T7600 Series Bacnet Multi-Stage Thermostats with and Without Scheduling Capability

1 T7600 Series BACnet Multi-Stage Thermostats With and Without Scheduling Capability

Product overview The T7600 series BACnet communicating single stage and multi-stage communicating thermostat has been specifically designed to control packaged and split HVAC equipment on a BACnet MS-TP® network. The product is available with and without scheduling capability and features an intuitive, menu- driven, backlit LCD display. Configuration can be performed directly on the thermostat, through the usage of a concealed button or via the network. All models contain two digital inputs, and, depending on the model, up to three remote sensor inputs are available. All models with scheduler contain a SPST auxiliary switch, which can be used to control lighting or disable the economizer function. For more advanced applications, an economizer control logic has been integrated onto the thermostat for use with proportional damper economizer actuators. Fig.1 - T7600 Series Models 2 Heat / 2 Cool 3 Heat / 2 Cool Application 1 Heat / 1 Cool 2 Heat / 2 Cool with economizer heat pump Model (scheduler) T7652A1000B T7652B1000B T7656B1000B T7652H1000B Model (no scheduler) T7600A1000B T7600B1000B T7605B1000B T7600H1000B

Installation

• Remove security screw on the bottom of thermostat cover.

• Open up by pulling on the bottom side of thermostat. (Fig. 3)

A) Location: • If replacing an old thermostat, label the 1- Should not be installed on an outside wall. wires before removal of the old 2- Must be installed away from any heat source. thermostat. 3- Should not be installed near an air discharge grill. • Electronic controls are static sensitive 4- Should not be affected by direct sun radiation. devices. Discharge yourself properly 5- Nothing must restrain vertical air circulation to the thermostat. before manipulation and installing the B) Installation: thermostat. 1- Swing open the thermostat PCB to the left by pressing the PCB locking • Short circuit or wrong wiring may tabs. (Fig. 4) permanently damage the thermostat or 2- Pull out cables 6” out of the wall. the equipment. 3- Wall surface must be flat and clean. • Anti-short cycling can be set to 0 4- Insert cable in the central hole of the base. minutes for equipment that posses their 5- Align the base and mark the location of the two mounting holes on the own anti cycling timer. Do not use that wall. Install proper side of base up. value unless the equipment is equipped 6- Install anchors in the wall. with such internal timer. Failure to do so 7- Insert screws in mounting holes on each side of the base. (Fig. 4) can damage the equipment. 8- Gently swing back the circuit board on the base and push on it until the • All T7600 series thermostats are to be tabs lock it. used only as operating controls. 10- Pull out the screw terminal blocks using the pull tabs on each connector. Whenever a control failure could lead to (Fig. 5) personal injury and/or loss of property, it 11- Strip each wire 1/4 inch. becomes the responsibility of the user to 12- Insert each wire according to wiring diagram. add safety devices and/or alarm system 13- Gently push back into hole excess wring (Fig. 5) to protect against such catastrophic 14- Install wiring terminals failures. 15- Reinstall the cover ( top side first ) and gently push back extra wire length into the hole in the wall. 16 Install security screw. Wiring terminals Pull out terminal blocks (model T7656B1000B)

Remove cover from bottom Location of pull tabs

Fig.3 Fig.4 Fig.5 2 Wiring

T7600A1000B & T7652A1000B Thermostat Terminals - T7652A1000B 1 Heat / 1 Cool A+ BACnet Y1 G RC C Network RH W1 A+ B- BACnet terminals B- Network terminals Ref. MS-TP MS-TP AU DI1 DI2 RS Scom OS Ref.

Digital Input #1

Jumper J1 Digital Input #2

Y1 G RC C RH W1 AU DI1 DI2 RS Scom OS

Heat Fan Stage 1 Remote Remote Room Outdoor Sensor Sensor Cool Auxiliary Stage 1 Output

24 Vac 24 Vac Field contacts Thermostat internal wiring System wiring Optional Jumper J1 T1 T2 If T2 is not used install jumper J1 across RC and RH.

T7600B1000B & T7652B1000B Thermostat Terminals - T7652B1000B A+ 2 Heat / 2 Cool BACnet Y2Y1 G RC C Network B- RH W1 W2 A+ terminals BACnet Ref. MS-TP B- Network terminals AU DI1 DI2 RS Scom OS MS-TP Ref.

Digital Input #1

Jumper J1 Digital Input #2

Y2 Y1 G RC C RH W1 W2 AU DI1 DI2 RS Scom OS

Cool Heat Auxiliary Stage 2 Fan Stage 1 Output Remote Remote Room Outdoor Sensor Sensor Cool Heat Stage 1 Stage 2

24 Vac 24 Vac Field contacts Thermostat internal wiring System wiring Optional Jumper J1 T1 T2 If T2 is not used install jumper J1 across RC and RH.

T7605B1000B & T7656B1000B Thermostat Terminals - T7656B1000B A+ 2 Heat / 2 Cool / economizer BACnet Y2 Y1 G RC C Network B- RH W1 W2 A+ terminals BACnet Ref. MS-TP B- Network terminals EC AU DI1 DI2 RS Scom OS MS MS-TP Ref.

Digital Input #1

Jumper J1 Digital Input #2

Y2 Y1 G RC C RH W1 W2 EC AU DI1 DI2 RS Scom OS MS

Cool Heat 0-10 Vdc Stage 2 Fan Stage 1 Remote Remote Room Mixed Air Sensor Sensor Cool Heat Auxiliary Stage 1 Stage 2 24V Com Output

Remote Outdoor Sensor

24 Vac 24 Vac Field contacts Thermostat internal wiring System wiring Optional Jumper J1 T1 T2 If T2 is not used install jumper J1 across RC and RH. 3

T7652H1000B & T7652H1000B Thermostat Terminals - T7652H1000B A+ Heat pump BACnet Y2 Y1 G RC C Network RH W1 O/B A+ B- BACnet terminals B- Network terminals Ref. MS-TP MS-TP AU DI1 DI2 RSScom OS Ref.

Digital Input #1

Jumper J1 Digital Input #2

Y2 Y1G RC C RH W1 O/B AU DI1 DI2 RS Scom OS

Compressor Auxiliary Auxiliary Fan Remote Remote Stage 2 Heat Output Room Outdoor Sensor Sensor Compressor Reversing Stage 1 Valve

24 Vac 24 Vac Field contacts Thermostat internal wiring System wiring Optional Jumper J1 T1 T2 If T2 is not used install jumper J1 across RC and RH.

Wiring notes: 1: If the same power source is used for the heating stages, install jumper across RC & RH. Maximum current is 2.0 amps. 2: If auxiliary output is used to toggle occupancy of the electronic control card inside the equipment, configure the relay parameter (Aux cont ) to the N.O. setting. A second relay can be added for additional functionality of the occupancy output. 3: Economizer output uses a half bridge rectifier. Reference of the control signal is the common of the power supply of the thermostat. (terminal C) 4: Electromechanical contacts are to be used with the digital inputs. Electronic triacs cannot be used as mean of switching for the input. The switched leg to the input for the input to activate is terminal C ( common ) 5: The transformer of the unit provides power to the thermostat and the additional loads that will be wired to the thermostat.

User menu flow chart:

Increase the current temperature setpoint temporarily Temporary setpoint is active for the duration fixed by TOccTime If in Auto mode, pressing the "NO" key will toggle between cooling and heating setpoints Lower the current temperature setpoint temporarily, Temporary setpoint is active for the duration fixed by TOccTime If in Auto mode, pressing the "NO" key will toggle between cooling and heating setpoints

YES Press YES key to manually change displayed information such as temperature, system mode, etc.

If status is: Override MENU Unoccupied schd Y/N

If status is: Temporary Occupied Time, Resume Occupied hold or schd Y/N Unoccupied hold

RoomTemp Sys mode Fan mode Schedule Clock Schedule Exit set? Y/N set? Y/N set? Y/N set? Y/N set? Y/N hold Y/N menu Y/N off On Resume emergenc Smart Occ Hold heat Auto Uno Hold cool auto

Time Day 12/24hrs Exit set? Y/N set? Y/N set? Y/N menu Y/N

Time Day 12 / 24

Cooling Heating Unocc CL Unocc HT °F/°C set? Y/N set? Y/N set? Y/N set? Y/N set? Y/N

Temperature Temperature Temperature Temperature °C °F

Exit Sunday Saturday Friday Thursday Wednsday Tuesday Monday menu Y/N set? Y/N set? Y/N set? Y/N set? Y/N set? Y/N set? Y/N set? Y/N

Occupied Occupied Occupied Occupied Occupied Occupied Occupied day? Y/N day? Y/N day? Y/N day? Y/N day? Y/N day? Y/N day? Y/N

Occupied Occupied Occupied Occupied Occupied Occupied Occupied 12:00 pm 12:00 pm 12:00 pm 12:00 pm 12:00 pm 12:00 pm 12:00 pm

Time Time Time Time Time Time Time

Unoccup Unoccup Unoccup Unoccup Unoccup Unoccup Unoccup 12:00 pm 12:00 pm 12:00 pm 12:00 pm 12:00 pm 12:00 pm 12:00 pm

Time Time Time Time Time Time Time 4 Programming and status display instructions 1. Status display The thermostat features a two-line, eight-character display. There is a low level back-light level that is always active and can only be seen at night. When left unattended, the thermostat has an auto scrolling display that shows the actual status of the system. Each item is scrolled one by one with the back lighting off. Pressing any key will cause the back light to come on.

