of the European Space Agency, European Space Research and Technology Centre, Keplerlaan 1, 2201 AZ, Noordwijk, The Netherlands 4 Institut d’Estudis Espacials de Catalunya (IEEC), Edif. Nexus, C/ Gran Capit`a, 2-4, 08034 Barcelona, Spain 5 Niels Bohr Institute, Copenhagen University Juliane Maries Vej 30, DK-2100 Copenhagen Ø 6 INAF, Padova Observatory, Vicolo dell’Osservatorio 5, 35122 Padova, Italy 7 Science Operations Department of the European Space Agency, European Space Astronomy Centre, Villanueva de la Ca˜nada, 28692 Madrid, Spain Received / Accepted ABSTRACT Aims. The scientific community needs to be prepared to analyse the data from Gaia, one of the most ambitious ESA space missions, which is to be launched in 2012. The purpose of this paper is to provide data and tools to predict how Gaia photometry is expected to be. To do so, we provide relationships among colours involving Gaia magnitudes (white light G, blue GBP, red GRP and GRVS bands) and colours from other commonly used photometric systems (Johnson-Cousins, Sloan Digital Sky Survey, Hipparcos and Tycho).
    [Show full text]
  • Analyzing the Raman Spectra of Graphenic Carbon Materials from Kerogens to Nanotubes: What Type of Information Can Be Extracted from Defect Bands?
    Journal of C Carbon Research Article Analyzing the Raman Spectra of Graphenic Carbon Materials from Kerogens to Nanotubes: What Type of Information Can Be Extracted from Defect Bands? Pascal Puech 1,*, Mariem Kandara 1, Germercy Paredes 1,2 , Ludovic Moulin 3, Elsa Weiss-Hortala 3 , Anirban Kundu 1,4 , Nicolas Ratel-Ramond 1,Jérémie-Marie Plewa 1, Roland Pellenq 5 and Marc Monthioux 1 1 CEMES, UPR8011-CNRS, Université de Toulouse, 29 rue Jeanne Marvig, 31055 Toulouse CEDEX 04, France; [email protected] (M.K.); [email protected] (G.P.); [email protected] (A.K.); [email protected] (N.R.-R.); [email protected] (J.-M.P.); [email protected] (M.M.) 2 Nanoscience Research Laboratory, Pontificia Universidad Católica Madre y Maestra, Autopista Duarte km 1 1 2 , Apartado Postal 822, Santiago, Dominican Republic 3 IMT Mines Albi, Centre RAPSODEE, UMR CNRS 5302, Campus Jarlard, F-81013 Albi CEDEX 09, France; [email protected] (L.M.); [email protected] (E.W.-H.) 4 Institute of Nano Science and Technology, Habitat Center, Sector 64, Phase 10, Mohali, Punjab 160062, India 5 CNRS/MIT/Aix-Marseille Université Joint Laboratory “MultiScale Materials Science for Energy and Environment”, UMI 2, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139, USA; [email protected] * Correspondence: [email protected]; Tel.: +33-(0)5-67-52-43-57 Received: 30 September 2019; Accepted: 30 October 2019; Published: 1 November 2019 Abstract: Considering typical spectra of a broad range of carbonaceous materials from gas-shale to nanotubes, various ways by which defects show up in Raman spectra are exampled and discussed.
    [Show full text]
  • Standard Photometric Systems
    7 Aug 2005 11:27 AR AR251-AA43-08.tex XMLPublishSM(2004/02/24) P1: KUV 10.1146/annurev.astro.41.082801.100251 Annu. Rev. Astron. Astrophys. 2005. 43:293–336 doi: 10.1146/annurev.astro.41.082801.100251 Copyright c 2005 by Annual Reviews. All rights reserved STANDARD PHOTOMETRIC SYSTEMS Michael S. Bessell Research School of Astronomy and Astrophysics, The Australian National University, Weston, ACT 2611, Australia; email: [email protected] KeyWords methods: data analysis, techniques: photometric, spectroscopic, catalogs ■ Abstract Standard star photometry dominated the latter half of the twentieth century reaching its zenith in the 1980s. It was introduced to take advantage of the high sensitivity and large dynamic range of photomultiplier tubes compared to photographic plates. As the quantum efficiency of photodetectors improved and the wavelength range extended further to the red, standard systems were modified and refined, and deviations from the original systems proliferated. The revolutionary shift to area detectors for all optical and IR observations forced further changes to standard systems, and the precision and accuracy of much broad- and intermediate-band photometry suffered until more suitable observational techniques and standard reduction procedures were adopted. But the biggest revolution occurred with the production of all-sky photometric surveys. Hipparcos/Tycho was space based, but most, like 2MASS, were ground-based, dedicated survey telescopes. It is very likely that in the future, rather than making a measurement of an object in some standard photometric system, one will simply look up the magnitudes and colors of most objects in catalogs accessed from the Virtual Observatory.