Sequence of auto-scroll status display: Room Outdoor Clock status System mode Schedule status Alarms temperature temperature

RoomTemp Monday Sys mode Occupied Outdoor Service x.x °C or °F 12.00 AM auto x.x °C or°F Sys mode Occupied Frost ON off hold Sys mode Unoccup SetClock heat Sys mode Unoccup Filter cool hold Sys mode Override emergenc Manual scroll of each menu item is achieved by pressing the Up arrow ( scroll ) key repetitively. The last item viewed will be shown on the display for 30 seconds before returning to automatic scrolling. Temperature is automatically updated when scrolling is held. • Outdoor air temperature display is only enabled when outdoor air temperature sensor is connected. • A maximum range status display of 50 °C ( 122 °F ) indicates a shorted sensor. Associated functions, such as mode lockouts and economizer function are automatically disabled. • A minimum range status -40 °C ( -40 °F ) is not displayed and indicates an opened sensor or a sensor not connected. Associated functions, such as mode lockouts and economizer function are automatically disabled.

If alarms are detected, they will automatically be displayed at the end of the status display scroll. During an alarm message display, the back lit screen will light up at the same time as the message and shut off during the rest of the status display. Two alarms maximum can appear at any given time. The priority for the alarms is as follows:

Frost ON Indicates that the heating is energized by the low limit frost protection setpoint 5.6 °C ( 42 °F ) SetClock Indicates that the clock needs to be reset. There has been a power failure which has lasted longer than 6 hours Service Indicates that there is a service alarm as per one of the programmable digital input ( DI1 or DI2 ) Filter Indicates that the filters are dirty as per one of the programmable digital input ( DI1 or DI2 ) Three status LEDs on the thermostat cover are used to indicate the status of the fan, a call for heat, or a call for cooling.

Multistage and single stage models Heat pump models • When the fan is on, the FAN LED will illuminate. • When the fan is on, the FAN LED will illuminate. • When heating is on, the HEAT LED will illuminate. • When auxiliary heat is on, the AUX HEAT LED will • When cooling is on, the COOL LED will illuminate. illuminate. • When compressor is on, the HEAT-PUMP LED will illuminate.

Fig.11 - Multistage and single stage models Fig.12 – Heat pump models

2. User programming instructions menu The T7600 series of thermostat feature an intuitive, menu-driven, back-lit LCD display that walks users through the programming steps, making the programming process extremely simple. This menu is typically accessed by the user to set the parameters such as temperature and time events, system mode, fan mode, etc. It is possible to bring up the user menu at any time by depressing the MENU key. The status display automatically resumes after exiting the user-programming menu. If the user pauses at any given time during programming, Auto Help text is displayed to help and guide the user through the usage and programming of the thermostat.

Press yes key to change cooling temperature setpoint Ex.: Use the up or down arrow to adjust cooling setpoint 5 Each of the sections in the menu are accessed and programmed using 5 keys on the thermostat cover. The priority for the alarms is as follows:

The YES key is used to confirm a selection, to move onto the next menu item and to manually scroll through the displayed information.

The NO key is used when you do not desire a parameter change, and to advance to the next menu item. Can also be used to toggle between heating and cooling setpoints.

The MENU key is used to access the Main User Menu or exit the menu.

The down arrow key is used to decrease temperature setpoint and to adjust the desired values when programming and configuring the thermostat.

The up arrow key is used to increase temperature setpoint and to adjust the desired values when programming and configuring the thermostat.

When left unattended for 45 seconds, the display will resume automatic status display scrolling. To turn on the back light, press any key on the front panel. The back lit display will turn off when the thermostat is left unattended for 45 seconds

Sequence of user menu: Override Temperature System mode Fan mode setting Schedules setting Clock setting Schedule hold Resume setpoints setting Page 14 Page 14 Page 14 Page 15 Page 15-16 Page 17 Page 17 Section A/B Section C Section D Section E Section F-G Section H Section J

Override RoomTemp Sys mode Fan mode Schedule Clock Schedule schd Y/N set Y/N set Y/N set Y/N set Y/N set Y/N hold Y/N Appears only in unoccupied mode

Resume schd Y/N Appears only in override mode or schedule hold There is a default profile set in the thermostat from the factory. This enables the thermostat to operate as a non-scheduling unit in day mode operation at start up. Programmed default temperature setpoints: Programmed default modes: Occupied cooling setpoint = 24 °C ( 75 °F ) System mode = Auto Occupied heating setpoint = 22 °C ( 72 °F ) Fan mode = Auto Unoccupied cooling setpoint = 28 °C ( 82 °F ) Programmed default schedules: Unoccupied heating setpoint = 18 °C ( 65 °F ) Monday through Sunday Fahrenheit scale Occupied time is: 12 00 AM Unoccupied time is: 11:59 PM There will be a 1 minute unoccupied period every night at 11:59 PM with this default configuration.

A) Override an unoccupied period Override schd Y/N This menu will appear only when the thermostat is in unoccupied mode. The unoccupied mode is enabled either by the internal timer scheduling or by a remote NSB contact via DI1 or DI2. If DI1 or DI2 is configured to operate as a remote temporary override contact, this menu will be disabled. Answering yes to this prompt will cause the thermostat to go into occupied mode for an amount of time equal to the parameter “TOccTime” (1 to 12 hours).

B) Resume regular scheduling Resume schd Y/N This menu does not appear in regular operation. It will appear only when the thermostat is in: • Unoccupied override mode • Permanent occupied • Permanent unoccupied Answering “Yes” to this question will cause the thermostat to resume the regular programmed setpoints & scheduling. More than one derogation to regular programming can be active and cancelled at the same time. Ex.: the thermostat can be in Permanent occupied mode while having a temporary occupied cooling setpoint activated. The resume key will cancel both derogation’s at the same time. 6 C) Temperature setpoints RoomTemp set Y/N This menu permits the adjustment of all temperature setpoints (occupied and unoccupied) as well as the desired temperature units (°F or °C) Cooling setpoint Heating setpoint Cooling setpoint Heating setpoint °F or °C Occupied mode Occupied mode Unoccupied mode Unoccupied mode display setting

Cool No next → Heat No next → Unocc CL No next → Unocc HT No next → °F or °C No next → set? Y/N Yes down ↓ set? Y/N Yes down ↓ set? Y/N Yes down ↓ set? Y/N Yes down ↓ set? Y/N Yes down ↓ Cool Use ▲▼ Heat Use ▲▼ Unocc CL Use ▲▼ Unocc HT Use ▲▼ Units Use ▲▼ 70.0 °F To set value 68.00 °F To set value 80.0 °F To set value 60.0 °F To set value °F To set value

D) System mode setting Sys mode set Y/N

This menu is accessed to set system mode operation Use ▲▼ to set value, Yes key to confirm Sys mode auto Automatic mode Automatic changeover mode between heating and cooling operation Sys mode cooling Cooling mode Cooling operation mode only Sys mode heating Heating mode Heating operation mode only Sys mode emergency Emergency heat mode ( heat pump models only ). Forced auxiliary heat operation mode only Sys mode Off mode Normal cooling or heating operation disabled. If enabled in installer parameters, only the off automatic heating frost protection at 42 °F ( 5.6 °C ) is enabled

E) Fan mode setting

Fan mode set Y/N This section of the menu is permits the setting of the fan mode operation. Use ▲▼ to set value, Yes key to confirm

Fan mode On On fan mode Fan is on continuously, even when system mode is OFF.

Fan mode Auto Automatic fan mode Fan cycles on a call for heating or cooling for both occupied & unoccupied periods.

Fan mode Smart fan mode During occupied periods, fan is on continuously. In unoccupied mode, fan cycles on a call Smart for heating or cooling.