    [Show full text]
  • Atp-01, Volume Ii Allied Maritime Tactical Signal and Maneuvering Book
    NATO UNCLASSIFIED ATP-01, Vol. II NATO STANDARD ATP-01, VOLUME II ALLIED MARITIME TACTICAL SIGNAL AND MANEUVERING BOOK Edition (G) Version (1) JANUARY 2016 NORTH ATLANTIC TREATY ORGANIZATION ALLIED TACTICAL PUBLICATION Published by the NATO STANDARDIZATION OFFICE (NSO) © NATO/OTAN MAY BE CARRIED IN MILITARY AIRCRAFT 0410LP1158006 I EDITION (G) VERSION (1) NATO UNCLASSIFIED NATO UNCLASSIFIED ATP-01, Vol. II ALPHABETICAL AND NUMERAL FLAGS FLAG FLAG FLAG and Spoken Writtenand Spoken Writtenand Spoken Written NAME NAME NAME MIKE ALFA A M YANKEE Y A M Y NOVEMBER BRAVO B N ZULU Z B N Z C OSCAR O 1 CHARLIE ONE C O ONE DELTAD PAPA P TWO 2 D P TWO ECHOE QUEBEC Q THREE 3 E Q THREE FOXTROTF ROMEO R FOUR 4 F R FOUR GOLFG SIERRA S FIVE 5 G S FIVE 6 HOTELH TANGO T SIX H T SIX 7 INDIAI UNIFORM U SEVEN I U SEVEN JULIETTJ VICTOR V EIGHT 8 J V EIGHT KILOK WHISKEY W NINE 9 K W NINE LIMAL XRAY X ZERO 0 L X ZERO II EDITION (G) VERSION (1) NATO UNCLASSIFIED NATO UNCLASSIFIED ATP-01, Vol. II January 2016 PUBLICATION NOTICE 1. ATP-01(G)(1), Volume II, ALLIED MARITIME TACTICAL SIGNAL AND MANEUVERING BOOK, is effective upon receipt. It supersedes ATP-01(F)(1), Volume II. 2. Summary of changes: a. Chapter 1: Updates chapter with information from MTP-01(F)(1). b. Figures 1-5, 1-6, and 1-7 updated to refl ect information from MTP-01(F)(1). c. Chapter 2: Updates Signal Flags and Pennants table.
    [Show full text]
  • G-Band Waveguide to Microstrip Transition for MMIC Integration
    Donadio, Oberdan (2012) G-band waveguide to microstrip transition for MMIC integration. PhD thesis. http://theses.gla.ac.uk/3354/ Copyright and moral rights for this thesis are retained by the author A copy can be downloaded for personal non-commercial research or study, without prior permission or charge This thesis cannot be reproduced or quoted extensively from without first obtaining permission in writing from the Author The content must not be changed in any way or sold commercially in any format or medium without the formal permission of the Author When referring to this work, full bibliographic details including the author, title, awarding institution and date of the thesis must be given Glasgow Theses Service http://theses.gla.ac.uk/ [email protected] G-band Waveguide to Microstrip Transition for MMIC Integration by Oberdan Donadio Thesis submitted in fulfilment of the requirements for the degree of Doctor of Philosophy in the School of Engineering College of Science and Engineering January 2012 Declaration of Authorship I, Oberdan Donadio, declare that this thesis titled, `G-band Waveguide to Microstrip Transition for MMIC Integration' and the work presented in it are my own. I confirm that: This work was done wholly or mainly while in candidature for a research degree at the University of Glasgow. Where any part of this thesis has previously been submitted for a degree or any other qualification at this University or any other institution, this has been clearly stated. Where I have consulted the published work of others, this is always clearly at- tributed. Where I have quoted from the work of others, the source is always given.
    [Show full text]