F) Schedule set (2 events) Scheduling can have 2 or 4 events per day. This is set in the configuration menu as per parameter (2/4event )

Schedule set Y/N This section of the menu permits the user to set the whether 2 or 4 events is needed. Each day can be tailored to specific schedules if needed. • 2 events can be programmed per day. • Occupied & unoccupied periods can be set for each day. Monday timer Tuesday timer Wednesday timer Other days are identical Schedule set Schedule set Schedule set

Monday No next → Tuesday No next → Wednesd No next → Selects the day to be programmed or set? Y/N Yes down ↓ set? Y/N Yes down ↓ set? Y/N Yes down ↓ modified Yes key to access day scheduling, No key to jump to next day Occupied No next → Occupied No next → Occupied No next → Yes = Daily schedules will be accessed Day? Y/N Yes down ↓ Day? Y/N Yes down ↓ Day? Y/N Yes down ↓ No = Unoccupied mode all day Yes key to access day scheduling, No key to jump to next day Copy Y/N Yes next → Copy Y/N Yes next → Yes = Will copy previous day schedule Previous No down ↓ Previous No down ↓ No = Daily schedules will be accessed Yes key to copy previous day, No key to set new time value for each day Occupied Use ▲▼ Occupied Use ▲▼ Occupied Use ▲▼ Sets Event # 1 Occupied time 00:00 AM To set value 00:00 AM To set value 00:00 AM To set value Will activate occupied setpoints Use ▲▼ to set value, Yes key to confirm Unoccup Use ▲▼ Unoccup Use ▲▼ Unoccup Use ▲▼ Sets Event # 2 Unoccupied time 00:00 AM To set value 00:00 AM To set value 00:00 AM To set value Will activate unoccupied setpoints Use ▲▼ to set value, Yes key to confirm

Typical examples of a 2 event office schedule Event Period #1 - Event #1 Period #1 - Event #2 Note: 12:00 PM = Noon Occupied Unoccupied 12:00 AM = Midnight Cool Heat Cool Heat Daily Setpoint 72 °F 70 °F 80 °F 62 °F Occupancy Monday 7.00 AM 6.00 PM Day time only Tuesday 7.00 AM 6.00 PM Day time only Wednesday 7.00 AM 6.00 PM Day time only Thursday 7.00 AM 6.00 PM Day time only Friday 7.00 AM 6.00 PM Day time only Saturday 12.00 PM * 12.00 PM * Unoccupied Sunday 12.00 PM * 12.00 PM * Unoccupied *Programming consecutive events to the same time will cause the thermostat to choose the last event as the time at which it will set its schedule. In the above example, the thermostat will control to the unoccupied set point until 7:00 AM Monday. ** To program a day as occupied for 24 hours, set that day Occupied time to 12:00 AM and Unoccupied time to 11:59 PM There will be a 1 minute unoccupied period every night at 11:59 PM with this schedule configuration. 7 G) Schedule set (4 events)

Schedule set Y/N This section of the menu permits the user to set the whether 2 or 4 events is needed. Each day can be tailored to specific schedules if needed. • 4 events can be programmed per day. • Occupied & Unoccupied periods can be set for each day. • Programming the 3 rd. & 4 th. events to the same time will cancel the last period.

Ex. #1 Four event retail establishment schedule Event Period 1 - Event 1 Period 1 - Event 2 Period 2 - Event 3 Period 2 - Event 4 Setpoint Occupied Unoccupied Occupied Unoccupied Cool Heat Cool Heat Cool Heat Cool Heat Daily 72 °F 70 °F 80 °F 62 °F 72 °F 70 °F 80 °F 62 °F Occupancy Monday 7.00 AM 5.00 PM 12.00 PM * 12.00 PM * Day time only Tuesday 7.00 AM 5.00 PM 12.00 PM * 12.00 PM * Day time only Wednesday 7.00 AM 5.00 PM 12.00 PM * 12.00 PM * Day time only Thursday 7.00 AM 5.00 PM 7.00 PM 10.30 PM Day/evening time only Friday 7.00 AM 5.00 PM 7.00 PM 10.30 PM Day/evening time only Saturday 12.00 PM * 12.00 PM * 12.00 PM * 12.00 PM * Unoccupied Sunday 12.00 PM * 12.00 PM * 12.00 PM * 12.00 PM * Unoccupied * Programming events to the same time will cancel the last period and leave the thermostat in unoccupied mode *Programming consecutive events to the same time will cause the thermostat to choose the last event as the time at which it will set its schedule. In the above example for Saturday, the thermostat will control to the occupied set point from 8:00 AM until 11:59 PM. Since it is desired to be in occupied mode throughout the night, then it is necessary to program the first event on Sunday at 12:00 AM. The thermostat will force a one minute unoccupied period for a one minute period (between 11:59 PM and 12:00 AM on Saturday)

H) Clock/Day Settings

Clock set Y/N This section of the menu permits the user to set the time and day.

Time setting Day setting Time format setting

Time No next → Day No next → 12/24hrs No = exit set? Y/N Yes down ↓ set? Y/N Yes down ↓ set? Y/N Yes down ↓ Time Use ▲▼ Day Use ▲▼ 12/24hrs Use ▲▼ 0:00 To set value Monday To set value 12 hrs To set value

J) Schedule hold

Schedule hold Y/N • This section of the menu permits the user to set a permanent schedule hold, which bypasses the internal thermostat scheduling. • The permanent schedule hold function is typically used for non-scheduled events that extend for various periods of time. • Enabling a permanent occupied or permanent unoccupied schedule hold will cancel any active override. • The use of temporary setpoints during permanent hold is permitted. The duration of the temporary setpoint is as set per the OVERRIDE parameter. Ex. 3 hours

Use ▲▼ to set value, Yes key to confirm Schedule resume Resume regular scheduling cancels the permanent hold and re-enables the regular programming as set per internal scheduling or as per remote NSB via one of the DI’s configured as remote NSB. This action can also by accomplished by using the Resume menu. Any temporary setpoint that are active will be left active for the duration of the period as set per the TOccTime parameter.

Schedule occ hold Hold permanent occupied forces the thermostat into a permanent occupied mode using the occupied setpoints. All timed scheduling functions are by-passed. The PERMANENT OCCUPIED status will appear in the automatic status scroll. The permanent occupied override can be cancelled using the Resume menu. If the menu key is pressed, the Resume schedule menu will appear. Answering Yes to this question will re-enable the regular programmed scheduling as dictated by the current time.

Schedule uno hold Hold permanent unoccupied forces the thermostat into a permanent unoccupied mode using the unoccupied setpoints. All timed scheduling functions are by-passed. The PERMANENT UNOCCUPIED status will appear in the automatic status scroll. The permanent unoccupied override can be cancelled using the Resume menu. If the menu key is pressed, the Resume schedule menu will appear. Answering Yes to this question will re-enable the regular programmed scheduling as dictated by the current time. 8 Configuration parameters ( Accessible using the hidden CONFIG KEY, remove thermostat cover to access )

1. DI 1 Digital input no.1 configuration. Default value = 9. Heat cph Heating stages cycles per hour None Default value = 4 C.P.H. For multi stage models, heat CPH applies to Open contact input = function not energized W1 & W2. For heat pump models, heat CPH applies to W1 only Closed contact input = function energized (Emergency heat ) Will set the maximum number of cycles per hour None, No function will be associated with the input under normal control operation. It represents the number of time the Rem NSB, remote NSB timer clock input. Will disable the internal equipment will turned on and off in one hour. Note that a higher CPH scheduling of the thermostat. The scheduling will now be set as will represent a higher accuracy of control at the expense of wearing per the digital input. The time is still displayed as information, but mechanical components faster. 3, 4, 5, 6,7 & 8 C.P.H. the menu part related to scheduling is disabled and no longer accessible 10. cool cph Cooling stages cycles per hour. Open contact = occupied setpoints Default value = 4 C.P.H. For multi stage models, cool CPH applies to Closed contacts = unoccupied setpoints Y1 & Y2. For heat pump models, cool CPH applies to Y1 & Y2 in RemOVR Temporary override remote contact. Disables all cooling and heating. override menu function of the thermostat. The override function is now controlled by a manual remote momentarily closed contact. 11. Deadband Minimum deadband. Default value = 2.0 °F When configured in this mode, the input operates in a toggle ( 1.1 °C ). Minimum deadband value between the heating and cooling mode. With this function enabled it is now possible to toggle setpoints. If modified, it will be applied only when any of the setpoints between unoccupied & occupied setpoints for the amount of time are modified. 2, 3 or 4 °F ( 1.0 to 2.0 °C ) set by parameter (TOccTime) temporary occupancy time. When override is enabled, an Override status message will be displayed 12. fan cont Fan control. Default value = On Filter, a back-lit flashing Filter alarm will be displayed on the For multi stage models, fan control applies to W1 & W2 thermostat LCD screen when the input is energized For heat pump models, fan control applies to W1 only (Emergency Service, a back-lit flashing Service alarm will be displayed on the heat) When selecting On; the thermostat in all cases will always thermostat LCD screen when the input is energized control the fan (terminal G). Valid for On or Auto fan mode. When selecting Off; the fan ( terminal G ) when heating stages ( terminals 2. DI 2 Digital input no. 2 configuration W1 & W2 ) are solicited will not be energized. The fan in this case will Default value = None be controlled by the equipment fan limit control. Valid only for Auto fan Same as above. mode. On fan mode will leave the fan always on. On or Off It is possible to configure both inputs to have the same function. 13. fan del Fan delay. Default value = Off 3. lockout Keypad lockout levels. Fan delay extends fan operation by 60 seconds after the call for Default value = 0 No lock heating or cooling ends. Valid only for Auto fan mode. “On” fan mode 0 = No lock will leave the fan always on. Off or On 1 = Low level 2 = High level (see chart below) Resume to Temperature System Level Fan mode setting Schedules setting Clock setting Permanent hold scheduling setpoints mode setting Resume RoomTemp Sys mode Fan mode Schedule Clock Schedule sched Y/N set Y/N set Y/N set Y/N set Y/N set Y/N hold Y/N 0 Yes access Yes access Yes access Yes access Yes access Yes access Yes access 1 Yes access No access Yes access Yes access No access Yes access Yes access 2 No access No access No access No access No access Yes access No access 4. pwr del Power-up delay. Default value = 10 seconds 14. Com addr Thermostat networking MAC address. On initial power up of the thermostat ( each time 24 Vac power Default value = 1 Range is: 0 to 127. Range 128 to 255. These are supply is removed & re-applied ) there is a delay before any used for slave device operation. Once set at the device, the address operation is authorized (fan, cooling or heating). This can be used to can be changed through the network. sequence start up of multiple units / thermostat in one location. 10 to 120 seconds 15. ToccTime This parameter set the duration of the temporary setpoints and the override when the thermostat is in 5. Frost pr Frost protection enabled. Default value = Off unoccupied mode. This function is enabled with either the arrows On heat pump models the system mode will be forced to (direct access to temporary setpoints), by the menu or by DI1 or DI2 EMERGENCY mode if frost protection is activated. configured as remote override input. 0,1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 Off: no frost protection On: frost protection enabled in all system & 12 hours mode 42 °F ( 5.6 °C )Frost protection is enabled even in system Off mode. 16. cal RS Room air temperature sensor calibration. Off or On Default value = 0.0 °F or °C Offset that can be added/subtracted to actual displayed room temperature. ± 5.0 °F ( ± 2.5 °C ) 6. heat max Maximum heating setpoint limit. Default value = 90 °F ( 32 °C ) Maximum occupied & unoccupied 17. cal OS Outside air temperature sensor calibration. heating setpoint adjustment. Default value = 0.0 °F or °C Offset that can be added/subtracted to Heating setpoint range is: 40 to 90 °F ( 4.5 to 32.0 °C ) actual displayed outside air temperature. ± 5.0 °F ( ± 2.5 °C ) 7. cool min Minimum cooling setpoint limit. 18. H stage Number of heating stages. Applicable to 2 stage Default value = 54 °F ( 12 °C ). Minimum occupied & unoccupied models only. Default value = 2 stages. For heat pump models, H cooling setpoint adjustment. stage is limited to 1 stage only (W1 – Aux. Heat) Cooling setpoint range is: 54 to 100 °F ( 12.0 to 37.5 °C ) 19. C stage or HP stage Number of cooling 8. anticycle Minimum on/off time operation for stages stages. 2 stages model only. Default value = 2 stages Default value = 2 minutes For heat pump models, HP stage selects the number of compressor Anti-short cycling can be set to 0 minutes for equipment that posses stages. Will revert the operation of 2 stage thermostat to single stage their own anti cycling protection operation only when the second cooling step is not needed. 1 or 2 stages. 9 20. H lock Outside air temperature heating lockout 28. re valve Reversing valve operation O/B. Default value = 120 °F ( 49 °C) Default value = O Heat pump reversing valve operation. O will Disables heating stage operation based on outdoor air temperature. energize the valve in cooling operation. Function will only be enabled if OS ( outside air temperature sensor B will energize the valve in heating operation. ) is connected. From -15 °F up to 120 °F ( -26 °C up to 49 °C ) O or B 21. C lock Outside air temperature mechanical cooling 29. comp/aux Compressor/auxiliary interlock. Default value = lockout. Off. Sets the operation and interaction mode of the heat pump with Default value = -40 °F ( -40 °C ). Disables cooling stage operation the auxiliary heat. Interlock Off. In Heating mode. If the heat pump based on outdoor air temperature. On economizer model, free is not able to satisfy the heating setpoint, the auxiliary heat will be cooling will not be disabled by this function. Function will only be energized at the same time as the heat pump stage. Typically applies enabled if OS ( outside air temperature sensor ) is connected. -40 when the air handler heat pump coil is installed before the auxiliary °F to 95 °F ( -40 °C to 35 °C ) heat. ( all electric systems ) Interlock On. In Heating mode. If the heat pump is not able to satisfy the heating setpoint, the auxiliary heat 22. 2/4event Number of events configuration. will be energized and the heat pump will be cut off. Typically applies Default value = 2 event when the air handler heat pump coil is installed after the auxiliary 2 events, will set up programming for the following heat. ( add on systems ) There is a 2 minute delay to restart the heat Event 1 is for Occupied setpoint -- Event 2 is for Unoccupied pump, when the auxiliarty heat is shut down. setpoint Off or On 4 events, will set up programming for the following Event 1 is for Occupied setpoint -- Event 2 is for Unoccupied Economizer models only setpoint Event 3 is for Occupied setpoint -- Event 4 is for Unoccupied 30. chngstpt Changeover setpoint. Default value = 55 °F ( 13.0 setpoint °C ) In Cooling mode. The outside air temperature value at which the cooling will be switched over from mechanical ( compressor ) to free 23. aux cont Auxiliary contact configuration. This contact cooling ( economizer ) 14 to 70 °F ( -10.0 to 21.0 °C ) can be used to energize peripheral devices such as: lighting equipment, exhaust fans, economizers, etc. This contact will 31. min pos Minimum position. Default value = 0%. Outside air operate in parallel with the internal occupied/unoccupied schedule damper minimum position. Will be active only when fan is on ( G of the thermostat or the remote NSB contact if DI1 or DI2 is used. terminal ) and the internal or remote scheduling is in occupied mode. When the system is in OFF mode, the contactConfigured will remain Occupied in its UnoccupiedWhen internal or remote scheduling is in unoccupied mode and/or fan unoccupied N.O. Closed Opened is off, minimum position will be set to 0%. 0 to 100 % = 0 to 10 Vdc status independently of the N.C. Opened Closed output range. occupied / unoccupied schedule. Outside air percentage 0% 5% 10% 15% 20% 25% 30% Setting for 0-10 Vdc Autuator 0% 5% 10% 15% 20% 25% 30% 24. Prog rec Progressive recovery enable. Default value Setting for 2-10 Vdc Autuator 0 to 20% 24% 28% 32% 36% 40% 44% = Off Progressive recovery is automatically disabled if DI 1 and / or DI 2 32. C mech Mechanical cooling allowed. are configured remote NSB. Off, = no progressive recovery. The Default value = Off. programmed occupied schedule time is the time at which the system In Cooling mode. Allows the operation of the mechanical cooling if will restart. On, = progressive recovery active. The programmed the free cooling (economizer) cannot maintain the cooling setpoint. occupied schedule time is the time at which the desired occupied Off Typically applies when the MS ( mixed air temperature sensor ) is temperature will be attained. The thermostat will automatically installed after the mechanical cooling refrigeration coils. In this case, optimize the equipment start time. In any case, the latest a system mechanical cooling will never operate at the same time as free will restart is 10 minutes prior to the occupied period time. cooling. On Typically applies when the MS ( mixed air temperature sensor ) is installed before the mechanical cooling refrigeration coils in the Heat Pump models only mixing plenum. In this case, mechanical cooling is allowed when the 25. high bp High balance point. Default value = 90 °F ( free cooling ( economizer operation ) cannot maintain the cooling 32.0 °C ) setpoint. Off or On In Heating or Auto mode, it is the outside air temperature value at 33. mix stpt Mixed air setpoint. which the auxiliary heat will be cut off. Above that value, only the Default value = 55 °F ( 13.0 °C ). Free cooling mixed air setpoint heat pump will be used to maintain the heating setpoint. Function when economizer mode is enabled. 50 to 90 °F ( 10.0 to 32.0 °C ) will only be enabled if OS ( outside air temperature sensor ) is connected. 34. MS dis Display mixed air temperature. Economizer model 34 to 90 °F ( 1.0 to 32.0 °C ) only, only if sensor is installed Used as diagnostic / service help to troubleshoot and diagnose 26. Low balance point. Default value = -12 °F ( -24 low bp economizer operation. °C ) In Heating, Cooling or Auto mode, it is the outside air temperature value at which the heat pump operation will be cut off. Below that Note: value, only the auxiliary heat will be used to maintain the heating When the outside air sensor is not connected or is setpoint. Function will only be enabled if OS ( outside air temperature sensor ) is connected. shorted, the thermostat bypasses: -40 to 30 °F ( -40 to -1.0 °C ) • The heating lockout • The cooling lockout 27. Comf/eco Comfort or economy mode. Default value = Comfort. Sets the operation and interaction mode • The low balance point of the heat pump with the auxiliary heat. Comfort mode. In • The high balance point Heating mode. If the heat pump is not able to satisfy the heating setpoint, the auxiliary heat will be energized to satisfy the same Emergency mode bypasses heating lockout and setpoint. Economy mode. In Heating mode. If the heat pump is not permits auxiliary heating whenever a heating demand able to satisfy the heating setpoint, the auxiliary heat will be energized to satisfy only when the temperature has dropped 2.0 °F ( occurs 1.1 °C ) below the heating setpoint. Selecting economy mode will add a deadband between the heatpump & auxiliary heat in heating mode. The actual temperature maintained will be lower than the true heating setpoint to maximize the heat pump operation. When the outdoor air temperature drops below the low balance point, the deadband will be eliminated and the auxiliary heat will maintain the true heating setpoint alone. Economy mode. In Emergency mode. If Emergency heat mode is selected, the setpoint maintained, will be the heating setpoint.

. 10 Troubleshooting guide All models

Symptom Possible Cause Corrective Action No display on the Absent or incorrect supply 1. Check power supply voltage between C & RC to be from thermostat voltage 19-30 Vac 2. Check for tripped fuse or circuit breaker Overloaded power transformer Verify that the transformer used is powerful enough (enough VA’s) to supply all controlled devices including the thermostat

Keyboard menu does not Keyboard locked Change configuration parameter LOCKOUT to value “0” to access all functions access all levels of the menu

Temperature setpoints Temporary setpoint active for a To do a permanent change to the setpoints you must enter revert to original value period of time set by parameter the menu “RoomTemp Set” and modify the setpoints at after a certain time period TOccTime desired temperature

Thermostat will not call for Wrong mode selected Select heating mode heating Thermostat in Unoccupied mode Select Occupied Hold in Schedule hold or Override to force the thermostat Occupied heating setpoint Anticycle delay active Wait, the anticycling period will end and the equipment will start Heating setpoint is satisfied Raise the Heating setpoint Heating lockout attained 1. Mode is locked out based on outside air temperature 2. Change configuration parameter H Lock to value 120 °F ( 49 °C ) to by-pass lockout Wiring error 1. Start the Fan by forcing the Fan ON mode 2. Put a jumper across terminals RH & W1. The heating should come ON. If it does not, verify wiring and check if a jumper is required between RC & RH

Thermostat will not call for Wrong mode selected Select cooling mode cooling Thermostat in Unoccupied mode Select Occupied Hold in Schedule hold or Override to force the thermostat Occupied cooling setpoint Anticycle delay active Wait, the anticycling period will end and the equipment will start Cooling setpoint is satisfied Lower the cooling setpoint Cooling lockout attained 1. Mode is locked out based on outside air temperature 2. Change configuration parameter C Lock to value -40 °F ( -40 °C ) to by-pass lockout Wiring error 1. Start the Fan by forcing the Fan ON mode 2. Put a jumper across terminals RC & Y1. The cooling should come ON. If it does not, verify wiring

The thermostat will not Wrong mode selected 1. Start the Fan by forcing the Fan ON mode turn on the fan Wiring error 2. Put a jumper across terminals RC & G. The fan should come ON. If it does not, verify wiring

Digital display shows Defective display Replace thermostat missing digits or erratic segments 11 Troubleshooting guide Heatpump models

Auxiliary heat does not Wrong mode selected Select emergency heat mode operate Thermostat in Unoccupied mode Select Occupied Hold in Schedule hold or Override to force the thermostat Occupied heating setpoint Anticycle delay active Wait, the anticycling period will end and the equipment will start Heating setpoint is satisfied Raise the Heating setpoint High Balance point attained 1. Mode is locked out based on outside air temperature 2. Change configuration parameter High BP to value 90 °F ( 32 °C ) to by-pass lockout Heating lockout attained 1. Mode is locked out based on outside air temperature 2. Change configuration parameter H Lock to value 120 °F ( 49 °C ) to by-pass lockout Wiring error 1. Start the Fan by forcing the Fan ON mode 2. Put a jumper across terminals RH & W1. The heating should come ON. If it does not, verify wiring and check if a jumper is required between RC & RH

Heat pump does not Wrong mode selected Select heating mode operate in heating mode Thermostat in Unoccupied mode Select Occupied Hold in Schedule hold or Override to force the thermostat Occupied heating setpoint Anticycle delay active Wait, the anticycling period will end and the equipment will start Heating setpoint is satisfied Raise the Heating setpoint Low Balance point attained 1. Mode is locked out based on outside air temperature 2. Change configuration parameter Low BP to value -12 °F ( -24 °C ) to by-pass lockout Heating lockout attained 1. Mode is locked out based on outside air temperature 2. Change configuration parameter H Lock to value 120 °F ( 49 °C ) to by-pass lockout Wiring error 1. Start the Fan by forcing the Fan ON mode 2. Put a jumper across terminals RH & W1. The heating should come ON. If it does not, verify wiring and check if a jumper is required between RC & RH Wrong reversing valve 1. Wrong selection of parameter Re Valve configuration 2. Select O will energize the valve in cooling operation. Valve is normally heat. 3. Select B will energize the valve in heating operation. Valve is normally cool. 12 BACnet profile overview Viconics BACnet communicating thermostats are master devices on a BACnet MS/TP network. BACnet is a standard application and communications protocol developed under the auspices of ANSI/ASHRAE specifically for the building automation industry. The protocol is defined in ANSI/ASHRAE Standard 135-2001.

Product Description: The T7600 series BACnet communicating single stage and multi-stage communicating thermostat has been specifically designed to control packaged and split HVAC equipment on a BACnet MS-TP® network.

MS/TP EIA-485 Characteristics

Parameter Details Media Shielded, twisted pair Characteristic Impedance 100-130 ohms Distributed capacitance Less than 100 pF per metre (30 pF per foot) Maximum length per segment 1200 metres (4000 feet) Note: AWG 18 cable Polarity Polarity sensitive Multi-drop Daisy-chain (no T connections) Terminations 120 ohms at each end of each segment Network Bias Resistors 510 ohms per wire (max. of two sets per segment) Maximum number of nodes per segment 32 Maximum number of nodes per network 255 * Baud rate 9600, 19200, 38400, 76800 Default baud rate 9600 * BACnet MSTP supports only 128 nodes as masters.

Supported BACnet Services The BACnet communicating thermostat meets all requirements for designation as an Application Specific Controller (B-ASC) except for the Device Management – Device Communication Control – B service. This service is not supported. The BACnet thermostat series supports the following BACnet Interoperability Building Blocks (BIBBs). Application Service Designation Data Sharing – Read Property - B DS-RP-B Data Sharing – Write Property - B DS-WP-B Device Management – Dynamic Device Binding - B DM-DDB-B Device Management – Dynamic Object Binding - B DM-DOB-B Device Management – Time Synchronization - B DM-TS-B

Note 1: The Thermostat does not support the full date therefore it cannot claim conformance to DM-TS-B. The local thermostat does not have the Local_Time or Local_Date properties. Note 2: The B-SA and B-ASC designations do not require conformance to the DM-TS-B service. Note 3: The thermostat does not support segmented requests or responses. Note 4: The thermostat does not support RPM (Read Property Multiple). 13 Object Table and Types Supported:

Type and Object Name Object Property Thermostat Parameter Instance T7600 Device Model_Name Thermostat model number Application_Software_Version Thermostat version Major_Version N/A MS/TP_Address BACnet Address MS/TP_Baud_Rate N/A

Type and Object Name Object Property Instance T7600A1000B T7600B1000B T7605B1000B T7600H1000B T7652A1000B T7652B1000B T7656B1000B T7652H1000B

Room Temperature AV 7 Present_Value √√√√√√√√ Room Temp Override BV 8 Present_Value √√√√√√√√ Outdoor Temperature AV 9 Present_Value √√√√√√√√ Outdoor Temp Override BV 10 Present_Value √√√√√√√√ System Mode MSV 13 Present_Value √√√√√√√√ Fan Mode MSV 14 Present_Value √√√√√√√√

Control Output Group Present_Value √ √ √ √ √ √ √ √ PI Heating Demand AV 18 Present_Value √ √ √ √ √ √ √ √ PI Cooling Demand AV 19 Present_Value √ √ √ √ √ √ √ √ Economizer Output AV 20 Present_Value √ √

Supply Temperature AI 15 Present_Value √√

Type and Object Name Object Property Instance T7600A1000B T7600B1000B T7605B1000B T7600H1000B T7652A1000B T7652B1000B T7656B1000B T7652H1000B

Controller Status Group Present_Value √ √ √ √ √ √ √ √ AUX BI 22 Present_Value √ √ √ √ G Fan BI 23 Present_Value √ √ √ √ √ √ √ √ Y1 Cool BI 24 Present_Value √ √ √ √ √ √ √ √ Y2 Cool BI 25 Present_Value √ √ √ √ √ √ W1 Heat BI 26 Present_Value √ √ √ √ √ √ √ √ W2 Heat or Reversing BI 27 Present_Value √ √ √ √ √ √ Valve DI 1 Status BI 29 Present_Value √ √ √ √ √ √ √ √ DI 2 Status BI 30 Present_Value √ √ √ √ √ √ √ √

Controller Alarms Group Present_Value √ √ √ √ √ √ √ √ Frost Alarm BI 32 Present_Value √ √ √ √ √ √ √ √ Clock Alarm BI 33 Present_Value √ √ √ √ √ √ √ √ Filter Alarm BI 34 Present_Value √ √ √ √ √ √ √ √ Service Alarm BI 35 Present_Value √ √ √ √ √ √ √ √

Temperature Setpoints Group Present_Value √ √ √ √ √ √ √ √ Occupied Heat Setpoint AV 37 Present_Value √ √ √ √ √ √ √ √ Occupied Cool Setpoint AV 38 Present_Value √ √ √ √ √ √ √ √ Unoccupied Heat Setpoint AV 39 Present_Value √ √ √ √ √ √ √ √ Unoccupied Cool Setpoint AV 40 Present_Value √ √ √ √ √ √ √ √

Keypad Lockout MSV 16 Present_Value √√√√√√√√ 14

Type and Object Name Object Property Instance T7600A1000B T7600B1000B T7605B1000B T7600H1000B T7652A1000B T7652B1000B T7656B1000B T7652H1000B

General Options 1 Group Present_Value √ √ √ √ √ √ √ √ Temperature Scale BV 42 Present_Value √ √ √ √ √ √ √ √ Heating Setpoint Limit AV 43 Present_Value √ √ √ √ √ √ √ √ Cooling Setpoint Limit AV 44 Present_Value √ √ √ √ √ √ √ √ Heating Lockout Temperature AV 45 Present_Value √ √ √ √ √ √ √ √ Cooling Lockout Temperature AV 46 Present_Value √ √ √ √ √ √ √ √ Deadband AV 47 Present_Value √ √ √ √ √ √ √ √ Heating CPH MSV 48 Present_Value √ √ √ √ √ √ √ √ Cooling CPH MSV 49 Present_Value √ √ √ √ √ √ √ √ Frost Protection BV 50 Present_Value √ √ √ √ √ √ √ √

General Options 2 Group Present_Value √ √ √ √ √ √ √ √ Power-up Delay AV 52 Present_Value √ √ √ √ √ √ √ √ Temporary Occupancy Time MSV 53 Present_Value √ √ √ √ √ √ √ √ Fan Control BV 54 Present_Value √ √ √ √ √ √ √ √ Min. On/Off Time MSV 55 Present_Value √ √ √ √ √ √ √ √ Fan Purge Delay BV 56 Present_Value √ √ √ √ √ √ √ √ DI 1 Configuration MSV 57 Present_Value √ √ √ √ √ √ √ √ DI 2 Configuration MSV 58 Present_Value √ √ √ √ √ √ √ √

Program Options Group Present_Value √ √ √ √ Aux Contact BV 60 Present_Value √ √ √ √ Progressive Recovery BV 61 Present_Value √ √ √ √ Event Display MSV 62 Present_Value √ √ √ √

Type and Object Name Object Property Instance T7600A1000B T7600B1000B T7605B1000B T7600H1000B T7652A1000B T7652B1000B T7656B1000B T7652H1000B

Stages Group Present_Value √ √ √ √ √ √ Heating Stages MSV 64 Present_Value √ √ √ √ √ √ Cooling Stages or Heat Pump MSV 65 Present_Value √ √ √ √ √ √ Stages

Economizer Group Present_Value √ √ Economizer Changeover AV 68 Present_Value √ √ Setpoint Economizer Minimum Position AV 69 Present_Value √ √ Mechanical Cooling BV 70 Present_Value √ √ Mixed Air Setpoint AV 71 Present_Value √ √

Heat Pump Group Present_Value √ √ High Balance Point AV 73 Present_Value √√ Low Balance Point AV 74 Present_Value √√ Comfort Mode BV 75 Present_Value √√ Reversing Valve BV 76 Present_Value √√ Compressor Interlock BV 77 Present_Value √√

Occupancy MSV 11 Present_Value √√√√√√√√

Schedule Schedule 1 Present_Value √√√√ Weekly_Schedule Occupancy Status Monday Tuesday Wednesday Thursday Friday Saturday Sunday • The Weekly_Schedule property will contain all the schedules for the week. 15 MAC Address The MAC address can be set locally through the configuration parameter (Com Addr) communication address. • The range is: 0 to 127 with a factory default address of 1. • Do not use range 128 to 255. These are not supported for Master device operation. • If a value above 127 is applied, the thermostat will behave as if it was a slave device and will not be able to respond to the BACnet queries to auto discover devices on the network.

Once set at the device, the address can be changed through the network. The value is available as a writable property of the Device object. Writing the property value will write the new value to the Thermostat. The updates will be applied immediately to the MS/TP communications port.

Baud Rate On power up in its default mode of operation, the thermostat will automatically detect current Baud rate and match its own baud rate to the baud rate of the network. Automatic baud rate detection will occur when the MS/TP communications port is initialized. The thermostat will go “online” to the BACnet network only after it has successfully detected the baud rate and initialization of its BACnet object set has been completed. The supported range of values for the baud rate will be: 9600, 19200, 38400 and 76800 bps. The default being 9600 If the thermostat looses communication with the BACnet network, it will resume the automatic baud detection mode. The module will go “online” to the BACnet network again only after it has successfully detected the baud rate. This feature allows the thermostat to match an online baud rate change made at the MS/TP master. The automatic baud detection feature may be disabled by writing a fixed baud rate into the thermostat. The baud rate value is available as a writable property of the Device object. Writing a value to the property will save the new value in non-volatile memory. The update will be applied immediately to the MS/TP communications port. If during initialization, the non-volatile memory is found to contain a baud rate, automatic baud detection is disabled and the stored baud rate will be applied to the MS/TP communications port. Automatic baud rate detection may be restored by writing a “blank” baud rate to the baud rate property.

Device Object Name The device object name must be unique from any other BACnet device object name on the entire BACnet network (i.e. not just the MS/TP sub-network.) In order to ensure the name is unique for all Thermostat on the same MS/TP network, the default name are: Default Device object name: T7600-address For example: T7600-123, where 123 is the MAC address of this particular device. If the default name conflicts with another device name, the name may be changed from the BACnet network. If the BACnet device object name is updated from the network, the change will override the default value and will be applied immediately to the MS/TP communications interface. If the device object name is overridden, it will be stored in non-volatile memory in the communications module. The default name handling may be restored by writing a “blank” name to the Object Name property.

Device Object ID The device object ID must be unique from any other BACnet device object ID on the entire BACnet network (i.e. not just the MS/TP sub-network.) In order to ensure the ID is unique for all thermostat on the same MS/TP network, the default ID will consist of the product name summed with the MS/TP address of the device. The default value will be: Default Device object ID: 76000 + address For example: 76123, where 123 is the address of the particular device. If the default object ID conflicts with another device ID, the ID may be changed from the BACnet network. If the BACnet device object ID is updated from the network, the change will override the default value and will be applied immediately to the MS/TP communications interface. If the device object ID is overridden, it will be stored in non-volatile memory in the communications module. The default ID handling may be restored by writing a “blank” ID to the Object ID property.

Room Temperature Object

Property Name ID BACnet Data RW Initial Value Type Object_Name 77 RW Room Temperature Present_Value 85 RW Read from Thermostat Units 117 R either: 62 (°C) or 64 (°F) Sensor_Offset 1005 REAL RW Read from Thermostat 16 Object Name – The object name cannot be changed from the BACnet network. Present_Value – The BACnet value will normally be read-only. The value will be read from the Thermostat room temperature input. If the Room Temp Override object is changed to Override, the Room Temperature Present_Value property will be BACnet write enabled and the value will no longer be read from the Thermostat. While write enabled, the BACnet value may be changed from the network (i.e. from another BACnet device.) When the value is changed from the network, the Thermostat room temperature value will be written to. This will place the Thermostat parameter in the overridden state. When the Room Temp Override object is changed to Normal, the Room Temperature Present_Value property will not accept BACnet writes. The property value will be read from the Thermostat room temperature input. This will restore the Thermostat parameter to its normal state.

Reliability – This property may have any of the following values: State Cause NO_FAULT_DETECTED Normal operation OVER_RANGE Present_Value >= 122 °F UNDER_RANGE Present_Value <= -40 °F UNRELIABLE_OTHER Thermostat parameter cannot be read

Sensor_Offset – This property will display the temperature calibration value. Writing the BACnet value will cause a new value to be written to the Thermostat. If the Temperature Scale object is set to °C, the value read from the Thermostat will be converted to °C. When the value is written to the Thermostat, it will be converted to °F.

Room Temp Override Object

Property Name ID BACnet Data RW Initial Value Type Object_Name 77 R Room Temp Override Present_Value 85 RW 0 Inactive_Text 46 R Normal Active_Text 4 R Override

Present_Value – The Room Temp Override object will be used to enable/disable BACnet writes to the Room Temperature object’s ‘Present Value’ property. The range of values will be: • 0 = Normal ( Get room temperature value from the thermostat ) • 1 = Override ( Get room temperature value from the network ) When the value is set to Override, the Room Temperature object’s ‘Present Value’ property will accept BACnet writes. The current value of the Room Temperature object will be written to the thermostat to place the thermostat space temperature parameter into override mode. Reading of the space temperature parameter will be suspended. When the value is set to Normal, the Room Temperature object’s ‘Present Value’ property will not accept BACnet writes. The thermostat space temperature parameter will be read to take it out of override mode and restore normal space temperature operation.

Outdoor Temperature Object The Outdoor Temperature object will be derived from the standard BACnet Analog Value object type. The object will support all Analog Value object properties required by BACnet. Additional properties will be added to support configuration options of the thermostats.

Property Name ID BACnet Data RW Initial Value Type Object_Name 77 R Outdoor Temperature Present_Value 85 RW Read from Thermostat Units 117 R either: 62 (°C) or 64 (°F) Sensor_Offset 1005 REAL RW Read from Thermostat

Present_Value – The BACnet value will normally be read-only. The value will be read from the Thermostat outdoor temperature input. If the Outdoor Temp Override object is changed to Override, the Outdoor Temperature Present_Value property will be BACnet write enabled and the value will no longer be read from the Thermostat. While write enabled, the BACnet value may be changed from the network (i.e. from another BACnet device.) When the value is changed from the network, the Thermostat outdoor temperature value will be written to. This will place the Thermostat parameter in the overridden state. When the Outdoor Temp Override object is changed to Normal, the Outdoor Temperature Present_Value property will not accept BACnet writes. The property value will be read from the Thermostat room temperature input. This will restore the Thermostat parameter to its normal state. 17 Reliability – This property may have any of the following values: State Cause NO_FAULT_DETECTED Normal operation OVER_RANGE Present_Value >= 122 °F UNDER_RANGE Present_Value <= -40 °F UNRELIABLE_OTHER Thermostat parameter cannot be read

Outdoor Temp Override Object

Property Name ID BACnet Data RW Initial Value Type Object_Name 77 R Outdoor Temp Override Present_Value 85 RW 0 Inactive_Text 46 R Normal Active_Text 4 R Override

Present_Value – The Outdoor Temp Override object will be used to enable/disable BACnet writes to the Outdoor Temperature object’s ‘Present Value’ property. The range of values will be: • 0 = Normal ( Get room temperature value from the thermostat ) • 1 = Override ( Get room temperature value from the network ) When the value is set to Override, the Outdoor Temperature object’s ‘Present Value’ property will accept BACnet writes. The current value of the Outdoor Temperature object will be written to the thermostat to place the thermostat outdoor temperature parameter into override mode. Reading of the outdoor temperature parameter will be suspended. When the value is set to Normal, the Outdoor Temperature object’s ‘Present Value’ property will not accept BACnet writes. The thermostat outdoor temperature parameter will be read to take it out of override mode and restore normal outdoor temperature operation.

System Mode Object Property Name ID BACnet Data RW Initial Value Type Object_Name 77 R System Mode Present_Value 85 RW Read from Thermostat Number_Of_States 74 R 5

State_Text – This property will have the following array: Index Text 1 Off 2Auto 3 Cool 4 Heat 5 Emergency

Fan Mode Object Property Name ID BACnet Data RW Initial Value Type Object_Name 77 R Fan Mode Present_Value 85 RW Read from Thermostat Number_Of_States 74 R 3

State_Text – This property will have the following array: Index Text 1On 2Auto 3 Smart

Control Output Object Property Name ID BACnet Data Type RW Initial Value Object_Name 77 R Control Output Present_Value 85 R N/A List_Of_Group_Members 53 R

List_Of_Group_Members – The following objects/properties: Object Property PI Heating Demand Present_Value, Reliability PI Cooling Demand Present_Value, Reliability * Economizer Output Present_Value, Reliability Note: The Economizer Output object will only be included if the Thermostat model supports the Economizer feature.

PI Heating Demand Object Property Name ID BACnet Data Type RW Initial Value Object_Name 77 R PI Heating Demand Present_Value 85 R Read from Thermostat Units 117 R 95 (no units) 18 PI Cooling Demand Object Property Name ID BACnet Data Type RW Initial Value Object_Name 77 R PI Cooling Demand Present_Value 85 R Read from Thermostat Units 117 R 95 (no units)

Economizer Output Object Property Name ID BACnet Data Type RW Initial Value Object_Name 77 R Economizer Output Present_Value 85 R Read from Thermostat Units 117 R 95 (no units)

Supply Temperature Object Property Name ID BACnet Data Type RW Initial Value Object_Name 77 R Supply Temperature Present_Value 85 R Read from Thermostat Units 117 R either: 62 (°C) or 64 (°F)

Controller Status Object Property Name ID BACnet Data Type RW Initial Value Object_Name 77 R Controller Status Present_Value 85 R N/A List_Of_Group_Members 53 R

List_Of_Group_Members – The following objects/properties: Object Property Inactive_Text Active_Text AUX Present_Value, Reliability Off On G Fan Present_Value, Reliability Off On Y1 Cool Present_Value, Reliability Off On Y2 Cool Present_Value, Reliability Off On W1 Heat Present_Value, Reliability Off On W2 Heat or Reversing Valve * Present_Value, Reliability Off On DI Status ** Present_Value, Reliability Activated Not Activated D2 Status ** Present_Value, Reliability Activated Not Activated

* The name of this object will be either W2 Heat or Reversing Valve depending on the model of thermostat • Reversing Valve for heat pump models. (T7600H1000B or T7652H1000B) • W2 for roof top models. (T7600A1000B, T7652A1000B, T7600B1000B, T7652B1000B, T7602B1000B or T7656B1000B)

** Object reported is the direct status of the input independently of its internal configuration. The point can be reported even if the internal configuration is set to ( None ) no function.

Controller Alarms Object Property Name ID BACnet Data Type RW Initial Value Object_Name 77 R Controller Alarms Present_Value 85 R N/A List_Of_Group_Members 53 R

List_Of_Group_Members – The following objects/properties: Object Property Inactive_Text Active_Text Frost Alarm Present_Value, Reliability Off On Clock Alarm * Present_Value, Reliability Off On Filter Alarm ** Present_Value, Reliability Off On Service Alarm ** Present_Value, Reliability Off On

* This alarm is only available on thermostats with internal scheduling with a real time clock on board. If there is a power failure longer than 6 hours, the thermostat will loose its internal time and needs to be resynchronized through the network or locally at the device. ** Points can only be reported only if DI or DI2 are configured for these specific alarms

Temperature Setpoints Object Property Name ID BACnet Data RW Initial Value Type Object_Name 77 R Temperature Setpoints Present_Value 85 R N/A List_Of_Group_Members 53 R 19 List_Of_Group_Members – The following objects/properties: Object Property Occupied Heat Setpoint Present_Value, Reliability Occupied Cool Setpoint Present_Value, Reliability Unoccupied Heat Setpoint Present_Value, Reliability Unoccupied Cool Setpoint Present_Value, Reliability

Keypad Lockout Object Property Name ID BACnet Data RW Initial Value Type Object_Name 77 R Keypad Lockout Present_Value 85 RW Read from Thermostat Number_Of_States 74 R 3 Relinquish_Default 104 RW Read from Thermostat

State_Text – This property will have the following array: Index Text 1 No Lockout 2 Level 1 3 Level 2

Program Options Object

Property Name ID BACnet Data RW Initial Value Type Object_Name 77 R Program Options Present_Value 85 R N/A List_Of_Group_Members 53 R

Object Property Range Aux Contact Present_Value, Reliability 0 = Normally Open 1 = Normally Closed Progressive Recovery Present_Value, Reliability 0 = Off 1 = Active Event Display Present_Value, Reliability 1 = 2 events 2 = 4 events

General Options Object Property Name ID BACnet Data RW Initial Value Type Object_Name 77 R General Options 1 or 2 Present_Value 85 R N/A List_Of_Group_Members 53 R

List_Of_Group_Members – The following objects/properties: Group 1 Object Property Range Temperature Scale Present_Value, Reliability 0 = °C 1 = °F Heating Setpoint Limit Present_Value, Reliability 40 °F to 90 °F Cooling Setpoint Limit Present_Value, Reliability 54 °F to 100 °F Heating Lockout Temperature Present_Value, Reliability -15 °F to 120 °F Cooling Lockout Temperature Present_Value, Reliability -40 °F to 95 °F Deadband Present_Value, Reliability 1 = 2 °F_°C 2 = 3 °F_1.5 °C 3 = 4 °F_2 °C Heating CPH Present_Value, Reliability 1 = 3 CPH 2 = 4 CPH 3 = 5 CPH 4 = 6 CPH 5 = 7 CPH 6 = 8 CPH Cooling CPH Present_Value, Reliability 1 = 3 CPH 2 = 4 CPH Frost Protection Present_Value, Reliability 0 = Off 1 = On Group 2 Object Property Power-up Delay Present_Value, Reliability 10 to 120 ( seconds ) Temporary Occupancy Time Present_Value, Reliability 1 = 0 hour 2 = 1 hour up to 13 = 12 hours Fan Control Present_Value, Reliability 0 = Off 1 = On 20

Min. On/Off Time Present_Value, Reliability 1 = 0 minutes 2 = 1 minutes 3 = 2 minutes 4 = 3 minutes 5 = 4 minutes 6 = 5 minutes Fan Purge Delay Present_Value, Reliability 0 = Off 1 = On DI 1 Configuration Present_Value, Reliability 1 = None 2 = Rem NSB 3 = Override 4 = Filter 5 = Service DI 2 Configuration Present_Value, Reliability 1 = None 2 = Rem NSB 3 = Override 4 = Filter 5 = Service

Stages Object Property Name ID BACnet Data Type RW Initial Value Object_Name 77 R Stages Present_Value 85 R N/A List_Of_Group_Members 53 R

List_Of_Group_Members – The following objects/properties: Object Property Range Heating Stages Present_Value 1 = 1 stage 2 = 2 stages Cooling Stages or HeatPump Stages * Present_Value 1 = 1 stage 2 = 2 stages

* The name of this object will be either Cooling Stages or Heat Pump Stages depending on the model of thermostat. • HeatPump Stages for heat pump models. (T7600H1000B or T7652H1000B) • Cooling Stages for roof top models. (T7600A1000B, T7652A1000B, T7600B1000B, T7652B1000B, T7602B1000B or T7656B1000B)

Economizer Object The Economizer object and its associated objects will only be created for Thermostat models that have the Economizer output option. ( T7602B1000B & T7656B1000B ) Property Name ID BACnet Data Type RW Initial Value Object_Name 77 R Economizer Present_Value 85 R N/A List_Of_Group_Members 53 R

List_Of_Group_Members – The following objects/properties: Object Property Range Economizer Changeover Setpoint Present_Value, Reliability 14 °F to 70 °F Economizer Minimum Position Present_Value, Reliability 0 to 100 % Mechanical Cooling Present_Value, Reliability 0 = Off not allowed 1 = On allowed Mixed Air Setpoint Present_Value, Reliability 50 °F to 90 °F

Heat Pump Object The Heat Pump object and its associated objects will only be created for heatpump model thermostats. ( T7600H1000B & T7652H1000B ) 21 List_Of_Group_Members – The following objects/properties: Object Property High Balance Point Present_Value, Reliability 34 °F to 90 °F Low Balance Point Present_Value, Reliability -40 °F to 30 °F Mode Present_Value, Reliability 0 = Comfort 1 = Economy Reversing Valve Present_Value, Reliability 0 = Normally Heat 1 = Normally Cool Compressor Interlock Present_Value, Reliability 0 = Off 1 = On

Occupancy Object Property Name ID BACnet Data Type RW Initial Value Object_Name 77 R Occupancy Present_Value 85 RW ‘Resume Schedule’ Number_Of_States 74 R 3

State_Text – This property will have the following array: Index Text 1 Resume Schedule * 2 Occupied 3 Unoccupied * On models with internal scheduling and a real time clock on board. This variable will release the network occupancy command to local occupancy as dictated by the local current thermostat schedule.

Schedule Object The Schedule object will be derived from the standard BACnet Schedule object type. The object will support all Schedule object properties required by BACnet. The Schedule object and its associated objects will only be created for models with internal scheduling. ( T7652A1000B, T7652B1000B, T7656B1000B & T7652H1000B )

Property Name ID BACnet Data RW Initial Value Type Object_Idenifier 75 R Object_Name 77 R Schedule Object_Type 79 R 17 Present_Value 85 R Read from Thermostat Effective_Period 32 R Weekly_Schedule 123 RW Read from Thermostat List_Of_Object_Property_ 54 R References Priority_For_Writing 88 R 16

Effective_Period – This is a BACnet required property. This property specifies a range of dates for the schedule. Since the Thermostat does not support dates, this property will be read-only and will return an empty list.

Supported BACnet Services The BACnet thermostats meet the requirements to be designated BACnet Application Specific Controllers (B-ASC). The BACnet thermostat supports the BACnet Interoperability Building Blocks (BIBBs)

BIBBs

Application Service Designation Data Sharing – Read Property - B DS-RP-B Data Sharing – Write Property - B DS-WP-B Device Management – Dynamic Device Binding - B DM-DDB-B Device Management – Dynamic Object Binding - B DM-DOB-B Device Management – Device Communication Control - B DM-DCC-B Device Management – Time Synchronization - B DM-TS-B ( Note 1 & 2 )

Note 1: The Thermostat does not support the full date therefore cannot claim conformance to DM-TS-B. The device object will not have the Local_Time or Local_Date properties. Note 2: The BACnet Application Specific Controller (B-ASC) designation does not require conformance to the DM-TS-B service.

Temperature Value Handling Thermostat temperature value is always stored in the thermostat memory as a value in °F. For all temperature objects, if the Temperature_Scale property of the Device object is set to °C, the temperature value read from the Thermostat will be converted to °C. When the value is written to the Thermostat, it will be converted to °F. Object reliability tests will be made against the °F value. 22 Communications with MS-TP BACnet Communications with BACnet will be considered on-line as long as the BACnet communications module is seeing valid frames on the BACnet network. The BACnet communications module will consider itself off-line after 10 minutes without valid MS/TP traffic. When the module goes off-line, it will release the following Thermostat parameters: • Room Temperature • Outdoor Temperature • Occupancy If the thermostat goes off-line, it may be due to a baud rate change on the MS/TP network. The module will revert to its automatic baud detection mode. The network baud rate will be detected when valid MS/TP frames are seen on the network. The module will go “on-line” to the network when a message is received that was addressed to the thermostat. Overrides of thermostat parameters will be restored only if a new BACnet write is received for the corresponding BACnet object of the parameter.

Communications Status LED Communication with the MS-TP network can be confirmed using the flashing GREEN Com Status LED. The LED is located underneath the communication adapter daughter board on the left side. Located under Flashing sequence the None, LED is OFF No power or polarity is reversed network 2 short Auto-bauding, currently searching for a network adapter 2 short followed by 1 long Network detected and thermostat available

YE N MEN ↓ ↑

Specifications Location of network status LED Communication: BACnet MS-TP protocol Memory: EEPROM Thermostat power requirements: 19-30 Vac 50 or 60 Hz; 2 VA ( RC & C ) Class 2 RC to RH jumper 2.0 Amps 48 VA maximum Operating conditions: 0 °C to 50 °C ( 32 °F to 122 °F ) 0% to 95% R.H. non-condensing Storage conditions: -30 °C to 50 °C ( -22 °F to 122 °F ) 0% to 95% R.H. non-condensing Sensor: Local 10 K NTC thermistor Resolution: ± 0.1 °C ( ± 0.2 °F ) Control accuracy: ± 0.5 ° C ( ± 0.9 °F ) @ 21 °C ( 70 °F ) typical calibrated Occupied and unoccupied setpoint range cooling: 12.0 to 37.5 °C ( 54 to 100 °F ) Occupied and unoccupied setpoint range heating: 4.5 °C to 32 °C ( 40 °F to 90 °F ) Room and outdoor air temperature range -40 °C to 50 °C ( -40 °F to 122 °F ) Proportional band for room temperature control: Both outputs: 1.1°C ( 2.0°F ) Digital inputs: Relay dry contact only across C terminal to DI1 or DI2 Contact output rating: Each relay output: ( Y1, Y2, G, W1, W2 & AU ) 30 Vac, 1 Amp. maximum 30 Vac, 3 Amp. in-rush Economizer analog output rating: 0 to 10 Vdc into 2KΩ resistance min. Economizer analog output accuracy: ± 3% typical Wire gauge 18 gauge maximum, 22 gauge recommended Dimensions: 4.94” x 3.38” x 1.13” Approximate shipping weight: 0.75 lb ( 0.34 kg ) Agency Approvals: CE ( Pending ) EN50081-1:1992 EMC Emission ( Pending ) EN50082-2:1992 EMC Immunity ( Pending ) FCC Class A Class A computing device, Subpart J of Part 15 cULus UL873 File E234137 with CCN's XAPX (US) and XAPX7 (Canada).

Drawing & dimensions Important notice All T7600 series controls are for use as operating controls only and are not safety devices. These instruments have undergone rigorous tests and verifications prior to shipment 4.94" [125 mm] to ensure proper and reliable operation in the field. Whenever a control failure could lead to personal injury and/or loss of property, it becomes the responsibility of the user / installer / electrical system designer to incorporate safety devices ( such as relays, flow switch, thermal protections, etc…) and/or alarm system 3.38" [86 mm] to protect the entire system against such catastrophic failures. Tampering of the devices or miss application of the device 1.13" [29 mm] will void warranty.

Fig.13 – Thermostat dimensions